ge optimal sheet steel cabinets030-069
TRANSCRIPT
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
1/40
30
Sheetsteelfloor
sta
nding
enclosures
GE Power Controls
OPTIMAL FS
Construction
Frame
1.75 mm painted steel.
Seamwelded reversed open profiles with 25 mm hole
pattern according to DIN 43660. Including integrated
external hole pattern.
Door
2.0 mm painted steel.
Surface mounted with hinges allowing left or right hand
opening. Including door frame with 25 mm hole pattern.
Rear panel1.5 mm painted steel.
Fitted by M6 torx screws.
Standard facilities for rear door mounting.
Side panels
1.5 mm painted steel.
Supplied as an accessory.
Roof panel
1.5 mm painted steel.
Removable.
Bottom plates
1.5 mm galvanised steel.
Consists of three pieces.
Lock
Espagnolet 4-point locking system. Does not interfere with
the enclosure inner space. Standard 3 mm double bit lock.
Can be exchanged for standard inserts or Euro-cylinder,
swing handle or digital locking system.
Mounting plate
3 mm galvanised steel.
Double folded and slides into position. Adjustable in depth
by steps of 25 mm. Attached on the outside of the enclo-
sure carton.
Earthing
All panels are earthed through their fittings and are
equipped with a separate earthing stud.
Colour
RAL 7032 polyester powder structure paint.
Modular versionsingle door
Protection degree
IP56 / NEMA 4, 12, 13.
Approvals
Standard delivery
- Frame with fitted door, rear
panel, roof panel, bottom plates*,
mounting plate* and door frame*.
- Earthing bolts.
- Delivered on a pallet with width
identical with the enclosure to
allow suiting without removal.
- All packing material recyclable.
*not included for 400 wide cable
enclosures.
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
2/40
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
3/40
32
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
W-65
W-90 D-90
D-65
W-106
2
4.5
H-106
12
59.5
Top view
W = 400-1000
max.D-41
D+12
H-18
H+3.5
D-37
D-90
Sectional side view
Mountingplate
W-69
W-1
Front view
W-145
Door = W-7
W-90
20
W-148.5
W-168
D-125
W-125
W-125
Sectional topview (without bottomplates)
W = 400-1000
Sideview
4
25
H-65
H-90
D-65
22
22
W-31
15.3
M12
D-69
H-170
Vertical profile
12.5
44.2
12.5
22
26
10
17
26.5
35
46
25
4.34.69
7.5
10
14
OPTIMAL FS - Modular version, single door - Dimensional drawings
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
4/40
33
OPTIMALFS
OPTIMAL FS
Construction
Frame
1.75 mm painted steel.
Seamwelded reversed open profiles with 25 mm hole pat-
tern according to DIN 43660. Including integrated external
hole pattern.
Doors
2.0 mm painted steel.
Surface mounted with four hinges. Including door frame
with 25 mm hole pattern. Doors can not be reversed.
Separate doors to be ordered for left hand door locking.Rear panel
1.5 mm painted steel.
Fitted by M6 torx screws. Standard facilities for rear door
mounting. Split rear panels in 1600 wide enclosures.
Side panels
1.5 mm painted steel.
Supplied as an accessory.
Roof panel
1.5 mm painted steel.
Removable.
Bottom plates
1.5 mm galvanised steel.
Consists of three pieces.
Lock
Espagnolet 4-point locking system. Does not interfere with
the enclosure inner space. Standard 3 mm double bit lock.
Can be exchanged for standard inserts or Euro-cylinder,
swing handle or digital locking system.
Mounting plate
3 mm galvanised steel.
Double folded and adjustable in depth by steps of 25 mm.
Attached on the outside of the enclosure carton.
Earthing
All panels are earthed through their fittings and are
equipped with a separate earthing stud.
Finish
RAL 7032 polyester structure powder paint.
Modular versiondouble door
Protection degree
IP55 / NEMA 12, 13.
Approvals
Standard delivery
- Frame with fitted doors, rear
panel, roof panel, bottom plates,
mounting plate and door frame.
- Delivery also includes earthing
bolts.
- Delivered on a pallet with width
identical with the enclosure to
allow suiting without removal.
- All packing material recyclable.
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
5/40
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
6/40
35
OPTIMALFS
max.D-41
D+12
H-18
H+3.5
D-37
D-90
Sectional side view
W-69
W-1
Front view
Door = W/2 - 2
Top view W = 800-1200
D-125
W-125
Door = W/2 - 9
491
510.5
Sectional topview (without bottomplates) W = 800-1200
Sideview
W/2-145
W/2-125
H-170
H-150
66
H-65
H-90
D-65
W-31
W-106
24.5
H-106
12
59.5Mountingplate
22
22
W-168
W-148.5
W-65
W-90D
-90
D-65
Only W=1200
25
4
20
15.3
M12
D-69
Vertical profile
12.5
44.2
12.5
22
26
10
17
26.5
35
46
25
4.34.69
7.5
10
14
OPTIMAL FS - Modular version, double door - Dimensional drawings
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
7/40
36
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
Construction
Body
1.5 mm painted steel.
Four times folded and seam-welded frame.
Integrated double row hole pattern.
Door
2.0 mm painted steel.
Surface mounted with hinges allowing left or right hand
opening. Including door frame with 25 mm hole pattern.
Rear panel
1.5 mm painted steel.Fitted by M6 torx screws.
Standard facilities for rear door mounting.
Roof panel
1.5 mm painted steel.
Removable.
Bottom plates
1.5 mm galvanised steel.
Consists of three pieces.
Mounting plate
3 mm galvanised steel.
Double folded and slides into position. Adjustable in depth
by steps of 25 mm. Attached on the outside of the
enclosure carton.
Lock
Espagnolet 4-point locking system. Does not interfere with
the enclosure inner space. Standard 3 mm double bit lock.
Can be exchanged for standard inserts or Euro-cylinder,
swing handle or digital locking system.
Earthing
All panels are earthed through their fittings and are
equipped with a separate earthing stud.
Finish
RAL 7032 polyester structure powder paint.
Mono versionsingle door
Protection degree
IP66 / NEMA 4, 12, 13.
To achieve IP66, use gasket kit
821529 when fitting the bottom
plate.
Approvals
Standard delivery
- Body with fitted door, rear panel,
roof panel, bottom plates, mount-
ing plate and door frame.
- Delivery also includes earthing
bolts.
- Delivered on a pallet with width
identical with the enclosure to
allow suiting without removal.
- All packing material recyclable.
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
8/40
37
OPTIMALFS
IP66 IP66
Enclosures withmounting plate
Enclosures withoutmounting plate
H x W x D
Height 16001600 x 600 x 4001600 x 800 x 4001600 x 1000 x 400
Height 18001800 x 600 x 4001800 x 800 x 4001800 x 1000 x 400
Height 20002000 x 600 x 4002000 x 800 x 4002000 x 1000 x 400
821291821292821293
821294821295821296
821297821298821299
821300821301821302
821303821304821305
821306821307821308
OPTIMAL FS - Mono version, single door
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
9/40
38
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
W-65
W-903
10
335
Top view
W = 600-1000
max 359
331
412
H-18
H+3.5
363
310
Sectional side view Mountingplate
W-69
Front view
W-145
Door = W-7
W-90
20
W-148.5
W-168
275
W-125
W-125
Sectional topview (without bottomplates)
W = 600-1000
4
25
W
W-106
24.5
H-106
1259.5
22
22
H-65
H-90
335
M12
15.3
H-170
OPTIMAL FS - Mono version, single door - Dimensional drawings
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
10/40
39
OPTIMALFS
OPTIMAL FS
Construction
Body
1. 5 mm painted steel.
Four times folded and seam-welded frame. Integrated dou-
ble row hole pattern. Separate doors to be ordered for left
hand door locking.
Doors
2.0 mm painted steel.
Surface mounted with four hinges. Including door frame
with 25 mm hole pattern. Doors can not be reversed.
Separate doors to be ordered left or right hinged.Rear panel
1. 5 mm painted steel.
Fitted by M6 torx screws. Standard facilities for rear door
mounting. Split rear panels on 1600 wide enclosures.
Roof panel
1. 5 mm painted steel.
Removable.
Bottom plates
1.5 mm galvanised steel. Consists of three pieces.
Lock
External espagnolet 4-point locking system.
Standard fitted 3 mm double bit lock. Can be exchanged
for standard inserts or Euro-cylinder and swing handle.
Mounting plate
3 mm galvanised steel.
Double folded and adjustable in depth by steps of 25 mm.
Attached on the outside of the enclosure carton.
Earthing
All panels are earthed through their fittings and are
equipped with a separate earthing stud.
Finish
RAL 7032 polyester structure powder paint.
Mono versiondouble door
Protection degree
IP55 / NEMA 12, 13.
Approvals
Standard delivery
- Body with fitted door, rear panel,
roof panel, bottom plates, mount-
ing plate and door frame.
- Delivery also includes earthing
bolts.
- Delivered on a pallet with width
identical with the enclosure to
allow suiting without removal.
- All packing material recyclable.
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
11/40
40
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
IP55 IP55
Enclosures withmounting plate
Enclosures withoutmounting plate
H x W x D
Height 16001600 x 1200 x 400
Height 18001800 x 1200 x 4001800 x 600 x 400
Height 20002000 x 1200 x 4002000 x 1600 x 400
821309
821310821311
821312821313
821314
821315821316
821317821318
OPTIMAL FS - Mono version, double door
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
12/40
41
OPTIMALFS
max 359
331
412
H-18
H+3.5
363
310
Sectional side view
Mountingplate
W-69
Front view
Door = W/2 - 2
Top view W = 1200
275
1075
Door = W/2 - 9
491
510.5
Sectional topview (without bottomplates) W = 1200
W/2-145
W/2-125
H-170
Sectional topview (without bottomplates) W = 1600
W
H-150
66
632
651.5
710
735
W-106
2
4.5
H-106
12
59.5
22
22
H-65
H-90
335
675 675
M12
15.3
25
20
4
31
0
33
5
1032
1051.5
M12
1110
1135
1510
1535
OPTIMAL FS - Mono version, double door - Dimensional drawings
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
13/40
42
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
Construction
Frame
1,75 mm steel plate.
Seamwelded reversed open profiles with 25 mm hole
pattern according to DIN 43660. Including integrated
external hole pattern.
Rear door
2 mm steel plate
Surface mounted with hinges allowing left or right hand
opening. Including door frame with 25 mm hole pattern.
Side panelsSupplied as an accessory.
Roof panel
1.5 mm steel plate.
Removable.
Bottom plates
1.5 mm galvanised steel. Consists of three pieces.
Lock
Espagnolet 4-point locking. Standard 3 mm double bit lock.
Can be exchanged for standard inserts or Euro-cylinder
and swing handle.
19 profiles
Zinc plated
Provide front and side universal punchings. Zinc plated.
Earthing
All panels are earthed through their fittings and are
equipped with a separate earthing stud.
Finish
Frame and roof plates: grey RAL 7032 structure powder
paint.
Industrial data enclosure
Protection degree
IP56 / NEMA 4, 12, 13 when front
door and side panels are fitted
Approvals
Standard delivery
- Frame with fitted rear door, roof
panel, bottom plates, 19 profiles
at front and fixing brackets.
- Delivery also includes earthing
bolts.
- Delivered on a pallet with width
identical with the enclosure to
allow combining without removal.
- All packing material recyclable.
Low resolution
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
14/40
43
OPTIMALFS
IP56
Enclosures
H x W x D
Height 11001100 x 600 x 600
Height 14001400 x 800 x 600
Height 16001600 x 600 x 600
Height 18001800 x 600 x 600
Height 20002000 x 600 x 6002000 x 600 x 8002000 x 800 x 6002000 x 800 x 800
Height 22002200 x 600 x 6002200 x 600 x 8002200 x 800 x 6002200 x 800 x 8002200 x 800 x 900
821319
821320
821321
821322
821323821324821325821326
821327821328821329821330821331
OPTIMAL FS - Industrial data enclosure
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
15/40
44
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
535
510
D-90
D-65
Top view
W = 600
Sectional side view
531
599
Front view
W = 600
451.5
432
Sectional topview (without bottomplates)
W = 600
569
D-69
H-18
H
+3.5
D-90
D-65
735
710
D-90
D-65
Top view
W = 800
731
799
Front view
W = 800
651.5
632
Sectional topview (without bottomplates)
W = 800
769
451
465
451
465
L(..
U)
L(..
U)
L A U
1303 13.3 29
1503 24.4 33
1703 13.3 38
1903 24.4 42
ID(H)
1400
1600
1800
2000
2103 13.3 472200
1003 18.9 221100
54
51
Minimum distance to
inside door.
Minimum distance to
outside frame.
54
51
*
* ** * **
**
H-65
H-90
D
"19 profile
29
14.5
27
14.5
18
7
7
A
15.8
75
44.4
5
31.7
5
9.5
7
OPTIMAL FS - Industrial data enclosure - Dimensional drawings
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
16/40
45
OPTIMALFS
OPTIMAL FS
Construction
Frame
1.75 mm painted steel. Seam welded reversed open pro-
files with 25 mm hole pattern according to DIN 43660.
Including integrated external hole pattern.
Monitor shelf
Fully adjustable in height with newly developed rapid
adjustment system
Front door
2.0 mm painted steel.
Surface mounted with concealed hinges.Monitor door
Fitted with design strip in brown (RAL 7015) which allows cus-
tomisation. Viewing area 375 x 455 mm for monitor 14-21.
Keyboard tray
Hinged, with mouse pad (RH or LH). Painted in a two tone
colour grey/brown. Max. keyboard width 470 mm.
Rear door
2.0 mm painted steel. Surface mounted with hinges allow-
ing left or right hand opening.
Side panels
1.5 mm painted steel
Removable, fixed on the outside hole pattern of the frame
for easy and rapid mounting. Access to the fixing screws is
denied when the doors are closed.
Roof panel
1.5 mm painted steel
Removable and fixed from the inside.
Bottom plates
1.5 mm galvanised steel
Consists of three pieces for 600 mm deep and four pieces
for 800 mm deep.
Lock
Espagnolet two or four pount locking system. Does not
interfere with the enclosure inner space. Standard 3 mm
double bit lock. Can be exchanged for standard inserts or
Euro-cylinder or swing handle. Monitor door and key board
tray are fitted with key lock.Earthing
All panels are earthed through their fittings and are
equipped with a serparate earthing stud.
Finish
Grey RAL 7035 polyester powder structure paint in combi-
nation with brown RAL 7015.
Two Tone industrial computer enclosure
Description
Multi purpose computer enclosure
with aesthetic design and attractive
colour scheme. Supplied in a two
tone structured paint finish, grey
(RAL 7035) and brown (RAL 7015)
makes it suitable for both office
and factory environments.
Protection degreeIP54 / NEMA 1 & 12
Approvals
Standard delivery
- Frame with fitted plane and
glazed doors, hinged keyboard
tray, mouse pad, monitor shelf,
roof panel, bottom plates, side
panels and fixing devices.- Delivery also includes earthing
bolts.
- Delivered on a pallet with width
identical with the enclosure to
allow suiting without removal.
- All packing material is recyclable.
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
17/40
46
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
IP54
Enclosures
H x W x D
Height 16001600 x 600 x 6001600 x 600 x 800
821332821333
OPTIMAL FS - Industrial computer enclosure
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
18/40
47
OPTIMALFS
455
375
1603.5
851
250
1346.5
D+12
15.3
232
907
*1101
* Standard position, adjustable in height.
OPTIMAL FS - Industrial computer enclosure - Dimensional drawings
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
19/40
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
20/40
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
21/40
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
22/40
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
23/40
52
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
Accessories
Side panels
Easy one man assembly. Sealed by an
extruded, one piece polyurethane gasket
and mounted with 8 screws.
Can be replaced by the side door.IP56 / NEMA4, 12, 13.
Material: 1.5 mm steel plate.
Finish: structure powder paint, RAL 7032
|821334 2
|821335 2
|821336 2
|821337 2
|821338 2
|821339 2
|821340 2
|821341 2
|
821342 2
|821343 2
|821344 2
|821345 2
|821346 2
Clip-on cage nuts
|821347 50
M6 - for fixing side panels.
Countersunk screws
|821348 250
Torx countersunk screws M6 x 16
Plinths, front/rear
Front and rear plinth sections.
For cabling without any restrictions and in
accordance with the VDE 0113 standard.
The plinth consists of four corner pieceswith removable front covers. The plinth side
panels are to be ordered separately (p. 53).
Produced in 100 mm and 200 mm heights.
200 mm high plinths are delivered with a
rear cover for cabling that consists of two
removable panels 100mm high. The front
cover is a one piece panel of 200 mm high.
All panels have double returns on each
panel.
Materials: corner pieces in 2,5mm zinc
plated steel, panels in 2 mm steel plate.
Finish: structure powder paint, RAL7022
Pack quantity: 1 set of 4 corner pieces inclu-
ding covers, 1 front and 1 rear panel
(2 rear panels for 200mm high plinths) with
mounting material for side panels and
transversal profiles.
|821349 1
|821351 1
|821352 1
|821353 1
|821354 1
|821355 1
|
821357 1
|821358 1
|821360 1
|821361 1
|821363 1
|821364 1
|821365 1
H D
1100 600
1400 600
1600 600
1800 400
1800 500
1800 600
2000 400
2000 500
2000 600
2000 800
2200 600
2200 800
2200 900
H W
100 400
100 600
100 700
100 800
100 1000
100 1200
100 1400
200 400
200 600
200 800
200 1000
200 1200
200 1400
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
24/40
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
25/40
54
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
Accessories
Mounting plates
Standard mounting plate. Fixing bracket kit
821419 to be ordered separately. Can also
be mounted in the side of an enclosure by
using bracket kit 821415 or slided in by theside by using the sliding profile (p. 56).
Material: 3 mm galvanised steel.
|821395 1
|821396 1
|821397 1
|821398 1
|821399 1
|821400 1
|821401 1
|
821402 1
|821403 1
|821404 1
|821405 1
|821406 1
|821407 1
|821408 1
|821409 1
|821410 1
|821411 1
|821412 1
Mounting plate fixing brackets
|821414 2
For extra fixing of the mounting plate in the
middle in addition to the normal fixing top
and bottom.
Mounting plate adjustment brackets
|821413 2
With these brackets the mounting plate canbe adjusted in depth by steps of 25 mm in
the enclosure frame
Material: 3 mm zinc plated steel
Side mounting plate brackets
|821415 4
To mount the standard mounting plate in the
side of the enclosure frame.
Provides a flat mounting surface with theprofiles.
Material: 3 mm galvanised steel.
Union mounting plates
Covers the space between pairs of adjacent
mounting plates to provide a continuous
working surface, when two enclosures are
mounted together.
Material: 2 mm galvanised steel.
|821416 1
|821417 1
|821418 1
Mounting plate brackets
|821419 1
To fix mounting plates to the furthest posi-
tion in the rear of the enclosure, including
adjustment brackets for depth adjustment in
steps of 25 mm. Brackets are needed when
an extra mounting plate is required.
Material: 3 mm zinc plated steel.
Pack quantity: 2 top brackets and 2 bottom
sliding brackets, 2 adjustment brackets with
mounting material.
Wide mounting plate
To be mounted on sliding profiles (p. 56).
Nominal width equals the enclosure width.
Material: 3 mm galvanised steel.
|821432 1
|821433 1
| 821434 1
|821435 1
H W h w
1600 600 1494 494
1600 800 1494 694
1600 1000 1494 894
1600 1200 1494 1094
1800 600 1694 494
1800 800 1694 694
1800 500 1694 394
1800 1000 1694 894
1800 1200 1694 1094
2000 500 1894 394
2000 600 1894 494
2000 800 1894 694
2000 1000 1894 894
2000 1200 1894 1094
2200 600 2094 494
2200 800 2094 694
2200 1000 2094 894
2200 1200 2094 1094
H = 1800
H = 2000
H = 2200
H W
2000 600
2000 800
2000 1000 2000 1200
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
26/40
55
OPTIMALFS
Accessories
Partial mounting plates
Can be mounted in any height or depth
position within the 25 mm hole pattern.
Appropriate sizes can also be used in the
sides of the enclosure by using thecorresponding depth profiles.
For more mounting levels and easy
exchange of defective components.
Material: 3 mm galvanized steel.
|821420 1
|821421 1
|821422 1
|821423 1
|821424 1
|821425 1
|
821426 1
|821427 1
|821428 1
|821429 1
|821430 1
|821431 1
Telequick mounting plate
Simplifies installation and equipment fitting.
Rectangular holes 26 x 11mm to obtain
required fixing positions with snap-nuts.
The nuts can be moved around within the
rectangular hole.
Material: 2 mm galvanised steel plate.
|821460 1
|821461 1
|821462 1
|821463 1
|821464 1
|821465 1
Click-in profile
Can be used in width and depth directly
onto the enclosure profile or in combination
with the universal mounting profile. They
have double bended returns for more rigidity
and three rows of hole patterns (in the front)
for cage nut fixing and self tapping screws.
Material: 1.5 mm zinc plated steel.
|821436 4
|821437 4
|821438 4
|821439 4
|821440 4
|821441 4
Universal mounting profile
|821442 4
|821443 4
|821444 4
| 821445 4
|821446 4
|821447 4
|821448 4
|821449 4
|821450 4
|821451 4
40 mm wide and 25 mm high profile, which
can be mounted in all directions in the
enclosure frame. Four profiles with moun-
ting material are packed in one package.
Can be used in combination with the click-in
profile. The profiles when mounted onto the
enclosure frame are flush with the enclosure
profiles.
Two rows of hole patterns for cage nut fixing
and self tapping screws are foreseen.
Material: zinc plated steel
Vertical dividing profile
Fitted in the centre of 1200 or 1600 mm
wide enclosures to give standard mounting
facilities of a 600 or 800 mm wide
enclosure. This enables separate fitting of
equipment such as swing frames, system
profiles etc., in either side of the enclosure.
Adjustable in depth within the 25 mm hole
pattern.
Material: 2 mm zinc plated steel.
|821466 2
|821467 2
|821468 2
|821469 2
Vertical depth dividing profile
|821470 2
|821471 2
|821472 2
|821473 2
In combination with the vertical dividing pro-
file there is a full separation of the enclosure
into two stand-alone enclosures within one
frame. Can be used in combination with the
click-in profile and the universal mounting
profile.
Material: zinc plated steel.
For enclosure
H/W W/H h/w w/h
400 400 294 294
400 500 294 394
600 400 494 294
600 500 494 394
600 800 494 694
600 1000 494 894
800 400 694 294
800 800 694 694
1000 400 894 294
1000 800 894 694
1200 400 1094 294
1200 600 1094 494
For enclosure
H W
500 400
600 400
600 500
600 600
800 600
1000 800
For enclosure
W/D w/d
400 335
500 435
600 535
800 735
1000 935
1200 1135
L = 400
L = 500
L = 600
L = 800L = 1000
L = 1200
L = 1600
L = 1800
L = 2000
L = 2200
For enclosure
H = 1600
H = 1800
H = 2000
H = 2200
For enclosure
D = 400
D = 500
D = 600
D = 800
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
27/40
56
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
Accessories
Fixing brackets
|821474 4
|821475 4
Use 821474 fixing brackets for mounting
vertical (depth) dividing profiles into1200 mm wide enclosures.
Use 821475 fixing brackets for mounting
vertical (depth) dividing profiles into
1600 mm wide enclosures.
Material: zinc plated steel.
Transversal sliding profile
To be used when installing a wide or
standard mounting plate.
Adjustable in depth in steps of 25 mm.
Material: 2 mm galvanised steel.
|821452 2
|821453 2
|821454 2
|821455 2
Height profiles
Vertical profiles with 25mm hole pattern, to
support DIN rails and appropriate telequick
mounting plates. Adjustable in depth in
steps of 25 mm.
Material: 2 mm zinc plated steel.
|821476 2
|821477 2
| 821478 2
|821479 2
Snap nuts for telequick plates
|821480 100
M4
|821481 100
M5
|821482 100
M6
For enclosure
W = 600
W = 800
W = 1000
W = 1200
For enclosure
H = 1600
H = 1800
H = 2000H = 2200
External coupling brackets
|821485 6
Brackets mounted on the outside hole pat-
tern of the frame, ensuring a strong and 3
dimensional alignment of the coupled enclo-sures with auto spacer function. This
method of coupling enclosures has also the
advantage of realising a direct earthing con-
nection between the enclosure frames.
Material: 3 mm zinc plated steel.
Internal corner coupling kit
|821487 4
For extra support when coupled enclosures
are fully equipped and require heavy duty
lifting.
Material: 3 mm zinc plated steel.
Internal coupling brackets
|821486 6
Brackets provide a rigid reinforcement of the
enclosure assembly.
Automatic spacing between the enclosures
is ensured.
Material: 3 mm zinc plated steel.
Corner coupling kit
|
821488 1 set
The enclosures can be coupled together
side to front or side to side.
The IP rating is hereby secured
Material: 1.5mm steel plate
Finish: structure powder paint RAL 7032.
Depth coupling kit
For coupling enclosures rear to rear.
Material: profiles in 2 mm and covers in
1.5 mm steel plate.
Protection: IP55
Finish: structure powder paint RAL 7032
|821489 1
|821490 1
|821491 1
For enclosure
H = 1600
H = 1800
H = 2000
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
28/40
Lifting eye bolts
|821493 2
M12 thread. Complies with
DIN 580 lifting requirements.
Wall fixing brackets
|821492 2
To fix the enclosure to the wall by using the
M12 screws on the top.
Prevents the enclosure from tipping over
e.g. on board of ships.
(Available on request.)
Lifting device
|821494 4
For optimal weight distribution when lifting
coupled enclosures.
To be used in combination with internal
corner coupling brackets.
Material: 5 mm zinc plated steel.
Cage nuts
|
821495 50
Cage nuts M6 designed for universal use on
the enclosure frame profiles and the profile
system.
Screws for clip-on cage nuts
|821496 250
Socket head screws M6x12 for clip-on
cage nuts
57
OPTIMALFS
Accessories
Countersunk screws
|821497 250
Torx extrudetite countersunk screws
M6 x 12
Extrudetite screws
Torx extrudetite screws for the fitting of
accessories, click in profiles, earthing etc.
|821498 250
M5
|821499 250
M6
Side mounting bar
For fixing cables, cable guides, etc. in the
side or the width of an enclosure.
Material: 2 mm zinc plated steel
|821500 10
|821501 10
|821502 10
|
821503 10
Carrier bars
Used for heavy units, such as transformers,
fitted in the bottom of the enclosure.
Material: 3 mm zinc plated steel.
|821504 2
|821505 2
|821506 2
|821507 2
For enclosureW/D = 400
W/D = 500
W/D = 600
W/D = 800
For enclosure
W/D = 400
W/D = 500
W/D = 600
W/D = 800
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
29/40
58
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
Accessories
Cable fixing bar
Mounted above the bottom plates.
Holds standard cable clamps to secure
incoming cables. Fully adjustable in depth.
Material: 2 mm zinc plated steel.
|821508 2
|821509 2
|821510 2
|821511 2
|821512 2
Cable fixing bar
Suspended below the bottom plates thereby
maximising the full usable space in the
enclosure. Holds standard cable clamps to
secure incoming cables.
Fully adjustable in depth.
Material: 2 mm zinc plated steel with plastic
counter parts.
|821513 2
|821514 2
|821515 2
|821516 2
|821517 4
Cable clamps
To secure incoming cables onto the cable
fixing bars. Holds the cable in position and
supports the weight.
Material: zinc plated steel.
|821518 25
|821519 25
|821520 25
|821521 25
|821522 25
|821523 25
|821524 25
|821525 25
|821526 25
|821527 25
|821528 25
For enclosure
W = 400
W = 600
W = 800
W = 1000
W = 1200
For enclosure
W = 400
W = 600
W = 800
W = 1000
W = 1200
Size
06-12 mm
10-14 mm
12-16 mm
14-18 mm
18-22 mm
22-26 mm
26-30 mm
30-34 mm
34-38 mm
38-42 mm
56-64 mm
Cable entry foam and bottom plate
gasket
|821529 1
The bottom of the enclosure is sealed by the
use of an adhesive gasket applied on to theframe around the bottom openings.
The cables are sealed by the addition of
adhesive foam placed between the bottom
plates. The elasticity and the size of this foam
assure a tight seal around most cables.
Pack: 1.6 m adhesive foam (30 x 25 mm)
and 6 m adhesive gasket (4.5 x 8 mm).
EMC cable entry and
bottom plate gasket
|821530 1
The bottom of the enclosure is sealed by
the use of an adhesive gasket applied to the
frame around the bottom opening.
The cables are sealed by the addition of
adhesive foam placed between the bottom
plates. The elasticity and the size of this foam
assure a tight seal around most cables.
Pack: 1.6 m adhesive EMC gasket for cable
entry and 6 m adhesive bottom plate gasket.
Earthing cable
For earthing or potential compensation
between units.
Material: 6 mm2 copper wire (yellow-green).
|821533 10
L = 220 - M8 x M6
|821534 10
L = 300 - M8 x M8
Earthing connection set for panels
Earth connection for the fixing of the ear-
thing straps & cables to panels, mounting
plates or profiles.
|821537 10
M6
|821538 10
M8
Earthing connections for frame
Earthing connections for the fixing of the
earthing straps & cables to the enclosure
frame.
|821531 10
M6
|821532 10
M8
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
30/40
59
OPTIMALFS
Accessories
Glazed door
Standard door with fitted clear safety glass
to view the inside of the enclosure.
Equipped with 3 mm double bit locking
system and door frame. Allows all options ofthe locking program. Use hinge kit if not for
replacement of standard door
Protection: IP55.
Material: frame 2mm steel plate.
Viewing area: 4 mm clear safety glass.
Finish: structure powder paint, RAL 7032
| 821559 1
|821560 1
|821561 1
|821562 1
|821563 1
|821564 1
|821565 1
|821566 1
|821567 1
Glazed door
Standard door with fitted smoked safety
glass to view the inside of the enclosure.
Equipped with 3 mm double bit locking
system and door frame. Allows all options of
the locking program. Use hinge kit if not for
replacement of standard door.
Protection: IP55.
Material: 2mm steel plate.
Viewing area: 4 mm smoked safety glass.
Finish: structure powder paint, RAL 7032
|821568 1
|821569 1
|821570 1
|821571 1
|821572 1
|821573 1
|821574 1
|821575 1
|821576 1
Earthing strap
For earthing or potential compensation bet-
ween panels and enclosure frame.
Material: Tinned electrolytic copper wire with
solder connection points - L = 300 mm.
|821535 10
Cross sectional area = 16 mm2
holes = 8.5 mm - strap width = 15 mm
|821536 10
Cross sectional area = 25 mm2
holes = 10.5 mm - strap width = 23 mm
Plain door
Standard door equipped with 3 mm double
bit locking system and door frame.
Door mounting kit (hinges, rod catchers) to
be ordered separately.
Allows all the options of the locking program
and 180 hinges.
Material: 2 mm steel plate
Finish: structure powder paint, RAL 7032.
|821539 1
|821540 1
|821541 1
|821542 1
|821543 1
|821544 1
|821545 1
|821557 1
|821558 1
H W
1100 600
1400 800
1600 600
1800 600
1800 800
2000 600
2000 800
2200 600
2200 800
H x W h x w
1100 x 600 876 x 415
1400 x 800 1176 x 615
1600 x 600 1376 x 415
1800 x 600 1576 x 415
1800 x 800 1576 x 615
2000 x 600 1776 x 415
2000 x 800 1776 x 615
2200 x 600 1976 x 415
2200 x 800 1976 x 615
H x W h x w
1100 x 600 876 x 415
1400 x 800 1176 x 615
1600 x 600 1376 x 415
1800 x 600 1576 x 415
1800 x 800 1576 x 615
2000 x 600 1776 x 415
2000 x 800 1776 x 615
2200 x 600 1976 x 415
2200 x 800 1976 x 615
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
31/40
60
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
Accessories
Door switch
|821577 1
Activates any electrical device (lighting,
coolers, etc.). Can be fitted after installing
the enclosure thereby keeping the dooropening free. Fixed (without screws) on the
inside hole pattern of the enclosure frame.
Cable entry M 20, UL-CSAapproved.
Switching load 6A-230V.
Door switch leads
|821578 5
Door switch connecting cable.
Partial door for monitor
For monitor size 14-17 or 19-21. Used in
combination with the hinged keyboard tray
821602, allows the installation of a PC.
The remaining space will be filled with top
and bottom panels and partial doors
Protection: IP55
Material: 2 mm steel plate.
Finish: structure powder paint RAL 7032,
with hardened glass.
|821579 1
|821580 1
Hinged keyboard tray
Horizontal hinged keyboard tray with lateral
(L.H. or R.H.) sliding mouse pad. Equipped
with panel stay. When tray folded out, the
enclosure is sealed for dust ingress by a
closed chamber.Material: 2 mm steel plate
Finish: structure powder paint RAL7032
|821602 1
H x W = 300 x 600
Partial doors
To divide the enclosure front into sections
when used in conjunction with the horizontal
divider. Equipped with 3 mm double bit lock
(1 lock up to 400 mm, over 400mm height2 locks).
Protection: IP55
Material: 2 mm steel plate.
Finish: structure powder paint, RAL 7032.
Hinges, locks and mounting material
included.
|821581 1
|821582 1
|821583 1
|821584 1
| 821585 1
|821586 1
|821587 1
|821588 1
|821589 1
|821590 1
|821591 1
|821592 1
|821593 1
|821594 1
|821595 1
|821596 1
|
821597 1
|821598 1
Top and bottom panels
Required to cover the remaining space at
the top and bottom. Height top = 70 mm,
height bottom = 100 mm.
Used in combination with the partial doors
and dividers.
Protection: IP55
For IP21 delivered without gasket.
Material: 2 mm steel plate
Finish: structure powder paint RAL 7032
|821599 2
W = 400
|821600 2
W = 600
|821601 2
W = 800
Viewing area No. of H W h w locks
500 600 285 375 2
600 600 285 375 2
H x W
150 x 400
150 x 600
200 x 400
200 x 600
250 x 400
250 x 600
300 x 400
300 x 600
400 x 400
400 x 600
400 x 800
500 x 400
500 x 600
600 x 400
600 x 600
600 x 800
800 x 600
1000 x 600
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
32/40
61
OPTIMALFS
Accessories
Horizontal divider
Modular enlosures
Used when the enclosure requires separa-
tion by partial doors or panels. Can be
mounted on the outside hole pattern of theopen frames (Modular versions).
Material: 2 mm zinc plated steel.
|821603 4
|821604 4
|821605 4
Horizontal divider
Mono enclosures
Used when the enclosure requires separa-
tion by partial doors or panels. Can be
mounted in the hole pattern of closed
frames (Mono versions).
Material: 2 mm zinc plated steel.
|821606 4
|821607 4
|821608 4
Side door
Replacing the side panel. For easy access
to the equipment inside the enclosure or
when enclosures are mounted rear to rear.
Lock: standard 3 mm double bit lock which
makes all lock options possible.
Material: 2 mm steel plate.
Finish: structure powder paint RAL 7032
|821609 1
|821610 1
|821611 1
|821612 1
Door mounting kit
Required when fitting a door to the rear of
an enclosure.
1 kit consists of 4 standard hinges, 4 rod
catchers and mounting material .
|821617 1
For single door enclosures
|821618 1
For double door enclosures
Inner door
Mounted on vertical plates, which prevent
access on the sides. The inner door provi-
des a hinged mounting surface for equip-
ment behind a standard or glazed frontdoor. A mounting space of 80 mm is availa-
ble between the doors when the inner door
is in forward position. The inner door can be
adjusted in depth by steps of 25 mm.The
mounting plate remains usable behind the
inner door. The door is equipped with two
locks, 3 mm double bit, and plastic handles
Material: 1.5 mm steel plate.
Finish: structure powder paint, RAL 7032.
|821613 1
|821614 1
| 821615 1
|821616 1
Door hinges 180
|821619 4
Enables the door to open 180 degrees,
even when enclosures are coupled together.
Material: die-cast zinc
Finish: blue
Door stop
|821620 1
To lock a door in open position.
Mounted directly to the doorframe and into
the enclosure profile. The full mounting area
of the frame is kept free.
Material: zinc plated steel.
Door wheel
|821621 2
For easier closing and positioning of a
heavily equipped door (cooling units etc).Mounted directly to the door frame on the
bottom of the door.
W = 400
W = 600
W = 800
W = 400
W = 600
W = 800
H D
1800 500
1800 600
2000 500
2000 600
H W
1800 600
1800 800
2000 600
2000 800
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
33/40
62
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
Accessories
Drawing desk
Mounted directly to the doorframe and it
provides a stable surface for documents,
computer or measuring devices. The desk
can be easily folded and locked within thedoorframe space. An automatic safety posi-
tioning system locks the desk at angles of
55, 70 and 90 degrees. The drawing desk
W=800 can also be mounted on a 1000 mm
wide door, by the use of the door mounting
profiles 1000 mm
Material: 1.5 mm steel plate.
Finish: structure powder paint, RAL 7032.
|821622 1
|821623 1
Document pocket
|811516 1
DIN A4
W x H = 325 x 180
Drawing pocket
A large steel document pocket fixed directly
onto the door frame. Usable depth: 68 mm.
Material: 1.5 mm steel plate.
Finish: structure powder paint, RAL 7032.
|821625 1
|821626 1
|821627 1
|821628 1
Front frame cover
To cover the framework around the door
aperture on 600 wide data-telecom enclosu-
res, when a door is not fitted.
Material: 2 mm steel plate.
Finish: structure powder paint, RAL 7032.
|821629 1
|821630 1
|821631 1
|821632 1
Door frame mounting profiles
Horizontal assembly profiles with 25mm
hole pattern. Fit directly onto door frame.
For easy mounting of light equipment by
using torx extrudetite screws M5, cablesrouting etc.
Material: 2 mm zinc plated steel.
|821633 2
|821634 2
|821635 2
|821636 2
|821637 2
Cable conduit
For flexible and safe protection of cables
installed between the door or swing frame
and the enclosure interior.
Highly flexible and halogen free.
Material: polyethylene.
|821638 25m
|821639 25m
|821640 25m
|821641 25m
Universal conduit holder
Universal holder for cable conduit.
Can be mounted horizontally or vertically on
any 25 mm hole pattern of door frame,
enclosure frame or accessory profile.
Material: polycarbonate.
|821642 10
|821643 10
|821644 10
|821645 10
Cable conduit
For flexible and safe protection of cables
installed between the door or swing frame
and the enclosure interior.
Highly flexible and halogen free.
Material: polyamide, UL approved.
|821646 25m
|821647 25m
|821648 25m
|821649 25m
W = 600
W = 800
W = 500/1000
W = 600/1200
W = 800/1600
W = 1000
H W
2000 600
2000 800
2200 600
2200 800
W = 400
W = 500
W = 600
W = 800
W = 1000
= 16
= 29
= 36
= 48
= 16
= 29
= 36
= 48
= 16
= 29
= 36
= 48
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
34/40
63
OPTIMALFS
Accessories
Cooling door
Standard door with integrated cooling unit to
be fitted to the OPTIMALFS single door
series. Attractive low profile design, that
bleeds in harmoniously with any machine orsystem. Optimum cooling by virtue of extre-
mely long passage of air in the inner airflow
circuit. Aluminum and stainless steel chas-
sis. Reliability under even the most extreme
conditions, since the electronics in the coo-
ling unit are located in the cooling circuit.
Power indicator light on the front. Use hinge kit
821617 if used in front of frame without door.
Equipped with 3 mm double bit locking system.
Protection: IP54 against the enclosure,
IP34 against the ambience (IEC 60529),
when used as recommended.
Standards: UL and cUL approved.
Material: door 2 mm and cooler cover
1.5 mm steel plate.
Finish: structure powder paint, RAL 7032
|821650 1
|821651 1
|821652 1
|821653 1
|821654 1
|821655 1
|821656 1
|821657 1
|821658 1
|821659 1
|821660 1
|821661 1
|821662 1
|821663 1
|821664 1
|821665 1
Roof ventilation unit
Ventilation unit for mounting on top of the
enclosure, providing high air flow and lownoise level by the use of a centrifugal fan.
Provided with sealing gasket to assure an
IP 33/NEMA 1 protection.
Free airflow 450 m3/h. Noise level: 61 dB.
Maximum temperature: 50 C. ULapproved.
Material: 1.5mm steel plate.
Finish:structure powder paint RAL 7032.
Package: 1 fan unit with connection cable,
mounting material and installation template.
|821666 1
230VAC - 50/60Hz
| 821667 1115VAC - 50/60Hz
Roof exhaust unit
|821668 1
Ventilation unit for mounting on the top of
the enclosure providing natural ventilation
i.e. without a fan. Asealing gasket to assurean IP 33 protection is supplied between the
unit and the enclosure roof. The standard fit-
ted dust filter protects the equipment up to a
level of IP 43/NEMA 1.
Material: 1.5 mm steel
Finish: structure powder paint RAL 7032.
Package: 1 exhaust unit with mounting
material and installation template.
Keys
|
832022 2
For safety lock No. V2432E
|832026 1
For safety lock with 8 mm square
|832027 1
For safety lock with 8 mm triangle
|832072 1
For safety lock with 11 mm triangle
|832028 1
For safety lock with double bit 3 mm
Lock cover
|821670 1
For inserts
Swing handle
|821671 1
Neutral handle
H W Watt Volt
1800 600 1000 230
1800 600 1500 230
1800 600 2000 400
1800 600 2500 400
1800 800 1000 230
1800 800 1500 230
1800 800 2000 400
1800 800 2500 400
2000 600 1000 230
2000 600 1500 230
2000 600 2000 400
2000 600 2500 400
2000 800 1000 230
2000 800 1500 230
2000 800 2000 400
2000 800 2500 400
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
35/40
64
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
Accessories
T-handles
|821706 1
Without cylinder
Swing handles
With inserts type:
|821690 1
Square 8 mm
|821693 1
Triangle 8 mm
|?????? 1
Triangle 11 mm
|821694 1
Double bit 3 mm
Inserts
Without cover
|821672 1
Double bit 3 mm
|821675 1
Square 8 mm
|821677 1
Triangle 8 mm
|?????? 1
Triangle 11 mm
Ventilated top cable cover
For cable entry on three sides in combina-
tion with ventilation. Cable openings provi-
ded with brushes.
For inside mounting of ventilation fans(821738) or closing plates for unused holes
in the top of the enclosure.
Material: 1.5mm steel plate.
Finish: structure powder paint, RAL 7032.
|821711 1
|821712 1
|821713 1
|821714 1
|821715 1
Fan
220-240VAC Fan. Air flow 160 m3/h. Wiring
kit consist of 6 pieces for connection to fan.
Round/flat connection.
|821738 1
Inside mounting
|821739 1
Top mounting
|821740 1
Wiring kit for max. 6 fans
Fan roof plates
For mounting a combination of 6 fans
(821739) or closing plates for unused holes
in the top of the enclosure. To be used in
combination with the ventilation roofs
(821716-821732).
Material: 2 mm zinc plated steel.
|821733 1
|821734 1
|821735 1
|821736 1
|821737 1
Closing plate
To close unused fan cut-outs.
Material: 1.5mm steel plate.
|?????? 1
W x D Cut outs
600 x 600 4
600 x 800 6
800 x 600 4
800 x 800 6
800 x 900 6
W x D
600 x 600
600 x 800
800 x 600
800 x 800
800 x 900
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
36/40
65
OPTIMALFS
Accessories
Ventilation roof
Raised roof with 2.5 mm ventilation slots
and filter material. Increases the enclosure
height by 40 mm. IP31 and NEMA 1
Temperature resistance: 100C.Material: 1.5mm steel plate.
Finish: structure powder paint RAL 7032.
Filter material: EU 4 acc. to DIN 24185.
Package consists of 1 piece with mounting
brackets and ventilation filter.
|821716 1
|821717 1
|821718 1
|821719 1
|821720 1
|
821721 1
|821722 1
|821723 1
|821724 1
|821725 1
|821726 1
|821727 1
|821728 1
|821729 1
|821730 1
|821731 1
|821732 1
Ventilated bottom plates
Three piece bottom plates. Can be used in
combination with a ventilated plinth.
Material: 1.5 mm perforated zinc plated steel.
|821390 1
|821391 1
|821392 1
|821393 1
|821394 1
Top cover with cable gland opening
For cable entry. Material: 1.5 mm steel plate.
Finish: structure powder paint, RAL 7032.
Package consists of 1 piece with gland
plates, gaskets and mounting material.
|821741 1
|821742 1
|821743 1
|821744 1
|821745 1
Spacer kit
|821746 1
Provides ventilation by raising the roof panel
15 mm.
Material: zinc plated steelPack: 1 kit = 4 pieces
19 mounting profiles
Full height mounting profiles to achieve
482.6 mm (19) mounting requirements on
all sides. Fully adjustable in depth.
To be used in conjunction with fixing
brackets 821766-821767 and 19 profiles
821769-821770.
Material: 2 mm zinc plated steel
|821747 2
|821748 2
|821749 2
|821750 2
|821751 2
|821752 2
19 support
Side universal 19 punchings. For additional
internal support. To be used in conjunction
with fixing brackets 821766-821767 and 19
profiles 821769-821770.
Material: 2.0 mm zinc plated steel.
|821753 2
|821754 2
|821755 2
|821756 2
W x D
600 x 400
600 x 500
600 x 600
600 x 800
800 x 400
800 x 500
800 x 600
800 x 800
800 x 900
1000 x 400
1000 x 500
1000 x 600
1000 x 800
1200 x 400
1200 x 500
1200 x 600
1200 x 800
W x D
600 x 600
600 x 800
800 x 600
800 x 800
800 x 900
W x D
600 x 600
600 x 800
800 x 600
800 x 800
800 x 900
Pictures are missing
H Units
1100 22
1400 29
1600 33
1800 38
2000 42
2200 47
Units
33
38
42
47
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
37/40
66
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
Accessories
19 mounting profiles partial
height
Partial height mounting profiles to achieve
482.6 mm (19) mounting requirements on
all sides. Fully adjustable in depth. To beused in combination with click-in profiles.
For 800 mm wide enclosures add special
bracket 821768.
Material: 2 mm zinc plated steel.
| 821757 2
|821758 2
|821759 2
|821760 2
|821761 2
|821762 2
|821763 2
|821764 2
|821765 2
Brackets for fixing 19 mounting
profiles
For fitting 482,6 mm full height mounting
profiles (19) in 600 and 800 mm wide
enclosures. Fully adjustable in depth.
Material: 3 mm zinc plated steel.
|821766 2
W/D = 600
|821767 2
W/D = 800
Depth mounting profiles (19) for
asymmetric fixing 19 profilesFor fitting asymmetricly 19 mounting
profiles in 800 mm or wider enclosures.
Fully adjustable in depth.
Material: 3 mm zinc plated steel.
|821769 4
D = 600
|821770 4
D = 800
Brackets for partial height
19 mounting profiles
|821768 4
For fixing 482,6 mm partial height mounting
profiles (19) in 800mm wide enclosures.Adjustable in depth in steps of 12.5mm,
by using the click-in profiles.
Material: 3 mm zinc plated steel.
Ventilated shelf
Mounted directly to enclosure frame.
The load carrying capacity is 50 kg.
Material: 2 mm zinc plated steel..
|821771 1
|821772 1
|821773 1
|821774 1
|821775 1
Telescopic ventilated shelf
Mounted directly to enclosure frame. The
load carrying capacity is 50 kg.
Material: 2 mm zinc plated steel.
Pack: 1 shelf + 1 pair of 3 member slides
|821778 1
|821779 1
|821780 1
|821781 1
Monitor shelf
Mounted directly on to the enclosure frame.
Provided with clamp-kit to hold the monitor
in position
Material: 2 mm zinc plated steel.
|821776 1
|821777 1
6 units
9 units
10 units
11 units
13 units
15 units
18 units
21 units
27 units
For enclosure
W D w d
600 600 509 555
600 800 509 755
800 600 709 555
800 800 709 755
800 900 709 855
For enclosure
W D w d
600 600 460 550
600 800 460 750
800 600 660 550
800 800 660 750
For enclosure
W D w d
600 600 509 555
600 800 509 755
EPS or DXF file please
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
38/40
67
OPTIMALFS
Accessories
Separation plates
Separates two coupled enclosures.
To be fixed with coupling kit 821803.
To achieve IP33/NEMA 1 a neoprene gas-
ket 821804 can be fixed to the panel.Material: 1,5 mm galvanised steel.
| 821782 1
|821783 1
|821785 1
|821786 1
|821787 1
|821788 1
|821789 1
|821790 1
Raised side door
The side door is used for easy and fast
access to the instrumentation fitted inside
the enclosure as well as for mounting of
accessories in the side of the enclosure.
Material: 2 mm steel plate
Finish: structure powder paint RAL 7032.
|821792 1
|821793 1
Marshalling plates
Connector plate between two enclosures, or
to be used in combination with a raised side
door. Hole patterns for 16 pin or 24 pin con-
nectors.To be mounted with bracket set 821803.
Material: 2 mm galvanised steel.
| 821794 1
|821795 1
|821796 1
|821797 1
Cover plates
To cover unused connector cut-outs of a
marshalling plate or as adapter for 16 pins
connectors to allow the mix of both type of
connectors
Material: 2 mm galvanised steel.
(including seal)
|821798 1
|821799 4
|821800 20
|821801 20
|821802 1
Internal coupling kit
| 821803 12For coupling enclosures. To be used when
separation or marshalling plates are fitted.
Material: 3 mm zinc plated steel.
Separation plate gasket
|821804 1
To obtain IP 33/NEMA 1 sealing in combina-
tion with the separation plates.
H x W
1800 x 400
1800 x 500
2000 x 400
2000 x 500
2000 x 600
2000 x 800
2200 x 600
2200 x 800
H x D
2000 x 500
2000 x 600
H x D
1800 x 500
1800 x 600
2000 x 500
2000 x 600
Description Size
Adapter plate 4 x 16 pin
24 pin to 16 pin
Cover plate 16 pin
24 pin
4 x 24 pin
Pictures are missing
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
39/40
68
Sheetsteelfloor
standing
enclosures
GE Power Controls
OPTIMAL FS
Accessories
Ltze system adaptor profiles
Adapter to fix the Ltze system direct to the
OPTIMAL FS enclosure frame. Adjustable
in depth by steps of 25 mm. The width of
the Ltze frame equals the enclosure nomi-nal width minus 22 mm.
Material: 2.5 mm zinc plated steel.
|821806 6
|821807 6
|821808 6
|821809 6
Levelling feet
|821813 4
Adjustable feet for the leveling of enclosures
placed on unevenground. Mounted directly
to the frame. Maximum load: 300 kg per
foot. Adjustment stroke = 30 mm.
Gasket for EMC shielding
|821805 1
To obtain an EMC shielded section in a
suited panel in combination with the
separation plate.
Protection: IP 33/NEMA 1.
Wheels
For easy moving of the enclosure.
To be mounted to the frame by brackets.
Maximum load: 240 kg.
Raises the enclosure by 70 mm.
|821810 4
Without breaks
|821811 4
2 with breaks / 2 without breaks
|821812 4
With breaks
Swing frame
For 600/800/1000 mm wide enclosures.
All swing frames require the transversal
mounting kit (see next page).
|821846 1
For mono single door + ind. data enclosure
|821847 1
For modular single door + mono single door
|821848 1
For industrial data enclosure
|821849 1
For modular single door + ind. data enclosure
Swing frame, centered
For 800/1000 mm wide enclosures
All swing frames require the transversal
mounting kit (see next page).
|821850 1
For mono single door + ind. data enclosure
|821851 1
For modular single door + mono single door
|821852 1
For industrial data enclosure
|821853 1
For modular single door + ind. data enclosure
D = 400
D = 500
D = 600
D = 800
H U Max. load
1600 31 170
1800 35 195
2000 40 195
2200 44 195
H U Max. load
1600 31 170
1800 35 195
2000 40 195
2200 44 195
-
8/9/2019 GE Optimal Sheet Steel Cabinets030-069
40/40
OPTIMALFS
Swing frame brackets
|821863 4
For full and/or partial height mounting of
swing frames in OPTIMAL FS enclosures.Material: 3 mm zinc plated steel
Transversal mounting kit
Material: 3 mm zinc plated steel
|821864 1
W = 600
|821865 1
W = 800
|821866 1
W = 1000
Accessories
Swing frame, side mounted
For 800/1000 mm wide enclosures
All swing frames require the transversal
mounting kit (see below on page).
|821854 1
For mono single door + ind. data enclosure
|821855 1
For modular single door + mono single door
|821856 1
For industrial data enclosure
|821857 1
For modular single door + ind. data enclosure
Hinges 180
|821859 1 kit
19-44 U
Only usable in 800 mm width and above.
Chassis support
|821820 2
To relieve pressure on heavy chassis appli-
cations.
Material: 1.5 mm zinc plated steel
Swing frame stop
|821861 1
Locking in any position up to maximum
opening.
H U Max. load
1600 31 170
1800 35 195
2000 40 195
2200 44 195
Drawing in Illustrator eps
or dxf please