fms vue fluid management & tissue ...synthes.vo.llnwd.net/o16/llnwmb8/int mobile/synthes...a....
TRANSCRIPT
This publication is not intended for distribution in the USA.
PRODUCT INFORMATION
FMS VUE™ FLUID
MANAGEMENT & TISSUE DEBRIDEMENT SYSTEM
S H O U L D E R / K N E E / S M A L L J O I N T / H I P
Reusable Tubing Setup Guide
SUCTIONBLOOD STOP
HIGH PRESSURE
LOW PRESSURE
RUN
STOPSOLOSOLO
SHAVERSHAVERFLOW +
IRRI
GGAATTATAATA
ION SUCTION
FMS VUEFMS VUE
A. CONNECT INFLOW TUBING:
21
SUCTION
RUN
STOP SOLO
FILL
SUCTION
RUN
STOP SOLO
FILL
BLOOD STOP
HIGH PRESSURE
LOW PRESSURE
BLOOD STOP
HIGH PRESSURE
LOW PRESSURE
SHAVERFLOW +
SHAVERFLOW +
SUCTION
RUN
STOP SOLO
FILL
SUCTION
RUN
STOP SOLO
FILL
BLOOD STOP
HIGH PRESSURE
LOW PRESSURE
BLOOD STOP
HIGH PRESSURE
LOW PRESSURE
SHAVERFLOW +
SHAVERFLOW +
B. PRIME THE FMS VUE SYSTEM:
21
C. CONNECT INTERMEDIARY TUBING WITH ONE-WAY VALVE:
STERILE OPERATOR: Pass the one-way valve(blue end) to the nonsterile operator.
1 NONSTERILE OPERATOR: Immediately connect the inflow tubing below fill chamber.
2 Prime the intermediary tube by opening the clamp under the fill chamber.
1
2
1 Lift the door and position green autolock component in green autolock slot on the pump. Centre tubing around the roller and engage the tube fitting opposite autolock.
2 Close door and connect the pressure sensor quick connect tube to CPC port. Position fill chamber in the fill chamber bracket.
IRRI
GATION
IRRI
GATION
IRRI
GATATA
ION
INFLOW
SHAVER
OUTFLOW CANNULA
WASTE
1 Pierce saline bags, open tubing’s white clampsand press the Run/Stop pad to activate pump.
2 Press and hold Blue Fill Chamber button until salinereaches the warning label on the fill chamber.
INFLOW
SHAVER
OUTFLOW CANNULA
WASTE
SUCTION
IRR
IGAT
ION
SUCTIONBLOOD STOP
Mitek
INF
LOW
WA
STE
COLLECTIONBA
G
1 0 , 0 0 0 m l
9,0 0 0 m l
8,0 0 0 m l
7,0 0 0 m l
6,0 0 0 m l
5,0 0 0 m l
4,0 0 0 m l
3,0 0 0 m l
2,0 0 0 m l
1,0 0 0 m l
5 0 0 m l
SHAV
ER
OU
TFLO
W C
ANN
ULA
WASTE
FMS VUE
SUCTION
SUCTION
SUCTION
PUMP SHAVER
BLOOD STOP
HIGH PRESSURE
LOW PRESSURE
SHAVERFLOW +
RUN
STOP SOLO
SUCTIONBLOOD STOP
HIGH PRESSURE
LOW PRESSURE
SHAVERFLOW +
RUN
STOP SOLO
SUCTION
D. CONNECT OUTFLOW TUBING FOR INFLOW OUTFLOW MODE (DEFAULT MODE)
1 NONSTERILE OPERATOR: Turn pinch valve lever vertically. Lift the door and position orange autolock component in orange autolock slot on the pump. Centre tubing around the roller and engage the centre tube fitting opposite autolock.
2 Slide shaver and outflow tubing limbs into pinch valve slots. Turn the pinch valve lever horizontal.
21
STERILE OPERATOR: Pass only the tubing end labeled waste to the nonsterile operator.
WARNING: Initial pressure settings are based on experience and should be used only as guidelines.The surgeon is responsible for setting pressures appropriate to the surgical procedure.
Recommended Initial Pressure Settings
JointPressure Level with Tourniquet
Pressure Level without Tourniquet
Shoulder Joint N/A 110 mmHg
Acromioplasty N/A 110 mmHg
Knee Joint 70 mmHg 143 mmHg
Hemarthrosis 110 mmHg-130 mmHg 110 mmHg-130 mmHg
Wrist 70 mmHg 130 mmHg
Elbow, Ankle 90 mmHg 130 mmHg
Hip N/A 143 mmHg
INFLOW
SHAVER
OUTFLOW CANNULA
WASTE
ORDERING INFORMATION:
Description
284002
283573
283512
284610
284649
283551
281103
284508
281142
FMS VUE Fluid Management & Tissue Debridement System
Foot Pedal FMS VUE System
Micro Tornado Shaver Hand Piece
Outflow Tubing Without One-Way Valve
Outflow Tubing With One-Way Valve (Reusable Setup)
Remote Control FMS VUE System
Intermediary Tubing Without One-Way Valve
Inflow Tubing FMS VUE System
Intermediary Tubing With One-Way Valve (Reusable Setup)
Code
DePuy Mitek, Inc.325 Paramount Dr. Raynham, MA 02767USATel: +1 (800)382-4682
depuysynthes.com
0086
Johnson & Johnson Medical Ltd. PO BOX 1988Simpson ParkwayLivingstonWest LothianEH54 0ABUnited Kingdom
Incorporated and registered in Scotland under company number SC132162.
©DePuy Synthes Mitek Sports Medicine, a division of Johnson & Johnson Medical Limited. 2014. All rights reserved.
DSEM/MTK/0614/0075 Issued: 08/14
DePuy International Limited St. Anthony’s RoadBeestonLeedsWest YorkshireLS11 8DTUnited KingdomTel: +44 (0) 113 387 7800Fax: +44 (0) 113 387 7890
Limited Warranty and Disclaimer: DePuy Mitek, Inc. products are sold with a limited warranty to the original purchaser against defects in workmanship and materials. Any other express or implied warranties, including warranties of merchantability or fitness, are hereby disclaimed.
Not all products are currently available in all markets.
Third party trademarks used herein are trademarks of their respective owners.
This publication is not intended for distribution in the USA.
Medos International SÀRL Chemin-Blanc 38 2400 Le Locle Switzerland
0086