finisher a1 installation

Download Finisher a1 Installation

Post on 02-Jun-2018

219 views

Category:

Documents

0 download

Embed Size (px)

TRANSCRIPT

  • 8/10/2019 Finisher a1 Installation

    1/13

    5

    5Installation(Inner Finisher-A1)

    Installation(Inner

    Finisher-A1)Making Pre-installtion

    Checks

    Checking Bundled

    ComponentsHow to Utilize ThisInstallation Procedure

    Installation Procedure

  • 8/10/2019 Finisher a1 Installation

    2/13

    5

    55-2

    5-2

    Installation(Inner Finisher-A1) > Kontrollen vor der Installation (German/Deutsch) > Vorsichtshinweise zur Installation

    Installation(Inner Finisher-A1) > Kontrollen vor der Installation (German/Deutsch) > Vorsichtshinweise zur Installation

    Making Pre-installation Checks

    Cautions at the Installation

    1. How to Disconnect the Main Power

    1) Turn OFF the main power switch of the Host Machine.

    2) Be sure that the Control Panel Display and the Main Power Lamp are both turned OFF,and then disconnect the power plug.

    MEMO:In case the USB Device Port-B1 is about to be installed in the host machine besidesthe Inner Finisher-A1, t the DP support plate and the cables contained in a carton boxof the USB Device Port-B1 prior to the installation of the Inner Finisher-A1.

    If the USB Device Port-B1 has already been installed in the host machine, tentativelyremove the device port body (except for the DP support plate and the cables) prior tothe service manual of the Inner Finisher-A1.

    F-5-1F-5-1

    Kontrollen vor der Installation (German/Deutsch)

    Vorsichtshinweise zur Installation

    1. Unterbrechen der Netzversorgung

    1) Schalten Sie den Netzschalter der Hostmaschine aus.

    2) berzeugen Sie sich zunchst, dass sowohl das Display auf dem Bedienfeld als auchdie Netzstrom-Kontrolleuchte erloschen sind, und ziehen Sie dann den Netzstecker.

    F-5-2F-5-2

  • 8/10/2019 Finisher a1 Installation

    3/13

  • 8/10/2019 Finisher a1 Installation

    4/13

    5

    55-4

    5-4

    Installation(Inner Finisher-A1) > How to Utilize This Installation Procedure > Symbols in the Illustration

    Installation(Inner Finisher-A1) > How to Utilize This Installation Procedure > Symbols in the Illustration

    How to Utilize This Installation Procedure

    When Using the Contained Parts(Bundled Components in the Shipping Carton)

    After unpacking, conrm the parts contained in the package by referring to the illustration of

    Bundled Components described in this procedure.

    The below symbol appears on the illustration in some steps when the parts contained in theshipping carton are to be used.

    Mind this symbol to be aware the parts contained in the shipping carton are to be used.

    Packaged Item

    Symbols in the Illustration

    The frequently-performed operations/works are described with symbols in this procedure.

    Check the description below.

    Connector

    Disconnect

    Screw

    Tighten Remove Connect Secure Free

    Harness

    PushInsert Plug in Turn on

    Sound CheckCheck Visual Check

    Claw

    Remove

    Checking instruction

  • 8/10/2019 Finisher a1 Installation

    5/13

    5

    55-5

    5-5

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    Installation Procedure

    Installation Procedure

    1) Hold the positions shown in the gure and take out the nisher fromthe carton. (Hold the positions specied by the instruction labels.)

    F-5-4F-5-4

    2) Remove the adhesive tapes and cushions and remove 3 screws to detach the 2 xtures.

    x3

    F-5-5F-5-5

    3) Remove the stopper and take out the 2nd delivery tray. (This step is applicable only when the 2nd delivery tray is installed in the host machine.) The 2nd delivery tray is no longer reused.

    F-5-6F-5-6

  • 8/10/2019 Finisher a1 Installation

    6/13

    5

    55-6

    5-6

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    4) Remove the reversal guide. The reversal guide is no longer reused.

    x2

    F-5-7F-5-7

    5) Open the toner cover and the right door of the host machine.

    F-5-8F-5-8 F-5-9F-5-9

    6) Remove 1 cap and 2 screws to detach the combined right front cover of the host machine and the inner cover. The right front cover is no longer reused.

    x2

    F-5-10F-5-10

    7) Remove 1 screw(TP) to detach the magnet catcher.

    x1

    F-5-11F-5-11

  • 8/10/2019 Finisher a1 Installation

    7/13

    5

    55-7

    5-7

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    8) Remove 2 screws to detach the front silver cover. (Left:TP screw, Right:RS-tight screw)

    x2

    F-5-12F-5-12

    9) Detach the combined delivery tray of the host machine and its lower cover. The lower cover is no longer reused.

    MEMO:It is good idea to place the paper in the host machine after removing the delivery tray to avoid screwsfalling in the host machine.

    F-5-13F-5-13

    10) Release the ttings to remove the left silver cover from tray lower cover.

    MEMO:Slide the cover to the front side to release the ttings, and then lift it up.

    F-5-14F-5-14

    11) Fit the left silver cover removed at Step 10 to the supplied tray

    lower cover.

    F-5-15F-5-15

  • 8/10/2019 Finisher a1 Installation

    8/135

    55-8

    5-8

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    12) Release the tting to remove the switch cover from the right front cover.

    F-5-16F-5-16

    13) Fit the switch cover removed at Step 12 to the Right front cover.

    F-5-17F-5-17

    14) Remove 1 cap and 1 screw to detach the inner cover (small) of the host machine. The inner cover (small) is no longer reused.

    x1

    F-5-18F-5-18

    15) Remove the sensor ag of the 1st delivery tray. The sensor ag is no longer reused.

    MEMO: Bend the sensor ag shaft a little to remove it.

    1

    2

    3

    F-5-19F-5-19

  • 8/10/2019 Finisher a1 Installation

    9/135

    55-9

    5-9

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    16) Remove the sensor ag of the 2nd delivery tray. The sensor ag is no longer reused. (This step is applicable only when the 2nd delivery tray is installed in the host machine.)

    MEMO: Bend the sensor ag shaft a little to remove it.

    1

    2

    F-5-20F-5-20

    17) Remove 1 screw to detach the small cover. Reverse the small cover and restore it to the original position. Removedscrew is no longer reused for the installation.(This step is applicable only when the 2nd delivery tray is installed in the host machine.)

    MEMO:The removed screw is no longer reused.

    F-5-21F-5-21

    18) Remove 2 screws to detach the control panel lower cover. The lower cover is no longer reused.

    x2

    F-5-22F-5-22

    19) Remove 1 screw and detach the protection cover at delivery part by shifting it to the front side. Remove the paper placed at the step 9).

    The protection cover is no longer reused.

    x1

    F-5-23F-5-23

    5

  • 8/10/2019 Finisher a1 Installation

    10/135

    55-10

    5-10

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    20) Slide the tray lower cover to rear side until it stops while pressing it down and x it by 1screw (binding screw, M3x6) using a stubby screwdriver.

    x1

    F-5-24F-5-24

    21) Fix the supplied harness cover and nisher guide with 1 screw (binding screw, M3x12)using a stubby screwdriver.

    x1

    F-5-25F-5-25

    22) Fix the supplied wire saddle to the upper side of the fan.

    F-5-26F-5-26

    5

  • 8/10/2019 Finisher a1 Installation

    11/135

    55-11

    5-11

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    23) Hold the positions shown in the gure and lift the nisher, and then set the nisher into the host machine.

    *CAUTION:

    When setting the nisher in the host machine, be careful so that the right lower plate does not touch the hook of the silver cover.

    F-5-27F-5-27

    24) Fit the xture with 1 screw (RS-tight screw, M3x6).

    x1

    F-5-28F-5-28

    25) Fix the right side of the nisher to the host machine with 1 screw (RS-tight screw, M3x6).

    x1

    F-5-29F-5-29

  • 8/10/2019 Finisher a1 Installation

    12/13

    5

  • 8/10/2019 Finisher a1 Installation

    13/135

    55-13

    5-13

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    Installation(Inner Finisher-A1) > Installation Procedure > Installation Procedure

    30) Fix the combined right front cover and inner cover contained in the nishercarton box with 2 screws (RS-tight screw, M3x6).

    x2

    F-5-34F-5-34

    31) Set the supplied staple cartridge into the stapler.

    F-5-35F-5-35

    32) Close all the external covers.

    Stick the supplied main power label on the upper part of themain power switch.

    F-5-36F-