fourneau chambertin- chateauneuf fontenay

Art Culinaire 17721 132nd Ave. NE Woodinville, WA 98072 425-481-7500 Fax: 425-481-8080

Fourneau

« Chambertin- Chateauneuf »

« Fontenay »

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS. Do not try to light any appliance. Do not touch any electrical switch. Do not use any phone in your building. Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions. If you cannot reach your gas supplier, call the fire

department. - Installation and service must be performed by a qualified

installer, service agency or the gas supplier. - In the Commonwealth of Massachusetts, the appliance must be

installed by a licensed plumber or gas fitter.

WARNING : If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

!WARNING ! THIS RANGE CAN TIP INJURY TO PERSONS COULD RESULT INSTALL ANTI-TIP DEVICE PACKED WITH RANGE SEE INSTALLATION INSTRUCTIONS

GENERAL MANUAL

CHAMBERTIN – CHATEAUNEUF - FONTENAY

of 55

1065 mm 41 15/16 ’’

940 mm 37’’

727.5 mm-28 5/8 ’’

800 mm-31 1/2 ’’

430 mm-16 15/16 ’’

34 mm 1 5/16 ’’

650 mm-25 9/16 ’’

671 mm-26 7/16 ’’

47 mm-1 7/8 ’’

510 mm-20 1/16 ’’

147 mm5 13/16 ’’

40 mm 1 9/16 ’’

Back space vent (A)

Fig. 2

Fontenay with hob option on right hand side

or without hob option

Fontenay with hob option or left hand side, or hob options on left and right

hand side

768 mm 30 1/4

399 mm 15 11/16 ’’

914 mm36’’

Fig. 1

789 mm31 1/16 ’’

669 mm 26 5/16 ’’ 20 mm

13/16 ’’

340 mm 13 3/8

1505 mm 59 1/4 ’’

708 mm-27 7/8 ’’

GENERAL MANUAL


of 55

768 mm 30 1/4

399 mm 15 11/16 ’’

Chateauneuf without hob option

Chateauneuf with hob option on left

hand side

914 mm 36’’

Fig. 4

Chateauneuf with electric oven 340 mm

13 3/8

Chateauneuf with gas oven

768 mm 30 1/4

399 mm 15 11/16 ’’

Chambertin with or without hob option on

right hand side

914 mm 36’’

Fig. 3

340 mm 13 3/8

Chambertin with electric oven

Chambertin with gas oven

1105 mm43 1/2

1105 mm43 1/2

GENERAL MANUAL


of 55

UF

F

SF

Fig. 5

FONTENAY

60 mm 2 3/8 ’’

440 mm17 5/16

750 mm29 9/16

460 mm18 1/8

Fontenay with gas oven Fontenay with

electric oven

F

SFT

Fig. 6

FONTENAY

60 mm 2 3/8 ’’

440 mm 17 5/16 ’’

750 mm29 9/16 ’’

460 mm18 1/8 ’’

Fontenay with gas oven

Fontenay with electric oven

Fig. 7 UF

F

SFCHATEAUNEUF

60 mm 2 3/8 ’’

440 mm17 5/16 ’’

350 mm13 3/4 ’’


Chateauneuf with electric oven

460 mm18 1/8 ’’

Note: To allow for warming oven door swing radius, cabinet depth must be a maximum of 24 ¾”, to within 3 ½” of range.

Note: To allow for warming oven door swing radius, cabinet depth must be a maximum of 24 ¾”, to within 3 ½” of range.

GENERAL MANUAL


of 55

Fig. 8I

SF

F

F CHAMBERTIN

60 mm 2 3/8 ’’

750 mm29 1/2 ’’

Chambertin with electric oven

Chambertin with gas oven

460 mm18 1/8 ’’

440 mm17 5/16 ’’

Fig. 9

CHATEAUNEUF

F

SFT

60 mm 2 3/8 ’’

440 mm17 5/16 ’’

350 mm13 3/4 ’’


460 mm18 1/8 ’’

Chateauneuf with electric oven

GENERAL MANUAL


of 55

Layout : Cook’s stoves consisting of a cooking surface above a 62 liter oven and one or two general purpose cabinets (depending on model) which can optionally be equipped with FONTENAY (Figures 1, 2, 5 & 6), CHAMBERTIN (Figures 2, 3 & 8) or CHATEAUNEUF (Figures 2, 4, 7 & 9) plate warmers. The work surfaces adjacent to the cooking surfaces are designed to accommodate one of the optional units in the LACANCHE range or to be used as a worktop.

Description : Enameled steel or stainless body panels AISI 430. Pressing cooking surface (stainless steel AISI 304) (Figure 5, 7 and 8). 3- or 4- burners of different size and power individually controlled by a safety valve. Electrical ignition. “TRADITION” model equipped with a 385 x 510 mm (15 5/32’’ x 20 5/64’’) heating plate (Figures 7 and 9).

Gas oven : Enameled sheet metal. Dimensions W x H x D : 530 mm (20.8’’) x 305 mm (12’’) x 460 mm (18.1’’). 4 shelf level with 62 mm spacing, 62 liters / 2.18 ft3. Heating provided by thermostatically controlled burner, thermocouple safety cut-outs. Electrical ignition.

Power supply : 120 / 240 VAC 60Hz.

Static electric oven (option) : Same dimensions as gas oven. Thermostatically controlled roof and base heating elements, safety cut-out by safety thermostat.

Rating : 3400 W – Power supply : 240 Volts 60Hz.

Ventilated electric oven (option) Heating provided by two circular heating elements each surrounding a reaction-type fan. Dimensions W x H x D : 530 mm (20.8’’) x 305 mm (12’’) x 405 mm (15.9’’). This can optionally be fitted with an electric. Thermostatically controlled heating elements, safety cut-out by safety thermostat.

Rating : 3700 W – Power supply : 240 Volts 60Hz. Plate warmer cabinet (option) Plate warmer-insulated stainless internal lining (AISI 304). Heating provided by 950 W heating element underneath base. Controlled by thermostat selector switch, 30 to 110 °C. Capacity : 72 plates, Ø 240 mm (9.5’’). Dimensions W x H x D : 325 mm (12.8’’) x 490 mm (19.3’’) x 530 mm (20.8’’). 5 shelf level with 68 mm (2.8’’).

Rating : 1030 W – Power supply : 240 Volts 60Hz

Accessories One drip tray, one shelf, one pastry tray per oven. General-purpose cabinet : 1 shelf. Plate warmer cabinet : 2 shelves.

Shipment-Packaging Unpack and check the appliance is in good condition. In case damage, note any reservations on the delivery note and confirm them within 48 hours by registered letter with confirmation of delivery to the carrier.

Appliance Width Depth Height mm Weight Gross/Net LG 1131 G 1250 mm / 49.2’’ 840 mm / 33.1’’ 1070 mm / 42.1’’ 140 kg / 160 kg – 310 / 355 lb LG 1531 G 1650 mm / 64.1’’ 840 mm / 33.1’’ 1070 mm / 42.1’’ 200 kg /180 kg – 445 / 400 lb

GENERAL MANUAL


of 55

Gas connection : 1/2” ID NPT (Sch 40) inlet, on male coupling (Figures 1, 3, 4, 5, 6, 7, 8 & 9). Sealant on all pipe joints must be resistive to LP gas.

If used, a flex gas line for the gas supply must be metal of at least 1/2” ID NPT approved by an approved certifying agency (A.G.A., C.G.A,. etc.) in compliance with ANSI Z21.41 and Z21.69. Never use a hose made of rubber or other synthetic material.

Gas supplying : Appliance gas supplying can be switched, please refer to rating plate and marking at the rear of the appliance.

Electrical connection : On terminal block at the rear of the appliance. Use flexible cord in accordance with standard N.E.C., AINSI/NEMA 70-1996 or latest edition (not cord provided) (Figures 1, 2, 3, 4, 5, 6, 7, 8 & 9).

Pressures and hourly consumption : Appliance gas supplying can be switched (table 1).

Table 1 PRESSURE 6’’ WC 10’’ WC

GAS Natural gas L.P.G. Burner Btu / hr Btu / hr Oven 13,000 13,000

Ultra fast (UF) Tradition (T) 18,000 17,000 Intensive (I) 13,000 13,000

Fast (F) 10,500 10,000 Semi fast (SF) 5,000 5,000

Semi fast

Fast

F

Ultra Fast

of 55

(This page intentionally left blank)

of 55

Fourneau

« Chambertin »

« Chateauneuf »

« Fontenay »

INSTALLER'S MANUAL

Appliances must be installed in a workmanlike manner in accordance with the instructions in this manual and locally

applicable regulations. In the Commonwealth of Massachusetts, the appliance must

be installed by a licensed plumber or gas fitter. This manual will be handed over to the user after

installation.

INSTALLER’S MANUAL


of 55

Cabinet preparation (FONTENAY) :

The range is a freestanding unit. If the unit is to be placed next to cabinets, the clearances shown in Figure 10a are required.

The top grate support must be 34 mm - 1 5/8’’ above the adjacent base cabinet countertop. Min clearances to combustibles :

2 3/4’’ (70 mm) from rear of range to wall. This requirement will be met when range is installed with factory supplied back spacer vent (or equivalent).

0’’ (0 mm) from sides below 36’’ (914 mm) height. 2’’ (50.8 mm) from sides above 36’’ (914 mm) height. Cabinets 13’’ (330 mm) deep may be installed above the range at least 30’’ above the plane of the cooking

surface. Use range only with factory supplied legs.

A B C D E F G H I (a) J K L M N O With right stainless steel worktop

mm 762 330 457 914 660 770 175 395 420 60 765 865 1510 51 660 ’’ 30 13 18 36 26 30 5/16 6 7/8 15 9/16 16 9/16 2 3/8 30 1/8 34 1/16 59 7/16 2 26

With right gas option A B C D E F G H I (b) J K L M N O

mm 762 330 457 914 660 770 175 395 20 60 765 865 1510 51 660 ’’ 30 13 18 36 26 30 5/16 6 7/8 15 9/16

13/16 2 3/8 30 1/8 34 1/16 59 7/16 2 26

Fig. 10a Gas connection Electrical connection

B

A

D

K

G

I b

C

J

E

F

HL

M

NN

O

I a

This diagram depicts the actual location of gas and electrical connections on the range. Place gas stub-out or electrical receptacle outside of this area in accordance with local regulations.



of 55

Cabinet preparation (Chambertin, Chateauneuf) :

A B C D E F G H I J K

mm 762 330 457 914 235 405 765 865 51 1110 660 ’’ 30 13 18 36 9 1/4 15 15/16 30 1/8 34 1/16 2 43 11/16 26

The range is a freestanding unit. If the unit is to be placed next to cabinets, the clearances shown in Figure 10b are required.

The top grate support must be 34 mm - 1 5/8’’ above the adjacent base cabinet countertop. Min clearances to combustibles :

2 3/4’’ (70 mm) from rear of range to wall. This requirement will be met when range is installed with factory supplied back spacer vent (or equivalent).

0’’ (0 mm) from sides below 36’’ (914 mm) height. 2’’ (50.8 mm) from sides above 36’’ (914 mm) height. Cabinets 13’’ (330 mm) deep may be installed above the range at least 30’’ above the plane of the cooking

surface. Use range only with factory supplied legs.

Fig. 10b

Gas connection

Electrical connection

BA

D GE

C

F

J

II

H

K



of 55

Before connection : Check : - Pipework is perfectly clean in order to prevent the injectors becoming blocked and malfunctioning of the magnetic heads. - The gas for which the appliance was set up: Rating plate and markings. - Cross-sectional area of gas supply pipework is compatible with the appliance’s thermal output. - Provide adequate air supply during use of the appliance.

Gas connection : Female coupling Ø 15/21, 1/2” ID NPT on A (Figure 11).

After connection : Check the manifold pressure on pressure connection Ø 15/21, 1/8” NPT on B (Figure 12).

Change of gas :

The appliance is designed to operate with the gases in Table 2.

Table 2 Country GAS Pressure (Pn) U.S. Natural gas 6’’ WC U.S. L.P. propane 10’’ WC

THE APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE LOCAL CODES OR National Fuel Gas Code, ANSI Z223.1 or latest edition.

In the Commonwealth of Massachusetts, the appliance must be installed by a licensed plumber or gas fitter.

Manual shut-off valve should be installed in an accessible location in the gas piping external to the appliance for the purpose of turning on or shutting off gas to the appliance.

Check local codes.

Must be installed under an exhaust hood. In the Commonwealth of Massachusetts, the exhaust hood must be equipped with an "interlock" system. Check local codes.

Do not install this unit near combustible walls, partitions, pieces of furniture, or decorative material unless these are covered with adequate thermal insulation of the noncombustible type.

Making sure the resulting installation meets fire regulations.

IMPORTANT

IMPORTANT

IMPORTANT

Fig. 11

A

Fig. 12

B



of 55

Remove the pan supports and burners. Unscrew the screw(s) C on burner UF or T (Figures 13 and 14). pull and raise the top after having loosened the 2 screws D (Fig. 15), wedge the cooking surface.

A pressure regulator (fig. 16) is located in the right rear corner under the hob, to gain access to the pressure regulator, remove the top.

The reversible cap is labeled either « LP » or « Nat » and is easily recognized by the raised center screw slot (for natural) or the center depth (for LP).

To change LP to Natural or vice versa, the seal screw in the regulator lid is unscrewed, reversed and reinstalled to convert from one setting to another (Figures 17 and 18).

Fig. 15

D

Convertible regulator

Fig. 17

L.P. propane Natural gas

Fig. 18

Figure 13C

Figure 14

C C

Fig. 16



of 55

In case of use with a gas other than that for which the appliance was initially set up, it is crucial to replace the orifices and modify the adjustments as defined below.

TOP BURNERS :

Orifice : Lift the air ring E. Replace the injectors F in accordance with Table 3 and Figure 19 (Ø in 1/100 mm). The side burner bodies are kept in place by a transversal bar (H, fig. 21). In order to take them out, unscrew screws I (fig. 22) then G (fig. 20).

Note : When one or more nozzles are changed, the sealing ring should be changed as well (see gas circuit diagram).

Adjustment of primary air :

Refit the burner bodies and burner caps in their respective recesses; adjust the air ring F of the burner in accordance with the Table 4 and Figure 19.

Note : Normal flames are bluish green except for natural gas flames which are violet.

Clé de 12 Wrench 12 (15/32)

Fig. 19

F

E


Fig. 20

G

I

Fig. 22


H

Fig. 21



of 55

Table 3 Burners SR R I UR

GAS Pressure Ø Natural gas 6" WC 0.90 1.30 1.45 1.70

L.P. propane 10" WC 0.65 0.90 1.05 1.20

Adjustment of reduced flowrate of surface burners (Figure 23) : After connection or change of gas, it is crucial to modify this adjustment. - Remove the control knob. Light the burner, adjust to minimum setting, and then use a small screwdriver to set the adjusting screw J.

Note : Flame is reduced to ¼ of its size in the minimum setting, the burner must remain lit when changing from maximum setting to minimum setting.

Refitting the cooking surface : When refitting the cooking surface, it is vital to tighten fastening screws (figures 13, 14 and 15). Failure to do so can cause distortion of the cooking surface.

OVEN BURNERS : Oven orifice : Remove the base, CAUTION: when refitting place the base underneath the groove on the fascia (Figures 24 and 25). Disconnect the connection piece; unscrew screw K on the orifice holder (Figure 26). Replace the orifice (Table 5).

Table 5 Ø

GAS Pressure Oven Natural gas 6" WC 1.40

L.P. propane 10" WC 0.95

Fig. 23

J

Fig. 25

Fig. 24

Table 4 Burners SF F I UF

GAS Pressure Opening in mm/ inches Natural gas 6" WC 2.5 / 1/8 2.5 / 1/8 max 7 / 1/4

L.P. propane 10" WC 3.5 / 1/8 6 / 1/4 max max



of 55

Adjustment of oven primary airflow : Remove the base, loosen the screw L that secures the air ring and then adjust (Table 6, Figure 27).

Table 6 Opening in mm /

inches GAS Pressure Oven

Natural gas 6" WC 4 / 3/16 L.P. propane 10" WC 6 / 1/4

Adjustment of oven selector :

Adjustment is VITAL after connection or any change of gas.

When the range is installed, be sure that this selector cartridge (Fig. 27 and 28) is turned all the way to the proper setting. Turn M clockwise to the stop for LP Gas; counterclockwise A to the stop for Natural Gas.

IT IS EXTREMELY IMPORTANT THAT THIS SELECTOR CARTRIDGE IS SET FOR THE GAS ON WHICH THE RANGE IS TO BE USED.

Fig. 26

K

Fig. 27

L

Fig. 28 M

LP

LP

N

Natural

LP N

Off

Fig. 29



of 55

ELECTRICITY

It is hazardous to put the appliance into service without connecting it to suitable ground.

No liability can be accepted for accidents resulting from non-compliance with this requirement or incorrect grounding. Connect the equipotential bonding terminal (N, Figure 30).

Before connection, check that the : Mains voltage is compatible with the appliance’s rated voltage and thermal output.

Connection :

- Use a 3-wire grounded cord rated for 13 A or 4-wire rated for 30 A 125 / 250 VAC, type SRD, SRDT, S, SO or ST.

- Where local Codes do not permit grounding through neutral, use a 4-wire power supply cord or “pigtail” kit. Cord must be agency approved for use with household ranges.

- Remove access door O (Figure.31, gas oven range) or P (Figures 32 and 33, gas and electric range).

- Remove cable clamp and loosen supply cord mounting screws on the terminal block. - Connect to terminal block in accordance with figure 35. - Secure the cable by means of cable clamp, item Q (Figure 34). - Refit access door

THE APPLIANCE WHEN INSTALLED, MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE WITH THE LOCAL CODES OR The National Electrical Code, ANSI/NFPA 70-1996 or latest edition.

ALL WORK ON OR REPAIR OF AN APPLIANCE MUST BE CARRIED OUT BY A QUALIFIED INSTALLER.

IMPORTANT

N

Fig. 30

O Fig 31

P

Fig 32



of 55

BACK SPACER VENT FITTING :

It is MANDATORY to mount the back spacer vent R supplied with the appliance (or equivalent) to the wall, this allows for ventilation and reduces the risk of heat damage.

Screw the 2 brackets S to the wall according to figures 36, 37 and 38 (screws not supplied), then fit the back spacer vent onto these brackets by using the washers and nuts supplied with the range.

STABILITY DEVICE INSTALLATION INSTRUCTIONS :

Screw the anti-tip bracket T to the wall according to figures 37 and 38 (screws not supplied). Remove the right-hand drawer; push the range against the wall until the anti-tip bracket screw goes through the back of the range. Through the drawer gap, screw the nut and its washer on the anti-tip bracket screw.

11 22 3 4 5

L1 N

120/240 V ; 3-Pole ; 4-wire

L2Fig. 35

Fig. 34

Q

Fig. 30 M



of 55

S

R

Figure 36

93 mm 3 5/8 ’’

60 mm 2 3/8 ’’

206 mm8 1/8 ’’

772 mm 30 3/8 ’’

735 mm28 15/16 ’’

719 mm28 5/16 ’’60 mm

2 3/8 ’’

319 mm12 9/16 ’’

Chambertin Chateauneuf Fontenay

319 mm12 9/16 ’’

535 mm21 1/16 ’’

535 mm21 1/16 ’’

Chambertin

Chateauneuf

Fontenay

Fig. 38

R

S S

T TT

Figure 37

70 mm 2 3/4 ’’

T

R



of 55

SERVICE INSTRUCTIONS : - Lubricating gas valve.

If the gas taps tends to stick slightly, you may follow this procedure : 1 - Shut off the valve and / or the main electrical supply of the unit. 2 - Take out the knob corresponding to the gas valve to be greased. 3 - Unscrew the head from the body of the burner valve. 4 - Grease the tap shaft (High temperature lubricant, for example : SILICAL GEL ™ BARBAHL). Caution! Any excess grease should be removed. Reverse operation 3 to 1 (in that order) to put valve and knob back on.

- LIMITING THERMOSTAT :

To access internal components, lift and secure top.

Press pushbutton item U (Figure 39) in order to

reset the limiting thermostat.

Note: ALWAYS IDENTIFY the reason why the thermostat tripped.

Fig. 39

U



of 55

GAS CIRCUIT DIAGRAM

Designation

Part number

Burner cap 1.5 kW 65.330005 Burner cap 3.0 kW 65.330006 Burner cap 4.0 kW 65.330007 Burner cap 5.0 kW 65.330008

Burner bowl 1.5 kW 65.640003 Burner bowl 3.0 kW 65.640004 Burner bowl 4.0 kW 65.640005 Burner bowl 5.0 kW 65.640006

Air Shutter 65.080005 Mixing tube (1.5-3.0-4.0 & 5.0 kW) 65.064007

Injector holder 65.033018 Sealing ring 65.430007

Injector Dia. 65 65.14964 Injector Dia. 90 65.14969 Injector Dia. 95 65.14970

Injector Dia. 105 65.52863 Injector Dia. 120 65.14973 Injector Dia. 130 65.14974 Injector Dia. 140 65.14975 Injector Dia. 145 65.27781 Injector Dia. 170 65.30546

Brass knob (Gas model) 65.044013 Chrome knob (Gas model) 65.044014 Brass knob (Elec. model) 65.044015

Chrome knob (Elec. model) 65.044016 Gas valve 65.103021

GST Thermostat 65.224004 GSS Safety 65.224005

GSP Pilot Spark 65.103.022 Regulator 65.103023

Oven burner assy. 88.265400



of 55

65.330008

65.330005

65.103023

65. 430007

65.222002

65.103021

65.224004 65.222003

65.224005

80.903277

65.103022

65.226003

65.226006

65.080005

1.5 kW = 65.064007 3.0 kW = 65.064007 5.0 kW = 65.064007

65.033018

65.330006

65.103021

65.224004



of 55

65. 430007

65.222002

65.103021

65.224004 65.222003

65.224005

88.265400

65.103022

65.226003

65.226006

65.080005

1.5 kW = 65.064007 3.0 kW = 65.064007 4.0 kW = 65.064007

65.03301865.103023

65.103021

65.224004

65.330005

65.330007

65.330006



of 55

ELECTRIC CIRCUIT DIAGRAMS

LG 1531 G LG 1541 G

LG 1531 E LG 1541 GE

LG 1531 CT LG 1541 CT

LG 1531 CT LG 1541 CT

+ grill

ETL 001

Item n° Designation

Part number

TL Three pole limiting thermostat

65.39942 65.39942 65.39942

TH Oven thermostat 65.53670 65.53670 65.53670 28195 KM Contactor 65.223001 65.223001 65.223001

S Valve switch 65.222002 65.222002 65.222002 65.222002 28979 S1 Thermostat switch 65.222003 65.222003 65.222003 65.222003

S2 Thermostat switch 65.52194 65.52194 65.52194 A Spark Module (3+1

reign.) 65.226005 65.226005 65.226005 65.226005

A1 Spark Module (2) 65.226002 65.226002 65.226002 65.226002 B Top burner electrode 65.226006 65.226006 65.226006 65.226006

B1 Oven electrode 65.226003 X Terminal block 65.51922 65.51785 65.51785 65.51785 51922 R Bake element oven 65.30624 30624

R1 Broil element oven 65.35970 65.35970 R2 Convection element 65.39168 65.39168 M Convection Fan Motor 65.260001 65.260001 H Red Lamp 65.37606 65.37606 65.37606 65.37606 37606

H1 Orange Lamp 65.37607 65.37607 65.37607



of 55

H

L2L1

N

S1 (oven)S

120 V 60 Hz

240 V 60 Hz

A

B1

B

HT6548

UL / LG-LCF 1531 GRéf. S001009 – 00

1

2

3

G

N

M

R

C

L

Reig



of 55

H

L2L1

N

HTN 4

L 5

S1 (oven)S

120 V 60 Hz

240 V 60 Hz

A

A1

B1

B

B

S

HT6548

UL / LG 1541 GRéf. S001008 – 00

1

2

3

G

N

M

R

C

L

Reig



of 55

H

240 V 60 Hz120 V 60 Hz

L2

N

L1

4

3

1

2

5

TH

H1

TL

31 3221 2211 12

KM

KMA2

H

R1

A1

UL / LG-LCF 1541 ERéf. S001010 – 00

HTN 4

L 5

HTN 4

L 5

A1

A1

S

B

B

R1

R

R

S2P2

P1

P3

N. B : For the model LG/LCF 1531E, the ignition connector which is not used is connected to earth.



of 55

H

240 V 60 Hz120 V 60 Hz

L2

N

L1

TH

H1

TL

31 3221 2211 12

KM

KM

M

M

KMA2

H

HTN 4

L 5

HTN 4

L 5

S

A1

A1B

B

S2

A1

R2

R2

4

3

1

2

5

P2

P1

P3

UL / LG 1541 CTRéf. S001011 – 00

N. B : For the model LG/LCF 1531CT, the ignition connector which is not used is connected to earth.



of 55

H

240 V 60 Hz120 V 60 Hz

L2

N

L1

P2

P1

P3

TH

H1

TL

31 3221 2211 12

KM

KM

M

M

R1

KMA2

H

S2

R2

R2

A1

4

3

1

2

5

UL / LG 1541 CT + GrillRéf. S001012 – 00

HTN 4

L 5

HTN 4

L 5

S

A1

A1B

B

N. B : For the model LG/LCF 1531CT + grill, the ignition connector which is not used is connected to earth.



of 55

240 V 60 Hz L2L1

120 V 60 Hz N

HTN 4

L 5

HT6548

1

2

3

G

N

M

R

C

L

Reig

UL / LG-LCF 1531 G + LAG 020 / 024 RRéf. S001028 – 00

S1 (oven)S

S

B1

B

B

H



of 55

240 V 60 Hz120 V 60 Hz N

31 3221 2211 12

KMA2 A1

HTN 4

L 5

HTN 4

L 5

HTN 4

L 5

S

S

S

H

THTL

S24

3

1

2

5

P2

P1

P3H

H1

KM

R1

R2

R2

R1

UL / LG 1531 E + LAG 020 / 024 RRéf. S001029 – 00

B

B

B




of 55

H

240 V 60 Hz120 V 60 Hz

L2

N

L1

TH

H1

TL

31 3221 2211 12

KM

KM

M

M

KMA2

H

HTN 4

L 5

HTN 4

L 5

SA1

A1B

B

S2

A1

R2

R2

4

3

1

2

5

P2

P1

P3

UL / LG 1531 CT + LAG 020 / 024 RRéf. S001030 – 00

HTN 4

L 5

S A1B

S




of 55

H

240 V 60 Hz120 V 60 Hz

L2

N

L1

P2

P1

P3

TH

H1

TL

31 3221 2211 12

KM

KM

M

M

R1

KMA2

H

S2

R2

R2

A1

4

3

1

2

5

UL / LG 1531 CT + Grill + LAG 020 / 024 RRéf. S001031– 00

HTN 4

L 5

HTN 4

L 5

S

A1

A1B

B

HTN 4

L 5

S

A1B

S




of 55

H

240 V 60 Hz L2L1

120 V 60 Hz N

UL / LAG 020-024 R - LG-LCF 1531 G / LAG 020-024 RRéf. S001032 – 00

S

S1 (oven)S

HT6548

B1

B

B

B

S

A

A1

A1

HTN 4

L 5

HTN 4

L 5

1

2

3

G

N

M

R

C

L

Reig

N. B : For the model LG 1541G, the ignition connector which is not used is connected to earth.



of 55

H

240 V 60 Hz L2L1

TH

H1

TL

31 3221 2211 12

KM R1

KMA2

H

R1

A1

120 V 60 Hz N

UL / LAG 020-024 R - LG-LCF 1531 E / LAG 020-024 RRéf. S001033 – 00

4

3

1

2

5

S2

R

R

S

B

B

SA1

A1

HTN 4

L 5

HTN 4

L 5

BSA1

HTN 4

L 5

BSA1

HTN 4

L 5




of 55

H

240 V 60 Hz L2L1

120 V 60 Hz N

UL / LAG 020-024 R - LG-LCF 1531 CT / LAG 020-024 RRéf. S001034 – 00

S

B

B

SA1

A1

HTN 4

L 5

HTN 4

L 5

BSA1

HTN 4

L 5

BSA1

HTN 4

L 5

TH

H1

TL

31 3221 2211 12

KM

KM

M

M

KMA2

H

S2

A1

R2

R2

4

3

1

2

5

P2

P1

P3




of 55

H

240 V 60 Hz L2L1

120 V 60 Hz N

UL / LAG 020-024 R - LG-LCF 1531 CT + grill/ LAG 020-024 RRéf. S001035 – 00

S

B

B

SA1

A1

HTN 4

L 5

HTN 4

L 5

BSA1

HTN 4

L 5

BSA1

HTN 4

L 5

P2

P1

P3

TH

H1

TL

31 3221 2211 12

KM KM

M

M

R1

KMA2

H

S2

R2

R2

A1

4

3

1

2

5




of 55

240 V 60 Hz

H

H1HP2

P1

1

L

TH

R

- ETL 001Réf. S001036 – 00

S

Hot cupboard

fourneau chambertin- chateauneuf fontenay

Documents