32 Channel Auto Searching

with Diversity ReceiverWireless FPV LCD Monitor

User Manual

Product description:：Super Slim, Wireless FPV monitor with dual receiver. LCD monitor is

a new multi-function product, adopting advanced integrated circuits

and high-quality new HD LCD monitor. It integrates a high-sensitivity

and auto searching of 32channels, dual 5.8GHZ AV wireless receivers,

aerial receiver and high-definition monitor. The Monitor casing is

compact, easy to operate and can be used for FPV ground station,

security monitoring, baby monitors, photography viewfinder,

construction site video surveillance.

The monitor has a built-in battery, if you don’t install the battery, you

can use the 9~18V power supply or use the battery plate for external

power supply.

To insure best use of the unit, please read the user’s manual carefully.

CAUTION 1. Do not use any damaged or leaking batteries and please replace

the battery immediately if its working life becomes short significantly

2. Do not expose this product to direct sunlight, heat or humid conditions

3. Keep away from strong light while using this product so as to obtain the clearest and the most colorful picture. Please use sun shade for outdoor use.

4. Please avoid heavy impact or drops on the ground. 5. Do not use chemical solutions to clean this unit. Please simply

wipe with a clean soft cloth.6. Please do not take apart or repair the unit by yourself.

Product features :

host, connecting multiple monitors.

1.8cm thick body

Build-in 5.8 GHz wireless receiver

channels

High Sensitivity:-90dBM, 5.8GHz wireless receiver, 32

Auto search

Non-blue screen

High brightness, contrast, high resolution

Built-in VIDEO/AUDIO input and output, HDMI input,

Color Control Systems

Headphone audio

Built-in battery and rear battery plate.

With VIDEO signal output function, can be used as video

Shortcuts key can adjust the brightness and check field.

Picture Screen Markers and Center Marker

CONTENTS

1. Product description ------------------------------- 4

2. Wireless receiver operation -------------------- 7

3. Operation instructions ---------------------------10

4. VIDEO input and output cable ------------------ 15

5. Sun shade installation and removal ---- 15

6. Power Supply------------------------------------------ 18

7. Parameters -------------------------------------------- 19

8. Trouble shooting ---------------------------------- 21

1. Product description

1.1 Front panel instruction:

４

12345678

12345678

9

10

9

10

In HDMI / VIDEO state: shortcut key for check field.

In OSD menu state: UP for OSD Menu.

2. Multi button，brightness election/ chanel set / dowm.

In RF signal state: Press this button for channel selection

from “A、B、E、F” In OSD for “DOWN” button.

In HDMI / VIDEO signal state: press this button to adjust brightness.

In OSD menu state: Down for OSD menu.

3. MENU: Menu button, as exit button when on BAND selection.

4. : Volume up, press this key to increase the volume control,

menu item selection for settings adjustment.

5. : Volume down and center mark button, press this key for

center mark on/off. If would like to make the volume down,

press “ ” first and then press this button again for

adjustment. Menu item selection for settings adjustment

6. MODE: signals election.

7. : it will turn off/one after press this button for 3s.OFF/ON,

/BAND

1. : Multi button: Check Field/ Auto search/ Channel set/ up.

In RF signal state: Press this button for channel selection

:

5

8. Charge indicator light, it’s red when charging, it’s green when

charge is complete.

/CH/

1.2 Rear battery plate instruction:

1. USB Upgrade

2. DC OUT: DC power output. Can supply power to other

additional equipment. When the machine has an external

power supply, the output of the power supply voltage and the

external power supply voltage is the same. If is powered by the

built-in battery, the battery voltage of output supply will be same

as the built-in battery voltage. (Output power supply shall not

exceed 500mA when power is output form internal).

9. TFT screen

10. Terminal of receiver

6

1

3

2

4

56

7

8

3. DC IN: External power input. This machine can be powered

by external or internal power. If you want to use

another power adapter, please use a genuine power

supply in the DC9-18V, ≧1.2A. Range.

4. Battery plate

5. ：Stereo earphone jack

6. AV/OUT: AUDIO output port

7. AV/IN: AUDIO input port

8. HDMI IN: HDMI input port

7

2. Wireless receiver operation

This unit can auto search 32 channels.

(Frequency range of each region is different, please check the unit’s frequency chart below).

2.1 Channel selection: Wireless transmitter channel and receiver channel must be the same as the chart; otherwise it will not receive a signal.

8

Wireless 5.8GHz Diversity Receiver

BAND CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8

5865

5733

5705

5740 5760 5780 5800 5820 5840 5860 5880

5685 5665 5645 5885 5905 5925 5945

5752 5771 5790 5809 5828 5847 5866

5845 5825 5805 5785 5765 5745 5725A

B

E

F

2.2 Auto Search:

Turn on the monitor, press “MENU” and select “RF” signal input.

the top left corner of the screen. When the screen on the

/CH/

search has finished.

2.3 Manual Searching and setting:

Turn on the monitor, press “ MENU” and select “RF” signal

input. “BAND:X CH:X” will display on the top left corner of the

screen Press “ /BAND ” to switch channel A/B/E/F. Press

” ,“Auto Searching” will display on Long press “

upper left corner shows the BAND:X CH:X and images, the

9

the signal sent from the transmitter and display it on the monitor.

“ ” to select 1~8 channel. The receiver will receive /CH/

10

● RF Status Auto Search：Long press(≥3S），for

channel auto search.

Manual Tuning：to select 1~8 channel.

● VIDEO Status

No menu shows, change R/G/B/Mono/Color

3.1 Button instructions: nottub ybdnatS

MODE Input Signal selection button

menu item selection for settings adjustment.

Volume down and center mark button press this key

for center mark on/off. If would like to make the

Volume down, press “ ” firstly and then press this

button for adjustment. Menu item selection for

settings adjustment.

MENU Menu key, exit button when on BAND selection

Multi button, different functions in different input

status

3. Operating instructions

/CH/

10

Multi button，different functions in different input

status:

● RF Status

Manual Tuning, to switch channel A/B/E/F.

● VIDEO Status

No menu shows, press this button to change 6

brightness levels

2 Menu instructions

Press "MENU" to enter the menu, use the " " or "/BAND"

button to select "Color、MENU、Function、Volume", select it and

press " " or " " button to confirm, enter the submenu

Operation, use the " " or " /BAND" button select the

adjustment item. After selecting adjustment item, press the "MENU"

once again to confirm, press "MENU" key to exit the OSD menu.

11

/BAND

/CH/

/CH/

OSD

Color

※Brightness: To adjust the image's brightness.

※Contrast: To adjust the brightnest ratio of the Image.

※ Hue : On NTSC Video mode, the image color tint difference

is adjustable by hue.

※ Saturation: To adjust color concentration

※ Check Field: Switch on/off Check Field (Red、Green、、 Blue

Monochromatic and Color)

12

※ Language: Languages for OSD as below:

English、简体中文、François、Italia no、Deutsch

Español、日本語、 、 Pycc 、Portuguesa

※ H Position：To adjust the OSD horizontal position.

※ V Position：To adjust the OSD in vertical position.

※ OSD Timeout：To adjust the clock.

※ Transparent：To adjust the level of transparency.

Function

● Reset: Back to original setting.

● System: To adjust color video format, PAL/NTSC.

한국의

13

※ Display Ratio: To change the display ratio 16:9/4:3.

Screen Markers: To adjust screen marker（off，96%，

93%，90%，85%，80%）

Centre Markers：To set centre mark (cross mark)

display

Camera: Use the Canon 5 d II or similar camera, the

monitor video has a real-time image. NO black screen,

NO delay.

●

●

●

Sound

※ Volume : To adjust the volume.

14

4. VIDEO input and output cable

3.5mm plug for VIDEO input and output. (see the picture as above)

Use No.1 plug for the VIDEO input and output

Yellow RCA: VIDEO input or output port

Red RCA: AUDIO R input or output port

White RCA: AUDIO L input or output port

※ Focus: As an auxiliary function (in HDMI mode ) when used

as the camera viewfinder.

※ Ver.1.1: Software version number

15

1

23

4

① ②

● Sun shade installation view

The sun shade’s hanging clip and the monitor’s sun shade

slot should be aligned with the hole and slide down.

② Please follow the above steps, otherwise the cover will

③

①

16

be damaged.

5. Sun shade installation and removeal

● Remove sun shade view:

①

② ③

5.2 Remove:

drag up shade cover from monitor, that separates the sun When you want to remove the shade cover from the monitor,

17

shade from the monitor.

6. Power Supply

6.1 There are two versions for power supply:

Supply by power adapter

To use a power adapter supply, choose the power adapter(optional) ,

which matches the monitor. If using another power adapter,

please use a power supply in the DC9-18V, ≧ 1.5A Range.

● Built-in Battery Power Supply

This model has a built-in Li-ion battery capacity: 7.4V-2200mA/h

(2Hours), after fully-charged, it will last 2 hours.

6.2 Power ouput :This machine can output the power by DC OUT port,

is the same. If powered by built-in battery, the battery voltage

of output supply will be same as the built-in battery voltage.

18

● External power supply

When the monitor is connect by the DC power adapter,

red light is illuminated, means is charging, after it is fully charged,

then it will switch to a green light.

When the machine has an external power supply, the output of

the power supply voltage and the external power supply voltage

● Over-charge and over-discharge, it will cause permanent

damage to the positive pole and negative pole of batteries.

6.3 Li-ion Battery:● The working temperature of Li-ion battery is -20~60℃, please

don’t use the battery in places with temperatures too low or to high.

The power of battery will be reduced if it is working in a low

temperature environment. Please don’t use the battery in high

temperature environment, may cause battery swell and catch fire.

Please check the temperature of battery when working in high temperature environment.

Do not over discharge then recharge the battery.

● Every now and then to do a deep charge and discharge the

battery to correct the consumption statistics, but it will not

improve your battery's actual capacity.

● Please be place in a cool place if you don’t use the battery for

●

discharge may damage the battery if you don’t use the

battery for long time.

7. Parameters

hcni0.7 DCL TFT ezis lenaP

DCL TFT epyt lenaP

Resolution 1024×600×RGB ＝1843200 Pixels

19

Please charge power battery to prevent self-discharge excessive

long time.

IPS thgilkcaB

)H( 51.0 x )W(50.0 hctip toD

9:61 oitar yalpsiD

/d mc 006 ssenthgirB 2

1:800 oitar tsartnoC

sm01 emit esnopseR

Viewing angle 80°/85°(L/R) 85°/85°(U/D)

IMDH/FR/oiduA/oediV langis tupnI

oediV langis tuptuO

Video color system

HDMI support format

720p /1080i /1080p (50/60Hz)

mm5.3 oeretstuptuo enohpdaeH

V81~9:CD egatlov tupnI

W31 noitpmusnoc rewoP ≦

RF receiving frequency 5.8 G broadband FM audio and video synchronization receiving (other frequencies optional)

different region) (different frequency range for

PAL-4.43 / NTSC-3.58

32 channel auto search

480i /480p /576i /576p

RF wireless receiving sensitivity

typical value -90dBm

8. Trouble shooting

8.1 Only black and white or monochrome picture:

① Please check saturation、brightness & contrast adjustment.

Under VIDEO/HDMI status, press to change the brightness.

② Please check monitor’s "color" from the menu "monochrome" is

in black and white or monochrome image or other condition.

Under VIDEO/HDMI status, Press to check,if RF status

then can be enter OSD.

③ Select OSD and choose "function" to check if the color format is

match with the video input format. Try to change other formats.

ytilibats ycneuqerF

Unit size (mm)

Unit weight 440g (Including the Li battery but

without antenna and battery plate)

Installation method 1/4 inch bracket screw holes, can

be easily connected to the hot

shoe mount, tripod fixed installation

Build-in battery Li-ion 7.4V/2200 mA/h

Working temperature －20～50℃

Storage temperature －30～65℃

190(L)x134(W)x18(H)mm

mpp 001±

21

/BAND

/CH/

8.2 NO picture after Turning on the power

Check signal cable contact are in good condition, a monitor is ①

synchronized with the input signal, and can press the

"SOURCE/EXIT" give it a try. If in the RF channel, please check

to see if the transmitter has been work.

Check signal cable connecting, and make sure use the standard ②

adapter connect the monitor. If power supply by battery, please

check the battery whether fully charged.

8.3 Images are not synchronized: ① Open OSD and choose "function" to check if the color format is match

with the video input format. Try to change the other formats. Pal/Ntsc

The RF signal is too weak.②

8.4 No sound:① Press the volume button "+", try increasing the volume.

② Check the AUDIO input and ensure there is an AUDIO singnal

Transmitting from transmitter when RF receiving.

8.5 RF, no signal detected: ① Transmitter is working properly or not.

② Transmitter frequency matches with the receiver frequency band.

③ If changed the receiving antenna, please note that must be matched

with the transmitter, otherwise may cause low receiving sensitivity

and can't receive signals.

④ Try re-searching or setting the channel by manual.

■ Remark: If there are still other problems, please contact our customer support

22