explanation your performanceuse dhcp for dns server information in configure an alternate ip...

Not PassedPass Status:Elapsed Time: 15 seconds Required Score: 100%

Lab Report: 6.2.6 Select and Install a Network Adapter

Your Performance

Your Score: 0 of 3 (0%)

Task Summary

Actions you were required to perform:In Install the 1000BaseTX network adapter in the Support workstation

In Connect the new NIC to the network using a Cat6a cable

In Verify that the Support workstation can communicate with the internet using the new NIC

ExplanationIn this lab, your task is to complete the following on the Support workstation:

Select and install the network interface card with the fastest speed to connect to the local network.Select and install the corresponding cable and connect the computer to the local area network.In Network & Internet settings, confirm that the workstation is connected to the local network and the internet.

Complete this lab as follows:

1. Above the computer, select Motherboard to switch to the motherboard view of the computer.2. On the Shelf, expand Network Adapters.3. Drag the 1000BaseTX network adapter to a free PCIe slot on the computer.

4. Connect the computer to the network as follows:a. Above the computer, select Back to switch to the back view of the computer.b. On the Shelf, expand Cables.c. Select Cat6a Cable.d. In the Selected Component window, drag a connector to the NIC port on the 1000BaseTX network

adapter.e. In the Selected Component window, drag the other connector to the Ethernet port on the wall outlet.

5. Confirm that the computer is connected to the local network and the internet as follows:a. Above the computer, select Front to switch to the front view of the computer.b. Click the power button on the computer case to turn the computer on.c. After the operating system loads, right-click the Network icon and select Open Network & Internet

settings.The Status window shows an active connection to the network and the internet.


Lab Report: 6.6.5 Configure TCP/IP Settings

Your Performance


Task Summary

Actions you were required to perform:In Configure settings for Local Area ConnectionHide Details

Use 192.168.0.254 for the IP address

Use 255.255.255.0 for the subnet mask

Use 192.168.0.5 for the default gateway

Use 163.128.80.93 or 163.128.78.93 for the DNS server

In Configure settings for Local Area Connection 2Hide Details



Do not configure a default gateway address

Do not configure a DNS server address

ExplanationIn this lab, your task is to complete the following:

Configure the IP version 4 TCP/IP settings for the network connections using the settings in the table below.Use the Network & Internet settings in Windows to confirm that the workstation is properly connected to the localnetwork and the internet.

Connection IP Address Subnet Mask DefaultGateway DNS Server

Local AreaConnection 192.168.0.254 255.255.255.0 192.168.0.5 163.128.80.93 or

163.128.78.93

Local AreaConnection 2 10.0.255.254 255.255.0.0 None None


1. In the notification area, right-click the Network icon and select Open Network & Internet settings.2. Select Change adapter options to configure the Local Area Connection adapter.3. Right-click Local Area Connection and select Properties.4. Select Internet Protocol Version 4 (TCP/IPv4).5. Select Properties.6. Select Use the following IP address.7. In the IP address field, enter the IP address.8. In the Subnet mask field, enter the subnet address.9. In the Default gateway field, enter the default gateway address.

10. In the Preferred DNS server field, enter the DNS server address.11. Select OK.12. Click Close.13. Right-click Local Area Connection 2 and select Properties to configure the other network adapter.14. Repeat steps 4–12 to modify the TCP/IP settings for the other network adapter.


Lab Report: 6.6.6 Configure Alternate TCP/IP Settings

Your Performance


Task Summary

Actions you were required to perform:In Configure the wireless network connection to use DHCPHide Details

Use DHCP for addressing information

Use DHCP for DNS server information

In Configure an alternate IP configurationHide Details

Configure an alternate configuration



Use 192.168.2.254 for the default gateway

Use 192.168.2.254 for the preferred DNS server


Record the laptop's static IP and DNS configuration settings.Configure the laptop to obtain IP and DNS addresses automatically.Create an alternate TCP/IP connection with the static settings.


1. In the notification area, select the Network icon and select Open Network & Internet Settings.2. Record the laptop's static IP and DNS configuration settings as follows:

a. Select Change adapter options.b. Right-click Wi-Fi and select Properties.c. Select Internet Protocol Version 4 (TCP/IPv4).d. Select Properties.e. On a piece of paper, record the values for the IP address, subnet mask, default gateway, and DNS server

address.3. Configure the laptop to obtain IP and DNS addresses automatically as follows:

a. Select Obtain an IP address automatically.b. Select Obtain DNS server address automatically.

4. Create an alternate TCP/IP connection as follows:a. Select the Alternate Configuration tab.b. Select User configured.c. In the IP address field, enter 192.168.2.13.d. In the Subnet mask field, enter 255.255.255.0.e. In the Default gateway field, enter 192.168.2.254.f. In the Preferred DNS server field, enter 192.168.2.254.g. Click OK.h. Click Close.


Lab Report: 6.8.3 Configure a Cable Internet Connection

Your Performance


Task Summary

Actions you were required to perform:In Connect the cable modem to the internet using coaxial cable

In Connect the computer to the cable modem using the Ethernet cable

In Plug in the cable modem

ExplanationIn this lab, your task is to connect the components to make the internet connection as follows:

Add the cable modem to the Workspace.Connect the modem to the WAN connection.Connect the computer to the cable modem.Plug in the modem.


1. Add the cable modem to the Workspace as follows:a. On the Shelf, expand Routers.b. Drag the cable modem from the Shelf to the Workspace.

2. Connect the modem to the WAN connection as follows:a. Above the cable modem, select Back to switch to the back view of the cable modem.b. On the Shelf, expand Cables.c. Select the Coaxial Cable.d. In the Selected Component window, drag a connector to the port on the cable modem.e. In the Selected Component window, drag the other connector to the port on the wall plate.

3. Connect the computer to the cable modem as follows:a. Above the computer, select Back to switch to the back view of the computer.b. On the Shelf, select the Cat6a Cable.c. In the Selected Component window, drag a connector to the cable modem's RJ45 port.d. In the Selected Component window, drag the other connector to the network port on the computer.

4. Plug in the cable modem as follows:a. Select the power adapter on the Shelf.b. In the Selected Component window, drag the DC power connector to the port on the cable modem.c. In the Selected Component window, drag the AC adapter connector to the power outlet.


Lab Report: 6.8.4 Configure a DSL Internet Connection

Your Performance


Task Summary

Actions you were required to perform:In Install the DSL routerHide Details

Move the router to the Bench

Connect the power supply

Connect the router to the phone jack on the wall

In Connect the computer to the DSL router

In Add a filter to the phone line (connected to wall)

ExplanationIn this lab, your task is to connect the devices to create a DSL connection as follows:

Install a DSL router. Plug in the router using the power cord on the Shelf.Connect the computer to the network so it can access the internet through the DSL connection.Disconnect the phone and install a DSL filter between the phone and the phone port on the wall outlet.


1. Install a DSL router as follows:a. On the Shelf, expand Routers.b. Drag the DSL router to the Workspace area.c. Above the router, select Back to switch to the back view of the router.d. On the Shelf, expand Cables.e. Select the UTP cable with RJ11 connectors.f. Under Selected Component, drag a connector to the RJ11 port on the router.g. Under Selected Component, drag the other connector to the phone port on the wall outlets.h. On the Shelf, select the Power Adapter.i. Under Selected Component, drag the DC power connector to the port on the DSL router.j. Under Selected Component, drag the AC power plug to a plug on the wall outlets.

2. Connect the computer to the DSL router as follows:a. Above the computer, select Back to switch to the back view of the computer.b. On the Shelf, select the Cat6a cable.c. Under Selected Component, drag a connector to the network port on the computer.d. Under Selected Component, drag the other connector to a network port on the DSL router.

3. Install a filter between the phone port and the phone as follows:a. Above the phone, select Back to switch to the back view of the phone.b. On the Shelf, expand Filters.c. Select the DSL Filter.d. Under Selected Component, drag the connector to the phone port on the wall outlet.e. On the Shelf, expand Cables.f. Select the UTP cable with RJ11 connectors.g. Under Selected Component, drag a connector to the RJ11 port on the filter.h. Under Selected Component, drag the other connector to the phone.


Lab Report: 6.8.6 Configure a Dial-up Internet Connection

Your Performance


Task Summary

Actions you were required to perform:In Configure the dial-up phone number

In Use Dial-up My Work as the destination name

In Allow other users to use the connection

In Use ITS49 as the username

In Use ab18$ut as the password

In Configure the connection to remember the password

ExplanationIn this lab, your task is to configure a dial-up connection to a workplace with the following settings:

Telephone Number: 801-555-4321Destination name (connection name): Dial-up My WorkAllow other users to use the connectionUsername: ITS49Password: ab18$utRemember this password: Enabled


1. In the notification area, right-click the Network icon and select Open Network & Internet settings.2. Maximize the window for easier viewing.3. Select Network and Sharing Center.4. Select Set up a new connection or network to create the dial-up connection.5. Select Connect to a workplace.6. Click Next.7. Select Dial directly.8. In the Telephone number field, enter 801-555-4321.9. In the Destination name field, enter Dial-up My Work.

10. Select Allow other people to use this connection.11. Click Next.12. In the User name field, enter ITS49 as the username.13. In the Password field, enter ab18$ut as the password.14. Select Remember this password.15. Click Next.16. Click Close.

TestOut PC Pro English 6.0.4 ActionsActions

Copyright © 2019Copyright © 2019 TestOut CorporationTestOut Corporation All rights reserved.All rights reserved.

6.9.3 Explore Configuration Information 16.9.3 Explore Configuration Information 1

View LabView LabThis question includes a lab to help you answer the question.This question includes a lab to help you answer the question.

Click the Click the View Lab View Lab button and use the lab interface to find the answers to the following questions.button and use the lab interface to find the answers to the following questions.What is the IPv4 address of the workstation?What is the IPv4 address of the workstation?

192.168.0.35192.168.0.35

What is the subnet mask?What is the subnet mask?

255.255.255.0255.255.255.0

What is the default gateway address?What is the default gateway address?

192.168.0.5192.168.0.5

What is the address of the first DNS server that the workstation will use for name resolution?What is the address of the first DNS server that the workstation will use for name resolution?

192.168.0.11192.168.0.11

How did the computer get its IP configuration information?How did the computer get its IP configuration information?

DHCPDHCP

ExplanationExplanationYou can use the You can use the ipconfig ipconfig command to find the IP address and subnet mask. You will need to use command to find the IP address and subnet mask. You will need to use ipconfig /all ipconfig /all to find the default gateway,to find the default gateway,DNS server, and DHCP server addresses. Because the DHCP server line has a value, this computer got its configuration information from aDNS server, and DHCP server addresses. Because the DHCP server line has a value, this computer got its configuration information from aDHCP server.DHCP server.[q_ipconfig1_pp6.question.xml Q_IPCONFIG1_PP6][q_ipconfig1_pp6.question.xml Q_IPCONFIG1_PP6]

ResetReset





Click the Click the View Lab View Lab button and use the lab interface to find the answers to the following questions.button and use the lab interface to find the answers to the following questions.What is the IPv4 address of the workstation?What is the IPv4 address of the workstation?

169.254.201.11169.254.201.11


255.255.0.0255.255.0.0


APIPAAPIPA

What type of Internet access would this computer have?What type of Internet access would this computer have?

No accessNo access

ExplanationExplanationYou can use the You can use the ipconfig ipconfig command to find the IP address and subnet mask. You will need to use command to find the IP address and subnet mask. You will need to use ipconfig /all ipconfig /all to find additionalto find additionalinformation, such as whether the computer got addressing information from a DHCP server or not.information, such as whether the computer got addressing information from a DHCP server or not.

In this scenario, the computer is configured to get information from a DHCP server (DHCP Enabled = Yes), but the DHCP server line isIn this scenario, the computer is configured to get information from a DHCP server (DHCP Enabled = Yes), but the DHCP server line ismissing, meaning that the computer could not contact a DHCP server. The Autoconfiguration Enabled line indicates Yes, meaning that themissing, meaning that the computer could not contact a DHCP server. The Autoconfiguration Enabled line indicates Yes, meaning that thecomputer will use APIPA if the DHCP server is unavailable. An address beginning with 169.254.x.x with a mask of 255.255.0.0 indicates thatcomputer will use APIPA if the DHCP server is unavailable. An address beginning with 169.254.x.x with a mask of 255.255.0.0 indicates thatthe computer used APIPA to assign itself an IP address.the computer used APIPA to assign itself an IP address.

Because the computer does not have a default gateway address, it will be unable to communicate on the Internet. Communications will beBecause the computer does not have a default gateway address, it will be unable to communicate on the Internet. Communications will belimited to the local subnet only.limited to the local subnet only.[q_ipconfig2_pp6.question.xml Q_IPCONFIG2_PP6][q_ipconfig2_pp6.question.xml Q_IPCONFIG2_PP6]

ResetReset





Click the Click the View Lab View Lab button and use the lab interface to find the answers to the following questions.button and use the lab interface to find the answers to the following questions.What is the IPv4 address of the server?What is the IPv4 address of the server?

192.168.0.14192.168.0.14


255.255.255.0255.255.255.0


Static (manual) configurationStatic (manual) configuration

Assuming the default gateway computer is connected to the Internet, what type of Internet access would this computer have?Assuming the default gateway computer is connected to the Internet, what type of Internet access would this computer have?

Full accessFull access

ExplanationExplanationYou can use the You can use the ipconfig ipconfig command to find the IP address and subnet mask. You will need to use command to find the IP address and subnet mask. You will need to use ipconfig /all ipconfig /all to find additionalto find additionalinformation, such as whether the computer got addressing information from a DHCP server or not.information, such as whether the computer got addressing information from a DHCP server or not.

In this scenario, the computer is statically configured with the IP address and mask (the DHCP Enabled line = No).In this scenario, the computer is statically configured with the IP address and mask (the DHCP Enabled line = No).

The computer has full access to the Internet.The computer has full access to the Internet.[q_ipconfig3_pp6.question.xml Q_IPCONFIG3_PP6][q_ipconfig3_pp6.question.xml Q_IPCONFIG3_PP6]

ResetReset


Lab Report: 6.9.6 Use ifconfig

Your Performance


Task Summary

Actions you were required to perform:In Start the enp2s1 network interface card


Determine which network interface went down when it was unplugged.Start the network interface from the command line.


1. At the prompt, type any of the following commands and press Enter to view information about the networkinterfaces to determine which card is not up and to identify the card alias. (The alias for the network interface thatis down is enp2s1.)

ip addrip addr showip addr show enp2s1ifconfig -a

2. Type either of the following commands and press Enter to start the enp2s1 network interface:ifup enp2s1ip link set enp2s1 up


Lab Report: 6.10.4 Fix a Network Connection 1

Your Performance


Task Summary

Actions you were required to perform:In Plug the workstation into the network

In Configure TCP/IP settingsHide Details

Configure a valid IP address

Use 255.255.255.0 for the Subnet mask

Use 192.168.0.5 for the Default Gateway

Configure 163.128.80.93 or 163.128.78.93 as the Preferred DNS server


Connect the computer to the network.Modify the TCP/IP settings for the computer to match the network configuration:

Workstation IP address, choose any address between 192.168.0.15 and 192.168.0.254 except for the addressesof the workstations (192.168.0.30 - 192.168.0.34).Subnet mask: 255.255.255.0Default gateway: 192.168.0.5DNS server: either 163.128.80.93 or 163.128.78.93 (default values).


1. Verify the problem as follows:a. In the notification area, right-click the Network icon and select Open Network & Internet settings. The

network map shows no connection to the internet.b. Select Change adapter options to help determine why.c. Notice the status for the network connection is network cable unplugged.d. Close the window.

2. Connect the cable as follows:a. In the top navigation tabs, select Office 1 to work with the computer hardware.b. Above the computer, select Back to switch to the back view of the computer.

The computer has a network cable, but the link light is not on.c. Select the network cable connected to the computer to see what is connected to the other end.

In the Selected Component window, notice that one end is unconnected.d. Select the unconnected end and drag it to the network connection on the wall plate.

3. Fix settings as follows:a. On the monitor, select Click to view Windows 10 to switch to the operating system view.

The notification area shows a network connection.The network map in the Network Status does not show an internet connection.

b. Maximize the Network Status window for easier viewing.c. Select Network and Sharing Center.d. Select Ethernet.e. Select Details.f. Compare the current TCP/IP configuration with the required configuration shown in the Exhibit.g. Click Close.h. Select Properties to modify the TCP/IP configuration.

i. Select Internet Protocol Version 4 (TCP/IPv4).j. Select Properties.

k. In the IP address field, enter a correct IP address.l. In the Subnet mask field, enter 255.255.255.0.

m. In the Default gateway field, enter 192.168.0.5.n. In the Preferred DNS server field, enter a correct DNS server address.o. Click OK.p. Click Close.q. Verify the internet connection in the Network and Sharing Center.


Lab Report: 6.10.5 Fix a Network Connection 2

Your Performance


Task Summary

Actions you were required to perform:In Replace the network cable with the Cat6a cable

In Connect to the network


Diagnose and correct the problem.If necessary, replace any non-working parts with spare parts from the Workspace.Do not replace working parts with parts from the Shelf. The lab should end with all original working parts installed inthe computer (except for those parts that do not work).If you remove any working parts as you troubleshoot, be sure to replace them in the computer before ending the lab.Place any unused parts back on the Shelf.


1. In the notification area, hover the mouse over the Network icon. Notice that the computer is not connected to thenetwork.

2. Get more information about the problem as follows:a. Right-click Start and select Windows PowerShell.b. At the command prompt, type ipconfig and press Enter to view information about the network adapter.

Notice that the media is disconnected.3. Verify the physical configuration of the computer as follows:

a. From the top navigation tabs, select Support Office.b. Above the computer, select Back to switch to the back view of the computer.c. Select the network cable.d. Make sure the other end of the network cable is plugged into the wall outlet.

Because the network cable is connect to the computer and the wall outlet, it appears that the cable mightbe faulty.

4. Connect to the network using a known good networking cable as follows:a. On the back of the computer, drag the RJ45 connector to the Workspace to disconnect it.b. Drag the RJ45 connector from the wall outlet to the Shelf.c. On the Shelf, select the CAT6a Cable because it gives you 100 Mbps or greater speeds.d. Under Selected Component, drag the RJ45 connector to the network card on the computer.e. Under Selected Component, drag a other RJ45 connector to the network connection on the wall outlet.

5. On the Support monitor, select Click to view Windows 10 to switch to the operating system view.6. Verify the connection as follows:

a. At the command prompt, type ipconfig and press Enter.b. In the notification area, right-click the Network icon and select Open Network & Internet settings.c. Verify the status of the Ethernet.

explanation your performanceuse dhcp for dns server information in configure an alternate ip...

Documents