eton soulra xl woofer wire repair - amazon web services · 2020-02-11 · eton soulra xl woofer...
TRANSCRIPT
Eton Soulra XL Woofer Wire RepairRepair the connection to the woofer of the Eton Soulra XL.
Geschrieben von: Nate Kilmer
Eton Soulra XL Woofer Wire Repair Entwurf: 2019-08-08Anleitung Nr: 56806 -
Dieses Dokument wurde am 2020-02-11 09:52:36 AM (MST) erstellt.
© iFixit — CC BY-NC-SA de.iFixit.com Seite 1 von 9
EINLEITUNG
The Eton Soulra XL has two woofers that are relatively easy to access and reconnect, should onebecome disconnected. This guide will provide step-by-step instructions to disassemble, clean, andrepair loose connections. You will need to know how to solder; review Wie man Lötverbindungenherstellt und entlötet if you are unfamiliar with the process.
WERKZEUGE:Phillips #0 Screwdriver (1)Soldering Workstation (1)Compressed Air (1)2.5 mm Hex Bit (1)T6 Torx Screwdriver (1)Spudger (1)
Eton Soulra XL Woofer Wire Repair Entwurf: 2019-08-08Anleitung Nr: 56806 -
Dieses Dokument wurde am 2020-02-11 09:52:36 AM (MST) erstellt.
© iFixit — CC BY-NC-SA de.iFixit.com Seite 2 von 9
Schritt 1 — Eton Soulra XL Woofer Wire Repair
Gently pull down and out on thefront cover; it should come off easily.
This step is not necessary; if thecover does not come off easily it canbe left on.
Schritt 2
Remove two screws from each sideusing a H2.5 hexagonal screwdriver.
Eton Soulra XL Woofer Wire Repair Entwurf: 2019-08-08Anleitung Nr: 56806 -
Dieses Dokument wurde am 2020-02-11 09:52:36 AM (MST) erstellt.
© iFixit — CC BY-NC-SA de.iFixit.com Seite 3 von 9
Schritt 3
Pry off "Eton" logo from the sidespeaker covers using a pry tool.
Be careful not to break the emblemwhen removing.
Schritt 4
Remove the two screws that werecovered by the "Eton" logo using aPH0 screwdriver.
Eton Soulra XL Woofer Wire Repair Entwurf: 2019-08-08Anleitung Nr: 56806 -
Dieses Dokument wurde am 2020-02-11 09:52:36 AM (MST) erstellt.
© iFixit — CC BY-NC-SA de.iFixit.com Seite 4 von 9
Schritt 5
The side speaker covers shouldcome off easily now; remove them.
Schritt 6
Remove the five screws on theunderside of the device using a PH0screwdriver.
Eton Soulra XL Woofer Wire Repair Entwurf: 2019-08-08Anleitung Nr: 56806 -
Dieses Dokument wurde am 2020-02-11 09:52:36 AM (MST) erstellt.
© iFixit — CC BY-NC-SA de.iFixit.com Seite 5 von 9
Schritt 7
Extend the solar panel into theupright position to access thescrews on the backside of thedevice.
Schritt 8
Remove the three screws at the topof the back panel using H2.5hexagonal screwdriver.
Eton Soulra XL Woofer Wire Repair Entwurf: 2019-08-08Anleitung Nr: 56806 -
Dieses Dokument wurde am 2020-02-11 09:52:36 AM (MST) erstellt.
© iFixit — CC BY-NC-SA de.iFixit.com Seite 6 von 9
Schritt 9
Remove the ten screws on thebackside of the device using a long-neck PH0 screwdriver.
Some of the screws are deep withinthe panel and require an appropriate(long neck PH0) screwdriver toaccess them.
Schritt 10
At this point, the back panel of thedevice should lift off easily. Lift it offand set aside.
Eton Soulra XL Woofer Wire Repair Entwurf: 2019-08-08Anleitung Nr: 56806 -
Dieses Dokument wurde am 2020-02-11 09:52:36 AM (MST) erstellt.
© iFixit — CC BY-NC-SA de.iFixit.com Seite 7 von 9
Schritt 11
Use compressed air to clear awayany dust or debris.
Schritt 12
Inspect wires and locate anyspeaker loose connections.
Eton Soulra XL Woofer Wire Repair Entwurf: 2019-08-08Anleitung Nr: 56806 -
Dieses Dokument wurde am 2020-02-11 09:52:36 AM (MST) erstellt.
© iFixit — CC BY-NC-SA de.iFixit.com Seite 8 von 9
To reassemble your device, follow these instructions in reverse order.
Schritt 13
Solder loose wires back into place.
Use the methods outlined in the ifixitsoldering guide (link in theintroduction).
Eton Soulra XL Woofer Wire Repair Entwurf: 2019-08-08Anleitung Nr: 56806 -
Dieses Dokument wurde am 2020-02-11 09:52:36 AM (MST) erstellt.
© iFixit — CC BY-NC-SA de.iFixit.com Seite 9 von 9