fsmf-site engineering-v1.pdf

8/17/2019 FSMF-Site Engineering-v1.pdf

http://slidepdf.com/reader/full/fsmf-site-engineering-v1pdf 1/15

©2013 Nokia Solutions and Networks. All rights reserv

FSMF module and FPFD optional module

Site Engineering/ 25.01.2014



2 ©2013 Nokia Solutions and Networks. All rights reserved.25-Jan-14

Contents of delivery of Flexi Multiradio 10 modules (1/3)




FSMF plug in modules

With covers for stack, wall and pole installation

Without covers for cabinet and rackinstallation

Optional basebandtechnology

extension sub-mo

Optional, one transp

Optional, one integradistribution (FPFD)




FSMF External connectors

DC-Out

4x 16mm²

Sy

H

EAC

HDMI

EIF1

RJ45

BB EXT2

QSFP

BB EXT1

QSFP

sRIO

SFP+

RF/EXT1..3

3x SFP+

EIF2/RF/6

SFP+

RF/EXT

SFP+

BB EXT

QSFP

sRIO

SFP+

DC-in

PwrProfile

DC-out

PwrProfile

DC-out

PwrProfile

DC-in

2x 16mm²

LMP

RJ45

External Connectors

•EAC: 6 Alarm signals and 6 signals that are SW assignable for either Alarm or Control signals CAN bus interface

connector type used for the EAC interface

•FSMF has a 48V input screw terminal connector on the front panel for power input of its own, if FPFD is not used




Power connection to FSMF (when optional FPFD is not used)

Installation of FSM

panel DC interface

(without optional FP

installed) requires afuse. The fuse size

between 20 A and 3




Integrated optional (FPFD) module

Flexi Power Distribution Sub-Module (FPFD) is a highly

integrated optional size-optimized power distribution unit (PDU)

for System Module variant FSMF. It is installed in the top left slot

of the System Module.

FPFD provides four external -48 V DC outputs (fixed to 1100 W)

for Flexi Modules (RF Module, RRH, or external System Module)

or any standard 48 V DC device at the site, and one internal DC

output to System Module itself via internal connector (MEC8).

FPFD has integrated basic Over Voltage Protection (OVP Type

approval level with 2kV/1kV), EMC filtering and reverse polarity

protection. It is IP65 rated.

Flexi Power Distribution Sub-Module (FPFD) can be used forstacked and feederless configurations in the same way as earlier

integrated Flexi PDUs.




FPFD interfaces

The FPFD provides the following external interfaces:

One -48 V DC input (4-25 mm2/4 AWG)

Four external -48 V DC outputs (4-16 mm2/6 AWG screw terminals)

One internal DC output to the System Module

ON/OFF switches & status LEDs at the control panel

The control panel is located on the front pa

Flexi Multiradio 10 BTS Power Distribution

Sub-Module (FPFD). There are five LEDs f

corresponding output ports,

and two push buttons for the ON/OFF func

the outputs.




Power connection to FPFD (FSMF powered via FPFD)

When FPFD

feeds the FS

in port internacase make su

FSMF front p

interface port

with IP seal a

The fuse size

between 100if all 4 ports w

connected to




Routing the FPFD power input cable

The two FPFD DC input cables can be rout

FPFD and dummy unit or transmission card

no space for both cables, one of them can

the right side of FTIF card.




DC cable requirements for 80 W RF Modules

The DC cable is not included in the 80 W RF Module delivery. 48 VDC power can be fed from a

System Module or directly from an external power source

If FXEB/FRGT is used with FSMC/D/E or FPFC/FPFD (30A PDU), then the rules of below table

should apply.

Only if low voltag

472806A:FPCA DC cable 2xmultibeam cu

cable)

Standard DC cable open-open (single cable) for

outdoor use




FPMA AC wiring and fuse requirements

The recommended wire cross section and fuse size for FPMA is listed below




EAC cable(FTSI 472578A) wiring

fsmf-site engineering-v1.pdf

Documents