flexible shaft · pdf filer & d marine flexible shaft couplings manufacturer b/w, prm,...

4
Flexible Shaft Couplings For engines 5 to 1500 HP Reduces engine noise and vibration transmission Fail safe design Bolts between existing shaft flanges Requires no machining Simple to install Simple to periodically check alignment Wide range of stock Accepts propeller thrust Impervious to salt water, diesel and lubrication oils Fast installation time Electrical continuity available Worldwide availability Competitively priced R & D Marine has developed a wide range of competitively priced Flexible Couplings to fit all major installations. The R & D Flexible Couplings reduce engine noise, vibration transmission and are designed to accept propeller thrust, a separate thrust bearing and bulk head are not required. The couplings are made from a polyester elastomer which is not affected by salt water, diesel and lubrication fluids. If electrical continuity is required an earthing connector can be fitted in the centre of most Flexible Couplings. Installation is quick and easy as the R & D Coupling requires no machining and comes supplied with bolts to connect between the two existing shaft flanges. Checking alignment on installation and during service checks is quick and easy using the red cone headed bolt. Products are available ex-stock and worldwide through our distribution network.

Upload: haxuyen

Post on 06-Feb-2018

216 views

Category:

Documents


2 download

TRANSCRIPT

Page 1: Flexible Shaft · PDF fileR & D Marine Flexible Shaft Couplings Manufacturer B/W, PRM, ZF-Hurth, Technodrive Yanmar B/W, PRM, ZF-Hurth, Twin Disc B/W,PRM, ZF-Hurth Paragon Twin Disc

Flexible Shaft Couplings

• For engines 5 to 1500 HP

• Reduces engine noise and

vibration transmission

• Fail safe design

• Bolts between existing shaft

flanges

• Requires no machining

• Simple to install

• Simple to periodically check

alignment

• Wide range of stock

• Accepts propeller thrust

• Impervious to salt water,

diesel and lubrication oils

• Fast installation time

• Electrical continuity

available

• Worldwide availability

• Competitively priced

R & D Marine has developed a wide range of competitively priced FlexibleCouplings to fit all major installations.

The R & D Flexible Couplings reduce engine noise, vibration transmission andare designed to accept propeller thrust, a separate thrust bearing and bulk headare not required.

The couplings are made from a polyester elastomer which is not affected by saltwater, diesel and lubrication fluids.

If electrical continuity is required an earthing connector can be fitted in thecentre of most Flexible Couplings.

Installation is quick and easy as the R & D Coupling requires no machining andcomes supplied with bolts to connect between the two existing shaft flanges.

Checking alignment on installation and during service checks is quick and easyusing the red cone headed bolt.

Products are available ex-stock and worldwide through our distribution network.

Meadow WorksClothall RoadBaldockHertfordshireEnglandSG7 6PD

Contact Us By:Tel: +44 (0)1462 892391Fax: +44 (0)1462 896448Web Site: www.randdmarine.comE mail: [email protected]

EARTHING CONNECTORS

‘R & D Marine’ Earthing Connector consists of a silver impregnated rubber strip, which when fitted through the axis of the couplingbetween the two fail safe straps gives electrical continuity. R & D have sizes to fit most 910 series couplings.

INSTALLATION PROCEDURE FOR R&D EARTHING CONNECTORS

1. While carrying out the following procedure, ensure that the connector is not contaminated by grease or dirt. 2. Before fitting the coupling into the drive train, remove 2 off bolts holding one of the fail safe straps. 3. Remove the fail safe strap to uncover the hole in the centre of the coupling. 4. Roll up the earthing connector (lengthways)

as tight as possible.

5. Push into the hole previously uncovered by removing the strapas far as possible.

6. Replace the fail safe strap ensuring that the connector is notdamaged, replace 2 off bolts.

7. Fit the coupling as per the installation instructions.8. Check electrical continuity on installation and thereafter

at three to six month intervals.

To Suit Coupling910-021910-001, 002, 007, 013, 014, 019, 020, 028, 043910-004, 005910-003, 006, 009, 012, 036, 037, 044, 052910-017, 018, 025, 026910-029, 038, 039, 040, 057910-032, 033910-015, 016, 022, 024, 046, 048, 053910-030, 041, 042, 047, 051910-035, 045, 049, 050910-062

R & D Marine Earthing Connector Application Guide

9/16

INSTALLATION PROCEDURE FOR R & D MARINE COUPLINGS1. Roughly align engine and stern gear without flexible coupling i.e. only two rigid half couplings pushed together.2. Bolt “R & D Marine” coupling between the two rigid couplings. Tightening details as below.3. Check alignment of engine by placing feeler gauges between the RED CONE

HEADED BOLT and the rigid half coupling. Repeat for the SAME bolt at 90° intervals by rotating the shaft.

4. If the gap is the same in all four positions, the engine is accurately aligned. Recommended minimum to maximum gap difference: 0.25 mm / 0.010 inch.

5. Run installation to bring engine compartment to working temperature. Re-check torque settings.

Recommended tightening torque:M8 - 27 Nm 20 lbsft 3/8 UNF - 40 Nm 30 lbsft M10 - 61 Nm 45 lbsft 7/16 UNF - 81 Nm 60 lbsft M12 - 108 Nm 80 lbsft1/2 UNF - 100 Nm 75 lbsft 5/8 UNF - 210 Nm 155 lbsft M18 - 338 Nm 250 lbsft 3/4 UNF - 366 Nm 270 lbsft

Part No103-036103-037103-038103-039103-040103-041103-042103-043103-044103-047103-053

Size (mm)9 x 5711 x 5715 x 5717 x 5719 x 5723 x 5725 x 5715 x 7517 x 759 x 3019 x 75

Designs are subject to constant review andimprovement therefore we reserve the rightto amend any dimension or detail specified orillustrated in this publication without noticeand without incurring any obligation to providesuch modification to products previouslydelivered.

Check Gap

GearboxFlange

ShaftFlange

Page 2: Flexible Shaft · PDF fileR & D Marine Flexible Shaft Couplings Manufacturer B/W, PRM, ZF-Hurth, Technodrive Yanmar B/W, PRM, ZF-Hurth, Twin Disc B/W,PRM, ZF-Hurth Paragon Twin Disc

R & D Marine Flexible Shaft Couplings

Manufacturer

B/W, PRM, ZF-Hurth, TechnodriveYanmarB/W, PRM, ZF-Hurth, Twin DiscB/W,PRM, ZF-HurthParagonTwin Disc, ZF-HurthVolvoB/W, PRM, ZF-Hurth, VolvoYanmarBukhB/W, PRM, ZF-Hurth, TechnodriveSelf Change 350HDSelf Change 700HDTwin DiscPRMVolvoVolvoEnfield, SonicTwin DiscTwin DiscB/W, PRM, ZF-Hurth, Twin DiscTwin DiscZF W320 320ABukhB/W, ZF-Hurth, Volvo

B/W, PRM, ZF-Hurth, Twin DiscTwin Disc, ZF-HurthOpen Centre V Drive 52mm Bore

Twin DiscYanmarTaipeoungyang TK 250Twin DiscPRM

Dong-I DMT 170HLYanmarB/W, PRM, ZF-Hurth, Volvo

Allison M25Dong-I DMT 260HTwin Disc MG 5111 SCZF 325-1A Volvo FlangeTwin Disc 510A/5114ATwin Disc MG 521ListerDong-I DMT 150HOpen Centre V Drive 58mm BoreOpen Centre V Drive 52mm BoreB/W, Hurth, VolvoDong-I DMT 70T, 90T, 100TVolvoTMPOpen Cntre V Drive 52mm BoreDong-I DMT 140HOpen Centre V Drive 58mm BoreOpen Centre V Drive 67mm Bore

NoBolts

4464464444466664428866844866484466686448866 (8)108866644

6424666

Ref

X O

O X O

X O

O X O O X O X O

O X O O X O X O O X O O

O O X O

O # O

O O O O O

O O O O O X O

O O

O

#

Gearbox Flange Dimensions Flexible Coupling Details

Flexible Coupling Information

O These couplings are fitted with a shouldered bush to locate in the gearbox flange O These flexible couplings have been approved by BUREAU VERITASX These flexible couplings have been approved by LLOYDS REGISTER OF SHIPPING # For the Hurth HBW 150 V Gearbox an adaptor 202-351 is required (22.3 mm 0.875" long)

For the IRM 220A Gearbox, we can supply adapter plate 202-384 (54mm 2.125" long) and for the Twin Disc 502 Gearbox, adapter plate 202-148 (54mm 2.125" long) that bolt ontoflexible coupling 910-003, 910-025 or 910-032 and with half coupling 202-037 or 202-054, alternatively clamp type 202-176 or 202-178

HP x 0.7457 = KW KW x 1.341 = HP Couplings 910-030, 910-035, 910-041 and 910-045 will require suitable adaptors for the gearbox flange

Coupling Selection Guide

Capacity/100 rpmkW HP3.73 52.24 314.92 205.97 85.22 714.92 202.24 39.69 137.46 102.24 32.24 332.1 4348.47 6529.84 4029.84 402.24 33.73 51.87 2.548.47 6563.38 8520.88 2820.88 2848.47 653.73 514.92 2089.48 12027.6 3727.6 378.95 12119.3 1607.46 109.69 1341.0 5541.0 5541.0 55104.4 14067.0 903.73 55.97 8171.5 23048.47 6567.0 9048.47 6556 7563.38 8589.48 1207.46 1035.8 4817.9 245.2 7

18.64 2541.0 555.96 82.42 3.2514.16 1947.0 6323.8 3237.3 50

Length

mm Inch32.5 1.2832.5 1.2847.5 1.8735.6 1.4034.5 1.3547.5 1.8743.7 1.7245.0 1.7745.0 1.7732.5 1.2832.5 1.2844.5 1.7558.0 2.2860.7 2.3960.7 2.3932.5 1.2832.5 1.2841.7 1.6444.5 1.7556.7 2.2349.8 1.9649.8 1.9644.5 1.7532.5 1.2852.4 2.0658.4 2.3055.4 2.1855.4 2.1845.0 1.77108.0 4.2545.0 1.7751.1 2.0163.3 2.4963.3 2.4963.3 2.4958.4 2.3058.4 2.3032.5 1.2845.0 1.77108.0 4.2544.5 1.7558.4 2.3062.7 2.47124.0 4.88101.6 4.058.4 2.3069.9 2.7545.0 1.7747.5 1.8745.0 1.7752.4 2.0663.3 2.4935.6 1.4038.1 1.5052.6 2.0748.2 1.9055.5 2.18563.8 2.51

Diameter

mm Inch114.3 4.5114.3 4.5152.4 6.0114.3 4.5114.3 4.5152.4 6.0114.3 4.5143.0 5.63135.0 5.31114.3 4.5114.3 4.5222.2 8.75276.4 10.88190.5 7.5190.5 7.5114.3 4.5114.3 4.5108.0 4.25222.2 8.75276.4 10.88152.4 6.0152.4 6.0228.6 9.0114.3 4.5143.0 5.63292.1 11.5152.4 6.0152.4 6.0162.0 6.38348.0 13.7143.0 5.63143.0 5.63190.5 7.50190.5 7.50190.5 7.50292.1 11.5292.1 11.5114.3 4.5143.0 5.6348.0 13.7222.2 8.75292.1 11.5222.2 8.75223.0 8.78230.0 9.00260.4 11.25150.9 5.94222.2 8.75172.0 6.77162.0 6.38143.0 5.63190.5 7.50114.3 4.5112.8 4.44162.0 6.38210.0 8.27172.0 6.77230.0 9.06

Register

mm Inch63.5 2.5050.0 1.9776.2 3.0063.5 2.5066.7 2.6376.2 3.0060.0 2.3663.5 2.5065.0 2.5647.0 1.8563.5 2.50152.4 6.00152.4 6.0095.25 3.7595.25 3.7560.0 2.3660.0 2.36---- ----152.4 6.00127.0 5.0076.2 3.0076.2 3.00140 5.5147.0 1.8563.5 2.50152.4 6.0076.2 3.0076.2 3.0063.5 2.50152.4 6.0063.5 2.5063.5 2.50100 3.9495.25 3.7595.25 3.75152.4 6.00160.0 6.3050.0 1.9763.5 2.50152.4 6.00152.4 6.00150.0 5.90152.4 6.00140.0 5.51152.4 6.00152.4 6.0063.5 2.50140.0 5.5176.2 3.0063.5 2.5063.5 2.50100.0 3.9460.0 2.36---- ----63.5 2.50130.0 5.1276.2 3.0095.25 3.75

Bolt Pitch Circlemm Inch82.55 3.2578.00 3.07120.6 4.7582.55 3.2582.55 3.25120.6 4.7580.0 3.15107.9 4.25100.0 3.9374.5 2.9382.55 3.25190.5 7.50228.6 9.00152.4 6.00152.4 6.0080.0 3.1580.0 3.1576.0 3.00190.5 7.50222.2 8.75120.6 4.75120.6 4.75196 7.7274.5 2.93107.9 4.25247.6 9.75120.6 4.75120.6 4.75107.9 4.25295.3 11.63104.8 4.13107.9 4.25152.0 5.984152.4 6.00152.4 6.00247.6 9.75240.0 9.4578.0 3.07107.9 4.25295.3 11.63190.5 7.50240.0 9.45190.5 7.50170.0 6.69190.5 7.50241.3 9.5098.5 3.88180.0 7.09120.6 4.75107.9 4.25107.9 4.25152.0 5.98480.0 3.1581.0 3.19107.9 4.25170.0 6.69120.6 4.75152.4 6.00

Nom DiaOf Holesmm Inch10.0 0.3910.0 0.3912.7 0.5010.0 0.399.7 0.3816.0 0.6310.0 0.3911.2 0.4410.0 0.398.1 0.3210.0 0.3911.2 0.4416.0 0.6319.0 0.7516.0 0.6310.0 0.3910.0 0.3911.2 0.4422.6 0.8925.4 1.0012.7 0.516.0 0.6317.0 0.678.1 0.3211.2 0.4425.4 1.0012.7 0.516.0 0.6311.2 0.4425.4 1.0010.0 0.3912.3 0.4814.3 0.5619.0 0.7516.0 0.6325.4 1.0025.1 0.9810.0 0.3911.2 0.4425.4 1.0019.0 0.7521.0 0.82622.6 0.8918.0 0.7122.6 0.8919.0 0.7511.2 0.4420.0 0.7912.7 0.5011.2 0.4411.2 0.4416.0 0.6310.0 0.3911.2 0.4411.2 0.4416.0 0.6312.7 0.5016.0 0.63

Diameter

mm Inch101.6 4.00101.6 4.00146.0 5.75101.6 4.00101.6 4.00146.0 5.75101.6 4.00127.0 5.00127.0 5.0090.0 3.54101.6 4.00222.2 8.75260.4 10.25184.2 7.25184.2 7.25101.6 4.00101.6 4.00101.6 4.00228.6 9.00266.7 10.5146.0 5.75146.0 5.75225 8.8690.0 3.54127.0 5.00292.1 11.5146.0 5.75146.0 5.75127.0 5.00340.0 13.38127.0 5.00130.0 5.12178.0 7.00184.2 7.25184.2 7.25292.1 11.5287.2 11.3101.6 4.00127.0 5.00340.0 13.38228.6 9.00292.1 11.5228.6 9.00205.0 8.07230.0 9.00279.4 11.00120.7 4.75218 8.58146.0 5.75127.0 5.00127.0 5.00178.0 7.00101.6 4.00112.8 4.44127.0 5.00198.0 7.80146.0 5.75184.2 7.25

FlexibleCoupling

910-001910-002910-003910-004910-005910-006910-007910-009910-012910-013910-014910-015910-016910-017910-018910-019910-020910-021910-022910-024910-025910-026910-027910-028910-029910-030910-032910-033910-034910-035910-036910-037910-038910-039910-040910-041910-042910-043910-044910-045910-046910-047910-048910-049910-050910-051910-052910-053910-054910-055910-057910-058910-059910-060910-061910-062910-063910-064

BoltDia

M10

M10

1/2 UNF

M10

3/8 UNF

1/2 UNF

M10

7/16 UNF

M10

M8

M10

7/16 UNF

5/8 UNF

5/8 UNF

5/8 UNF

M10

M10

7/16 UNF

1/2 UNF

5/8 UNF

1/2 UNF1/2 UNF

1/2 UNF

M8

7/16 UNF

5/8 UNF

1/2 UNF

1/2 UNF

7/16 UNF

5/8 UNF

M10

7/16 UNF

M14

5/8 UNF

5/8 UNF

5/8 UNF

5/8 UNF

M10

7/16 UNF

3/4 UNF

1/2 UNF

5/8 UNF

1/2 UNF

M18

1/2 UNF

5/8 UNF

7/16 UNF

1/2 UNF

1/2 UNF

7/16 UNF

7/16 UNF

5/8 UNF

M10

7/16 UNF

7/16 UNF

M16

1/2 UNF

5/8 UNF

How to Select (details required)1. Engine horse power and Engine Speed2. Gearbox type and reduction ratio3. Gearbox flange details. Diameter of flange. Diameter of register. Pitch circle diameter of fixing holes. Size and quantity of holes

(Pitch circle diameter is the distance between the centre of hole at 12 O`clock position to the centre of the hole at 6 o`clock)

Example1. Ford 150 HP at 2500 RPM2. Borg Warner Velvet Drive 72C 2:1 Reduction3. 5” Flange, 2.500 dia Register, 4.250 PCD,

4 off holes 0.437 diameter

The R & D 910 Series couplings consist of a contoured flexible disc moulded in tough yet resilient new type Polyester Elastomer. The contoured disc givesclearance for bolt heads, and is able to flex freely to take up any temporary misalignment of the engine and shaft, due to flexing of the boat structure or theengine moving on its rubber vibration isolation mountings. Forward thrust is taken in compression on the disc between the two half couplings and reverse thrustis taken again in compression on the disc between the two fail safe straps. In the unlikely event of a disc failure, the steel straps make the coupling fail safe andensure drive is maintained in both forward and reverse.

Couplings as standard are non-conducting but we can supply a silver impregnated rubber element to fit in the centre of the coupling between the twofail safe straps to give continuity if required.

To calculate Power of coupling required.

Horse Power of Engine x Reduction Ratio x 100 = HP/100rpmEngine Speed

150 x 2 x 100 = 12 HP/100 rpm Coupling Required 910-009 Borg Warner2500

ALLISONM25 9" Flange 910-046

BORG WARNER4" Flange 910-001, 910-004, 910-01470C 71C500 100015005" Flange 910-009(BW) 910-029,

910-044(BW), 910-05771C 72C50006" Flange 910-003, 910-025, 910-03273C 7000

BUKH 4" Flange 910-013, 910-028

DONG IDMT 70T 178 mm Flange 910-058DMT 90TDMT 100TDMT 140H 198 mm Flange 910-062DMT 150H 218 mm Flange 910-053DMT 170HL 287 mm Flange 910-042DMT 260H 292 mm Flange 910-047

ENFIELD and SONIC DRIVES2 Bolt 910-021

LISTER4 1⁄2" Flange 910-052

NEWAGE PRM S= Shallow Case, D= Deep Case4" Flange 910-001, 910-004, 910-014Delta 80 120150 5" Flange 910-009(PR) 910-044(PR)101 910-029 140160260 6" Flange 910-003, 910-025, 910-032175 265301302310401402500750 601 3:11000 3:1 7 1⁄4" Flange 910-018, 910-040601 4:11000 4:1 1200S 1500S1750S 10 1⁄2" Flange 910-0241200D 1500D1750D

PARAGON4" Flange 910-005

SELF CHANGE GEARS8 3⁄4" Flange 910-015350HD10 3⁄4" Flange 910-016700

TAIPEOUNGYANG178 mm Flange 910-038TK250

TECHNODRIVE4” Flange 910-001, 910-004, 910-014TMC30 TMC40TMC50TMC60TM260 5" Flange 910-009(PR) 910-029 TM93 - needs spacer 202-560 910-044(PR)TM93ATM170TM170ATM345TM345ATM485ATM545ATM880A 6" Flange 910-006, 910-026, 910-033TM130BTM200B up to 1.28: 1 TM265TM265A 7 1⁄4" Flange 910-018TMC200B up to 4.48: 1TM1200A

TMP2 Bolt 910-0605" Flange 910-009(PR) 910-044(PR)12000

TWIN DISCSC= Shallow Case, DC= Deep Case4" Flange 910-001, 910-004, 910-014MG 340 MG 360MG5010SCMG5011SCMG5010V4 3⁄4" Flange Adaptor 202-148 with MG502-I 910-003, 910-025, 910-032MG502-V 5" Flange 4 1⁄8 PCD 910-036 MG5010A MG5011A 5" Flange 4 1⁄4 PCD 910-009(PR) 910-044(PR)MG5005A 910-029, 910-057MG5012SCMG5015AMG5020SCMG5055A 6" Flange 910-006, 910-026, 910-033MG5010DC MG5050MG5050-VMG5050-AMG5061SCMG5061-AMG5061VMG5062VMG506-1MG506A-1MG507-1MG507A-1MG5075IVMG5075-AMG5075SC 7 1⁄4" Flange 910-017, 910-039MG506DC MG5065AMG507-1MG507-1SCMG507-2SCMG507A-2MG5075A needs adaptor 202-356MG5075SCMG5075IV MG5081SCMG5081A needs adaptor 202-356MG5082AMG5082SCMG5085SC needs adaptor 202-356 MG5085A needs adaptor 202-356MG5090AMG509SCMG509UMG5091SCMG5095AMGX5095A

TWIN DISC cont`d9" Scalloped Flange 910-048MG5111SC MG5114SC 9" Flange 910-022, 910-050MG510SC MG510AMG5111AMG5114AMG5111V,MG5114VMG514CUMG514UMG5135A 10 1⁄2" Flange 910-024 MG5091DC MG509DCMG510DCMG5111DCMG5114DCMG5113MG514

VOLVO4" Flange 910-007 MS RB 4" Flange 910-019, 910-020, 910-059 MS 2 MS 10MS 15MS25 5" Flange 910-009(VO), 910-029MS 3 910-044(VO), 910-057 MS4MS5HS25AHS45AHS63A6" Flange 910-006, 910-026 HS80A 910-033

YANMAR (KANZAKI)4" Flange 78mm PCD 910-002 KBW10 910-043KM2KM3KM355" Flange 100mm PCD 910-012KBW20KBW21KM4KM4AKMH4A5 1⁄2"Flange 4 1⁄4 PCD 910-009, 910-029, 910-037KM40 910-057KM5KMH40AKMH41AKMH50KMH50AKMH51A6" Flange 910-006, 910-026, 910-033KMH6KMH60KMH61AKMH61V 910-063

ZF-HURTH4" Flange 910-001, 910-004, 910-014

ZF35 HBW 35 40 HBW 4M50 HBW 5M100 HBW 10M125H HSW 12125 HBW 12M150 HBW 15M150A HBW 15MA250 HBW 25M250H HSW 25250A HSW 25A

25MA30M

45A 1.25:1450D HSW 45C

ZF HURTH cont`d4 3⁄4 " Adaptor 202-384 with 910-003

910-025, 910-032ZF

220A-1 IRM 220A 225Az

5" Flange 910-009(PR), 910-029 910-044(PR), 910-057

HBW HSW ZF 360

450H2 450A2 45A450D 45C630H1 63630A1 63A630D 63C

88C90TS 90ATS 110TS

6" Flange 13.2 mm bolt holes 910-003,910-025, 910-032

ZF45-1 6" Flange 16.3mm bolt holes 910-006,

910-026, 910-033 HSW IRM ZF800A2 80A800A3 80-1A

85A220 needs adaptor

202-329280A280-1

280V-LD 280-1A 280PL 280IV

280 285A285IV286286A286IV300TS300-1TS300ATS 300-1ATS

301PL-2 301C301A-2 301A300VTS 300IVTS

110ATS110IVTS

7 1⁄4" Flange 910-017IRM3118" Flange 910-049IRM ZF 311PL 311

325-1A Volvo 335A

350PL-2 350350A-2 350A350PL-1350A-1

350 TS350 ATS

350V 350V350V-LD 350 IV

360A500A500-1A

8 3⁄4" Flange 910-027IRM ZF320-2 W320

320A

ZF-HURTH V DRIVE4" Flange Adaptor 202-351 withHSW ZF 910-034, 910-055, 910-061150V 15M IV5" Flange 910-034, 910-055, 910-061HSW ZF

90 IVTS630V 63 IV6" Flange 910- 054, 910-063HSW ZF

110 IVTS220V-2 220 IV800V 80 IV800V2 80-1IV7 1⁄4" Flange Adaptor 202-552 with

ZF 910-064302 IV

8" Flange 910-049ZF 325 IV350-IV370V500-1 IV

Page 3: Flexible Shaft · PDF fileR & D Marine Flexible Shaft Couplings Manufacturer B/W, PRM, ZF-Hurth, Technodrive Yanmar B/W, PRM, ZF-Hurth, Twin Disc B/W,PRM, ZF-Hurth Paragon Twin Disc

R & D Marine Flexible Shaft Couplings

Manufacturer

B/W, PRM, ZF-Hurth, TechnodriveYanmarB/W, PRM, ZF-Hurth, Twin DiscB/W,PRM, ZF-HurthParagonTwin Disc, ZF-HurthVolvoB/W, PRM, ZF-Hurth, VolvoYanmarBukhB/W, PRM, ZF-Hurth, TechnodriveSelf Change 350HDSelf Change 700HDTwin DiscPRMVolvoVolvoEnfield, SonicTwin DiscTwin DiscB/W, PRM, ZF-Hurth, Twin DiscTwin DiscZF W320 320ABukhB/W, ZF-Hurth, Volvo

B/W, PRM, ZF-Hurth, Twin DiscTwin Disc, ZF-HurthOpen Centre V Drive 52mm Bore

Twin DiscYanmarTaipeoungyang TK 250Twin DiscPRM

Dong-I DMT 170HLYanmarB/W, PRM, ZF-Hurth, Volvo

Allison M25Dong-I DMT 260HTwin Disc MG 5111 SCZF 325-1A Volvo FlangeTwin Disc 510A/5114ATwin Disc MG 521ListerDong-I DMT 150HOpen Centre V Drive 58mm BoreOpen Centre V Drive 52mm BoreB/W, Hurth, VolvoDong-I DMT 70T, 90T, 100TVolvoTMPOpen Cntre V Drive 52mm BoreDong-I DMT 140HOpen Centre V Drive 58mm BoreOpen Centre V Drive 67mm Bore

NoBolts

4464464444466664428866844866484466686448866 (8)108866644

6424666

Ref

X O

O X O

X O

O X O O X O X O

O X O O X O X O O X O O

O O X O

O # O

O O O O O

O O O O O X O

O O

O

#

Gearbox Flange Dimensions Flexible Coupling Details

Flexible Coupling Information

O These couplings are fitted with a shouldered bush to locate in the gearbox flange O These flexible couplings have been approved by BUREAU VERITASX These flexible couplings have been approved by LLOYDS REGISTER OF SHIPPING # For the Hurth HBW 150 V Gearbox an adaptor 202-351 is required (22.3 mm 0.875" long)

For the IRM 220A Gearbox, we can supply adapter plate 202-384 (54mm 2.125" long) and for the Twin Disc 502 Gearbox, adapter plate 202-148 (54mm 2.125" long) that bolt ontoflexible coupling 910-003, 910-025 or 910-032 and with half coupling 202-037 or 202-054, alternatively clamp type 202-176 or 202-178

HP x 0.7457 = KW KW x 1.341 = HP Couplings 910-030, 910-035, 910-041 and 910-045 will require suitable adaptors for the gearbox flange

Coupling Selection Guide

Capacity/100 rpmkW HP3.73 52.24 314.92 205.97 85.22 714.92 202.24 39.69 137.46 102.24 32.24 332.1 4348.47 6529.84 4029.84 402.24 33.73 51.87 2.548.47 6563.38 8520.88 2820.88 2848.47 653.73 514.92 2089.48 12027.6 3727.6 378.95 12119.3 1607.46 109.69 1341.0 5541.0 5541.0 55104.4 14067.0 903.73 55.97 8171.5 23048.47 6567.0 9048.47 6556 7563.38 8589.48 1207.46 1035.8 4817.9 245.2 7

18.64 2541.0 555.96 82.42 3.2514.16 1947.0 6323.8 3237.3 50

Length

mm Inch32.5 1.2832.5 1.2847.5 1.8735.6 1.4034.5 1.3547.5 1.8743.7 1.7245.0 1.7745.0 1.7732.5 1.2832.5 1.2844.5 1.7558.0 2.2860.7 2.3960.7 2.3932.5 1.2832.5 1.2841.7 1.6444.5 1.7556.7 2.2349.8 1.9649.8 1.9644.5 1.7532.5 1.2852.4 2.0658.4 2.3055.4 2.1855.4 2.1845.0 1.77108.0 4.2545.0 1.7751.1 2.0163.3 2.4963.3 2.4963.3 2.4958.4 2.3058.4 2.3032.5 1.2845.0 1.77108.0 4.2544.5 1.7558.4 2.3062.7 2.47124.0 4.88101.6 4.058.4 2.3069.9 2.7545.0 1.7747.5 1.8745.0 1.7752.4 2.0663.3 2.4935.6 1.4038.1 1.5052.6 2.0748.2 1.9055.5 2.18563.8 2.51

Diameter

mm Inch114.3 4.5114.3 4.5152.4 6.0114.3 4.5114.3 4.5152.4 6.0114.3 4.5143.0 5.63135.0 5.31114.3 4.5114.3 4.5222.2 8.75276.4 10.88190.5 7.5190.5 7.5114.3 4.5114.3 4.5108.0 4.25222.2 8.75276.4 10.88152.4 6.0152.4 6.0228.6 9.0114.3 4.5143.0 5.63292.1 11.5152.4 6.0152.4 6.0162.0 6.38348.0 13.7143.0 5.63143.0 5.63190.5 7.50190.5 7.50190.5 7.50292.1 11.5292.1 11.5114.3 4.5143.0 5.6348.0 13.7222.2 8.75292.1 11.5222.2 8.75223.0 8.78230.0 9.00260.4 11.25150.9 5.94222.2 8.75172.0 6.77162.0 6.38143.0 5.63190.5 7.50114.3 4.5112.8 4.44162.0 6.38210.0 8.27172.0 6.77230.0 9.06

Register

mm Inch63.5 2.5050.0 1.9776.2 3.0063.5 2.5066.7 2.6376.2 3.0060.0 2.3663.5 2.5065.0 2.5647.0 1.8563.5 2.50152.4 6.00152.4 6.0095.25 3.7595.25 3.7560.0 2.3660.0 2.36---- ----152.4 6.00127.0 5.0076.2 3.0076.2 3.00140 5.5147.0 1.8563.5 2.50152.4 6.0076.2 3.0076.2 3.0063.5 2.50152.4 6.0063.5 2.5063.5 2.50100 3.9495.25 3.7595.25 3.75152.4 6.00160.0 6.3050.0 1.9763.5 2.50152.4 6.00152.4 6.00150.0 5.90152.4 6.00140.0 5.51152.4 6.00152.4 6.0063.5 2.50140.0 5.5176.2 3.0063.5 2.5063.5 2.50100.0 3.9460.0 2.36---- ----63.5 2.50130.0 5.1276.2 3.0095.25 3.75

Bolt Pitch Circlemm Inch82.55 3.2578.00 3.07120.6 4.7582.55 3.2582.55 3.25120.6 4.7580.0 3.15107.9 4.25100.0 3.9374.5 2.9382.55 3.25190.5 7.50228.6 9.00152.4 6.00152.4 6.0080.0 3.1580.0 3.1576.0 3.00190.5 7.50222.2 8.75120.6 4.75120.6 4.75196 7.7274.5 2.93107.9 4.25247.6 9.75120.6 4.75120.6 4.75107.9 4.25295.3 11.63104.8 4.13107.9 4.25152.0 5.984152.4 6.00152.4 6.00247.6 9.75240.0 9.4578.0 3.07107.9 4.25295.3 11.63190.5 7.50240.0 9.45190.5 7.50170.0 6.69190.5 7.50241.3 9.5098.5 3.88180.0 7.09120.6 4.75107.9 4.25107.9 4.25152.0 5.98480.0 3.1581.0 3.19107.9 4.25170.0 6.69120.6 4.75152.4 6.00

Nom DiaOf Holesmm Inch10.0 0.3910.0 0.3912.7 0.5010.0 0.399.7 0.3816.0 0.6310.0 0.3911.2 0.4410.0 0.398.1 0.3210.0 0.3911.2 0.4416.0 0.6319.0 0.7516.0 0.6310.0 0.3910.0 0.3911.2 0.4422.6 0.8925.4 1.0012.7 0.516.0 0.6317.0 0.678.1 0.3211.2 0.4425.4 1.0012.7 0.516.0 0.6311.2 0.4425.4 1.0010.0 0.3912.3 0.4814.3 0.5619.0 0.7516.0 0.6325.4 1.0025.1 0.9810.0 0.3911.2 0.4425.4 1.0019.0 0.7521.0 0.82622.6 0.8918.0 0.7122.6 0.8919.0 0.7511.2 0.4420.0 0.7912.7 0.5011.2 0.4411.2 0.4416.0 0.6310.0 0.3911.2 0.4411.2 0.4416.0 0.6312.7 0.5016.0 0.63

Diameter

mm Inch101.6 4.00101.6 4.00146.0 5.75101.6 4.00101.6 4.00146.0 5.75101.6 4.00127.0 5.00127.0 5.0090.0 3.54101.6 4.00222.2 8.75260.4 10.25184.2 7.25184.2 7.25101.6 4.00101.6 4.00101.6 4.00228.6 9.00266.7 10.5146.0 5.75146.0 5.75225 8.8690.0 3.54127.0 5.00292.1 11.5146.0 5.75146.0 5.75127.0 5.00340.0 13.38127.0 5.00130.0 5.12178.0 7.00184.2 7.25184.2 7.25292.1 11.5287.2 11.3101.6 4.00127.0 5.00340.0 13.38228.6 9.00292.1 11.5228.6 9.00205.0 8.07230.0 9.00279.4 11.00120.7 4.75218 8.58146.0 5.75127.0 5.00127.0 5.00178.0 7.00101.6 4.00112.8 4.44127.0 5.00198.0 7.80146.0 5.75184.2 7.25

FlexibleCoupling

910-001910-002910-003910-004910-005910-006910-007910-009910-012910-013910-014910-015910-016910-017910-018910-019910-020910-021910-022910-024910-025910-026910-027910-028910-029910-030910-032910-033910-034910-035910-036910-037910-038910-039910-040910-041910-042910-043910-044910-045910-046910-047910-048910-049910-050910-051910-052910-053910-054910-055910-057910-058910-059910-060910-061910-062910-063910-064

BoltDia

M10

M10

1/2 UNF

M10

3/8 UNF

1/2 UNF

M10

7/16 UNF

M10

M8

M10

7/16 UNF

5/8 UNF

5/8 UNF

5/8 UNF

M10

M10

7/16 UNF

1/2 UNF

5/8 UNF

1/2 UNF1/2 UNF

1/2 UNF

M8

7/16 UNF

5/8 UNF

1/2 UNF

1/2 UNF

7/16 UNF

5/8 UNF

M10

7/16 UNF

M14

5/8 UNF

5/8 UNF

5/8 UNF

5/8 UNF

M10

7/16 UNF

3/4 UNF

1/2 UNF

5/8 UNF

1/2 UNF

M18

1/2 UNF

5/8 UNF

7/16 UNF

1/2 UNF

1/2 UNF

7/16 UNF

7/16 UNF

5/8 UNF

M10

7/16 UNF

7/16 UNF

M16

1/2 UNF

5/8 UNF

How to Select (details required)1. Engine horse power and Engine Speed2. Gearbox type and reduction ratio3. Gearbox flange details. Diameter of flange. Diameter of register. Pitch circle diameter of fixing holes. Size and quantity of holes

(Pitch circle diameter is the distance between the centre of hole at 12 O`clock position to the centre of the hole at 6 o`clock)

Example1. Ford 150 HP at 2500 RPM2. Borg Warner Velvet Drive 72C 2:1 Reduction3. 5” Flange, 2.500 dia Register, 4.250 PCD,

4 off holes 0.437 diameter

The R & D 910 Series couplings consist of a contoured flexible disc moulded in tough yet resilient new type Polyester Elastomer. The contoured disc givesclearance for bolt heads, and is able to flex freely to take up any temporary misalignment of the engine and shaft, due to flexing of the boat structure or theengine moving on its rubber vibration isolation mountings. Forward thrust is taken in compression on the disc between the two half couplings and reverse thrustis taken again in compression on the disc between the two fail safe straps. In the unlikely event of a disc failure, the steel straps make the coupling fail safe andensure drive is maintained in both forward and reverse.

Couplings as standard are non-conducting but we can supply a silver impregnated rubber element to fit in the centre of the coupling between the twofail safe straps to give continuity if required.

To calculate Power of coupling required.

Horse Power of Engine x Reduction Ratio x 100 = HP/100rpmEngine Speed

150 x 2 x 100 = 12 HP/100 rpm Coupling Required 910-009 Borg Warner2500

ALLISONM25 9" Flange 910-046

BORG WARNER4" Flange 910-001, 910-004, 910-01470C 71C500 100015005" Flange 910-009(BW) 910-029,

910-044(BW), 910-05771C 72C50006" Flange 910-003, 910-025, 910-03273C 7000

BUKH 4" Flange 910-013, 910-028

DONG IDMT 70T 178 mm Flange 910-058DMT 90TDMT 100TDMT 140H 198 mm Flange 910-062DMT 150H 218 mm Flange 910-053DMT 170HL 287 mm Flange 910-042DMT 260H 292 mm Flange 910-047

ENFIELD and SONIC DRIVES2 Bolt 910-021

LISTER4 1⁄2" Flange 910-052

NEWAGE PRM S= Shallow Case, D= Deep Case4" Flange 910-001, 910-004, 910-014Delta 80 120150 5" Flange 910-009(PR) 910-044(PR)101 910-029 140160260 6" Flange 910-003, 910-025, 910-032175 265301302310401402500750 601 3:11000 3:1 7 1⁄4" Flange 910-018, 910-040601 4:11000 4:1 1200S 1500S1750S 10 1⁄2" Flange 910-0241200D 1500D1750D

PARAGON4" Flange 910-005

SELF CHANGE GEARS8 3⁄4" Flange 910-015350HD10 3⁄4" Flange 910-016700

TAIPEOUNGYANG178 mm Flange 910-038TK250

TECHNODRIVE4” Flange 910-001, 910-004, 910-014TMC30 TMC40TMC50TMC60TM260 5" Flange 910-009(PR) 910-029 TM93 - needs spacer 202-560 910-044(PR)TM93ATM170TM170ATM345TM345ATM485ATM545ATM880A 6" Flange 910-006, 910-026, 910-033TM130BTM200B up to 1.28: 1 TM265TM265A 7 1⁄4" Flange 910-018TMC200B up to 4.48: 1TM1200A

TMP2 Bolt 910-0605" Flange 910-009(PR) 910-044(PR)12000

TWIN DISCSC= Shallow Case, DC= Deep Case4" Flange 910-001, 910-004, 910-014MG 340 MG 360MG5010SCMG5011SCMG5010V4 3⁄4" Flange Adaptor 202-148 with MG502-I 910-003, 910-025, 910-032MG502-V 5" Flange 4 1⁄8 PCD 910-036 MG5010A MG5011A 5" Flange 4 1⁄4 PCD 910-009(PR) 910-044(PR)MG5005A 910-029, 910-057MG5012SCMG5015AMG5020SCMG5055A 6" Flange 910-006, 910-026, 910-033MG5010DC MG5050MG5050-VMG5050-AMG5061SCMG5061-AMG5061VMG5062VMG506-1MG506A-1MG507-1MG507A-1MG5075IVMG5075-AMG5075SC 7 1⁄4" Flange 910-017, 910-039MG506DC MG5065AMG507-1MG507-1SCMG507-2SCMG507A-2MG5075A needs adaptor 202-356MG5075SCMG5075IV MG5081SCMG5081A needs adaptor 202-356MG5082AMG5082SCMG5085SC needs adaptor 202-356 MG5085A needs adaptor 202-356MG5090AMG509SCMG509UMG5091SCMG5095AMGX5095A

TWIN DISC cont`d9" Scalloped Flange 910-048MG5111SC MG5114SC 9" Flange 910-022, 910-050MG510SC MG510AMG5111AMG5114AMG5111V,MG5114VMG514CUMG514UMG5135A 10 1⁄2" Flange 910-024 MG5091DC MG509DCMG510DCMG5111DCMG5114DCMG5113MG514

VOLVO4" Flange 910-007 MS RB 4" Flange 910-019, 910-020, 910-059 MS 2 MS 10MS 15MS25 5" Flange 910-009(VO), 910-029MS 3 910-044(VO), 910-057 MS4MS5HS25AHS45AHS63A6" Flange 910-006, 910-026 HS80A 910-033

YANMAR (KANZAKI)4" Flange 78mm PCD 910-002 KBW10 910-043KM2KM3KM355" Flange 100mm PCD 910-012KBW20KBW21KM4KM4AKMH4A5 1⁄2"Flange 4 1⁄4 PCD 910-009, 910-029, 910-037KM40 910-057KM5KMH40AKMH41AKMH50KMH50AKMH51A6" Flange 910-006, 910-026, 910-033KMH6KMH60KMH61AKMH61V 910-063

ZF-HURTH4" Flange 910-001, 910-004, 910-014

ZF35 HBW 35 40 HBW 4M50 HBW 5M100 HBW 10M125H HSW 12125 HBW 12M150 HBW 15M150A HBW 15MA250 HBW 25M250H HSW 25250A HSW 25A

25MA30M

45A 1.25:1450D HSW 45C

ZF HURTH cont`d4 3⁄4 " Adaptor 202-384 with 910-003

910-025, 910-032ZF

220A-1 IRM 220A 225Az

5" Flange 910-009(PR), 910-029 910-044(PR), 910-057

HBW HSW ZF 360

450H2 450A2 45A450D 45C630H1 63630A1 63A630D 63C

88C90TS 90ATS 110TS

6" Flange 13.2 mm bolt holes 910-003,910-025, 910-032

ZF45-1 6" Flange 16.3mm bolt holes 910-006,

910-026, 910-033 HSW IRM ZF800A2 80A800A3 80-1A

85A220 needs adaptor

202-329280A280-1

280V-LD 280-1A 280PL 280IV

280 285A285IV286286A286IV300TS300-1TS300ATS 300-1ATS

301PL-2 301C301A-2 301A300VTS 300IVTS

110ATS110IVTS

7 1⁄4" Flange 910-017IRM3118" Flange 910-049IRM ZF 311PL 311

325-1A Volvo 335A

350PL-2 350350A-2 350A350PL-1350A-1

350 TS350 ATS

350V 350V350V-LD 350 IV

360A500A500-1A

8 3⁄4" Flange 910-027IRM ZF320-2 W320

320A

ZF-HURTH V DRIVE4" Flange Adaptor 202-351 withHSW ZF 910-034, 910-055, 910-061150V 15M IV5" Flange 910-034, 910-055, 910-061HSW ZF

90 IVTS630V 63 IV6" Flange 910- 054, 910-063HSW ZF

110 IVTS220V-2 220 IV800V 80 IV800V2 80-1IV7 1⁄4" Flange Adaptor 202-552 with

ZF 910-064302 IV

8" Flange 910-049ZF 325 IV350-IV370V500-1 IV

Page 4: Flexible Shaft · PDF fileR & D Marine Flexible Shaft Couplings Manufacturer B/W, PRM, ZF-Hurth, Technodrive Yanmar B/W, PRM, ZF-Hurth, Twin Disc B/W,PRM, ZF-Hurth Paragon Twin Disc

Flexible Shaft Couplings

• For engines 5 to 1500 HP

• Reduces engine noise and

vibration transmission

• Fail safe design

• Bolts between existing shaft

flanges

• Requires no machining

• Simple to install

• Simple to periodically check

alignment

• Wide range of stock

• Accepts propeller thrust

• Impervious to salt water,

diesel and lubrication oils

• Fast installation time

• Electrical continuity

available

• Worldwide availability

• Competitively priced

R & D Marine has developed a wide range of competitively priced FlexibleCouplings to fit all major installations.

The R & D Flexible Couplings reduce engine noise, vibration transmission andare designed to accept propeller thrust, a separate thrust bearing and bulk headare not required.

The couplings are made from a polyester elastomer which is not affected by saltwater, diesel and lubrication fluids.

If electrical continuity is required an earthing connector can be fitted in thecentre of most Flexible Couplings.

Installation is quick and easy as the R & D Coupling requires no machining andcomes supplied with bolts to connect between the two existing shaft flanges.

Checking alignment on installation and during service checks is quick and easyusing the red cone headed bolt.

Products are available ex-stock and worldwide through our distribution network.

Meadow WorksClothall RoadBaldockHertfordshireEnglandSG7 6PD

Contact Us By:Tel: +44 (0)1462 892391Fax: +44 (0)1462 896448Web Site: www.randdmarine.comE mail: [email protected]

EARTHING CONNECTORS

‘R & D Marine’ Earthing Connector consists of a silver impregnated rubber strip, which when fitted through the axis of the couplingbetween the two fail safe straps gives electrical continuity. R & D have sizes to fit most 910 series couplings.

INSTALLATION PROCEDURE FOR R&D EARTHING CONNECTORS

1. While carrying out the following procedure, ensure that the connector is not contaminated by grease or dirt. 2. Before fitting the coupling into the drive train, remove 2 off bolts holding one of the fail safe straps. 3. Remove the fail safe strap to uncover the hole in the centre of the coupling. 4. Roll up the earthing connector (lengthways)

as tight as possible.

5. Push into the hole previously uncovered by removing the strapas far as possible.

6. Replace the fail safe strap ensuring that the connector is notdamaged, replace 2 off bolts.

7. Fit the coupling as per the installation instructions.8. Check electrical continuity on installation and thereafter

at three to six month intervals.

To Suit Coupling910-021910-001, 002, 007, 013, 014, 019, 020, 028, 043910-004, 005910-003, 006, 009, 012, 036, 037, 044, 052910-017, 018, 025, 026910-029, 038, 039, 040, 057910-032, 033910-015, 016, 022, 024, 046, 048, 053910-030, 041, 042, 047, 051910-035, 045, 049, 050910-062

R & D Marine Earthing Connector Application Guide

9/16

INSTALLATION PROCEDURE FOR R & D MARINE COUPLINGS1. Roughly align engine and stern gear without flexible coupling i.e. only two rigid half couplings pushed together.2. Bolt “R & D Marine” coupling between the two rigid couplings. Tightening details as below.3. Check alignment of engine by placing feeler gauges between the RED CONE

HEADED BOLT and the rigid half coupling. Repeat for the SAME bolt at 90° intervals by rotating the shaft.

4. If the gap is the same in all four positions, the engine is accurately aligned. Recommended minimum to maximum gap difference: 0.25 mm / 0.010 inch.

5. Run installation to bring engine compartment to working temperature. Re-check torque settings.

Recommended tightening torque:M8 - 27 Nm 20 lbsft 3/8 UNF - 40 Nm 30 lbsft M10 - 61 Nm 45 lbsft 7/16 UNF - 81 Nm 60 lbsft M12 - 108 Nm 80 lbsft1/2 UNF - 100 Nm 75 lbsft 5/8 UNF - 210 Nm 155 lbsft M18 - 338 Nm 250 lbsft 3/4 UNF - 366 Nm 270 lbsft

Part No103-036103-037103-038103-039103-040103-041103-042103-043103-044103-047103-053

Size (mm)9 x 5711 x 5715 x 5717 x 5719 x 5723 x 5725 x 5715 x 7517 x 759 x 3019 x 75

Designs are subject to constant review andimprovement therefore we reserve the rightto amend any dimension or detail specified orillustrated in this publication without noticeand without incurring any obligation to providesuch modification to products previouslydelivered.

Check Gap

GearboxFlange

ShaftFlange