fhskitt03lnc bc2016 rev e fulham co. inc.: 12705 south van ness ave., hawthorne, ca 90250 tel.:...
TRANSCRIPT
20 6 Rev E1
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.Specifications subject to change without notice.
[email protected] www.fulham.com
Page 1 of 4
*For further detailed instructionsand list of kit components pleaserefer to the Installation Instructions.
*Self-Diagnostic Standard.*Self-Diagnostic comes factory disabled. Please reference pg.4 for more details.
• <4W Input Power
• To be operated with FHS1-UNV-3.6L only• 450 Lumen output
•
Wall Sconce and Ceiling Flush Mount compatible
General Specifications
Input Current
Input Power *Lumen Output * Maximum Output Current Output VoltageOutput Short Circuit Protection
Recharge Time RequiredBattery Type
Ambient Temperature
Surge Protection
Warranty
120V - 277V ± 10%, 47-63Hz
0.07A <4W
2.1 Amp. when used with # FHSBATT3-C3
3.6V Self resetting PTC24 Hrs.
UL 1310 / Class 2
C62.41 (TVS)
0°C - 50°C5 Years
450 Lumens
Battery Capacity AvailableNiCd 3.6VDC
Illumination Time
Output Classification
3Ah
145 Min.Estimated Run TimeMinimum 90 min
•
Low Level Lighting • Linear arrays are linkable
HotSpot UL Classified Kit components
Universal Voltage *
Over Current Protection Fuse
BC
A
B
C
D
134
D
C
B
A
4 3 2 1
2
DWG NO.SIZE REV
SHEET
PART NO.
SCALE
TITLE
DRAWN
CHKD
CHKD
UNLESS OTHERWISE SPECIFIED
APPROVALS DATE
DO NOT SCALE PRINT
1.0
FROM
1 OF 1THIS DRAWING IS THE PROPERTY OF FULHAM Co., INC AND CONTAINS PRIVILEGED OR CONFIDENTIAL INFORMATION. YOU WILL NOT DISCLOSE, USE, DISSEMINATE, DISTRIBUTE OR COPY THIS DRAWING FOR PURPOSES OTHER THAN WHAT IT IS INTENDED FOR. 4:5
12705 S. Van Ness Ave.Hawthorne, CA 90250 tel.: 1-323-779-2980, fax: 1-323-754-9060
DIMENSIONS ARE IN INCHES
MARCO LOPEZ
KAMRAN SARMADI
10/16/14
B
10/23/14
CHKD
FRONt VIEWLEFT VIEW
9" POLYGON LED ENGINE:TET120023RDXX-01, TET120018RDXX-01TET120023RDXX-11, TET120018RDXX-11TET120023RDXX-02, TET120018RDXX-02TET120023RDXX-12, TET120018RDXX-12
EDWIN REYES 10/23/14
See Title
9.00
2.33
4X0.188 TH
RU
0.8
0
1.30
1.5
0
0.25
Driver
8.00 B.C.
1.26
1.79
OBLIQUE VIEW
REVISIONS
ZONEREV. DESCRIPTION DATE APPROVED
1.0 INITIAL RELEASE
FHSKITT03LNC4W HotSpot UL Classified Kit
E365124E493705
BC
20 6 Rev E1
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.Specifications subject to change without notice.
[email protected] www.fulham.com
Page 2 of 4
Part Number Matrix
Mechanical Data
FHSBATT3-C3
1.201.541.64
FHS1-UNV-3.6L
FHS6-AR-3W-L LINEAR MODULE
HOLES: 2 - 0.169" x 0.205" [4.3mm x 5.2mm]
Retrofit TypeT = Troffer
TLED Wattage
03 = 3W
03 KIT
KIT CBattery Type
= C CellC LED Type
LN = Linear
LNFHSProduct Line
FHS = HotSpot
Top View
Top View
Top View
0
.18”
(4.6
mm
)
3.10”(78.77mm)
0.79”(20.12mm)
0
.827”
(21m
m)
1.09”(27.78mm)
0.70”(17.83mm)
4.685” (1198mm)
Side View
Side View
Emergency Driver
Battery
4.24”(107.69mm) 3.69” (93.72mm)
1.99” (50.54mm)
3.10” (78.74mm)
1.06”(26.92mm)
5.34”(135.63mm) 4.97”
(126.24mm)
4.24”(107.69mm)
4.24”(107.69mm)
4.24”(107.69mm)
R0.07”(R1.778mm)
0.81”(20.57mm)
4.67”(118.62mm)
FHSKITT03LNC4W HotSpot UL Classified Kit
E365124E493705
BC
20 6 Rev E1
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.Specifications subject to change without notice.
[email protected] www.fulham.com
Page 3 of 4
Wiring Diagram
12 1”+ 12 1”+ 24 1”+
WIRE
LENGTH - INCHES
BLACK WHITE BATTERY- LED ARRAY- TEST SWITCH- PILOT LIGHT
FHSKITT03LNC4W HotSpot UL Classified Kit
E365124E493705
BC
BATTERY LED ARRAY TEST
SWITCH
INPUTPOWER
FRONT VIEW RIGHT VIEW
FHS1-
UNV-3
.6L
WIRING DIAGRAM (TYP)
BLACK
WHITE(COMMON)
HOT( 100V ~ 277V)
BATTERY
TESTSWITCH
LED ARRAY
BLK
RED
IMPORTANT: Do not connect battery until fixture is installed
NOTE: In order to maintain proper operation and warranty coverage, the battery must be recharged once per year prior to installation.
IMPORTANT: Do not connect battery until fixture is installed
NOTE: In order to maintain proper operation and warranty coverage, the battery must be recharged once per year prior to installation.
20 6 Rev E1
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060.Specifications subject to change without notice.
[email protected] www.fulham.com
Page 4 of 4
TEST SWITCH OPERATIONS:
1. EM TEST : Press and hold test button for more than one second to enter EM mode for testing.
2. Manual Self-Diagnostic : After charging the battery for the specified recharge time, quickly press the test button three times within two seconds to force the controller to enter a Self-Diagnostic cycle. To quit the self-diagnostic cycleafter engaged press and hold the test button for ten seconds.
3. Enable/Disable Self-Diagnostic Status : Quickly press the test button two times within two seconds ,the monochromatic lamp displays the status of Self-Diagnostic Enable / Disabled settings.
4. Enable/Disable Auto Self-Diagnostic : Press and hold the test button for two seconds, then release and quickly press the test button two times, then release and press and hold the test button for two more seconds. When properly executed the indicator on the test button will display the flash mode for the Enable/Disable status. A flash of 2.5S on - 0.5S off means "Enabled", while a flash of 0.5S on - 2.5S off means "Disabled", the flashing will last for a few cycles.
LED indicator Status Comment Note
Permanent Red
Light/Solid System OK AC mode
Blinking ON
(4.5 sec on – 0.5 sec off)
Self-diagnose test
underwaySelf-Diagnostic
Blinking OFF
(0.5 sec on – 4.5 sec off)Charge circuit is broken Replace EM Driver
Fast Flashing
(0.5 sec on - 0.5 sec off)Battery not connected Connect battery pack.
Fast Flashing
(0.5 sec on - 0.5 sec off)Battery failure Change the battery
Very Slow Flashing
(4 sec on – 4 sec off)
Over Circuit Protection
Error Triggered.
Check LED load or
check
EM driver.
AC power will need to be
cycled on/off as well as the
battery re-connected
FHS1-UNV-3.6L Status Indication - Single Color Indicator
SELF- DIAGNOSTIC INSTRUCTIONS / OPERATION:
If the self-diagnostic feature is enabled:The emergency LED driver will conduct a self-check for thirty (30) seconds every thirty (30) days; and a ninety (90) minute self-check every 12 months. After every self-check the LED indicator light will indicate a status signal. Check indicator status chart above to diagnose the status signal.
If the self-diagnostic feature is disabled:User must conduct a manual test every thirty (30) days to ensure the emergency LED light source illuminates as intended. A full discharge test shall be conducted once a year; the LED light source shall illuminate for a minimum of ninety (90) minutes.
*Self-Diagnostic feature is factory disabled
Test Switch Indicator Status
FHSKITT03LNC4W HotSpot UL Classified Kit
E365124E493705
BC