fingerprint recognition safe...fingerprint profiles” opening the safe 1. press the ‘a’ button....

CAUTION: Do not keep the override keys inside the safe.

FINGERPRINT RECOGNITION SAFEMODEL NO: CS400FP

PART NO: 7710200

OPERATION & MAINTENANCEINSTRUCTIONS

LS1014

P

INTRODUCTIONThank you for purchasing this CLARKE Fingerprint Recognition Safe.

Before attempting to operate the safe, it is essential that you read this manual thoroughly and carefully follow all instructions given. In doing so you can look forward to the safe giving you long and satisfactory service.

GUARANTEEThis CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

SPECIFICATION

REPLACEMENT OVERRIDE KEY A small label is located on the front of each safe with a key number. The number will start with either the letter "J" or "G" followed by several digits. This number must be registered with us in the event you require a replacement key.

Please complete the registration form supplied and send it to the address stated with the form. If you fail to register the safe we will not be able to provide you with a replacement key.

We recommend that in addition to sending the completed form you remove the label from the safe and fix it to the space below. Please retain this document for future reference.

Fix or record the key number here

Dimensions (D x W x H) 272 x 350 x 250 mm

Weight 11 kg

Batteries 4 x AA (1.5V)

Volume 16.3 L

Number of keys supplied 2

2arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

P

BEFORE USE

OPENING THE SAFE FOR THE FIRST TIME1. Rotate the plate downwards as

shown,

2. Use the key supplied to open your safe.

• The notch on the key should be at the top

INSTALLING THE SAFEThe safe should be secured vertically to a wall or to the floor using the expansion bolts (supplied).

• There are holes on the rear and bottom of the safe for securing to a wall or the floor.

INSTALLING THE BATTERIESThe safe requires 4 x AA (1.5V) batteries.

1. Open the safe.

2. Remove the battery cover plate on the back of the door and install the batteries.

• Ensure the batteries are fitted with the correct polarity.

• Use of alkaline batteries is recommended.

3. Replace the battery cover plate.


P

USING THE SAFEThe safe can be opened by any finger until a profile is added See “Programming The Fingerprint Profiles”

OPENING THE SAFE1. Press the ‘A’ button.

• The fingerprint reader will light up with a red light.

2. Place your finger on fingerprint reader within 5 seconds.

• When panel displays “OK”, The safe will open.

CLOSING THE SAFE1. Close the safe door and press the ‘A’

Button.


P

PROGRAMMING THE FINGERPRINT PROFILES

NOTE: The safe can record 100 different fingerprints.

1. With the door open, and the locking bars retracted, press the green button on the top of the door.

• The fingerprint reader will light up with a red light.

2. Place your finger on the fingerprint reader within 5 seconds.

• When panel displays “OK” the profile has been set.

3. Repeat steps 1+ 2 for each additional profile you want to create.

IMPORTANT:• To enhance the fingerprint

identification rate, we recommend the same finger is programmed 3 times.

• We also suggest two fingers from each hand are programmed.

• Clean fingers before placing on the reader.

• Keep the reader clean and free from grease and moisture.

• Always keep finger steady and fully touch the fingerprint reader when recording or reading fingerprints.

• The little finger is not recommended for fingerprint identification.

• Avoid strong light on the top of fingerprint reader.

DELETING ALL PROFILESPress the red button 3 times.

When the panel shows “OK”, all the fingerprint records have been deleted successfully.

Now the system is returned to its original state and any finger can open the safe.


P

CARE AND MAINTENANCE

• Keep the safe between 0°C to 50°C ambient temperatures. Avoid using in damp conditions.

OVERRIDE INSTRUCTION TO OPEN THE SAFEWe have engineered a manual override system for your safe. If there is any emergency, move the plate as shown, Use the key to open your safe.

• CAUTION: Do not keep the keys in the safe.


P

DECLARATION OF CONFORMITY


fingerprint recognition safe...fingerprint profiles” opening the safe 1. press the ‘a’ button....

Documents