everyday enchantment box tutorial

7/31/2019 Everyday Enchantment Box Tutorial

1/9

Everyday Enchantment Box

Box Designed by Tara Bilbao

Tutorial Designed by Heather Cserni

Supplies:

Poppy Parade CS Retired Pool Party CS - 122924 Everyday Enchantment DSP Retired Everyday Enchantment Brads - Retired Simply Scored Scoring Tool 122334 Paper Snips 103579 Sticky Strip 104294 Snail Adhesive - 104332 1 Circle Punch 119868 Circle Punch 119873 1/16 Circle Handheld Punch 101227 Big Shot 113439 Adorning Accents Edgelits 125595 Non - Stampin Up! Velcro Dots


2/9

Measurements:

Poppy Parade CS8 x 9 (1)

8 x 5 (1)

Everyday Enchantment DSP TIP: When cutting out your DSP make sure you have thepattern going the same way on all of your pieces. I made this mistake cutting my DSP out

the first time.

5 x 3 (1)

7 x 5 (1)

1 x 4 (2)

How its done:

1. Grab your 8 x 9 sheet of Poppy Parade CS. With the 8 side facing the top of thescoring board score your CS at 1 and 7 .


3/9

2. Turn your CS so that the 9 side is now facing the top of your scoring board and scoreyour CS at (only to your already scored lines - see what I mean in the photograph

below), 1 , 5 and 7.

3. Cut CS as shown. This is the back of the box and the front flap.


4/9

4. Grab your 8 x 5 Poppy Parade CS. Score your CS at 1 on 3 of your sides.

5. Turn your CS so the 5 side is facing the top of your scoring board and score your CS at (only to your already scored lines see what I mean in the photograph below).

Forgive my boo-boo with my pen!


5/9

6. Cut CS as shown. This is the front of your box.

7. Using your Adorning Accent Edgelit cut CS pieces as shown below :

This is your box front This is your box back


6/9

8. Cut the remaining 2 pieces of CS that is keeping you from having the Edgelit shape. Seephotograph below.

9. Using your Edgelit cut your DSP the same direction you cut your CS above. Assemble asshown below and place your sticky strip in the locations shown below as well.

Forgive the red tape on red paper, whoops!

In case you cannot see the sticky strip you need to place a strip on both of your tabs,

closest to where your 1 x 4 DSP meets your score line. Make sense?


7/9

On this piece once again if you cannot see the sticky strip you will need to place a line of

sticky strip going down both sides of your box closest to your DSP. You will need to place

a strip going sideways on both of your tabs. On the bottom piece of CS you will need to

place two strips of sticky strip one on top by your DSP and the other on bottom running

along the edge.

10.Peel your sticky strip off of your tabs and assemble each box as shown below.


8/9

11.Read this step carefully so you do not mess up your box!! Peel your sticky strip off of theremaining locations. CAREFULLY place the front of the box AROUND the back of the

boxes sides. The front piece hugs the back piece. The front piece covers the backs sides

and the backs bottom. You want your DSP that is on the front sides of your box to beshowing.

12.Take your Velcro Dot (both pieces of it, stacked on top of each other) and place it in themiddle of your flap along the edge. Press your flap closed, applying enough pressure for

the pieces to now separate when you open it.

13.Using your 1 Circle Punch, punch out a piece of Pool Party CS. Using your CirclePunch, punch out a piece of Poppy Parade CS. Crumble each circle up and distress it

enough until you can pull the layers apart. Reassemble your circles.

14.Taking your handheld punch, punch a hole in the middle of your circle layers and placeyour brad through this hole. Adhere to the middle of your flap on the front side for a

cute embellishment


9/9

Another version of the box.

everyday enchantment box tutorial

Documents