get in line - process analysis solutions open new opportunities for improved profit and quality
TRANSCRIPT
NEXT PAGE
Grain & Feed Milling Technology is published six times a year by Perendale Publishers Ltd of the United Kingdom.All data is published in good faith, based on information received, and while every care is taken to prevent inaccuracies, the publishers accept no liability for any errors or omissions or for the consequences of action taken on the basis of information published. ©Copyright 2010 Perendale Publishers Ltd. All rights reserved. No part of this publication may be reproduced in any form or by any means without prior permission of the copyright owner. Printed by Perendale Publishers Ltd. ISSN: 1466-3872
Digital Re-print - November | December 2011 Get in line - Process analysis solutions open new opportunities for improved profit and quality
www.gfmt.co.uk
The use of NIR technology as an analyti-cal technique is far from new to the grain and feed milling industry.
In many parts of the world it has been a mainstay of grain quality analysis for more than 20 years and the benefits of the technology are well understood. So what is the next step for this technology? As with many aspects of food and agricultural quality control today, the answer lies in the field of in-line near infrared analysis.
But even in-line NIR is not a new concept. The potential benefits of moving the instru-
ment from the lab to the production line where it can take constant measurements hour after hour and day after day have been clear to quality controllers and production managers for years.
Until recently however, the technology has failed to meet the challenge with filter-based near infrared technology unable to deliver the sort of savings hoped for.
All that has changed with the advent of new Diode Array based solutions teamed with strong calibrations and the latest computing technology.
One company already making good use of
the technology development is Spanish pre-mium flour suppliers Emilio Esteban.
With the help of an in-line, near infrared process monitoring solution called ProFoss from Foss, it is raising high quality standards to new levels while gaining more vision and insight into the milling process.
From laboratory to productionA flour production facility like the one at
the Emilio Esteban flour mill in Spain typically produces around 100 kilos of premium grade flour every minute.
That’s not a huge output by industry stand-ards, but plenty for the staff at the in-house laboratory to control as they strive to ensure that deliveries always match the high standards of discerning customers, including, amongst oth-ers, producers of baby food.
Company director Emilio Esteban sets out the business strategy in the current competitive business landscape.
“There are basically two options. Either you go for high capacity and compete on price or you invest in high quality.”
With a high quality strategy in mind, Esteban
and his staff have acquired a helping hand - or ‘eye’ to be more precise - in the form of the ProFoss.
Mounted directly in production at the final steps in the milling process, the ProFoss moni-tors the flour as it flows through pipes at up to 25 metres a second. This avoids the need for a bypass stream to collect samples. The instru-ment is housed in a practical and robust stainless steel cabinet (ATEX approved).
While it may not win any design awards, the wealth of information the ProFoss provides is something for any quality controller to get excited about.
The analyser automatically monitors mois-ture, protein and ash every few seconds and the regular results are fed back to a computer in the mill control room where they are displayed in a graphical form using Foss ISIscan software. The charts resemble a seismic graph. A nice straight line indicates that the flour composition is on target, but with a tremor indicated if something starts to go off track. This allows anyone work-ing in production to see at a glance whether everything is running to plan.
The new system does exactly the same job
Get in lineProcess analysis solutions open new opportunities for improved profit and qualityby Darren Robey, Foss, Denmark
12 | november - december 2011 Grain&feed millinG technoloGy
FEATURE
GFMT11.06.indd 12 30/11/2011 17:28
y Measure chemical composition as soon as you receive your raw materials. y Estimate technical values of flours, semolinas, grits, glutens, starches (and other powders products).y Moisture, protein, ash content, zeleny, hydration*. (* choose from over 60 calibrations available)
INFRANeO Junior can also analyse whole grains.
Look forthe NIR solution
that best matches your needs
INFRANeO JUNIOR
SIMPLe
ACCURATe
wITh NO OPeRATOR
INFLUeNCeCOST SAvINg
FAST
20, avenue Marcellin Berthelot • 92396 Villeneuve-la-Garenne • FRANCETél. : + 33 1 41 47 50 29 • Fax : + 33 1 41 21 07 10 • Mail : [email protected] • www.chopin.frPhoto credits : www.istockphoto.fr-© Elena Elisseeva-© Kristian Septimius Krogh-© Srdjan Stefanovic-© Dr. Heinz Linke-© Stratesigns, Inc.-© Kaupo Kikkas.
infraneo_junior_GB_190x132mm.indd 1 24/02/2011 14:24:49november - december 2011 | 13 Grain&feed millinG technoloGy
Döscher & Döscher supplies specialized solutions for an accurate and reliable moisture and density determination in the production process.
Our technology based on the 2-Parameter-Resonance-Technology, this makes it possible to control density and color independent of the moisture in your products.
Following Moisture Measuring Systems can be used in the feed production:
• MoistureScan - Continuous control of the moisture content in process
• MoistureScan XT - for high product temperature (<140°C), for example after the dryer
• MoistureScan Ex - completely suitable for Atex zone 20
Inline Moisture Determination
www.doescher.comVisit us at Victam [Hall 6; Stand E056]
Doescher_90x132mm.indd 1 29/03/2011 16:07
NIR-Online GmbH SAP Partnerport Altrottstraße 31D-69190 WalldorfTel.: +49 (0) 6227 732 660Fax: +49 (0) 6227 732 670Email: [email protected] www.nir-online.de
proven solutions for monitoring & control
Feed & Petfood • Intake qualifi cation & sorting• Mixing with controlled addition• Extruding & pelletizing conditioning• Final product qualifi cation
Best For Quality Control
...in real-time at lower costMake every batch inn speecc...
NIRonline_90x132_finalV2.indd 1 25.02.2011 14:19:22
GFMT11.06.indd 13 30/11/2011 17:28
Laboratory manager, Antonio Caballero conducted a study which indicates very similar performance for both instruments. And, of par-ticular importance is the fact that even though the performances of the two solutions are very similar, the frequency of measurement with the ProFoss system allows trends and irregularities to be spotted more quickly.
Other applications?While the benefits for flour production
are clearly demonstrated in the story above, it doesn’t take a great deal of lateral thinking to see the application of this technology in other parts of the grain and feed supply chain.
Thankfully the answer to this question is very much yes.
A similar story to the one above can be told in protein meal production where the instrument has demonstrated similar levels of benefit.
Likewise whole grain is an area where this technology can provide significant benefits to grain handlers. Whether it be at intake into the mill, on loading a bulk vessel or in the elevator conducting in stream segregation or blending, having real time inline analysis can have significant benefits over bench top techniques.
One novel use for in line analysis might well be fraud prevention.
Anyone handling grain has heard a story of someone delivering a load of grain who has taken it upon themselves to mix some poor grain, perhaps high moisture or low protein, in areas of the load where they know the sample spear won’t reach, while putting the good grain on top.
With inline analysis, such practices will soon be found as inline analysis takes sam-ples from a much higher proportion of the load as it passes through the elevator. Sure, once the product is in the plant or silo it is too late, but such monitoring combined with appropriate penalties will soon see those wanting to beat the system either stop the practice or at least divert their attention to the receiver who isn’t so alert.
The simple fact is that inline NIR is always alert and is constantly checking quality.
arriving at the lab, but these don’t represent the whole process. ProFoss is another concept – it is placed inline and provides constant and continuous information, so in case there is any problem, you can react immediately and that is the key.”
According to laboratory manager Antonio Caballero, the accuracy of ProFoss is equal to the Infratec when measuring protein, moisture and ash.
Besides this, with ProFoss, he believes that traceability has increased as the company now has a more comprehensive picture of quality.
“I believe that improved control of the process will increase qual-ity levels and give us a com-petitive edge,” says Caballero.
“We will also improve traceability, as we know exactly how the process is working. And overall, we will increase the quality of our products.”
An obvious consideration was whether the accuracy of measure-ments with the ProFoss would be comparable to the exist-ing desktop Infratec 1241 grain analyser used in the laboratory.
as the previous analysis instrument in the labora-tory, but now measurements are made several times a minute instead of every few hours. It is this frequency that helps to keep production right on target. It also reduces the risk of varia-tions in content of products when a new batch is started.
Esteban sums up the advantage of con-tinuous measurement and the difference in comparison to the Infratec 1241 Grain Analyser located in the laboratory.
“Infratec and ProFoss are completely differ-ent devices,” he says.
“The reason for this is where they are situated. Infratec allows you to analyse samples
14 | november - december 2011 Grain&feed millinG technoloGy
FEATURE
GFMT11.06.indd 14 30/11/2011 17:28 GFMT11.06.indd 15 30/11/2011 17:29
Grain&feed millinG technoloGy november - december 2011 | 3
®
Daniit A/S · Jyllandsgade 30 · DK-6400 SønderborgTel. +45 7342 3636 · www.daniit.com · [email protected]
Agro 3000 Flex plant control for feed plant:
■ Tailored design for · feed plants · petfood plants · fish feed plants
■ Modular design
■ Multi monitor support
■ Supports data integration to SAP, MS Dynamics, and others…
■ Energy saving
■ Remote control from iPad
■ Live business data and KPIs on iPad and iPhone – anywhere – anytime
■ 24/7 service and world wide support
■ More than 40 years in business
Visit us at Victam Asia 2012, stand C065
Invites you to our stand number
at
Bangkok International Trade & Exhibition Centre (BITEC)88 Bangna-Trad Road (Km.1), Bangna, Bangkok 10260, Thailand
Exhibition dates and opening timesWednesday 15th February 2012: 10.00 – 18.00Thursday 16th February 2012: 10.00 – 18.00
Friday 17th February 2012: 10.00 – 17.00
With our compliments
We look forward to greeting youSupported by
Thai Ministry of Agriculture & Co-Operatives,Thai Department of Livestock Development,
Thai Department of Fisheries, Thai Feed Mill Association,Thai Rice Milling Association, Thai Chamber of Commerce
Thailand Conference & Exhibition Bureau
invitation
Live business data and KPIs on iPad and iPhone – anywhere – anytime
Hygiene, Health and Safety
Wheat and the Screenroom
Mill Processes and Performance
Product Handling, Storage and Distribution
Flour
Power and Automation
Flour Milling Management
Course Fees 2011-12
The cost per module is: £310 (+ VAT at 20% where applicable)
includes postage, textbook and exam registration
nabim Members: £210 per module (a discount of £100)
Non-UK Companies: £260 per module (a discount of £50)
An indispensable tool for developing the knowledge and
competence of flour millers and their colleagues.
A clear presentation of the industry and process, in 7 modules.
Dedicated tutor support given to every student, providing
professional guidance throughout the course year.
To enrol or find out more, contact:
nabim 21 Arlington Street London SW1A 1RN UK Tel: +44 (0)20 7493 2521 Fax: +44 (0)20 7493 6785 email: [email protected] www.nabim.org.uk
Flour Milling Training Internationally recognised distance learning programme
Developed for millers by industry professionals
Studied every year by hundreds of millers worldwide
Seven Steps to Success
GFMT11.06.indd 3 30/11/2011 17:28
Innovations for a better world.
Antares MDDR-600.
Small Roller Mill for
High Requirements.
Compact dimension. Four-roller mill
with roll length of 600 mm
Sanitation. Top hygienic standards for
food safety.
Outstanding precision. Ultra-precise
settings, consistent flour.
Perfect grinding. Powerful roll pack,
highly consistent grinding.
Ultimate design. The perfect combina-
tion of ergonomics and performance.
Perfection in grain milling – a highly demanding task. Antares sets new standards
for round-the-clock milling. The self-contained roll pack and reliable product
feed ensure precise and consistent flour. Maximum hygiene is guaranteed thanks
to clever insulation, integrated product inlet aspiration and stainless steel lining.
Experience a new level of ease of use and quality from ergonomic controls
and operating reliability to the highly impressive design. Antares – The New Art
of Milling.
Bühler AG, Grain Milling, CH-9240 Uzwil, Switzerland, T +41 71 955 11 11, F +41 71 955 66 11 [email protected], www.buhlergroup.com
BUH_GM_Inserat_Antares_2011_A4.indd 1 07.04.2011 15:34:28GFMT11.06.indd 54 30/11/2011 17:31
PREVIOUS PAGEwww.gfmt.co.uk
LINKS• Seethefullissue• VisittheGFMTwebsite
• ContacttheGFMTTeam
• SubscribetoGFMT
A subscription magazine for the global flour & feed milling industries - first published in 1891
In this issue:
• Mycotoxins an overview
• Database for animal diet formulation techniques: A glance to last decade
• Food safetyin the grain milling industry
• Recent advances in rapid grain testing
November - December 2011
• African advances
Animal feed milling is one of the most buoyant activities in the agri related field
• Optical sorting Optical sorting has come of
age and should be considered as a serious option for inclusion in any modern wheat cleaning plant
• Get in lineProcess analysis solutions open new opportunities for improved profit and quality
GFMT11.06.indd 1 30/11/2011 17:28
ThisdigitalRe-printispartoftheNovember|December2011editionofGrain&FeedMillingTechnologymagazine.Contentfromthemagazineisavailabletoviewfree-of-charge,bothasafullonlinemagazineonourwebsite,andasanarchiveofindividualfeaturesonthedocstocwebsite.Pleaseclickheretoviewourotherpublicationsonwww.docstoc.com.
Topurchaseapapercopyofthemagazine,ortosubscribetothepapereditionpleasecontactourCirculationandSubscriptionsManageronthelinkadove.
INFORMATIONFORADVERTISERS-CLICKHERE
Article reprintsAll Grain & Feed Milling Tecchnology feature articles can be re-printed as a 4 or 8 page booklets (these have been used as point of sale materials, promotional materials for shows and exhibitions etc).
If you are interested in getting this article re-printed please contact the GFMT team for more information on - Tel: +44 1242 267707 - Email: [email protected] or visit www.gfmt.co.uk/reprints