f-fl/15/40k/kn/bz-87 f-fl/15/50k/kn/bz-87 ... - topaz-usa.com
TRANSCRIPT
WARNING
- DANGER- Risk of shock- Disconnect power before installation.• Electrical connections must be made in accordance with the NEC and all federal and local electrical safety codes.• Suitable for damp or wet locations and in ambient temperature range of -40° through 113°F• Not for use in hazardous environments• Min 167°F supply conductors.• This luminaire is rated for 120-277V, 60Hz only.• Product must be properly grounded to prevent product malfunction and/or electrical shock• Do not install if lens is cracked, or fixture is damaged in any way
- Please Note -• Disconnect power and allow to cool prior to cleaning or maintenance.
1.Loosen the screw used to fix the upper and the lower mount in rotating shaft by Hexagon wrench.
2.Rotate the bracket to properly adjust angle as needed.
3.Lock the upper and lower brackets with Hexagon wrench.
4.Connect wires.
Notice: The maximum diameter of lamp pole is 2.36”,
lamp adjustable angle is 0-90.o
(Slipfitter)
1. Use screw key to open the junction-box. 3.Screw up the knuckle mount into junction-box.
4.Use wire-nuts to connect the wires of lamp and junction-box
2.Put the wires of lamp into the junction-box.
water-proof gasketcover of junction-box
screw
(Kunckle)
Installation Instruction
7.Connect wires
BlackWhite
L
N
Green
(Trunnion/Yoke)
Black
White
L
N
Green
1-10V Dimming
DC (+)
DC (-)
Purple(DIM+)Gray(DIM-)
1-10VDimming
DC(+)
DC(-)
Purple(DIM+)
Gray(DIM-)
BlackWhite
L
N
Green
1-10VDimming
DC(+)
DC(-)
Purple(DIM+)
Gray(DIM-)
(1)
(2)
(3)
knuckle mount
lamp
wires
5. lock the junction-box with screw key 7.Adjust the lamp into suitable angle. 8.Use hex-key to screw up the hex-screw. Installation completed.
6.Use hex-key to screw off the hex-screw in knuckle mount.
hex-key
enlarged detail
The Installation must be carried out by
with
• Before turning on fixture, check to see if fixture was damaged during transportation. DO NOT install or use fixture if there is visible damage.• The products itself and all its components should not be mechanically stressed.• Installation must not damage or destroy conducting paths or other parts of the product.• Installation of LED product (with power supplies) needs to be made about all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations.• Wrong polarity may damage or destroy the LED products.• DO NOT operate LEDs in reverse bias.• Electrical connections should always be in a dry area and adequately sealed.• This product series emits high light output. DO NOT look directly into the light emitting area. Direct exposure to the light over an extended time period may harm eyes.
INSTALLATION - Surface Mounting1. Do not remove any part of the fixture.2. For product specifications, please see the label on fixture.3. Terminal block shall conform to UL standard; and s hall be specified as following: - The type of terminal: screw/screwless - Number of terminals: 3 poles - Rated voltage: Min. 277V
www.topaz-usa.com 925 Waverly Ave • Holtsville, NY 11742 • 800-666-2852 • Fax: 631-758-8026 • ©2019 Topaz Lighting Corp.
LED LOW POWER FLOOD LIGHTSINSTALLATION INSTRUCTIONS
Items: F-FL/15/40K/KN/BZ-87F-FL/30/40K/KN/BZ-87F-FL/50/40K/KN/BZ-87F-FL/50/40K/TR/BZ-87
F-FL/15/50K/KN/BZ-87F-FL/30/50K/KN/BZ-87F-FL/50/50K/KN/BZ-87F-FL/50/50K/TR/BZ-87
Input Voltage Frequency Power Input Current
AC120-277V 50/60Hz 15W 0.138A
AC120-277V 50/60Hz 30W 0.275A
AC120-277V 50/60Hz 50W 0.459A
Installation Instruction
7.Connect wires
BrownBlue
L
N
Yellow
(Trunnion/Yoke)
shown3. Place bracket tightly toward the wall and through the thread.
4. Fasten the screw nut clockwise using provided hardware and wrench.
washer
screws.6. Fasten screws on both sides usings allen key.
allen key
WARNING
- DANGER- Risk of shock- Disconnect power before installation.• Electrical connections must be made in accordance with the NEC and all federal and local electrical safety codes.• Suitable for damp or wet locations and in ambient temperature range of -40° through 113°F• Not for use in hazardous environments• Min 167°F supply conductors.• This luminaire is rated for 120-277V, 60Hz only.• Product must be properly grounded to prevent product malfunction and/or electrical shock• Do not install if lens is cracked, or fixture is damaged in any way
- Please Note -• Disconnect power and allow to cool prior to cleaning or maintenance.
1.Loosen the screw used to fix the upper and the lower mount in rotating shaft by Hexagon wrench.
2.Rotate the bracket to properly adjust angle as needed.
3.Lock the upper and lower brackets with Hexagon wrench.
4.Connect wires.
Notice: The maximum diameter of lamp pole is 2.36”,
lamp adjustable angle is 0-90.o
(Slipfitter)
1. Use screw key to open the junction-box. 3.Screw up the knuckle mount into junction-box.
4.Use wire-nuts to connect the wires of lamp and junction-box
2.Put the wires of lamp into the junction-box.
water-proof gasketcover of junction-box
screw
(Kunckle)
Installation Instruction
7.Connect wires
BlackWhite
L
N
Green
(Trunnion/Yoke)
Black
White
L
N
Green
1-10V Dimming
DC (+)
DC (-)
Purple(DIM+)Gray(DIM-)
1-10VDimming
DC(+)
DC(-)
Purple(DIM+)
Gray(DIM-)
BlackWhite
L
N
Green
1-10VDimming
DC(+)
DC(-)
Purple(DIM+)
Gray(DIM-)
(1)
(2)
(3)
knuckle mount
lamp
wires
5. lock the junction-box with screw key 7.Adjust the lamp into suitable angle. 8.Use hex-key to screw up the hex-screw. Installation completed.
6.Use hex-key to screw off the hex-screw in knuckle mount.
hex-key
enlarged detail
The Installation must be carried out by
with
www.topaz-usa.com 925 Waverly Ave • Holtsville, NY 11742 • 800-666-2852 • Fax: 631-758-8026 • ©2019 Topaz Lighting Corp.
WARNING
- DANGER- Risk of shock- Disconnect power before installation.• Electrical connections must be made in accordance with the NEC and all federal and local electrical safety codes.• Suitable for damp or wet locations and in ambient temperature range of -40° through 113°F• Not for use in hazardous environments• Min 75°C supply conductors.• This luminaire is rated for 120-277VAC, 60Hz only.• Product must be properly grounded to prevent product malfunction and/or electrical shock• Do not install if lens is cracked, or fixture is damaged in any way
- Please Note -• Disconnect power and allow to cool prior to cleaning or maintenance.
1.Loosen the screw used to fix the upper and the lower mount in rotating shaft by Hexagon wrench.
2.Rotate the bracket to properly adjust angle as needed.
3.Lock the upper and lower brackets with Hexagon wrench.
4.Connect wires.
Notice: The maximum diameter of lamp pole is 2.36”,
lamp adjustable angle is 0-90.o
(Slip-fitter)
1. Use screwdriver to open junction-box. 3. Screw the knuckle mount onto junction-box.
4.Use wire-nuts to connect the wires of lamp and junction-box
2. Run wires of lamp into the junction-box.
water-proof gasketcover of junction-box
screw
(Kunckle)
Installation Instruction
7.Connect wires
BlackWhite
L
N
Green
(Trunnion)
Black
White
L
N
Green
1-10V Dimming
DC (+)
DC (-)
Purple(DIM+)Gray(DIM-)
1-10VDimming
DC(+)
DC(-)
Purple(DIM+)
Gray(DIM-)
BlackWhite
L
N
Green
1-10VDimming
DC(+)
DC(-)
Purple(DIM+)
Gray(DIM-)
(1)
(2)
(3)
knuckle mount
lamp
wires
5. Lock the junction-box with screwdriver. 7.Adjust the lamp into suitable angle. 8.Use hex-key to screw up the hex-screw. Installation is complete.
6.Use hex-key to screw off the hex-screw in knuckle mount.
hex-key
enlarged detail
The Installation must be carried out by
with
The dimming function is applicable to 30W and 50W ONLY.
2. Hammer bolts to the pre-drilled holes with the tthreads facing outward
Place
Items: F-FL/15/40K/KN/BZ-87F-FL/30/40K/KN/BZ-87F-FL/50/40K/KN/BZ-87F-FL/50/40K/TR/BZ-87
F-FL/15/50K/KN/BZ-87F-FL/30/50K/KN/BZ-87F-FL/50/50K/KN/BZ-87F-FL/50/50K/TR/BZ-87
Pg 2
Installation for Photocell Sensor
Product Dimensions
3.Install the photocell sensor on the back plate.
PCBboard
+ -
LED D
river
loadNLPCB
board
+ -
LED D
river
red black
grey
purp
le
black
white
greengreen
photoelectricswitch
white
output
input
output
input
red black
2.Select one of the methods in figure 1 or figure 2 to open the integrated knockout for photocell.
greypurple
white
whi
te
1.Remove screws and back plate
4-1.Original wiring 4-2.Wiring with Photocell.
5.Install the back plate, lock the screws and complete the installation.
screw
back plate
L
NL N
blackred
Blac
k
M10 internal hexagonal wrench
Electric drill
purple
grey
black
grey
purple
photocell sensorcushion
screwprotective cap
This step can be omitted ifwith non-dim driver.
This step can be omitted ifwith non-dim driver.
Figure 1
Figure 2
www.topaz-usa.com 925 Waverly Ave • Holtsville, NY 11742 • 800-666-2852 • Fax: 631-758-8026 • ©2019 Topaz Lighting Corp.
Items: F-FL/15/40K/KN/BZ-87F-FL/30/40K/KN/BZ-87F-FL/50/40K/KN/BZ-87F-FL/50/40K/TR/BZ-87
F-FL/15/50K/KN/BZ-87F-FL/30/50K/KN/BZ-87F-FL/50/50K/KN/BZ-87F-FL/50/50K/TR/BZ-87
LED FLOOD LIGHT
Please read the user manual carefully and follow it. This will help to prevent damage of the product, prolong its lifespan;And it will be helpful for your normal use and maintenance, to ensure that your life safety. Please keep the manual properly.
Part No.TS-FL0805-50W-XXX-X-XXK
TS-FL0803-30W-XXX-X-XXK
TS-FL0802-15W-XXX-X-XXK
AC120-277V
AC120-277V
AC120-277V
50/60Hz
50/60Hz
50/60Hz
50W
30W
15W
0.459A
0.275A
0.138A
Input Voltage Frequency Power Rated Current
Safety Instruction● Read instructions carefully before attempting to install fixture. Retain instruction for future reference.● Disconnect power before installing or servicing. This fixture must be wired in accordance with the National Electrical Code and applicable local codes and ordinances.● All wiring should be performed by a qualified electrician. This fixture is for outdoor use and should not be used in areas with limited ventilation or high ambient temperatures.
INSTALLATION-Surface Mounting1.Do not remove any part of the fixture.2.Specification please see the label on fixture.3.Keep enough length wires to ensure adjusting angle unhindered.4.Terminal block to be used shall conform to UL standard; and shall be specified as following: - the type of terminal: screw/screwless; - number of terminals: 3 poles; - rated voltage: Min. 277V; - any fixing method: fixed inside the connecting box.5.LED Flood Light must be operated with in an ambient temperature range of -40oC (-40oF) and 45oC (113oF).
Warning1. Before starting use of the light, please check if the light was damaged during transportation. If any damage shown, pleases DO NOT install or use it.2. The products itself and all its components should not be mechanically stressed.3. Installation must not damage or destroy conducting paths or other parts of the product.4. Installation of LED product (with power supplies)needs to be made with regard to all applicable electrical and safety standards.Only qualified personnel should be allowed to perform installations.5. Correct electrical polarity needs to be observed. Wrong polarity may damage or destroy the LED products.6. All LEDs are static sensitive. Precautions should be taken to ensure that LEDs are well protected from ESD during handing, even though the chips are safe in low static-electric discharge events.7. DO NOT operate LEDs in reverse bias.8. Damaged by corrosion will not be honored as a materials defect claim. It is the user's responsibility to provide suitable protection against corrosive agents such as moisture and condensation and other harmful elements.9. Electrical connection should be in a dry area unless adequately sealed.10. This product series emits high light output. DO NOT look directly into the light emitting area. Direct exposure to the light over an extended time period may harm eyes.11. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
,XXX can be “ 80*110, 60 , 90 ”;
XXK can be any number for color temperature: 40K, 50K, 57K ;
eb nac X:W05-51 ;" eko Y"= YelkcunK"=K"XXX represents the Beam Angle,
F-FL-50W/XXK/XX/XXF-FL-30W/XXK/XX/XXF-FL-15W/XXK/XX/XX
Product Dimension
Part No. A B C D E F G H I J K9.0"7.0"5.1"
8.4"7.2"6.1"
2.2"3.3"3.3"
2.3"2.0"1.8"
9.8"7.8"5.7"
7.7"6.5"4.3"
2.6"2.5"1.5"
0.47"0.47"0.32"
1.77"1.38"0.98"
4.13"3.43"2.4"
0.87"0.87"0.4"
(Trunnion/Yoke)(Knuckle)
I
H
K
J
Installation Instruction
The Installation must be carried out by a qualified electrician.
(Trunnion)
第八代美规泛光灯说明书 规格:297*210材质:80克书纸 单黑双面印刷(对折再对折)品号:
90
The dimming function is applicable to 30W and 50W, 15W is not avaiable.
The dimming function is applicable to 30W and 50W, 15W is not avaiable.
BlackWhite
Green
1-10VDimming
DC(+)
DC(-)
Purple(DIM+)
Gray(DIM-)
Installation for Photocell Sensor
( Photocell is available for 30W to 90W, with photo control function. )
3.Install the photocell sensor on the back plate.
PCBboard
+ -
LED D
river
loadNL
PCBboard
+ -
LED D
river
red black
grey
purp
le
black
white
greengreen
photoelectricswitch
white
output
input
output
input
red black
2.Select one of the methods in figure 1 or figure 2 to open the integrated knockout for photocell.
greypurple
white
whi
te
1.Remove screws and back plate
4-1.Original wiring 4-2.Wiring with Photocell.
5.Install the back plate, lock the screws and complete the installation.
screw
back plate
L
N L N
blackred
Blac
k
M10 internal hexagonal wrenchElectric drill
purplegrey
black
grey
purple
photocell sensorcushionscrewprotective cap
This step can be omitted ifwith non-dim driver.
This step can be omitted ifwith non-dim driver.
Figure 1 Figure 2
Steps: 1.Cut off the original L and N terminals. 2.Strip 10-12mm wire of black and white wire. 3.Connect with terminals according to the left figure.
Ø17mm(Ø0.67’’ hole saw)
Pg 3
LED Driver
LED Driver
LED Driver
LED Driver
LINE(Black Wire)
LINE(Black Wire)
LINE(Black Wire)
LINE(Black Wire)
NEUTRAL(White Wire)
NEUTRAL(White Wire)
NEUTRAL(White Wire)
NEUTRAL(White Wire)
GROUND
GROUND
GROUND
GROUND
120 VOLTS
240VOLTS
240VAC Split PhaseWiring (USA 3 Wire)
208 VOLTS
208V Split PhaseWiring (USA 3 Wire)
277 VOLTS
Hot
Hot1
Hot1
Hot
Neutral
Neutral
Neutral
Neutral
Ground
Hot2
Hot 2
Ground
www.topaz-usa.com 925 Waverly Ave • Holtsville, NY 11742 • 800-666-2852 • Fax: 631-758-8026 • ©2019 Topaz Lighting Corp.
LED LOW POWER FLOOD LIGHTSINSTALLATION INSTRUCTIONS
Pg 4
Items: F-FL/15/40K/KN/BZ-87F-FL/30/40K/KN/BZ-87F-FL/50/40K/KN/BZ-87F-FL/50/40K/TR/BZ-87
F-FL/15/50K/KN/BZ-87F-FL/30/50K/KN/BZ-87F-FL/50/50K/KN/BZ-87F-FL/50/50K/TR/BZ-87