filled core. moisture barrier. - centelsa · filled core. moisture barrier. foamed-skin...
TRANSCRIPT
77
Description
Soft copper wires insulated with high density polyethylene, foam skin or solid.Filled core, conformed by groups of pairs or by unit of groups of pairs. Aluminumshield and external jacket in polyethylene type moisture barrier.
Construction
ConductorSoft copper wires
InsulationFoam skin or solid high density polyethylene.
Twisted PairsInsulated conductors are twisted into pairs
Core AssemblyUp to 70 pairs, groups of 10 pairs, from 100 to 300 pairs groups of 25 pairs,from 400 pairs and more, units of 100 pairs (each unit is conformed by 4 groupsof 25 pairs)
Spare pairsOne spare pair white-red colored at the interstices of each 100 pairs unit, toguarantee nominal numbers of pairs.
IdentificationPairs, groups and units that conform the core, are identified by color code(Attached)
Core WrapNon-hygroscopic dielectric tape. Offers dielectric strength between core andsheath
ShieldCorrugated Aluminum tape both sides covered with copolymer
JacketBlack polyethylene, abrasion, weather, and penetration to water resistant
Outside Telephone CableFilled Core. Moisture Barrier.
8
Moisture BarrierFilled Core with elastomeric compound, aluminum tape both sidescovered with copolymer and polyethylene external jacket, firmly bondedto external side of aluminum tape
OptionsManufacturing according to REA and/or Bellcore specificationsShield in Flat Aluminum tape. Armor in corrugated and copolymercovered Steel tape for direct buried and for rodent protection. Galvanizedsteel wires armor for vertical installations. Other Core Assemblies areavailable upon request.
ApplicationsTrunk cable and distribution cable networks. Special for wet locations;the elastomeric compound filler prevents the entrance of moisture tothe core. Installation in ducts or raceways; for buried direct in locationswithout heavy traffic.
CENTELSA Outside Telephone Cable, are able for voice and datatransmission up to 6.3 MHz, optimizing the bandwidth of copper cables.
Standards and Specifications
CENTELSA Outside Telephone Cable, are manufactured under thefollowing standards:
ANSI/ICEA S-84-608 Telecommunications cable filled, polyolefininsulated copper conductor.
ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefininsulated copper conductor.
NTC-2061 Telecommunications copper conductor multipair cables,polyolefin insulated and covered, filled and dry.
Certifications
CENTELSA Outside Telephone Cable, are certified by:ICONTEC (Colombia). Norma NTC 2061.
Note: Other configurations, sizes, colors and length not specifiedherein are available upon request.
9Note: 1. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
NOMINALPAIRS
STANDARDLENGTHBY REEL
(m)
INSULATIONTHICKNESS
(mm)
APPROX.TOTAL
WEIGTH(kg/km)
OVERALLDIAMETER
(mm)
SPAREPAIRS
CONDUCTORDIAMETER
(mm)
JACKETTHICKNESS
(mm)
94141187231275356479692886
127016682044241935654699583769419126
120188252316378498682996
12831876244630373606531270188684
1038613682
158257350442531724994
1452188027323605447553097848
10374128461537120280
0.180.180.180.180.180.180.180.180.180.180.180.180.180.180.180.180.180.180.200.200.200.200.200.200.200.200.200.200.200.200.200.200.200.200.200.200.260.260.260.260.260.260.260.260.260.260.260.260.260.260.260.260.260.26
0.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.60
1.401.401.401.401.401.401.401.601.601.601.801.801.802.002.202.402.402.401.401.401.401.401.401.401.401.601.601.801.802.002.002.202.402.402.602.601.401.401.401.401.401.601.601.801.801.802.002.202.202.402.602.602.802.80
9.7511.5612.9614.1315.1716.9619.3022.8725.4829.9134.0637.3540.3248.4855.3261.4366.7375.8810.6712.8614.5515.9717.2319.4022.2226.4629.6235.4039.9244.3947.9957.6466.0372.9279.5790.6312.0814.8617.0018.8020.3823.5527.1332.3836.3943.2549.3854.8059.3571.6781.9990.7299.02
113.03
150015001500150015001500100010001000
750500500500350300250250250
150015001500150015001500100010001000
750500500500350300250250250
150015001500150015001500100010001000
750500500500350300250250250
102030405070
100150200300400500600900
1200150018002400
102030405070
100150200300400500600900
1200150018002400
102030405070
100150200300400500600900
1200150018002400
------12234569
12151824
------12234569
12151824
------12234569
12151824
Outside Telephone Cable.Filled Core. Moisture Barrier.Foamed-Skin polyethylene insulation.
Standards: ANSI/ICEA S-84-608 Telecommunications cable filled, polyolefininsulated copper conductor.NTC-2061 Telecommunications copper conductor multipair cables, polyolefininsulated and covered, filled and dry.
10
Outside Telephone Cable.Filled Core. Moisture Barrier.Solid polyethylene insulation.
Standards: ANSI/ICEA S-84-608 Telecommunications cable filled, polyolefininsulated copper conductor.NTC-2061 Telecommunications copper conductor multipair cables, polyolefininsulated and covered, filled and dry.
Note: 1. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
106160211262311405548792
101514761913237728124128544067148026
10547142224306384459620850
12321590230030333762445465618663
107131281316877
177294407514624849
11681710221532624292532463209325
12270152601818324082
0.230.230.230.230.230.230.230.230.230.230.230.230.230.230.230.230.230.230.300.300.300.300.300.300.300.300.300.300.300.300.300.300.300.300.300.300.350.350.350.350.350.350.350.350.350.350.350.350.350.350.350.350.350.35
0.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.60
1.401.401.401.401.401.401.401.601.601.801.802.002.002.202.402.402.602.601.401.401.401.401.401.601.601.801.801.802.002.202.202.402.602.602.802.801.401.401.401.401.401.601.601.801.802.002.202.402.402.602.602.802.803.00
10.3412.4013.9815.3216.4918.5321.1825.1828.1533.5937.8342.0545.4354.5162.2668.8875.1385.5211.8314.5116.5718.3019.8322.9026.3431.4235.2741.8847.8153.0457.4269.3179.2687.6795.68
109.1813.1316.3518.8220.9022.7426.3330.4736.4941.1149.4556.4462.8368.1082.1193.57
104.08113.20129.82
150015001500150015001500100010001000
750500500500350300250250250
150015001500150015001500100010001000
750500500500350300250250250
150015001500150015001500100010001000
750500500500350300250250250
102030405070
100150200300400500600900
1200150018002400
102030405070
100150200300400500600900
1200150018002400
102030405070
100150200300400500600900
1200150018002400
------12234569
12151824
------12234569
12151824
------12234569
12151824
NOMINALPAIRS
STANDARDLENGTHBY REEL
(m)
INSULATIONTHICKNESS
(mm)
APPROX.TOTAL
WEIGTH(kg/km)
OVERALLDIAMETER
(mm)
SPAREPAIRS
CONDUCTORDIAMETER
(mm)
JACKETTHICKNESS
(mm)
11
Outside Telephone Cable
Description
Soft copper wires insulated with high density polyethylene, foam skin or solid.Core conformed by groups of pairs or by unit of groups of pairs. Filled coreAluminum shield and double Jacket (inner and outer) in polyethylene typemoisture barrier.
Construction
ConductorSoft copper wires
InsulationFoam skin or solid high density polyethylene.
Twisted PairsInsulated conductors are twisted into pairs
Core AssemblyUp to 70 pairs, groups of 10 pairs, from 100 to 300 pairs groups of 25 pairs,from 400 pairs and more, units of 100 pairs (each unit is conformed by 4 groupsof 25 pairs)
Spare pairsOne spare pair white-red colored at the interstices of each 100 pairs unit, toguarantee nominal numbers of pairs.
IdentificationPairs, groups and units that conform the core, are identified by color code(Attached)
Inner JacketBlack polyethylene, abrasion, weather, and penetration to water resistant
Filled Core. Double Jacket. Moisture Barrier.
12
Core WrapNon-hygroscopic dielectric tape. Offers dielectric strength betweencore and sheath
ShieldCorrugated Aluminum tape both sides covered with copolymer
Outer JacketBlack polyethylene, abrasion, weather, and penetration to waterresistant
Moisture BarrierFilled Core with elastomeric compound, inner polyethylene jacket,aluminum tape both sides covered with copolymer and outerpolyethylene external jacket, firmly bonded to external side of aluminumtape.
Options
Manufacturing according to REA and/or Bellcore specificationsShield in Flat Aluminum tape. Armor in corrugated and copolymercovered Steel tape for direct buried and for rodent protection. Galvanizedsteel wires armor for vertical installations. Other Core Assemblies areavailable upon request.
Applications
Trunk cable and distribution cable networks. Special for wet locations;the elastomeric compound filler prevents the entrance of moisture tothe core.
Trunk cable and distribution cable networks. Special for wet locations;the elastomeric compound filler prevents the entrance of moisture tothe core.
The inner jacket offers additional blocking to the entrance of humidityto the core, increases the dielectric strength pair-shield and improvescable resistance to penetration of sharp objects.
CENTELSA Outside Telephone Cable, are able for voice and datatransmission up to 6.3 MHz, optimizing the bandwidth of copper cables.
13
Standards and Specifications
CENTELSA Outside Telephone Cable, are manufactured under the followingstandards:
Standards:ANSI/ICEA S-84-608 Telecommunications cable filled, polyolefin insulatedcopper conductor.NTC-2061 Telecommunications copper conductor multipair cables, polyolefininsulated and covered, filled and dry.
Certifications
CENTELSA Outside Telephone Cable, are certified by:ICONTEC (Colombia). Standard NTC 2061.
Note: Other configurations, sizes, colors and length not specified herein areavailable upon request.
14
Outside Telephone Cable.Filled Core. Moisture Barrier.Foamed-Skin polyethylene insulation.
Standards: ANSI/ICEA S-84-608 Telecommunications cable filled, polyolefininsulated copper conductor.NTC-2061 Telecommunications copper conductor multipair cables, polyolefininsulated and covered, filled and dry.
Note: 1. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
116166215261307392519746947
134117592144252637124882605771739390
143216283350415539729
105913541971255231783751550272548938
1068614031
183285386481574780
10591539197728503754465655048104
10690131961577520748
0.180.180.180.180.180.180.180.180.180.180.180.180.180.180.180.180.180.180.200.200.200.200.200.200.200.200.200.200.200.200.200.200.200.200.200.200.260.260.260.260.260.260.260.260.260.260.260.260.260.260.260.260.260.26
0.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.60
1.401.401.401.401.401.401.401.601.601.601.801.801.802.002.202.402.402.401.401.401.401.401.401.401.401.601.601.801.802.002.002.202.402.402.602.601.401.401.401.401.401.601.601.801.801.802.002.202.202.402.602.602.802.80
11.1512.9614.3615.5316.5718.3620.7024.4727.0831.5135.8639.1542.1250.4857.5263.8369.1378.2812.0714.2615.9517.3718.6320.8023.6228.0631.2237.2041.7246.3949.9959.8468.4375.3282.1793.2313.4816.2618.4020.2021.7825.1528.7334.1838.1945.0551.3857.0061.5574.0784.5993.32
101.82115.83
150015001500150015001500100010001000
750500500500350300250250250
150015001500150015001500100010001000
750500500500350300250250250
150015001500150015001500100010001000
750500500500350300250250250
102030405070
100150200300400500600900
1200150018002400
102030405070
100150200300400500600900
1200150018002400
102030405070
100150200300400500600900
1200150018002400
------12234569
12151824
------12234569
12151824
------12234569
12151824
0.700.700.700.700.700.700.700.800.800.800.900.900.901.001.101.201.201.200.700.700.700.700.700.700.700.800.800.900.901.001.001.101.201.201.301.300.700.700.700.700.700.800.800.900.900.901.001.101.101.201.301.301.401.40
NOMINALPAIRS
STANDARDLENGTHBY REEL
(m)
INSULATIONTHICKNESS
(mm)
APPROX.TOTAL
WEIGTH(kg/km)
OVERALLDIAMETER
(mm)
SPAREPAIRS
CONDUCTORDIAMETER
(mm)
JACKETTHICKNESS
(mm)
TOTALWEIGTH(kg/km)
15
Outside Telephone Cable
Description
Soft copper wires insulated with high density polyethylene, foam skin or solid. Aircore, conformed by groups of pairs or by unit of groups of pairs. Aluminum shield andexternal jacket in polyethylene type moisture barrier.
Construction
ConductorSoft copper wires
InsulationFoam skin or solid high density polyethylene.
Twisted PairsInsulated conductors are twisted into pairs
Core AssemblyUp to 70 pairs, groups of 10 pairs, from 100 to 300 pairs groups of 25 pairs, from 400pairs and more, units of 100 pairs (each unit is conformed by 4 groups of 25 pairs)
Spare pairsOne spare pair white-red colored at the interstices of each 100 pairs unit, to guaranteenominal numbers of pairs.
IdentificationPairs, groups and units that conform the core, are identified by color code (Attached)
Core WrapNon-hygroscopic dielectric tape. Offers dielectric strength between core and sheath
ShieldCorrugated Aluminum tape both sides covered with copolymer
JacketBlack polyethylene, abrasion, weather, and penetration to water resistant
Air Core. Moisture Barrier.
16
Moisture BarrierFilled Core with elastomeric compound, aluminum tape both sides coveredwith copolymer and polyethylene external jacket, firmly bonded to externalside of aluminum tape
Options
Manufacturing according to REA and/or Bellcore specificationsShield in Flat Aluminum tape. Armor in corrugated and copolymer coveredSteel tape for direct buried and for rodent protection. Galvanized steel wiresarmor for vertical installations. Other Core Assemblies are available uponrequest.
Applications
Trunk cable and distribution cable networks. For use in pressurized networks.Installation in ducts or raceways
CENTELSA Outside Telephone Cable, are able for voice and data transmissionup to 6.3 MHz, optimizing the bandwidth of copper cables.
Standards and SpecificationsCENTELSA Outside Telephone Cable, are manufactured under the followingstandards:
ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin insulatedcopper conductor.NTC-2061 Telecommunications copper conductor multipair cables, polyolefininsulated and covered, filled and dry.
Certifications
CENTELSA Outside Telephone Cable, are certified by:ICONTEC (Colombia). Standard NTC 2061.
Note: Other configurations, sizes, colors and length not specified hereinare available upon request.
17
Note: 1. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
86125163200232300404579734
104713531678197729083800471655957438
108164217270318419566823
105415411998247829414323566270408372
11070133214288361433587801
11471478216528293515416461398113
100871200415884
0.150.150.150.150.150.150.150.150.150.150.150.150.150.150.150.150.150.150.170.170.170.170.170.170.170.170.170.170.170.170.170.170.170.170.170.170.210.210.210.210.210.210.210.210.210.210.210.210.210.210.210.210.210.21
0.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.60
1.401.401.401.401.401.401.401.601.601.601.601.801.802.002.002.202.202.601.401.401.401.401.401.401.401.601.601.801.802.002.002.202.202.402.402.601.401.401.401.401.401.601.601.601.601.801.802.002.002.202.402.602.602.80
9.4111.0912.3813.4614.4216.0818.2421.5723.9828.0831.5334.9837.7345.3151.2856.9261.6871.1010.2612.2813.8415.1516.3018.3120.9124.8627.7733.1337.3041.3944.7853.7160.9367.8573.6084.2211.4714.0015.9417.5819.0221.9425.1929.5933.2339.8245.0950.0954.2365.4474.8683.2190.39
103.54
150015001500150015001500100010001000
750500500500350300250250250
150015001500150015001500100010001000
750500500500350300250250250
150015001500150015001500100010001000
750500500500350300250250250
102030405070
100150200300400500600900
1200150018002400
102030405070
100150200300400500600900
1200150018002400
102030405070
100150200300400500600900
1200150018002400
------12234569
12151824
------12234569
12151824
------12234569
12151824
NOMINALPAIRS
STANDARDLENGTHBY REEL
(m)
INSULATIONTHICKNESS
(mm)
APPROX.TOTAL
WEIGTH(kg/km)
OVERALLDIAMETER
(mm)
SPAREPAIRS
CONDUCTORDIAMETER
(mm)
JACKETTHICKNESS
(mm)
Outside Telephone Cable.Air Core. Moisture Barrier.Foamed-Skin polyethylene insulation.
Standards: ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin insulated copper conductor.NTC-2061 Telecommunications copper conductor multipair cables, polyolefin insulated and covered, filled anddry.
18
Note: 1. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
Outside Telephone Cable.Air Core. Moisture Barrier.Solid polyethylene insulation.
Standards: ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin insulated copper conductor.NTC-2061 Telecommunications copper conductor multipair cables, polyolefin insulated and covered, filled anddry.
107160208254298385515738938
133417522138252036944858602471429417
137213284352418548742
107513782009260532283818560273839106
1088214297
172276374468560758
10341501193327873670454553807914
10442128951541420283
0.150.150.150.150.150.150.150.150.150.150.150.150.150.150.150.150.150.150.190.190.190.190.190.190.190.190.190.190.190.190.190.190.190.190.190.190.220.220.220.220.220.220.220.220.220.220.220.220.220.220.220.220.220.22
0.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.400.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.500.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.600.60
1.401.401.401.401.401.401.401.601.601.601.801.801.802.002.202.402.402.601.401.401.401.401.401.401.401.601.601.801.802.002.002.202.402.402.602.601.401.401.401.401.401.601.601.801.801.802.002.202.202.402.602.602.802.80
11.1513.5515.3916.9418.3020.6723.7528.3431.7937.6343.0547.3951.3262.0170.9278.8585.6598.1312.6615.6817.9919.9521.6724.6628.5434.2138.5646.4252.6358.5163.6176.7487.9197.39
106.37121.58
14.2117.8720.6823.0525.1429.1833.8940.6846.0254.9663.0670.0776.0791.95
105.41116.91127.71146.16
150015001500150015001500100010001000
750500500500350300250250250
150015001500150015001500100010001000
750500500500350300250250250
150015001500150015001500100010001000
750500500500350300250250250
102030405070
100150200300400500600900
1200150018002400
102030405070
100150200300400500600900
1200150018002400
102030405070
100150200300400500600900
1200150018002400
------12234569
12151824
------12234569
12151824
------12234569
12151824
NOMINALPAIRS
STANDARDLENGTHBY REEL
(m)
INSULATIONTHICKNESS
(mm)
APPROX.TOTAL
WEIGTH(kg/km)
OVERALLDIAMETER
(mm)
SPAREPAIRS
CONDUCTORDIAMETER
(mm)
JACKETTHICKNESS
(mm)
19
Description
Soft copper wires insulated with high density polyethylene, foam skin or solid. Aircore, conformed by groups of pairs or by unit of groups of pairs. Aluminum shield,support messenger and external jacket in polyethylene type moisture barrier.
Construction
ConductorSoft copper wires
InsulationFoam skin or solid high density polyethylene.
Twisted PairsInsulated conductors are twisted into pairs
Core AssemblyUp to 70 pairs, groups of 10 pairs, from 100 to 300 pairs groups of 25 pairs, from 400pairs and more, units of 100 pairs (each unit is conformed by 4 groups of 25 pairs)
Spare pairsOne spare pair white-red colored at the interstices of each 100 pairs unit, to guaranteenominal numbers of pairs.
IdentificationPairs, groups and units that conform the core, are identified by color code (Attached)
Core WrapNon-hygroscopic dielectric tape. Offers dielectric strength between core and sheath
ShieldCorrugated Aluminum tape both sides covered with copolymer
Support Messenger7 Strand high strength galvanized steel wire.
JacketBlack polyethylene, abrasion, weather, and penetration to water resistant
Outside Telephone CableSelf-supportedFigure 8. Air Core. Moisture Barrier.
20
Moisture BarrierAir Core (for pressurerd systems) with elastomeric compound, aluminumflat tape both sides covered with copolymer and polyethylene external jacket,firmly bonded to external side of aluminum tape
Options
Manufacturing according to REA and/or Bellcore specificationsShield in corrugated Aluminum tape. Filled Core. Galvanized steel wiresfully flooded for corrosion protection. Other Core Assemblies are availableupon request.
Applications
For pressured systems overhead trunk cable and distribution cable networks.Aerial installation suspended from Messenger
CENTELSA Outside Telephone Cable, are able for voice and data transmissionup to 6.3 MHz, optimizing the bandwidth of copper cables.
Standards and Specifications
CENTELSA Outside Telephone Cable Figure 8, are manufactured under thefollowing standards:
ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin insulatedcopper conductor.NTC-2061 Telecommunications copper conductor multipair cables, polyolefininsulated and covered, filled and dry.
Certifications
CENTELSA Outside Telephone Cable, are certified by:ICONTEC (Colombia). Standard NTC 2061.
Note: Other configurations, sizes, colors and length not specified hereinare available upon request.
21
Note: 1. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
Outside Telephone Cable.Figure 8. Air Core. Self Supported. Moisture Barrier.Foamed-Skin polyethylene insulation.
Standards: ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin insulated copper conductor.NTC-2061 Telecommunications copper conductor multipair cables, polyolefin insulated and covered, filled anddry.
221261298334368435536789946
1256242298352403453552780
103312661728
0.150.150.150.150.150.150.150.150.150.150.170.170.170.170.170.170.170.170.170.17
0.400.400.400.400.400.400.400.400.400.400.500.500.500.500.500.500.500.500.500.50
1.401.401.401.401.401.401.401.601.601.601.401.401.401.401.401.401.401.601.601.60
8.03 x 18.67 9.71 x 20.3511.00 x 21.6412.08 x 22.7213.04 x 23.6814.70 x 25.3416.86 x 27.5020.19 x 32.1522.61 x 34.5726.70 x 38.66 8.88 x 19.5210.90 x 21.5412.46 x 23.1013.77 x 24.4114.93 x 25.5716.93 x 27.5719.54 x 31.5023.48 x 35.4426.39 x 38.3531.34 x 43.30
150015001500150015001500100010001000
750150015001500150015001500100010001000
750
10 20 30 40 50 70100150200300 10 20 30 40 5070
100150200300
------1223------1223
1.571.571.571.571.571.571.572.032.032.031.571.571.571.571.571.572.032.032.032.03
77777777777777777777
NOMINALPAIRS
STANDARDLENGTHBY REEL
(m)
INSULATIONTHICKNESS
(mm)
APPROX.TOTAL
WEIGTH(kg/km)
EXTERNALDIMENSIONS
(mm)
SPAREPAIRS
CONDUCTORDIAMETER
(mm)
JACKETTHICKNESS
(mm)
MESSENGER
STRANDSNo.
DIAMETER(mm)
22
Note: 1. Data herein indicated are approximated and are subject to normal manuracturing tolerances.
Outside Telephone Cable.Figure 8. Air Core. Self Supported. Moisture Barrier.Solid polyethylene insulation.
Standards: ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin insulated copper conductor.NTC-2061 Telecommunications copper conductor multipair cables, polyolefin insulated and covered, filled anddry.
222263300336371439543799959
1277246305361414467570805
107113151800
0.150.150.150.150.150.150.150.150.150.150.190.190.190.190.190.190.190.190.190.19
0.400.400.400.400.400.400.400.400.400.400.500.500.500.500.500.500.500.500.500.50
1.401.401.401.401.401.401.401.601.601.601.401.401.401.401.401.401.401.601.601.60
8.03 x 18.67 9.71 x 20.3511.00 x 21.6412.08 x 22.7213.04 x 23.6814.70 x 25.3416.86 x 27.5020.19 x 32.1522.61 x 34.5726.70 x 38.66 9.10 x 19.7411.22 x 21.8612.85 x 23.4914.22 x 24.8615.43 x 26.0717.52 x 28.1620.25 x 32.2124.35 x 36.3127.40 x 39.3632.57 x 44.53
150015001500150015001500100010001000
750150015001500150015001500100010001000
750
102030405070
100150200300
102030405070
100150200300
------1223------1223
1.571.571.571.571.571.571.572.032.032.031.571.571.571.571.571.572.032.032.032.03
77777777777777777777
NOMINALPAIRS
STANDARDLENGTHBY REEL
(m)
INSULATIONTHICKNESS
(mm)
APPROX.TOTAL
WEIGTH(kg/km)
EXTERNALDIMENSIONS
(mm)
SPAREPAIRS
CONDUCTORDIAMETER
(mm)
JACKETTHICKNESS
(mm)
MESSENGER
STRANDSNo.
DIAMETER(mm)
23
Description
Drop Wire Paralleled. Hard copper conductors or steel copper covered,polyethylene or PVC insulated.
Construction
ConductorHard copper or steel copper covered (CCS)
InsulationSingle layer Polyethylene for DWP-PE and insulation – jacket integral for DWP-2PE, weather resistant.Polyethylene Insulation and PVC jacket for DWP PE-PVC.Flame retardant PVC for DWP-PVC.Paralleled conductors with polarization ridge and conductor separator membrane.
Application
Self supporting one pair parallel conductor Drop Wire intended for aerial serviceconnection to the subscriber
Standards
CENTELSA telephone wires DWP are manufactured under the followingstandards:NTC 1300 Service Drop telephone wire, inside installations and jumper.
Certifications
CENTELSA Outside Telephone Wire, are certified by:CIDET (Colombia). Standard NTC 1300.
Package100 or 200 meters spools in corrugated carton boxes
Note: other configurations and sizes not specified in this catalogue are availableupon request.
Outside TelephoneWire DWPDrop Wire Paralell
24
Outside Telephone Wire (International System Unit)Drop Wire Parallel
Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.
Outside Telephone Wire (International System Unit)Drop Wire Parallel
Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.
0.800.80
0.80
0.800.801.50
MATERIALAISLAMIENTO
Notes: 1. DC resistance calculated based on a 10.785 ohm-cmil/ft resistivity for Hard cooper and 33.91 ohm-cmil/ft for steel copper covered.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
Hard CopperHard Copper
CopperClad Steel
CopperClad Steel
Hard CopperHard CopperHard CopperHard CopperHard Copper
2 x 18
DWP PVC
APPROX.TOTAL
WEIGTH(kg/km)
INSULATIONMATERIAL
EXTERNALDIMENSIONS
(mm)
DCRESISTANCE
AT 20° C1
(ohm/km)
INSULATIONRESISTANCE
(Mohm-km)TYPE CONDUCTOR
CROSSSECTION
(mm2)
INSULATIONTHICKNESS
(mm)
ONECONDUCTOR
TENSILE STRENGTH(Nominal)
(MPa)
JACKETTHICKNESS
(mm)SIZE
No. x AWG
SEPARATOR(mm)
STRANDDIAMETER
(mm)
DWP PE CCS
DWP PVC CCS
2 x 182 x 20
2 x 18
2 x 182 x 20
DWP PE
2 x 182 x 182 x 20
DWP 2PE
DWP PE-PVC
2 x 18
2 x 182 x 20
2 x 18
2 x 182 x 202 x 182 x 182 x 20
1.02
1.020.81
1.02
1.020.811.021.020.81
0.82
0.820.52
0.82
0.820.520.820.820.52
PE
PVCPVC
PVC
PEPEPEPEPE
0.80
0.800.80
0.80
0.800.801.600.700.70
1.00
1.001.00
1.00
1.001.00
---
-
--
-
---
0.800.80
2.62 x 6.25
2.62 x6.252.41 x 5.83
2.62 x 6.25
2.62 x 6.252.41 x 5.834.22 x 7.174.02 x 8.053.81 x 7.63
23
2922
28
2418364940
72.6
22.235.2
72.6
22.235.222.222.235.2
6229
249288
249
622972027167
362409
875
460473
875
460473460460473
Notas: 1. DC resistance calculated based on a 17.93 ohm-mm2/km resistivity for Hard cooper and 58.62 ohm-mm2/km for steel copper covered.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
Hard CopperHard Copper
CopperClad Steel
CopperClad Steel
Hard CopperHard CopperHard CopperHard CopperHard Copper
2 x 18
DWP PVC
APPROX.TOTAL
WEIGTH(pound/kft)
INSULATIONMATERIAL
EXTERNALDIMENSIONS
(mils)
DCRESISTANCE
AT 20° C1
(ohm/kft)
INSULATIONRESISTANCE
(Mohm/kft)TYPE CONDUCTOR
CROSSSECTION
(kcmil)
INSULATIONTHICKNESS
(mils)
ONECONDUCTOR
TENSILE STRENGTH(Nominal)
(ksi)
JACKETTHICKNESS
(mils)SIZE
No. x AWG
SEPARATOR(mils)
STRANDDIAMETER
(mils)
DWP PE CCS
DWP PVC CCS
2 x 182 x 20
2 x 18
2 x 182 x 20
DWP PE
2 x 182 x 182 x 20
DWP 2PE
DWP PE-PVC
2 x 18
2 x 182 x 20
2 x 18
2 x 182 x 202 x 182 x 182 x 20
40
4032
40
4032404032
1.63
1.631.02
1.63
1.631.021.631.631.02
PE
PVCPVC
PVC
PEPEPEPEPE
31
3131
31
3131632828
39
3939
39
3939---
-
--
-
---
3131
103 x 246
103 x 24695 x 229
103 x 246
103 x 24695 x 229
166 x 282158 x 317150 x 300
15
2015
19
1612253327
22.1
6.7710.7
22.1
6.7710.76.776.7710.7
6229
817944
817
204372362823514
11881342
875
6769
127
6769676769
25
Outside TelephoneWire DWTDrop Wire Twisted
Description
Drop Wire Twisted. Hard copper conductor, individually insulated with polyethyleneor PVC.
Construction
ConductorHard copper
InsulationBlack Polyethylene weather resistant or flame retardat PVC.
Application
Self supporting one pair twisted conductor Drop Wire intended for aerial serviceconnection to the subscriber
Standards
CENTELSA telephone wires DWT are manufactured under the following standards:NTC 1300 Service Drop telephone wire, inside installations and jumper.
Certifications
CENTELSA Outside Telephone Wire, are certified by:CIDET (Colombia). Standard NTC 1300.
Package100 or 200 meters spools in corrugated carton boxes
Note: other configurations and sizes not specified in this catalogue are availableupon request.
26
Outside Telephone Wire (International System Unit)Drop Wire Twisted
Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.
0.820.520.820.52
2 x 182 x 202 x 182 x 20
DWT PVCDWT PVCDWT PEDWT PE
1.020.811.020.81
249288
62297202
22.735.922.735.9
28212317
460473460473
0.800.800.800.80
2.622.412.622.41
5.254.835.254.83
APPROX.TOTAL
WEIGTH(kg/km)
CROSSSECTION
(mm2)
EXTERNALDIAMETER
(mm)
DCRESISTANT
AT 20°C1
(ohm/km)
INSULATIONRESISTANCE
(Mohm-km)
TYPE SIZENo. x AWG
STRANDDIAMETER
(mm)
ONE CONDUCTORTENSILE STRENGTH
(Nominal)(MPa)
INSULATIONTHICKNESS
(mm)
DIAMETEROVER
INSULATION(mm)
Notes: 1. DC resistance calculated based on a 10.785 ohm-cmil/ft resistivity for Hard cooper.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
Outside Telephone WireDrop Wire Twisted
Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.
1.631.021.631.02
2 x 182 x 202 x 182 x 20
DWT PVCDWT PVCDWT PEDWT PE
40324032
817944
2043723628
6.9011.06.9011.0
19141611
67696769
31313131
10395
10395
207190207190
APPROX.TOTAL
WEIGTH(pound/kft)
CROSSSECTION
(kcmil)
EXTERNALDIAMETER
(mils)
DCRESISTANT
AT 20°C1
(ohm/kft)
INSULATIONRESISTANCE
(Mohm-kft)
TYPE SIZENo. x AWG
STRANDDIAMETER
(mils)
ONE CONDUCTORTENSILE STRENGTH
(Nominal)(ksi)
INSULATIONTHICKNESS
(mils)
SEPARATOR(mils)
Notes: 1. DC resistance calculated based on a 17.93 ohm-mm2/km resistivity for Hard cooper.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
27
Description
Soft copper wires insulated with flame retardant PVC, paired, unshielded or shieldedwith aluminum foil and drain wire, external PVC jacket.
Construction
ConductorSoft copper
InsulationFlame retardant PVC
PairsTwo insulated conductor twisted together
CoreUp to 25 pairs one group of pairs, for 30 pairs and more, groups of 10 or 25 pairs.
Spare pairsOne pair color coded White-Red for 10 pairs or more.
IdentificationPairs, groups an units in the assembly core, are identified by color code (includedin this catalogue)
Core WrapNon hygroscopic polyester tape
ShieldUnshielded or shielded with aluminum foil and tinned copper drain wire
JacketFlame retardant PVC, gray colored.
Characteristics
Mutual capacitance120 nF/km.Capacitive Unbalance400 pF (referred to 500 m).
Inside Telephone Cables
28
DC Conductor Resistance97.8 ohm/km.
Maximum Operating Voltage60 V.
Insulation Resistance500 Mohm-km.
Dielectric Strength (60 seg)1000 V AC, 1500 V DC.
Applications
For inside residential commercial and industrial applications. Appropriatefor locations with electric interference produced by near power electric circuit.
Installation in dry locations in ducts trays and race ways.
Standards
CENTELSA Inside Cables are manufactured under the following standards:
NTC-983, IEC 189. Cables e hilos para bajas frecuencias con aislamientoy cubierta en PVC.
Notes: 1. Optionally with tinned copper conductor2. Other configurations and sizes not specified in this catalogue are available upon request.
29
Note: Data herein indicated are approximate and are subject to normal manufacturing tolerances.
Inside Unshielded Telephone Cable
Standards: Low Frecuency Cables and Wire with PVC Insulation and PVC Sheat.
NOMINALPAIRS
STANDARDLENGTHBY REEL
(m)
INSULATIONTHICKNESS
(mm)
APPROX.TOTAL WEIGTH
(kg/km)
OVERALLDIAMETER
(mm)
SPAREPAIRS
CONDUCTORDIAMETER
(mm)
JACKETTHICKNESS
(mm)
15222834404979
139168200255310424584
0.200.200.200.200.200.200.200.200.200.200.200.200.200.20
0.500.500.500.500.500.500.500.500.500.500.500.500.500.50
0.600.600.600.600.600.700.700.800.800.900.900.901.001.00
3.183.934.504.985.406.007.269.46
10.3211.3212.7213.9516.3119.03
1001000100010001000100020002000200020001500100010001000
123456
10202530405070
100
------11111111
Note: Data herein indicated are approximate and are subject to normal manufacturing tolerances.
Inside Unshielded Telephone Cable
Standards: Low Frecuency Cables and Wire with PVC Insulation and PVC Sheat.
16233036425181
142171204259314429590
0.200.200.200.200.200.200.200.200.200.200.200.200.200.20
0.500.500.500.500.500.500.500.500.500.500.500.500.500.50
0.600.600.600.600.600.700.700.800.800.900.900.901.001.00
3.364.114.685.165.586.187.449.64
10.5011.5012.9014.1316.4919.21
1001000100010001000100020002000200020001500100010001000
123456
10202530405070
100
------11111111
NOMINALPAIRS
STANDARDLENGTHBY REEL
(m)
INSULATIONTHICKNESS
(mm)
APPROX.TOTAL WEIGTH
(kg/km)
OVERALLDIAMETER
(mm)
SPAREPAIRS
CONDUCTORDIAMETER
(mm)
JACKETTHICKNESS
(mm)
30
Description
Twisted pair for cross connections, for inside use. Soft tinned copper insulatedwith PVC or PVC and Nylon, assembly in pairs, triads or quads.
Construction
ConductorSoft tinned copper wire
InsulationFlame retardant PVC for JWT.Flame retardant PVC insulation; abrasion oil and gasoline resistant Nylonjacket for JWT PVC-NY.
Applications
JWT: twisted telephone wire for inside use, cross connections, telephonicderivations and radio and TV equipment wiring.
JWT PVC-NY: connection wire in distributors, mini-distributors and telephonicequipment. Nylon jacket provides abrasion resistance.
JWT NY: connection wire in distributors, mini-distributors and telephonicequipment.
Radio and TV equipment wiring, weld able without remove the insulation,Diameter reduced tightness and low friction advantages given by Nyloninsulation. Installation in dry locations, ducts or open installation.
Standards
CENTELSA telephone wires JWT are manufactured under the followingstandards:NTC 1300 Service Drop telephone wire, inside installations and jumper.
Inside TelephoneWire JWTJumper Wire Twisted
31
CertificationsCENTELSA Outside Telephone Wire, are certified by:CIDET (Colombia). Standard NTC 1300.
Package100 or 200 meters spools in corrugated carton boxes
Note: other configurations and sizes not specified in this catalogue are availableupon request.
Notes: 1. DC resistance calculated based on a 17.93 ohm-mm2/km resistivity for Tinned cooper.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
Inside Telephone Wire JWT PVC(International System Units)Jumper Wire Twisted PVC
Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.
0.320.320.320.210.210.210.280.280.280.200.200.20
2 x 223 x 224 x 222 x 243 x 244 x 242 x 0.63 x 0.64 x 0.62 x 0.53 x 0.54 x 0.5
0.640.640.640.510.510.510.600.600.600.500.500.50
174174174180180180183183183183183183
57.457.457.491.091.091.066.066.066.095.095.095.0
8.412.616.8
5.48.1
10.97.6
11.315.1
5.27.9
10.5
0.300.300.300.250.250.250.300.300.300.250.250.25
1.241.241.241.011.011.011.201.201.201.001.001.00
2.492.683.002.022.182.442.402.592.902.002.162.41
SIZEAWG or mm
DCRESISTANCE
AT 20° C¹(ohm/km)
INSULATIONTHICKNESS
(mm)
APPROX.TOTAL WEIGTH
(kg/km)
OVERALLDIAMETER
(mm)
STRANDDIAMETER
(mm)
CROSSSECTION
(mm²)
EXTERNALDIAMETER
(mm)
INSULATIONRESISTANCE
(Mohm/km)
32
Inside Telephone Wire JWT PVC-NYJumper Wire Twisted PVC-Nylon
Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.
Notes: 1. DC resistance calculated based on a 10.785 ohm-cmil/ft resistivity for Tinned cooper.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
0.250.400.64
2 x 262 x 242 x 22
15.920.125.3
126108
91
44.427.717.5
2.63.75.3
4.34.34.3
38.042.247.4
75.984.394.7
6.76.76.7
29.333.538.7
Inside Telephone Wire JWT PVC-NY(International System Units)Jumper Wire Twisted PVC-Nylon
Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.
Notes: 1. DC resistance calculated based on a 17.93 ohm-mm2/km resistivity for Tinned cooper.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
APPROX.TOTAL
WEIGTH(kg/km)
CROSSSECTION
(mm2)
EXTERNALDIAMETER
(mm)
DCRESISTANCE
AT 20°C1
(ohm/km)
INSULATIONRESISTANCE
(Mohm-km)
SIZEAWG or mm
STRANDDIAMETER
(mm)
JACKETTHICKNESS
(mm)
DIAMETEROVER JACKET
(mm)
NSULATIONTHICKNESS
(mm)
DIAMETEROVER
INSULATION(mm)
0.130.210.320.130.200.28
2 x 262 x 242 x 222 x 0.42 x 0.52 x 0.6
0.400.510.640.400.500.60
393328393329
14691.057.414895.066.0
3.85.57.93.85.37.1
0.110.110.110.110.110.11
0.961.071.200.961.061.16
1.932.142.411.922.122.32
0.170.170.170.170.170.17
0.740.850.980.740.840.94
Inside Telephone Wire JWT PVCJumper Wire Twisted PVC
Standards: NTC 1300 Service Drop telephone wire, inside installations andjumper.
Notes: 1. DC resistance calculated based on a 17.93 ohm-mm2/km resistivity for Tinned cooper.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
0.640.640.640.400.400.40
2 x 223 x 224 x 222 x 243 x 244 x 24
252525202020
572572572592592592
17.517.517.527.727.727.7
5.78.5
11.33.65.57.3
11.811.811.89.89.89.8
48.948.948.939.839.839.8
97.9105.5118.179.685.896.1
SIZEAWG or mm
DCRESISTANCE
AT 20° C¹(ohm/kft)
INSULATIONTHICKNESS
(mils)
APPROX.TOTAL WEIGTH
(pound/kft)
OVERALLDIAMETER
(mils)
STRANDDIAMETER
(mils)
CROSSSECTION(sq inches)
EXTERNALDIAMETER
(mils)
INSULATIONRESISTANCE
(Mohm/kft)
APPROX.TOTAL
WEIGTH(kg/km)
CROSSSECTION(sq inches)
EXTERNALDIAMETER
(mils)
DCRESISTANCE
AT 20°C1
(ohm/km)
INSULATIONRESISTANCE
(Mohm-km)
SIZEAWG or mm
STRANDDIAMETER
(mils)
JACKETTHICKNESS
(mils)
DIAMETEROVER JACKET
(mils)
NSULATIONTHICKNESS
(mils)
DIAMETEROVER
INSULATION(mils)
33
Notes: 1. DC resistance calculated based on a 17.93 ohm-mm2/km resistivity for Tinned cooper.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
Inside Telephone Wire JWT NY(International System Units)Jumper Wire Twisted PVC-Nylon
Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.
0.130.210.320.130.200.28
2 x 262 x 242 x 222 x 0.42 x 0.52 x 0.6
0.400.510.640.400.500.60
101010101010
14691.057.414895.066.0
3.04.56.83.04.36.0
0.170.170.170.170.170.17
0.740.850.980.740.840.94
1.491.832.371.481.812.27
Inside Telephone Wire JWT NYJumper Wire Twisted PVC-Nylon
Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.
Notes: 1. DC resistance calculated based on a 10.785 ohm-cmil/ft resistivity for Tinned cooper.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
0.250.400.64
2 x 262 x 242 x 22
15.920.125.3
333333
44.427.717.5
2.03.04.6
6.76.76.7
29.333.538.7
58.672.293.4
SIZEAWG or mm
DCRESISTANCE
AT 20° C¹(ohm/km)
INSULATIONTHICKNESS
(mm)
APPROX.TOTAL WEIGTH
(kg/km)
DIAMETEROVER
INSULATION(mm)
STRANDDIAMETER
(mm)
CROSSSECTION
(mm²)
EXTERNALDIAMETER
(mm)
INSULATIONRESISTANCE
(Mohm/km)
SIZEAWG or mm
DCRESISTANCE
AT 20° C¹(ohm/kft)
INSULATIONTHICKNESS
(mils)
APPROX.TOTAL WEIGTH
(pound/kft)
DIAMETEROVER
INSULATION(mils)
STRANDDIAMETER
(mils)
CROSSSECTION(sq inches)
EXTERNALDIAMETER
(mils)
INSULATIONRESISTANCE
(Mohm/kft)
34
Description
Inside drop wire paralleled. Soft copper insulated with PVC.
Construction
ConductorSoft copper wire
InsulationFlame retardant white PVC, paralleled conductors with polarization ridge.
Applications
Paralleled telephone wire for inside use from the interior box to exterior box;telephonic derivations.
Installation in dry locations, ducts or open installation.
Standards
CENTELSA telephone wires JWP are manufactured under the followingstandards:NTC 1300 Service Drop telephone wire, inside installations and jumper.
Certifications
CENTELSA Outside Telephone Wire, are certified by:CIDET (Colombia). Standard NTC 1300.
Package100 or 200 meters spools in corrugated carton boxes
Note: other configurations and sizes not specified in this catalogue areavailable upon request.
Inside TelephoneWire JWPJumper Wire Parallel
35
Notes: 1. DC resistance calculated based on a 17.241 ohm-mm2/km resistivity for Soft cooper.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
Inside Telephone Wire JWP(International System Units)Jumper Wire Parallel
Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.
0.520.32
2 x 202 x 22
0.810.64
240279
33.954.2
18.113.5
0.600.60
2.01 x 4.031.84 x 3.69
Notes: 1. DC resistance calculated based on a 10.371 ohm-cmil/ft resistivity for Soft cooper.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
1.020.64
2 x 202 x 22
32.025.3
787914
10.316.5
12.29.1
23.623.6
79.3 x 158.572.6 x 145.1
Inside Telephone Wire JWPJumper Wire Parallel
Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.
SIZEAWG or mm
DCRESISTANCE
AT 20° C¹(ohm/km)
INSULATIONTHICKNESS
(mm)
APPROX.TOTAL WEIGTH
(kg/km)
STRANDDIAMETER
(mm)
CROSSSECTION
(mm²)
EXTERNALDIAMETER
(mm)
INSULATIONRESISTANCE
(Mohm/km)
SIZEAWG or mm
DCRESISTANCE
AT 20° C¹(ohm/kft)
INSULATIONTHICKNESS
(mils)
APPROX.TOTAL WEIGTH
(pound/kft)
STRANDDIAMETER
(mm)
CROSSSECTION
(kcmil)
EXTERNALDIAMETER
(mils)
INSULATIONRESISTANCE
(Mohm/kft)
34
Description
Inside drop wire paralleled. Soft copper insulated with PVC.
Construction
ConductorSoft copper wire
InsulationFlame retardant white PVC, paralleled conductors with polarization ridge.
Applications
Paralleled telephone wire for inside use from the interior box to exterior box;telephonic derivations.
Installation in dry locations, ducts or open installation.
Standards
CENTELSA telephone wires JWP are manufactured under the followingstandards:NTC 1300 Service Drop telephone wire, inside installations and jumper.
Certifications
CENTELSA Outside Telephone Wire, are certified by:CIDET (Colombia). Standard NTC 1300.
Package100 or 200 meters spools in corrugated carton boxes
Note: other configurations and sizes not specified in this catalogue areavailable upon request.
Inside TelephoneWire JWPJumper Wire Parallel
35
Notes: 1. DC resistance calculated based on a 17.241 ohm-mm2/km resistivity for Soft cooper.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
Inside Telephone Wire JWP(International System Units)Jumper Wire Parallel
Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.
0.520.32
2 x 202 x 22
0.810.64
240279
33.954.2
18.113.5
0.600.60
2.01 x 4.031.84 x 3.69
Notes: 1. DC resistance calculated based on a 10.371 ohm-cmil/ft resistivity for Soft cooper.2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.
1.020.64
2 x 202 x 22
32.025.3
787914
10.316.5
12.29.1
23.623.6
79.3 x 158.572.6 x 145.1
Inside Telephone Wire JWPJumper Wire Parallel
Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.
SIZEAWG or mm
DCRESISTANCE
AT 20° C¹(ohm/km)
INSULATIONTHICKNESS
(mm)
APPROX.TOTAL WEIGTH
(kg/km)
STRANDDIAMETER
(mm)
CROSSSECTION
(mm²)
EXTERNALDIAMETER
(mm)
INSULATIONRESISTANCE
(Mohm/km)
SIZEAWG or mm
DCRESISTANCE
AT 20° C¹(ohm/kft)
INSULATIONTHICKNESS
(mils)
APPROX.TOTAL WEIGTH
(pound/kft)
STRANDDIAMETER
(mm)
CROSSSECTION
(kcmil)
EXTERNALDIAMETER
(mils)
INSULATIONRESISTANCE
(Mohm/kft)
36
Electrical CharacteristicsOutside Telephone Cables
MUTUAL CAPACITANCE(nF/km)
SIZE (mm)
Nominal1Maximum averageMaximum individual
0.4525564
0.5525564
0.6525564
Conductor DC Resistance(ohm/km)
SIZE (mm)
Maximum averageMaximum individual
0.4144.0150.0
0.592.195.9
0.663.966.6
RESISTIVE UNBALANCE1
(%)SIZE (mm)
Maximum averageMaximum individual
0.42.05.0
0.51.55.0
0.61.54.0
1500 5000
INSULATION RESISTANCE(Mohm-km)
Filled Core Air Core
Conductor A vs Conductor B
Conductor vs Shield
2000V, 3s1000V, 60s
6000V, 3s3000V, 60s
1000V, 3s500V, 60s2000V, 3s
1000V, 60s
DIELECTRIC STRENGTH(Volts)
SOLIDPOLYETHYLENE
FOAM SKINPOLYETHYLENE
MAXIMUM AVERAGEATENUATION1
(db/km)
SIZE (mm)
A 1000 HzA 150 kHzA 772 kHz
0.41.8812.123.0
0.51.518.9018.4
0.61.266.9015.5
Notes: 1. Test or value not indicated in Standard NTC 2061.2. Data herein indicated are subject to normal tolerances.
Pair to pair (pF refered to 500m)Pair to shield1 (pF/km)
2502625
150-
CAPACITIVE UNBALANCE(pF refered to 500m)
INDIVIDUALVALUE
95%OF VALUES
CROSSTALK Power Sum dB/305m
ELFEXT
150772
160031506300
0.4 mm6147413529
0.5 mm6349423731
0.6 mm6349433731
0.4, 0.5 and 0.6 mm5743373125
Average AverageFrequencykHz
0.4, 0.5 and 0.6 mm5847433834
0.4, 0.5 and 0.6 mm5342383329
ELNEXTWorst Pair Worst Pair
37
Pairs Codes in 25 Pairs GroupsInside¹ and Outside Telephone Cables
123456789
10
WHITEWHITEWHITEWHITEWHITEREDREDREDREDRED
BLUEORANGEGREENBROWNGREYBLUE
NARANJAGREENBROWNGREY
PAIR No.INSULATION COLOR
CONDUCTOR A CONDUCTOR B
10 PAIRS GROUP COLOR CODE
123456789
10111213141516171819202122232425
WHITEWHITEWHITEWHITEWHITEREDREDREDREDRED
BLACKBLACKBLACKBLACKBLACK
YELLOWYELLOWYELLOWYELLOWYELLOWPURPLEPURPLEPURPLEPURPLEPURPLE
BLUEORANGEGREENBROWNGREYBLUE
ORANGEGREENBROWNGREYBLUE
ORANGEGREENBROWNGREYBLUE
ORANGEGREENBROWNGREYBLUE
ORANGEGREENBROWNGREY
PAIR No.INSULATION COLOR
CONDUCTOR A CONDUCTOR B
PAIRS CODES IN 25 PAIRS GROUPS
CONSTRUCTION GROUP No. PAIRS
GROUP IDENTIFICATION
BINDER COLOR
10 PAIRGROUPS
25 PAIRGROUPS
1234567123456789
101112
1 to 1011 to 2021 to 3031 to 4041 to 5051 to 6061 to 70
1 to 2526 to 5051 to 75
76 to 100101 to 125126 to 150151 to 175176 to 200201 to 225226 to 250251 to 275276 to 300
WHITE - BLUEWHITE - ORANGEWHITE - GREENWHITE - BROWNWHITE- GREYRED - BLUERED - ORANGEWHITE - BLUEWHITE - ORANGEWHITE - GREENWHITE - BROWNWHITE- GREYRED - BLUERED - ORANGERED - GREENRED - BROWNRED - GREYBLACK - BLUEBLACK - ORANGE
Note: 1. Specifications for inside telephone cables up to 100 pairs.
38
Unit Color Code IdentificationOutside Telephone Cables
25 PAIRS
1234
WHITE - BLUEWHITE - ORANGEWHITE - GREENWHITE - BROWN
CONSTRUCTION GROUP No. BINDER COLOR
IDENTIFICATION FOR 4 GROUPS IN 100 PAIRS UNITS
CONSTRUCTION UNIT No. BINDER COLOR
UNITS IDENTIFICATION
PAIRS
100 PAIRS UNIT(4 GROUPSOF 25 PAIRS
EACH)
123456789
101112131415161718192021222324
WHITE - BLUEWHITE - ORANGEWHITE - GREENWHITE - BROWNWHITE - GREYRED - BLUERED - ORANGERED - GREENRED - BROWNRED - GREYBLACK - BLUEBLACK - ORANGEBLACK - GREENBLACK - BROWNBLACK - GREYYELLOW - BLUEYELLOW - ORANGEYELLOW - GREENYELLOW - BROWNYELLOW - GREYPURPLE - BLUEPURPLE - ORANGEPURPLE - GREENPURPLE - BROWN
1 to 100101 to 200201 to 300301 to 400401 to 500501 to 600601 to 700701 to 800801 to 900
901 to 10001001 to 11001101 to 12001201 to 13001301 to 14001401 to 15001501 to 16001601 to 17001701 to 18001801 to 19001901 to 20002001 to 21002101 to 22002201 to 23002301 to 2400
39
PAIRS ASSEMBLY GROUPS BY UNIT
CORE ASSEMBLY IN GROUPS OR UNITS
PAIRS BY GROUP
102030405070
100150200300400500600900
12001500180021002400
(0+1)(0+2)(0+3)(0+4)(0+5)(1+6)(0+4)(1+5)(2+6)(3+9)(0+4)(0+5)(1+5)(2+7)(3+9)
(1+5+9)(2+6+10)(2+8+11)(2+8+14)
10101010101025252525252525252525252525
GROUPSGROUPSGROUPSGROUPSGROUPSGROUPSGROUPSGROUPSGROUPSGROUPS
UNITSUNITSUNITSUNITSUNITSUNITSUNITSUNITSUNITS
----------444444444
Unit Color Code IdentificationOutside Telephone Cables
40
Assembly and Identificationfor Multipair Telephone Cable CoreInside¹ and Outside Telephone Cables
20 Pairs Assembly (0+2)
20 to 70 pairs
10 PAIRS GROUP CABLES
WhiteOrange
WhiteBlue
50 Pairs Assembly (0+5)
WhiteGrey White
Blue
WhiteGreen
WhiteOrange
WhiteBrown
40 Pairs Assembly (0+4)
WhiteBrown
WhiteBlue
WhiteGreen
WhiteOrange
30 Pairs Assembly (0+3)
WhiteGreen
WhiteBlue
WhiteOrange
70 Pairs Assembly (1+6)
RedBlue
WhiteOrange
WhiteGrey
BlancoVerde
RedOrange
WhiteBrown
WhiteBlue
100 Pairs Assembly (0+4)
100 to 300 pairs
25 PAIRS GROUP CABLES
WhiteBrown
WhiteBlue
WhiteGreen
WhiteOrange
200 Pairs Assembly (2+6)
RedOrange
White Green
RedBlue
WhiteBrown
RedGreen
WhiteGrey
WhiteOrange
WhiteBlue
300 Pairs Assembly (3+9)
RedGrey White
Brown
RedGreen
WhiteGrey
BlackBlue
RedBlue
White Green
WhiteBlue
WhiteOrange
BlackOrange
RedOrange
RedBrown
150 Pairs Assembly (1+5)
WhiteOrangeWhite
Grey WhiteGreen
RedBlue
WhiteBrown
WhiteBlue
Note:: 1.Specifications for telephone cables up to 100 pairs.
41
1500 Pairs Assembly (1+5+9)400 Pairs Assembly (0+4)
400 to 2400 pairs
100 PAIRS UNIT CABLES(EACH UNIT 4 GROUPS OF 25 PAIRS)
WhiteBlue
WhiteOrange
WhiteGreen
WhiteBrown
2100 Pairs Assembly (2+8+11)
2400 Pairs Assembly (2+8+14)
1800 Pairs Assembly (2+6+10)
1200 Pairs Assembly (3+9)
RojoGris White
Brown
RedGreen
WhiteGrey
BlackBlue
RedBlue
WhiteGreen
WhiteBlue
WhiteOrange
BlackOrange
RedOrange
RedBrown
900 Pairs Assembly (2+7)
RedGreen White
Green
WhiteBrown
RedBlue White
Grey
WhiteOrange
WhiteBlue
RedBrown
RedOrange
600 Pairs Assembly (1+5)
WhiteGrey
WhiteOrange
WhiteGreen
RedBlue
WhiteBrown
WhiteBlue
500 Pairs Assembly (0+5)
WhiteGrey White
Blue
WhiteGreen
WhiteOrange
WhiteBrown
WhiteGrey
WhiteOrange
WhiteGreen
RedBlue
WhiteBrown
WhiteBlue
Black Grey
RedOrng
RedGreen
RedBrownRed
Grey
Black Blue
BlackOrng
BlackGreen
Black Brown
Yellow Green
Red Brown
RedGrey
Black Blue
BlackOrange
Black Green
BlackGrey
YellowBlue
YellowOrange
RedOrange
White Green
RedBlue
WhiteBrown
RedGreen
WhiteGrey
WhiteOrange
WhiteBlue
BlackBrown
Purple Blue
Black Blue
BlackOrange
BlackGreen
BlackBrown
Black Grey
YellowGreen
YellowBrown
YellowGrey
RedGreen
WhiteGreen
RedOrange
WhiteBrown
RedBrown
RedBlue
WhiteOrange
WhiteBlue
Yellow Blue White
Grey
RedGrey
YellowOrange
Purple Brown
Black Blue
BlackOrange
OrangeGreen
BlackGrey
Yellow Blue
YellowGrey
PurpleBlue
PurpleOrange
RedGreen
WhiteGreen
RedOrange
WhiteBrown
RedBrown
RedBlue
WhiteOrange
WhiteBlue
Yellow Green
WhiteGrey
RedGrey
YellowBrown
YellowOrange
BlackBrown
Purple Green
Assembly and Identificationfor Multipair Telephone Cable CoreInside¹ and Outside Telephone Cables