eureka easyclean 71c power cord replacement · step 7 — power cord pull out the switch board....
TRANSCRIPT
Eureka EasyClean 71C Power CordReplacement
This guide covers how to replace the vacuum’s power cord.
Written By: Tanner Durnil
Eureka EasyClean 71C Power Cord Replacement Draft: 2017-12-29Guide ID: 100557 -
This document was generated on 2019-09-28 07:03:33 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 7
INTRODUCTION
While the power cord is built to last for quite a while, it can still suffer from wear-and-tear.Additionally, accidents that damage the power cord can happen. This guide covers how to replacethe vacuum’s power cord.
TOOLS:iFixit Opening Tools (1)Phillips #2 Screwdriver (1)Metal Spudger (1)Soldering Workstation (1)
Eureka EasyClean 71C Power Cord Replacement Draft: 2017-12-29Guide ID: 100557 -
This document was generated on 2019-09-28 07:03:33 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 2 of 7
Step 1 — Bottom Cover
Unscrew the two 18.1 mm PH2Phillips head screws on the bottomof the vacuum.
Step 2
Pry off the Riser Visor using theplastic opening tool.
Eureka EasyClean 71C Power Cord Replacement Draft: 2017-12-29Guide ID: 100557 -
This document was generated on 2019-09-28 07:03:33 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 3 of 7
Step 3
Remove the screw cap using themetal spudger.
First-time removal of the screw capcan be difficult. The screw cap isn’tvital, so don’t worry about damagingthe screw cap and just keep tryinguntil it comes out.
Step 4
Unscrew the 14mm PH2 Phillips head screw.
Pull the bottom cover off of the rest of the casing.
Eureka EasyClean 71C Power Cord Replacement Draft: 2017-12-29Guide ID: 100557 -
This document was generated on 2019-09-28 07:03:33 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 4 of 7
Step 5 — Casing
Pull the power switch all the way upand remove the dust cup.
Step 6
Unscrew the six 18.1mm PH2 Phillips head screws on the side of the vacuum.
Pull the casing apart.
Eureka EasyClean 71C Power Cord Replacement Draft: 2017-12-29Guide ID: 100557 -
This document was generated on 2019-09-28 07:03:33 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 5 of 7
Step 7 — Power Cord
Pull out the switch board.
Ensure the vacuum is powered offand unplugged before handling anyelectronics.
Step 8
Desolder the highlighted black and white wires.
For instructions on how to solder and desolder wires, visit this guide.
Eureka EasyClean 71C Power Cord Replacement Draft: 2017-12-29Guide ID: 100557 -
This document was generated on 2019-09-28 07:03:33 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 6 of 7
To reassemble your device, follow these instructions in reverse order.
Step 9
Unscrew the 22.3mm PH2 Phillipshead screw.
Remove the power cord.
Eureka EasyClean 71C Power Cord Replacement Draft: 2017-12-29Guide ID: 100557 -
This document was generated on 2019-09-28 07:03:33 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 7 of 7