fjr fjr13ax(c) owner's manual - yamaha motor … · fjr13ax(c) owner’s manual...

3P6-28199-12

FJR13AX(C)

OWNER’S MANUAL

LIT-11626-21-63

EAU10041

U3P612E0.book Page 1 Tuesday, October 16, 2007 9:14 AM

INTRODUCTIONEAU10080

Congratulations on your purchase of the Yamaha FJR13AX(C). This model is the result of Yamaha’s vast experience in theproduction of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship andreliability that have made Yamaha a leader in these fields.This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. If youhave any questions concerning the operation or maintenance of your motorcycle, please consult a Yamaha dealer.The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicable atthe date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of themotorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to therecommended maintenance schedules and operating instructions contained within this manual.


IMPORTANT MANUAL INFORMATIONEAU10131

Particularly important information is distinguished in this manual by the following notations:

NOTE:� This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle

is subsequently sold.� Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most

current product information available at the time of printing, there may be minor discrepancies between your motorcycleand this manual. If you have any questions concerning this manual, please consult your Yamaha dealer.

WARNINGEWA10010

PLEASE READ THIS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDING TIPS” BOOKLET CAREFULLYAND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE. DO NOT ATTEMPT TO OPERATE THIS MOTOR-CYCLE UNTIL YOU HAVE ATTAINED ADEQUATE KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES

The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Failure to follow WARNING instructions could result in severe injury or death to the motorcycle operator, a bystander or a person inspecting or repairing the motor-cycle.

A CAUTION indicates special precautions that must be taken to avoid damage to the motorcycle.

A NOTE provides key information to make procedures easier or clearer.

WARNING

CAUTION:

NOTE:


IMPORTANT MANUAL INFORMATIONAND UNTIL YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES. REGULAR INSPECTIONSAND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDING SKILLS, WILL ENSURE THAT YOU SAFELY ENJOYTHE CAPABILITIES AND THE RELIABILITY OF THIS MOTORCYCLE.

*Product and specifications are subject to change without notice.


IMPORTANT MANUAL INFORMATION

EAU10192

FJR13AX(C)OWNER’S MANUAL

©2007 by Yamaha Motor Corporation, U.S.A.1st edition, October 2007

All rights reserved.Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A.

is expressly prohibited.Printed in Japan.

P/N LIT-11626-21-63

AFFIX DEALER

LABEL HERE


TABLE OF CONTENTSSAFETY INFORMATION ..................1-1

Location of important labels ...........1-5

DESCRIPTION ..................................2-1Left view ..........................................2-1Right view........................................2-2Controls and instruments ................2-3

INSTRUMENT AND CONTROL FUNCTIONS .......................................3-1

Main switch/steering lock ................3-1Indicator and warning lights ............3-2Speedometer ..................................3-3Tachometer ....................................3-3Multi-function display ......................3-4Handlebar switches ........................3-8Clutch lever ..................................3-10Shift pedal ....................................3-11Brake lever ...................................3-11Brake pedal ..................................3-11ABS ..............................................3-12Fuel tank cap ................................3-13Fuel ..............................................3-13Catalytic converters ......................3-14Seats ............................................3-15Adjusting the rider seat height ......3-16Storage compartments .................3-18Accessory box ..............................3-19Adjusting the headlight beams .....3-19Handlebar position .......................3-20

Opening and closing the cowlings .................................... 3-20

Rear view mirrors ......................... 3-21Adjusting the front fork ................. 3-21Adjusting the shock absorber

assembly .................................. 3-23Sidestand ..................................... 3-24Ignition circuit cut-off system ....... 3-25Auxiliary DC jack .......................... 3-27

PRE-OPERATION CHECKS ............. 4-1Pre-operation check list ................. 4-2

OPERATION AND IMPORTANT RIDING POINTS ................................ 5-1

Starting the engine ......................... 5-1Shifting ........................................... 5-2Engine break-in .............................. 5-4Parking ........................................... 5-4

PERIODIC MAINTENANCE AND MINOR REPAIR................................. 6-1

PERIODIC MAINTENANCE .......... 6-1Owner’s tool kit .............................. 6-1Periodic maintenance chart for

the emission control system ....... 6-3General maintenance and

lubrication chart .......................... 6-4Removing and installing panels ..... 6-8Checking the spark plugs ............ 6-11Canister (for California only) ........ 6-12

Engine oil and oil filter cartridge ... 6-12Final gear oil ................................. 6-15Coolant .........................................6-17Cleaning the air filter element ...... 6-18Checking the engine idling

speed ........................................6-20Checking the throttle cable free

play ........................................... 6-20Valve clearance ............................ 6-20Tires ............................................. 6-21Cast wheels .................................. 6-23Accessories and replacement

parts .......................................... 6-24Clutch lever .................................. 6-24Rear brake light switch ................. 6-25Checking the front and rear

brake pads ................................ 6-25Checking the brake and clutch

fluid levels ................................. 6-26Changing the brake and clutch

fluids .........................................6-27Checking and lubricating the

cables ....................................... 6-27Checking and lubricating the

throttle grip and cable ............... 6-28Checking and lubricating the

brake and shift pedals ............... 6-28Checking and lubricating the

brake and clutch levers .............6-29Checking and lubricating the

centerstand and sidestand ........6-29


TABLE OF CONTENTSLubricating the swingarm pivots ...6-30Lubricating the rear suspension ...6-30Checking the front fork .................6-30Checking the steering ...................6-31Checking the wheel bearings .......6-32Battery ..........................................6-32Replacing the fuses ......................6-33Replacing a headlight bulb ...........6-35Front turn signal light ....................6-36Replacing a rear turn signal light

bulb or a tail/brake light bulb .....6-36Replacing the license plate light

bulb ...........................................6-37Troubleshooting ............................6-38Troubleshooting charts .................6-39

MOTORCYCLE CARE AND STORAGE ..........................................7-1

Matte color caution .........................7-1Care ................................................7-1Storage ...........................................7-3

SPECIFICATIONS .............................8-1

CONSUMER INFORMATION.............9-1Identification numbers ....................9-1Reporting safety defects .................9-3Motorcycle noise regulation ............9-4Maintenance record ........................9-5

YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY ............................... 9-7

YAMAHA EXTENDED SERVICE (Y.E.S.) ....................................... 9-9


1-1

1

SAFETY INFORMATIONEAU10281

MOTORCYCLES ARE SINGLETRACK VEHICLES. THEIR SAFE USEAND OPERATION ARE DEPENDENTUPON THE USE OF PROPER RIDINGTECHNIQUES AS WELL AS THE EX-PERTISE OF THE OPERATOR. EV-ERY OPERATOR SHOULD KNOWTHE FOLLOWING REQUIREMENTSBEFORE RIDING THIS MOTOR-CYCLE.HE OR SHE SHOULD:

� OBTAIN THOROUGH INSTRUC-TIONS FROM A COMPETENTSOURCE ON ALL ASPECTS OFMOTORCYCLE OPERATION.

� OBSERVE THE WARNINGS ANDMAINTENANCE REQUIRE-MENTS IN THE OWNER’S MAN-UAL.

� OBTAIN QUALIFIED TRAININGIN SAFE AND PROPER RIDINGTECHNIQUES.

� OBTAIN PROFESSIONAL TECH-NICAL SERVICE AS INDICATEDBY THE OWNER’S MANUAL

AND/OR WHEN MADE NECES-SARY BY MECHANICAL CONDI-TIONS.

Safe riding� Always make pre-operation

checks. Careful checks may helpprevent an accident.

� This motorcycle is designed to car-ry the operator and a passenger.

� The failure of motorists to detectand recognize motorcycles in traf-fic is the predominating cause ofautomobile/motorcycle accidents.Many accidents have been causedby an automobile driver who didnot see the motorcycle. Makingyourself conspicuous appears tobe very effective in reducing thechance of this type of accident.Therefore:• Wear a brightly colored jacket.• Use extra caution when you are

approaching and passingthrough intersections, since in-tersections are the most likelyplaces for motorcycle accidentsto occur.

• Ride where other motorists cansee you. Avoid riding in anothermotorist’s blind spot.

� Many accidents involve inexperi-enced operators. In fact, many op-erators who have been involved inaccidents do not even have a cur-rent motorcycle license.• Make sure that you are qualified

and that you only lend yourmotorcycle to other qualified op-erators.

• Know your skills and limits.Staying within your limits mayhelp you to avoid an accident.

• We recommend that you prac-tice riding your motorcyclewhere there is no traffic until youhave become thoroughly famil-iar with the motorcycle and all ofits controls.

� Many accidents have been causedby error of the motorcycle opera-tor. A typical error made by the op-erator is veering wide on a turn


SAFETY INFORMATION

1-2

1

due to EXCESSIVE SPEED or un-dercornering (insufficient lean an-gle for the speed).• Always obey the speed limit and

never travel faster than warrant-ed by road and traffic conditions.

• Always signal before turning orchanging lanes. Make sure thatother motorists can see you.

� The posture of the operator andpassenger is important for propercontrol.• The operator should keep both

hands on the handlebar andboth feet on the operator foot-rests during operation to main-tain control of the motorcycle.

• The passenger should alwayshold onto the operator, the seatstrap or grab bar, if equipped,with both hands and keep bothfeet on the passenger footrests.

• Never carry a passenger unlesshe or she can firmly place bothfeet on the passenger footrests.

� Never ride under the influence ofalcohol or other drugs.

� This motorcycle is designed for on-road use only. It is not suitable foroff-road use.

Protective apparelThe majority of fatalities from motor-cycle accidents are the result of headinjuries. The use of a safety helmet isthe single most critical factor in the pre-vention or reduction of head injuries.

� Always wear an approved helmet.� Wear a face shield or goggles.

Wind in your unprotected eyescould contribute to an impairmentof vision that could delay seeing ahazard.

� The use of a jacket, heavy boots,trousers, gloves, etc., is effective inpreventing or reducing abrasionsor lacerations.

� Never wear loose-fitting clothes,otherwise they could catch on thecontrol levers, footrests, or wheelsand cause injury or an accident.

� Never touch the engine or exhaustsystem during or after operation.They become very hot and can

cause burns. Always wear protec-tive clothing that covers your legs,ankles, and feet.

� A passenger should also observethe above precautions.

ModificationsModifications made to this motorcyclenot approved by Yamaha, or the re-moval of original equipment, may ren-der the motorcycle unsafe for use andmay cause severe personal injury.Modifications may also make yourmotorcycle illegal to use.

Loading and accessoriesAdding accessories or cargo to yourmotorcycle can adversely affect stabili-ty and handling if the weight distributionof the motorcycle is changed. To avoidthe possibility of an accident, use ex-treme caution when adding cargo oraccessories to your motorcycle. Useextra care when riding a motorcyclethat has added cargo or accessories.Here are some general guidelines tofollow if loading cargo or adding acces-sories to your motorcycle:


SAFETY INFORMATION

1-3

1

LoadingThe total weight of the operator, pas-senger, accessories and cargo mustnot exceed the maximum load limit.

When loading within this weight limit,keep the following in mind:

� Cargo and accessory weightshould be kept as low and close tothe motorcycle as possible. Makesure to distribute the weight asevenly as possible on both sides ofthe motorcycle to minimize imbal-ance or instability.

� Shifting weights can create a sud-den imbalance. Make sure that ac-cessories and cargo are securelyattached to the motorcycle beforeriding. Check accessory mountsand cargo restraints frequently.

� Never attach any large or heavyitems to the handlebar, front fork,or front fender. These items, in-cluding such cargo as sleeping

bags, duffel bags, or tents, cancreate unstable handling or a slowsteering response.

AccessoriesGenuine Yamaha accessories havebeen specifically designed for use onthis motorcycle. Since Yamaha cannottest all other accessories that may beavailable, you must personally be re-sponsible for the proper selection, in-stallation and use of non-Yamahaaccessories. Use extreme cautionwhen selecting and installing any ac-cessories.Keep the following guidelines in mind,as well as those provided under “Load-ing” when mounting accessories.

� Never install accessories or carrycargo that would impair the perfor-mance of your motorcycle. Care-fully inspect the accessory beforeusing it to make sure that it doesnot in any way reduce groundclearance or cornering clearance,

limit suspension travel, steeringtravel or control operation, or ob-scure lights or reflectors.• Accessories fitted to the handle-

bar or the front fork area cancreate instability due to improperweight distribution or aerody-namic changes. If accessoriesare added to the handlebar orfront fork area, they must be aslightweight as possible andshould be kept to a minimum.

• Bulky or large accessories mayseriously affect the stability ofthe motorcycle due to aerody-namic effects. Wind may at-tempt to lift the motorcycle, orthe motorcycle may become un-stable in cross winds. These ac-cessories may also causeinstability when passing or beingpassed by large vehicles.

• Certain accessories can dis-place the operator from his orher normal riding position. Thisimproper position limits the free-dom of movement of the opera-

Maximum load:211 kg (465 lb) (CAL)212 kg (467 lb) (U49)


SAFETY INFORMATION

1-4

1

tor and may limit control ability,therefore, such accessories arenot recommended.

� Use caution when adding electri-cal accessories. If electrical acces-sories exceed the capacity of themotorcycle’s electrical system, anelectric failure could result, whichcould cause a dangerous loss oflights or engine power.

Gasoline and exhaust gas� GASOLINE IS HIGHLY FLAMMA-

BLE:• Always turn the engine off when

refueling.• Take care not to spill any gaso-

line on the engine or exhaustsystem when refueling.

• Never refuel while smoking or inthe vicinity of an open flame.

� Never start the engine or let it runfor any length of time in a closedarea. The exhaust fumes are poi-sonous and may cause loss ofconsciousness and death within ashort time. Always operate yourmotorcycle in an area that has ad-equate ventilation.

� Always turn the engine off beforeleaving the motorcycle unattendedand remove the key from the mainswitch. When parking the motor-cycle, note the following:• The engine and exhaust system

may be hot, therefore, park themotorcycle in a place where pe-destrians or children are not like-ly to touch these hot areas.

• Do not park the motorcycle on aslope or soft ground, otherwise itmay fall over.

• Do not park the motorcycle neara flammable source, (e.g., a ker-osene heater, or near an openflame), otherwise it could catchfire.

� When transporting the motorcyclein another vehicle, make sure thatit is kept upright. If the motorcycleshould lean over, gasoline mayleak out of the fuel tank.

� If you should swallow any gaso-line, inhale a lot of gasoline vapor,or allow gasoline to get into youreyes, see your doctor immediately.If any gasoline spills on your skin

or clothing, immediately wash theaffected area with soap and waterand change your clothes.


SAFETY INFORMATION

1-5

1

EAU10381

Location of important labels Please read the following important labels carefully before operating this vehicle.


SAFETY INFORMATION

1-6

11 California only

2 California only

5

1 kg (2 lbs)4BR-24877-A0

LOAD LIMIT

4

3 kg (7 lbs)3TB-24877-A0

LOAD LIMIT

3 California only

PRESS. REGULATOR


SAFETY INFORMATION

1-7

16

8

7

9

10

CAUTIONCleaning with alkaline oracid cleaner, gasoline orsolvent will damagewindshield.Use neutral detergent.

5JW-00

270 kPa, {2.70 kgf/cm2}, 39psi

290 kPa, {2.90 kgf/cm2}, 42psi

270 kPa, {2.70 kgf/cm2}, 39psi

290 kPa, {2.90 kgf/cm2}, 42psi

3P6-21668-00


DESCRIPTION

2-1

2

EAU10410

Left view

1. Accessory box (page 3-19)2. Front fork spring preload adjusting bolt (page 3-21)3. Front fork rebound damping force adjusting knob (page 3-21)4. Owner’s tool kit (page 6-1)5. Rider seat (page 3-15)6. Passenger seat (page 3-15)7. Final gear oil filler bolt (page 6-15)8. Final gear oil drain bolt (page 6-15)

9. Shock absorber assembly spring preload adjusting lever (page 3-23)10.Air filter element (page 6-18)11.Shift pedal (page 3-11)12.Engine oil filler cap (page 6-12)13.Engine oil filter cartridge (page 6-12)14.Engine oil level check window (page 6-12)


DESCRIPTION

2-2

2

EAU10420

Right view

1. Storage compartment (page 3-18)2. Fuel tank cap (page 3-13)3. Fuse box (page 6-33)4. Windshield (page 3-8)5. Battery (page 6-32)6. Main fuse (page 6-33)7. Front fork compression damping force adjusting screw (page 3-21)8. Brake pedal (page 3-11)

9. Shock absorber assembly rebound damping force adjusting knob (page 3-23)

10.Rear brake fluid reservoir (page 6-26)


DESCRIPTION

2-3

2

EAU10430

Controls and instruments

1. Rear view mirror (page 3-21)2. Clutch lever (page 3-10)3. Left handlebar switches (page 3-8)4. Clutch fluid reservoir (page 6-26)5. Tachometer (page 3-3)6. Speedometer (page 3-3)7. Multi-function display (page 3-4)8. Front brake fluid reservoir (page 6-26)

9. Right handlebar switches (page 3-8)10.Brake lever (page 3-11)11.Throttle grip (page 6-20)12.Main switch/steering lock (page 3-1)13.Headlight beam adjusting knob (page 3-19)


INSTRUMENT AND CONTROL FUNCTIONS

3-1

3

EAU10460

Main switch/steering lock

The main switch/steering lock controlsthe ignition and lighting systems, and isused to lock the steering. The variouspositions are described below.

EAU35921

ONAll electrical circuits are supplied withpower, and the meter lighting, taillights,license plate light and position lightscome on, and the engine can be start-ed. The key cannot be removed.

NOTE:The headlights come on automaticallywhen the engine is started and stay onuntil the key is turned to “OFF”, even ifthe engine stalls.

EAU10660

OFFAll electrical systems are off. The keycan be removed.

EAU10690

LOCKThe steering is locked, and all electricalsystems are off. The key can be re-moved.

To lock the steering

1. Turn the handlebars all the way tothe left or right.

2. Push the key in from the “OFF” po-sition, and then turn it to “LOCK”while still pushing it.

3. Remove the key.

To unlock the steering

Push the key into the main switch, andthen turn it to “OFF” while still pushingit.

WARNINGEWA10060

Never turn the key to “OFF” or“LOCK” while the vehicle is moving,otherwise the electrical systems willbe switched off, which may result inloss of control or an accident. Makesure that the vehicle is stopped be-fore turning the key to “OFF” or“LOCK”.

1. Push.2. Turn.

1. Push.2. Turn.



3-2

3

EAU11003

Indicator and warning lights

EAU11030

Turn signal indicator lights “ ” and “ ” The corresponding indicator light flash-es when the turn signal switch ispushed to the left or right.

EAU11060

Neutral indicator light “ ” This indicator light comes on when thetransmission is in the neutral position.

EAU11080

High beam indicator light “ ” This indicator light comes on when thehigh beam of the headlight is switchedon.

EAU11120

Oil level warning light “ ” This warning light comes on when theengine oil level is low.The electrical circuit of the warning lightcan be checked by turning the key to“ON”.If the warning light does not come onfor a few seconds, then go off, have aYamaha dealer check the electrical cir-cuit.

NOTE:Even if the oil level is sufficient, thewarning light may flicker when riding ona slope or during sudden accelerationor deceleration, but this is not a mal-function.

EAU11530

Engine trouble warning light “ ” This warning light comes on or flasheswhen an electrical circuit monitoring theengine is defective. When this occurs,have a Yamaha dealer check the self-diagnosis system. (See page 3-8 for anexplanation of the self-diagnosis de-vice.)The electrical circuit of the warning lightcan be checked by turning the key to“ON”. If the warning light does not comeon for a few seconds, then go off, havea Yamaha dealer check the electricalcircuit.

EAU39500

ABS warning light “ ” If this warning light comes on or flasheswhile riding, the ABS may be defective.If this occurs, have a Yamaha dealercheck the system as soon as possible.(See page 3-12.)

WARNINGEWA10081

If the ABS warning light comes on orflashes while riding, the brake sys-tem reverts to conventional braking.Therefore, be careful not to causethe wheels to lock during emergen-

1. Left turn signal indicator light “ ”2. Right turn signal indicator light “ ”3. Engine trouble warning light “ ”4. Anti-lock Brake System (ABS) warning

light “ ”5. Neutral indicator light “ ”6. High beam indicator light “ ”7. Oil level warning light “ ”

ABS

ABS



3-3

3

cy braking. If the warning lightcomes on or flashes while riding,have a Yamaha dealer check thebrake system as soon as possible.

The electrical circuit of the warning lightcan be checked by turning the key to“ON”.If the warning light does not come on orremains on, have a Yamaha dealercheck the electrical circuit.

EAU11601

Speedometer

The speedometer shows the ridingspeed.When the key is turned to “ON”, thespeedometer needle will sweep onceacross the speed range and then returnto zero in order to test the electrical cir-cuit.

EAU11872

Tachometer

The electric tachometer allows the riderto monitor the engine speed and keep itwithin the ideal power range.When the key is turned to “ON”, the ta-chometer needle will sweep onceacross the r/min range and then returnto zero r/min in order to test the electri-cal circuit.

CAUTION:ECA10031

Do not operate the engine in the ta-chometer red zone.Red zone: 9000 r/min and above

1. Tachometer2. Speedometer3. Multi-function display

1. Tachometer2. Tachometer red zone



3-4

3

EAU40292

Multi-function display

WARNINGEWA14430

Be sure to stop the vehicle beforemaking any setting changes to themulti-function display.

The multi-function display is equippedwith the following:

� an odometer (which shows the to-tal distance traveled)

� two tripmeters (which show thedistance traveled since they werelast set to zero)

� a fuel reserve tripmeter (whichshows the distance traveled on thefuel reserve)

� a clock� a fuel meter� a coolant temperature meter� a transmission gear display� an ambient temperature display� a fuel consumption display (instan-

taneous and average consumptionfunctions)

� a self-diagnosis device

NOTE:Be sure to turn the key to “ON” beforeusing the “SELECT” and “RESET” but-tons.

Odometer and tripmeter modes

Pushing the “SELECT” button switchesthe display between the odometermode “ODO” and the tripmeter modes“TRIP 1” and “TRIP 2” in the followingorder:ODO → TRIP 1 → TRIP 2 → ODO

NOTE:When selecting “TRIP 1” or “TRIP 2”,the display flashes for five seconds.

When approximately 5.5 L (1.45 USgal) (1.21 Imp.gal) of fuel remains in thefuel tank, the display will automaticallychange to the fuel reserve tripmetermode “F-TRIP” and start counting the

1. Multi-function display2. “SELECT” button3. “RESET” button

1. Odometer/tripmeter/fuel reserve tripmeter2. “SELECT” button3. “RESET” button



3-5

3

distance traveled from that point. In thatcase, pushing the “SELECT” buttonswitches the display between the vari-ous tripmeter and odometer modes inthe following order:F-TRIP → ODO → TRIP 1 → TRIP 2 →F-TRIPTo reset a tripmeter, select it by push-ing the “SELECT” button, and thenpush the “SELECT” button for at leastone second while the display is flash-ing. If you do not reset the fuel reservetripmeter manually, it will reset itself au-tomatically and the display will return tothe prior mode after refueling and trav-eling 5 km (3 mi).

Clock

To set the clock:1. Push the “SELECT” button and

“RESET” button together for atleast two seconds.

2. When the hour digits start flashing,push the “RESET” button to set thehours.

3. Push the “SELECT” button, andthe minute digits will start flashing.

4. Push the “RESET” button to setthe minutes.

5. Push the “SELECT” button andthen release it to start the clock.

Fuel meter

The fuel meter indicates the amount offuel in the fuel tank. The display seg-ments of the fuel meter disappear to-wards “E” (Empty) as the fuel leveldecreases. When the last segmentstarts flashing, refuel as soon as possi-ble. When the key is turned to “ON”, allof the display segments of the fuelmeter will appear one after the otherand then disappear in order to test theelectrical circuit.

NOTE:This fuel meter is equipped with a self-diagnosis system. If the electrical circuitis defective, all the display segments

1. Clock2. “SELECT” button3. “RESET” button

1. Fuel meter



3-6

3

will start flashing. If this occurs, have aYamaha dealer check the electrical cir-cuit.

Coolant temperature meter

With the key in the “ON” position, thecoolant temperature meter indicatesthe temperature of the coolant. Whenthe key is turned to “ON”, all of the dis-play segments of the coolant tempera-ture meter will appear one after theother and then disappear in order totest the electrical circuit. The coolanttemperature varies with changes in theweather and engine load. If the top seg-ment flashes, stop the vehicle and letthe engine cool. (See page 6-39.)

CAUTION:ECA10020

Do not operate the engine if it isoverheated.

Transmission gear display

This display shows the selected gear.The neutral position, however, is notdisplayed, it is indicated by the neutralindicator light.

Ambient temperature, instanta-neous fuel consumption and aver-age fuel consumption modes

Push the “RESET” button to switch thedisplay between the ambient tempera-ture mode “Air”, the instantaneous fuelconsumption mode “MPG” and the av-erage fuel consumption mode “AV_ _._MPG” in the following order:Air → MPG → AV_ _._ MPG → Air

1. Coolant temperature meter1. Transmission gear display2. Neutral indicator light “ ”

1. Ambient temperature/instantaneous fuel consumption/average fuel consumption

2. “SELECT” button3. “RESET” button



3-7

3

Ambient temperature mode

This display shows the ambient tem-perature from 16 °F to 122 °F in 1 °F in-crements. The temperature displayedmay vary from the ambient tempera-ture.

NOTE:� If the ambient temperature falls be-

low 16 °F, a lower temperaturethan 16 °F will not be displayed.

� If the ambient temperature climbsabove 122 °F, a higher tempera-ture than 122 °F will not be dis-played.

� The accuracy of the temperaturereading may be affected whenriding slowly [approximately under

20 km/h (12.5 mi/h)] or whenstopped at traffic signals, railroadcrossings, etc.

Instantaneous fuel consumption mode

This display shows the distance thatcan be traveled on 1.0 US.gal of fuelunder the current riding conditions.

NOTE:If traveling at speeds under 10 km/h(6.0 mi/h), “_ _._” will be displayed.

Average fuel consumption mode

This display shows the average fuelconsumption since it was last reset.When the average fuel consumptionmode is selected, the display flashesfor five seconds, and then “AV_ _._MPG” (average distance that can betraveled using 1.0 US.gal of fuel) is dis-played.

NOTE:� To reset the average fuel con-

sumption display, push the “RE-SET” button to select the modeagain, and then push the “RESET”button for 1 second while the dis-play is flashing.

1. Ambient temperature

1. Instantaneous fuel consumption

1. Average fuel consumption



3-8

3

� After resetting the average fuelconsumption display, “_ _._” willbe shown for that display until thevehicle has traveled 1 km (0.6 mi).

CAUTION:ECA15472

If there is a malfunction, “– –.–” willbe displayed. Have a Yamaha dealercheck the vehicle.

Self-diagnosis device

This model is equipped with a self-diag-nosis device for various electrical cir-cuits.

If any of those circuits are defective, theengine trouble warning light will comeon, and then the multi-function displaywill indicate a two-digit error code.If the multi-function display indicatessuch an error code, note the code num-ber, and then have a Yamaha dealercheck the vehicle.

CAUTION:ECA11790

If the multi-function display indi-cates an error code, the vehicleshould be checked as soon as pos-sible in order to avoid engine dam-age.

EAU12347

Handlebar switches

Left

1. Error code display

1. Windshield position adjusting switch “ ”2. Dimmer switch “ / ”3. Turn signal switch “ / ”4. Horn switch “ ”



3-9

3

Right

EAU12400

Dimmer switch “ / ” Set this switch to “ ” for the highbeam and to “ ” for the low beam.

EAU12460

Turn signal switch “ / ” To signal a right-hand turn, push thisswitch to “ ”. To signal a left-handturn, push this switch to “ ”. When re-leased, the switch returns to the centerposition. To cancel the turn signallights, push the switch in after it has re-turned to the center position.

EAU12493

Windshield position adjusting switch “ ” To move the windshield up, push thisswitch in direction (a). To move thewindshield down, push the switch in di-rection (b).

NOTE:When the key is turned to “OFF”, thewindshield will automatically return tothe lowest position.

EAU12500

Horn switch “ ” Press this switch to sound the horn.

EAU12660

Engine stop switch “ / ” Set this switch to “ ” before startingthe engine. Set this switch to “ ” tostop the engine in case of an emergen-cy, such as when the vehicle overturnsor when the throttle cable is stuck.

EAU12710

Start switch “ ” Push this switch to crank the enginewith the starter.

CAUTION:ECA10050

See page 5-1 for starting instruc-tions prior to starting the engine.

EAU42340

The engine trouble warning light andABS warning light will come on whenthe key is turned to “ON” and the startswitch is pushed, but this does not indi-cate a malfunction.

EAU12765

Hazard switch “ ” With the key in the “ON” position, usethis switch to turn on the hazard lights(simultaneous flashing of all turn signallights).

1. Engine stop switch “ / ”2. Hazard switch “ ”3. Start switch “ ”

1. Windshield position adjusting switch “ ”



3-10

3

The hazard lights are used in case ofan emergency or to warn other driverswhen your vehicle is stopped where itmight be a traffic hazard.

CAUTION:ECA10061

Do not use the hazard lights for anextended length of time with the en-gine not running, otherwise the bat-tery may discharge.

EAU12830

Clutch lever

The clutch lever is located at the lefthandlebar grip. To disengage theclutch, pull the lever toward the handle-bar grip. To engage the clutch, releasethe lever. The lever should be pulledrapidly and released slowly for smoothclutch operation.The clutch lever is equipped with aclutch lever position adjusting dial. Toadjust the distance between the clutchlever and the handlebar grip, turn theadjusting dial while holding the leverpushed away from the handlebar grip.

Make sure that the appropriate settingon the adjusting dial is aligned with thearrow mark on the clutch lever.The clutch lever is equipped with aclutch switch, which is part of the igni-tion circuit cut-off system. (See page3-25.)

1. Clutch lever2. Arrow mark3. Clutch lever position adjusting dial4. Distance between clutch lever and handlebar

grip



3-11

3

EAU12870

Shift pedal

The shift pedal is located on the leftside of the engine and is used in com-bination with the clutch lever whenshifting the gears of the 5-speed con-stant-mesh transmission equipped onthis motorcycle.

EAU26823

Brake lever The brake lever is located at the righthandlebar grip. To apply the frontbrake, pull the lever toward the handle-bar grip.

The brake lever is equipped with abrake lever position adjusting dial. Toadjust the distance between the brakelever and the handlebar grip, turn theadjusting dial while holding the leverpushed away from the handlebar grip.Make sure that the appropriate settingon the adjusting dial is aligned withthe “ ” mark on the brake lever.

EAU39540

Brake pedal

The brake pedal is on the right side ofthe vehicle.This model is equipped with a unifiedbrake system.When pressing down on the brake ped-al, the rear brake and a portion of thefront brake are applied. For full brakingperformance, apply both the brake le-ver and the brake pedal simultaneous-ly.

1. Shift pedal

1. Brake lever2. “ ” mark3. Brake lever position adjusting dial4. Distance between brake lever and handlebar

grip

1. Brake pedal



3-12

3

EAU39531

ABS The Yamaha ABS (Anti-lock BrakeSystem) features a dual electronic con-trol system, which acts on the front andrear brakes independently. The ABS ismonitored by an ECU (Electronic Con-trol Unit), which will have recourse tomanual braking if a malfunction occurs.

WARNINGEWA10090

� The ABS performs best on longbraking distances.

� On certain (rough or gravel)roads, the braking distance maybe longer with than without theABS. Therefore, always keep asufficient distance to the vehicleahead to match the ridingspeed.

NOTE:� The ABS performs a self-diagno-

sis test for a few seconds eachtime the vehicle first starts off afterthe main switch was turned on.During this test, a “clicking” noisecan be heard from under the seat,and if the brake lever or brake ped-

al are even slightly applied, a vi-bration can be felt at the lever andpedal, but these do not indicate amalfunction.

� When the ABS is activated, thebrakes are operated in the usualway. A pulsating action may be feltat the brake lever or brake pedal,but this does not indicate a mal-function.

� This ABS has a test mode whichallows the owner to experience thepulsating at the brake lever orbrake pedal when the ABS is oper-ating. However, special tools arerequired, so please consult yourYamaha dealer when performingthis test.

CAUTION:ECA16120

Keep any type of magnets (includingmagnetic pick-up tools, magneticscrewdrivers, etc.) away from thefront and rear wheel hubs, otherwisethe magnetic rotors equipped in thewheel hubs may be damaged, result-ing in improper performance of theABS system.

1. Front wheel hub

1. Rear wheel hub

1

1



3-13

3

EAU13072

Fuel tank cap

To open the fuel tank capOpen the fuel tank cap lock cover, in-sert the key into the lock, and then turnit 1/4 turn clockwise. The lock will be re-leased and the fuel tank cap can beopened.

To close the fuel tank cap1. Push the fuel tank cap into position

with the key inserted in the lock.2. Turn the key counterclockwise to

the original position, remove it, andthen close the lock cover.

NOTE:The fuel tank cap cannot be closed un-less the key is in the lock. In addition,the key cannot be removed if the cap isnot properly closed and locked.

WARNINGEWA11090

Make sure that the fuel tank cap isproperly closed before riding.

EAU13220

Fuel

Make sure that there is sufficient fuel inthe tank. When refueling, be sure to in-sert the pump nozzle into the fuel tankfiller hole and to fill the tank to the bot-tom of the filler tube as shown.

WARNINGEWA10880

� Do not overfill the fuel tank, oth-erwise it may overflow when thefuel warms up and expands.

� Avoid spilling fuel on the hot en-gine.

1. Fuel tank cap lock cover2. Unlock.

1. Fuel tank filler tube2. Fuel level



3-14

3

CAUTION:ECA10070

Immediately wipe off spilled fuelwith a clean, dry, soft cloth, sincefuel may deteriorate painted surfac-es or plastic parts.

EAU13300

CAUTION:ECA11400

Use only unleaded gasoline. The useof leaded gasoline will cause severedamage to internal engine parts,such as the valves and piston rings,as well as to the exhaust system.

Your Yamaha engine has been de-signed to use regular unleaded gaso-line with a pump octane number[(R+M)/2] of 86 or higher, or a researchoctane number of 91 or higher. If

knocking (or pinging) occurs, use agasoline of a different brand or premi-um unleaded fuel. Use of unleaded fuelwill extend spark plug life and reducemaintenance costs.GasoholThere are two types of gasohol: gaso-hol containing ethanol and that contain-ing methanol. Gasohol containingethanol can be used if the ethanol con-tent does not exceed 10%. Gasoholcontaining methanol is not recom-mended by Yamaha because it cancause damage to the fuel system or ve-hicle performance problems.

EAU13442

Catalytic converters This vehicle is equipped with catalyticconverters in the exhaust system.

WARNINGEWA10860

The exhaust system is hot after op-eration. Make sure that the exhaustsystem has cooled down before do-ing any maintenance work.

CAUTION:ECA10700

The following precautions must beobserved to prevent a fire hazard orother damages.

� Use only unleaded gasoline.The use of leaded gasoline willcause unrepairable damage tothe catalytic converter.

� Never park the vehicle near pos-sible fire hazards such as grassor other materials that easilyburn.

� Do not allow the engine to idletoo long.

Recommended fuel:UNLEADED GASOLINE ONLY

Fuel tank capacity:25.0 L (6.61 US gal) (5.50 Imp.gal)

Fuel reserve amount:5.5 L (1.45 US gal) (1.21 Imp.gal)



3-15

3

EAU39492

Seats

Passenger seat

To remove the passenger seat1. Insert the key into the passenger

seat lock, and then turn it counter-clockwise.

2. Lift the front of the passenger seatand pull it forward.

To install the passenger seat1. Insert the projections on the rear of

the passenger seat into the seatholders as shown, and then pushthe front of the seat down to lock itin place.

2. Remove the key.

Rider seat

To remove the rider seat1. Remove the passenger seat.2. Push the rider seat lock lever, lo-

cated under the back of the riderseat, to the left as shown, and thenpull the seat off.

To install the rider seat1. Insert the projection on the front of

the rider seat into the seat holderas shown, and then push the rearof the seat down to lock it in place.

1. Passenger seat lock2. Unlock.

1. Projection2. Seat holder

1. Rider seat lock lever2. Rider seat

1. Projection2. Seat holder



3-16

3

2. Install the passenger seat.

NOTE:� Make sure that the seats are prop-

erly secured before riding.� The rider seat height can be ad-

justed to change the riding posi-tion. (See page 3-16.)

EAU39632

Adjusting the rider seat height The rider seat height can be adjusted toone of two positions to suit the rider’spreference.The rider seat height was adjusted tothe lower position at delivery.

To change the rider seat height tothe high position

1. Remove the rider seat. (See page3-15.)

2. Remove the rider seat height posi-tion adjuster by pulling it upward.

3. Move the rider seat holder cover tothe lower position as shown.

4. Install the rider seat height positionadjuster so that the “H” mark isaligned with the match mark.

1. Low position2. High position

1. Rider seat height position adjuster

1. Rider seat holder cover



3-17

3

5. Insert the projection on the front ofthe rider seat into seat holder B asshown.

6. Align the projection on the bottomof the rider seat with the “H” posi-tion slot, and then push the rear ofthe seat down to lock it in place asshown.


To change the rider seat height tothe low position

1. Remove the rider seat. (See page3-15.)

2. Remove the rider seat height posi-tion adjuster by pulling it upward.

3. Move the rider seat holder cover tothe upper position.

4. Install the rider seat height positionadjuster so that the “L” mark isaligned with the match mark.

5. Insert the projection on the front ofthe rider seat into seat holder A asshown.

1. Rider seat height position adjuster2. “H” mark3. Match mark

1. Projection2. Seat holder B (for high position)3. Rider seat holder cover

1. “H” position slot

1. Rider seat height position adjuster2. “L” mark3. Match mark

1. Projection2. Seat holder A (for low position)3. Rider seat holder cover



3-18

3

6. Align the projection on the bottomof the rider seat with the “L” posi-tion slot, and then push the rear ofthe seat down to lock it in place asshown.


NOTE:Make sure that the seats are properlysecured before riding.

EAU40250

Storage compartments This vehicle is equipped with two stor-age compartments.Storage compartment A is located un-der the rider seat. (See page 3-15.)

Storage compartment B is located un-der the passenger seat. (See page3-15.)

WARNINGEWA14420

� Do not exceed the load limit of 1kg (2 lb) for storage compart-ment A.

� Do not exceed the load limit of 3kg (7 lb) for storage compart-ment B.

� Do not exceed the maximumload of 211 kg (465 lb) (CAL)212 kg (467 lb) (U49) for the ve-hicle.

1. “L” position slot1. Storage compartment A

1. Storage compartment B



3-19

3

EAU39480

Accessory box The accessory box is located besidethe meter panel.

To open the accessory box1. Insert the key into the main switch,

and then turn it to “ON”.2. Push the accessory box button,

and then open the accessory boxlid.

3. Turn the key to “OFF” to preservethe battery.

To close the accessory box1. Fold the accessory box lid down.

2. Remove the key.

CAUTION:ECA11800

Do not place heat-sensitive items inthe accessory box. The accessorybox gets extremely hot especiallywhen the engine is running or is hot.

WARNINGEWA11421

� Do not exceed the load limit of0.3 kg (0.66 lb) for the accessorybox.

� Do not exceed the maximumload of 211 kg (465 lb) (CAL)212 kg (467 lb) (U49) for the ve-hicle.

EAU39611

Adjusting the headlight beams The headlight beam adjusting knobsare used to raise or lower the height ofthe headlight beams. It may be neces-sary to adjust the headlight beams toincrease visibility and help preventblinding oncoming drivers when carry-ing more or less load than usual. Obeylocal laws and regulations when adjust-ing the headlights.To raise the headlight beams, turn theknobs in direction (a). To lower theheadlight beams, turn the knobs in di-rection (b).

1. Accessory box lid2. Accessory box3. Accessory box button

1. Headlight beam adjusting knob



3-20

3

EAU39641

Handlebar position The handlebars can be adjusted to oneof three positions to suit the rider’s pref-erence. Have a Yamaha dealer adjustthe position of the handlebars.

EAU39621

Opening and closing the cowl-ings The cowlings can be tilted back 30 mm(1.18 in) for added ventilation to suit theriding conditions.

To open a cowling1. Remove the quick fastener

screws.

2. Pull the cowling to the open posi-tion, and then install the quick fas-tener screws.

To close a cowling1. Remove the quick fastener

screws.

1. Handlebar 1. Closed position2. Open position3. Cowling

1. Quick fastener screw

1. Open position



3-21

3

2. Push the cowling to the closed po-sition, and then install the quickfastener screws.

NOTE:Make sure that the cowling is properlyinstalled before riding.

EAU39671

Rear view mirrors The rear view mirrors of this vehicle canbe folded forward or backward for park-ing in narrow spaces. Fold the mirrorsback to their original position beforeriding.

WARNINGEWA14371

Be sure to fold the rear view mirrorsback to their original position beforeriding.

EAU14731

Adjusting the front fork This front fork is equipped with springpreload adjusting bolts, rebound damp-ing force adjusting knobs and compres-sion damping force adjusting screws.

WARNINGEWA10180

Always adjust both fork legs equal-ly, otherwise poor handling and lossof stability may result.

Spring preload

To increase the spring preload andthereby harden the suspension, turnthe adjusting bolt on each fork leg in di-rection (a). To decrease the spring pre-

1. Quick fastener screw

1. Closed position

1. Riding position2. Parking position

1. Spring preload adjusting bolt



3-22

3

load and thereby soften thesuspension, turn the adjusting bolt oneach fork leg in direction (b).

NOTE:Align the appropriate groove on the ad-justing mechanism with the top of thefront fork cap bolt.

Rebound damping force

To increase the rebound damping forceand thereby harden the rebound damp-ing, turn the adjusting knob on eachfork leg in direction (a). To decrease therebound damping force and therebysoften the rebound damping, turn theadjusting knob on each fork leg in direc-tion (b).

Compression damping force

To increase the compression dampingforce and thereby harden the compres-sion damping, turn the adjusting screwon each fork leg in direction (a). To de-crease the compression damping forceand thereby soften the compressiondamping, turn the adjusting screw oneach fork leg in direction (b).

1. Current setting2. Front fork cap bolt

Spring preload setting:Minimum (soft):

6Standard:

4Maximum (hard):

1

1. Rebound damping force adjusting knob

Rebound damping setting:Minimum (soft):

17 click(s) in direction (b)*Standard:

12 click(s) in direction (b)*Maximum (hard):

1 click(s) in direction (b)** With the adjusting knob fully turned

in direction (a)

1. Compression damping force adjusting screw

Compression damping setting:Minimum (soft):



1 click(s) in direction (b)** With the adjusting screw fully turned

in direction (a)



3-23

3

CAUTION:ECA10100

Never attempt to turn an adjustingmechanism beyond the maximum orminimum settings.

NOTE:Although the total number of clicks of adamping force adjusting mechanismmay not exactly match the above spec-ifications due to small differences inproduction, the actual number of clicksalways represents the entire adjustingrange. To obtain a precise adjustment,it would be advisable to check the num-ber of clicks of each damping force ad-justing mechanism and to modify thespecifications as necessary.

EAU14911

Adjusting the shock absorber assembly This shock absorber assembly isequipped with a spring preload adjust-ing lever and a rebound damping forceadjusting knob.

CAUTION:ECA10100

Never attempt to turn an adjustingmechanism beyond the maximum orminimum settings.

Spring preload

For riding solo, move the spring preloadadjusting lever in direction (b). Forriding with a passenger, move thespring preload adjusting lever in direc-tion (a).

Rebound damping force

To increase the rebound damping forceand thereby harden the rebound damp-ing, turn the adjusting knob in direction(a). To decrease the rebound dampingforce and thereby soften the rebounddamping, turn the adjusting knob in di-rection (b).1. Spring preload adjusting lever

1. Rebound damping force adjusting knob



3-24

3

WARNINGEWA10220

This shock absorber contains highlypressurized nitrogen gas. For prop-er handling, read and understandthe following information beforehandling the shock absorber. Themanufacturer cannot be held re-sponsible for property damage orpersonal injury that may result fromimproper handling.

� Do not tamper with or attempt toopen the gas cylinder.

� Do not subject the shock ab-sorber to an open flame or otherhigh heat sources, otherwise itmay explode due to excessivegas pressure.

� Do not deform or damage thegas cylinder in any way, as thiswill result in poor damping per-formance.

� Always have a Yamaha dealerservice the shock absorber.

EAU15301

Sidestand The sidestand is located on the left sideof the frame. Raise the sidestand orlower it with your foot while holding thevehicle upright.

NOTE:The built-in sidestand switch is part ofthe ignition circuit cut-off system, whichcuts the ignition in certain situations.(See further down for an explanation ofthe ignition circuit cut-off system.)

WARNINGEWA10240

The vehicle must not be ridden withthe sidestand down, or if the side-stand cannot be properly moved up(or does not stay up), otherwise thesidestand could contact the groundand distract the operator, resultingin a possible loss of control.Yamaha’s ignition circuit cut-offsystem has been designed to assistthe operator in fulfilling the respon-sibility of raising the sidestand be-fore starting off. Therefore, checkthis system regularly as described

Rebound damping setting:Minimum (soft):



3 click(s) in direction (b)** With the adjusting knob fully turned

in direction (a)



3-25

3

below and have a Yamaha dealer re-pair it if it does not function proper-ly.

EAU44900

Ignition circuit cut-off system The ignition circuit cut-off system (com-prising the sidestand switch, clutchswitch and neutral switch) has the fol-lowing functions.

� It prevents starting when the trans-mission is in gear and the side-stand is up, but the clutch lever isnot pulled.

� It prevents starting when the trans-mission is in gear and the clutch le-ver is pulled, but the sidestand isstill down.

� It cuts the running engine when thetransmission is in gear and the sid-estand is moved down.

Periodically check the operation of theignition circuit cut-off system accordingto the following procedure.

WARNINGEWA10260

� The vehicle must be placed onthe centerstand during this in-spection.

� If a malfunction is noted, have aYamaha dealer check the sys-tem before riding.



3-26

3

With the engine turned off:1. Move the sidestand down.2. Make sure that the engine stop switch is turned on.3. Turn the key on. 4. Shift the transmission into the neutral position.5. Push the start switch.Does the engine start?

With the engine still running:6. Move the sidestand up.7. Keep the clutch lever pulled.8. Shift the transmission into gear.9. Move the sidestand down.Does the engine stall?

After the engine has stalled:10. Move the sidestand up.11. Keep the clutch lever pulled.12. Push the start switch.Does the engine start?

The system is OK. The motorcycle can be ridden.

The neutral switch may be defective.The motorcycle should not be ridden untilchecked by a Yamaha dealer.

The sidestand switch may be defective.The motorcycle should not be ridden untilchecked by a Yamaha dealer.

The clutch switch may be defective.The motorcycle should not be ridden untilchecked by a Yamaha dealer.

YES NO

YES NO

YES NO



3-27

3

EAU39651

Auxiliary DC jack This vehicle is equipped with an auxilia-ry DC jack in the accessory box.A 12-V accessory connected to theauxiliary jack can be used when the keyis in the “ON” position and should onlybe used when the engine is running.

CAUTION:ECA15430

The accessory connected to theauxiliary DC jack should not be usedwith the engine turned off, and theload must never exceed 30 W (2.5 A),otherwise the battery may dis-charge.

To use the auxiliary DC jack1. Open the accessory box lid. (See

page 3-19.)2. Turn the key to “OFF”.3. Remove the auxiliary DC jack cap.

4. Insert the accessory plug into theauxiliary DC jack.

5. Turn the key to “ON”, and thenstart the engine. (See page 5-1.)

WARNINGEWA14360

To prevent electrical shock or short-circuiting, make sure that the cap isinstalled when the auxiliary DC jackis not being used.

1. Auxiliary DC jack cap

1. Auxiliary DC jack


PRE-OPERATION CHECKS

4-1

4

EAU15593

The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly,even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or lossof tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough visual inspec-tion, to check the following points before each ride.

NOTE:Pre-operation checks should be made each time the vehicle is used. Such an inspection can be accomplished in a very shorttime; and the added safety it assures is more than worth the time involved.

WARNINGEWA11150

If any item in the Pre-operation check list is not working properly, have it inspected and repaired before operatingthe vehicle.



4-2

4

EAU15605

Pre-operation check list ITEM CHECKS PAGE

Fuel• Check fuel level in fuel tank.• Refuel if necessary.• Check fuel line for leakage.

3-13

Engine oil• Check oil level in engine.• If necessary, add recommended oil to specified level.• Check vehicle for oil leakage.

6-12

Final gear oil • Check vehicle for oil leakage. 6-15

Coolant• Check coolant level in reservoir.• If necessary, add recommended coolant to specified level.• Check cooling system for leakage.

6-17

Front brake

• Check operation.• If soft or spongy, have Yamaha dealer bleed hydraulic system.• Check brake pads for wear.• Replace if necessary.• Check fluid level in reservoir.• If necessary, add recommended brake fluid to specified level.• Check hydraulic system for leakage.

6-25, 6-26

Rear brake

• Check operation.• If soft or spongy, have Yamaha dealer bleed hydraulic system.• Check brake pads for wear.• Replace if necessary.• Check fluid level in reservoir.• If necessary, add recommended brake fluid to specified level.• Check hydraulic system for leakage.

6-25, 6-26

Clutch

• Check operation.• If soft or spongy, have Yamaha dealer bleed hydraulic system.• Check fluid level in reservoir.• If necessary, add recommended fluid to specified level.• Check hydraulic system for leakage.

6-24, 6-26



4-3

4

Throttle grip

• Make sure that operation is smooth.• Check cable free play.• If necessary, have Yamaha dealer adjust cable free play and lubricate cable and

grip housing.

6-20, 6-28

Control cables • Make sure that operation is smooth.• Lubricate if necessary. 6-27

Wheels and tires

• Check for damage.• Check tire condition and tread depth.• Check air pressure.• Correct if necessary.

6-21, 6-23

Brake and shift pedals • Make sure that operation is smooth.• Lubricate pedal pivoting points if necessary. 6-28

Brake and clutch levers • Make sure that operation is smooth.• Lubricate lever pivoting points if necessary. 6-29

Centerstand, sidestand • Make sure that operation is smooth.• Lubricate pivots if necessary. 6-29

Chassis fasteners • Make sure that all nuts, bolts and screws are properly tightened.• Tighten if necessary. —

Instruments, lights, signals and switches

• Check operation.• Correct if necessary. —

Sidestand switch • Check operation of ignition circuit cut-off system.• If system is defective, have Yamaha dealer check vehicle. 3-24

ITEM CHECKS PAGE


OPERATION AND IMPORTANT RIDING POINTS

5-1

5

EAU15950

WARNINGEWA10270

� Become thoroughly familiarwith all operating controls andtheir functions before riding.Consult a Yamaha dealer re-garding any control or functionthat you do not thoroughly un-derstand.

� Never start the engine or oper-ate it in a closed area for anylength of time. Exhaust fumesare poisonous, and inhalingthem can cause loss of con-sciousness and death within ashort time. Always make surethat there is adequate ventila-tion.

� Before starting out, make surethat the sidestand is up. If thesidestand is not raised com-pletely, it could contact theground and distract the opera-tor, resulting in a possible lossof control.

EAU45310

NOTE:This model is equipped with a lean an-gle sensor to stop the engine in case ofa turnover. To start the engine after aturnover, be sure to turn the mainswitch to “OFF” and then to “ON”. Fail-ing to do so will prevent the engine fromstarting even though the engine willcrank when pushing the start switch.

EAU40281

Starting the engine In order for the ignition circuit cut-offsystem to enable starting, one of thefollowing conditions must be met:

� The transmission is in the neutralposition.

� The transmission is in gear withthe clutch lever pulled and the sid-estand up.

WARNINGEWA10290

� Before starting the engine,check the function of the igni-tion circuit cut-off system ac-cording to the proceduredescribed on page 3-25.

� Never ride with the sidestanddown.

1. Turn the key to “ON” and makesure that the engine stop switch isset to “ ”.

CAUTION:ECA15500

The following warning lights shouldcome on for a few seconds, then gooff.

� Oil level warning light� Engine trouble warning light



5-2

5

� ABS warning lightIf a warning light does not go off, seepage 3-2 for the correspondingwarning light circuit check.

2. Shift the transmission into the neu-tral position.

NOTE:When the transmission is in the neutralposition, the neutral indicator lightshould be on, otherwise have aYamaha dealer check the electrical cir-cuit.

3. Start the engine by pushing thestart switch.

NOTE:If the engine fails to start, release thestart switch, wait a few seconds, andthen try again. Each starting attemptshould be as short as possible to pre-serve the battery. Do not crank the en-gine more than 10 seconds on any oneattempt.

CAUTION:ECA11130

For maximum engine life, alwayswarm the engine up before startingoff. Never accelerate hard when theengine is cold!

EAU16671

Shifting

Shifting gears lets you control theamount of engine power available forstarting off, accelerating, climbing hills,etc.The gear positions are shown in the il-lustration.

NOTE:To shift the transmission into the neu-tral position, press the shift pedal downrepeatedly until it reaches the end of itstravel, and then slightly raise it.

1. Shift pedal2. Neutral position



5-3

5

CAUTION:ECA10260

� Even with the transmission inthe neutral position, do notcoast for long periods of timewith the engine off, and do nottow the motorcycle for long dis-tances. The transmission isproperly lubricated only whenthe engine is running. Inade-quate lubrication may damagethe transmission.

� Always use the clutch whilechanging gears to avoid damag-ing the engine, transmission,and drive train, which are notdesigned to withstand theshock of forced shifting.

EAU16680

To start out and accelerate1. Pull the clutch lever to disengage

the clutch.2. Shift the transmission into first

gear. The neutral indicator lightshould go out.

3. Open the throttle gradually, and atthe same time, release the clutchlever slowly.

4. At the recommended shift pointsshown in the following table, closethe throttle, and at the same time,quickly pull the clutch lever in.

5. Shift the transmission into secondgear. (Make sure not to shift thetransmission into the neutral posi-tion.)

6. Open the throttle part way andgradually release the clutch lever.

7. Follow the same procedure whenshifting to the next higher gear.

NOTE:Always shift gears at the recommendedshift points.

EAU16700

To decelerate1. Apply both the front and the rear

brakes to slow the motorcycle.2. Shift the transmission into first

gear when the motorcycle reaches25 km/h (15.5 mi/h). If the engine isabout to stall or runs very roughly,pull the clutch lever in and use thebrakes to stop the motorcycle.

3. Shift the transmission into the neu-tral position when the motorcycleis almost completely stopped. Theneutral indicator light should comeon.

EAU16720

Recommended shift pointsThe recommended shift points duringacceleration and deceleration areshown in the table below.

Shift up points:1st → 2nd: 20 km/h (12.5 mi/h)2nd → 3rd: 30 km/h (19 mi/h)3rd → 4th: 40 km/h (25 mi/h)4th → 5th: 50 km/h (31 mi/h)

Shift down points:5th → 4th: 25 km/h (15.5 mi/h)4th → 3rd: 25 km/h (15.5 mi/h)3rd → 2nd: 25 km/h (15.5 mi/h)2nd → 1st: 25 km/h (15.5 mi/h)



5-4

5

EAU16841

Engine break-in There is never a more important periodin the life of your engine than the periodbetween 0 and 1600 km (1000 mi). Forthis reason, you should read the follow-ing material carefully.Since the engine is brand new, do notput an excessive load on it for the first1600 km (1000 mi). The various parts inthe engine wear and polish themselvesto the correct operating clearances.During this period, prolonged full-throt-tle operation or any condition that mightresult in engine overheating must beavoided.

EAU17121

0–1000 km (0–600 mi)Avoid prolonged operation above 4500r/min.1000–1600 km (600–1000 mi)Avoid prolonged operation above 5400r/min.

CAUTION:ECA10331

After 1000 km (600 mi) of operation,the engine oil and final gear oil mustbe changed, and the oil filter car-tridge or element replaced.

1600 km (1000 mi) and beyondThe vehicle can now be operated nor-mally.

CAUTION:ECA10310

� Keep the engine speed out ofthe tachometer red zone.

� If any engine trouble should oc-cur during the engine break-inperiod, immediately have aYamaha dealer check the vehi-cle.

EAU17212

Parking When parking, stop the engine, andthen remove the key from the mainswitch.

WARNINGEWA10310

� Since the engine and exhaustsystem can become very hot,park in a place where pedestri-ans or children are not likely totouch them.

� Do not park on a slope or on softground, otherwise the vehiclemay overturn.

CAUTION:ECA10380

Never park in an area where thereare fire hazards such as grass orother flammable materials.


PERIODIC MAINTENANCE AND MINOR REPAIR

6-1

6

EAU17231

Safety is an obligation of the owner. Pe-riodic inspection, adjustment and lubri-cation will keep your vehicle in thesafest and most efficient condition pos-sible. The most important points ofmotorcycle inspection, adjustment, andlubrication are explained on the follow-ing pages.Maintenance, replacement, or repairof the emission control devices andsystems may be performed by anyrepair establishment or individualthat is certified (if applicable).

WARNINGEWA10320

If you are not familiar with mainte-nance work, have a Yamaha dealerdo it for you.

EAU17301

PERIODIC MAINTENANCE PROPER PERIODIC MAINTENANCEOF YOUR VEHICLE IS IMPORTANTIN ORDER TO ENJOY LONG, PLEA-SURABLE SERVICE. ESPECIALLYIMPORTANT ARE THE MAINTE-NANCE SERVICES RELATED TOEMISSIONS CONTROL. THESECONTROLS NOT ONLY FUNCTIONTO ENSURE CLEANER AIR, BUTARE ALSO VITAL TO PROPER EN-GINE OPERATION AND MAXIMUMPERFORMANCE. IN THE FOLLOW-ING PERIODIC MAINTENANCECHARTS, THE SERVICES RELATEDTO EMISSIONS CONTROL AREGROUPED SEPARATELY. THESESERVICES REQUIRE SPECIALIZEDDATA, KNOWLEDGE, AND EQUIP-MENT. YAMAHA DEALERS ARETRAINED AND EQUIPPED TO PER-FORM THESE PARTICULAR SER-VICES.

EAU17350

Owner’s tool kit

The owner’s tool kit is located under therider seat. (See page 3-15.)The service information included in thismanual and the tools provided in theowner’s tool kit are intended to assistyou in the performance of preventivemaintenance and minor repairs. How-ever, additional tools such as a torquewrench may be necessary to performcertain maintenance work correctly.

NOTE:If you do not have the tools or experi-ence required for a particular job, havea Yamaha dealer perform it for you.

1. Owner’s tool kit



6-2

6

WARNINGEWA10340

Modifications not approved byYamaha may cause loss of perfor-mance, excessive emissions, andrender the vehicle unsafe for use.Consult a Yamaha dealer before at-tempting any changes.



6-3

6

EAU17600

Periodic maintenance chart for the emission control system

* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.

No. ITEM ROUTINE

INITIAL ODOMETER READINGS

600 mi (1000 km)

or 1 month

4000 mi (7000 km)

or 6 months

8000 mi (13000 km)

or 12 months

12000 mi (19000 km)

or 18 months

16000 mi (25000 km)

or 24 months

20000 mi (31000 km)

or 30 months

1 * Fuel line• Check fuel hoses for cracks or

damage.• Replace if necessary.

√ √ √ √ √

2 * Spark plugs

• Check condition.• Adjust gap and clean.• Replace every 8000 mi (13000

km) or 12 months.

√ Replace. √ Replace. √

3 * Valve clearance • Check and adjust valve clearance when engine is cold. Every 26600 mi (42000 km)

4 * Crankcase breather system

• Check breather hose for cracks or damage.

• Replace if necessary.√ √ √ √ √

5 * Fuel injection • Check and adjust engine idle speed and synchronization. √ √ √ √ √ √

6 * Exhaust system• Check for leakage.• Tighten if necessary.• Replace gasket(s) if necessary.

√ √ √ √ √

7 *Evaporative emis-sion control system (For California only)

• Check control system for dam-age.

• Replace if necessary.√

8 * Air induction sys-tem

• Check the air cut-off valve, reed valve, and hose for damage.

• Replace any damaged parts.√ √



6-4

6

EAU32185

General maintenance and lubrication chart

No. ITEM ROUTINE


600 mi (1000 km)

or 1 month

4000 mi (7000 km)

or 6 months

8000 mi (13000 km)

or 12 months

12000 mi (19000 km)

or 18 months

16000 mi (25000 km)

or 24 months

20000 mi (31000 km)

or 30 months

1 * Air filter element • Clean with compressed air.• Replace if necessary. √ √ √ √ √

2 * Clutch• Check operation and fluid leak-

age.• Correct if necessary.

√ √ √ √ √ √

3 * Front brake• Check operation, fluid level, and

for fluid leakage.• Replace brake pads if necessary.

√ √ √ √ √ √

4 * Rear brake• Check operation, fluid level, and

for fluid leakage.• Replace brake pads if necessary.

√ √ √ √ √ √

5 * Brake hoses• Check for cracks or damage. √ √ √ √ √

• Replace. Every 4 years

6 * Wheels • Check runout and for damage.• Replace if necessary. √ √ √ √ √

7 * Tires

• Check tread depth and for dam-age.

• Replace if necessary.• Check air pressure.• Correct if necessary.

√ √ √ √ √

8 * Wheel bearings• Check bearings for smooth oper-

ation.• Replace if necessary.

√ √ √ √ √



6-5

6

9 * Swingarm pivot bearings

• Check bearing assemblies for looseness.

• Moderately repack with lithium-soap-based grease.

√ Repack.

10 * Steering bearings

• Check bearing assemblies for looseness.

• Moderately repack with lithium-soap-based grease every 16000 mi (25000 km) or 24 months.

√ √ √ √ Repack. √

11 * Chassis fasteners• Check all chassis fitting and fas-

teners.• Correct if necessary.

√ √ √ √ √

12 Brake lever pivot shaft • Apply silicone grease lightly. √ √ √ √ √

13 Brake pedal pivot shaft

• Apply lithium-soap-based grease lightly. √ √ √ √ √

14 Clutch lever pivot shaft • Apply silicone grease lightly. √ √ √ √ √

15 Shift pedal pivot shaft

• Apply lithium-soap-based grease lightly. √ √ √ √ √

16 * Centerstand and sidestand pivots

• Check operation.• Apply lithium-soap-based grease

lightly.√ √ √ √ √

17 * Sidestand switch • Check operation and replace if necessary. √ √ √ √ √ √

No. ITEM ROUTINE


600 mi (1000 km)

or 1 month

4000 mi (7000 km)

or 6 months

8000 mi (13000 km)

or 12 months

12000 mi (19000 km)

or 18 months

16000 mi (25000 km)

or 24 months

20000 mi (31000 km)

or 30 months



6-6

6

18 * Front fork• Check operation and for oil leak-

age.• Replace if necessary.

√ √ √ √ √

19 * Shock absorber as-sembly

• Check operation and for oil leak-age.


20 * Rear suspension link pivots

• Apply lithium-soap-based grease lightly. √

21 Engine oil • Change (warm engine before draining). √ √ √ √ √ √

22 * Engine oil filter car-tridge • Replace. √ √ √

23 * Cooling system

• Check hoses for cracks or dam-age.


• Change with ethylene glycol anti-freeze coolant every 24 months. Change.

24 * Final gear oil

• Check oil level and for leakage.• Change at initial 600 mi (1000

km) or 1 month, and thereafter every 16000 mi (25000 km) or 24 months.

Change. √ Change.

25 * Front and rear brake switches • Check operation. √ √ √ √ √ √

No. ITEM ROUTINE


600 mi (1000 km)

or 1 month

4000 mi (7000 km)

or 6 months

8000 mi (13000 km)

or 12 months

12000 mi (19000 km)

or 18 months

16000 mi (25000 km)

or 24 months

20000 mi (31000 km)

or 30 months



6-7

6* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.

NOTE:From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months.

EAU17660

NOTE:� The air filter needs more frequent service if you are riding in unusually wet or dusty areas.� Hydraulic brake and clutch systems

• After disassembling the brake or clutch master cylinders, caliper cylinders or clutch release cylinder, always changethe fluid. Regularly check the brake and clutch fluid levels and fill the reservoirs as required.

• Replace the oil seals on the inner parts of the brake or clutch master cylinders, caliper cylinders and clutch releasecylinder every two years.

• Replace the brake and clutch hoses every four years or if cracked or damaged.

26 * Control cables• Apply Yamaha chain and cable

lube or engine oil SAE 10W-30 thoroughly.

√ √ √ √ √ √

27 * Throttle grip hous-ing and cable

• Check operation and free play.• Adjust the throttle cable free play

if necessary.• Lubricate the throttle grip housing

and cable.

√ √ √ √ √

28 * Lights, signals and switches

• Check operation.• Adjust headlight beam. √ √ √ √ √ √

No. ITEM ROUTINE


600 mi (1000 km)

or 1 month

4000 mi (7000 km)

or 6 months

8000 mi (13000 km)

or 12 months

12000 mi (19000 km)

or 18 months

16000 mi (25000 km)

or 24 months

20000 mi (31000 km)

or 30 months



6-8

6

EAU18771

Removing and installing pan-els The panels shown need to be removedto perform some of the maintenancejobs described in this chapter. Refer tothis section each time a panel needs tobe removed and installed.

EAU39550

Panel A

To remove the panelRemove the bolts and the quick fasten-er, and then take the panel off.

To install the panelPlace the panel in the original position,and then install the bolts and the quickfastener.

EAU39562

Panel B

To remove the panel1. Open the accessory box lid. (See

page 3-19.)2. Remove the bolt, screw and the

quick fasteners shown, and thentake the panel off.

1. Panel A2. Panel B3. Panel C4. Panel D

1. Panel E

1. Panel F

1. Panel A2. Bolt3. Quick fastener



6-9

6To install the panel

1. Place the panel in the original posi-tion, and then install the bolt, screwand the quick fasteners.

2. Close the accessory box lid.

EAU39570

Panel C

To remove the panel1. Remove panel A. (See page 6-8.)2. Remove the bolt and quick fasten-

er, and then remove the panel.

CAUTION:ECA15420

Do not remove the headlight beamadjusting cable.

To install the panel1. Place the panel in the original posi-

tion, and then install the bolt andquick fastener.

2. Install the panel.

EAU39582

Panel D

To remove the panel1. Remove panels B and C. (See

page 6-8.)2. Remove the bolts and quick fas-

tener shown, and then remove thepanel.

1. Panel B2. Bolt3. Screw4. Quick fastener

1. Panel C2. Bolt3. Quick fastener

1. Headlight beam adjusting cable

1. Panel C2. Panel D



6-10

6

CAUTION:ECA15420

Do not remove the headlight beamadjusting cable.


tion, and then install the bolts andquick fastener.

2. Install panels B and C.

EAU39592

Panels E and F

To remove one of the panels1. Remove the seats. (See page

3-15.)2. Remove the bolts and the quick

fastener screws, and then take thepanel off.

1. Panel D2. Bolt3. Quick fastener

1. Headlight beam adjusting cable

1. Panel D

1. Panel E2. Bolt3. Quick fastener screw

1. Panel F2. Bolt3. Quick fastener screw



6-11

6


tion, and then install the bolts andthe quick fastener screws.

2. Install the seats.

EAU19642

Checking the spark plugs The spark plugs are important enginecomponents, which should be checkedperiodically, preferably by a Yamahadealer. Since heat and deposits willcause any spark plug to slowly erode,they should be removed and checkedin accordance with the periodic mainte-nance and lubrication chart. In addition,the condition of the spark plugs can re-veal the condition of the engine.The porcelain insulator around the cen-ter electrode of each spark plug shouldbe a medium-to-light tan (the ideal colorwhen the vehicle is ridden normally),and all spark plugs installed in the en-gine should have the same color. If anyspark plug shows a distinctly differentcolor, the engine could be operating im-properly. Do not attempt to diagnosesuch problems yourself. Instead, havea Yamaha dealer check the vehicle.If a spark plug shows signs of electrodeerosion and excessive carbon or otherdeposits, it should be replaced.

Before installing a spark plug, the sparkplug gap should be measured with awire thickness gauge and, if necessary,adjusted to specification.

Clean the surface of the spark pluggasket and its mating surface, and thenwipe off any grime from the spark plugthreads.

1. Panel E

1. Panel F

Specified spark plug:NGK/CR8EDENSO/U24ESR-N

1. Spark plug gap

Spark plug gap:0.7–0.8 mm (0.028–0.031 in)



6-12

6

NOTE:If a torque wrench is not available wheninstalling a spark plug, a good estimateof the correct torque is 1/4–1/2 turnpast finger tight. However, the sparkplug should be tightened to the speci-fied torque as soon as possible.

EAU19681

Canister (for California only)

This model is equipped with a canisterto prevent the discharging of fuel vaporinto the atmosphere. Before operatingthis vehicle, make sure to check the fol-lowing:

� Check each hose connection.� Check each hose and canister for

cracks or damage. Replace if dam-aged.

� Make sure that the canister breath-er is not blocked, and if necessary,clean it.

EAU19883

Engine oil and oil filter car-tridge The engine oil level should be checkedbefore each ride. In addition, the oilmust be changed and the oil filter car-tridge replaced at the intervals speci-fied in the periodic maintenance andlubrication chart.

To check the engine oil level1. Place the vehicle on the center-

stand.

NOTE:Make sure that the vehicle is positionedstraight up when checking the oil level.A slight tilt to the side can result in afalse reading.

2. Start the engine, warm it up forseveral minutes, and then turn itoff.

3. Wait a few minutes until the oil set-tles, and then check the oil levelthrough the check window locatedat the bottom-left side of the crank-case.

Tightening torque:Spark plug:

12.5 Nm (1.25 m·kgf, 9.0 ft·lbf)



6-13

6

NOTE:The engine oil should be between theminimum and maximum level marks.

4. If the engine oil is below the mini-mum level mark, add sufficient oilof the recommended type to raiseit to the correct level.

To change the engine oil (with orwithout oil filter cartridge replace-ment)

1. Place the vehicle on a level sur-face.

2. Start the engine, warm it up forseveral minutes, and then turn itoff.

3. Place an oil pan under the engineto collect the used oil.

4. Remove the engine oil filler capand drain bolt to drain the oil fromthe crankcase.

NOTE:Skip steps 5–7 if the oil filter cartridge isnot being replaced.

5. Remove the oil filter cartridge withan oil filter wrench.

NOTE:An oil filter wrench is available at aYamaha dealer.

6. Apply a thin coat of engine oil tothe O-ring of the new oil filter car-tridge.

1. Engine oil level check window2. Maximum level mark3. Minimum level mark

1. Engine oil filler cap2. Oil filter cartridge3. Engine oil drain bolt

1. Oil filter cartridge2. Oil filter wrench



6-14

6

NOTE:Make sure that the O-ring is properlyseated.

7. Install the new oil filter cartridge,and then tighten it to the specifiedtorque with a torque wrench.

8. Install the engine oil drain bolt, andthen tighten it to the specifiedtorque.

NOTE:Check the washer for damage and re-place it if necessary.

9. Refill with the specified amount ofthe recommended engine oil, andthen install and tighten the oil fillercap.

NOTE:Be sure to wipe off spilled oil on anyparts after the engine and exhaust sys-tem have cooled down.

CAUTION:ECA11620

� In order to prevent clutch slip-page (since the engine oil alsolubricates the clutch), do notmix any chemical additives. Donot use oils with a diesel speci-fication of “CD” or oils of a high-er quality than specified. Inaddition, do not use oils labeled“ENERGY CONSERVING II” orhigher.

� Make sure that no foreign mate-rial enters the crankcase.

1. O-ring

1. Oil filter cartridge2. Torque wrench

Tightening torque:Oil filter cartridge:

17 Nm (1.7 m·kgf, 12 ft·lbf)

Tightening torque:Engine oil drain bolt:

43 Nm (4.3 m·kgf, 31 ft·lbf)

Recommended engine oil:See page 8-1.

Oil quantity:Without oil filter cartridge replace-ment:

3.80 L (4.02 US qt) (3.34 Imp.qt)With oil filter cartridge replacement:

4.00 L (4.23 US qt) (3.52 Imp.qt)



6-15

6

10. Start the engine, and then let it idlefor several minutes while checkingit for oil leakage. If oil is leaking, im-mediately turn the engine off andcheck for the cause.

NOTE:After the engine is started, the engineoil level warning light should go off if theoil level is sufficient.

CAUTION:ECA10400

If the oil level warning light flickersor remains on, immediately turn theengine off and have a Yamaha dealercheck the vehicle.

11. Turn the engine off, and thencheck the oil level and correct it ifnecessary.

EAU20014

Final gear oil The final gear case must be checkedfor oil leakage before each ride. If anyleakage is found, have a Yamaha deal-er check and repair the vehicle. In addi-tion, the final gear oil must be changedas follows at the intervals specified inthe periodic maintenance and lubrica-tion chart.

WARNINGEWA10370

� Make sure that no foreign mate-rial enters the final gear case.

� Make sure that no oil gets on thetire or wheel.

To check the final gear oil level1. Place the vehicle on the center-

stand.

NOTE:� The final gear oil level must be

checked on a cold engine.� Make sure that the vehicle is posi-

tioned straight up when checkingthe oil level. A slight tilt to the sidecan result in a false reading.

1. “CD” specification2. “ENERGY CONSERVING II”

1

2



6-16

6

2. Remove the final gear oil filler bolt,and then check the oil level in thefinal gear case.

NOTE:The oil level should be at the brim of thefiller hole.

3. If the oil is below the brim of the fill-er hole, add sufficient oil of the rec-ommended type to raise it to thecorrect level.

4. Install the oil filler bolt, and thentighten it to the specified torque.

To change the final gear oil1. Place the vehicle on a level sur-

face.2. Place an oil pan under the final

gear case to collect the used oil.3. Remove the oil filler bolt and drain

bolt to drain the oil from the finalgear case.

4. Install the final gear oil drain bolt,and then tighten it to the specifiedtorque.

5. Refill with the recommended finalgear oil to the brim of the filler hole.

6. Install the oil filler bolt, and thentighten it to the specified torque.

7. Check the final gear case for oilleakage. If oil is leaking, check forthe cause.

1. Final gear oil filler bolt2. Final gear oil drain bolt3. Correct oil level

Tightening torque:Final gear oil filler bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

Tightening torque:Final gear oil drain bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

Recommended final gear oil:Shaft drive gear oil (Part No.: 9079E-SH001-00)

Oil quantity:0.20 L (0.21 US qt) (0.18 Imp.qt)

Tightening torque:Final gear oil filler bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)



6-17

6

EAU20070

Coolant The coolant level should be checkedbefore each ride. In addition, the cool-ant must be changed at the intervalsspecified in the periodic maintenanceand lubrication chart.

EAU39512

To check the coolant levelThe coolant level should be checked asfollows before each ride. In addition,the coolant must be changed at the in-tervals specified in the periodic mainte-nance and lubrication chart.

1. Place the vehicle on the center-stand.

NOTE:� The coolant level must be checked

on a cold engine since the levelvaries with engine temperature.

� Make sure that the vehicle is posi-tioned straight up when checkingthe coolant level. A slight tilt to theside can result in a false reading.

2. Check the coolant level in the cool-ant reservoir.

NOTE:The coolant should be between theminimum and maximum level marks.

3. If the coolant is at or below theminimum level mark, remove thecoolant reservoir cap.

4. Add coolant or distilled water toraise the coolant to the maximumlevel mark, install the coolant res-ervoir cap.

CAUTION:ECA10471

� If coolant is not available, usedistilled water or soft tap waterinstead. Do not use hard wateror salt water since it is harmfulto the engine.

� If water has been used insteadof coolant, replace it with cool-ant as soon as possible, other-

1. Maximum level mark2. Minimum level mark

1. Coolant reservoir cap

Coolant reservoir capacity (up to the maximum level mark):

0.25 L (0.26 US qt) (0.22 Imp.qt)



6-18

6

wise the cooling system will notbe protected against frost andcorrosion.

� If water has been added to thecoolant, have a Yamaha dealercheck the antifreeze content ofthe coolant as soon as possible,otherwise the effectiveness ofthe coolant will be reduced.

WARNINGEWA10380

Never attempt to remove the radiatorcap when the engine is hot.

NOTE:� The radiator fans are automatically

switched on or off according to thecoolant temperature in the radia-tor.

� If the engine overheats, see page6-39 for further instructions.

EAU33030

Changing the coolant

WARNINGEWA10380

Never attempt to remove the radiatorcap when the engine is hot.

The coolant must be changed at the in-tervals specified in the periodic mainte-nance and lubrication chart. Have aYamaha dealer change the coolant.

EAU20471

Cleaning the air filter element The air filter element should be cleanedat the intervals specified in the periodicmaintenance and lubrication chart.Clean the air filter element more fre-quently if you are riding in unusuallywet or dusty areas.

1. Remove panel E. (See page 6-8.)2. Remove the intake air shroud by

removing the screw and the quickfastener screws.

3. Remove the air filter case cover byremoving the screws.

1. Intake air shroud2. Screw3. Quick fastener screw



6-19

6

4. Pull the air filter element out.

5. Lightly tap the air filter element toremove most of the dust and dirt,and then blow the remaining dirt

out with compressed air as shown.If the air filter element is damaged,replace it.

6. Insert the air filter element into theair filter case.

CAUTION:ECA10480

� Make sure that the air filter ele-ment is properly seated in theair filter case.

� The engine should never be op-erated without the air filter ele-ment installed, otherwise thepiston(s) and/or cylinder(s) maybecome excessively worn.

7. Install the air filter case cover by in-stalling the screws.

CAUTION:ECA15410

Make sure that the fuel tank breath-er/overflow hose is not pinched.

8. Install the intake air shroud by in-stalling the screw and the quickfastener screws.

9. Install the panel.

1. Air filter case cover2. Screw

1. Air filter element

1. Fuel tank breather/overflow hose



6-20

6

EAU44730

Checking the engine idling speed The engine idling speed must bechecked as follows and, if necessary,adjusted by a Yamaha dealer at the in-tervals specified in the periodic mainte-nance and lubrication chart.Start the engine and warm it up for sev-eral minutes at 1000–2000 r/min whileoccasionally revving it to 4000–5000r/min.

EAU21382

Checking the throttle cable free play

The throttle cable free play should mea-sure 3.0–5.0 mm (0.12–0.20 in) at thethrottle grip. Periodically check thethrottle cable free play and, if neces-sary, have a Yamaha dealer adjust it.

EAU21401

Valve clearance The valve clearance changes with use,resulting in improper air-fuel mixtureand/or engine noise. To prevent thisfrom occurring, the valve clearancemust be adjusted by a Yamaha dealerat the intervals specified in the periodicmaintenance and lubrication chart.

Engine idling speed:1000–1100 r/min

1. Throttle cable free play



6-21

6

EAU21750

Tires To maximize the performance, durabil-ity, and safe operation of your motor-cycle, note the following pointsregarding the specified tires.

Tire air pressureThe tire air pressure should be checkedand, if necessary, adjusted before eachride.

WARNINGEWA10500

� The tire air pressure must bechecked and adjusted on coldtires (i.e., when the temperatureof the tires equals the ambienttemperature).

� The tire air pressure must be ad-justed in accordance with theriding speed and with the totalweight of rider, passenger, car-go, and accessories approvedfor this model.

WARNINGEWA10510

Proper loading of your vehicle is im-portant for several characteristics ofyour vehicle, such as handling,braking, performance and safety. Donot carry loosely packed items thatcan shift. Securely pack your heavi-

est items close to the center of thevehicle, and distribute the weightevenly from side to side. Properlyadjust the suspension for your load,and check the condition and pres-sure of your tires. NEVER OVER-LOAD YOUR VEHICLE. Make surethat the total weight of the cargo, rid-er, passenger, and accessories(cowling, saddlebags, etc. if ap-proved for this model) does not ex-ceed the maximum load of thevehicle. Operation of an overloadedvehicle could cause tire damage, anaccident, or even injury.

Tire air pressure (measured on cold tires):

0–90 kg (0–198 lb):Front:

270 kPa (39 psi) (2.70 kgf/cm²)Rear:

290 kPa (42 psi) (2.90 kgf/cm²)90–211 kg (198–465 lb) (CAL)90–212 kg (198–467 lb) (U49):

Front:270 kPa (39 psi) (2.70 kgf/cm²)

Rear:290 kPa (42 psi) (2.90 kgf/cm²)

High-speed riding:Front:


290 kPa (42 psi) (2.90 kgf/cm²)Maximum load*:

211 kg (465 lb) (CAL)212 kg (467 lb) (U49)

* Total weight of rider, passenger, car-go and accessories



6-22

6

Tire inspection

Always check the tires before operatingthe motorcycle. If a tire tread showscrosswise lines (minimum tread depth),if the tire has a nail or glass fragmentsin it, or if the sidewall is cracked, con-tact a Yamaha dealer immediately andhave the tire replaced.

WARNINGEWA10580

� It is dangerous to ride with aworn-out tire. When a tire treadbegins to show crosswise lines,have a Yamaha dealer replacethe tire immediately.

� The replacement of all wheel-and brake-related parts, includ-ing the tires, should be left to aYamaha dealer, who has thenecessary professional knowl-edge and experience.

Tire information

This motorcycle is equipped with castwheels and tubeless tires with valves.

WARNINGEWA10480

� The front and rear tires shouldbe of the same make and de-sign, otherwise the handlingcharacteristics of the motor-cycle cannot be guaranteed.

� After extensive tests, only thetires listed below have been ap-proved for this model byYamaha Motor Co., Ltd.

� Always make sure that the valvecaps are securely installed toprevent air pressure leakage.

� Use only the tire valves andvalve cores listed below toavoid tire deflation during ahigh-speed ride.

1. Tire sidewall2. Tire wear indicator3. Tire tread depth

Minimum tire tread depth (front and rear):

1.0 mm (0.04 in)

1. Tire air valve2. Tire air valve core3. Tire air valve cap with seal



6-23

6

WARNINGEWA10600

This motorcycle is fitted with super-high-speed tires. Note the followingpoints in order to make the most ef-ficient use of these tires.

� Use only the specified replace-ment tires. Other tires may runthe danger of bursting at superhigh speeds.

� Brand-new tires can have a rela-tively poor grip on certain roadsurfaces until they have been

“broken in”. Therefore, it is ad-visable before doing any high-speed riding to ride conserva-tively for approximately 100 km(60 mi) after installing a new tire.

� The tires must be warmed upbefore a high-speed run.

� Always adjust the tire air pres-sure according to the operatingconditions.

EAU21960

Cast wheels To maximize the performance, durabil-ity, and safe operation of your vehicle,note the following points regarding thespecified wheels.

� The wheel rims should be checkedfor cracks, bends or warpage be-fore each ride. If any damage isfound, have a Yamaha dealer re-place the wheel. Do not attempteven the smallest repair to thewheel. A deformed or crackedwheel must be replaced.

� The wheel should be balancedwhenever either the tire or wheelhas been changed or replaced. Anunbalanced wheel can result inpoor performance, adverse han-dling characteristics, and a short-ened tire life.

� Ride at moderate speeds afterchanging a tire since the tire sur-face must first be “broken in” for itto develop its optimal characteris-tics.

Front tire:Size:

120/70 ZR17M/C (58W)Manufacturer/model:

METZELER/Roadtec Z6GBRIDGESTONE/BT021F F

Rear tire:Size:


METZELER/Roadtec Z6CBRIDGESTONE/BT021R F

FRONT and REAR:Tire air valve:

TR412Valve core:

#9100 (original)



6-24

6

EAU22011

Accessories and replacement parts

WARNINGEWA10621

This vehicle is not designed to pull atrailer or to be attached to a sidecar.The accessories or replacementparts you choose for your vehicleshould be designed specifically forthis model, and they must be se-curely mounted to maintain the in-herent stability of the originaldesign. Genuine Yamaha Parts andAccessories are designed and test-ed to be compatible with your vehi-cle. Please consider GenuineYamaha Parts and Accessories be-fore making a purchase. Use of non-Yamaha-approved accessories orreplacement parts may cause loss ofhandling stability and riding safety.Since Yamaha cannot control thequality of accessories or parts man-ufactured by other companies,Yamaha cannot be held liable for

any consequences caused by theuse of items which have not beenapproved by Yamaha.

EAU22072

Clutch lever Since this model is equipped with a hy-draulic clutch, adjusting the clutch leverfree play is not needed. However, it isnecessary to check the clutch fluid leveland check the hydraulic system forleakage before each ride. If the clutchlever free play does become excessive,and shifting becomes rough or clutchslippage occurs, causing poor acceler-ation, there may be air in the clutch sys-tem. If there is air in the hydraulicsystem, have a Yamaha dealer bleedthe system before operating the motor-cycle.



6-25

6

EAU36501

Rear brake light switch The rear brake light switch, which is ac-tivated by the brake pedal, is properlyadjusted when the brake light comeson just before braking takes effect. Ifnecessary, have a Yamaha dealer ad-just the brake light switch.

EAU22390

Checking the front and rear brake pads The front and rear brake pads must bechecked for wear at the intervals spec-ified in the periodic maintenance andlubrication chart.

EAU43431

Front brake pads

The front brake calipers are equippedwith two sets of brake pads.Each front brake pad is provided with awear indicator groove, which allowsyou to check the brake pad wear with-out having to disassemble the brake.To check a brake pad for wear, checkits wear indicator groove. If a brake padhas worn to the point that the wear indi-

cator groove has almost disappeared,have a Yamaha dealer replace thebrake pads as a set.

EAU22500

Rear brake pads

Check each rear brake pad for damageand measure the lining thickness. If abrake pad is damaged or if the liningthickness is less than 0.8 mm (0.03 in),have a Yamaha dealer replace thebrake pads as a set.

1. Brake pad wear indicator groove

1. Lining thickness



6-26

6

EAU40270

Checking the brake and clutch fluid levels

Front brake

Rear brake

Clutch

Insufficient brake fluid may allow air toenter the brake or clutch systems, pos-sibly causing them to become ineffec-tive.Before riding, check that the brake fluidis above the minimum level mark andreplenish if necessary. A low brake fluidlevel may indicate worn brake padsand/or brake system leakage. If thebrake level is low, be sure to check thebrake pads for wear and the brake sys-tem for leakage.

NOTE:The rear brake fluid reservoir is locatedbehind panel F. (See page 6-8.)

Observe these precautions:

� When checking the fluid level,make sure that the top of the brakeor clutch fluid reservoir is level.

� Use only the recommended qualitybrake fluid, otherwise the rubberseals may deteriorate, causingleakage and poor braking or clutchperformance.

� Refill with the same type of brakefluid. Mixing fluids may result in aharmful chemical reaction andlead to poor braking or clutch per-formance.

� The brake or clutch fluid reservoirdiaphragm will lose its shape fromthe negative pressure if the fluidlevel goes down too far. Be sure toreturn the diaphragm to its originalshape before installing it into thebrake or clutch fluid reservoir.

� Be careful that water or dust doesnot enter the brake or clutch fluidreservoir when refilling. Water willsignificantly lower the boiling point

1. Minimum level mark



Recommended brake and clutch flu-id:

DOT 4 brake fluid



6-27

6

of the fluid and may result in vaporlock, and dirt may clog the ABS hy-draulic unit valves.

� Brake fluid may deteriorate paint-ed surfaces or plastic parts. Al-ways clean up spilled fluidimmediately.

� As the brake pads wear, it is nor-mal for the brake fluid level to grad-ually go down. However, if thebrake fluid level goes down sud-denly, have a Yamaha dealercheck the cause.

EAU22750

Changing the brake and clutch fluids Have a Yamaha dealer change thebrake and clutch fluids at the intervalsspecified in the NOTE after the periodicmaintenance and lubrication chart. Inaddition, have the oil seals of the brakeand clutch master cylinders and cali-pers as well as the brake and clutchhoses replaced at the intervals listedbelow or whenever they are damagedor leaking.

� Oil seals: Replace every twoyears.

� Brake and clutch hoses: Replaceevery four years.

EAU23091

Checking and lubricating the cables The operation of all control cables andthe condition of the cables should bechecked before each ride, and the ca-bles and cable ends should be lubricat-ed if necessary. If a cable is damagedor does not move smoothly, have aYamaha dealer check or replace it.

WARNINGEWA10710

Damage to the outer housing of ca-bles may result in internal rustingand cause interference with cablemovement. Replace damaged ca-bles as soon as possible to preventunsafe conditions.

Recommended lubricant:Yamaha Chain and Cable Lube or engine oil SAE 10W-30



6-28

6

EAU23111

Checking and lubricating the throttle grip and cable The operation of the throttle grip shouldbe checked before each ride. In addi-tion, the cable should be lubricated atthe intervals specified in the periodicmaintenance chart.

EAU44271

Checking and lubricating the brake and shift pedals

The operation of the brake and shiftpedals should be checked before eachride, and the pedal pivots should be lu-bricated if necessary.

Recommended lubricant:Lithium-soap-based grease



6-29

6

EAU43600

Checking and lubricating the brake and clutch levers

Brake lever

Clutch lever

The operation of the brake and clutchlevers should be checked before eachride, and the lever pivots should be lu-bricated if necessary.

EAU23212

Checking and lubricating the centerstand and sidestand

The operation of the centerstand andsidestand should be checked beforeeach ride, and the pivots and metal-to-metal contact surfaces should be lubri-cated if necessary.

WARNINGEWA10740

If the centerstand or sidestand doesnot move up and down smoothly,have a Yamaha dealer check or re-pair it.

Recommended lubricant:Silicone grease

Recommended lubricant:Lithium-soap-based grease



6-30

6

EAUM1650

Lubricating the swingarm piv-ots

The swingarm pivots must be lubricat-ed at the intervals specified in the peri-odic maintenance and lubrication chart.

EAU23250

Lubricating the rear suspen-sion

The pivoting points of the rear suspen-sion must be lubricated at the intervalsspecified in the periodic maintenanceand lubrication chart.

EAU23271

Checking the front fork The condition and operation of the frontfork must be checked as follows at theintervals specified in the periodic main-tenance and lubrication chart.

To check the condition

WARNINGEWA10750

Securely support the vehicle so thatthere is no danger of it falling over.

Check the inner tubes for scratches,damage and excessive oil leakage.

To check the operation1. Place the vehicle on a level sur-

face and hold it in an upright posi-tion.

2. While applying the front brake,push down hard on the handlebarsseveral times to check if the frontfork compresses and reboundssmoothly.

Recommended lubricant:Lithium-soap-based grease Recommended lubricant:

Lithium-soap-based grease



6-31

6

CAUTION:ECA10590

If any damage is found or the frontfork does not operate smoothly,have a Yamaha dealer check or re-pair it.

EAU23280

Checking the steering Worn or loose steering bearings maycause danger. Therefore, the operationof the steering must be checked as fol-lows at the intervals specified in the pe-riodic maintenance and lubricationchart.

1. Place a stand under the engine toraise the front wheel off theground.

WARNINGEWA10750

Securely support the vehicle so thatthere is no danger of it falling over.

2. Hold the lower ends of the frontfork legs and try to move them for-ward and backward. If any freeplay can be felt, have a Yamahadealer check or repair the steering.



6-32

6

EAU23290

Checking the wheel bearings The front and rear wheel bearings mustbe checked at the intervals specified inthe periodic maintenance and lubrica-tion chart. If there is play in the wheelhub or if the wheel does not turnsmoothly, have a Yamaha dealer checkthe wheel bearings.

EAU39521

Battery

The battery is located under panel A.(See page 6-8.)This vehicle is equipped with a sealed-type (MF) battery, which does not re-quire any maintenance. There is noneed to check the electrolyte or to adddistilled water.

To charge the batteryHave a Yamaha dealer charge the bat-tery as soon as possible if it seems tohave discharged. Keep in mind that the

battery tends to discharge more quicklyif the vehicle is equipped with optionalelectrical accessories.

WARNINGEWA10760

� Electrolyte is poisonous anddangerous since it contains sul-furic acid, which causes severeburns. Avoid any contact withskin, eyes or clothing and al-ways shield your eyes whenworking near batteries. In caseof contact, administer the fol-lowing FIRST AID.• EXTERNAL: Flush with plenty

of water.• INTERNAL: Drink large quan-

tities of water or milk and im-mediately call a physician.

• EYES: Flush with water for 15minutes and seek promptmedical attention.

� Batteries produce explosive hy-drogen gas. Therefore, keepsparks, flames, cigarettes, etc.,away from the battery and pro-vide sufficient ventilation whencharging it in an enclosedspace.

1. Battery2. Positive battery lead (red)3. Negative battery lead (black)



6-33

6

� KEEP THIS AND ALL BATTER-IES OUT OF THE REACH OFCHILDREN.

To store the battery1. If the vehicle will not be used for

more than one month, remove thebattery, fully charge it, and thenplace it in a cool, dry place.

2. If the battery will be stored for morethan two months, check it at leastonce a month and fully charge it ifnecessary.

3. Fully charge the battery before in-stallation.

4. After installation, make sure thatthe battery leads are properly con-nected to the battery terminals.

CAUTION:ECA10630

� Always keep the batterycharged. Storing a dischargedbattery can cause permanentbattery damage.

� To charge a sealed-type (MF)battery, a special (constant-volt-age) battery charger is required.Using a conventional battery

charger will damage the battery.If you do not have access to asealed-type (MF) battery charg-er, have a Yamaha dealercharge your battery.

EAU23658

Replacing the fuses The main fuse, the fuse boxes and theABS motor fuse are located under pan-el A. (See page 6-8.)

1. Main fuse2. Fuse box3. ABS motor fuse4. ABS motor spare fuse



6-34

6

If a fuse is blown, replace it as follows.1. Turn the key to “OFF” and turn off

the electrical circuit in question.2. Remove the blown fuse, and then

install a new fuse of the specifiedamperage.

CAUTION:ECA10640

Do not use a fuse of a higher amper-age rating than recommended toavoid causing extensive damage tothe electrical system and possibly afire.

3. Turn the key to “ON” and turn onthe electrical circuit in question tocheck if the device operates.

4. If the fuse immediately blowsagain, have a Yamaha dealercheck the electrical system.

1. Fuse box2. Right radiator fan fuse3. Left radiator fan fuse4. Hazard fuse5. Backup fuse (for odometer and clock)6. ABS solenoid fuse7. Fuel injection system fuse8. Headlight fuse9. Signaling system fuse10.ABS control unit fuse11.Ignition fuse12.Auxiliary DC jack fuse13.Spare fuse

Specified fuses:Main fuse:

50.0 AHeadlight fuse:

25.0 ASignaling system fuse:

15.0 AIgnition fuse:

10.0 ARadiator fan fuse:

15.0 A × 2Backup fuse:

10.0 AHazard fuse:

10.0 AFuel injection system fuse:

15.0 AABS solenoid fuse:

20.0 AABS control unit fuse:

10.0 AAuxiliary DC jack fuse:

3.0 AABS motor fuse:

30.0 A



6-35

6

EAU23900

Replacing a headlight bulb This model is equipped with quartz bulbheadlights. If a headlight bulb burnsout, replace it as follows.

1. Remove panel D (if replacing theleft headlight bulb) or panel C (if re-placing the right headlight bulb).(See page 6-8.)

2. Disconnect the headlight coupler,and then remove the headlightbulb cover.

3. Unhook the headlight bulb holder,and then remove the defectivebulb.

WARNINGEWA10790

Headlight bulbs get very hot. There-fore, keep flammable products awayfrom a lit headlight bulb, and do nottouch the bulb until it has cooleddown.

4. Place a new headlight bulb into po-sition, and then secure it with thebulb holder.

CAUTION:ECA10650

Take care not to damage the follow-ing parts:

� Headlight bulbDo not touch the glass part ofthe headlight bulb to keep it freefrom oil, otherwise the transpar-ency of the glass, the luminosityof the bulb, and the bulb life willbe adversely affected. Thor-oughly clean off any dirt and fin-gerprints on the headlight bulbusing a cloth moistened with al-cohol or thinner.

� Headlight lensDo not affix any type of tintedfilm or stickers to the headlightlens.Do not use a headlight bulb of awattage higher than specified.

1. Headlight coupler2. Headlight bulb cover

1. Headlight bulb holder2. Headlight bulb

1. Do not touch the glass part of the bulb.



6-36

6

5. Install the headlight bulb cover,and then connect the coupler.

6. Install the panel.7. Have a Yamaha dealer adjust the

headlight beam if necessary.

EAU39880

Front turn signal light If a front turn signal light does not comeon, have a Yamaha dealer check itselectrical circuit or replace the bulb.

EAU27001

Replacing a rear turn signal light bulb or a tail/brake light bulb

1. Remove the passenger seat. (Seepage 3-15.)

2. Remove the socket (together withthe bulb) by turning it counter-clockwise.

3. Remove the defective bulb bypushing it in and turning it counter-clockwise.

4. Insert a new bulb into the socket,push it in, and then turn it clock-wise until it stops.

5. Install the socket (together with thebulb) by turning it clockwise.

1. Turn signal light bulb socket2. Tail/brake light bulb socket



6-37

6

6. Install the passenger seat. EAU24310

Replacing the license plate light bulb

1. Remove the license plate light unitby removing the screws.

2. Remove the socket (together withthe bulb) by pulling it out.

3. Remove the defective bulb by pull-ing it out.

4. Insert a new bulb into the socket.5. Install the socket (together with the

bulb) by pushing it in.6. Install the license plate light unit by

installing the screws.

1. Screw2. License plate light unit

1. License plate light bulb



6-38

6

EAU25870

Troubleshooting Although Yamaha motorcycles receivea thorough inspection before shipmentfrom the factory, trouble may occur dur-ing operation. Any problem in the fuel,compression, or ignition systems, forexample, can cause poor starting andloss of power.The following troubleshooting chartsrepresent quick and easy proceduresfor checking these vital systems your-self. However, should your motorcyclerequire any repair, take it to a Yamahadealer, whose skilled technicians havethe necessary tools, experience, andknow-how to service the motorcycleproperly.Use only genuine Yamaha replace-ment parts. Imitation parts may look likeYamaha parts, but they are often inferi-or, have a shorter service life and canlead to expensive repair bills.



6-39

6

EAU42500

Troubleshooting charts

Starting problems or poor engine performance

WARNINGEWA10840

Keep away open flames and do not smoke while checking or working on the fuel system.

Check the fuel level inthe fuel tank.

1. FuelThere is enough fuel.

There is no fuel.

Check the compression.

Supply fuel. The engine does not start. Check the compression.

Operate the electric starter.

2. CompressionThere is compression.

There is no compression.

Check the ignition.

Have a Yamaha dealercheck the vehicle.

Remove the spark plugsand check the electrodes.

3. Ignition Wipe off with a dry cloth and correct thespark plug gaps, or replace the spark plugs.

Have a Yamaha dealer check the vehicle.

The engine does not start.Have a Yamaha dealercheck the vehicle.

The engine does not start.Check the battery.

Operate the electric starter.

4. BatteryThe engine turns over quickly.

The engine turns over slowly.

The battery is good.

Check the battery lead connections,and charge the battery if necessary.

Dry

Wet Operate the electric starter.



6-40

6

Engine overheating

WARNINGEWAT1040

� Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may beblown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.

� Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the de-tent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the capwhile turning it counterclockwise, and then remove the cap.

NOTE:If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolantas soon as possible.

Wait until the engine has cooled.

Check the coolant level in the reservoir and radiator.

The coolant level is OK.

The coolant level is low.Check the cooling systemfor leakage.

Have a Yamaha dealer checkand repair the cooling system.

Add coolant. (See NOTE.)

Start the engine. If the engine overheats again, have a Yamaha dealer check and repair the cooling system.

There isleakage.

There is no leakage.


MOTORCYCLE CARE AND STORAGE

7-1

7

EAU37833

Matte color caution

CAUTION:ECA15192

Some models are equipped withmatte colored finished parts. Besure to consult a Yamaha dealer foradvice on what products to use be-fore cleaning the vehicle. Using abrush, harsh chemical products orcleaning compounds when cleaningthese parts will scratch or damagetheir surface. Wax also should notbe applied to any matte colored fin-ished parts.

EAU26061

Care While the open design of a motorcyclereveals the attractiveness of the tech-nology, it also makes it more vulnera-ble. Rust and corrosion can developeven if high-quality components areused. A rusty exhaust pipe may go un-noticed on a car, however, it detractsfrom the overall appearance of a motor-cycle. Frequent and proper care doesnot only comply with the terms of thewarranty, but it will also keep yourmotorcycle looking good, extend its lifeand optimize its performance.

Before cleaning1. Cover the muffler outlets with plas-

tic bags after the engine hascooled down.

2. Make sure that all caps and coversas well as all electrical couplersand connectors, including thespark plug caps, are tightly in-stalled.

3. Remove extremely stubborn dirt,like oil burnt onto the crankcase,with a degreasing agent and abrush, but never apply such prod-

ucts onto seals, gaskets and wheelaxles. Always rinse the dirt and de-greaser off with water.

Cleaning

CAUTION:ECA10771

� Avoid using strong acidic wheelcleaners, especially on spokedwheels. If such products areused on hard-to-remove dirt, donot leave the cleaner on the af-fected area any longer than in-structed. Also, thoroughly rinsethe area off with water, immedi-ately dry it, and then apply a cor-rosion protection spray.

� Improper cleaning can damageplastic parts such as cowlings,panels, windshields, headlightlenses, meter lenses, etc. Useonly a soft, clean cloth orsponge with mild detergent andwater to clean plastic.

� Do not use any harsh chemicalproducts on plastic parts. Besure to avoid using cloths orsponges which have been incontact with strong or abrasive



7-2

7

cleaning products, solvent orthinner, fuel (gasoline), rust re-movers or inhibitors, brake flu-id, antifreeze or electrolyte.

� Do not use high-pressure wash-ers or steam-jet cleaners sincethey cause water seepage anddeterioration in the following ar-eas: seals (of wheel and swing-arm bearings, fork and brakes),electric components (couplers,connectors, instruments,switches and lights), breatherhoses and vents.

� For motorcycles equipped witha windshield: Do not use strongcleaners or hard sponges asthey will cause dulling orscratching. Some cleaning com-pounds for plastic may leavescratches on the windshield.Test the product on a small hid-den part of the windshield tomake sure that it does not leaveany marks. If the windshield isscratched, use a quality plasticpolishing compound afterwashing.

After normal useRemove dirt with warm water, a milddetergent, and a soft, clean sponge,and then rinse thoroughly with cleanwater. Use a toothbrush or bottlebrushfor hard-to-reach areas. Stubborn dirtand insects will come off more easily ifthe area is covered with a wet cloth fora few minutes before cleaning.

After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roadsduring winter are extremely corrosive incombination with water, carry out thefollowing steps after each ride in therain, near the sea or on salt-sprayedroads.

NOTE:Salt sprayed on roads in the winter mayremain well into spring.

1. Clean the motorcycle with cold wa-ter and a mild detergent, after theengine has cooled down.

CAUTION:ECA10790

Do not use warm water since it in-creases the corrosive action of thesalt.

2. After drying the motorcycle, applya corrosion protection spray on allmetal, including chrome- and nick-el-plated, surfaces to prevent cor-rosion.

After cleaning1. Dry the motorcycle with a chamois

or an absorbing cloth.2. Use a chrome polish to shine

chrome, aluminum and stainless-steel parts, including the exhaustsystem. (Even the thermally in-duced discoloring of stainless-steel exhaust systems can be re-moved through polishing.)

3. To prevent corrosion, it is recom-mended to apply a corrosion pro-tection spray on all metal,including chrome- and nickel-plat-ed, surfaces.

4. Use spray oil as a universal clean-er to remove any remaining dirt.



7-3

7

5. Touch up minor paint damagecaused by stones, etc.

6. Wax all painted surfaces.7. Let the motorcycle dry completely

before storing or covering it.

WARNINGEWA11130

� Make sure that there is no oil orwax on the brakes or tires.

� If necessary, clean the brakediscs and brake linings with aregular brake disc cleaner or ac-etone, and wash the tires withwarm water and a mild deter-gent. Before riding at higherspeeds, test the motorcycle’sbraking performance and cor-nering behavior.

CAUTION:ECA10800

� Apply spray oil and wax spar-ingly and make sure to wipe offany excess.

� Never apply oil or wax to anyrubber and plastic parts, buttreat them with a suitable careproduct.

� Avoid using abrasive polishingcompounds as they will wearaway the paint.

NOTE:Consult a Yamaha dealer for advice onwhat products to use.

EAU26241

Storage

Short-termAlways store your motorcycle in a cool,dry place and, if necessary, protect itagainst dust with a porous cover.

CAUTION:ECA10810

� Storing the motorcycle in apoorly ventilated room or cover-ing it with a tarp, while it is stillwet, will allow water and humid-ity to seep in and cause rust.

� To prevent corrosion, avoiddamp cellars, stables (becauseof the presence of ammonia)and areas where strong chemi-cals are stored.

Long-termBefore storing your motorcycle for sev-eral months:

1. Follow all the instructions in the“Care” section of this chapter.

2. Fill up the fuel tank and add fuelstabilizer (if available) to preventthe fuel tank from rusting and thefuel from deteriorating.



7-4

7

3. Perform the following steps to pro-tect the cylinders, piston rings, etc.from corrosion.a. Remove the spark plug caps

and spark plugs.b. Pour a teaspoonful of engine oil

into each spark plug bore.c. Install the spark plug caps onto

the spark plugs, and then placethe spark plugs on the cylinderhead so that the electrodes aregrounded. (This will limit spark-ing during the next step.)

d. Turn the engine over severaltimes with the starter. (This willcoat the cylinder walls with oil.)

e. Remove the spark plug capsfrom the spark plugs, and theninstall the spark plugs and thespark plug caps.

WARNINGEWA10950

To prevent damage or injury fromsparking, make sure to ground thespark plug electrodes while turningthe engine over.

4. Lubricate all control cables and thepivoting points of all levers andpedals as well as of the side-stand/centerstand.

5. Check and, if necessary, correctthe tire air pressure, and then liftthe motorcycle so that both of itswheels are off the ground. Alterna-tively, turn the wheels a little everymonth in order to prevent the tiresfrom becoming degraded in onespot.

6. Cover the muffler outlets with plas-tic bags to prevent moisture fromentering them.

7. Remove the battery and fullycharge it. Store it in a cool, dryplace and charge it once a month.Do not store the battery in an ex-cessively cold or warm place [lessthan 0 °C (30 °F) or more than 30°C (90 °F)]. For more informationon storing the battery, see page6-32.

NOTE:Make any necessary repairs beforestoring the motorcycle.


SPECIFICATIONS

8-1

8

Dimensions:Overall length:

2230 mm (87.8 in)Overall width:

750 mm (29.5 in)Overall height:

1450 mm (57.1 in)Seat height:

805 mm (31.7 in)Wheelbase:

1545 mm (60.8 in)Ground clearance:

130 mm (5.12 in)Minimum turning radius:

3100 mm (122.0 in)Weight:

With oil and fuel:291.0 kg (642 lb) (U49)292.0 kg (644 lb) (CAL)

Engine:Engine type:

Liquid cooled 4-stroke, DOHCCylinder arrangement:

Forward-inclined parallel 4-cylinderDisplacement:

1298.0 cm³Bore × stroke:

79.0 × 66.2 mm (3.11 × 2.61 in)Compression ratio:

10.80 :1Starting system:

Electric starterLubrication system:

Wet sump

Engine oil:Type:

YAMALUBE 4 (20W-40) or SAE 20W-40Recommended engine oil grade:

API service SG type or higher, JASO standard MA

Engine oil quantity:Without oil filter cartridge replacement:

3.80 L (4.02 US qt) (3.34 Imp.qt)With oil filter cartridge replacement:

4.00 L (4.23 US qt) (3.52 Imp.qt)Final gear oil:

Type:Shaft drive gear oil (Part No.: 9079E-SH001-00)

Quantity:0.20 L (0.21 US qt) (0.18 Imp.qt)

Cooling system:Coolant reservoir capacity (up to the maximum level mark):

0.25 L (0.26 US qt) (0.22 Imp.qt)Radiator capacity (including all routes):

2.60 L (2.75 US qt) (2.29 Imp.qt)Air filter:

Air filter element:Dry element

Fuel:Recommended fuel:

Unleaded gasoline onlyFuel tank capacity:

25.0 L (6.61 US gal) (5.50 Imp.gal)Fuel reserve amount:

5.5 L (1.45 US gal) (1.21 Imp.gal)

Fuel injection:Throttle body:

Manufacturer:MIKUNI

Type/quantity:42EHS/4

Spark plug (s):Manufacturer/model:

NGK/CR8EManufacturer/model:

DENSO/U24ESR-NSpark plug gap:

0.7–0.8 mm (0.028–0.031 in)Clutch:

Clutch type:Wet, multiple-disc

Transmission:Primary reduction system:

Spur gearPrimary reduction ratio:

75/48 (1.563)Secondary reduction system:

Shaft driveSecondary reduction ratio:

35/37 × 21/27 × 33/9 (2.698)Transmission type:

Constant mesh 5-speedOperation:

Left foot operationGear ratio:

1st:43/17 (2.529)

2nd:39/22 (1.773)


SPECIFICATIONS

8-2

8

3rd:31/23 (1.348)

4th:28/26 (1.077)

5th:26/28 (0.929)

Chassis:Frame type:

DiamondCaster angle:

26.00 °Trail:

109.0 mm (4.29 in)Front tire:

Type:Tubeless

Size:120/70 ZR17M/C (58W)

Manufacturer/model:METZELER/Roadtec Z6G

Manufacturer/model:BRIDGESTONE/BT021F F

Rear tire:Type:

TubelessSize:


METZELER/Roadtec Z6CManufacturer/model:

BRIDGESTONE/BT021R F

Loading:Maximum load:

211 kg (465 lb) (CAL)212 kg (467 lb) (U49)(Total weight of rider, passenger, cargo and accessories)

Tire air pressure (measured on cold tires):

Loading condition:0–90 kg (0–198 lb)Front:


290 kPa (42 psi) (2.90 kgf/cm²)Loading condition:

90–211 kg (198–465 lb) (CAL)90–212 kg (198–467 lb) (U49)Front:


290 kPa (42 psi) (2.90 kgf/cm²)High-speed riding:

Front:270 kPa (39 psi) (2.70 kgf/cm²)

Rear:290 kPa (42 psi) (2.90 kgf/cm²)

Front wheel:Wheel type:

Cast wheelRim size:

17M/C x MT3.50Rear wheel:

Wheel type:Cast wheel

Rim size:17M/C x MT5.50

Front brake:Type:

Dual disc brakeOperation:

Right hand operationRecommended fluid:

DOT 4Rear brake:

Type:Single disc brake

Operation:Right foot operation

Recommended fluid:DOT 4

Front suspension:Type:

Telescopic forkSpring/shock absorber type:

Coil spring/oil damperWheel travel:

135.0 mm (5.31 in)Rear suspension:

Type:Swingarm (link suspension)

Spring/shock absorber type:Coil spring/gas-oil damper

Wheel travel:125.0 mm (4.92 in)

Electrical system:Ignition system:

Transistorized coil ignition (digital)


SPECIFICATIONS

8-3

8

Charging system:AC magneto

Battery:Model:

GT14B-4Voltage, capacity:

12 V, 12.0 AhHeadlight:

Bulb type:Halogen bulb

Bulb voltage, wattage × quantity:Headlight:

12 V, 60 W/55.0 W × 2Tail/brake light:

12 V, 5.0 W/21.0 W × 2Front turn signal/position light:

12 V, 21 W/5.0 W × 2Rear turn signal light:

12 V, 21.0 W × 2License plate light:

12 V, 5.0 W × 1Meter lighting:

LEDNeutral indicator light:

LEDHigh beam indicator light:

LEDOil level warning light:

LEDTurn signal indicator light:

LEDEngine trouble warning light:

LED

ABS warning light:LED

Fuses:Main fuse:

50.0 AHeadlight fuse:

25.0 ASignaling system fuse:

15.0 AIgnition fuse:

10.0 ARadiator fan fuse:

15.0 A × 2Hazard fuse:

10.0 AFuel injection system fuse:

15.0 AABS control unit fuse:

10.0 AABS motor fuse:

30.0 AABS solenoid fuse:

20.0 AAuxiliary DC jack fuse:

3.0 ABackup fuse:

10.0 A


CONSUMER INFORMATION

9-1

9

EAU26351

Identification numbers Record the key identification number,vehicle identification number and mod-el label information in the spaces pro-vided below for assistance whenordering spare parts from a Yamahadealer or for reference in case the vehi-cle is stolen.KEY IDENTIFICATION NUMBER:

VEHICLE IDENTIFICATION NUMBER:

MODEL LABEL INFORMATION:

EAU26381

Key identification number

The key identification number isstamped into the key tag. Record thisnumber in the space provided and useit for reference when ordering a newkey.

EAU26400

Vehicle identification number

The vehicle identification number isstamped into the steering head pipe.Record this number in the space pro-vided.

NOTE:The vehicle identification number isused to identify your motorcycle andmay be used to register your motor-cycle with the licensing authority in yourarea.

1. Key identification number 1. Vehicle identification number



9-2

9

EAU26520

Model label

The model label is affixed to the frameunder the passenger seat. (See page3-15.) Record the information on this la-bel in the space provided. This informa-tion will be needed when orderingspare parts from a Yamaha dealer.

1. Model label



9-3

9

EAU26551

Reporting safety defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediatelyinform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation,U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a groupof vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problemsbetween you, your dealer, or Yamaha Motor Corporation, U.S.A.To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go tohttp://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can alsoobtain other information about motor vehicle safety from http://www.safercar.gov.



9-4

9

EAU26560

Motorcycle noise regulation TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person otherthan for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve-hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use ofthe vehicle after such device or element of design has been removed or rendered inoperative by any person.“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW”.These acts include tampering with the following systems; i.e., modification, removal, etc.

Exhaust system• Muffler• Exhaust pipe• Silencer

Intake system• Air cleaner case• Air cleaner element• Intake duct



9-5

9

EAU26632

Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document thatmaintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminderthat maintenance work is required. It is not acceptable proof of maintenance work.

Maintenanceinterval

Date ofservice Mileage Servicing dealer

name and address Remarks

600 mi(1000 km) or

1 month4000 mi

(7000 km) or6 months8000 mi







(49000 km) or48 months



9-6

9

36000 mi(55000 km) or

54 months40000 mi

(61000 km) or60 months

Maintenanceinterval

Date ofservice Mileage Servicing dealer

name and address Remarks



9-7

9

EAU26663

YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY

a)b)

c)d)e)f)

1.

2.

Yamaha Motor Corporation, U.S.A. hereby warrants that new Yamaha motorcycles will be free from defects in material and workmanship for the period of time stated herein, subject to certain stated limitations.

THE PERIOD OF WARRANTY for Yamaha motorcycles originally equipped with headlight, stoplight, and turn signals shall be one (1) year from the date of purchase, with no mileage limitation.

MODELS EXCLUDED FROM WARRANTY include those used for non-Yamaha-authorized renting, leasing or other commercial purposes, and TZ models.

DURING THE PERIOD OF WARRANTY, any authorized Yamaha motorcycle dealer will, free of charge, repair or replace any part adjudged defective by Yamaha due to faulty workmanship or material from the factory. Parts used in warranty repairs will be warranted for the balance of the product’s warranty period. All parts replaced under warranty become property of Yamaha Motor Corporation, U.S.A.

GENERAL EXCLUSIONS from this warranty shall include any failures caused by:

Competition or racing use.Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts.Abnormal strain, neglect, or abuse.Lack of proper maintenance.Accident or collision damage.Modification to original parts.

SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance.

THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to:

Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual, andGive notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business.

WARRANTY TRANSFER: To transfer the warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. An inspection and registration fee will be charged for this service.

EMISSION CONTROL SYSTEM WARRANTY:Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the period listed immediately below. Failures other than those resulting from defects in material or workmanship, which arise solely as a result of owner abuse and/or lack of proper maintenance, are not covered by this warranty.

Period6,000 km (3,750 miles)

or five years, whichever occurs first

12,000 km (7,465 miles)or five years whichever occurs first

18,000 km (11,185 miles)or five years, whichever occurs first

30,000 km (18,641 miles)or five years, whichever occurs first

YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGATIONS AND TIME LIMITS STATED IN THIS WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA MOTOR CORPORATION, U.S.A. AND EXCLUDED FROM THIS WARRANTY.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALSO EXCLUDED FROM THIS WARRANTY ARE ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING LOSS OF USE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

YAMAHA MOTOR CORPORATION, U.S.A.P.O. Box 6555

Cypress, California 90630

Engine Displacement Under 50cc

50cc to 169cc

170cc to 279cc

280cc and over



9-8

9

WARRANTY QUESTIONS AND ANSWERS

What costs are my responsibility during the warranty period?The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision damages, and oil, oil filters, air filters, spark plugs, and brake shoes.

What are some examples of “abnormal” strain, neglect, or abuse?These terms are general and overlap each other in areas. Specific examples include: Running the machine out of oil, sustained high rpm, full-throttle, operating the machine with a broken or damaged part which causes another part to fail, damage or failure due to improper or careless transportation and/or tie-down. If you have any specific questions on operation or maintenance, please contact your dealer for advice.

Does the warranty cover incidental costs such as towing or transportation due toa failure?No. The warranty is limited to repair of the machine itself.

May I perform any or all of the recommended maintenance shown in the Owner’s Manual instead of having the dealer do them?Yes, if you are a qualified mechanic and follow the procedures specified in the Owner’s and Service Manual. We do recommend, however, that items requiring special tools or equipment be done by a Yamaha motorcycle dealer.

Will the warranty be void or cancelled if I do not operate or maintain my new motorcycle exactly as specified in the Owner’s Manual?No. The warranty on a new motorcycle cannot be “voided” or “cancelled.” However, if a particular failure is caused by operation or maintenance other than as described in the Owner’s Manual, that failure may not be covered under warranty.

What responsibility does my dealer have under this warranty?Each Yamaha motorcycle dealer is expected to:

Completely set up every new machine before sale.Explain the operation, maintenance, and warranty requirements to your satisfaction at the time of sale, and upon your request at any later date.Each Yamaha motorcycle dealer is held responsible for his setup, service and warranty repair work.

Is the warranty transferable to second owners?Yes. The remainder of the existing warranty can be transferred upon request. The unit has to be inspected and re-registered by an authorized Yamaha motorcycle dealer for the policy to remain effective.

CUSTOMER SERVICE

If your machine requires warranty service, you must take it to any authorized Yamaha motorcycle dealer within the continental United States. Be sure to bring your warranty registration card or other valid proof of the original date of purchase. If a question or problem arises regarding the warranty, first contact the owner of the dealership. Since all warranty matters are handled at the dealer level, this person is in the best position to help you. IF you are still not satisfied and require additional assistance, please write to:

YAMAHA MOTOR CORPORATION, U.S.A.CUSTOMER RELATIONS DEPARTMENT

P.O. Box 6555Cypress, California 90630

When contacting Yamaha Motor Corporation, U.S.A., don’t forget to include any important information such as names, addresses, model, V.I.N. (frame number), dates, and receipts.

CHANGE OF ADDRESS

The federal government requires each manufacturer of a motor vehicle to maintain a complete, up-to-date list of all first purchasers against the possibility of a safety-related defect and recall. This list is compiled from the purchase registrations sent to Yamaha Motor Corporation, U.S.A. by the selling dealer at the time of your purchase.

If you should move after you have purchased your new motorcycle, please advise us of your new address by sending a postcard listing your motorcycle model name, V.I.N. (frame number), dealer number (or dealer’s name) as it is shown on your warranty card, your name and new mailing address. Mail to:

YAMAHA MOTOR CORPORATION, U.S.A.P.O. Box 6555

Cypress, California 90630Attention: Warranty Department

This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration record in accordance with federal law.

Q.A.

Q.A.

Q.

A.

Q.

A.

Q.

A.

Q.A.

1.2.

3.

Q.A.



9-9

9

EAU26750

YAMAHA EXTENDED SERVICE (Y.E.S.) Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.).

Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maximum owner satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.

Y.E.S. is flexible. You choose the plan that’s right foryou: 12 months, 24 months, 36 months or, on certain models, even 48 months beyond your warranty period.

Y.E.S. is designed and administered by the same Yamaha people who handle your warranty – and itshows in the comprehensive coverage benefits. There are no mileage limitations. Coverage isn’t limited to “moving parts” or the “drive train” like many other plans. And Y.E.S. covers manufacturing defects just like the warranty. See the sample contract at your Yamahadealer to see how comforting uninterrupted factory-backed protection can be.

You don’t have to pay anything for covered repairs. There’s no deductible to pay, and repairs aren’t“pro-rated.” You don’t have any “out-of-pocket” expenses for covered repairs.

In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost. TRIP gives you up to $150 reimbursement per occurrence for any reasonable expenses you incur because your Yamaha needs covered service: replacement vehicle rental, emergency towing, phone calls, even food and lodging when you are away from home. This superb coverage goes into effect when you purchase Y.E.S., so it applies to any warranty repairs as well as covered repairs during your entire Y.E.S. plan period.

Y.E.S. coverage is honored at any authorized Yamaha dealer nationwide.

Y.E.S. coverage is transferable to a new owner if yousell or trade-in. That can make your Yamaha much more valuable!

This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha Extended Service.



9-10

9

We urge you to act now. You’ll get the excellent benefits of TRIP coverage right away, and you’ll rest easy knowing you’ll have strong factory-backed protection even after your Yamaha Limited Warranty expires.

A special note:If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number (your frame number). We’ll be happy to help you get the Y.E.S. coverage you need.

Yamaha Service MarketingP.O. Box 6555Cypress, CA 906301-(866)-YES-EXTD (1-866-937-3983)


INDEXA

ABS....................................................... 3-12ABS warning light.................................... 3-2Accessories and replacement parts...... 6-24Accessory box....................................... 3-19Air filter element, cleaning..................... 6-18Auxiliary DC jack................................... 3-27

BBattery................................................... 6-32Brake and clutch fluid levels,

checking ............................................. 6-26Brake and clutch fluids, changing ......... 6-27Brake and clutch levers,

checking and lubricating ..................... 6-29Brake and shift pedals,

checking and lubricating ..................... 6-28Brake lever............................................ 3-11Brake pedal........................................... 3-11

CCables, checking and lubricating .......... 6-27Canister (for California only) ................. 6-12Care ........................................................ 7-1Catalytic converters .............................. 3-14Centerstand and sidestand,

checking and lubricating ..................... 6-29Clutch lever ..................................3-10, 6-24Coolant.................................................. 6-17Cowlings, opening and closing ............. 3-20

DDimmer switch ........................................ 3-9

EEngine break-in....................................... 5-4Engine idling speed, checking .............. 6-20Engine oil and oil filter cartridge............ 6-12

Engine stop switch.................................. 3-9Engine trouble warning light ................... 3-2

FFinal gear oil ......................................... 6-15Front and rear brake pads, checking.... 6-25Front fork, adjusting.............................. 3-21Front fork, checking .............................. 6-30Front turn signal light ............................ 6-36Fuel....................................................... 3-13Fuel tank cap ........................................ 3-13Fuses, replacing ................................... 6-33

HHandlebar position, adjusting ............... 3-20Handlebar switches ................................ 3-8Hazard switch ......................................... 3-9Headlight beams, adjusting .................. 3-19Headlight bulb, replacing ...................... 6-35High beam indicator light ........................ 3-2Horn switch............................................. 3-9

IIdentification numbers ............................ 9-1Ignition circuit cut-off system ................ 3-25Indicator and warning lights.................... 3-2

KKey identification number ....................... 9-1

LLabels, location of................................... 1-5License plate light bulb, replacing ........ 6-37

MMain switch/steering lock........................ 3-1Maintenance and lubrication, periodic .... 6-4Maintenance, emission control system... 6-3Maintenance, periodic ............................ 6-1Maintenance record................................ 9-5

Matte color, caution.................................7-1Model label..............................................9-2Multi-function display...............................3-4

NNeutral indicator light ..............................3-2Noise regulation ......................................9-4

OOil level warning light ..............................3-2

PPanels, removing and installing ..............6-8Parking ....................................................5-4Part locations ..........................................2-1Pre-operation check list...........................4-2

RRear brake light switch..........................6-25Rear suspension, lubricating.................6-30Rear view mirrors ..................................3-21Rider seat height, adjusting...................3-16

SSafety defects, reporting .........................9-3Safety information ...................................1-1Seats .....................................................3-15Shifting ....................................................5-2Shift pedal .............................................3-11Shock absorber assembly, adjusting ....3-23Sidestand ..............................................3-24Spark plugs, checking ...........................6-11Specifications ..........................................8-1Speedometer...........................................3-3Starting the engine ..................................5-1Start switch..............................................3-9Steering, checking.................................6-31Storage....................................................7-3Storage compartments..........................3-18


INDEXSwingarm pivots, lubricating................. 6-30

TTachometer ............................................ 3-3Throttle cable free play, checking......... 6-20Throttle grip and cable,

checking and lubricating..................... 6-28Tires...................................................... 6-21Tool kit .................................................... 6-1Troubleshooting.................................... 6-38Troubleshooting charts ......................... 6-39Turn signal indicator lights...................... 3-2Turn signal light or tail/brake light bulb,

replacing............................................. 6-36Turn signal switch................................... 3-9

VValve clearance .................................... 6-20Vehicle identification number.................. 9-1

WWarranty, extended ................................ 9-9Warranty, limited..................................... 9-7Wheel bearings, checking .................... 6-32Wheels.................................................. 6-23Windshield position adjusting switch ...... 3-9


A5-yoko_Blank.fm Page 1 Tuesday, April 8, 2003 11:43 AM

PRINTED IN JAPAN2007.10-1.4×1 CR

(E)

PRINTED ON RECYCLED PAPER YAMAHA MOTOR CO., LTD.

fjr fjr13ax(c) owner's manual - yamaha motor … · fjr13ax(c) owner’s manual...

Documents