f engine maintenance procedure and record...the fire engine maintenance procedure and record book...
TRANSCRIPT
FIRE ENGINE MAINTENANCEPROCEDURE AND RECORD
LICENSE: __________________________________________
DUTY STATION: _____________________________________
ENGINE IDENTIFICATION NUMBER: ____________________
-2-
i
FIRE ENGINE MAINTENANCE PROCEDURE AND RECORDPREFACE
The Fire Engine Maintenance Procedure and Record book was created by adevelopment group with direction from the National Interagency Fire Center(NIFC) National Fire and Aviation Training Support Group. The primarydevelopers in this effort were:
Al Olson BLM Elden Alexander BLMLarry Sutton BLM Bill Swann BLMKen Shaver BLM Steve Loucks BLMJason Simmons BLM Tim Taggart BLM
The National Fire and Aviation Training Support Group appreciates the efforts ofall contributors to the design and development of this product.
Please consider this first year edition (May 1999) as a dynamic document andmake recommendations accordingly. Suggestions for improvements or changesare welcome. You may use the evaluation sheet attached with the document.
Please forward questions, comments, or corrections to
Paul Hefner3833 S. Development WayBoise, ID 83705Lotus Notes address: [email protected]
Or to the:
National Interagency Fire CenterNational Fire and Aviation Training Support GroupAttn: BLM Training3833 South Development WayBoise, Idaho 83705
ii
iii
FIRE ENGINE MAINTENANCE PROCEDURE AND RECORDCOMMENT FORM
Name/Office:
Page Number/Section Comments Relate to:
Subject:
Comments:
iv
v
TABLE OF CONTENTS
How To Use the Fire Engine Maintenance Procedure and Record . . . . . . . . . . vii
I. Fire Engine and Pump Package Data . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
II. Fire Engine Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
III. Radio Installation and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
IV. Inspection and Service Intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
V. Daily Fire Engine Inspection Instructions . . . . . . . . . . . . . . . . . . . . . . . . 5
VI. Periodic/Post Fire Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
VII. Pump Maintenance Service Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 9
VIII. 3000 Mile Service Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
IX. Annual Service Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
X. Winterization Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Appendices
Appendix A: Fire Engine Preventative Maintenance Checklist . . . . . . . . . A-1
Appendix B: Form 1520-35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Appendix C: Winterization Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Appendix D: Pump Test Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Appendix E: Repair Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
Appendix F: Engine Service Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1
vi
vii
How To Use the Fire Engine Maintenance Procedure and Record Book
This book has been developed for you to use as a guide to perform routinemaintenance on a BLM fire engine. Duties described as “daily,” or “as needed” arerecommendations by the development group. However, if local protocol dictatesthat some tasks are done more often, or less, then local standards should befollowed. This document is to be used for both the “Heavy” and “Light” engines;some instructions are specific to each type individually. Skip the task if it does notpertain to the engine you are using.
The appendices located in this book are to be used solely as a reference document. Additional copies of the documents to be used in the field can be obtained at theB.L.M. training web page or make copies of the ones provided.
Line number on the Daily Fire Engine Inspection Checklist (Appendix A)corresponds with line number in the Fire Engine Preventative Maintenance DailyInspection Instructions. Use the instructions as a guide for your Daily Inspection.
The Pump Test Record is included in this guide to provide you an area todocument pump performance and trend. There are various methods used in thetesting of pump performance, whichever method is used should be consistent anddone on a routine basis. The development group does recommend the followingpump test:
Using the 1 ½ overboard discharge nearest to the pump, assemble a 3/4 inch,3/8 diameter nozzle tip (NFES 0638) on the 1 ½ discharge. You will need touse the appropriate reducers to do this. With the valve to the 1 ½ dischargeopen, throttle the pump to max P.S.I. output. Record the P.S.I. gaugereading in the Pump Test Log. To record maximum (max) pump G.P.M.refer test results to the Water Equipment Handling Guide (Fourth Edition),Appendix 2 (Nozzle Flow Rates.) This test will track pump trend. Anydecline in pump P.S.I. output will alert the operator of potential pumpproblems and/or unacceptable G.P.M. output. The development groupselected this test for ease of performing and availability of testing equipment.
viii
1
I. FIRE ENGINE AND PUMP PACKAGE DATA
This section needs to be filled out and kept current for the life of the engine. This information is needed by mechanics and engine module members whenrepairing or servicing the engine.
VEHICLE DATA
License__________Eng__________Make__________ Model_______
Year_________Serial No._____________________________________
Eng: Mfr/Model___________Crankcase Cap. Qts.________Wt.______
Coolant Cap. Qts._______Water Filter______Air Filter(Primary)______
Air Filter(Secondary)________ Fuel Filter(Primary)_______________
Fuel Filter(Secondary)_______ Oil Filter_______ Battery Group____
Tire Size__________ Ply Rating_________ Pressure__________
Fan Belts__________ P/S Belt__________ Alternator Belt_____
Air Comp. Belt__________Other belts_________________________
Transmission Type___________________Serial No.______________
Diff. Type and Ratio_______________________________________
Buildup Mfg.___________________Date Placed In Service_________
PUMP PACKAGE DATA
Pump Make____________________ Model________________
Rating____________________ GPM @ 150 PSI
Pump Engine Mfg.______________________ Model_______________
2
Crankcase Cap. Qts._________ Wt._________ Oil Filter__________
Air Filter__________ Fan Belts_________ Coolant Cap. Qts._____
Foam Equipment Make __________________ Model_____________
FIRE ENGINE DIMENSIONS
Length__________ Width__________ Height__________
MISCELLANEOUS ENGINE INFORMATION
3
II. FIRE ENGINE WEIGHTS
This section needs to be filled out and kept current for the life of the engine. This information is needed, to keep engines at the proper GVW ratings, forTransport (low-boy) operations, or for towing operations.
FIRE ENGINE WEIGHT (GVW)
Manufactures Front Axle Rear Axle TotalRecommendations
FIRE EQUIPPED ENGINE WEIGHT (GVW)
Front Axle Rear Axle Total Date
4
III. RADIO INSTALLATION AND PREVENTATIVE MAINTENANCE
Inspect after installation and at the Annual Inspection.Radio unit should be turned off before mechanical inspection is started.
A. TRANSMITTER-RECEIVER (T/R) CHASSIS MOUNTING AREA
1. Tighten loose mounting hardware.2. Check that the T/R unit is locked into the housing.3. Check that the cable connector is firmly inserted into the T/R
unit connector.4. Check that the antenna cable connector is finger tight.5. Check to see that there is free space around the T/R chassis for
ventilation.
B. ANTENNA
1. Check that the whip is firmly secured.2. Check that the base is firmly mounted.3. If visible, check the cable connections to the base for
cleanliness and tightness.
C. CONTROL HEAD/SPEAKER
1. Tighten loose mounting hardware.2. Check that the cables are routed and secured under the dash in
a manner which prevents the operators feet from entanglementwith the wires.
3. Check for missing or damaged knobs and switches.4. Switches should operate smoothly without jamming.
D. MICROPHONE
1. Check for frayed cable.2. Push-to-talk button should operate smoothly.3. Microphone hanger should be firmly mounted.
5
E. UNDER THE HOOD
1. Check that the wires are protected from exhaust manifold, sharpedges, and moving parts.
2. Check connections for cleanliness and tightness.3. Wires passing through the fire wall should be protected from
fraying by a grommet in the hole.4. Battery connections should be clean and tight.5. Check condition of fuses and holders.
IV. INSPECTION AND SERVICE INTERVALS
A system of complete service and inspections covering all operatingcomponents of the Fire Engine provides the basic preventative maintenancetool. These inspections and corrective actions are designed for anemergency fleet where use dictates maintenance levels at a much higherdegree than conventional oil change and lubrication intervals.
A. DAILY FIRE ENGINE INSPECTION
1. Periodic/Post Fire
2. Pump Maintenance
B. 3000 MILE SERVICE
C. ANNUAL SERVICE
D. WINTERIZATION
V. DAILY FIRE ENGINE INSPECTION INSTRUCTIONSThis list of instructions corresponds with the Daily Fire Engine InspectionChecklist found in Appendix A. Use this list as a guide during inspections.
1. Oil - Check fluid levels and add if needed.
2. Coolant - Check fluid levels and add if needed.
3. Power Steering - Check fluid levels and add if needed.
6
4. Automatic Transmission Fluid - Check transmission fluid according tomanufacturer’s guidelines.
5. Fan Belts - Check belts for wear, frays, tension, or cracks.
6. Air Cleaners - Carefully inspect mounting brackets, inlet hoseconnections, and fittings. Inspect gasket and sealing surface areas. Replace service element, if needed.
7. Hoses - Check for signs of wear, cracks or leaks. Check clamps.
8. Leaks - Check for signs of dripping fluids around major componentsof the Fire Engine.
9. Batteries - Check that battery (s) is secure, connections are tight, cellcaps are present. Battery connections should not be excessivelycorroded. Battery box and cover must be secure.
10. Fuel Tank - Make sure it is full and securely mounted.
11. Hydraulic Oil (if applicable) - Check level of fluid ; add if needed.
12. Air Tanks - Check for moisture and bleed if necessary. Inspectmounting brackets.
13. Slack Adjusters - Inspect for excessive play in the brake assembly(adjust to manufacturer’s specifications). Check for broken, loose ormissing parts.
14. Parking Brake - Check for proper operation; ensure vehicle doesn’tmove when brake is set.
15. Air Brake Check - Performed in accordance with D.O.T. (CDL)standards.
16. Tires - Check tread depth and wear, sidewall damage, and tirepressure. Ensure that tires are matched. Check spare. Checkcondition of mud flaps.
7
17. Hubs and Lug Nuts - Check for leaks and proper operation of manualhubs. Inspect rims for damage and proper mounting. Ensure lug nutsare present and tight.
18. Undercarriage - Check for loose bolts, hanging wires, exhaust system,leaks, broken parts, steering components, drive train, shock absorber,free of debris, springs and spring shackles, body mounts, crossmembers, etc.
19. Cabinet Locks - Check for operation.
20. General Condition - Clean and orderly appearance (both internal andexternal). Agency emblems, decals, equipment numbers and licenseplates present and in good condition.
21. Start Engine - Leave engine running for electrical checks.
22. Lights/Signals - Check headlights, brake lights, running lights,emergency lights, turn signals, back-up lights, work lights, panel lights,cabinet lights, dome and dash lights, etc. and replace bulbs asnecessary.
23. Mirrors/Glass - Check for cleanliness, cracks, chips, and damagedbrackets or mounts. Ensure proper adjustment.
24. Back-up Alarm - Operational.
25. Gauges - All gauges should be operational. Any non-functioninggauges should be reported.
26. 2-Way Radio/P.A. - Perform a radio check to see if radio receives andtransmits. Check to see if it is securely mounted and speakers arefunctional.
27. Wipers/Washers - Check condition, reservoir level, and operation.
28. Horn - Check operation, mounting brackets, and air horn.
29. Seat Belts - Clean, secure, accessible, and operational.
8
30. Heater & AC - Check fan, defroster, vents, and controls.
31. Log Book - Current, neat and available. Check for credit card,receipts and proper charge codes.
32. Accident Forms - Contained within the DI-135:DI-134, SF-91, SF-94,CA-1, OF-26 and the S-43. Ensure all forms are in the DI-135.
33. Fire Extinguisher - Securely mounted, pins in place, inspection current, tagged, reflective marker on the extinguisher, and charged.
34. First Aid Kit(s) - Maintained, updated, and clearly marked.
35. Reflector Set - Available and operational.
36. Wheel Chocks - In place and accessible.
37. Jack/Lug Wrench - Compatible with vehicle and proper sized jack.
38. N.U.S - Check for missing or damaged items, replace if necessary.
VI. PERIODIC/POST FIRE SERVICE INSTRUCTIONS
This list of instructions corresponds with the Daily Fire Engine InspectionChecklist found in Appendix A. Use this list as a guide during inspections.
CAB & CHASSIS
1. Differential Oil Level - Full of proper weight lubricant. Plugs are tight.
2. Transfer Case Oil Level - Full of proper weight lubricant. Plugs aretight.
3. Check Drive Lines - Check for damage and wear.
4. Manual Transmission Fluid - Full of proper weight lubricant. Plugsare tight.
9
5. Check N.U.S. - All items specified as minimums in “Standards for FireOperations” are on board, clean and functional.
PUMP PACKAGE
1. Change Oil and Filter - Per manufacturer’s specs or local standards (ifmore stringent.)
2. Check Pump Motor Mounts - Secure and in place.
3. Check Water Tank Mounts - Secure and in place.
4. Check Spark Plugs - Electrode and proper gap; clean; replace asneeded.
5. Fuel Filter - Inspect; replace as needed.
6. Inspect Drive Belts - Examine for wear, frays or cracks; ensure propertension.
7. Air Cleaner - Clean or change as needed.
8. General Appearance - Clean Pump Package; cooling fins clean.
9. Pump Performance Test - Perform pump pressure and flow test atdischarge nearest to pump; record results.
10. Lubricate Pump Head - Per manufacturer’s specs or local standards(if more stringent.)
11. Foam Proportioner - Check operation, follow manufacturersguidelines for flushing and maintenance. Refill with foam if needed.
VII. PUMP MAINTENANCE SERVICE INSTRUCTIONS
This list of instructions corresponds with the Daily Fire Engine InspectionChecklist found in Appendix A. Use this list as a guide during inspections.
10
DAILY:
1. Check oil levels; add if needed.
2. Inspect primary and secondary air filters; clean or replace as needed.
3. Inspect and lubricate throttle and choke cables.
4. All gauges operational; panel lights working.
5. Pressure shutdown switch operational.
6. Fuel tank full; Check for debris and rust.
7. All valves operational.
8. Coolant levels correct.
AS NEEDED:
1. Lubricate pump head and hose reel per manufacturer’s specifications.
2. Lubricate valve controls.
POST-FIRE: (Conduct daily check plus items below)
1. Flush foam system.
2. Refill foam system.
3. Examine strainer; clean if needed.
4. Fill fuel tank.
5. Clean pump package thoroughly.
MONTHLY:
1. Change oil and filter per manufacturer’s specifications.
2. Inspect spark plugs; replace as needed.
3. Inspect fuel filter; replace as needed.
4. Inspect drive belt; replace as needed (for belt-driven models.)
5. Clean/replace air filter.
6. Clean unit thoroughly, i.e., fan housing, etc.
7. Conduct pump performance test (flow test and/or pressure test.)
11
VIII. 3,000 MILE SERVICEIt is highly recommended that service intervals be reduced as conditionswarrant (post-fire, severe conditions, etc.)
A. OIL CHANGE
Drain main engine, auxiliary engine, and pump gear boxes which useoil. Fill crankcases and gear boxes with correct type and grade of oil. Capacities are noted on the Fire Engine Data page. Oil changes shouldbe made when the engine is warm.
B. OIL FILTER
Canister Type: Drain canister, remove dirty filter cartridge and discard,thoroughly clean canister. Install new filter cartridge, install new covergasket (lubricate gasket surface lightly), examine carefully for leakswith engine running. Add oil if necessary.
Spin-On Type: Remove spin-on type filter assembly and discard. Thoroughly clean filter base. Install new filter assembly afterlubricating gasket surface lightly. Examine carefully for leaks withengine running. Add oil if necessary. Do not over-tighten spin-ontype oil filters.
C. LUBRICATION
Lubricate entire chassis. Check oil level in all transmissions, transfercases, differentials, steering gear boxes, hydraulic tanks and pumpprimer reservoir. Lubricate door locks, striker plates, hinges, engineaccessories, fire pump and pump engine accessories. Check pumpgear boxes and electric two-speed axles. Before lubricating front axle,raise front of vehicle off the ground. Do not lubricate front axlesteering knuckles on four-wheel drive vehicles.
D. AIR CLEANER
Carefully inspect mounting brackets, inlet hose connections, andfittings. Inspect gasket and sealing surface areas. Clean or replaceservice element.
12
E. FUEL SYSTEM
Service water separator as per manufacturers recommendations. Change fuel filters annually or more often under severe conditions.
IX. ANNUAL SERVICE (Refer to Appendix B for Form 1520-35)
A. PRE-INSPECTION ROAD TEST
This should include driving the vehicle, foot brake, parking brake,steering, starter, transmission, clutch, gauges noises.
B. WHEEL BEARINGS AND HUBS
Clean, inspect, and re-pack wheel bearings and hubs. Check wheel seals for leaks or damage. Perform at intervals recommended by themanufacturer or more often under severe conditions.
C. AXLES AND DIFFERENTIALS
Drain and refill with correct lubricants to the proper level. Visuallycheck ring gears, pinion gear, and differential side gears.
D. TRANSFER CASE AND TRANSMISSION
Drain and refill with correct lubricant to proper level. Inspect mountsand seals.
Manual Transmission and Transfer Case - remove inspection plates;visually inspect gears and bearings. Inspect and adjust clutch asneeded.
Automatic Transmission - Remove pan, inspect transmission, andservice all filters.
E. DRIVE LINES AND U-JOINTS
Clean, inspect, lubricate, balance or replace as per manufacturer’srecommendations or as severity of conditions dictate.
13
F. STEERING COMPONENTS
Inspect steering gear box, steering components, lubricate and replaceseals as needed.
G. BRAKES
Examine brake lining and drums, pads and rotors, wheel cylinders,master cylinder, brake booster, Accumulock (where applicable),examine brake compressor, mounts, air lines, parking brake cable, andparking brake lining. Inspect “S” cam, shaft, and bushings for wear,inspect wedge assemblies and airbrake chambers and repair asrequired. Inspect all brake components and repair as required. Adjustall brakes.
H. ENGINE TUNE-UP
Check emission control systems and repair as required to bring thevehicle into compliance. Major engine tune-up to be performed asseverity of conditions dictate or as per the manufacturer’s preventativemaintenance recommendations. Check fuel delivery systems; clean,overhaul or adjust as required. Replace fuel filters and water separatorfilter annually or more often under severe conditions. Check turbo-charger.
I. COOLING SYSTEM
Examine radiator, hose connections, coolant recovery tank and waterpump for leaks. Check fan belt for wear and adjustment. Cleanradiator core (external) if dirty. Examine radiator pressure cap. Checkcondition of coolant. Examine automatic transmission heat exchangeroil lines for leaks or damage. Change coolant filter, if applicable.
Coolant must be changed and flushed every two years. If engineoverhauled, radiator shall be removed and completelyoverhauled.
14
J. FRAME AND SUSPENSIONVisually inspect fire package mounting brackets, springs, mounts,shocks, hangers and replace as needed. Perform four-wheelalignment.
K. EXHAUST SYSTEM
Check and inspect exhaust system.
L. AIR CONDITIONING SYSTEM
Inspect and recharge as necessary.
M. POST-VEHICLE INSPECTION ROAD TEST
Additional services may be necessary according to operator’s manual
X. WINTERIZATION INSTRUCTIONS (Refer to Appendix C forWinterization Checklist)
Winterization process should be followed any time the Fire Engine isexposed to freezing temperatures. During short periods of exposure tofreezing conditions a full winterization need not be completed, however someprecautions need to be taken to prevent damage to the pump and plumbing.Full winterization is for periods of prolonged exposure.
A-1
APPENDIX A
A-2
A-3
Department of the Interior • Bureau of Land Management
ENGINE #:
DAILY FIRE ENGINE INSPECTION CHECKLIST
DATE
MILEAGE
Cab & Chassis
1. Oil
2. Coolant
3. Power Steering
4. Automatic Transmission Fluid
5. Fan Belts
6. Air Cleaners
7. Hoses
8. Leaks
9. Batteries
10. Fuel Tank Full
11. Hydraulic Oil
12. Air Tanks
13. Slack Adjusters
14. Parking Brake
15. Air Brake Check
16. Tires
17. Hubs/Lug Nuts
18. Undercarriage
19. Cabinet Locks
20. General Condition
21. Start Engine
Remarks
A-4
22. Lights/Signals
23. Mirrors/Glass
24. Back-up Alarm
25. Gauges
26. 2-Way Radio/P.A.
27. Wipers/ Washers
28. Horn
29. Seat Belts
30. Heater/AC
31. Log Book
32. Accident Forms
33. Fire Extinguisher
34. First Aid Kit
35. Reflector Set
36. Wheel Chocks
37. Jack/Lug Wrench
38. N.U.S.
Pump Package
1. Water Tank Full
2. Valves
3. Coolant
4. Oil Level
5. Fuel Tank Full
6. Air Cleaners
7. 5 Minute Warmup
8. All Gauges
9. Override Switch
10. Live Reels
11. Primer
12. Foam Proportioner
Remarks
A-5
Periodic/Post-Fire
Cab/Chassis
1. Differential Oil Level
2. Transfer Case Oil Level
3. Check Drive Lines
4. Slack Adjusters
5. Parking Brake
6. Air Brake Check
7. Manual Transmission Fluid
8. Check N.U.S.
Pump Package
1. Check Service Log for oil and filter
2. Check Pump Motor Mounts
3. Check Water Tank Mounts
4. Check Spark Plugs
5. Fuel Filter
6. Inspect Drive Belts
7. Clean/ Change Air Filter
8. General Appearance
9. Pump Performance Test
10. Lubricate Pump Head
11. Foam Proportioner
Remarks
A-6
B-1
APPENDIX B
B-2
B-3
B-4
C-1
APPENDIX C
C-2
C-3
Winterization ChecklistDrain all pumps, valves, plumbing, foam unit and water tank. Blow out system withcompressed air and/or add a small amount of antifreeze and water to low spots.
Date: Completed By:REMARKS AREA
PUMP AND MOTOR
Oil Changed Wash Motor
Drain Pump Change Air Filter
Grease Pump Drain Strainer
Add Gas Additive Open Valves(or remove)
Drain Plumbing
FOAM UNIT OR SYSTEM
Flush System Drain All Lines
Drain Metering Valve Drain Selector Valve
Winterize Bladder Inspect “O” Rings
HOSE REELS
Drain Hose Drain Reels
Remove Nozzles Inspect & Lube Gaskets
TANK
Drain & Flush Remove Plugs
ENGINE
Tighten All Bolts Test Anti-Freeze (-40)
Inspect All Lights Post Anti-Freeze DegreeReading on Left Headlight
Brake Fluid Fuel Filter
Anti-Freeze in Wiper Fluid Check or Change Oil
Oil Filter (if oil changed) Auto Transmission Fluid
Clean Radiator Clean or Replace Air Filter
Power Steering Fluid Inspect Fan Belts
AM/FM Radio Off 2-Way Radio Off
AC & Heater Off Battery Off
C-4
UNDER CARRIAGE
Transfer Case Fluid Front Differential Fluid
Rear Differential Fluid Check and Note any Leaks
Grease all Zerks Inspect Tie Rods
Inspect Drive Lines Inspect Springs & Hangers
Inspect Break Pods Drain Air Tanks
Tire Condition (circle)Poor Fair Good
Pump Package MountingBrackets
BOXES
Clean, Paint & sharpenHand Tools
Clean and/or Paint Interiorof Boxes
Clean Fuel Cans & DripTorches
Fire Extinguisher Serviced& Stored
Lock Boxes
D-1
APPENDIX D
D-2
D-3
PUMP TEST RECORDUse this form to document all pump tests.
Date PumpHours
MaxP.S.I.
MaxG.P.M.
Operator Remarks
D-4
E-1
APPENDIX E
E-2
E-3
REPAIR RECORDUse this section as an informal local repair record to document any minor repairsor preventative maintenance completed.
Date Mileage Remarks
E-4
F-1
APPENDIX F
F-2
F-3
'' Engine Service Log Engine Service Log ''''EngineEngine • • • • Date:______________ Mileage:______________
Completed by:______________ Oil Oil Filter Air Filter Fuel Filter
Next Service Due:___________ GG GG GG GG
'' Pump Pump • • • • Date:______________ Mileage:______________
Completed by:______________ Oil Oil Filter Air Filter Fuel Filter
Next Service Due:___________ GG GG GG GG
''EngineEngine • • • • Date:______________ Mileage:______________
Completed by:______________ Oil Oil Filter Air Filter Fuel Filter
Next Service Due:___________ GG GG GG GG
'' Pump Pump • • • • Date:______________ Mileage:______________
Completed by:______________ Oil Oil Filter Air Filter Fuel Filter
Next Service Due:___________ GG GG GG GG
''EngineEngine • • • • Date:______________ Mileage:______________
Completed by:______________ Oil Oil Filter Air Filter Fuel Filter
Next Service Due:___________ GG GG GG GG
'' Pump Pump • • • • Date:______________ Mileage:______________
Completed by:______________ Oil Oil Filter Air Filter Fuel Filter
Next Service Due:___________ GG GG GG GG
F-4
'' Engine Service Log Engine Service Log ''
''EngineEngine • • • • Date:______________ Mileage:______________
Completed by:______________ Oil Oil Filter Air Filter Fuel Filter
Next Service Due:___________ GG GG GG GG
'' Pump Pump • • • • Date:______________ Mileage:______________
Completed by:______________ Oil Oil Filter Air Filter Fuel Filter
Next Service Due:___________ GG GG GG GG
''EngineEngine • • • • Date:______________ Mileage:______________
Completed by:______________ Oil Oil Filter Air Filter Fuel Filter
Next Service Due:___________ GG GG GG GG
'' Pump Pump • • • • Date:______________ Mileage:______________
Completed by:______________ Oil Oil Filter Air Filter Fuel Filter
Next Service Due:___________ GG GG GG GG
''EngineEngine • • • • Date:______________ Mileage:______________
Completed by:______________ Oil Oil Filter Air Filter Fuel Filter
Next Service Due:___________ GG GG GG GG
'' Pump Pump • • • • Date:______________ Mileage:______________
Completed by:______________ Oil Oil Filter Air Filter Fuel Filter
Next Service Due:___________ GG GG GG GG
NOTES