FS-210 Housing Operator's Manual

For Nikon Coolpix S210 Digital Camera

2

TABLE OF CONTENTS

TABLE OF CONTENTS ................................................................................................................................. 2

GENERAL INFORMATION .......................................................................................................................... 3

THE FANTASEA FS-210 HOUSING .................................................................................................................... 3

FANTASEA FS-210 USES .................................................................................................................................. 3

GENERAL DESCRIPTION OF CAMERA ............................................................................................................... 9

NIKON COOLPIX S210 FEATURE HIGHLIGHTS ............................................................................................... 10

USING THE FANTASEA FS-210 HOUSING ............................................................................................. 11

OPENING THE HOUSING ................................................................................................................................. 11

INSERTING CAMERA....................................................................................................................................... 11

CHECKING THE O-RING .................................................................................................................................. 12

CLOSING THE HOUSING.................................................................................................................................. 13

VIEWING THE SUBJECT ........................................................................................................................... 14

TAKING THE PICTURE .................................................................................................................................... 14

CHOOSING IMAGE FILES ................................................................................................................................ 14

BATTERY LIFE ............................................................................................................................................. 15

USING THE FLASH ...................................................................................................................................... 16

ACCESSORY SLAVE FLASH ............................................................................................................................ 16

LENS ACCESSORIES ....................................................................................................................................... 17

FANTASEA COOLPIX ACCESSORY SYSTEMS AND SETS .................................................................................. 17

SHOOTING TECHNIQUES ......................................................................................................................... 18

EXPOSURE MODES (PRE-SET BEFORE CAMERA INSERTION) .......................................................................... 18

ZOOM CONTROL ............................................................................................................................................ 18

MACRO FOCUS ............................................................................................................................................... 18

QUICK REVIEW .............................................................................................................................................. 18

CAMERA STANDBY MODE ............................................................................................................................. 19

CARE & MAINTENANCE ........................................................................................................................... 20

3

GENERAL INFORMATION

The Fantasea FS-210 Housing

Fantasea has specially designed the FS-210 housing for the Nikon Coolpix S210 camera. This

housing is ideal for outdoor and underwater photographers who enjoy the cameras automatic

exposure features for capturing fast action pictures easily and creatively. The FS-210 housing

ensures easy handling and accurate access to camera functions through the critical placement of

push-button controls and a compact design.

The FS-210 housing provides access to all control functions: On/Off, Shutter Release, Mode,

Zoom In/Out, Menu, Flash, Exposure Compensation, Timer, Macro, Playback and Delete, and

has a built in Flash Diffuser and an anti-glare hood over the LCD screen.

Fantasea FS-210 Uses

The Fantasea FS-210 housing is designed as an underwater/outdoor camera housing. It features

double O-rings on all controls, and has a working depth of 200 feet/60 meters. Underwater

photographers can dive or snorkel and capture all the excitement of this fascinating world, while

outdoor photographers also have the option of capturing the action of such activities as white

water and paddle sports, swimming, sailing and boating, surfing, fishing and hunting,

backpacking and camping. The Fantasea FS-210 will protect the Coolpix S210 camera from

water, sand, dust, and other damaging elements.

4

Top/Front Side of Housing

Numbered description below refers to corresponding numbers on above graphic.

1. Shutter Release

This is a two stage shutter-release button. First lightly press the shutter-release button halfway,

stopping when you feel minimal resistance. Once the camera has focused, press the shutter-release

button the rest of the way down to release the shutter and take the picture.

2. Power On/Off

To turn on the camera, press the power switch. The power-on lamp (green) will turn on for a moment,

and the monitor will turn on.

To turn off the camera, press the power switch again.

2. Power On/Off

1. Shutter Release

5. Buckles to

Secure Housing

3. Removable Flash

Diffuser

4. Threaded Lens

Port

5

3. Removable Flash Diffuser

The Flash Diffuser is used to diffuse the flash's intensity [the internal flash]. See the section on

"Accessory Slave Flash" for additional information.

4. Threaded Lens Port

Refer to the section "Inserting Camera" for useful information.

5. Buckles to Secure Housing

Refer to the section "Using the Fantasea FS-210 Housing" on how to open and close the camera

housing.

Back Side of Housing Buttons

7. Zoom In/Out 6. Mode

9. Flash Mode

10. Exposure

Compensation

12. Self-Timer

11. Macro

14. Delete

15. Menu

8. Playback

13. OK button

6

Numbered description below refers to corresponding numbers on above graphic.

6. Mode

Press the Mode button during shooting to display the shooting mode selection menu (Auto, Scene,

Setup, High sensitivity, Movie or Voice recording mode), or during playback to display the playback

mode selection menu (Playback, Calendar, Audio playback, List by date or Setup mode).

Use the multi selector and press the OK button to choose the desired mode.

Press the Playback button to switch between the mode selection menus for shooting mode and

playback mode.

7. Zoom In/Out

Use the Zoom buttons to activate optical zoom. Press "W" to zoom out, increasing the area visible in

the frame, or "T" to zoom in, so that the subject fills a larger area of the frame. When the camera is

zoomed to the maximum magnification (3x), holding "T" down triggers digital zoom. The subject is

magnified up to 4x, for a total magnification of 12x. A monitor indicator shows the current zoom

ratio.

Press "W" in full-frame playback to display pictures in "contact sheets" of four or nine thumbnail

images.

Press "T" to zoom-in on still images displayed in full-frame playback.

When entering a menu, press "T" to view a description of the currently selected menu option.

8. Playback

Press the Playback button to enter full-frame playback. Multi-selector buttons may be used to view

pictures.

Press Playback button again or press the shutter-release button to return to shooting mode.

If the camera is turned off, hold down the Playback button to turn the camera on in playback mode.

7

Multi-Selector buttons (9-13)

9. Flash Mode

In order to select a flash mode:

Press the Flash Mode button.

Use the multi-selector up/down arrows to choose the desired flash mode (Auto, Auto with Red-Eye

Reduction, Off, Fill Flash and Slow Sync), and press "OK".

10. Exposure Compensation

Exposure Compensation is used to alter exposure from the value suggested by the camera to make

pictures brighter or darker.

Press the Exposure Compensation button.

Press the multi-selector up/down arrows to adjust exposure, and press "OK".

11. Macro

Macro Close-Up mode is used for taking pictures of objects as close as 10cm/3.9 inch.

Press the Macro Mode button.

Press the multi-selector up/down arrows to choose "On", and press "OK".

Press "T" or "W" to frame the picture, focus and shoot.

12. Self-Timer

The camera is equipped with a ten-second and two-second timer for self portraits. When using the self-

timer, mount the camera on a tripod or rest it on a flat and stable surface.

Press the Self-Timer button.

Press the multi-selector up/down arrows to choose 10 seconds or 2 seconds, and press "OK".

Frame the picture, press the shutter-release button half-way to focus, and then all the way down.

13. OK Button

Push this button to confirm a selection.

In full-frame playback, press the OK button to compensate for a blurred image (Electronic VR). Use

the multi selector to choose "OK" and press the OK button again. A compensated image is created.

8

14. Delete

Press Delete to delete the picture currently displayed in the monitor in full-frame playback. Press the

multi-selector up/down arrows to choose "Yes", and press "OK".

In Shooting Mode, press this button to delete the last picture taken. When the confirmation dialog

shown at right is displayed, press the multi-selector up/down arrows to choose "Yes", and press

"OK".

15. Menu

Press the Menu button to display the menu for the selected mode:

Shooting menu

High-sensitivity menu

Scene menu

One-touch portrait menu

Movie menu

Playback menu

Calendar menu

List by date menu

Note! It is strongly recommended that you familiarize yourself with all the

controls topside before using these controls while diving.

9

GENERAL DESCRIPTION OF CAMERA

The S210 is a stylish new camera that's a

pleasure to carry and a joy to shoot with.

Built on a custom application of Nikon's

innovative EXPEED digital image processing

concept and incorporating the precision optics

of a NIKKOR lens, the Coolpix S210 places

advanced shooting functions comfortably in

the hand.

The camera features a sharp resolution of 8.0 effective megapixels. It is equipped

with a 3x Zoom Nikkor lens that covers a practical range from 38-114mm (35mm

format equivalent), which enables the underwater photographer to capture

everything from close-up fish portraits to underwater scenery shots. The Electronic

VR image stabilization adds extra reassurance that the results will be sharper and

clearer, especially in lower light or when shooting moving subjects. The image

processing engine faithfully reproduces fine details and subtle tones, delivers quick

response, and maintains image quality and clarity when taking advantage of

extended light sensitivity settings as high as ISO 2000.

The camera is also equipped with a large 2.5" LCD screen which displays photos

crisply and allows the photographer to observe even the smallest details in the

frame.

The Coolpix S210 is housed in a slim, quality-crafted aluminum body with gentle

contours that fit comfortably in the hand. Functional beauty and classic camera

appeal are the theme throughout, from the elegant look on the front to the clean

design of the back with large control buttons and user-friendly rotary multi

selector, carefully positioned to provide intuitive operation.

10

NIKON COOLPIX S210 FEATURE HIGHLIGHTS

Proven optical lens shift VR Image Stabilization

Field proven technology originally developed for interchangeable lenses

used in Nikon SLR camera systems, optical lens shift VR image

stabilization provides the ability to shoot at shutter speeds as much as

three steps slower without blurring the image, whilst also producing a

smoother image when shooting.

.Large and Bright LCD Monitor

The camera is equipped with a quality 2.5-inch LCD monitor that features

230K-dots of high resolution, a wide 170-degree horizontal and vertical

viewing angle, anti-reflection coating for better display in bright

situations, and an acrylic panel that prevents scratches and fingerprints.

Improved shooting displays with revised icons and information feedback

help make framing and shooting easier.

ISO 2000 capability for better pictures in low light

A high ISO makes it easier to take great looking pictures in low light

conditions or to capture fast moving subjects in outstanding clarity, like

in underwater photography. The camera accurately measures available

light to automatically select the optimal sensitivity setting for the shot

between the range of ISO 64 to as high as ISO 2000.

11

USING THE FANTASEA FS-210 HOUSING

OPENING THE HOUSING

1. Release all four latches at the same time, and lift off back half to open housing.

INSERTING CAMERA

Since the Fantasea FS-210 is specifically designed for the Coolpix S210 digital camera, inserting the camera

into the housing is quite simple.

1. Mount the camera on the removable tray, using the tripod screw.

2. Slide the tray and camera into the housing tray slot. Make sure it is completely inserted.

3. Make sure the camera lens is more or less centered in the rounded port area and that the lens does not

distort the round black rubber seat. The housing is designed to have the camera fit in place perfectly,

but if you are not careful, it is possible to put it in at an improper angle and it will then be impossible

to get a good seal or easy closure of the housing.

4. After camera insertion, check that the extended camera lens does not catch or bend the black

rubber seat on the inside of the lens port. It is vital that the lens does not disturb this rubber

seat.

Note!

It is strongly recommended to take the first dive without the camera

inside the housing. You should check that the water tight seal has

not been affected during transport and long periods of storage.

12

Notes:

1. It is recommended to make some camera settings prior to

inserting camera into the housing. Please refer to the

Coolpix owner's manual for menu options and personal

preferences.

2. Take a few test shots: it is recommended to turn the camera

"on" and program to “Flash Always” mode before inserting

into housing and then take test shots to make sure all

systems are working.

Underwater photographers will probably want to set the flash mode to the flash always setting to ensure

they always have a flash with every exposure. It is also wise to set the focus mode to allow the lens to focus

in the macro range for capturing great images of the tiny and exotic subjects that you can find underwater.

CHECKING THE O-RING

Prior to each closure of the housing the O-ring should be visually inspected. If there is any debris present,

including dirt, sand, dust, hair, grease or other matter, it must be cleaned to ensure a proper watertight seal.

Cleaning the O-ring is a simple matter of wiping it with a damp, soft cloth to remove the foreign matter. Be

careful the cloth you use does not leave any of its own material behind as this can also affect the

effectiveness of the seal. When replacing the O-ring, place it back into the groove starting at one corner and

gently place it in by pressing it into the groove all around the housing until it is all sitting in the groove and

no part of it is sticking up or out of the groove. You can then apply a slight layer of silicone if you have not

done this yet. Be sure it is completely seated in the channel for a proper seal.

Note

Lubrication of an O-ring does not improve the seal. It only reduces the

amount of friction on the O-ring when it is being moved into sealing

position. The amount of lubrication required on the O-ring is only enough

to allow it to slip into place without friction, so it does not twist or become

dislodged. More grease is not better, and could in some cases have a

negative affect if it is applied in large amounts to form a build-up that

could trap any debris or foreign matter.

13

CLOSING THE HOUSING

1. Place housing back over front and align the complete mating surface of the housing and the O-

ring, forming a proper seal.

2. Position all four latches over latch hooks in ready position.

3. Close one of the bottom latches first, maintaining pressure on the other side. Proceed by closing

the other side's top latch. Then close the remaining bottom latch and the remaining top latch. Test

all latches carefully to make sure that they are completely locked into place and not just pushed

down. Try to open them to make sure that they cannot open accidentally.

4. Inspect the O-ring for proper closure. A complete seal can be visually confirmed by the O-ring

around the complete circumference of the housing.

5. Always take the first dive without your camera in the housing just to make sure there is no leakage

from damage to the housing. During the dive, especially at the beginning of descent, take special care

to look at the housing to make sure no bubbles are escaping from it and that no water is entering.

Generally, if there is a problem with the seal, you will discover it in the first seconds of the dive.

6. After use, when opening the housing, it is important to hold it so the lens port is facing down. This

will prevent the camera from slipping out of the housing while being opened. Release the four latches

in the same order described for closing them in step 3, and take off the back side of the housing.

Gently pull both the tray and the camera outside of the housing and unscrew the tripod screw out of

the camera in order to disconnect it from the tray.

14

VIEWING THE SUBJECT

The S210 camera does not have a standard eyepiece, but underwater photographers and outdoor

photographers will appreciate the large 2.5 inch LCD viewing monitor for composing photographs. The LCD

monitor allows you to see your subject in sharp focus and framed properly. Hold the camera housing in your

outstretched arm at a position that is both comfortable and also allows you to easily see the LCD monitor, for

best compositional options.

TAKING THE PICTURE

Once you have composed your scene or subject in the LCD monitor, depress the shutter release button to take

the picture. A half depress will activate the live viewing ability of the LCD and allow the camera to focus,

once in focus and ready to shoot a green light will appear on the LCD monitor and the camera is ready to

take the picture. Press down the shutter all the way to complete image capture. You may notice a pre-flash

and slight delay in the shutter release. This is to allow the camera to make its final focus and exposure

calculations before taking the picture. With a little practice, you will become used to this and taking pictures

of moving subjects will become easier and natural.

CHOOSING IMAGE FILES

There are several image file options to choose from that offer different resolution and file sizes. This

determination must be made prior to camera insertion from Menu options. Please refer to the Coolpix

instruction manual for details on setting these preferences.

15

BATTERY LIFE

Rechargeable Li-ion Battery EN-EL10

There are certain things that users can do to help with battery life. The most important is to set the camera to

turn the LCD off after a short time, during periods of non-use. It can then be automatically turned back on if

you depress the shutter release control half way. Please refer to the Coolpix instruction manual for details on

how to make this adjustment setting. It is always wise to have backup batteries in case you do run out of

power. The supplied battery can be recharged many times and offer an economical and environmentally

friendly power source.

16

USING THE FLASH

The Coolpix has a built-in flash, which will illuminate nearby underwater subjects. For subjects that are

farther away, an accessory slave flash is recommended (see below). A built-in flash diffuser is supplied

which will help achieve a wider and softer light source thereby providing more coverage and less likelihood

of backscatter (the unattractive snowstorm affect of the flash reflecting off the suspended particles in the

water). Further reduction of backscatter can be achieved by using an accessory off-camera slave flash. This

will be discussed in more detail later.

The need for artificial light to maximize color reproduction is necessary in nearly all pictures. Therefore it is

strongly recommended that you set the flash mode to Flash Always. This will ensure the flash fires on every

exposure regardless of the ambient light conditions (Please refer to the camera's instruction manual for more

details).

Outdoor photographers do not have this same concern. There is no backscatter to be concerned with, and due

to the ability of the flash to travel farther and more effectively in air as compared to in water, there is

normally not a need for an accessory flash to provide proper illumination for most subjects.

ACCESSORY SLAVE FLASH

If you use the Coolpix built-in flash as the master, you can trigger a second slave flash to provide more

artificial light when needed. To do this, you must use an accessory flash that has a slave feature built in. The

flash from the Coolpix must be aimed or bounced towards the accessory flash's slave sensor, or other fiber

optic sensor. This will trigger the slave to fire in sync with the master flash.

When using an accessory slave flash with fiber optic cable, it is recommended to black out the internal

camera flash. The internal flash is located near the camera lens and can contribute to backscatter by

illuminating floating particles close to the lens port or a shadowing effect caused by the lens port.

If the sensor of the fiber optic cable is attached to the outside of the housing directly above the internal flash

and taped over with black tape–it will block out the light from the internal flash but transmit the light pulse to

the external slave flash

Note Be sure to use a slave flash that has the ability to ignore the built-in pre-flash in

digital cameras, and synchronizes with the shutter release.

17

LENS ACCESSORIES

The Fantasea FS-210 features a threaded 46mm lens port. This threaded port is designed to work with some

of the wide-angle and macro adapters that are currently on the market. Fantasea Line offers the following

lens accessories:

FWAL-02 Wide Angle Lens: an accessory Wide Angle Lens which fits over the housing port and can

be installed and removed during the course of the dive.

Red Filter 46: fits over the housing port and can be installed and removed during the course of the

dive. The filter is mounted on the housing lens port and held in place by screw thread.

For more information on these items, see your local photo dealer or visit our website at www.fantasea.com

FANTASEA COOLPIX ACCESSORY SYSTEMS AND SETS

Fantasea offers a variety of sets for Coolpix and other housings. These sets are made up of quality accessory

products which will enhance and improve your underwater images. Accessory products include external flash

systems, flexible arms, trays, filters, wide angle lenses, fiber optic cables, bags and more. Below you can see

one sample system. For more information please refer to our website or to the Fantasea Dealer where you

purchased your housing.

NANO FLASH

LENS CADDY FOR

HOLDING ACCESSORY

LENS PRODUCTS

FLEX ARM

NANO FOCUS LIGHT

FIBER OPTIC

CABLE

XL STAY SLOT TRAY

MACRO / WIDE ANGLE

ACCESSORY LENS

FANTASEA HOUSING

18

SHOOTING TECHNIQUES

EXPOSURE MODES (PRE-SET BEFORE CAMERA INSERTION)

There are several exposure modes for photographers to choose from, depending on the situation. Underwater,

it is recommended that you shoot in the Auto mode on the camera, in which ambient light and artificial light

will be automatically controlled by the camera according to the lighting conditions. You can also select

different light meters to use, based on the situation and your personal preferences. Additionally, you can

choose the Auto White Balance setting for color temperature control, or experiment with some of the other

modes to see which will work best underwater. These settings do not have to be made ahead of any dive, as

they can be accessed through the housing controls while underwater.

Please refer to the Coolpix instruction manual for details on how to set these camera options, and under what

conditions the different choices should be used.

ZOOM CONTROL

Zoom in for telephoto photos and larger subject size. Zoom out for wide-angle scenes. It is generally not

recommended to use the zoom underwater as it is preferable to get physically closer to your subject. The

digital zoom has no value at all.

MACRO FOCUS

For capturing the tiny and exotic subjects that require close focus. Macro focus is possible when the lens is in

the wide-angle position.

QUICK REVIEW

Immediate review of most recent image is available and this will confirm that you have captured the shot you

want. However, if you want to scroll through your images, or delete images from the memory card, this

should be done when you are topside and the camera is out of the housing.

19

CAMERA STANDBY MODE

You can access the camera's menu to select the length of the inactivity period. Inactivity period is the length

of time before the camera goes into standby mode. Options are 30 seconds, one minute, five minutes, and 30

minutes. This feature allows you to conserve battery power by placing the LCD monitor on standby [sleep

mode]. It is recommended that this option is set for 30 seconds to conserve battery power. If set for longer

periods of time the LCD screen will heat up and it will produce condensation and fogging of the lens port.

Condensation on the lens port will have a negative impact on the quality of the images taken.

When you want to resume shooting, pressing the shutter release half-way will re-activate the camera.

However, if after the camera goes into standby, a further period of three minutes goes by without any

activity, the camera will turn off [deep sleep mode]. You can turn it back on by pressing the On/Off

Power button. The Welcome to Nikon Coolpix screen will appear and then it will display last image

taken.

20

CARE & MAINTENANCE

The Fantasea FS-210 housing requires only a minimum amount of care for reliable performance. The

following tips will enable you to get the best results.

1. Always rinse your housing with a strong stream of fresh water and if possible soak housing in

a fresh water tub or rinse tank for about 20 minutes after every dive in order to dissolve the

salt water crystals from around the controls and openings of the housing. Manipulate each of

the movable controls to assist the removal of salt particles from these tight areas.

2. Allow the housing to dry thoroughly before packing away for the day or for the trip home.

You may use a soft towel or cloth to dry the housing. Be sure there is no grease or other debris

on the towel.

3. Visually check the condition of the O-ring before every dive. If it is dirty, clean it with fresh

water and dry it with a soft cloth as described above. If it is damaged in any way, such as cut

or perforated, replace it before using the housing again.

4. It is recommended to slightly lubricate the housing's O-ring periodically. It's important to note

that the amount of lubrication required on the O-ring is only enough to allow it to slip into

place without friction, so it does not twist or become dislodged. More grease is not better, and

could in some cases have a negative affect if it is applied in large amounts to form a build-up

that could trap any debris or foreign matter.

5. Be careful not to get greasy fingerprints or dirt on the lens port. This will affect the image

quality. Wipe any dirt or grease off with fresh water and a soft cloth.

6. Do not drop the housing on hard surfaces, it could crack and affect its watertight seal integrity.

7. Travel with the housing protected in a padded case. It is best to remove the camera from

inside the housing when traveling and provide it with its own protective case, or compartment.

8. Never dive with the Fantasea FS-210 housing to a depth greater than 200 ft/60 meters.

9. It is recommended that you select the shortest time option on the menu, for placing the camera

into standby during periods of inactivity. This will conserve battery power and reduce the heat

given off by the LCD screen, which can contribute to condensation inside the housing and

fogging.

21

10. You should take the first dive without the camera inside the housing. You should check that

the water tight seal has not been affected during transport and long periods of storage.

11. It is likewise recommended to visually monitor the housing during every descent, especially

for the first 10 meters/33 ft. If water is observed entering the housing or bubbles escaping

from it, the housing should be rotated to a port down position and held that way as you return

to the surface immediately and get it out of the water.

12. It is recommended to have all Fantasea housings serviced once a year at an authorized Service

Center. This includes visual inspection and possible changing of all seals, gaskets and O-rings.

Please contact Fantasea by email at info@fantasea.com, or visit the Fantasea web site

www.fantasea.com for more information.