framed construction incorporating fluid-applied vapor
TRANSCRIPT
Senershield-R/-RS/-VB Framed Construction Incorporating Fluid-Applied Vapor Permeable and Impermeable Air/Water-Resistive Barriers Typical Details
(THIS PAGE INTENTIONALLY LEFT BLANK)
Notes: • Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• The details within represent Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. They are presented in good faith by Master Builders Solutions. The details are subject to change without notice. Master Builders Solutions accepts no liability for the end use of the details. For conditions not shown, consult Master Builders Solutions for review of specific detail.
1. Typical Joint and Fastener Treatement 2. Typical Vertical Expansion Joint 3. Typical Rough Opening Corner Reinforcement 4. Typical Rough Opening Reinforcement with Sheathing Fabric 5. Typical Quick Corner Application 6. Typical Rough Opening Reinforcement with Quick Corners and
Sheathing Fabric 7. Typical Rough Opening Reinforcement with Quick Corners and
Master Builders Solutions WS Flash 8. Typical Penetration through Wall Construction (Fabric Only) 9. Typical through Wall Construction (with MaxFlash or Sealant) 10. Typical Penetration through Wall Construction (Rough Cut) 11. Typical Inside Corner Change in Substrate 12. Typical Inside Corner 13. Typical Outside Corner 14. Typical Window Flange Treatment 15. Typical Window Head 16. Typical Window Jamb 17. Typical Window Sill 18. Typical Pan Flashing 19. Typical Termination at Grade – Sheathing Overlapping Foundation 20. Typical Termination at Grade – Sheathing Overlapping
Foundation with EIFS 21. Typical Termination at Grade – Sheathing Flush with Foundation 22. Typical Termination at Grade – Sheathing Flush with
Foundation and EIFS
23. Typical Termination at Grade – Sheathing Overlapping Foundation with Siding
24. Typical Termination at Grade – Sheathing Flush with Foundation and Siding
25. Typical EIFS Abutment to Siding 26. Typical Termination at Grade – Masonry Veneer 27. Typical EIFS Abutment to Masonry Veneer 28. Typical Brick Anchor Treatment
(Installed Prior to AWRB Application) 29. Typical Brick Anchor Treatment
(Installed After AWRB Application) 30. Typical Brick Expansion Joint 31. Typical Termination at Grade – Brick 32. Typical Termination at Foundation incorporating Sheathing
Fabric with Through Wall Flashing – Brick 33. Typical Termination at Foundation incorporating a Termination
Bar with Through Wall Flashing – Brick 34. Typical EIFS Abutment to Brick with Drainage at Floorline 35. Typical EIFS Abutment to Brick 36. Typical Through Wall Flashing at Head – Brick 37. Typical Saddle Application incorporating Sheathing Fabric 38. Typical Saddle Application incorporating WS Flash 39. Typical Kick-Out Flashing 40. Typical Roof Edge Flashing 41. Typical Parapet Cap Flashing
Senershield-R/-RS/-VBTypical Details
Framed Construction Incorporating Fluid-Applied Vapor Permeable and Impermeable Air/Water-Resistive Barriers
Table of Contents
(THIS PAGE INTENTIONALLY LEFT BLANK)
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Ensure all fastener heads are spotted with Senershield-R/-RS/-VB.
• Spot all fasteners not at sheathing joints. • Apply MaxFlash™ Liquid Flashing
Membrane or embed Sheathing Fabric in Senershield-R/-RS/-VB, or MaxFlash over joints.
• For more information, reference the Senershield Application Guidelines for Joint Treatment and Flashing Rough Openings on Framed Construction technical bulletin.
TYPICAL JOINT AND FASTENER TREATMENT
AWRB-01 2109
FRAMING*
ACCEPTABLE SHEATHING*
SHEATHING FABRIC OR MAXFLASH
SPOT FASTENERS WITH SENERSHIELD-R/-RS/-VB
SENERSHIELD-R/-RS/-VB
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-02 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
•ProvidesufficientslackintheMasterBuilders Solutions WS Flash at expansion join to allow for movement.
TYPICAL VERTICAL EXPANSION JOINT
FRAMING*
ACCEPTABLE SHEATHING*
9" MASTER BUILDERS SOLUTIONS WS FLASH WITH MASTER BUILDERS SOLUTIONS FLASHING PRIMER
SENERSHIELD-R/-RS/-VB
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-03 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Wrap rough opening in accordance with AWRB-7
TYPICAL ROUGH OPENING CORNER REINFORCEMENT
9' SHEATHING FABRIC
SHEATHING FABRIC READY FOR INSTALLATION
FOLD AND CREASE SHEATHING FABRIC
CREASE FROM PREVIOUS STEPNOTE: LENGTH OF CREASE DETERMINED BY ROUGH OPENING DEPTH
LAP MASTER BUILDERS SOLUTIONS SHEATHING FABRIC OVER TREATED CORNEREMBED SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB
FOLD AND CREASE SHEATHING FABRIC
APPLY SENERSHIELD-R/-RS/-VB IN ROUGH OPENING CORNER AND ONTO SHEATHING
LAP MASTER BUILDERS SOLUTIONS SHEATHING FABRIC ONTO FACE OF SHEATHING
CREASE FROM PREVIOUS STEPCUT SHEATHING FABRICNOTE: LENGTH OF CUT DETERMINED BY ROUGH OPENING DEPTH
COMPLETED CORNER TREATMENT APPLICATION
STEP 1
STEP 3
STEP 5
STEP 7
STEP 2
STEP 4
STEP 6
STEP 8
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
5) EMBED MASTER BUILDERS SOLUTIONS SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB
4) LAP MASTER BUILDERS SOLUTIONS SHEATHING FABRIC OVER TREATED CORNER
TREAT ALL SHEATHING JOINTS WITH MASTER BUILDERS SOLUTIONS SHEATHING FABRIC3) FOLD MASTER BUILDERS SOLUTIONS SHEATHING FABRIC ONTO FACE OF SHEATHING2) APPLY MASTER BUILDERS SOLUTIONS SHEATHING FABRIC AND CUT HERE1) APPLY SENERSHIELD-R/-RS/-VB
EMBED MASTER BUILDERS SOLUTIONS SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB
EMBED MASTER BUILDERS SOLUTIONS SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB
EMBED MASTER BUILDERS SOLUTIONS SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB
STEP 1 – CORNERS AND JOINTS APPLICATION
STEP 1 – CORNERS AND JOINTS APPLICATION
STEP 1 – CORNERS AND JOINTS APPLICATION
STEP 1 – CORNERS AND JOINTS APPLICATION
AWRB-04 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Ensure Sheathing Fabric is embedded in Senershield-R/-RS/-VB.
• Ensure Senershield-R/-RS/-VB and Sheathing Fabric are installed without voids.
• Apply Master Builders Solutions WS Flash over punched stud openings
TYPICAL ROUGH OPENING REINFORCEMENT WITH SHEATHING FABRIC
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
QUICK CORNER READY FOR INSTALLATION
EMBED QUICK CORNER IN SENERSHIELD-R/-RS/-VB
SECOND APPLICATION OF SENERSHIELD-R/-RS/-VB
TYPICAL QUICK CORNER APPLICATION
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• For more information, reference the Senershield Application Guidelines for Joint Treatment and Flashing Rough Openings on Framed Construction technical bulletin.
AWRB-05 2109
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-06 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Apply Master Builders Solutions WS Flash over punched stud openings.
• For more information, reference the Senershield Application Guidelines for Joint Treatment and Flashing Rough Openings on Framed Construction technical bulletin.
TYPICAL ROUGH OPENING CORNER TREATMENT WITH QUICK CORNERS AND SHEATHING FABRIC
1) APPLY SENERSHIELD-R/-RS/-VB TO ALL SHEATHING JOINTS
2) EMBED SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB AT SHEATHING JOINTS
1) APPLY SENERSHIELD-R/-RS/-VB TO ROUGH OPENING HEAD, SILL AND JAMBS
STEP 1
STEP 3
STEP 2
STEP 4
1) APPLY SENERSHIELD-R/-RS/-VB TO ALL ROUGH OPENING CORNERS
1) APPLY A SECOND COAT OF SENERSHIELD-R/-RS/-VB TO HEAD, SILL, JAMBS AND CORNERS WHEN APPLYING SENERSHIELD TO REST OF SHEATHING
2) EMBED QUICK CORNER IN SENERSHIELD-R/-RS/-VB AT ROUGH OPENING CORNERS
2) EMBED SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB AT ROUGH OPENING HEAD, SILL AND JAMBS
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-07 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• For more information, reference the Senershield Application Guidelines for Joint Treatment and Flashing Rough Openings on Framed Construction technical bulletin.
TYPICAL ROUGH OPENING CORNER TREATMENT WITH QUICK CORNERS AND MASTER BUILDERS SOLUTIONS WS FLASH
1) APPLY SENERSHIELD-R/-RS/-VB TO ALL SHEATHING JOINTS AND ROUGH OPENING CORNERS
2) EMBED SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB AT SHEATHING JOINTS
3) EMBED QUICK CORNER IN SENERSHIELD-R/-RS/-VB AT ROUGH OPENING CORNERS
1) APPLY MASTER BUILDERS SOLUTIONS WS FLASH TO ROUGH OPENING HEAD, SILL AND JAMBS
STEP 1
STEP 3
STEP 2
STEP 4
1) APPLY FLASHING PRIMER TO TO ROUGH OPENING CORNERS, HEAD, JAMBS, SILL AND SHEATHING AROUND ROUGH OPENING
1) APPLY SENERSHIELD-R/-RS/-VB TO HEAD, SILL, JAMBS AND CORNERS (COMPLETELY COAT MASTER BUILDERS SOLUTIONS WS FLASH) WHEN APPLYING SENERSHIELD TO REST OF SHEATHING
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*
SENERSHIELD-R/-RS/-VB
SHEATHING FABRIC
PIPE*STEP ONE
STEP TWO
AWRB-08 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Cut a square piece of Sheathing Fabric large enough to extend past the pipe by 2" in each direction.
• At the center of the square piece of Sheathing Fabric, pierce a small hole with a blade or scissors.
• With a blade or scissors, cut an “X”. Turn the square about 45° and cut another X. The center point of both “X”s will be the point you pierced previously.
• Insert the pipe through the newly cut square so it is centered with a minimum of2"oneachsidewiththecutflapspoint outward. The square should be flushwiththesheathing,SeeStep1.
• Embed the Sheathing Fabric in Senershield-R/-RS/-VB and coat the flapsaroundthepipe,SeeStep2.
• Wrap a 1" strip of Sheathing Fabric embedded in Senershield-R/-RS/-VB aroundtheflaps.
TYPICAL PENETRATION THROUGH WALL CONSTRUCTION (FABRIC ONLY)
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*
SPOT FASTENERS WITH SENERSHIELD-R/-RS/-VB
MAXFLASH OR SEALANT AT PERIMETER OF PENETRATION
PIPE*
SENERSHIELD-R/-RS/-VB
STEP ONE
STEP TWO
AWRB-09 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Senershield-R/-RS/-VB with Sheathing Fabric may be used as an alternate to provide an air/water-resistive barrier around penetrations.
• Provide backer rod and MasterSeal NP 150 or equal between pipe and cladding (by others).
TYPICAL PENETRATION THROUGH WALL CONSTRUCTION (WITH MAXFLASH OR SEALANT)
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*
POLYURETHANE FOAM*
PIPE*
SENERSHIELD-R/-RS/-VB
SHEATHING FABRIC
SHAVE CURED FOAM FLUSH WITH SHEATHING*
PIPE*
STEP ONE
STEP TWO
AWRB-10 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Ensure spray foam is low expansion. • Provide backer rod and MasterSeal NP
150 or equal between pipe and cladding (by others).
• Embed Master Builders Solutions Sheathing Fabric in Senershield-R/-RS/-VB.
TYPICAL PENETRATION THROUGH WALL CONSTRUCTION (ROUGH CUT)
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-11 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Senershield-R/-RS/-VB and Master Builders Solutions sheathing fabric may be used as an alternate to provide an air/water-resistive barrier at transition.
TYPICAL INSIDE CORNER CHANGE IN SUBSTRATE
FRAMING*
ACCEPTABLE SHEATHING*
MASTER BUILDERS SOLUTIONS WS FLASH W/ FLASHING PRIMER (AS REQUIRED)ACCEPTABLE SUBSTRATE*
SENERSHIELD-R/-RS/-VB
BRICK*
BACKER ROD AND SEALANT*
EIFS
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*
SENERSHIELD-R/-RS/-VB
MAXFLASH OR SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB
MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
THROUGH WALL FLASHING* INSIDE CORNER
THROUGH WALL FLASHING* WITH FLASHING PRIMER
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Apply a bead of MasterSeal NP 150 sealant between Through Wall Flashing Membrane and Inside Corner to create an airtight and watertight seal.
• Center Master Builders Solutions WS Flash so half of the width covers Through Wall Flashing and half covers the CMU substrate.
• A termination bar and MasterSeal NP 150 sealant can be used instead of Master Builders Solutions WS Flash (See AWRB-18).
• Lap Sheathing Fabric a minimum of 2" over Master Builders Solutions WS Flash.
• If using a termination bar, Sheathing Fabric must be beneath Through Wall Flashing* Membrane.
TYPICAL INSIDE CORNER
AWRB-12 2109
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*
SENERSHIELD-R/-RS/-VB
MAXFLASH OR SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB
MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
THROUGH WALL FLASHING* WITH FLASHING PRIMER
THROUGH WALL FLASHING* MEMBRANE DRIP EDGE IN A BED OF CONTINUOUS MASTERSEAL NP 150 SEALANT
THROUGH WALL FLASHING* OUTSIDE CORNER
AWRB-13 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Apply a bead of MasterSeal NP 150 sealant between Through Wall Flashing* and Outside Corner to create an airtight and watertight seal.
• Center Master Builders Solutions WS Flash so half of the width covers Through Wall Flashing* and half covers the gypsum sheathing.
• If using a termination bar, Master Builders Solutions Sheathing Fabric must be beneath Through Wall Flashing*.
TYPICAL OUTSIDE CORNER
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER OR EMBED SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VBSENERSHIELD-R/-RS/-VB
WINDOW FLANGE*
WINDOW*
EMBED SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB
AWRB-14 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Verify rough opening is properly treated prior to window installation. See AWRB-26 or AWRB-31.
• Do not block drainage at window sill. • Air seal to window by others.
TYPICAL WINDOW FLANGE TREATMENT
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*
SENERSHIELD-R/-RS/-VB
SHEATHING FABRIC
MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASHSENERSHIELD-R/-RS/-VB
FLASHING
SEALANT*
CONTINUOUS AIRSEAL*
WINDOW*
AWRB-15 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
•Provideenddamsatflashingterminations.
• If blocking is installed prior to Senershield-R/-RS/-VB application, it shall be treated as a rough opening; verify adhesion before proceeding.
• Embed Master Builders Solutions Sheathing Fabric in Senershield-R/-RS/-VB.
• Embed Master Builders Solutions Sheathing Fabric in Senershield-R/-RS/-VB, apply Master Builders Solutions WS Flash over Master Builders Solutions Flashing Primer, or MaxFlash at rough opening.
TYPICAL WINDOW HEAD
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASHCONTINUOUS AIRSEAL*
SENERSHIELD-R/-RS/-VB
WINDOW*
AWRB-16 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Apply Master Builders Solutions WS Flash over punched MaxFlash with 202 S/A mesh stud openings.
• If blocking is installed prior to Senershield-R/-RS/-VB application, it shall be treated as a rough opening; verify adhesion before proceeding.
• Embed Master Builders Solutions Sheathing Fabric in Senershield-R/-RS/-VB, apply Master Builders Solutions WS Flash over Master Builders Solutions Flashing Primer, or MaxFlash at rough opening.
• See AWRB-26 or AWRB-31.
TYPICAL WINDOW JAMB
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-17 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Install end/back dams as required. • If blocking is installed prior to
Senershield-R/-RS/-VB application, it shall be treated as a rough opening; verify adhesion before proceeding.
• Ifpanflashingisrequired,seedetailAWRB-11.
• Embed Master Builders Solutions Sheathing Fabric in Senershield-R/-RS/-VB, apply Master Builders Solutions WS Flash over Master Builders Solutions Flashing Primer, or MaxFlash at rough opening.
TYPICAL WINDOW SILL
WINDOW*
CONTINUOUS AIRSEAL*
SENERSHIELD-R/-RS/-VB
MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH
FRAMING*
ACCEPTABLE SHEATHING*
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-18 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Wrap rough opening in accordance with AWRB-26 or AWRB-31.
• Install MasterSeal NP 150 or equal as depicted onto the sill and jamb to maintain continuity of the air barrier.
• Installpanflashingintothewetsealant.Remove excess sealant as required.
• Install Master Builders Solutions Sheathing Fabric into wet Senershield-R/-RS/-VB at the jamb end dams.
TYPICAL PAN FLASHING
FRAMING*
ACCEPTABLE SHEATHING*
TREATED ROUGH OPENING
SENERSHIELD-R/-RS/-VB
PAN FLASHING*
MASTERSEAL NP 150 OR EQUAL*
FRAMING*
ACCEPTABLE SHEATHING*
TREATED ROUGH OPENING
MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH
PAN FLASHING*
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-19 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Ensure Senershield-R/-RS/-VB fully covers MaxFlash at overlap.
•ExtendflashingovercoatedMaxFlashon foundation.
• MaxFlash is used at foundation transition. Apply at 20–30 mils.
TYPICAL TERMINATION AT GRADE – SHEATHING OVERLAPPING FOUNDATION
FRAMING*
ACCEPTABLE SHEATHING*
EMBED SHEATHING FABRIC SENERSHIELD-R/-RS/-VB
SENERSHIELD-R/-RS/-VB
SHEATHING FABRIC
SENERSHIELD-R/-RS/-VB
MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
FLASHING*
BACKER ROD AND MASTERSEAL NP 150 OR EQUAL*
MASTERSEAL HLM 5000 OR EQUAL*
FOUNDATION*
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*
EMBED MASTER BUILDERS SOLUTIONS SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VBSENERSHIELD-R/-RS/-VB
EIFS
EMBED MASTER BUILDERS SOLUTIONS SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VBFLASHING*
MASTER BUILDERS SOLUTIONS WS FLASH W/ FLASHING PRIMER (AS REQUIRED)BACKER ROD AND SEALANT*FOUNDATION WATERPROOFING*
FOUNDATION*
AWRB-20 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Ensure Senershield-R/-RS/-VB fully covers Master Builders Solutions WS Flash at overlap.
•ExtendflashingovercoatedMasterBuilders Solutions WS Flash on foundation.
TYPICAL TERMINATION AT GRADE – SHEATHING OVERLAPPING FOUNDATION WITH EIFS
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-21 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Ensure Senershield-R/-RS/-VB fully covers Master Builders Solutions WS Flash at overlap.
•ExtendflashingovercoatedMasterBuilders Solutions WS Flash on foundation.
• Embed Master Builders Solutions MaxFlash or Master Builders Solutions Sheathing Fabric in Senershield-R/ -RS/-VB.
TYPICAL TERMINATION AT GRADE – SHEATHING FLUSH WITH FOUNDATION
FRAMING*
ACCEPTABLE SHEATHING*
SHEATHING FABRIC OR MAXFLASH
SENERSHIELD-R/-RS/-VB
SHEATHING FABRIC
SENERSHIELD-R/-RS/-VB
MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
FLASHING*MASTERSEAL NP 150 OR EQUAL*
MASTERSEAL HLM 5000 OR EQUAL*
FOUNDATION*
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-22 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Ensure Senershield-R/-RS/-VB fully covers Master Builders Solutions WS Flash at overlap.
•ExtendflashingovercoatedMasterBuilders Solutions WS Flash on foundation.
TYPICAL TERMINATION AT GRADE – SHEATHING FLUSH WITH FOUNDATION AND EIFS
FRAMING*
ACCEPTABLE SHEATHING*
EMBED MASTER BUILDERS SOLUTIONS SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VBSENERSHIELD-R/-RS/-VB
EIFS
SENERSHIELD-R/-RS/-VB
EMBED MASTER BUILDERS SOLUTIONS SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VBMASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER (AS REQUIRED)FLASHING*FOUNDATION WATERPROOFING*
SEALANT*
FOUNDATION*
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*
EMBED MASTER BUILDERS SOLUTIONS SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VB OR MAXFLASH
SIDING*
SENERSHIELD-R/-RS/-VB
EMBED MASTER BUILDERS SOLUTIONS SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VBFLASHING*MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
BACKER ROD AND SEALANT*FOUNDATION WATERPROOFING*FOUNDATION*
AWRB-23 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Ensure Senershield-R/-RS/-VB fully covers Master Builders Solutions WS Flash at overlap.
•ExtendflashingovercoatedMasterBuilders Solutions WS Flash on foundation.
• Contact siding manufacturer for installation instructions.
TYPICAL TERMINATION AT GRADE – SHEATHING OVERLAPPING FOUNDATION WITH SIDING
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*EMBED MASTER BUILDERS SOLUTIONS SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VB
SENERSHIELD-R/-RS/-VB
SIDING*
EMBED MASTER BUILDERS SOLUTIONS SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VBFLASHING*MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
SEALANT*FOUNDATION WATERPROOFING*FOUNDATION*
AWRB-24 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Ensure Senershield-R/-RS/-VB fully covers Master Builders Solutions WS Flash at overlap.
•ExtendflashingovercoatedMasterBuilders Solutions WS Flash on foundation.
• Contact siding manufacturer for installation instructions.
TYPICAL TERMINATION AT GRADE – SHEATHING FLUSH WITH FOUNDATION AND SIDING
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-25 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
TYPICAL EIFS ABUTMENT TO SIDING
FRAMING*
ACCEPTABLE SHEATHING*
EMBED SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VB OR MAXFLASH
EIFS
EMBED SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VB
TRIM BOARD*
FLASHING*
SIDING*
SEALANT*
SENERSHIELD-R/-RS/-VB
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-26 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Ensure Senershield-R/-RS/-VB fully covers Master Builders Solutions WS Flash at overlap.
TYPICAL TERMINATION AT GRADE – MASONRY VENEER
FRAMING*
ACCEPTABLE SHEATHING*
EMBED SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VB OR MAXFLASH
PERMALATH 1000
MORTAR SCRATCH COAT*
MORTAR SETTING BED*
MASONRY VENEER*
SENERSHIELD-R/-RS/-VB
EMBED SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VB OR MAXFLASH
MINIMUM GRADE D BUILDING PAPER OR AS REQUIRED BY CODE*
WEEP SCREED*
MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
FOUNDATION WATERPROOFING*
FOUNDATION*
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-27 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
TYPICAL EIFS ABUTMENT TO MASONRY VENEER
FRAMING*
ACCEPTABLE SHEATHING*
EMBED SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VB OR MAXFLASH
EIFS
SENERSHIELD-R/-RS/-VB
EMBED SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VB
FLASHING*
BACKER ROD AND SEALANT*
MASONRY VENEER WATER TABLE*
SUPPORT ANGLE*
MASONRY VENEER*
MORTAR SETTING BED*
MORTAR SCRATCH COAT*
PERMALATH 1000
MINIMUM GRADE D BUILDING PAPER OR AS REQUIRED BY CODE OR PER MASONRY VENEER MANUFACTURER*
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-28 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Seal brick tie with MaxFlash, embedding Master Builders Solutions Sheathing Fabric in Senershield-R/-RS/-VB, or Master Builders Solutions WS Flash with Flashing Primer.
• Consult the brick tie manufacturer for proper attachment.
TYPICAL BRICK ANCHOR (INSTALLED PRIOR TO AWRB APPLICATION)
FRAMING*
SENERSHIELD-R/-RS/-VB
MAXFLASH, MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER OR EMBED SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB
BRICK TIE*
ACCEPTABLE SHEATHING*
STEP TWO
STEP THREE
STEP ONE
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-29 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• For more information, see Senershield Fastener Self-Sealing technical bulletin.
• Consult the brick anchor manufacturer for proper attachment.
• Additional Senershield-R/-RS/-VB, MaxFlash or sealant may be post applied at anchor points.
• Option 3: Apply Master Builders Solutions WS Flash to Senershield-R/-RS/-VB prior to application of brick anchor.
TYPICAL BRICK ANCHOR (INSTALLED AFTER AWRB APPLICATION)
FRAMING*
SENERSHIELD-R/-RS/-VB
BRICK ANCHOR*
BRICK TIE*
BRICK ANCHOR*OPTION ONE
OPTION TWO
OPTION THREE
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-30 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• See detail AWRB-21 for typical brick anchor treatment.
TYPICAL BRICK EXPANSION JOINT
FRAMING*
ACCEPTABLE SHEATHING*MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
BRICK TIE*MASTER BUILDERS SOLUTIONS WS FLASHSENERSHIELD-R/-RS/-VBBACKER ROD AND SEALANT*BRICK*
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*
SENERSHIELD-R/-RS/-VB
BRICK ANCHOR*
EMBED SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VB OR MAXFLASH
SENERSHIELD-R/-RS/-VB
EMBED SHEATHING FABRIC WITH SENERSHIELD-R/-RS/-VB OR MAXFLASH
WEEPS*
FLASHING*
GROUT SOLID*
MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
FOUNDATION WATERPROOFING*FOUNDATION*
AWRB-31 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Ensure Senershield-R/-RS/-VB fully covers Master Builders Solutions WS Flash at overlap.
TYPICAL TERMINATION AT GRADE – BRICK
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
ACCEPTABLE SHEATHING*MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
CONTINUOUS INSULATION*
THROUGH WALL FLASHING* MEMBRANE
SENERSHIELD-R/-RS/-VB
BRICK*
WEEPS*MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
MASTERSEAL NP 150 OR EQUAL*
GROUT SOLID*
MASTERSEAL HLM 5000 HIGH BUILD SYSTEM OR EQUAL*
FOUNDATION*
AWRB-32 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Air space between sheathing and brick per design (not shown).
•Extendflashingverticallyupthebackingto 8" (203 mm) minimum height.
TYPICAL TERMINATION AT FOUNDATION INCORPORATING SHEATHING FABRIC WITH THROUGH WALL FLASHING – BRICK
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-33 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Air space between sheathing and brick per design (not shown).
•Extendflashingverticallyupthebackingto 8" (203 mm) minimum height.
TYPICAL TERMINATION AT FOUNDATION INCORPORATING TERMINATION BAR WITH THROUGH WALL FLASHING – BRICK
MASTERSEAL NP 150 OR EQUAL*
ACCEPTABLE SHEATHING*
TERMINATION BAR*
CONTINUOUS INSULATION*
THROUGH WALL FLASHING* MEMBRANE
FLASHING PRIMER
SENERSHIELD-R/-RS/-VB
BRICK*
WEEPS*
GROUT SOLID*
MASTERSEAL NP 150 OR EQUAL*
MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
MASTERSEAL HLM 5000 HIGH BUILD SYSTEM OR EQUAL*FOUNDATION*
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*
EMBED SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB OR MAXFLASH
SENERSHIELD-R/-RS/-VB
EIFS
EMBED SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB OR MAXFLASH
FLASHING*
BACKER ROD AND SEALANT*
BRICK*
MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
SENERSHIELD-R/-RS/-VB
AWRB-34 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Ensure Senershield-R/-RS/-VB fully covers Master Builders Solutions WS Flashatfloorline.
•ProvidesufficientslackintheMasterBuilders Solutions WS Flash at expansion joint to allow for movement.
TYPICAL EIFS ABUTMENT TO BRICK WITH DRAINAGE AT FLOORLINE
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-35 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Ensure drainage plane is continuous (unblocked);otherwiseinstallflashingwith drainage provision as show in Detail AWRB-34.
TYPICAL EIFS ABUTMENT TO BRICK
FRAMING*
ACCEPTABLE SHEATHING*
EMBED SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB OR MAXFLASH
EIFS
SENERSHIELD-R/-RS/-VB
BRICK*
BACKER ROD AND SEALANT*
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-36 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Embed Master Builders Solutions Sheathing Fabric in Senershield-R/-RS/-VB.
• Center Master Builders Solutions WS Flash so half of the width covers Through Wall Flashing* and half covers the primed substrate.
• Through Wall Flashing* can be folded to create an end dam. Ensure that seams are sealed with MasterSeal NP 150.
TYPICAL THROUGH WALL FLASHING AT HEAD – BRICK
SHEATHING FABRIC
ACCEPTABLE SHEATHING OVER FRAMING*
SENERSHIELD-R/-RS/-VB
THROUGH WALL FLASHING*
MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER OR MAXFLASH TO OVERLAP THROUGH WALL FLASHING
WEEPS*
THROUGH WALL FLASHING* END DAM SET IN MASTERSEAL NP 150 OR EQUAL
LINTEL*
WINDOW*
BRICK*
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*
2 MASTER BUILDERS SOLUTIONS QUICK CORNERS
MASTER BUILDERS SOLUTIONS SHEATHING FABRIC
FRAMING*
SENERSHIELD-R/-RS/-VB
AWRB-37 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Embed Master Builders Solutions Quick Corner in Senershield-R/-RS/-VB.
• Embed Master Builders Solutions Sheathing Fabric in Senershield-R/-RS/ -VB.
• Two Quick Corners are used, one on each side of the saddle.
TYPICAL SADDLE APPLICATION INCORPORATING SHEATHING FABRIC
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
FRAMING*
ACCEPTABLE SHEATHING*
MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
FRAMING*
SENERSHIELD-R/-RS/-VB
AWRB-38 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• All Master Builders Solutions WS Flash overlaps shall be primed with Master Builders Solutions Flashing Primer.
TYPICAL SADDLE APPLICATION INCORPORATING MASTER BUILDERS SOLUTIONS WS FLASH
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-39 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Ensure Senershield-R/-RS/-VB fully covers Master Builders Solutions WS Flash.
• Where Master Builders Solutions WS Flashisinstalledovertheflashing,ensure termination occurs a minimum of 2” above the roof.
TYPICAL KICK-OUT FLASHING
ACCEPTABLE SHEATHING*
SENERSHIELD-R/-RS/-VB
MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
ROOF FELT*
MASTER BUILDERS SOLUTIONS MAXFLASH, MASTER BUILDERS SOLUTIONS SHEATHING FABRIC EMBEDDED IN SENERSHIELD-R/-RS/-VB, OR MASTER BUILDERS SOLUTIONS WS FLASH WITH FLASHING PRIMER
STEP FLASHING*ROOF SHINGLES*
KICK-OUT FLASHING*GUTTER*
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-40 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• MaxFlash and Master Builders Solutions WS Flash may be used as an alternate to provide an air/water-resistive barrier at transition of sheathing to blocking.
• Ensure continuity of air barrier is maintained.
• Avoid solvent-based adhesives/primers whereroofinglapsSenershield-R/-RS/ -VB.
TYPICAL ROOF EDGE FLASHING
BLOCKING*
SHEATHING FABRIC, MASTER BUILDERS SOLUTIONS WS FLASH, OR MASTER BUILDERS SOLUTIONS MAXFLASH
LAP AND SEAL ROOF MEMBRANE AIR BARRIER* ONTO SENERSHIELD-R/-RS/-VB
CONTINUOUS CLEAT*
METAL ROOF EDGE*
MASTERSEAL NP 150 OR EQUAL BETWEEN ROOF EDGE AND CLADDING*
SENERSHIELD-R/-RS/-VB
ACCEPTABLE SHEATHING*
FRAMING*
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
EXTERIOR PLYWOOD*
FRAMING*
LAP AND SEAL ROOF MEMBRANE AIR BARRIER ONTO SENERSHIELD-R/-RS/-VB
METAL FASCIA*
CONTINUOUS CLEAT*
SEALANT BETWEEN METAL COPING AND CLADDING*
EMBED SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB
SENERSHIELD-R/-RS/-VB
ACCEPTABLE SHEATHING*
FRAMING*
AWRB-41 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Master Builders Solutions WS Flash may be used as an alternate to provide an air/water-resistive barrier at transition of sheathing to blocking.
TYPICAL ROOF EDGE FLASHING
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
This detail represents Master Builders Solutions Construction Systems US, LLC (hereinafter Master Builders Solutions) latest recommendations. It is presented in good faith by Master Builders Solutions. The detail is subject to change without notice. Master Builders Solutions accepts no liability for the end use of the detail. For conditions not shown, consult Master Builders Solutions for review of specific detail.
(*NOTE: BY OTHERS)
Senershield-R/-RS/-VB
AWRB-42 2109
• Install Master Builders Solutions materials in accordance with current installation instructions.
• Unsatisfactory conditions shall be reported to the General Contractor and corrected before the application of Master Builders Solutions products.
• Master Builders Solutions WS Flash may be used as an alternate to provide an air/water-resistive barrier at transition of sheathing to blocking.
TYPICAL PARAPET CAP FLASHING
BLOCKING*
LAP AND SEAL ROOF MEMBRANE AIR BARRIER ONTO SENERSHIELD-R/-RS/-VB
CLEAT*
METAL COPING*
SEALANT BETWEEN METAL COPING AND CLADDING*
EMBED SHEATHING FABRIC IN SENERSHIELD-R/-RS/-VB
SENERSHIELD-R/-RS/-VB
ACCEPTABLE SHEATHING*
FRAMING*
WarrantyMaster Builders Solutions Construction Systems US, LLC (“Master Builders”) warrants this product to be free from manufacturing defects and to meet the technical properties on the current Technical Data Guide, if used as directed within shelf life. Satisfactory results depend not only on quality products but also upon many factors beyond our control. Master Builders MAKES NO OTHER WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO ITS PRODUCTS. The sole and exclusive remedy of Purchaser for any claim concerning this product, including but not limited to, claims alleging breach of warranty, negligence, strict liability or otherwise, is shipment to purchaser of product equal to the amount of product that fails to meet this warranty or refund of the original purchase price of product that fails to meet this warranty, at the sole option of Master Builders. Any claims concerning this product must be received in writing within one (1) year from the date of shipment and any claims not presented within that period are waived by Purchaser. Master Builders WILL NOT BE RESPONSIBLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFITS) OR PUNITIVE DAMAGES OF ANY KIND.
Purchaser must determine the suitability of the products for the intended use and assumes all risks and liabilities in connection therewith. This information and all further technical advice are based on Master Builders’ present knowledge and experience. However, Master Builders assumes no liability for providing such information and advice including the extent to which such information and advice may relate to existing third party intellectual property rights, especially patent rights, nor shall any legal relationship be created by or arise from the provision of such information and advice. Master Builders reserves the right to make any changes according to technological progress or further developments. The Purchaser of the Product(s) must test the product(s) for suitability for the intended application and purpose before proceeding with a full application of the product(s). Performance of the product described herein should be verified by testing and carried out by qualified experts.
For professional use only. Not for sale to or use by the general public.
Master Builders Solutions Construction Systems US, LLC 889 Valley Park Drive, Shakopee, MN 55379 Customer Service +1 (800) 433-9517 senergy.master-builders-solutions.com/en Technical Service +1 (800) 589-1336
For the most current version of this literature, please visit our website at senergy.master-builders-solutions.com/en.
© MBCC Group, rev 09/2021® registered trademark of a MBCC Group member in many countries of the world