fpbe w2 fingerprint reader ard-fpbew2-icresource.boschsecurity.com/documents/bioentry_w2... · fpbe...
TRANSCRIPT
FPBE W2 Fingerprint ReaderARD-FPBEW2-IC
en Installation Guide
FPBE W2 Fingerprint Reader Table of contents | en 3
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
Table of contents
1 Safety 42 Introduction 62.1 Components 62.2 Names and function of parts 82.3 Cables and Connectors 102.4 How to enroll a fingerprint 133 Installation 163.1 Fixing the bracket and the product 163.2 Power supply connection 203.3 Network connection - TCP/IP 213.4 Wiegand Connection 223.5 RS 485 Connection 233.6 Resetting Network Settings 244 Technical Data 254.1 Product Specifications 254.2 Dimensions 28
4 en | SafetyFPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
1 Safety
Observe the following instructions to use the product safely andprevent any risk of injury or property damage.
!
Warning!Risk of fire or electric shockDo not install the product in a place with direct sunlight,moisture, dust, or soot.Do not install the product in a place with heat from anelectric heater.Install the product in a dry place.Install the product in a place with no electromagneticinterference.Do not install or repair the product independently.Do not allow liquids such as water, beverages, or chemicalsget into the product.
!
Warning!Risk of explosionReplacing the RTC battery with an incorrect type of batterymay cause explosion. Discard the battery according to theappropriate regional or international waste regulations.
Notice!If the product has been damaged due to independentinstallation or repair of the product by the user, free A/Sservice will not be provided.
FPBE W2 Fingerprint Reader Safety | en 5
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
!
Caution!Product damage or physical injuryDo not install the power supply cable in a place wherepeople pass by.
Notice!Risk of product damage or malfunctionDo not install the product near a highly magnetic objectsuch as a magnet, TV, (especially CRT) monitor, or speaker.If installing the product outside where the product iscompletely exposed, install the product together with theenclosure.When installing a number of devices, allow a space betweenthe devices for installation.Do not drop the product or apply an impact to the product.Do not to contaminate or damage the fingerprint contactunit with a dirty hand or foreign substances.When cleaning the product, wipe the product with a softand dry cloth and no water, benzene or alcohol.
Notice!For further information on this productdownload the Installation Manual andfirmware at our website:http://www.boschsecurity.com.Go to Products > Access Control Systems > Readers andCards > Biometric readers.
6 en | IntroductionFPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
2 Introduction
2.1 Components
ARD-FPBEW2 Bracket
Ferrite Core(1 EA)
PVC anchor(2 EA)
Heat shrink
Star-shapedwrench
Fixing screw (2
EA)
FPBE W2 Fingerprint Reader Introduction | en 7
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
Drillingtemplate
OSS Manual SafetyInstructions
QuickInstallation
Guide
Notice!Components may vary according to the installationenvironment.
8 en | IntroductionFPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
2.2 Names and function of parts
Item Feature
1 LED lampIndicates the operational status of the product with the colorof the LED lamp.
2 RF card authentication unitReads RF cards for entering and exiting.
3 Fingerprint authentication unitReads fingerprints placed on it for entering and exiting.
FPBE W2 Fingerprint Reader Introduction | en 9
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
Item Feature
4 Network reset buttonResets the network configuration. For details, refer to theResetting Network Setting.
5 LED lamp for NetworkShows the status of the network connection.
6 Cable– Interface cable– Power cable– Ethernet connector
10 en | IntroductionFPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
2.3 Cables and Connectors
FPBE W2 Fingerprint Reader Introduction | en 11
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
PIN Name Color
1 WG Tamper NO Gray (White stripe)
2 WG Tamper COM Green (White stripe)
3 WG Tamper NC Orange (White stripe)
4 Not used Blue
Brown
5 Not used Red
Green
6 WG D0 Green
7 WG D1 White
8 WG GND Black
9 TTL IN1 (LED red) Brown
10 TTL IN0 (LED green) Purple
11PWR +VDC Red
12 Not used Pink
13 PWR GND Black (White stripe)
14 485 TRXN (RxTx-) Yellow (Black stripe)
15 485 TRXP (RxTx+) Blue (White stripe)
16 485 PAG White (Black stripe)
12 en | IntroductionFPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
17 ENET TXP White
18 ENET TXN Orange
19 ENET RXP Black
20 ENET RXN Yellow
FPBE W2 Fingerprint Reader Introduction | en 13
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
2.4 How to enroll a fingerprint
In order to improve the fingerprint authentication rate, register thefingerprint correctly. ARD-FPBEW2 can recognize a fingerprint even ifthe angle and position of a user's fingerprint input change. If youregister the fingerprint with attention to the following matters, theauthentication rate can be improved.
Selecting a finger for fingerprint input
– In preparation for the case that the fingerprint of a specific fingercannot be used, for example if the user is lifting a load with onehand or a finger gets hurt, up to 10 fingerprints for each user canbe registered.
– In the case of a user whose fingerprint cannot be recognized well,the authentication rate can be improved by enrolling the samefinger twice repeatedly.
– If a finger has a cut or the fingerprint is blurry, select another fingerfor the fingerprint.
14 en | IntroductionFPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
– It is recommended to use the index finger or the middle fingerwhen scanning the fingerprint. The authentication rate can bereduced if it is difficult to place another finger at the center offingerprint sensor accurately.
Fingerprint enroll method1. Place the finger with the fingerprint to be registered on the
fingerprint authentication unit and press the finger gently for betterauthentication.
2. After a beep sounds, scan the fingerprint of the registered fingeragain (scan the fingerprint of a finger to be registered twice).
Cautions for enrolling a fingerprintWhen a fingerprint is recognized, it is compared with the initiallyregistered fingerprint, so the initial fingerprint enroll is the mostimportant. Pay attention to the following matters when enrolling thefingerprint:1. Place the finger deep enough to contact with the sensor
completely.2. Place the center of the fingerprint in the center of the sensor.3. If a finger has a cut or the fingerprint is blurry, select another finger
for the fingerprint.4. Scan the fingerprint correctly without moving according to the
instruction on the screen.5. If you make the finger upright so that the contact area with the
sensor has decreased or the angle of finger has warped, fingerprintauthentication may not be performed.
FPBE W2 Fingerprint Reader Introduction | en 15
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
When the fingerprint recognition failsThe ARD-FPBEW2 can recognize a fingerprint regardless of a change ofseason or finger condition. However, the authentication rate may varyaccording to the external environment or fingerprint input method.If the fingerprint authentication cannot be done smoothly, it isrecommended to take the following measures:1. If the finger is smeared with water or sweat, dry off the finger and
then scan the finger.2. If the finger is too dry, blow your breath on the fingertips and then
scan the finger.3. If the finger has a cut, register the fingerprint of another finger.4. The initially registered fingerprint often may have not been scanned
correctly, so register the fingerprint again according to ‘Cautions forenrolling a fingerprint’.
16 en | InstallationFPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
3 Installation
3.1 Fixing the bracket and the product
– Determine the correct position to install the bracket using theprovided drilling template. Fix the bracket firmly using fixing screwsthrough the bracket to the position where ARD-FPBEW2 will beinstalled.
Notice!If installing the ARD-FPBEW2 on a concrete wall, drill holes,insert PVC anchors, and fix them with fixing screws.
FPBE W2 Fingerprint Reader Installation | en 17
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
18 en | InstallationFPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
Notice!To avoid RF interference, a minimum separation distancemust be maintained.
FPBE W2 Fingerprint Reader Installation | en 19
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
1. Install the ARD-FPBEW2 onto the fixed bracket.
2. Connect the ARD-FPBEW2 to the bracket by rotating the star-shaped fixing screw.
3. Fix the wall mount bracket on a wall using the wall mountingscrews.
4. Hook the FP reader on the wall mounting bracket.5. Fix FP reader on the wall mounting bracket using the star-shaped
screw.
20 en | InstallationFPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
3.2 Power supply connection
Notice!Use a power supply adaptor of DC 12 V (± 10%) with aminimum of 600 mA which has obtained the approval ofIEC/EN 60950-1. If you wish to connect and use anotherdevice to the power supply adaptor, you should use anadaptor with a current capacity which is the same or largerthan the total power consumption required for the terminaland another device.
FPBE W2 Fingerprint Reader Installation | en 21
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
3.3 Network connection - TCP/IP
LAN connection (connecting to a hub)You can connect the product to a hub using a general type CAT-5 cable(or higher).
LAN connection (connecting to a PC directly)The ARD-FPBEW2 has an automatic MDI/MDIX function so that it can beconnected to a PC directly using a normal straight type CAT-5 cable (orhigher), not a cross cable.
22 en | InstallationFPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
3.4 Wiegand Connection
FPBE W2 Fingerprint Reader Installation | en 23
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
3.5 RS 485 Connection
24 en | InstallationFPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
3.6 Resetting Network Settings
1. Turn the power on.2. Press the network reset button on the rear of device until the
device restart automatically.3. Connect the device with default values.
3.1 TCP/IP address: DHCP address assignment (If DHCP addressassignment is failed, 169.254.x.x will be set.)3.2 Server mode: Disabled3.3 RS-485: PC connection, 115200 bps
4. Change the TCP/IP address or RS-485 information.5. Turn the power off later on and then check the network setting is
properly.
FPBE W2 Fingerprint Reader Technical Data | en 25
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
4 Technical Data
4.1 Product Specifications
Category Feature Specification
Credential Biometric Fingerprint
RF Option 125 KHz EM/HID Proxy,13.56 MHz MIFARE/DESFire/DESFire EV1/iClass
RF read range * MIFARE/DESFire/EM/HID Proxy/iClass/ISO15693 : 50 mm,Felica: 30 mm
26 en | Technical DataFPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
General CPU 1.2 GHz Quad Core
Memory 2GB Flash + 256 MB RAM
LED Multi-color
Sound Multi-tone Buzzer
Operatingtemperature
-20°C - 50°C
Storage temperature -40°C - 70°C
Operating humidity 0% - 80%, non-condensing
Storage humidity 0% - 90%, non-condensing
Dimension (W x H xD)
50 mm x 172 mm x 43.5 mm(Bottom) / 38.2 mm (Top)
Weight Device: 251gBracket: 43g (Including washerand bolt)
IP rating IP67
IK rating IK09
Certificates CE, FCC, KC, RoHS, REACH,WEEE
FPBE W2 Fingerprint Reader Technical Data | en 27
Bosch Access Systems GmbH 2018-02 | ARD-FPBEW2-IC |
Fingerprint Image dimension 272 x 320 pixels
Image bit depth 8 bit, 256 grayscale
Resolution 500 dpi
Template SUPREMA / ISO 19794-2 / ANSI378
Extractor / Matcher MINEX certified and compliant
LFD Supported
Interface Ethernet Supported (10/100 Mbps, autoMDI/MDI-X)
RS-485 OSDP V2
Wiegand Supported
PoE IEEE802.3af
Tamper Supported
Electrical Power Voltage: DC 12 VCurrent: Max. 600 mA
Wiegand output VOH More than 4.8 V
Wiegand output VOL Less than 0.2 V
Wiegand output Pull-up resistance
Internally pulled up with 1 kΩ
* RF read range will vary depending on the installation environment.
28 en | Technical DataFPBE W2 Fingerprint
Reader
2018-02 | ARD-FPBEW2-IC | Bosch Access Systems GmbH
4.2 Dimensions
Dimensions in mm
Bosch Access Systems GmbHCharlottenburger Allee 5052068 AachenGermanywww.boschsecurity.com© Bosch Access Systems GmbH, 2018