InstallationInstallationInstructionsInstructions& Recommended

Procedures

LASER DEFUSER EX(FRONT LICENSE PLATE MOUNT WITH FRAME) 1. Remove the mounting bolts and any existing frame or cover from the license plate. Remove license plate.

2. Position the Laser Defuser EX around the existing front license plate and mount it against the factory licenseplate bracket. Use the existing mounting bolts or K40 supplied nylon bolts to secure the Laser Defuser EXframe and license plate to the bracket.

The Defuser EX system is ideal for small to mid-size vehicles, and comes packaged in an ordinary lookinglicense plate frame. It may be installed with or without the license plate frame as needed.

The Defuser EX2 system is recommended for larger size vehicles, or when a front license plate mountis not used on the vehicle. The system includes two separate Defuser modules with no license plate frames.

On vehicles that have only one set of bracket mounting holes, it is recommended that the LaserDefuser EX and the license plate be bolted together to eliminate any vibration.

DIAGRAM A3

3. For proper performance, the Defuser EX must be mounted completely level. A unit which is positioned up,down, or to the side by as little as 1° can reduce jamming effectiveness by as much as several hundred feet(see diagram A1).

To assure the Defuser EX is properly leveled, insert the rod on the K40 supplied level into the leveling assem-bly hole located on the top of the Defuser EX frame (see diagram A2). Be sure that the vehicle is on a levelsurface before checking installation.

NOTE:

DIAGRAM A1

DIAGRAM A2

Use the K40 supplied nylon nuts and bolts to correct either up ordown as needed (see diagram A3).

4. Route the black cable into the enginecompartment either through the grillor under the bumper. Connect wiresper the separate enclosed block diagram sheet.

On some vehicles, it may be necessary to adjust or reposition the factory license plate bracket toachieve the desired level installation.NOTE:

LASER DEFUSER

FACTORY MOUNTING LOCATION

MOUNTING NUTS

JAMMING BEAM

LASER DEFUSER EX

EnlargedView

EnlargedView

EnlargedView

JAMMING BEAM

LASER DEFUSER EX

LASER DEFUSER EX

JAMMING BEAM

CORRECT NO NO

LASER DEFUSER EX & EX2(FRONT CUSTOM MOUNT WITHOUT FRAME)

DIAGRAM B1

Diagram B3

BRACKET

TAPE

1/4” SCREW

LASER DEFUSER

BRACKET

TAPE

LASER DEFUSER

1/4” SCREW

WITHOUT HORIZONTALTABS

WITHHORIZONTALTABS

3. If utilizing the supplied universal mounting bracket(s), determine which holes will be used to mount the Defuser module(s) to the vehicle. Remove the unused mounting tabs on the bracket(s) as needed.

4. Apply the supplied double stick tape directly to the Defuser module(s) and attach the module(s) to the universal mounting bracket(s) with the included 1/4” screws ( diagram B3).

1/4”SCREW 1/4”

SCREW

CENTERED & UN-OBSTRUCTED

DO NOT PUT BEHIND GRILLDO NOT OBSTRUCT VIEW

DO NOT MOUNT OFF CENTER

2. For the dual Defuser EX2, choose separate mounting locations on either side of the license plate area and/orcenter of the vehicle. For proper performance, the EX2 modules should be spaced 18" apart from one another, and cannot be obstructed in any way or recessed into the vehicle (see diagram B2).

DO NOT PUT BEHIND GRILLDO NOT OBSTRUCT VIEW

DIAGRAM B2

1. For the single Defuser EX, choose a mounting location near the center of the vehicle that has a clear, unob-structed view of the road . Units which are mounted off center, are recessed into the vehicle, or which are obstructed in any way will not perform properly (see diagram B1).

If using an EX system, first separate the module from the license plate frame by removing thetwo screws on the backside of the frame.

NOTE:

CORRECTLY SPACED& UNOBSTRUCTED

DO NOT SPACE MODULESMORE THAN 18” APART

5. Install the Defuser module(s) tothe desired mounting surfaceusing the included 3/4” screwsor nylon mounting nuts andbolts.

6. For proper performance, theDefuser EX and EX2 must bemounted completely level. Aunit which is positioned up,down, or to the side by as littleas 1° can reduce jamming effec-tiveness by as much as severalhundred feet (see diagram B4).

Be sure that the vehicle is on alevel surface before checkinginstallation.

JAMMING BEAM

EnlargedView

JAMMING BEAM

LASER DEFUSER

EnlargedView

NOCORRECT

LASER DEFUSER

DIAGRAM B4

EnlargedView

NO

JAM

MIN

G BE

AM

LASER DEFUSER(S)

EnlargedView

CORRECT

JAMM

ING BEAM

LASER DEFUSER EX & EX2(REAR LICENSE PLATE MOUNT WITHOUT FRAME)

1. Remove the mounting bolts and any existing frame or cover from the rear license plate. Remove license plate.

2. Remove the three unused horizontal mounting tabs from the top of the supplied universal mounting bracket.

3. Apply the supplied double stick tape directly to the Defuser module and attach it to the mounting bracket withthe included 1/4” screws. Position the Defuser module against the license plate and mount it to the factory license plate bracket using the existing mounting bolts or K40 supplied nylon bolts (see diagram C1)

To assure the Defuser module(s) is/are properly leveled, insert the rodon the K40 supplied level into the leveling assembly hole located nearthe middle of the Defuser module(s)(see diagram B5).

7. Route the black cable(s) into the engine compartment, either throughthe grill or under the bumper. Connect the Defuser EX or EX2 wiresper the separate enclosed block diagram sheet.DIAGRAM B5

If using an EX system, first separate the module from the license plate frame by removing thetwo screws on the backside of the frame.

NOTE:

DIAGRAM C1

40

JAM

MIN

G BE

AM

JAM

MIN

G BE

AM

LASER DEFUSER(S)

LASER DEFUSER

FACTORY MOUNTING LOCATION

LASER DEFUSER

FACTORY MOUNTING LOCATION

LASER DEFUSER

FACTORY MOUNTING LOCATION

DIAGRAM C2

4. For proper performance, the Defuser module must be mounted completely level. A module which is posi-tioned up, down, or to the side by as little as 1° can reduce jamming effectiveness by as much as several hundred feet (see diagram C2). To assure the Defuser module is properly leveled, insert the rod on the K40 supplied level into the leveling assembly hole located near the middle of the Defuser module (see diagram C3).Be sure that the vehicle is on a level surface before checking installation.

5. Route the black cable into the trunk. Connect wires per the separate enclosed block diagram sheet.

44678 6/07

DIAGRAM C3

LASER DEFUSER EX(REAR LICENSE PLATE MOUNT WITH FRAME)

1. Remove the mounting bolts and any existing frame or cover from the license plate. Remove license plate.

2. Position the Laser Defuser EX around the existing rear license plate and mount it against the factory licenseplate bracket. Use the existing mounting bolts or K40 supplied nylon bolts to secure the Laser Defuser EXframe and license plate to the bracket.

On vehicles that have only one set of bracket mounting holes, it is recommended that the LaserDefuser EX and the license plate be bolted together to eliminate any vibration.

3. For proper performance, the Defuser EX must be mounted completely level. A unit which is positioned up,down, or to the side by as little as 1° can reduce jamming effectiveness by as much as several hundred feet(see diagram D1). To assure the Defuser EX is properly leveled, insert the rod on the K40 supplied level intothe leveling assembly hole located on the top of the Defuser EX frame (see diagram D2). Be sure that the vehicle is on a level surface before checking installation.

4. Use the K40 supplied nylon nuts and bolts to correct either up or down as needed ).

5. Route the black cable into the trunk. Connect wires per the separate enclosed block diagram sheet.

NOTE:

LASER DEFUSER

FACTORY MOUNTING LOCATION

LASER DEFUSER

FACTORY MOUNTING LOCATION

LASER DEFUSER

FACTORY MOUNTING LOCATION

DIAGRAM D1 DIAGRAM D2