fanuc fault codes ba 400

86
FM/BM 1xxx/2xxx Version F_02 / 13.08.2008 WeK 1 / 86 T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot FM 1000 MOVE Z-AXIS AS DOWN AS POSSBLE Cause: The brake test of Z-axis during teststop was not successful Effect: Remedy: Note: FM 1001 Z-AXIS BRAKE TEST FAILED Cause: The brake test of Z-axis during teststop was not successful Effect: Remedy: Note: FM 1002 CNC NOT READY "F1.7" Cause: The NC is not ready Effect: The Machine can not be turned ON Remedy: See detailed Alarmlist (also Fanuc) Note: FM 1003 BATTERY STATUS LOW Cause: The Battery status is low Effect: Non Remedy: While machine is turned ON replace battery Note: DO NOT TURN OFF MACHINE - LOOSE REFERENCE POINT FM 1004 FUSE TRIPPED "F10" Cause: Fuse has been tripped Effect: Feed stop / spindle stop Start lock Remedy: Insert fuse Check circuit / input Note:

Upload: andrew-beaumont

Post on 02-Mar-2015

1.624 views

Category:

Documents


14 download

TRANSCRIPT

Page 1: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 1 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1000 MOVE Z-AXIS AS DOWN AS POSSBLE

Cause: The brake test of Z-axis during teststop was not successful

Effect:

Remedy:

Note:

FM 1001 Z-AXIS BRAKE TEST FAILED

Cause: The brake test of Z-axis during teststop was not successful

Effect:

Remedy:

Note:

FM 1002 CNC NOT READY "F1.7"

Cause: The NC is not ready

Effect: The Machine can not be turned ON

Remedy: See detailed Alarmlist (also Fanuc)

Note:

FM 1003 BATTERY STATUS LOW

Cause: The Battery status is low

Effect: Non

Remedy: While machine is turned ON replace battery

Note: DO NOT TURN OFF MACHINE - LOOSE REFERENCE POINT

FM 1004 FUSE TRIPPED "F10"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

Page 2: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 2 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1005 FUSE TRIPPED "F11"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

FM 1006 FUSE TRIPPED "F12"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

FM 1007 FUSE TRIPPED "F36"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

FM 1008 FUSE TRIPPED "F40"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

Page 3: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 3 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1009 FUSE TRIPPED "F44"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

FM 1010 FUSE TRIPPED "F32"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

FM 1011 FUSE TRIPPED "FA10"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

FM 1012 FUSE TRIPPED "FA1"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

Page 4: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 4 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1013 FUSE TRIPPED "FA8"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

FM 1014 FUSE TRIPPED "FA12"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

FM 1015 FUSE TRIPPED "FA16"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

FM 1016 FUSE TRIPPED "FA32"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

Page 5: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 5 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1017 FUSE TRIPPED "FA34"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

FM 1018 FUSE TRIPPED "FA36"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

FM 1019 FUSE TRIPPED "FA40"

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

FM 1020 FUSE TRIPPED

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy: Insert fuse

Check circuit / input

Note:

Page 6: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 6 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1021 MAX END POSITION AXES ""

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1022 OVLD C/LUBE "ZS-Q12"

Cause: Over-current trigger for lubrication has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check the circuits of the lubrication unit (motor may be blocked)

Switch the trigger into the circuit

Note:

FM 1023 OVLD COOLANT "S271"

Cause: Over-current trigger for coolant system has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check currents

Switch the trigger into the circuit

Note: Compact system: all triggers for coolant. Systems with additional container (ASI): auxiliary drives except for coolant pumps (external/internal cooling)

FM 1024 OVLD HYDRAULIC "HY-Q10"

Cause: Over-current trigger for hydraulic system has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check the circuits of the hydraulic unit

Switch the trigger into the circuit

Note:

Page 7: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 7 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1025 OVLD HEAT EXCH "Q14/16"

Cause: Over-current trigger for cooling system has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1026 OVLD EXHAUSTSY "Q18"

Cause: Over-current trigger for air exhaust system has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check the circuits

Switch the trigger into the circuit

Note:

FM 1027 NO 24V FROM SW "S270"

Cause: Coolant: 24 V power supply (outputs) not reporting

Effect: Feed stop / spindle stop

Start lock

Remedy: Check 24-V power supply

Note: Signal is only available if a coolant is turned on. Switch cabinet on the KLM

FM 1029 SERVO NOT RDY "SA#2"

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

Page 8: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 8 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1030 MAIN PWR MODUL NOT RDY "CX3:3"

Cause: Drive train: supply/ monitoring module 1 not reporting ready for operation

Effect: Feed stop / spindle stop

Start lock

Remedy: Emergency STOP + RESET, then delete error(s)

Note: Look for other alarms

FM 1031 MAIN PWR MODUL NOT RDY

Cause: Drive train: supply/ monitoring module 2 not reporting ready for operation

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1032 ALARM SPINDLE 1 "ALMA"

Cause: Fanuc Alarm Spindle 1 occured

Effect: Feed stop / spindle stop

Start lock

Remedy: RESET or turn OFF and ON the machine

Note: For further information see Fanuc "Maintance manual"

FM 1033 ALARM SPINDLE 2 "ALMB"

Cause: Fanuc Alarm Spindle 2 occured

Effect: Feed stop / spindle stop

Start lock

Remedy: RESET or turn OFF and ON the machine

Note: For further information see Fanuc "Maintance manual"

Page 9: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 9 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1034 SERVO NOT RDY "SA"

Cause: The Servo Modul is not ready

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1035 POLE DETECT.SPDL NOT PROCESSED

Cause: Pole detection on synchron spindle is not processed

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1036 POLE DETECT.AXIS NOT PROCESSED

Cause: Pole detection on ETEL axis is not processed

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1037 BKW COOLER NOT RDY "S150"

Cause: Cooling unit not ready for operation

Effect: Feed stop / spindle stop

Start lock

Remedy: JOG + error delete key

Note: Note any additional messages (check filling level of water)

Page 10: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 10 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1038 ELEC.CAB-COOLER NOT RDY

Cause: Electrical cabinet cooler not ready for operation

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1039 HYDR OIL MIN LEVEL "HY-B141"

Cause: Hydraulics: oil level low

Effect: Feed stop / spindle stop

Start lock

Remedy: Fill up hydraulic oil

Note:

FM 1040 NO SYSTM HYDR PRS "HY-B130"

Cause: Hydraulics: system pressure monitoring has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check hydraulics

Note:

FM 1041 HYDR RETURN FILTR DIRTY

Cause: Hydraulics: return filter dirty

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

Page 11: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 11 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1042 OVRHEATED HYDR TEMP "HY-B132"

Cause: Hydraulics: temperature monitoring has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Cool off hydraulics, find out reason for heating up

Note:

FM 1043 HYD FILTER DIRTY

Cause: Hydraulics: filter dirty

Effect: Feed stop / spindle stop

Start lock

Remedy: Replace filter

Note:

FM 1044 MAGAZIN BALANCE N.OK "S416/417"

Cause: Magazine has engaged out of neutral position

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1045 TANKLOAD PRS NOT REACHED

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

Page 12: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 12 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1046 NO SYSTM PNEUM PRS "PN-B122"

Cause: Pneumatic system pressure has dropped

Effect: Feed stop / spindle stop

Start lock

Remedy: Check air supply

Check pressure switch

Note:

FM 1048 MAINTENANCE DOOR NOT CLOSED

Cause: Maintenance door is not closed

Switch from maintenance door has no respond

Effect: Feed stop / spindle stop

Start lock

Remedy: Press "DELETE FAULT MESSAGE" button

Check door switch

Note:

FM 1049 SETUP DOOR N.LOCKED "MA-7S1-4"

Cause: Interlock switch for partition wall is not locked

Effect: Feed stop / spindle stop

Start lock

Remedy: Close partition wall, check interlock switch

Note: 2-slot machines only

FM 1050 LOAD DOOR N.UNLOCKED "MA-S401"

Cause: Interlock switch for loading door is not unlocked

Effect: Feed stop / spindle stop

Start lock

Remedy: Interlock magnet feedback, loading door missing

Note:

Page 13: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 13 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1051 MAG DOOR N.LOCKED "MA-S411"

Cause: Interlock switch for magazine door is not locked

Effect: Feed stop / spindle stop

Start lock

Remedy: Close magazine loading door, check lock switch of magazine loading door

Note:

FM 1052 LOAD DOOR N.OPENED "E363"

Cause: Landert drive for loading door has error upon opening

Effect: Feed stop / spindle stop

Start lock

Remedy: Check Landert/loading door

Note: No loading enable with robot operation (loading from above)

FM 1053 LOAD DOOR N.LOCKED "MA-S401"

Cause: Interlock switch for loading door is not locked

Effect: Feed stop / spindle stop

Start lock

Remedy: Check covering interlock

Note:

FM 1054 LOAD DOOR N.CALIBRATED "E364"

Cause: Landert drive for loading door is not calibrated

Effect: Feed stop / spindle stop

Start lock

Remedy: Close and open loading door with keys on control panel.

Check to ensure input door calibrated

Check Landert unit (mechanics, belt)

Note: Do not activate the counter direction directly after opening / closing; this will interrupt the calibration process in some circumstances (wait 2-3 sec.)

Page 14: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 14 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1055 SAFETY SWITCH SIDE PAN

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1056 SAFETY SWITCH SIDE PAN

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1057 C/LUBE PRESSURE "ZS-B031"

Cause: Lubrication pressure of central lubrication reporting incorrect

Effect: Feed stop / spindle stop

Start lock

Remedy: Check lines and pressure switch of central lubrication

Note:

FM 1061 SP/LUBE OIL PRESS. "ZS-B033"

Cause: Grease pressure of spindle lubrication reporting wrong

Effect: Feed stop / spindle stop

Start lock

Remedy: Check lines and pressure switch for lubrication pressure in spindle lubrication

Note:

Page 15: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 15 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1062 SP/LUBE PNEU.PRESS "ZS-B032"

Cause: Pneumatic pressure of spindle lubrication reporting wrong

Effect: Feed stop / spindle stop

Start lock

Remedy: Check lines and pressure switch for pneumatic pressure in spindle lubrication

Note:

FM 1064 FUSE TRIPPED

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1065 FUSE TRIPPED

Cause: Fuse has been tripped

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1072 FAULT PROG NR CONVERSION

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

Page 16: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 16 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1073 FAULT TRANSFER PROG NR TO CNC

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1080 COOLANT MIN LEVEL "S282"

Cause: Coolant: clean water floater switch reporting MIN

Effect: Feed stop / spindle stop

Start lock

Remedy: Fill with clean water, check floater switch

Note:

FM 1081 OVERFLOW COOLANT SYSTEM "S291"

Cause: Coolant: MAX clean water floater switch for belt filter system has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check MAX clean water floater switch,

drain out clean water

Note:

FM 1082 COOLANT MAX LEVEL "S280"

Cause: Coolant: swarf conveyor floater switch reporting MAX

Effect: Feed stop / spindle stop

Start lock

Remedy: Check lifting pump and floater switch

Note:

Page 17: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 17 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1083 CLEAN WATR MIN TURBO "S282"

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1084 MUDY WATR MAX TURBO "S291"

Cause: Coolant: MAX dirty water floater switch for turbo filter has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check dirty water floater switch,

drain out dirty water

Note:

FM 1085 PROGR COOLANT PRESSURE >70

Cause: Coolant pressure was programmed higher than 70 bar

Effect: Feed stop / spindle stop

Start lock

Remedy: Check NC program

#1132 < 70

Note:

FM 1086 MUDY WATR MIN TURBO "S303"

Cause: Coolant: MIN dirty water floater switch for turbo filter has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check MIN floater switch,

refill with water

Note:

Page 18: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 18 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1087 GREASE LUBRICATN MIN "B153"

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1088 Q POSITIONING PMC N.FINISHED

Cause: PMC positioning of rotary axis could not finished

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1089 PAIRCHEK Q-AXIS "S070/071"

Cause: Both limit switches of Q axis reporting (raised/lowered)

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note:

FM 1090 Q-AXIS N.ON 0 DEG "S390"

Cause: Software cam does not match travel movement

Effect: Feed stop / spindle stop

Start lock

Remedy: Check soft cam(s)

Note: By authorized personnel only

Page 19: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 19 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1091 Q-AXIS N.ON 180 DEG "S391"

Cause: Software cam does not match travel movement

Effect: Feed stop / spindle stop

Start lock

Remedy: Check soft cam(s)

Note: By authorized personnel only

FM 1092 Q-AXIS N.RAISED "S071"

Cause: Limit switch for swivel table not reporting raised

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note:

FM 1093 Q-AXIS N.LOCKED "S070"

Cause: Limit switch for swivel table not reporting lowered

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note:

FM 1095 Q-AXIS SIGNAL 0/180 (SOFTWARE)

Cause: Rotary table is out of software limit switches

Effect: Feed stop / spindle stop

Start lock

Remedy: Check softcam positions for rotary table

Move rotary table in singlemovement to defined position

Note:

Page 20: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 20 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1096 Q-AXIS NOT ON 0 DEGREE

Cause: Rotary table is not on 0 degree

Effect: Feed stop / spindle stop

Start lock

Remedy: Check softcam positions for rotary table 0 degree

Move rotary table in singlemovement to defined position

Note:

FM 1097 Q-AXIS NOT ON 180 DEGREE

Cause: Rotary table is not on 180 degree

Effect: Feed stop / spindle stop

Start lock

Remedy: Check softcam positions for rotary table 180 degree

Move rotary table in singlemovement to defined position

Note:

FM 1098 Q-AXIS N.IN DEFIND POSITION

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1100 PLEASE EXECUTE SAFE TEST

Cause: A teststop has to executed fter Power ON or after 24h runtime

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

Page 21: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 21 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1101 CNC ALARM PATH 1

Cause: PMC Alarm in Path 1

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1102 CNC ALARM PATH 2

Cause: PMC Alarm in Path 2

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1103 DCS ALARM

Cause: PMC Alarm in Path Dual Check Safety

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1104 A-POSITIONING PMC N.FINISHED

Cause: PMC positioning of axis could not be finished

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

Page 22: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 22 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1105 A-AXIS NOT RELEASED "HY-B101"

Cause: Axis lock is not released

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for A axis

Note:

FM 1106 A-AXIS NOT LOCKED "HY-B100"

Cause: Axis lock is not clamped

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for A axis

Note:

FM 1107 A-AXIS MOTOR OVERTEMP "X380"

Cause: Axis has over temperature

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1108 A-AXIS NOT IN HOME POSITION

Cause: Axis is not in swiveling position

Effect: Feed stop / spindle stop

Start lock

Remedy: Put A axis in homeposition

Check soft cams for homeposition

Note:

Page 23: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 23 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1109 A-COUNTERB.N.RELEASD "HY-B103"

Cause: Axis counterbearing lock is not released

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for A counterbearing

Note:

FM 1110 A-COUNTERB.NOT LOCKD "HY-B102"

Cause: Axis counterbearing lock is not clamped

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for A counterbearing

Note:

FM 1113 U-POSITIONING PMC N.FINISHED

Cause: PMC positioning of axis could not be finished

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1114 U-AXIS NOT RELEASED "HY-B111"

Cause: Axis lock is not released

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for U axis

Note:

Page 24: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 24 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1115 U-AXIS NOT LOCKED "HY-B110"

Cause: Axis lock is not clamped

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for U axis

Note:

FM 1116 U-AXIS MOTOR OVERTEMP "X381"

Cause: Axis has over temperature

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1117 U-AXIS NOT IN HOME POSITION

Cause: Axis is not in swiveling position

Effect: Feed stop / spindle stop

Start lock

Remedy: Put A axis in homeposition

Check soft cams for homeposition

Note:

FM 1118 U-COUNTERB.N.RELEASD "HY-B113"

Cause: Axis counterbearing lock is not released

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for U counterbearing

Note:

Page 25: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 25 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1119 U-COUNTERB.N.LOCKED "HY-B112"

Cause: Axis counterbearing lock is not clamped

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for U counterbearing

Note:

FM 1120 MAG POSITIONING NOT FINISHD

Cause: PMC positioning of axis could not be finished

Effect: Feed stop / spindle stop

Start lock

Remedy: Try again / if necessary Reset / machine Off-On

Note: Watch for additional NC alarms and report them to the SW customer service if necessary

FM 1121 MAG POSITION NOT FOUND

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1123 FAULT COUNTING MODE MAG

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

Page 26: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 26 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1127 SPINDEL TOOL NOT CLMPED CORRECT

Cause: Spidle tool ist not correctly tightened

Effect: Feed stop / spindle stop

Start lock

Remedy: Tool in spindle

Check tool clamping device

Note: See operating instructions

FM 1128 SPI 1 (A/D CONV) NO SIGNAL

Cause: Analog digital converter for tool clamping device 1: no signal from Fanuc module

Effect: Feed stop / spindle stop

Start lock

Remedy: Check adapter for tool clamping device / check analog module

Note: By authorized personnel only

FM 1129 TL-CLMP SPI 1 NOT RELEASED

Cause: Tool clamping device 1: unclamping error

Effect: Feed stop / spindle stop

Start lock

Remedy: Check tool / check tool clamping device signals

Note: See operating instructions and SW diagnostics

FM 1130 SPI 3 (A/D CONV) NO SIGNAL

Cause: Analog digital converter for tool clamping device 3: no signal from Fanuc module

Effect: Feed stop / spindle stop

Start lock

Remedy: Check adapter for tool clamping device / check analog module

Note: By authorized personnel only

Page 27: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 27 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1131 TL-CLMP SPI 3 NOT RELEASED

Cause: Tool clamping device 3: unclamping error

Effect: Feed stop / spindle stop

Start lock

Remedy: Check tool / check tool clamping device signals

Note: See operating instructions and SW diagnostics

FM 1133 LEAK DETECTION SP1

Cause: Spindle 1: leeking detection has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1134 LEAK DETECTION SP3

Cause: Spindle 3: leeking detection has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1136 SPI 2 (A/D CONV) NO SIGNAL

Cause: Analog digital converter for tool clamping device 2: no signal from Fanuc module

Effect: Feed stop / spindle stop

Start lock

Remedy: Check adapter for tool clamping device / check analog module

Note: By authorized personnel only

Page 28: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 28 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1137 TL-CLMP SPI 2 NOT RELEASED

Cause: Tool clamping device 2: unclamping error

Effect: Feed stop / spindle stop

Start lock

Remedy: Check tool / check tool clamping device signals

Note: See operating instructions and SW diagnostics

FM 1138 SPI 4 (A/D CONV) NO SIGNAL

Cause: Analog digital converter for tool clamping device 4: no signal from Fanuc module

Effect: Feed stop / spindle stop

Start lock

Remedy: Check adapter for tool clamping device / check analog module

Note: By authorized personnel only

FM 1139 TL-CLMP SPI 4 NOT RELEASED

Cause: Tool clamping device 4: unclamping error

Effect: Feed stop / spindle stop

Start lock

Remedy: Check tool / check tool clamping device signals

Note: See operating instructions and SW diagnostics

FM 1141 LEAK DETECTION.SP2

Cause: Spindle 2: leeking detection has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

Page 29: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 29 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1142 LEAK DETECTION.SP4

Cause: Spindle 4: leeking detection has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1144 PAIRCHK MAG SP 1 "PN-S010/011"

Cause: Both limit switches of tool magazine 1 interlock are unlocked/locked have engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

FM 1145 PAIRCHK MAG SP 2 "PN-S012/013"

Cause: Both limit switches of tool magazine 2 interlock are unlocked/locked have engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

FM 1147 PAIRCHK MAG-LOAD "PN-S042/043"

Cause: Both limit switches of loading slot interlock are unlocked/locked have engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

Page 30: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 30 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1148 PAIRCHK MAG-LOAD 2

Cause: Both limit switches of loading slot interlock are unlocked/locked have engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

FM 1149 PAIRCHK MAG-COVR "PN-S020/021"

Cause: Both limit switches of the left magazine covering OPEN/CLOSED have engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

FM 1150 PAIRCHK MAG-CVR 2 "PN-S022/023"

Cause: Both limit switches of the right magazine covering OPEN/CLOSED have engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

FM 1151 PAIRCHK MAG-COVR

Cause: Both limit switches of the magazine forward / return have engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

Page 31: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 31 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1152 TL POS 1 NOT UNLOCKD "PN-S010"

Cause: Limit switch tool slot 1 is not unlocked

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

FM 1153 TL POS 2 NOT UNLOCKD "PN-S012"

Cause: Limit switch tool slot 2 is not unlocked

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

FM 1154 TL POS 1 NOT LOCKD "PN-S011"

Cause: Limit switch tool slot 1 is not locked

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

FM 1155 TL POS 2 NOT LOCKD "PN-S013"

Cause: Limit switch tool slot 2 is not locked

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

Page 32: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 32 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1156 LOAD PL. N.UNLOCKD "PN-S042"

Cause: Limit switch loading slot is not unlocked

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

FM 1157 LOAD PL.2 N.UNLOCKD

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1158 LOAD PL. N.LOCKD "PN-S043"

Cause: Limit switch loading slot is not locked

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

FM 1159 LOAD PL. 2 N.LOCKD

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

Page 33: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 33 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1160 MAG CVR NOT OPEN "PN-S020/022"

Cause: Limit switch for magazine covering is not open

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

FM 1161 MAG CVR N.CLOSED "PN-S021/023"

Cause: Limit switch for magazine covering is not closed

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

FM 1162 MAG N. ADVANCED

Cause: Limit switch for magazine holder is not advanced

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

FM 1163 MAG N. RETURNED

Cause: Limit switch for magazine holder is not retracted

Effect: Feed stop / spindle stop

Start lock

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

Page 34: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 34 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1164 TIMEOUT TOOLCHANGER

Cause: Tool change was not completed within the specified time frame

Effect: Feed stop / spindle stop

Start lock

Remedy: Move tool change to basic setting, basic setting key

Move tool change to basic setting via single movement. Check temporary storage of tool management

Note: For basic setting see the operating instructions

FM 1165 MAGAZINE LIST NOT EMPTY

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1168 NO TABLE CHOOSEN

Cause: Either Table 1 or Table 2 is selected

Effect: Feed stop / spindle stop

Start lock

Remedy: Select a table in the SW-Menue (CUSTOM)

Note: NC-PROG, F=1

FM 1169 WRONG TABLE POSITIONG

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

Page 35: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 35 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1170 Z-AXIS NOT START POS.(-50.0)

Cause: The Z-axis is to START NC program not MIN. position (> -50 mm)

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1171 NC-START W/ INVALID PROG DATA

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1172 MOVE Y-AXIS TO WORK AREA

Cause: Dual check safty and spindle pole detection requires Y axis in working area

Effect: Feed stop / spindle stop

Start lock

Remedy: Move Y axis manual into working area

Note:

FM 1173 Y-AXIS IN COLLISION AREA

Cause: Y axis is in the malfunction area of the Q axis

Effect: Feed stop / spindle stop

Start lock

Remedy: JOG: move axis out of malfunction area (>400) AUTO: machine must be in tool change area

Note:

Page 36: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 36 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1174 Z-AXIS IN COLLISION AREA

Cause: Z axis is outside the working area

Effect: Feed stop / spindle stop

Start lock

Remedy: JOG: move axis out of malfunction area (>400) AUTO: machine must be in tool change area

Note:

FM 1175 A-AXIS LOCKED IN LOAD AREA

Cause: Move command to axis in loading area

Effect: Feed stop / spindle stop

Start lock

Remedy: Check NC program

Note:

FM 1176 U-AXIS LOCKED IN LOAD AREA

Cause: Move command to axis in loading area

Effect: Feed stop / spindle stop

Start lock

Remedy: Check NC program

Note:

FM 1177 A-AXIS NO M11 PROGRAMMED

Cause: Interpolation programmed with A even though clamping monitoring of round axis is activated with M10

Effect: Feed stop / spindle stop

Start lock

Remedy: Program M11/M12

Note: M12 not possible for all machines

Page 37: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 37 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1178 U-AXIS NO M11 PROGRAMMED

Cause: Interpolation programmed with U/B even though clamping monitoring of round axis is activated with M10

Effect: Feed stop / spindle stop

Start lock

Remedy: Program M11/M12

Note: M12 not possible for all machines

FM 1180 NO T-FUNCTION PROGRAMMED

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1181 TOOL NOT FOUND

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1182 SPINDLE CONTAINS A TOOL

Cause: Tool managment: To unload or load a tool into the tool magazine is only possible when the spindle is empty

Effect: Feed stop / spindle stop

Start lock

Remedy: Put all tools out of spindle into magazine

Note:

Page 38: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 38 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1183 TOOL LIFE EXPIRED

Cause: If "TOOL LIFE MANGAMENT" active tool life is expired

Effect: Feed stop / spindle stop

Start lock

Remedy: Exchange tool and reset tool life in "TOOL LIFE MANGEMENT" for expiered tool

Note:

FM 1184 TOOL NUMBER OUT OF RANGE

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1185 W-POSITIONING PMC N.FINISHED

Cause: PMC positioning of axis could not be finished

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1186 W-AXIS NOT RELEASED "HY-B053"

Cause: Axis lock is not released

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for W axis

Note:

Page 39: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 39 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1187 W-AXIS NOT LOCKED "HY-B052"

Cause: Axis lock is not clamped

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for W axis

Note:

FM 1188 W-AXIS MOTOR OVERTEMP "X383"

Cause: Axis has over temperature

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1189 W-AXIS NOT IN HOME POSITION

Cause: Axis is not in swiveling position

Effect: Feed stop / spindle stop

Start lock

Remedy: Put A axis in homeposition

Check soft cams for homeposition

Note:

FM 1190 W-AXIS LOCKED IN LOAD AREA

Cause: Move command to axis in loading area

Effect: Feed stop / spindle stop

Start lock

Remedy: Check NC program

Note:

Page 40: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 40 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1191 W-AXIS NO M15 PROGRAMMED

Cause: Interpolation programmed with W even though clamping monitoring of round axis is activated with M13

Effect: Feed stop / spindle stop

Start lock

Remedy: Program M11/M12

Note: M12 not possible for all machines

FM 1192 FIX 1 T1 N.CLAMPED "HY-B080"

Cause: Pressure switch for clamping circuit 1 table 1 not reporting

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for clamping circuit 1 table 1

Note:

FM 1193 FIX 2 T1 N.CLAMPED "HY-B082"

Cause: Pressure switch for clamping circuit 1 table 1 not reporting

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for clamping circuit 2 table 1

Note:

FM 1194 FIX 3 T1 N.CLAMPED "HY-B"

Cause: Pressure switch for clamping circuit 1 table 1 not reporting

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for clamping circuit 3 table 1

Note:

Page 41: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 41 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1195 FIX 4 T1 N.CLAMPED "HY-B"

Cause: Pressure switch for clamping circuit 1 table 1 not reporting

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for clamping circuit 4 table 1

Note:

FM 1201 PAIRCHK SETUP DOOR "S392/S396"

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1202 PAIRCHK SETUP DOOR "S394/S397"

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1203 PAIRCHK SETUP DOOR "S393/S90"

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

Page 42: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 42 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1204 PAIRCHK SETUP DOOR "S395/S90"

Cause:

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1208 FIX 1 T2 N.CLAMPED "HY-B090"

Cause: Pressure switch for clamping circuit 1 table 2 not reporting

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for clamping circuit 1 table 2

Note:

FM 1209 FIX 2 T2 N.CLAMPED "HY-B092"

Cause: Pressure switch for clamping circuit 2 table 2 not reporting

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for clamping circuit 2 table 2

Note:

FM 1210 FIX 3 T2 N.CLAMPED "HY-B"

Cause: Pressure switch for clamping circuit 3 table 2 not reporting

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for clamping circuit 3 table 2

Note:

Page 43: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 43 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1211 FIX 4 T2 N.CLAMPED "HY-B"

Cause: Pressure switch for clamping circuit 4 table 2 not reporting

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for clamping circuit 4 table 2

Note:

FM 1214 FIX 5 T1 N.CLAMPED

Cause: Pressure switch for clamping circuit 5 table 1 not reporting

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for clamping circuit 5 table 1

Note:

FM 1215 FIX 5 T2 N.CLAMPED

Cause: Pressure switch for clamping circuit 5 table 2 not reporting

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for clamping circuit 5 table 2

Note:

FM 1220 W2-POSITIONING PMC N.FINISHD

Cause: PMC positioning of axis could not be finished

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

Page 44: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 44 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1221 W2-AXIS NOT RELEASED "HY-B053"

Cause: Axis lock is not released

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for U axis

Note:

FM 1222 W2-AXIS NOT LOCKED "HY-B052"

Cause: Axis lock is not clamped

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for U axis

Note:

FM 1223 W2-AXIS MOTOR OVERTEMP "X385"

Cause: Axis has over temperature

Effect:

Remedy:

Note:

FM 1224 W2-AXIS NOT IN HOME POSITION

Cause: Axis is not in swiveling position

Effect: Feed stop / spindle stop

Start lock

Remedy: Put A axis in homeposition

Check soft cams for homeposition

Note:

Page 45: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 45 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1225 W2-AXIS NO M15 PROGRAMED

Cause: Interpolation programmed with W2 even though clamping monitoring of round axis is activated with M13

Effect: Feed stop / spindle stop

Start lock

Remedy: Program M11/M12

Note: M12 not possible for all machines

FM 1226 W2-AXIS LOCKED IN LOAD AREA

Cause: Move command to axis in loading area

Effect: Feed stop / spindle stop

Start lock

Remedy: Check NC program

Note:

FM 1230 C-POSITINING PMC N.FINISHED

Cause: PMC positioning of axis could not be finished

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1231 C-AXIS NOT RELEASED "HY-B051"

Cause: Axis lock is not released

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for U axis

Note:

Page 46: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 46 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1232 C-AXIS NOT LOCKED "HY-B050"

Cause: Axis lock is not clamped

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for U axis

Note:

FM 1233 C-AXIS MOTOR OVERTEMP "X382"

Cause: Axis has over temperature

Effect:

Remedy:

Note:

FM 1234 C-AXIS NOT IN HOME POSITION

Cause: Axis is not in swiveling position

Effect: Feed stop / spindle stop

Start lock

Remedy: Put A axis in homeposition

Check soft cams for homeposition

Note:

FM 1235 C-AXIS LOCKED IN LOAD AREA

Cause: Move command to axis in loading area

Effect: Feed stop / spindle stop

Start lock

Remedy: Check NC program

Note:

FM 1236 C-AXIS NO M15 PROGRAMMED

Cause: Interpolation programmed with C/U even though clamping monitoring of round axis is activated with M10

Effect: Feed stop for all axes

Remedy: Program M11/M12

Note: M12 not possible for all machines

Page 47: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 47 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1238 C2-POSITIONING PMC N.FINISHD

Cause: PMC positioning of axis could not be finished

Effect: Feed stop / spindle stop

Start lock

Remedy:

Note:

FM 1239 C2-AXIS NOT RELEASED "HY-B051"

Cause: Axis lock is not released

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for U axis

Note:

FM 1240 C2-AXIS NOT LOCKED "HY-B050"

Cause: Axis lock is not clamped

Effect: Feed stop / spindle stop

Start lock

Remedy: Check pressure and pressure switch for U axis

Note:

FM 1241 C2-AXIS MOTOR OVERTEMP "X384"

Cause: Axis has over temperature

Effect:

Remedy:

Note:

Page 48: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 48 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1242 C2-AXIS NOT IN HOME POSITION

Cause: Axis is not in swiveling position

Effect: Feed stop / spindle stop

Start lock

Remedy: Put A axis in homeposition

Check soft cams for homeposition

Note:

FM 1243 C2-AXIS LOCKED IN LOAD AREA

Cause: Move command to axis in loading area

Effect: Feed stop / spindle stop

Start lock

Remedy: Check NC program

Note:

FM 1244 C2-AXIS NO M15 PROGRAMMED

Cause: Interpolation programmed with C2 even though clamping monitoring of round axis is activated with M10

Effect: Feed stop / spindle stop

Start lock

Remedy: Program M11/M12

Note: M12 not possible for all machines

FM 1250 SPINDEL 1 NOT ORIENTATED

Cause: Spindle 1: signal for spindle set up +/- monitoring limits missing

Effect: Feed stop / spindle stop

Start lock

Remedy: Check spindle control

Note: Spindle may be blocked or moving with difficulty

Page 49: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 49 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1251 SPINDEL 2 NOT ORIENTATED

Cause: Spindle 2: signal for spindle set up +/- monitoring limits missing

Effect: Feed stop / spindle stop

Start lock

Remedy: Check spindle control

Note: Spindle may be blocked or moving with difficulty

FM 1252 SPINDEL 3 NOT ORIENTATED

Cause: Spindle 3: signal for spindle set up +/- monitoring limits missing

Effect: Feed stop / spindle stop

Start lock

Remedy: Check spindle control

Note: Spindle may be blocked or moving with difficulty

FM 1253 SPINDEL 4 NOT ORIENTATED

Cause: Spindle 4: signal for spindle set up +/- monitoring limits missing

Effect: Feed stop / spindle stop

Start lock

Remedy: Check spindle control

Note: Spindle may be blocked or moving with difficulty

FM 1260 BLUM LASER NOT OK

Cause:

Effect:

Remedy:

Note:

FM 1261 TOOL 1 BROKEN

Cause:

Effect:

Remedy:

Note:

Page 50: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 50 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1262 TOOL 2 BROKEN

Cause:

Effect:

Remedy:

Note:

FM 1263 TOOL 3 BROKEN

Cause:

Effect:

Remedy:

Note:

FM 1264 TOOL 4 BROKEN

Cause:

Effect:

Remedy:

Note:

FM 1265 LEUZE LASER NOT OK

Cause:

Effect:

Remedy:

Note:

FM 1266 LEUZE LASER DIRTY

Cause:

Effect:

Remedy:

Note:

Page 51: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 51 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1280 ARTIS CHANNEL 1 NOT READY

Cause:

Effect:

Remedy:

Note:

FM 1281 ARTIS CHANNEL 2 NOT READY

Cause:

Effect:

Remedy:

Note:

FM 1282 ARTIS CHANNEL 3 NOT READY

Cause:

Effect:

Remedy:

Note:

FM 1283 ARTIS CHANNEL 4 NOT READY

Cause:

Effect:

Remedy:

Note:

FM 1284 ARTIS PROGAM NUMBER WRONG

Cause:

Effect:

Remedy:

Note:

Page 52: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 52 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1285 ARTIS PROGR.TRANSFORM.WRONG

Cause:

Effect:

Remedy:

Note:

FM 1290 FAULT MARPOSS 1

Cause:

Effect:

Remedy:

Note:

FM 1291 BATTERY ALARM MARPOSS 1

Cause:

Effect:

Remedy:

Note:

FM 1292 FAULT MARPOSS 2

Cause:

Effect:

Remedy:

Note:

FM 1293 BATTERY ALARM MARPOSS 2

Cause:

Effect:

Remedy:

Note:

Page 53: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 53 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1300 BALLUFF SYSTEM NOT READY

Cause:

Effect:

Remedy:

Note:

FM 1301 BALLUFF CODETAG 1 NOT PRESENT

Cause:

Effect:

Remedy:

Note:

FM 1302 BALLUFF CODETAG 2 NOT PRESENT

Cause:

Effect:

Remedy:

Note:

FM 1303 TOOL NOT FOR MACHINE S/N

Cause:

Effect:

Remedy:

Note:

FM 1304 TOOL AND POCKET ID MISSMATCH

Cause:

Effect:

Remedy:

Note:

Page 54: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 54 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1305 TOOL ID 1 AND ID 2 MISSMATCH

Cause:

Effect:

Remedy:

Note:

FM 1306 TOOL LENGTH DATA MISSMATCH

Cause:

Effect:

Remedy:

Note:

FM 1307 TOOL DATA OUT OF RANGE

Cause:

Effect:

Remedy:

Note:

FM 1310 MM-INCH - CHECK RESOLUTION

Cause: Milimter or inch was changed

check between SW option and Fanuc option does not match

Effect:

Remedy:

Note:

FM 1311 SET SPINDLE DIRECTION

Cause: The Spindle direction is not set

Effect: Feed stop / spindle stop

Start lock

Remedy: Set spindle direction as neccessary

Turn OFF and ON the machine

Note:

Page 55: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 55 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

FM 1312 CHECK SPINDLE DIRECTION

Cause: The Spindle direction has to be checked

Effect: Feed stop / spindle stop

Start lock

Remedy: Check changed spindle direction

Note:

FM 1313 PLEASE TURN OFF-ON MACHINE

Cause: SW options were changed

Effect:

Remedy:

Note:

FM 1314 MOVE SEL AXIS MIN 1 ROTATION

Cause: During reference move selected axis minimum 1 motor rotation

Effect:

Remedy:

Note:

BM 2001 MAGZN BALANCE TRIPPED

Cause:

Effect:

Remedy:

Note:

BM 2002 C/LUBE OIL PREWARN "ZS-B120"

Cause: Oil level prewarning for lubrication unit

Effect: None

Remedy: Fill lubricant unit oil to MAX

Note:

Page 56: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 56 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2003 C/LUBE MIN LEVEL "ZS-B121"

Cause: Oil level minimum for lubrication unit

Effect: Next Start lock

Remedy: Fill lubricant unit oil to MAX

Note:

BM 2004 SP/LUBE PREWRN LEVEL

Cause: Oil level prewarning for spindle lubrication unit

Effect: None

Remedy: Fill spindle lubricant unit oil to MAX

Note:

BM 2005 SP/LUBE MIN LEVEL

Cause: Oil level minimum for spindle lubrication unit

Effect: Next Start lock

Remedy: Fill spindle lubricant unit oil to MAX

Note:

BM 2006 HYDRAULIC OIL PREWRN

Cause: Hydraulics: oil minimum level

Effect: Next Start lock

Remedy: Fill oil until oil to MAX

Note:

BM 2007 HYDR RETRN FILTR DIRTY

Cause: Hydraulics: return filter dirty

Effect: Next Start lock

Remedy: Replace return filter

Note:

Page 57: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 57 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2008 HYDR FILTER DIRTY "HY-B143"

Cause: Hydraulics: filter dirty

Effect: Next Start lock

Remedy: Replace filter

Note:

BM 2010 FILTR AIR PURGE DIRTY

Cause: Air purge filter for measuring system dirty

Effect:

Remedy:

Note:

BM 2011 EXHAUSTSYSTEM DIRTY

Cause: Filter for exhuast system dirty

Effect:

Remedy:

Note:

BM 2012 MTR OVLD EXHAUSTSYSTEM "Q18"

Cause: Over-current trigger for air exhaust system has engaged

Effect:

Remedy:

Note:

BM 2016 TL SP 1 CLAMPED TO SHORT

Cause: Tool clamping device 1: clamping error, too short

Effect: Feed / spindle stop

Remedy: Check tool / check tool clamping device signals

Note: See operating instructions and SW diagnostics

Page 58: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 58 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2017 TL SP 1 CLAMPED TO LONG

Cause: Tool clamping device 1: clamping error, too long

Effect: Feed / spindle stop

Remedy: Tool / check tool clamping device signals / clamping jaw

Note: See operating instructions and SW diagnostics

BM 2018 TL SP 1 NOT SEATED CORRECT

Cause: Tool clamping device 1: plane surface error

Effect: Feed / spindle stop

Remedy: Check tool / check tool clamping device signals

Note: See operating instructions and SW diagnostics

BM 2020 TL SP 2 CLAMPED TO SHORT

Cause: Tool clamping device 2: clamping error, too short

Effect: Feed / spindle stop

Remedy: Check tool / check tool clamping device signals

Note: See operating instructions and SW diagnostics

BM 2021 TL SP 2 CLAMPED TO LONG

Cause: Tool clamping device 2: clamping error, too long

Effect: Feed / spindle stop

Remedy: Tool / check tool clamping device signals / clamping jaw

Note: See operating instructions and SW diagnostics

BM 2022 TL SP 2 NOT SEATED CORRECT

Cause: Tool clamping device 2: error, no plane surface

Effect: Feed / spindle stop

Remedy: Check tool / check tool clamping device signals

Note: See operating instructions and SW diagnostics

Page 59: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 59 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2024 MAGZIN NOT LOCKED "PN-S011/013"

Cause: Limit switch tool slot 1/2 is not locked

Effect: Tool change will not be performed any more

Remedy: Check proximity switch

Note: See operating instructions and SW diagnostics

BM 2025 NO ENABLE TURN MAGAZINE

Cause:

Effect:

Remedy:

Note:

BM 2028 COOLNT TEMP NOT REACHED

Cause:

Effect:

Remedy:

Note:

BM 2029 FAULT COOLNT HEATR "S260"

Cause:

Effect:

Remedy:

Note:

BM 2030 MIN LEVEL BKW COOLER "S151"

Cause: MIN coolant for BKW cooler

Effect: Start lock

Remedy: Fill with coolant to MAX

Note:

Page 60: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 60 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2031 OVRLOAD COOLANT "S271"

Cause: Over-current trigger for coolant system has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check currents

Switch the trigger into the circuit

Note: Compact system: all triggers for coolant. Systems with additional container (ASI): auxiliary drives except for coolant pumps (external/internal cooling)

BM 2032 OVRLOAD CHIPCNV "S272"

Cause: Over-current trigger for chipconveyor has engaged

Effect: Feed stop / spindle stop

Start lock

Remedy: Check currents

Switch the trigger into the circuit

Note:

BM 2033 DUBBEL FILTER DIRTY "S290"

Cause: Coolant: double filter dirty

Effect: Start lock

Remedy: Switch / replace filter

Note:

BM 2034 PAPER BAND FINISHED "S293"

Cause: Coolant: fleece end

Effect: Start lock

Remedy: Replace paper roll, check switch on the roll

Note:

BM 2035 RUN TIME PAPER BAND EXCEEDED

Cause: Coolant: fleece drive runtime monitoring

Effect: Start lock

Remedy: Check switch on belt drive, belt drive

Note: Intended to prevent unnecessary use of paper

Page 61: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 61 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2036 PRES SW TURBOFILTR "S291"

Cause: Coolant: error in turbo filter system pressure switch

Effect: Start lock

Remedy: Pressure switch reporting too long (> 15 sec.) during cleaning

Note: Clean turbo filter

BM 2037 PRES SW.TURBOFILTR ACCUMULATED

Cause:

Effect:

Remedy:

Note:

BM 2038 COOLANT MIN PREWRN "S273"

Cause: Coolant: floater switch prewarning for belt filter system minimum

Effect: Start lock

Remedy: Check floater switch,

refill with water

Note: The message can be eliminated by the next end of program with the error delete key.

BM 2039 MUD WATR PREWARN TURBO "S273"

Cause: Coolant: MIN dirty water floater switch prewarning for turbo filter has engaged

Effect: Start lock

Remedy: Check MIN pre-warning floater switch,

refill with water

Note:

BM 2040 COOLANT MIN LEVEL "S282"

Cause: Coolant: floater switch minimum for belt filter system

Effect:

Remedy:

Note:

Page 62: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 62 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2041 MUDY WATR MAX TURBO "S291"

Cause:

Effect:

Remedy:

Note:

BM 2042 COOLANT MAX LEVEL "S280"

Cause: In the swarf conveyor is to much water

Effect:

Remedy:

Note:

BM 2043 TL SP 3 CLAMPED TO SHORT

Cause: Tool clamping device 3: clamping error, too short

Effect: Feed / spindle stop

Remedy: Check tool / check tool clamping device signals

Note: See operating instructions and SW diagnostics

BM 2044 TL SP 3 CLAMPED TO LONG

Cause: Tool clamping device 3: clamping error, too long

Effect: Feed / spindle stop

Remedy: Tool / check tool clamping device signals / clamping jaw

Note: See operating instructions and SW diagnostics

BM 2045 TL SP 3 NOT SEATED CORRECT

Cause: Tool clamping device 3: plane surface error

Effect: Feed / spindle stop

Remedy: Check tool / check tool clamping device signals

Note: See operating instructions and SW diagnostics

Page 63: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 63 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2046 TL SP 4 CLAMPED TO SHORT

Cause: Tool clamping device 4: clamping error, too short

Effect: Feed / spindle stop

Remedy: Check tool / check tool clamping device signals

Note: See operating instructions and SW diagnostics

BM 2047 TL SP 4 CLAMPED TO LONG

Cause: Tool clamping device 4: clamping error, too long

Effect: Feed / spindle stop

Remedy: Tool / check tool clamping device signals / clamping jaw

Note: See operating instructions and SW diagnostics

BM 2048 TL SP 4 NOT SEATED CORRECT

Cause: Tool clamping device 4: error, no plane surface

Effect: Feed / spindle stop

Remedy: Check tool / check tool clamping device signals

Note: See operating instructions and SW diagnostics

BM 2050 LOAD DOOR N.UNLOCKED "MA-S401"

Cause: Interlock from loading door is not unlocked

Effect: None

Remedy: Interlock magnet feedback, loading door missing

Note:

BM 2052 LOAD DOOR NOT OPENED "E363"

Cause: Landert drive for loading door has error upon opening

Effect: None

Remedy: Check Landert/loading door

Note: No loading enable with robot operation (loading from above)

Page 64: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 64 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2053 LOAD DOOR N.LOCKED "MA-S401"

Cause: Interlock from loading door is not locked

Effect: Machine not ready

Remedy: Check covering interlock

Note:

BM 2060 TOOL BROKEN ARTIS CHANNEL 1

Cause:

Effect:

Remedy:

Note:

BM 2061 TOOL MISSING ARTIS CHANNEL 1

Cause:

Effect:

Remedy:

Note:

BM 2062 TOOL WORN ARTIS CHANNEL 1

Cause:

Effect:

Remedy:

Note:

BM 2063 TOOL BROKEN ARTIS CHANNEL 2

Cause:

Effect:

Remedy:

Note:

Page 65: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 65 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2064 TOOL MISSING ARTIS CHANNEL 2

Cause:

Effect:

Remedy:

Note:

BM 2065 TOOL WORN ARTIS CHANNEL 2

Cause:

Effect:

Remedy:

Note:

BM 2066 TOOL BROKEN ARTIS CHANNEL 3

Cause:

Effect:

Remedy:

Note:

BM 2067 TOOL MISSING ARTIS CHANNEL 3

Cause:

Effect:

Remedy:

Note:

BM 2068 TOOL WORN ARTIS CHANNEL 3

Cause:

Effect:

Remedy:

Note:

Page 66: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 66 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2069 TOOL BROKEN ARTIS CHANNEL 4

Cause:

Effect:

Remedy:

Note:

BM 2070 TOOL MISSING ARTIS CHANNEL 4

Cause:

Effect:

Remedy:

Note:

BM 2071 TOOL WORN ARTIS CHANNEL 4

Cause:

Effect:

Remedy:

Note:

BM 2072 ARTIS REWORK ACTIVE

Cause:

Effect:

Remedy:

Note:

BM 2074 A-AXIS NOT IN HOME POSITION

Cause: Axis is not in swiveling position

Effect:

Remedy:

Note:

Page 67: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 67 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2075 U-AXIS NOT IN HOME POSITION

Cause: Axis is not in swiveling position

Effect:

Remedy:

Note:

BM 2076 C-AXIS NOT IN HOME POSITION

Cause: Axis is not in swiveling position

Effect:

Remedy:

Note:

BM 2077 W-AXIS NOT IN HOME POSITION

Cause: Axis is not in swiveling position

Effect:

Remedy:

Note:

BM 2078 C2-AXIS NOT IN HOME POSITION

Cause: Axis is not in swiveling position

Effect:

Remedy:

Note:

BM 2079 W2-AXIS NOT IN HOME POSITION

Cause: Axis is not in swiveling position

Effect:

Remedy:

Note:

Page 68: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 68 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2108 EMERGENCY STOP "P1-S400"

Cause: EMERGENCY STOP button pressed

Effect: Machine cannot be turned on

Remedy: Free the EMERGENCY STOP button

Check the EMERGENCY STOP circuit

Note:

BM 2111 SETUP DOOR NOT CLOSED "MA-7S1-4"

Cause:

Effect:

Remedy:

Note:

BM 2114 TLCHANGR NOT IN HOME POSITION

Cause: Tool changer not in basic setting

Effect: Feed stop, no tool change possible

Remedy: Move tool change to basic setting with basic setting key

Note: See operating instructions

BM 2115 FUSE TRIPPED

Cause:

Effect:

Remedy:

Note:

BM 2120 SINGLE STEP MODE ACTIVE

Cause: Key "Single movement" is selected

Effect: Only JOG or INCJ Mode is possible

Additional movements are allowed

Remedy: Turn off "Singlemovement"

Check key switch if working properly

Note: By authorized personnel only (JOG/REF: SK: user consent if everything is OK)

Page 69: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 69 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2121 ELEC.CABINT TEMP NOT OK "A11.6"

Cause: The electrical cabinet temperature is to high

Effect: None

Remedy: Check cooler in electrical cabinet

Check adjusted temperature

Note:

BM 2122 MACHINING W/O COOLANT SYSTEM

Cause: Option Bit for "No Coolant" is selected

Effect: No coolant available

Remedy: Select with option bit the "Coolant System"

Note: See Keeprelais list or machine documentation

BM 2123 Q-AXIS NOT REFERENCED

Cause: Q axis absolute encoder not adjusted

Effect: The axis can only be moved when the axis selection key is pressed to avoid collisions

Remedy: Calibrate the Q axis measuring system

Note: By authorized personnel only (JOG/REF: SK: user consent if everything is OK)

BM 2124 X-AXIS NOT REFERENCED

Cause: X axis absolute encoder not adjusted

Effect: The axis can only be moved when the axis selection key is pressed to avoid collisions

Remedy: Calibrate the X axis measuring system

Note: By authorized personnel only

BM 2125 Y-AXIS NOT REFERENCED

Cause: Y axis absolute encoder not adjusted

Effect: The axis can only be moved when the axis selection key is pressed to avoid collisions

Remedy: Calibrate the Y axis measuring system

Note: By authorized personnel only

Page 70: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 70 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2126 Z-AXIS NOT REFERENCED

Cause: Z axis absolute encoder not adjusted

Effect: The axis can only be moved when the axis selection key is pressed to avoid collisions

Remedy: Calibrate the Z axis measuring system

Note: By authorized personnel only

BM 2127 A-AXIS NOT REFERENCED

Cause: A axis absolute encoder not adjusted

Effect: The axis can only be moved with the axis selection key pressed to avoid collisions

Remedy: Calibrate the A axis measurement system

Note: By authorized personnel only

BM 2128 U-AXIS NOT REFERENCED

Cause: U axis absolute encoder not adjusted

Effect: The axis can only be moved with the axis selection key pressed to avoid collisions

Remedy: Calibrate the U axis measurement system

Note: By authorized personnel only

BM 2129 MAGAZINE NOT REFERENCED

Cause: MAG axis absolute encoder not adjusted

Effect: The axis can only be moved with the axis selection key pressed to avoid collisions

Remedy: Calibrate the MAG axis measurement system

Note: By authorized personnel only

BM 2130 C-AXIS NOT REFERENCED

Cause: C axis absolute encoder not adjusted

Effect: The axis can only be moved with the axis selection key pressed to avoid collisions

Remedy: Calibrate the C axis measurement system

Note: By authorized personnel only

Page 71: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 71 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2131 W-AXIS NOT REFERENCED

Cause: W axis absolute encoder not adjusted

Effect: The axis can only be moved with the axis selection key pressed to avoid collisions

Remedy: Calibrate the W axis measurement system

Note: By authorized personnel only

BM 2132 CABINT DOOR NOT CLOSED "KE14"

Cause:

Effect:

Remedy:

Note:

BM 2133 C2-AXIS NOT REFERENCED

Cause: C2 axis absolute encoder not adjusted

Effect: The axis can only be moved with the axis selection key pressed to avoid collisions

Remedy: Calibrate the C2 axis measurement system

Note: By authorized personnel only

BM 2134 W2-AXIS NOT REFERENCED

Cause: W2 axis absolute encoder not adjusted

Effect: The axis can only be moved with the axis selection key pressed to avoid collisions

Remedy: Calibrate the W2 axis measurement system

Note: By authorized personnel only

BM 2138 MAGAZINE LOAD DOOR NOT LOCKED

Cause: Magazine loading door interlock switch closed not reporting

Effect: Magazine cannot be moved

Remedy: Close magazine loading door, check lock switch of magazine loading door

Note:

Page 72: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 72 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2139 LOADG.UNIT AT TL MAGAZN ACTIVE

Cause: Loading console for tool magazine turned on

Effect: Machine control panel is locked

Remedy: Turn off tool magazine control panel

Check tool magazine control panel switch

Note:

BM 2140 LOAD/UNLOAD ONLY IN JOG MODE

Cause: Tool management: loading/unloading of tools only possible in JOG and RESET state

Effect: No loading/unloading of tools possible

Remedy: JOG - RESET- new selection

Note:

BM 2141 LOAD/UNLOAG MAGAZINE ACTIVE

Cause: Loading and unloading activated with key switch

Effect: Control panel locked

Remedy: Complete load/unload tool function

Note:

BM 2148 NO PROGRAM MODE SELECTED

Cause: No program operating mode selected (F/C)

Effect: Start lock

Remedy: Select operating program (F/C) in JOG, MSST key

Note: Please note: in F mode, the selected program (SIEMENS selection) is started, not the program from the SW program list.

BM 2149 NO PROGRAM ENTRY

Cause: SW menu: no program entry

Effect: Start lock

Remedy: Select program in SW menu

Note: See operating instructions

Page 73: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 73 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2151 LOAD DOOR FAULT 1 (LANDERT)

Cause: Landert drive for loading door reporting malfunction 1 (general malfunctions)

Effect: Feed and spindle stop / start lock

Remedy: Check Landert/loading door

Note:

BM 2152 LOAD DOOR FAULT 2 (LANDERT)

Cause: Landert drive for loading door has malfunction: obstruction

Effect:

Remedy: Check loading door for ease of motion

Note:

BM 2155 SAFTY STRIP LOAD DOOR

Cause:

Effect:

Remedy:

Note:

BM 2156 LOAD DOOR NOT CLOSED

Cause: Landert drive for loading door has error upon closing

Effect: Start lock

Remedy: Check Landert/loading door

Note:

BM 2158 Q-AXIS NOT IN DEFINED POS.

Cause: Table setting not correct

Effect: No additional functions possible

Remedy: Check position of Q axis 0/180 degrees, check soft cam, cycle swivel carrier system, NCK reset if required

Note: By authorized personnel only

Page 74: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 74 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2164 FIXTURE T1 NOT IN LOAD/UNL.POS

Cause: Table A is not in the unloading or loading position to open the clamping device

Effect: Clamping mechanism for table A is not releasing

Remedy: Move table A to correct position, SW menu: setup axes basic setting value

Note: Basic setting / cycle key

BM 2165 FIXTURE T1 NOT CLAMPED

Cause: Fixture table 1 not clamped

Effect: No other functions are possible

Remedy: Clamp Fixture

Note:

BM 2166 FIX 1 T1 N.CLAMPED "HY-B080"

Cause: Pressure switch for clamping circuit 1 table 1 not reporting

Effect: Clamped message not reached

Remedy: Check pressure and pressure switch for clamping circuit 1 table 1

Note:

BM 2167 FIX 2 T1 N.CLAMPED "HY-B082"

Cause: Pressure switch for clamping circuit 2 table 1 not reporting

Effect: Clamped message not reached

Remedy: Check pressure and pressure switch for clamping circuit 2 table 1

Note:

BM 2168 FIX 3 T1 N.CLAMPED "HY-B"

Cause: Pressure switch for clamping circuit 3 table 1 not reporting

Effect: Clamped message not reached

Remedy: Check pressure and pressure switch for clamping circuit 3 table 1

Note:

Page 75: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 75 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2169 FIX 4 T1 N.CLAMPED "HY-B"

Cause: Pressure switch for clamping circuit 4 table 1 not reporting

Effect: Clamped message not reached

Remedy: Check pressure and pressure switch for clamping circuit 4 table 1

Note:

BM 2171 TOOL DETAIL - TOOL BLOCKED

Cause:

Effect:

Remedy:

Note:

BM 2172 TOOL DETAIL - PREWARN LIMIT

Cause:

Effect:

Remedy:

Note:

BM 2173 TOOL DETAIL -

Cause:

Effect:

Remedy:

Note:

BM 2174 TOOL DETAIL -

Cause:

Effect:

Remedy:

Note:

Page 76: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 76 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2175 TOOL DETAIL -

Cause:

Effect:

Remedy:

Note:

BM 2180 FIXTURE T2 NOT IN LOAD/UNL.POS

Cause: Table U is not in the unloading or loading position to open the clamping device

Effect: Clamping mechanism for table U is not releasing

Remedy: Move table U to correct position, SW menu: setup axes basic setting value

Note: Basic setting / cycle key

BM 2181 FIXTURE T2 NOT CLAMPED

Cause: Fixture table 2 not clamped

Effect: No other functions are possible

Remedy: Clamp Fixture

Note:

BM 2182 FIX 1 T2 N.CLAMPED "HY-B090"

Cause: Pressure switch for clamping circuit 1 table 2 not reporting

Effect: Clamped message not reached

Remedy: Check pressure and pressure switch for clamping circuit 1 table 2

Note:

BM 2183 FIX 2 T2 N.CLAMPED "HY-B092"

Cause: Pressure switch for clamping circuit 2 table 2 not reporting

Effect: Clamped message not reached

Remedy: Check pressure and pressure switch for clamping circuit 2 table 2

Note:

Page 77: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 77 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2184 FIX 3 T2 N.CLAMPED "HY-B"

Cause: Pressure switch for clamping circuit 3 table 2 not reporting

Effect: Clamped message not reached

Remedy: Check pressure and pressure switch for clamping circuit 3 table 2

Note:

BM 2185 FIX 4 T2 N.CLAMPED "HY-B"

Cause: Pressure switch for clamping circuit 4 table 2 not reporting

Effect: Clamped message not reached

Remedy: Check pressure and pressure switch for clamping circuit 4 table 2

Note:

BM 2186 FAULT AIR CONTROL 1 TABLE 1

Cause:

Effect:

Remedy:

Note:

BM 2187 FAULT AIR CONTROL 1 TABLE 2

Cause:

Effect:

Remedy:

Note:

BM 2188 FAULT AIR CONTROL 2 TABLE 1

Cause:

Effect:

Remedy:

Note:

Page 78: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 78 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2189 FAULT AIR CONTROL 2 TABLE 2

Cause:

Effect:

Remedy:

Note:

BM 2190 FIX 5 T1 N.CLAMPED

Cause:

Effect:

Remedy:

Note:

BM 2191 FIX 5 T2 N.CLAMPED

Cause:

Effect:

Remedy:

Note:

BM 2196 CONFIRM R/TABLE MISSING

Cause: No acknowledgement of fitting

Effect: Table not dividing, BSTQ lamp remains dark

Remedy: Confirm acknowledgement of fitting,

check key

Note: Look for any additional messages, SPVO clamped, etc.

BM 2197 CONFIRM - NO TOOL IN MAGAZINE

Cause:

Effect:

Remedy:

Note:

Page 79: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 79 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2200 MAINTENANCE REQUIRED

Cause:

Effect:

Remedy:

Note:

BM 2201 MAINTENANCE OVERTIME

Cause:

Effect:

Remedy:

Note:

BM 2212 SPI 1 TOLERANCE BAND "SPALA"

Cause:

Effect:

Remedy:

Note:

BM 2213 SPI 1 SPEED NOT ZERO "SSTA"

Cause: Spindle 1: standstill signal +/- monitoring limits missing

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

BM 2214 SPI 1 NO SPEED DETECT "SDTA"

Cause: Spindle 1: No speed detected

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

Page 80: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 80 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2215 SPI 1 SPEED NOT REACHED "SARA"

Cause: Spindle 1: Commanded spindle speed not reached

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

BM 2216 SPI 1 NOT ORIENTED "ORARA"

Cause: Spindle 1: Spindle not orientated (M19)

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

BM 2220 SPI 2 TOLERANCE BAND "SPALB"

Cause:

Effect:

Remedy:

Note:

BM 2221 SPI 2 SPEED NOT ZERO "SSTB"

Cause: Spindle 2: standstill signal +/- monitoring limits missing

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

BM 2222 SPI 2 NO SPEED DETECT "SDTB"

Cause: Spindle 2: No speed detected

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

Page 81: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 81 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2223 SPI 2 SPEED NOT REACHED "SARB"

Cause: Spindle 2: Commanded spindle speed not reached

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

BM 2224 SPI 2 NOT ORIENTED "ORARB"

Cause: Spindle 2: Spindle not orientated (M19)

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

BM 2227 CONFIRMATION MODE ACTIVE

Cause:

Effect:

Remedy:

Note:

BM 2228 FEED OVERRIDE TO 0%

Cause: Feed correction switch is set to 0%

Effect: Axes not moving

Remedy: Set feed correction switch to greater than 0%

Check switch

Note: Message pending. After Q axis move to single movement operating mode

BM 2229 TL-CLAMP MONITOR SWITCHED OFF

Cause: Key switch "Bridge tool clamping device" turned on

Effect: Tool clamping device monitoring is turned off; spindle limited to 150 rpm

Remedy: Turn off "Bridge tool clamping device"

Check "Bridge tool clamping device" switch

Note:

Page 82: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 82 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2230 SPINDLE SPEED LIMIT TO 150 RPM

Cause: Tool clamping device reporting not completely tightened (without tool); the spindle speed is limited to 150/rpm

Effect: Spindle can only turn at max.150 rpm

Remedy: Tool in spindle

Check tool clamping device

Note: See operating instructions

BM 2231 M39 / FEED LIMIT ACTIVE

Cause:

Effect:

Remedy:

Note:

BM 2232 ROB:FUSE TRIPPED

Cause:

Effect:

Remedy:

Note:

BM 2233 ROB:

Cause:

Effect:

Remedy:

Note:

BM 2234 ROB:LOAD DOOR N.OPN "S073/072"

Cause: Robot: Additional switch for Load door is not open

Effect: No enalbe for robot

Remedy: Open load door for robot

Check additional load door switch

Note:

Page 83: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 83 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2235 ROB:

Cause:

Effect:

Remedy:

Note:

BM 2236 ROBOT SAFTY GUARD NOT CLOSED

Cause: Robot: Safty guard around robot is not closed

Effect: SW- Machine will not work in load area

Remedy: Close safty guard

Check safty guard switch

Note:

BM 2237 ROBOT NOT READY

Cause: Robot: Robot is not ready for operation

Effect: Robot signals will not be transmitted

Remedy: See robot authorised personal

Note:

BM 2238 ROB:

Cause:

Effect:

Remedy:

Note:

BM 2239 ROBOT ON: CHECK PART STATUS

Cause: Robot: Robot is new selected

Effect: No enalbe for robot

Remedy: Check part status in SW-Menue

Note:

Page 84: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 84 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2240 ROB: EMPTY OUT MACHINE ACTIVE

Cause: Robot: Empty out machine is selected

Effect: Machine will not proceed with production

Remedy: Turn off selection "Empty Out Machine"

Note:

BM 2241 ROB: P/CHECK L-DOOR OPEN/CLOSE

Cause: Robot: Both limit switches of load door open/close were engaged

Effect: No enalbe for robot

Remedy: Check limit switches for load door open / close

Note:

BM 2242 SPI 3 TOLERANCE BAND "SPALC"

Cause:

Effect:

Remedy:

Note:

BM 2243 SPI 3 SPEED NOT ZERO "SSTC"

Cause: Spindle 3: standstill signal +/- monitoring limits missing

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

BM 2244 SPI 3 NO SPEED DETECT "SDTC"

Cause: Spindle 3: No speed detected

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

Page 85: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 85 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2245 SPI 3 SPEED NOT REACHED "SARC"

Cause: Spindle 3: Commanded spindle speed not reached

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

BM 2246 SPI 3 NOT ORIENTED "ORARC"

Cause: Spindle 3: Spindle not orientated (M19)

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

BM 2250 SPI 4 TOLERANCE BAND "SPALD"

Cause:

Effect:

Remedy:

Note:

BM 2251 SPI 4 SPEED NOT ZERO "SSTD"

Cause: Spindle 4: standstill signal +/- monitoring limits missing

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

BM 2252 SPI 4 NO SPEED DETECT "SDTD"

Cause: Spindle 4: No speed detected

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

Page 86: Fanuc Fault Codes Ba 400

FM/BM 1xxx/2xxx

Version F_02 / 13.08.2008 WeK 86 / 86

T:\Konstruktion\e_konstruktion\sw-hilfen\allgemein\original\Fanuc_BA03_Uk.dot

BM 2253 SPI 4 SPEED NOT REACHED "SARD"

Cause: Spindle 4: Commanded spindle speed not reached

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note:

BM 2254 SPI 4 NOT ORIENTED "ORARD"

Cause: Spindle 4: Spindle not orientated (M19)

Effect: Feed stop

Remedy: Check spindle control

See Fanuc Spindle Manual

Note: