7/29/2019 F200_EN_M

1/16

U S E R M A N U A L

F200 ADSL USB MODEM

7/29/2019 F200_EN_M

2/16

.

7/29/2019 F200_EN_M

3/16

C O N T E N T S

1. Introduction 4

2. Specifications 4

2.1 ADSL Standards supported 4

2.2 Supported Protocols 4

2.3 Connections 5

3. Hardware Installation Procedures 5

3.1 Hardware Requirements 5

3.2 Preparing your network information 5

3.3 Configure the ISP parameters for your Windows XP 6

3.4 Driver Installation on Windows XP 7

3.5 Software Configuration 8

3.6 Connection to the Internet 11

4. Troubleshooting 13

7/29/2019 F200_EN_M

4/16

1. Introduction

F200 ADSL USB modem is a high performance and high-speed device thaprovides a full rate ADSL modem with the superb reliability and is a completesolution for home and office. The F200 ADSL USB modem can have a maxi

mum downstream data rate of up to 8Mbps and an upstream of up to 1MbpsYou can safely enjoy the new generation broadband Internet with the F200ADSL USB modem. Included drivers for Win98/ ME/ 2000/ XP.

2. Specifications

2.1 ADSL Standards supported:Supports ITU-T G.992.1(G.DMT) and ANSI T1.413 Issue 2Supports G.992.2 (G.LITE)Annex A & B

2.2 Supported Protocols:WANPPP over ATM (PPPoA) VC MUXPPP over ATM (PPPoA) with LLC/SNAP

PPP over Ethernet (PPPoE) with LLC/SNAPPPP over Ethernet (PPPoE) with VC MUXLANBridged Ethernet (IP over ATM) with LLC/SNAPBridged Ethernet (IP over ATM) with VC MUXRouted IP over ATM with LLC/SNAPClassical IP over ATM

This package includes:

F200 USB modem1 USB cable1 RJ11 telephone cable1 CD with drivers1 users manual

7/29/2019 F200_EN_M

5/16

2.3 Connections

USB Connects the USB cable from the USB port of the F200 modem to theUSB port of the computer.LINE Connects the RJ11 telephone cable from the telephone line port oF200 modem to the telephone plug..

LED indications:POWER:After successfully installing the modem, the POWER LED light turnson. It will stay on every time you start your computer.

3. Hardware Installation Procedures3.1 Hardware Requirements

The following hardware is necessary to configure and use the F200:RJ-11 (ADSL Ready) telephone LineUSB cable (Included in the package)

3.2 Preparing your network informationTo configure your ADSL modem smoothly, it is required that you contact youISP (Internet Service Provider) and acquire the following information:Type of Mode Encapsulation used:a. PPPoE, PPPoA, IPoA, Bridged or Routed.

DSL connection parameters:b. For PPPoE or PPPoA, refer to Table 3 and fill-in all values (provided by youISP). During the driver installation, select WAN.c.For Bridged, Routed, or IPoA, refer to Table 4 and fill-in all values (provided byyour ISP). During the driver installation, select LAN.

5

7/29/2019 F200_EN_M

6/16

Table 3 WAN (PPPoE/PPPoA parameters)

Information ValuePVC Settings VPI

VCIEncapsulation (LLC VCMux)

Login Username

Information PasswordLine Modulation Automatic ITU G.dmt or G.lite preferred

Automatic ANSI T1.413 i2 preferredITU (G.dmt or G.lite)G.dmt

G.lite

table 4 LAN (Bridged/Routed/IPoA parameters)

Information ValuePVC Settings VPI

VCIEncapsulation (LLC or VC Mux)IP Information IP Address

Subnet MaskGateway IP AddressPreferred DNS address

Alternate DNS address (If available)Line Modulation Automatic ITU G.dmt or G.lite preferred

Automatic ANSI T1.413 i2 preferredITU (G.dmt or G.lite)G.dmt

G.lite

3.3 Configure the ISP parameters for your Windows XPF200 is initially set to function on Annex B protocol (ADSL over ISDN). Toinstall the F200 based on Annex A protocol ( ADSL over PSTN), follow theprocedure below.NOTE: THE FOLLOWING PROCEDURES APPLY FOR PPPoA MODE..

Table 5Annex A

Driver Setup WANProtocol PPPoAEncapsulation VCMUXModulation Automatic ITU G.dmt or G.lite preferredVPI 8VCI 35USERNAME testPASSWORD test_passw

7/29/2019 F200_EN_M

7/16

3.4 Driver Installation on Windows XP

Step 1:Windows will detect the newly installed deviceand the screen below will appear after the

F200 USB ADSL Modem is attached to thesystems USB port.Select "Install from a specific Location",and click "NEXT".

Step 2:Select "Include this location in the search"and type d:\driver\Wan(where D:\ the CD-ROM)Note: If the protocol being used is Bridged,Routed or IpoA, then type d:\driver\Lan

Step 3:Click Continue Anyway.This window appears only on Windows XP.

Installation continues

7

7/29/2019 F200_EN_M

8/16

Step 4:Click "Finish"

Step 5:Left click on 'My Computer' icon andclick on 'Properties_ > _Device Manager'

Double click on Network adapters andcheck to see for:'Crypto F200 USB ADSL WAN adapter'

3.5 Software Configuration

Continue the setup process of the F200.Step 1:Double click onthe Access Runner icon

Step 2:Initially there is no connection / synchronizationwith the ADSL line Attempting to Activate Line.Press ALT P on your keyboard

7/29/2019 F200_EN_M

9/16

Step 3:Here you can see that the connection hasnot been established. Attempting to Activate Line.

Click the Line Setup tab

Step 4:Initially it is set to Annex B (ADSL over ISDN) asshown on the bottom right.

Note: If the line was ISDN, then we do not change it.

Step 5:Select Annex A (ADSL over POTS) (given that the linewas PSTN). Click Apply.Note: Incase you take out the USB plug from your

computer and plug it back to the USB port of thecomputer again (does not matter if its upon shut-downor while the computer is on), then the Annex selectionwill automatically be set to Annex B. To set it backto Annex A, please follow this procedure again.Select the Protocol Setup tab

Step 6:

In theVirtual Path Identifier (VPI) selection, andunderVirtual Circuit 0, the value is 0.and

In theVirtual Circuit Identifier (VCI) selection, andunderVirtual Circuit 0, the value is 35.

9

7/29/2019 F200_EN_M

10/16

Step 7:For the example insert:

VPI = 8

VCI = 35Click Apply.

Step 8:For Encapsulation Mode select the connectionprotocol:

PPP over ATM VCMUX (RFC2364)Click ApplyClick on the General tab

Step 9:Under Line Status, the indication ADSL ConnectionEstablished, indicates that the connection /

synchronization with the ADSL line has been donewith success.Note: 1 to 2 minutes are required after you makethe above configurations, in order for the F200 tobe synchronized with the ADSL line.

Step 10:To see information regarding the connection,click the Physical Layer Statistics tab,and click OK.

7/29/2019 F200_EN_M

11/16

Double click on the Access Runner iconADSL Connection Established indicates that theconnection / synchronization with the ADSL linehas been done with success.

Note:After power on the PC, it takes 1 to 2 minutesin order for the F200 to be synchronizedwith the ADSL line.

3.6 Connection to the Internet

Step 1:To connect to the Internet, double click on theConnect Access Runner DSL icon which is foundon the Desktop

Step 2:Insert the "User Login & Password" that has beengiven to you by your ISP, click Dial to connect.

Step 3:

Double click on the connection icon on the Windows toolbar.

11

7/29/2019 F200_EN_M

12/16

Step 4:To ensure that the F200 has been successfullyinstalled, under the General tab, check to see thatConnected is indicated next to Status.

You can also check your connectionspeed: Speed -> 448.0kbps.

Step 5:Under the Details tab, you can see various

information regarding the connection.(i.e. Server Type, Server IP address etc.).

7/29/2019 F200_EN_M

13/16

4. Troubleshooting

The POWER LED is not onCheck to see that the connections between the USB port of the F200 and the

USB port of your computer are plugged in correctly.

Cannot access ISPIf in PPPoA & PPPoE mode, check your login account and password for the

remote server.Check your VPI/VCI value and encapsulation mode are the same as your ISP

gave you.Try to dial the phone to check if the phone line to CO is good if telephone

service is available.

Note: Incase you take out the USB plug from your computer and plug it backto the USB port of the computer again (does not matter if its upon shut-downor while the computer is on), then the Annex selection will automatically be seto Annex B. To set it back to Annex A, please follow the procedure of Step 5of 3.5 Software Configuration.

Reset (reset connection)Restart the connection of the F200 modem by pressing Stop and Start inthe first window example of section 3.5.Note: Check to see if it is successful or not.

13

7/29/2019 F200_EN_M

14/16

Declaration of Conformity

The 'F200 ADSL USB MODEM' is approved for use for within the EuropeanUnion, and the compatibility of this unit and its basic requirements are declared

with the CE symbol.

Passage extract of the authentic declaration of conformity:

CE Verification of Compliance

Technical Standards:

EMC: ETSI EN 300 386 v1.3.2/2002.12

LVD: EC LOW VOLTAGE DIRECTIVE 73/23/EEC, 93/68/EEC

Measurement standards:

(1) EN 55022 : 1998(2) EN 61000-3-2: 2000(3) EN 61000-3-3: 1995(4) EN 61000-4-2: 1998(5) EN 61000-4-3: 1998(6) EN 61000-4-4: 1995(7) EN 61000-4-5: 1995(8) EN 61000-4-6: 1996(9) EN 61000-4-11: 1994(10) EN 60950 : 2000

Measurement Facilities: BEST LABORATORY CO., LTD.

Note: Specifications are subject to change without prior notice.

7/29/2019 F200_EN_M

15/16

7/29/2019 F200_EN_M

16/16

www.crypto.gr