estic merian 6th-chapter 3_equilibrium

69
Please note: this sample chapter is unproofed.

Upload: wake-up-now-peru

Post on 19-Jan-2015

1.571 views

Category:

Documents


21 download

DESCRIPTION

 

TRANSCRIPT

Page 1: Estic merian 6th-chapter 3_equilibrium

Please note: this sample chapter is unproofed.

Page 2: Estic merian 6th-chapter 3_equilibrium

p11 6191a_ch03 co_2 Tuesday Mar 13 2001 02:20 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

In many applications of mechanics, the sum of the forces acting on a body is zero, and a stateof equilibrium exists. What are the two primary forces acting on each slowly moving balloon?

Page 3: Estic merian 6th-chapter 3_equilibrium

Chapter

3EQUILIBRIUM

CH A P T E R OU T L I N E

3/1 Introduction

SECTION A. Equilibrium in Two Dimensions3/2 System Isolation and the Free-Body Diagram3/3 Equilibrium Conditions

SECTION B. Equilibrium in Three Dimensions3/4 Equilibrium Conditions

3/1 INTRODUCTION

Statics deals primarily with the description of the force con-ditions necessary and sufficient to maintain the equilibrium ofengineering structures. This chapter on equilibrium, therefore,constitutes the most important part of statics, and the proceduresdeveloped here form the basis for solving problems in both staticsand dynamics. We will make continual use of the concepts devel-oped in Chapter 2 involving forces, moments, couples, and resul-tants as we apply the principles of equilibrium.

When a body is in equilibrium, the resultant of all forces act-ing on it is zero. Thus, the resultant force R and the resultantcouple M are both zero, and we have the equilibrium equations

R 5 oF 5 0 M 5 oM 5 0 (3/1)

These requirements are both necessary and sufficient conditionsfor equilibrium.

All physical bodies are three-dimensional, but we can treatmany of them as two-dimensional when the forces to which theyare subjected act in a single plane or can be projected onto a singleplane. When this simplification is not possible, the problem mustbe treated as three-dimensional. We will follow the arrangement

p11 6191a_ch03 co_3 Tuesday Mar 13 2001 02:20 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3

Page 4: Estic merian 6th-chapter 3_equilibrium

used in Chapter 2, and discuss in Section A the equilibrium ofbodies subjected to two-dimensional force systems and in SectionB the equilibrium of bodies subjected to three-dimensional forcesystems.

S E C T I O N A E Q U I L I B R I U M I N T W O D I M E N S I O N S

3/2 SYSTEM ISOLATIONAND THE FREE-BODY DIAGRAM

Before we apply Eqs. 3/1, we must define unambiguously theparticular body or mechanical system to be analyzed and repre-sent clearly and completely all forces acting on the body. Omis-sion of a force which acts on the body in question, or inclusion ofa force which does not act on the body, will give erroneous results.

A mechanical system is defined as a body or group of bodieswhich can be conceptually isolated from all other bodies. A systemmay be a single body or a combination of connected bodies. Thebodies may be rigid or nonrigid. The system may also be an iden-tifiable fluid mass, either liquid or gas, or a combination of fluidsand solids. In statics we study primarily forces which act on rigidbodies at rest, although we also study forces acting on fluids inequilibrium.

Once we decide which body or combination of bodies to ana-lyze, we then treat this body or combination as a single body iso-lated from all surrounding bodies. This isolation is accomplishedby means of the free-body diagram, which is a diagrammaticrepresentation of the isolated system treated as a single body.The diagram shows all forces applied to the system by mechanicalcontact with other bodies, which are imagined to be removed. Ifappreciable body forces are present, such as gravitational or mag-netic attraction, then these forces must also be shown on the free-body diagram of the isolated system. Only after such a diagramhas been carefully drawn should the equilibrium equations bewritten. Because of its critical importance, we emphasize herethat

the free-body diagram is the most important single step inthe solution of problems in mechanics.

Before attempting to draw a free-body diagram, we must re-call the basic characteristics of force. These characteristics weredescribed in Art. 2/2, with primary attention focused on the vectorproperties of force. Forces can be applied either by direct physicalcontact or by remote action. Forces can be either internal or ex-ternal to the system under consideration. Application of force isaccompanied by reactive force, and both applied and reactive

4 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_4 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Page 5: Estic merian 6th-chapter 3_equilibrium

forces may be either concentrated or distributed. The principle oftransmissibility permits the treatment of force as a sliding vectoras far as its external effects on a rigid body are concerned.

We will now use these force characteristics to develop concep-tual models of isolated mechanical systems. These models enableus to write the appropriate equations of equilibrium, which canthen be analyzed.

Modeling the Action of Forces

Figure 3/1 shows the common types of force application onmechanical systems for analysis in two dimensions. Each exam-ple shows the force exerted on the body to be isolated, by the bodyto be removed. Newton’s third law, which notes the existence of

Art ic le 3/2 System Isolat ion and the Free-Body Diagram 5

p11 6191a_ch03 dm_5 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

θ

θ

MODELING THE ACTION OF FORCES IN TWO-DIMENSIONAL ANALYSISType of Contact and Force Origin

1. Flexible cable, belt,chain, or rope

2. Smooth surfaces

3. Rough surfaces

4. Roller support

5. Freely sliding guide

Action on Body to be Isolated

Force exerted by a flexible cable is always a tension away from the body in the direction of the cable.

Contact force is compressive and is normal to the surface.

Rough surfaces are capable of supporting a tangential compo-nent F (frictional force) as well as a normal component N of the resultant contact force R.

Roller, rocker, or ball support transmits a compressive force normal to the supporting surface.

Collar or slider free to move along smooth guides; can support force normal to guide only.

θ

θ

Weight of cablenegligible

Weight of cablenot negligible

T

T

N

N

N

N

F

R

N N

Figure 3/1

Page 6: Estic merian 6th-chapter 3_equilibrium

an equal and opposite reaction to every action, must be carefullyobserved. The force exerted on the body in question by a contact-ing or supporting member is always in the sense to oppose themovement of the isolated body which would occur if the contact-ing or supporting body were removed.

In Fig. 3/1, Example 1 depicts the action of a flexible cable,belt, rope, or chain on the body to which it is attached. Becauseof its flexibility, a rope or cable is unable to offer any resistanceto bending, shear, or compression and therefore exerts only a ten-sion force in a direction tangent to the cable at its point of at-tachment. The force exerted by the cable on the body to which itis attached is always away from the body. When the tension T islarge compared with the weight of the cable, we may assume that

6 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_6 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

MODELING THE ACTION OF FORCES IN TWO-DIMENSIONAL ANALYSIS (cont.)Type of Contact and Force Origin

6. Pin connection

7. Built-in or fixed support

8. Gravitational attraction

9. Spring action

Action on Body to be Isolated

A freely hinged pin connection is capable of supporting a force in any direction in the plane normal to the axis; usually shown as two components Rx and Ry. A pin not free to turn may also support a couple M.

A built-in or fixed support is capable of supporting an axial force F, a transverse force V (shear force), and a couple M (bending moment) to prevent rotation.

The resultant of gravitational attraction on all elements of a body of mass m is the weight W = mg and acts toward the center of the earth through the center mass G.

Spring force is tensile if spring is stretched and compressive if compressed. For a linearly elastic spring the stiffness k is the force required to deform the spring a unit distance.

Pinfree

to turn

Pinnot freeto turn

Ry

Rx

Ry

MRx

Weld

A

M

F

V

orAA

W = mg

F

Gm

Fx

F = kxHardening

NonlinearLinearNeutralposition

Softening

F

x

F

x

Figure 3/1, continued

Page 7: Estic merian 6th-chapter 3_equilibrium

the cable forms a straight line. When the cable weight is not neg-ligible compared with its tension, the sag of the cable becomesimportant, and the tension in the cable changes direction andmagnitude along its length.

When the smooth surfaces of two bodies are in contact, as inExample 2, the force exerted by one on the other is normal to thetangent to the surfaces and is compressive. Although no actualsurfaces are perfectly smooth, we can assume this to be so forpractical purposes in many instances.

When mating surfaces of contacting bodies are rough, as inExample 3, the force of contact is not necessarily normal to thetangent to the surfaces, but may be resolved into a tangential orfrictional component F and a normal component N.

Example 4 illustrates a number of forms of mechanical sup-port which effectively eliminate tangential friction forces. Inthese cases the net reaction is normal to the supporting surface.

Example 5 shows the action of a smooth guide on the body itsupports. There cannot be any resistance parallel to the guide.

Example 6 illustrates the action of a pin connection. Such aconnection can support force in any direction normal to the axisof the pin. We usually represent this action in terms of two rec-tangular components. The correct sense of these components ina specific problem depends on how the member is loaded. Whennot otherwise initially known, the sense is arbitrarily assignedand the equilibrium equations are then written. If the solution ofthese equations yields a positive algebraic sign for the force com-ponent, the assigned sense is correct. A negative sign indicatesthe sense is opposite to that initially assigned.

If the joint is free to turn about the pin, the connection cansupport only the force R. If the joint is not free to turn, the con-nection can also support a resisting couple M. The sense of M isarbitrarily shown here, but the true sense depends on how themember is loaded.

Example 7 shows the resultants of the rather complex distri-bution of force over the cross section of a slender bar or beam ata built-in or fixed support. The sense of the reactions F and V andthe bending couple M in a given problem depends, of course, onhow the member is loaded.

One of the most common forces is that due to gravitationalattraction, Example 8. This force affects all elements of mass ina body and is, therefore, distributed throughout it. The resultantof the gravitational forces on all elements is the weight W 5 mgof the body, which passes through the center of mass G and isdirected toward the center of the earth for earthbound structures.The location of G is frequently obvious from the geometry of thebody, particularly where there is symmetry. When the location isnot readily apparent, it must be determined by experiment orcalculations.

Similar remarks apply to the remote action of magnetic andelectric forces. These forces of remote action have the same over-

Art ic le 3/2 System Isolat ion and the Free-Body Diagram 7

p11 6191a_ch03 dm_7 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Page 8: Estic merian 6th-chapter 3_equilibrium

all effect on a rigid body as forces of equal magnitude and direc-tion applied by direct external contact.

Example 9 illustrates the action of a linear elastic spring andof a nonlinear spring with either hardening or softening charac-teristics. The force exerted by a linear spring, in tension or com-pression, is given by F 5 kx, where k is the stiffness of the springand x is its deformation measured from the neutral or unde-formed position.

The representations in Fig. 3/1 are not free-body diagrams,but are merely elements used to construct free-body diagrams.Study these nine conditions and identify them in the problemwork so that you can draw the correct free-body diagrams.

8 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_8 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Construction of Free-Body Diagrams

The full procedure for drawing a free-body diagram which iso-lates a body or system consists of the following steps.

Step 1. Decide which system to isolate. The system chosenshould usually involve one or more of the desired unknownquantities.

Step 2. Next isolate the chosen system by drawing a diagramwhich represents its complete external boundary. This boundarydefines the isolation of the system from all other attracting orcontacting bodies, which are considered removed. This step is of-ten the most crucial of all. Make certain that you have completelyisolated the system before proceeding with the next step.

Step 3. Identify all forces which act on the isolated systemas applied by the removed contacting and attracting bodies, andrepresent them in their proper positions on the diagram of theisolated system. Make a systematic traverse of the entire bound-ary to identify all contact forces. Include body forces such asweights, where appreciable. Represent all known forces by vectorarrows, each with its proper magnitude, direction, and sense in-dicated. Each unknown force should be represented by a vectorarrow with the unknown magnitude or direction indicated bysymbol. If the sense of the vector is also unknown, you must ar-bitrarily assign a sense. The subsequent calculations with theequilibrium equations will yield a positive quantity if the correctsense was assumed and a negative quantity if the incorrect sensewas assumed. It is necessary to be consistent with the assignedcharacteristics of unknown forces throughout all of the calcula-tions. If you are consistent, the solution of the equilibrium equa-tions will reveal the correct senses.

Step 4. Show the choice of coordinate axes directly on thediagram. Pertinent dimensions may also be represented for con-venience. Note, however, that the free-body diagram serves thepurpose of focusing attention on the action of the external forces,and therefore the diagram should not be cluttered with excessive

Page 9: Estic merian 6th-chapter 3_equilibrium

extraneous information. Clearly distinguish force arrows from ar-rows representing quantities other than forces. For this purposea colored pencil may be used.

Art ic le 3/2 System Isolat ion and the Free-Body Diagram 9

p11 6191a_ch03 dm_9 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Completion of the foregoing four steps will produce a correctfree-body diagram to use in applying the governing equations,both in statics and in dynamics. Be careful not to omit from thefree-body diagram certain forces which may not appear at firstglance to be needed in the calculations. It is only through completeisolation and a systematic representation of all external forcesthat a reliable accounting of the effects of all applied and reactiveforces can be made. Very often a force which at first glance maynot appear to influence a desired result does indeed have an in-fluence. Thus, the only safe procedure is to include on the free-body diagram all forces whose magnitudes are not obviouslynegligible.

The free-body method is extremely important in mechanicsbecause it ensures an accurate definition of a mechanical systemand focuses attention on the exact meaning and application of theforce laws of statics and dynamics. Review the foregoing foursteps for constructing a free-body diagram while studying thesample free-body diagrams shown in Fig. 3/2 and the SampleProblems which appear at the end of the next article.

Examples of Free-Body Diagrams

Figure 3/2 gives four examples of mechanisms and structurestogether with their correct free-body diagrams. Dimensions andmagnitudes are omitted for clarity. In each case we treat the en-tire system as a single body, so that the internal forces are notshown. The characteristics of the various types of contact forcesillustrated in Fig. 3/1 are used in the four examples as they apply.

In Example 1 the truss is composed of structural elementswhich, taken all together, constitute a rigid framework. Thus, wemay remove the entire truss from its supporting foundation andtreat it as a single rigid body. In addition to the applied externalload P, the free-body diagram must include the reactions on thetruss at A and B. The rocker at B can support a vertical forceonly, and this force is transmitted to the structure at B (Example4 of Fig. 3/1). The pin connection at A (Example 6 of Fig. 3/1) iscapable of supplying both a horizontal and a vertical force com-ponent to the truss. If the total weight of the truss members isappreciable compared with P and the forces at A and B, then theweights of the members must be included on the free-body dia-gram as external forces.

In this relatively simple example it is clear that the verticalcomponent Ay must be directed down to prevent the truss fromrotating clockwise about B. Also, the horizontal component Axwill be to the left to keep the truss from moving to the right underthe influence of the horizontal component of P. Thus, in con-

Page 10: Estic merian 6th-chapter 3_equilibrium

structing the free-body diagram for this simple truss, we can eas-ily perceive the correct sense of each of the components of forceexerted on the truss by the foundation at A and can, therefore,represent its correct physical sense on the diagram. When thecorrect physical sense of a force or its component is not easilyrecognized by direct observation, it must be assigned arbitrarily,and the correctness of or error in the assignment is determinedby the algebraic sign of its calculated value.

In Example 2 the cantilever beam is secured to the wall andsubjected to three applied loads. When we isolate that part of thebeam to the right of the section at A, we must include the reactiveforces applied to the beam by the wall. The resultants of thesereactive forces are shown acting on the section of the beam (Ex-

10 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_10 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

A B

P

Ax

F3 F2 F1

Ay By

BxBy

P

y

x

y

x

y

x

y

x

A Mass m

F3 F2 F1

F

M

M

B

AP P

N

V2. Cantilever beam

3. Beam

4. Rigid system of interconnected bodies analyzed as a single unit

1. Plane truss

Weight of trussassumed negligiblecompared with P

Mechanical System Free–Body Diagram of Isolated Body

SAMPLE FREE–BODY DIAGRAMS

W = mg

W = mg

W = mg

Smooth surfacecontact at A.Mass m

P

A B

m

M

Bx

By

Weight of mechanismneglected

P

Ay

Figure 3/2

Page 11: Estic merian 6th-chapter 3_equilibrium

ample 7 of Fig. 3/1). A vertical force V to counteract the excess ofdownward applied force is shown, and a tension F to balance theexcess of applied force to the right must also be included. Then,to prevent the beam from rotating about A, a counterclockwisecouple M is also required. The weight mg of the beam must berepresented through the mass center (Example 8 of Fig. 3/1).

In the free-body diagram of Example 2, we have representedthe somewhat complex system of forces which actually act on thecut section of the beam by the equivalent force–couple system inwhich the force is broken down into its vertical component V(shear force) and its horizontal component F (tensile force). Thecouple M is the bending moment in the beam. The free-body di-agram is now complete and shows the beam in equilibrium underthe action of six forces and one couple.

In Example 3 the weight W 5 mg is shown acting through thecenter of mass of the beam, whose location is assumed known(Example 8 of Fig. 3/1). The force exerted by the corner A on thebeam is normal to the smooth surface of the beam (Example 2 ofFig. 3/1). To perceive this action more clearly, visualize an en-largement of the contact point A, which would appear somewhatrounded, and consider the force exerted by this rounded corneron the straight surface of the beam, which is assumed to besmooth. If the contacting surfaces at the corner were not smooth,a tangential frictional component of force could exist. In additionto the applied force P and couple M, there is the pin connectionat B, which exerts both an x- and a y-component of force on thebeam. The positive senses of these components are assignedarbitrarily.

In Example 4 the free-body diagram of the entire isolatedmechanism contains three unknown forces if the loads mg and Pare known. Any one of many internal configurations for securingthe cable leading from the mass m would be possible without af-fecting the external response of the mechanism as a whole, andthis fact is brought out by the free-body diagram. This hypothet-ical example is used to show that the forces internal to a rigidassembly of members do not influence the values of the externalreactions.

We use the free-body diagram in writing the equilibriumequations, which are discussed in the next article. When theseequations are solved, some of the calculated force magnitudesmay be zero. This would indicate that the assumed force does notexist. In Example 1 of Fig. 3/2, any of the reactions Ax, Ay, or Bycan be zero for specific values of the truss geometry and of themagnitude, direction, and sense of the applied load P. A zero re-action force is often difficult to identify by inspection, but can bedetermined by solving the equilibrium equations.

Similar comments apply to calculated force magnitudeswhich are negative. Such a result indicates that the actual senseis the opposite of the assumed sense. The assumed positive sensesof Bx and By in Example 3 and By in Example 4 are shown on thefree-body diagrams. The correctness of these assumptions is

Art ic le 3/2 System Isolat ion and the Free-Body Diagram 11

p11 6191a_ch03 dm_11 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Page 12: Estic merian 6th-chapter 3_equilibrium

proved or disproved according to whether the algebraic signs ofthe computed forces are plus or minus when the calculations arecarried out in an actual problem.

The isolation of the mechanical system under considerationis a crucial step in the formulation of the mathematical model.The most important aspect to the correct construction of the all-important free-body diagram is the clear-cut and unambiguousdecision as to what is included and what is excluded. This deci-sion becomes unambiguous only when the boundary of the free-body diagram represents a complete traverse of the body orsystem of bodies to be isolated, starting at some arbitrary pointon the boundary and returning to that same point. The systemwithin this closed boundary is the isolated free body, and all con-tact forces and all body forces transmitted to the system acrossthe boundary must be accounted for.

The following exercises provide practice with drawing free-body diagrams. This practice is helpful before using such dia-grams in the application of the principles of force equilibrium inthe next article.

12 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_12 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Page 13: Estic merian 6th-chapter 3_equilibrium

FREE-BODY DIAGRAM EXERCISES

3/A In each of the five following examples, the body to beisolated is shown in the left-hand diagram, and an in-complete free-body diagram (FBD) of the isolated bodyis shown on the right. Add whatever forces are nec-

Art ic le 3/2 Free-Body Diagram Exerc ises 13

p11 6191a_ch03 dm_13 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

essary in each case to form a complete free-body dia-gram. The weights of the bodies are negligible unlessotherwise indicated. Dimensions and numerical val-ues are omitted for simplicity.

1. Bell crank supporting mass m with pin support at A.

2. Control lever applying torque to shaft at O.

3. Boom OA, of negligible mass compared with mass m. Boom hinged at O and supported by hoisting cable at B.

4. Uniform crate of mass m leaning against smooth vertical wall and supported on a rough horizontal surface.

5. Loaded bracket supported by pin connection at A and fixed pin in smooth slot at B.

Body Incomplete FBD

m

A

O

A

B

A

OO

A

B

T

A

mgT

Flexiblecable

Pull P P

FO

m mg

mg

B

B

ALoad L

B

AL

Figure 3/A

Page 14: Estic merian 6th-chapter 3_equilibrium

3/B In each of the five following examples, the body to beisolated is shown in the left-hand diagram, and eithera wrong or an incomplete free-body diagram (FBD) isshown on the right. Make whatever changes or addi-

14 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_14 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

tions are necessary in each case to form a correct andcomplete free-body diagram. The weights of the bodiesare negligible unless otherwise indicated. Dimensionsand numerical values are omitted for simplicity.

mg

mg

1.

Wrong or Incomplete FBDBody

P

P

N

N

PLawn roller of mass m beingpushed up incline .

5. Bent rod welded tosupport at A and subjected to two forces and couple.

4. Supporting anglebracket for frame.Pin joints

3. Uniform pole of mass m beinghoisted into posi-tion by winch. Horizontal sup-porting surfacenotched to preventslipping of pole.

2. Pry bar lifting body A having smooth horizontal surface. Bar rests on horizontal rough surface.

θ θ

P

T

R

R

A

Notch

y

x

M

F

M

F

P

A y

F

A

A

B

P

A

B

Figure 3/B

Page 15: Estic merian 6th-chapter 3_equilibrium

3/C Draw a complete and correct free-body diagram ofeach of the bodies designated in the statements. Theweights of the bodies are significant only if the massis stated. All forces, known and unknown, should be

Art ic le 3/2 Free-Body Diagram Exerc ises 15

p11 6191a_ch03 dm_15 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

labeled. (Note: The sense of some reaction componentscannot always be determined without numericalcalculation.)

m

L

A

A B

A

A

B

C

A

B

B

3. Loaded truss supported by pin joint at A and by cable at B.

2. Wheel of mass m on verge of beingrolled over curb by pull P.

4. Uniform bar of mass m and roller ofmass m0 taken together. Subjected to couple M and supported as shown.Roller is free to turn.

7. Uniform heavy plate of mass msupported in vertical plane by cableC and hinge A.

6. Bar, initially horizontal but deflected under load L. Pinned to rigid support at each end.

8. Entire frame, pulleys, and contactingcable to be isolated as a single unit.

1. Uniform horizontal bar of mass m suspended by vertical cable at A andsupported by rough inclined surface at B.

5. Uniform grooved wheel of mass msupported by a rough surface and by action of horizontal cable.

m0M

A

m

P

m

L

m

L

Figure 3/C

Page 16: Estic merian 6th-chapter 3_equilibrium

3/3 EQUILIBRIUM CONDITIONS

In Art. 3/1 we defined equilibrium as the condition in whichthe resultant of all forces and moments acting on a body is zero.Stated in another way, a body is in equilibrium if all forces andmoments applied to it are in balance. These requirements arecontained in the vector equations of equilibrium, Eqs. 3/1, whichin two dimensions may be written in scalar form as

oF 5 0 oF 5 0 oM 5 0 (3/2)x y O

The third equation represents the zero sum of the moments of allforces about any point O on or off the body. Equations 3/2 are thenecessary and sufficient conditions for complete equilibrium intwo dimensions. They are necessary conditions because, if theyare not satisfied, there can be no force or moment balance. Theyare sufficient because once they are satisfied, there can be noimbalance, and equilibrium is assured.

The equations relating force and acceleration for rigid-bodymotion are developed in Vol. 2 Dynamics from Newton’s secondlaw of motion. These equations show that the acceleration of themass center of a body is proportional to the resultant force oFacting on the body. Consequently, if a body moves with constantvelocity (zero acceleration), the resultant force on it must be zero,and the body may be treated as in a state of translationalequilibrium.

For complete equilibrium in two dimensions, all three of Eqs.3/2 must hold. However, these conditions are independent re-quirements, and one may hold without another. Take, for exam-ple, a body which slides along a horizontal surface withincreasing velocity under the action of applied forces. The force–equilibrium equations will be satisfied in the vertical directionwhere the acceleration is zero, but not in the horizontal direction.Also, a body, such as a flywheel, which rotates about its fixedmass center with increasing angular speed is not in rotationalequilibrium, but the two force–equilibrium equations will besatisfied.

Categories of Equilibrium

Applications of Eqs. 3/2 fall naturally into a number of cate-gories which are easily identified. The categories of force systemsacting on bodies in two-dimensional equilibrium are summarizedin Fig. 3/3 and are explained further as follows.

Category 1, equilibrium of collinear forces, clearly requiresonly the one force equation in the direction of the forces (x-direc-tion), since all other equations are automatically satisfied.

Category 2, equilibrium of forces which lie in a plane (x-yplane) and are concurrent at a point O, requires the two force

16 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_16 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Page 17: Estic merian 6th-chapter 3_equilibrium

equations only, since the moment sum about O, that is, about az-axis through O, is necessarily zero. Included in this category isthe case of the equilibrium of a particle.

Category 3, equilibrium of parallel forces in a plane, requiresthe one force equation in the direction of the forces (x-direction)and one moment equation about an axis (z-axis) normal to theplane of the forces.

Category 4, equilibrium of a general system of forces in aplane (x-y), requires the two force equations in the plane and onemoment equation about an axis (z-axis) normal to the plane.

Two- and Three-Force Members

You should be alert to two frequently occurring equilibriumsituations. The first situation is the equilibrium of a body underthe action of two forces only. Two examples are shown in Fig. 3/4,and we see that for such a two-force member to be in equilibrium,the forces must be equal, opposite, and collinear. The shape of themember does not affect this simple requirement. In the illustra-tions cited, we consider the weights of the members to be negli-gible compared with the applied forces.

Art ic le 3/3 Equi l ibr ium Condi t ions 17

p11 6191a_ch03 dm_17 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

y

x

y

x

y

x

xF3

F1

2. Concurrent at a point

3. Parallel

4. General

1. Collinear

Force System Independent EquationsFree–Body Diagram

CATEGORIES OF EQUILIBRIUM IN TWO DIMENSIONS

F2

F1

F1

F1 F3

F3F4

F4

F4

F2

F2

F2

F3

Σ Fx = 0

Fx = 0Σ

Fx = 0Σ

Fx = 0Σ

Fy = 0Σ

Mz = 0Σ

Mz = 0Σ

Fy = 0ΣM

O

Figure 3/3

PP

– P – P

Two-force members

Figure 3/4

Page 18: Estic merian 6th-chapter 3_equilibrium

The second situation is a three-force member, which is a bodyunder the action of three forces, Fig. 3/5a. We see that equilib-rium requires the lines of action of the three forces to be concur-rent. If they were not concurrent, then one of the forces wouldexert a resultant moment about the point of intersection of theother two, which would violate the requirement of zero momentabout every point. The only exception occurs when the threeforces are parallel. In this case we may consider the point of con-currency to be at infinity.

The principle of the concurrency of three forces in equilibriumis of considerable use in carrying out a graphical solution of theforce equations. In this case the polygon of forces is drawn andmade to close, as shown in Fig. 3/5b. Frequently, a body in equi-librium under the action of more than three forces may be re-duced to a three-force member by a combination of two or moreof the known forces.

Alternative Equilibrium Equations

In addition to Eqs. 3/2, there are two other ways to expressthe general conditions for the equilibrium of forces in two dimen-sions. The first way is illustrated in Fig. 3/6, parts (a) and (b). Forthe body shown in Fig. 3/6a, if oMA 5 0, then the resultant, if itstill exists, cannot be a couple, but must be a force R passingthrough A. If now the equation oFx 5 0 holds, where the x-direc-tion is arbitrary, it follows from Fig. 3/6b that the resultant forceR, if it still exists, not only must pass through A, but also mustbe perpendicular to the x-direction as shown. Now, if oMB 5 0,where B is any point such that the line AB is not perpendicularto the x-direction, we see that R must be zero, and thus the body

18 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_18 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

ΣMA = 0 satisfied

ΣMA = 0 satisfied

ΣMA = 0 Σ Fx = 0

satisfied

ΣMA = 0 Σ MB = 0

satisfied

(a) (b)

x

(c) (d)

R R

A A

AA

B

C

B

R R

Figure 3/6

F1

F1

F3

F3

F2

F2

Three-force member(a)

Closed polygonsatisfies

(b)ΣF = 0

O

Figure 3/5

Page 19: Estic merian 6th-chapter 3_equilibrium

is in equilibrium. Therefore, an alternative set of equilibriumequations is

oF 5 0 oM 5 0 oM 5 0x A B

where the two points A and B must not lie on a line perpendicularto the x-direction.

A third formulation of the conditions of equilibrium may bemade for a coplanar force system. This is illustrated in Fig. 3/6,parts (c) and (d). Again, if oMA 5 0 for any body such as thatshown in Fig. 3/6c, the resultant, if any, must be a force R throughA. In addition, if oMB 5 0, the resultant, if one still exists, mustpass through B as shown in Fig. 3/6d. Such a force cannot exist,however, if oMC 5 0, where C is not collinear with A and B. Thus,we may write the equations of equilibrium as

oM 5 0 oM 5 0 oM 5 0A B C

where A, B, and C are any three points not on the same straightline.

When equilibrium equations are written which are not inde-pendent, redundant information is obtained, and a correct solu-tion of the equations will yield 0 5 0. For example, for a generalproblem in two dimensions with three unknowns, three momentequations written about three points which lie on the samestraight line are not independent. Such equations will containduplicated information, and solution of two of them can at bestdetermine two of the unknowns, with the third equation merelyverifying the identity 0 5 0.

Constraints and Statical Determinacy

The equilibrium equations developed in this article are bothnecessary and sufficient conditions to establish the equilibriumof a body. However, they do not necessarily provide all the infor-mation required to calculate all the unknown forces which mayact on a body in equilibrium. Whether the equations are adequateto determine all the unknowns depends on the characteristics ofthe constraints against possible movement of the body providedby its supports. By constraint we mean the restriction ofmovement.

In Example 4 of Fig. 3/1 the roller, ball, and rocker provideconstraint normal to the surface of contact, but none tangent tothe surface. Thus, a tangential force cannot be supported. For thecollar and slider of Example 5, constraint exists only normal tothe guide. In Example 6 the fixed-pin connection provides con-straint in both directions, but offers no resistance to rotationabout the pin unless the pin is not free to turn. The fixed supportof Example 7, however, offers constraint against rotation as wellas lateral movement.

Art ic le 3/3 Equi l ibr ium Condi t ions 19

p11 6191a_ch03 dm_19 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Page 20: Estic merian 6th-chapter 3_equilibrium

If the rocker which supports the truss of Example 1 in Fig.3/2 were replaced by a pin joint, as at A, there would be one ad-ditional constraint beyond those required to support an equilib-rium configuration with no freedom of movement. The threescalar conditions of equilibrium, Eqs. 3/2, would not provide suf-ficient information to determine all four unknowns, since Ax andBx could not be solved for separately; only their sum could bedetermined. These two components of force would be dependenton the deformation of the members of the truss as influenced bytheir corresponding stiffness properties. The horizontal reactionsAx and Bx would also depend on any initial deformation requiredto fit the dimensions of the structure to those of the foundationbetween A and B. Thus, we cannot determine Ax and Bx by a rigid-body analysis.

Again referring to Fig. 3/2, we see that if the pin B in Example3 were not free to turn, the support could transmit a couple tothe beam through the pin. Therefore, there would be four un-known supporting reactions acting on the beam, namely, the forceat A, the two components of force at B, and the couple at B. Con-sequently the three independent scalar equations of equilibriumwould not provide enough information to compute all fourunknowns.

A rigid body, or rigid combination of elements treated as asingle body, which possesses more external supports or con-straints than are necessary to maintain an equilibrium positionis called statically indeterminate. Supports which can be removedwithout destroying the equilibrium condition of the body are saidto be redundant. The number of redundant supporting elementspresent corresponds to the degree of statical indeterminacy andequals the total number of unknown external forces, minus thenumber of available independent equations of equilibrium. Onthe other hand, bodies which are supported by the minimumnumber of constraints necessary to ensure an equilibrium config-uration are called statically determinate, and for such bodies theequilibrium equations are sufficient to determine the unknownexternal forces.

The problems on equilibrium in this article and throughoutVol. 1 Statics are generally restricted to statically determinatebodies where the constraints are just sufficient to ensure a stableequilibrium configuration and where the unknown supportingforces can be completely determined by the available independentequations of equilibrium.

We must be aware of the nature of the constraints before weattempt to solve an equilibrium problem. A body can be recog-nized as statically indeterminate when there are more unknownexternal reactions than there are available independent equilib-rium equations for the force system involved. It is always well tocount the number of unknown variables on a given body and tobe certain that an equal number of independent equations can bewritten; otherwise, effort might be wasted in attempting an im-possible solution with the aid of the equilibrium equations only.

20 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_20 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Page 21: Estic merian 6th-chapter 3_equilibrium

The unknown variables may be forces, couples, distances, orangles.

Adequacy of Constraints

In discussing the relationship between constraints and equi-librium, we should look further at the question of the adequacyof constraints. The existence of three constraints for a two-dimensional problem does not always guarantee an equilibriumconfiguration. Figure 3/7 shows four different types of con-straints. In part a of the figure, point A of the rigid body is fixedby the two links and cannot move, and the third link preventsany rotation about A. Thus, this body is completely fixed withthree adequate (proper) constraints.

In part b of the figure, the third link is positioned so that theforce transmitted by it passes through point A where the othertwo constraint forces act. Thus, this configuration of constraintscan offer no initial resistance to rotation about A, which wouldoccur when external loads were applied to the body. We conclude,therefore, that this body is incompletely fixed under partialconstraints.

The configuration in part c of the figure gives us a similarcondition of incomplete fixity because the three parallel linkscould offer no initial resistance to a small vertical movement ofthe body as a result of external loads applied to it in this direction.The constraints in these two examples are often termed improper.

In part d of Fig. 3/7 we have a condition of complete fixity,with link 4 acting as a fourth constraint which is unnecessary tomaintain a fixed position. Link 4, then, is a redundant constraint,and the body is statically indeterminate.

As in the four examples of Fig. 3/7, it is generally possible bydirect observation to conclude whether the constraints on a bodyin two-dimensional equilibrium are adequate (proper), partial(improper), or redundant. As indicated previously, the vast ma-jority of problems in this book are statically determinate withadequate (proper) constraints.

Problem Solution

The sample problems at the end of this article illustrate theapplication of free-body diagrams and the equations of equilib-rium to typical statics problems. These solutions should be stud-ied thoroughly. In the problem work of this chapter andthroughout mechanics, it is important to develop a logical andsystematic approach which includes the following steps:

1. Identify clearly the quantities which are known and unknown.

2. Make an unambiguous choice of the body (or system of connected-bodies treated as a single body) to be isolated and draw its com-plete free-body diagram, labeling all external known and unknownbut identifiable forces and couples which act on it.

Art ic le 3/2 System Isolat ion and the Free-Body Diagram 21

p11 6191a_ch03 dm_21 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

A

4

A

Complete fixityAdequate constraints

(a)

Excessive fixityRedundant constraint

(d)

Incomplete fixityPartial constraints

(c)

A

Incomplete fixityPartial constraints

(b)

Figure 3/7

Page 22: Estic merian 6th-chapter 3_equilibrium

3. Choose a convenient set of reference axes, always using right-handed axes when vector cross products are employed. Choose mo-ment centers with a view to simplifying the calculations.Generally the best choice is one through which as many unknownforces pass as possible. Simultaneous solutions of equilibriumequations are frequently necessary, but can be minimized oravoided by a careful choice of reference axes and moment centers.

4. Identify and state the applicable force and moment principles orequations which govern the equilibrium conditions of the problem.In the following sample problems these relations are shown inbrackets and precede each major calculation.

5. Match the number of independent equations with the number ofunknowns in each problem.

6. Carry out the solution and check the results. In many problemsengineering judgment can be developed by first making a reason-able guess or estimate of the result prior to the calculation andthen comparing the estimate with the calculated value.

22 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_22 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Page 23: Estic merian 6th-chapter 3_equilibrium

Sample Problem 3/1

Determine the magnitudes of the forces C and T, which, along with the otherthree forces shown, act on the bridge-truss joint.

Solution. The given sketch constitutes the free-body diagram of the isolatedsection of the joint in question and shows the five forces which are in equilibrium.

Solution I (scalar algebra). For the x-y axes as shown we have

[oFx 5 0] 8 1 T cos 407 1 C sin 207 2 16 5 0

0.766T 1 0.342C 5 8 (a)

[oFy 5 0] T sin 407 2 C cos 207 2 3 5 0

0.643T 2 0.940C 5 3 (b)

Simultaneous solution of Eqs. (a) and (b) produces

T 5 9.09 kN C 5 3.03 kN Ans.

Solution II (scalar algebra). To avoid a simultaneous solution, we may useaxes x9-y9 with the first summation in the y9-direction to eliminate reference toT. Thus,

5 0][oF 9y 2C cos 207 2 3 cos 407 2 8 sin 407 1 16 sin 407 5 0

C 5 3.03 kN Ans.

5 0][oF 9x T 1 8 cos 407 2 16 cos 407 2 3 sin 407 2 3.03 sin 207 5 0

T 5 9.09 kN Ans.

Solution III (vector algebra). With unit vectors i and j in the x- and y-direc-tions, the zero summation of forces for equilibrium yields the vector equation

[oF 5 0] 8i 1 (T cos 407)i 1 (T sin 407)j 2 3j 1 (C sin 207)i

2 (C cos 207)j 2 16i 5 0

Equating the coefficients of the i- and j-terms to zero gives

8 1 T cos 407 1 C sin 207 2 16 5 0

T sin 407 2 3 2 C cos 207 5 0

which are the same, of course, as Eqs. (a) and (b), which we solved above.

Solution IV (geometric). The polygon representing the zero vector sum of thefive forces is shown. Equations (a) and (b) are seen immediately to give the pro-jections of the vectors onto the x- and y-directions. Similarly, projections onto thex9- and y9-directions give the alternative equations in Solution II.

A graphical solution is easily obtained. The known vectors are laid off head-to-tail to some convenient scale, and the directions of T and C are then drawnto close the polygon. The resulting intersection at point P completes the solution,thus enabling us to measure the magnitudes of T and C directly from the drawingto whatever degree of accuracy we incorporate in the construction.

Art ic le 3/3 Equi l ibr ium Condi t ions 23

p11 6191a_ch03 dm_23 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Helpful Hints

va Since this is a problem of concurrentforces, no moment equation isnecessary.

vb The selection of reference axes to fa-cilitate computation is always an im-portant consideration. Alternativelyin this example we could take a setof axes along and normal to the di-rection of C and employ a force sum-mation normal to C to eliminate it.

x′

T

x

y

y′

16 kN

3 kN

C

8 kN40°

20°

va

vb

vc

40°

20°

3 kN

8 kN

P

TC

16 kN

vc The known vectors may be added inany order desired, but they must beadded before the unknown vectors.

Page 24: Estic merian 6th-chapter 3_equilibrium

Sample Problem 3/2

Calculate the tension T in the cable which supports the 1000-lb load withthe pulley arrangement shown. Each pulley is free to rotate about its bearing,and the weights of all parts are small compared with the load. Find the magni-tude of the total force on the bearing of pulley C.

Solution. The free-body diagram of each pulley is drawn in its relative positionto the others. We begin with pulley A, which includes the only known force. Withthe unspecified pulley radius designated by r, the equilibrium of moments aboutits center O and the equilibrium of forces in the vertical direction require

[oM 5 0] T r 2 T r 5 0 T 5 TO 1 2 1 2

[oF 5 0] T 1 T 2 1000 5 0 2T 5 1000 T 5 T 5 500 lby 1 2 1 1 2

From the example of pulley A we may write the equilibrium of forces on pulleyB by inspection as

T 5 T 5 T /2 5 250 lb3 4 2

For pulley C the angle u 5 307 in no way affects the moment of T about the centerof the pulley, so that moment equilibrium requires

T 5 T or T 5 250 lb Ans.3

Equilibrium of the pulley in the x- and y-directions requires

[oF 5 0] 250 cos 307 2 F 5 0 F 5 217 lbx x x

[oF 5 0] F 1 250 sin 307 2 250 5 0 F 5 125 lby y y

2 2 2 2[F 5 ! ] F 5 ! 5 250 lb Ans.F 1 F (217) 1 (125)x y

24 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_24 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Sample Problem 3/3

The uniform 100-kg I-beam is supported initially by its end rollers on thehorizontal surface at A and B. By means of the cable at C it is desired to elevateend B to a position 3 m above end A. Determine the required tension P, thereaction at A, and the angle u made by the beam with the horizontal in theelevated position.

Solution. In constructing the free-body diagram, we note that the reaction onthe roller at A and the weight are vertical forces. Consequently, in the absenceof other horizontal forces, P must also be vertical. From Sample Problem 3/2 wesee immediately that the tension P in the cable equals the tension P applied tothe beam at C.

Moment equilibrium about A eliminates force R and gives

P(6 cos u) 2 981(4 cos u) 5 0 P 5 654 N Ans.[oMA 5 0]

Equilibrium of vertical forces requires

654 1 R 2 981 5 0 R 5 327 N Ans.[oFy 5 0]

The angle u depends only on the specified geometry and is

sin u 5 3/8 u 5 22.07 Ans.

A

B

C = 30°θ

T

1000 lb

va

A

B

C

T30°

O

T1T2

T3T4

Fy

Fx

1000 lb

y

x

Helpful Hints

va Clearly theradiusrdoesnotinfluencethe results. Once we have analyzed asimple pulley, the results should beperfectly clear by inspection.

Helpful Hints

va Clearly the equilibrium of this par-allel force system is independent of u.

va

P

CA B

2 m6 m

C

P

A

R

B2 m

2 m

100 (9.81) N4 m 3 m

y

Page 25: Estic merian 6th-chapter 3_equilibrium

Sample Problem 3/4

Determine the magnitude T of the tension in the supporting cable and themagnitude of the force on the pin at A for the jib crane shown. The beam AB isa standard 0.5-m I-beam with a mass of 95 kg per meter of length.

Algebraic solution. The system is symmetrical about the vertical x-y planethrough the center of the beam, so the problem may be analyzed as the equilib-rium of a coplanar force system. The free-body diagram of the beam is shown inthe figure with the pin reaction at A represented in terms of its two rectangularcomponents. The weight of the beam is 95(1023)(5)9.81 5 4.66 kN and actsthrough its center. Note that there are three unknowns Ax, Ay, and T which maybe found from the three equations of equilibrium. We begin with a moment equa-tion about A, which eliminates two of the three unknowns from the equation. Inapplying the moment equation about A, it is simpler to consider the moments ofthe x- and y-components of T than it is to compute the perpendicular distancefrom T to A. Hence, with the counterclockwise sense as positive we write

(T cos 257)0.25 1 (T sin 257)(5 2 0.12)[oMA 5 0]

2 10(5 2 1.5 2 0.12) 2 4.66(2.5 2 0.12) 5 0

T 5 19.61 kN Ans.from which

Equating the sums of forces in the x- and y-directions to zero gives

[oF 5 0] A 2 19.61 cos 257 5 0 A 5 17.77 kNx x x

[oF 5 0] A 1 19.61 sin 257 2 4.66 2 10 5 0 A 5 6.37 kNy y y

2 2 2 2[A 5 ! ] A 5 ! A 5 18.88 kN Ans.A 1 A (17.77) 1 (6.37)x y

Graphical solution. The principle that three forces in equilibrium must beconcurrent is utilized for a graphical solution by combining the two known ver-tical forces of 4.66 and 10 kN into a single 14.66-kN force, located as shown onthe modified free-body diagram of the beam in the lower figure. The position ofthis resultant load may easily be determined graphically or algebraically. Theintersection of the 14.66-kN force with the line of action of the unknown tensionT defines the point of concurrency O through which the pin reaction A must pass.The unknown magnitudes of T and A may now be found by adding the forceshead-to-tail to form the closed equilibrium polygon of forces, thus satisfying theirzero vector sum. After the known vertical load is laid off to a convenient scale,as shown in the lower part of the figure, a line representing the given directionof the tension T is drawn through the tip of the 14.66-kN vector. Likewise a linerepresenting the direction of the pin reaction A, determined from the concurrencyestablished with the free-body diagram, is drawn through the tail of the 14.66-kN vector. The intersection of the lines representing vectors T and A establishesthe magnitudes T and A necessary to make the vector sum of the forces equal tozero. These magnitudes are scaled from the diagram. The x- and y-componentsof A may be constructed on the force polygon if desired.

Art ic le 3/3 Equi l ibr ium Condi t ions 25

p11 6191a_ch03 dm_25 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Helpful Hints

va The justification for this step isVarig-non’s theorem, explained in Art. 2/4.Be prepared to take full advantage ofthisprinciple frequently.

vb The calculation of moments in two-dimensional problems is generallyhandled more simply by scalar alge-bra than by the vector cross productr3F. Inthreedimensions,asweshallsee later, the reverse is often the case.

vc The direction of the force at A couldbeeasily calculated if desired. However,in designing the pin A or in checkingits strength, it is only the magnitudeof the force that matters.

10 kN

25°A0.5 m

0.25 m

0.12 m

5 m

1.5 m

B

va

vb

vc

4.66 kN10 kN

25°

T

Ax

Ay

x

y

Free-Body Diagram

4.66 kN10 kN

14.66 kN

O

25°T

A

Ax

Ay

14.66 kN

T = 19.61 kN

A = 18.88 kN

Graphical Solution

Page 26: Estic merian 6th-chapter 3_equilibrium

PROBLEMS

Introductory Problems

3/1 The mass center G of the 1400-kg rear-engine car islocated as shown in the figure. Determine the normalforce under each tire when the car is in equilibrium.State any assumptions.

Ans. Nf 5 2820 N, Nr 5 4050 N

26 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_26 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/3 A carpenter holds a 12-lb 2-in. 3 4-in. board as shown.If he exerts vertical forces on the board, determine theforces at A and B.

Ans. NA 5 12 lb, NB 5 24 lb

G

1386 mm 964 mm

Problem 3/1

3/2 A carpenter carries a 12-lb 2-in. 3 4-in. board asshown. What downward force does he feel on his shoul-der at A?

5′

A B

2′ 1′

Problem 3/2

AB

6′2′

Problem 3/3

3/4 The 450-kg uniform I-beam supports the load shown.Determine the reactions at the supports.

5.6 m

220 kg

A B

2.4 m

Problem 3/4

3/5 The 20-kg homogeneous smooth sphere rests on thetwo inclines as shown. Determine the contact forces atA and B.

Ans. NA 5 101.6 N, NB 5196.2 N

A

B75° 30°

Problem 3/5

Page 27: Estic merian 6th-chapter 3_equilibrium

Art ic le 3/3 Problems 27

p11 6191a_ch03 dm_27 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/6 With what force magnitude T must the person pull onthe cable in order to cause the scale A to read 500 lb?The weights of the pulleys and cables are negligible.State any assumptions.

A

1000 lb

Problem 3/6

3/7 What horizontal force P must a worker exert on therope to position the 50-kg crate directly over thetrailer?

Ans. P 5 126.6 N

4 m

2 m

1 m

Problem 3/7

3/8 The 600-lb drum is being hoisted by the lifting devicewhich hooks over the end lips of the drum. Determinethe tension T in each of the equal-length rods whichform the two U-shaped members of the device.

10″

36″

A

B

C

Problem 3/8

3/9 What fraction n of the weight W of a jet airplane is thenet thrust (nozzle thrust T minus air resistance R) inorder for the airplane to climb with a constant speedat an angle u with the horizontal?

Ans. n 5 sin u

T

R

θ

Problem 3/9

3/10 Determine the force magnitude P required to lift oneend of the 250-kg crate with the lever dolly as shown.State any assumptions.

1500 mm

275 mm

250 kg

A

P

B

Problem 3/10

Page 28: Estic merian 6th-chapter 3_equilibrium

28 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_28 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/12 Determine the magnitude P of the vertical force re-quired to lift the wheelbarrow free of the ground atpoint B. The combined weight of the wheelbarrowand its load is 240 lb with center of gravity at G.

3/11 Find the angle of tilt u with the horizontal so that thecontact force at B will be one-half that at A for thesmooth cylinder.

Ans. u 5 18.437

A

45°

θ

45°

B

Problem 3/11

24″

A

CB

G

P

19″ 21″ 8″

20″

Problem 3/12

3/13 To facilitate shifting the position of a lifting hookwhen it is not under load, the sliding hanger shownis used. The projections at A and B engage theflanges of a box beam when a load is supported, andthe hook projects through a horizontal slot in thebeam. Compute the forces at A and B when the hooksupports a 300-kg mass.

Ans. A 5 4.91 kN, B 5 1.962 kN

400mm

600mm B

A

300 kg

Problem 3/13

3/14 Three cables are joined at the junction ring C. Deter-mine the tensions in cables AC and BC caused by theweight of the 30-kg cylinder.

15°

45°

30° 30 kg

A

B

CD

Problem 3/14

Page 29: Estic merian 6th-chapter 3_equilibrium

Art ic le 3/3 Problems 29

p11 6191a_ch03 dm_29 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/16 The uniform beam has a mass of 50 kg per meter oflength. Compute the reactions at the support O. Theforce loads shown lie in a vertical plane.

3/15 The 100-kg wheel rests on a rough surface and bearsagainst the roller A when the couple M is applied. IfM 5 60 N z m and the wheel does not slip, computethe reaction on the roller A.

Ans. FA 5 231 N

30°

300 mm

C

AM

Problem 3/15

30°

AO

BC3 kN

1.4 kN

4 kN·m

1.8 m0.6 m

0.6 m

0.6 m

Problem 3/16

3/17 To accommodate the rise and fall of the tide, a walk-way from a pier to a float is supported by two rollersas shown. If the mass center of the 300-kg walkwayis at G, calculate the tension T in the horizontal cablewhich is attached to the cleat and find the force underthe roller at A.

Ans. T 5 850 N, A 5 1472 N

G

30°

B

T

A

4 m

4 m

Problem 3/17

Page 30: Estic merian 6th-chapter 3_equilibrium

Representative Problems

3/18 Determine the magnitude P of the force which theman must exert perpendicular to the handle of thehigh-pressure washer in order to cause loss of contactat the front support B. Note that the operator pre-vents movement of the wheel with his left foot. The60-kg machine has its mass center at point G. Treatthe problem as two-dimensional.

30 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_30 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/20 The uniform 15-m pole has a mass of 150 kg and issupported by its smooth ends against the verticalwalls and by the tension T in the vertical cable. Com-pute the reactions at A and B.

310mm

30°

125mm

800 mm

B

A

G

O

P

Problem 3/18

3/19 If the screw B of the wood clamp is tightened so thatthe two blocks are under a compression of 500 N, de-termine the force in screw A. (Note: The force sup-ported by each screw may be taken in the directionof the screw.)

Ans. A 5 1250 N

100 mm150 mm

A B

Problem 3/19

A

B

5 m

10 m

12 m

T

Problem 3/20

3/21 Determine the force P required to begin rolling theuniform cylinder of mass m over the obstruction ofheight h.

Ans. P 52mg!2rh 2 h

r 2 h

rP

h

Problem 3/21

Page 31: Estic merian 6th-chapter 3_equilibrium

3/22 The elements of a heavy-duty fluid valve are shownin the figure. When the member OB rotates clockwiseabout the fixed pivot O under the action of the forceP, the element S slides freely upward in its slot, re-leasing the flow. If an internal torsional spring exertsa moment M 5 20 N z m as shown, determine theforce P required to open the valve. Neglect allfriction.

Art ic le 3/3 Problems 31

p11 6191a_ch03 dm_31 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/24 A block placed under the head of the claw hammeras shown greatly facilitates the extraction of the nail.If a 50-lb pull on the handle is required to pull thenail, calculate the tension T in the nail and the mag-nitude A of the force exerted by the hammer head onthe block. The contacting surfaces at A are suffi-ciently rough to prevent slipping.

180 mm

PM

B

O

A

S

Problem 3/22

3/23 The spring of modulus k 5 3.5 kN/m is stretched10 mm when the disk center O is in the leftmost po-sition x 5 0. Determine the tension T required to po-sition the disk center at x 5 150 mm. At that position,what force N is exerted on the horizontal slottedguide? The mass of the disk is 3 kg.

Ans. T 5 328 N, N 5 203 N (up)

x

O

T

45°

k = 3.5 kN/m

Problem 3/23

50 lb

8"

2"

1 ″A

20°

3–4

Problem 3/24

3/25 The indicated location of the center of gravity of the3600-lb pickup truck is for the unladen condition. Ifa load whose center of gravity is x 5 16 in. behindthe rear axle is added to the truck, determine theload weight WL for which the normal forces under thefront and rear wheels are equal.

Ans. WL 5 550 lb

45″ 67″ x

BA

GG

WL

Problem 3/25

Page 32: Estic merian 6th-chapter 3_equilibrium

3/26 To test the validity of aerodynamic assumptionsmade in the design of the aircraft, its model is beingtested in a wind tunnel. The support bracket is con-nected to a force and moment balance, which is ze-roed when there is no airflow. Under test conditions,the lift L, drag D, and pitching moment MG act asshown. The force balance records the lift, drag, anda moment MP. Determine MG in terms of L, D, andMP.

32 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_32 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/28 A person is performing slow arm curls with a 20-lbweight as indicated in the figure. The brachialis mus-cle group (consisting of the biceps and brachialismuscles) is the major factor in this exercise. Deter-mine the magnitude F of the brachialis-muscle-groupforce and the magnitude E of the elbow joint reactionat point E for the forearm position shown in the fig-ure. Take the dimensions shown to locate the effec-tive points of application of the two muscle groups;these points are 8 in. directly above E and 2 in. di-rectly to the right of E. Include the 3.2-lb forearmweight which acts at point G. State any assumptions.

d

h

Airflow

P

L

G

DMG

Problem 3/26

3/27 In a procedure to evaluate the strength of the tricepsmuscle, a person pushes down on a load cell with thepalm of his hand as indicated in the figure. If theload-cell reading is 35 lb, determine the vertical ten-sile force F generated by the triceps muscle. Thelower arm weighs 3.2 lb with mass center at G. Stateany assumptions.

Ans. F 5 401 lb

6″1″

6″

G

UlnaHand

Load cell

O

HumerusTriceps

Problem 3/27

EG

2″4″

14″

8″

HumerusBicepsBrachialis

UlnaRadius 20 lb

Problem 3/28

Page 33: Estic merian 6th-chapter 3_equilibrium

3/29 A woman is holding an 8-lb weight in her hand withthe entire arm held horizontally as shown in the fig-ure. A tensile force in the deltoid muscle prevents thearm from rotating about the shoulder joint O; thisforce acts at the 217 angle shown. Determine the forceexerted by the deltoid muscle on the upper arm at Aand the x- and y-components of the force reaction atthe shoulder joint O. The weight of the upper arm isWU 5 4.1 lb, the weight of the lower arm is WL 5 2.4lb, and the weight of the hand is WH 5 0.9 lb; all theseweights act at the locations shown in the figure.

Ans. FD 5 160.2 lb, Ox 5 149.5 lb, Oy 5 242.2 lb

Art ic le 3/3 Problems 33

p11 6191a_ch03 dm_33 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/30 With his weight W equally distributed on both feet,a man begins to slowly rise from a squatting positionas indicated in the figure. Determine the tensile forceF in the patellar tendon and the magnitude of theforce reaction at point O, which is the contact areabetween the tibia and the femur. Note that the lineof action of the patellar tendon force is along its mid-line. Neglect the weight of the lower leg.

y

x

5″

Deltoid muscle

21°

8 lb

WU

O

FD

A

WL WH

5.2″16.5″

25.4″

Problem 3/29

2″

9″

FemurFibula

TibiaPatella

Patellartendon

Quadriceps muscle

O

40°

55°

Problem 3/30

Page 34: Estic merian 6th-chapter 3_equilibrium

3/31 For the design of the belt-tensioning device, deter-mine the dimension l if the mass m maintains a spec-ified tension T in the belt for the position shown.Neglect the mass of the arm and central pulley com-pared with m. Also determine the magnitude R of theforce supported by the pin at O.

Ans. l 5 , R 5Tb!3 2 2 2!3T 1 m g

mg

34 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_34 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/33 The exercise machine is designed with a lightweightcart which is mounted on small rollers so that it isfree to move along the inclined ramp. Two cables areattached to the cart—one for each hand. If the handsare together so that the cables are parallel and if eachcable lies essentially in a vertical plane, determinethe force P which each hand must exert on its cablein order to maintain an equilibrium position. Themass of the person is 70 kg, the ramp angle u is 157,and the angle b is 187. In addition, calculate the forceR which the ramp exerts on the cart.

Ans. P 5 45.5 N, R 5 691 NT

T

l

30°b

O

G

m

30°

Problem 3/31

3/32 The uniform 18-kg bar OA is held in the positionshown by the smooth pin at O and the cable AB. De-termine the tension T in the cable and the magnitudeand direction of the external pin reaction at O.

B O

A

1.5 m

60°

1.2 m

Problem 3/32

β

θ

Problem 3/33

3/34 Calculate the magnitude of the force supported bythe pin at C under the action of the 900-N load ap-plied to the bracket. Neglect friction in the slot.

30°45°

B C

A15°

900 N

75 mm 150 mm

Problem 3/34

Page 35: Estic merian 6th-chapter 3_equilibrium

3/35 A uniform ring of mass m and radius r carries aneccentric mass m0 at a radius b and is in an equilib-rium position on the incline, which makes an anglea with the horizontal. If the contacting surfaces arerough enough to prevent slipping, write the expres-sion for the angle u which defines the equilibriumposition.

Ans. u 5 sin21 r m1 1 sin aF S D Gb m0

Art ic le 3/3 Problems 35

p11 6191a_ch03 dm_35 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

α

θ

m

r

Ob m0

Problem 3/35

3/36 The concrete hopper and its load have a combinedmass of 4 metric tons (1 metric ton equals 1000 kg)with mass center at G and is being elevated at con-stant velocity along its vertical guide by the cabletension T. The design calls for two sets of guide roll-ers at A, one on each side of the hopper, and two setsat B. Determine the force supported by each of thetwo pins at A and by each of the two pins at B.

T

10°

600 mm

300 mm

400 mm

C

G

A

B

Problem 3/36

3/37 During an engine test on the ground, a propellerthrust T 5 3000 N is generated on the 1800-kg air-plane with mass center at G. The main wheels at Bare locked and do not skid; the small tail wheel at Ahas no brake. Compute the percent change n in thenormal forces at A and B as compared with their ‘‘en-gine-off’’ values.

Ans. nA 5 232.6%, nB 5 2.28%

4 m

1.4 m

12°

T

G

BA0.8m

Problem 3/37

3/38 The elements of a wall-mounted swing-away stoolare shown in the figure. The hinge pin P fits looselythrough the frame tube, and the frame tube has aslight clearance between the supports A and B. De-termine the reactions on the frame tube at A and Bassociated with the weight L of an 80-kg person. Also,calculate the changes in the horizontal reactions atC and D due to the same load L. State anyassumptions.

350 mm

65 mm

CP

L

A

B

D

175 mm

65 mm

85 mm

Problem 3/38

Page 36: Estic merian 6th-chapter 3_equilibrium

36 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_36 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/40 In sailing at a constant speed with the wind, the sail-boat is driven by a 1000-lb force against its mainsailand a 400-lb force against its staysail as shown. Thetotal resistance due to fluid friction through the wa-ter is the force R. Determine the resultant of the lat-eral forces perpendicular to motion applied to thehull by the water.

3/39 The hook wrench or pin spanner is used to turnshafts and collars. If a moment of 80 N z m is requiredto turn the 200-mm-diameter collar about its centerO under the action of the applied force P, determinethe contact force R on the smooth surface at A. En-gagement of the pin at B may be considered to occurat the periphery of the collar.

Ans. R 5 1047 N

375 mmA

PB

O

120°100mm

Problem 3/39

5′

10′R

400 lb

1000 lb

Wind

Problem 3/40

3/41 A portion of the shifter mechanism for a manual cartransmission is shown in the figure. For the 4-lb forceexerted on the shift knob, determine the correspond-ing force P exerted by the shift link BC on the trans-mission (not shown). Neglect friction in theball-and-socket joint at O, in the joint at B, and inthe slip tube near support D. Note that a soft rubberbushing at D allows the slip tube to self-align withlink BC.

Ans. P 5 13.14 lb

7.5"

4 lb

15° Slip tube

A

B

O

D

C P3"

1"

1"

Problem 3/41

3/42 A torque (moment) of 24 N z m is required to turn thebolt about its axis. Determine P and the forces be-tween the smooth hardened jaws of the wrench andthe corners A and B of the hexagonal head. Assumethat the wrench fits easily on the bolt so that contactis made at corners A and B only.

AB14 mm

120 mm

P

Problem 3/42

Page 37: Estic merian 6th-chapter 3_equilibrium

Art ic le 3/3 Problems 37

p11 6191a_ch03 dm_37 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/44 Determine the external reactions at A and F for theroof truss loaded as shown. The vertical loads rep-resent the effect of the supported roofing materials,while the 400-N force represents a wind load.

3/43 The car complete with driver weighs 1700 lb andwithout the two airfoils has a 50%–50% front–rearweight distribution at a certain speed at which thereis no lift on the car. It is estimated that at this speedeach of the airfoils A1 and A2 will generate 400 lb ofdownward force L and 50 lb of drag force D on thecar. Specify the vertical reactions NA and NB underthe two pairs of wheels at that speed when the air-foils are added. Assume that the addition of the air-foils does not affect the drag and zero-lift conditionsof the car body itself and that the engine has suffi-cient power for equilibrium at that speed. The weightof the airfoils may be neglected.

Ans. NA 5 1201 lb (48.0%), NB 5 1299 lb (52.0%)

5"

32"120"A

A2

A1

B

D

L

Detail

Air flow

12"

38"

Problem 3/43

250 N

500 N

x

y

AG

F

B

C

D

E250 N

60°

60°

30° 30° 30°

400 N

500 N

500 N

10 m

Problem 3/44

3/45 Calculate the normal forces associated with the frontand rear wheel pairs of the 1600-kg front-wheel-drivevan. Then repeat the calculations when the van(a) climbs a 10-percent grade and (b) descends a 10-percent grade, both at constant speed. Compute thepercent changes nA and nB in the normal forces com-pared with the nominal values. Be sure to recognizethat propulsive and braking forces are present forcases (a) and (b).

Ans. NA 5 9420 N, NB 5 6280 N(a) N 5 9030 N (24.14%), N 5 6590 N (14.98%)A B

(b) N 5 9710 N (13.15%), N 5 5900 N (25.97%)A B

1200 mm 1800 mm

A

G

B

660 mm

Problem 3/45

3/46 It is desired that a person be able to begin closing thevan hatch from the open position shown with a 10-lbvertical force P. As a design exercise, determine thenecessary force in each of the two hydraulic strutsAB. The mass center of the 90-lb door is 1.5 in. di-rectly below point A. Treat the problem as two-dimensional.

45″

22″

Hinge axis

7″24″

Strut detail

30°A

A

O

O

B

B

P

Problem 3/46

Page 38: Estic merian 6th-chapter 3_equilibrium

38 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_38 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/48 The small crane is mounted on one side of the bed ofa pickup truck. For the position u 5 407, determinethe magnitude of the force supported by the pin at Oand the oil pressure p against the 50-mm-diameterpiston of the hydraulic cylinder BC.

3/47 The man pushes the lawn mower at a steady speedwith a force P that is parallel to the incline. The massof the mower with attached grass bag is 50 kg withmass center at G. If u 5 157, determine the normalforces NB and NC under each pair of wheels B and C.Neglect friction. Compare with the normal forces forthe conditions of u 5 0 and P 5 0.

Ans. NB 5 214 N, NC 5 260 NWith u 5 P 5 0: NB 5 350 N, NC 5 140.1 N

θ

900mm

1000mm

200mm

500mm

215 mmPA

G

C

B

Problem 3/47

B

C

A

θ

785mm

340mm

360mm

110mm

O120 kg

Problem 3/48

3/49 The pin A, which connects the 200-kg steel beam withcenter of gravity at G to the vertical column, iswelded both to the beam and to the column. To testthe weld, the 80-kg man loads the beam by exertinga 300-N force on the rope which passes through a holein the beam as shown. Calculate the torque (couple)M supported by the pin.

Ans. M 5 4.94 kN z m

GA

1200 mm 600mm

300 mm

Weldedpin

Problem 3/49

3/50 The cargo door for an airplane of circular fuselagesection consists of the uniform semicircular cowlingAB of mass m. Determine the compression C in thehorizontal strut at B to hold the door open in the po-sition shown. Also find an expression for the totalforce supported by the hinge at A. (Consult Table D/3of Appendix D for the position of the centroid or masscenter of the cowling.)

Light strut

Closed position of B

Horiz.

A

B

r

Problem 3/50

Page 39: Estic merian 6th-chapter 3_equilibrium

Art ic le 3/3 Problems 39

p11 6191a_ch03 dm_39 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/52 The rubber-tired tractor shown has a mass of 13.5Mg with center of mass at G and is used for pushingor pulling heavy loads. Determine the load P whichthe tractor can pull at a constant speed of 5 km/h upthe 15-percent grade if the driving force exertedby the ground on each of its four wheels is 80 percentof the normal force under that wheel. Also find thetotal normal reaction NB under the rear pair ofwheels at B.

3/51 The cargo door for an airplane of circular fuselagesection consists of the uniform quarter-circular seg-ment AB of mass m. A detent in the hinge at A holdsthe door open in the position shown. Determine themoment exerted by the hinge on the door.

Ans. MA 5 0.709mgr CCW

Closed position of B

Horiz. A

30°

B

r

Problem 3/51

A

1650 mm

P15100 1800 mm 1800 mm

B600 mm

600 mm

G

Problem 3/52

3/53 Pulley A delivers a steady torque (moment) of 900 lb-in. to a pump through its shaft at C. The tension inthe lower side of the belt is 150 lb. The driving motorB weighs 200 lb and rotates clockwise. As a designconsideration, determine the magnitude R of theforce on the supporting pin at O.

Ans. R 5 287 lb

150 lb

30°

3"

O

B

A

8″

5″ 5″

C 9"

Problem 3/53

3/54 The receiving unit for a wireless microphone system,exclusive of the antenna, has a mass of 1100 gramswith mass center at G. A single 375-g half-wave an-tenna with mass center at C is mounted to the re-ceiver at point O as shown. Plot the reaction forcesat A and B and their sum as functions of the antennaangle u over the range 0 # u # 907. Physically in-terpret your plot. Treat the problem as two-dimensional.

θ

30mm

75mm

45mm 250

mm

750mm

60mm

15mm

30mm

C

D

OG

A B

Problem 3/54

Page 40: Estic merian 6th-chapter 3_equilibrium

40 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_40 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/56 When setting the anchor so that it will dig into thesandy bottom, the engine of the 80,000-lb cruiserwith center of gravity at G is run in reverse to pro-duce a horizontal thrust T of 500 lb. If the anchorchain makes an angle of 607 with the horizontal, de-termine the forward shift b of the center of buoyancyfrom its position when the boat is floating free. Thecenter of buoyancy is the point through which theresultant of the buoyant forces passes.

3/55 A slender rod of mass m1 is welded to the horizontaledge of a uniform semicylindrical shell of mass m2.Determine an expression for the angle u with the hor-izontal made by the diameter of the shell through m1.(Consult Table D/3 in Appendix D to locate the centerof gravity of the semicircular section.)

Ans. u 5 tan21 pm1

2m2

m2

r m1

θ

Problem 3/55

3′

24′

G

T

6′60°

Problem 3/56

1800

mm

O

30°

60°

A

B

700mm

Problem 3/57

3/57 The uniform 400-kg drum is mounted on a line ofrollers at A and a line of rollers at B. An 80-kg manmoves slowly a distance of 700 mm from the verticalcenterline before the drum begins to rotate. All roll-ers are perfectly free to rotate, except one of them atB which must overcome appreciable friction in itsbearing. Calculate the friction force F exerted by thatone roller tangent to the drum and find the magni-tude R of the force exerted by all rollers at A on thedrum for this condition.

Ans. F 5 305 N, R 5 3770 N

3/58 The pipe bender consists of two grooved pulleysmounted and free to turn on a fixed frame. The pipeis bent into the shape shown by a force P 5 60 lb.Calculate the forces supported by the bearings of thepulleys.

20"

1.050"

P

BA

6"

1"

13/4"

Problem 3/58

Page 41: Estic merian 6th-chapter 3_equilibrium

F

G1

Sacrum

L3L4L5

G2

L

Wu

50 mm300 mm

41°

25 mm

Problem 3/60

Art ic le 3/3 Problems 41

p11 6191a_ch03 dm_41 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

c 3/60 The lumbar portion of the human spine supports theentire weight of the upper torso and the force loadimposed on it. We consider here the disk (shaded red)between the lowest vertebra of the lumbar region(L5) and the uppermost vertebra of the sacrum re-gion. (a) For the case L 5 0, determine the compres-sive force C and the shear force S supported by thisdisk in terms of the body weight W. The weight Wuof the upper torso (above the disk in question) is 68%of the total body weight W and acts at G1. The ver-tical force F which the rectus muscles of the backexert on the upper torso acts as shown in the figure.(b) Repeat for the case when the person holds aweight of magnitude L 5 W/3 as shown. State anyassumptions.

Ans. (a) C 5 0.795W, S 5 0.636W(b) C 5 2.45W, S 5 1.532W

c 3/59 A special jig is designed to position large concretepipe sections (shown in gray) and consists of an 80-Mg sector mounted on a line of rollers at A and a lineof rollers at B. One of the rollers at B is a gear whichmeshes with a ring of gear teeth on the sector so asto turn the sector about its geometric center O. Whena 5 0, a counterclockwise torque of 2460 N z m mustbe applied to the gear at B to keep the assembly fromrotating. When a 5 307, a clockwise torque of 4680N z m is required to prevent rotation. Locate the masscenter G of the jig by calculating and u. Note thatrthe mass center of the pipe section is at O.

Ans. 5 367 mm, u 5 79.87r

θα

Horiz O

G

–r

A B

5 m

Dia. = 480 mm

Problem 3/59

Page 42: Estic merian 6th-chapter 3_equilibrium

42 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_42 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

S E C T I O N B E Q U I L I B R I U M I N T H R E E D I M E N S I O N S

3/4 EQUILIBRIUM CONDITIONS

We now extend our principles and methods developed for two-dimensional equilibrium to the case of three-dimensional equilib-rium. In Art. 3/1 the general conditions for the equilibrium of abody were stated in Eqs. 3/1, which require that the resultantforce and resultant couple on a body in equilibrium be zero. Thesetwo vector equations of equilibrium and their scalar componentsmay be written as

oF 5 0x

oF 5 0 or oF 5 0y5oF 5 0z (3/3)

oM 5 0x

oM 5 0 or oM 5 0y5oM 5 0z

The first three scalar equations state that there is no resultantforce acting on a body in equilibrium in any of the three coordi-nate directions. The second three scalar equations express thefurther equilibrium requirement that there be no resultant mo-ment acting on the body about any of the coordinate axes or aboutaxes parallel to the coordinate axes. These six equations are bothnecessary and sufficient conditions for complete equilibrium. Thereference axes may be chosen arbitrarily as a matter of conve-nience, the only restriction being that a right-handed coordinatesystem should be chosen when vector notation is used.

The six scalar relationships of Eqs. 3/3 are independent con-ditions because any of them can be valid without the others. Forexample, for a car which accelerates on a straight and level roadin the x-direction, Newton’s second law tells us that the resultantforce on the car equals its mass times its acceleration. Thus,oFx Þ 0, but the remaining two force–equilibrium equations aresatisfied because all other acceleration components are zero. Sim-ilarly, if the flywheel of the engine of the accelerating car is ro-tating with increasing angular speed about the x-axis, it is not inrotational equilibrium about this axis. Thus, for the flywheelalone, oMx Þ 0 along with oFx Þ 0, but the remaining four equi-librium equations for the flywheel would be satisfied for its mass-center axes.

In applying the vector form of Eqs. 3/3, we first express eachof the forces in terms of the coordinate unit vectors i, j, and k.For the first equation, oF 5 0, the vector sum will be zero onlyif the coefficients of i, j, and k in the expression are, respectively,zero. These three sums, when each is set equal to zero, yield pre-

Page 43: Estic merian 6th-chapter 3_equilibrium

cisely the three scalar equations of equilibrium, oFx 5 0, oFy 50, and oFz 5 0.

For the second equation, oM 5 0, where the moment summay be taken about any convenient point O, we express the mo-ment of each force as the cross product r 3 F, where r is theposition vector from O to any point on the line of action of theforce F. Thus oM 5 o(r 3 F) 5 0. When the coefficients of i, j,and k in the resulting moment equation are set equal to zero,respectively, we obtain the three scalar moment equationsoMx 5 0, oMy 5 0, and oMz 5 0.

Free-Body Diagrams

The summations in Eqs. 3/3 include the effects of all forceson the body under consideration. We learned in the previous ar-ticle that the free-body diagram is the only reliable method fordisclosing all forces and moments which should be included inour equilibrium equations. In three dimensions the free-bodydiagram serves the same essential purpose as it does in two di-mensions and should always be drawn. We have our choice eitherof drawing a pictorial view of the isolated body with all externalforces represented or of drawing the orthogonal projections of thefree-body diagram. Both representations are illustrated in thesample problems at the end of this article.

The correct representation of forces on the free-body diagramrequires a knowledge of the characteristics of contacting surfaces.These characteristics were described in Fig. 3/1 for two-dimen-sional problems, and their extension to three-dimensional prob-lems is represented in Fig. 3/8 for the most common situations offorce transmission. The representations in both Figs. 3/1 and 3/8will be used in three-dimensional analysis.

The essential purpose of the free-body diagram is to developa reliable picture of the physical action of all forces (and couplesif any) acting on a body. So it is helpful to represent the forces intheir correct physical sense whenever possible. In this way, thefree-body diagram becomes a closer model to the actual physicalproblem than it would be if the forces were arbitrarily assignedor always assigned in the same mathematical sense as that of theassigned coordinate axis.

For example, in part 4 of Fig. 3/8, the correct sense of theunknowns Rx and Ry may be known or perceived to be in the senseopposite to those of the assigned coordinate axes. Similar condi-tions apply to the sense of couple vectors, parts 5 and 6, wheretheir sense by the right-hand rule may be assigned opposite tothat of the respective coordinate direction. By this time, youshould recognize that a negative answer for an unknown force orcouple vector merely indicates that its physical action is in thesense opposite to that assigned on the free-body diagram. Fre-quently, of course, the correct physical sense is not known ini-tially, so that an arbitrary assignment on the free-body diagrambecomes necessary.

Art ic le 3/4 Equi l ibr ium Condi t ions 43

p11 6191a_ch03 dm_43 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Page 44: Estic merian 6th-chapter 3_equilibrium

44 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_44 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

M O D E L I N G T H E A C T I O N O F F O R C E S I N T H R E E - D I M E N S I O N A L A N A L Y S I S

Type of Contact and Force Origin Action on Body to be Isolated

Force must be normal to thesurface and directed towardthe member.

The possibility exists for a force F tangent to the surface(friction force) to act on themember, as well as a normalforce N.

A lateral force P exerted by theguide on the wheel can exist, inaddition to the normal force N.

A ball-and-socket joint free topivot about the center of theball can support a force R withall three components.

In addition to three componentsof force, a fixed connectioncan support a couple Mrepresented by its threecomponents.

Thrust bearing is capable ofsupporting axial force Ry aswell as radial forces Rx and Rz.Couples Mx and Mz must, insome cases, be assumed zeroin order to provide staticaldeterminacy.

1. Member in contact with smoothsurface, or ball-supported member

2. Member in contactwith roughsurface

3. Roller or wheel supportwith lateralconstraint

4. Ball-and-socket joint

5. Fixed connection (embedded or welded)

6. Thrust-bearing support

z

x yN

z

x yN

z

x y

z

x y N

P

z

x y

z

x y

Ry

Rz

Rx

F

z

x y

z

x y

z

x y

z

y

RyMy

MzMx

Rz

Rx

x

z

yx

z

y

Ry

Mz

Rz

Rx

x

z

yx

Mx

Figure 3/8

Page 45: Estic merian 6th-chapter 3_equilibrium

Categories of Equilibrium

Application of Eqs. 3/3 falls into four categories which weidentify with the aid of Fig. 3/9. These categories differ in thenumber and type (force or moment) of independent equilibriumequations required to solve the problem.

Category 1, equilibrium of forces all concurrent at point O,requires all three force equations, but no moment equations be-cause the moment of the forces about any axis through O is zero.

Category 2, equilibrium of forces which are concurrent witha line, requires all equations except the moment equation aboutthat line, which is automatically satisfied.

Category 3, equilibrium of parallel forces, requires only oneforce equation, the one in the direction of the forces (x-directionas shown), and two moment equations about the axes (y and z)which are normal to the direction of the forces.

Art ic le 3/4 Equi l ibr ium Condi t ions 45

p11 6191a_ch03 dm_45 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

CATEGORIES OF EQUILIBRIUM IN THREE DIMENSIONS

Force System Free-Body Diagram Independent Equations

ΣFx = 0

ΣFy = 0

ΣMx = 0

ΣMy = 0

ΣFz = 0 ΣMz = 0

ΣFx = 0 ΣMy = 0

ΣMz = 0

ΣFx = 0

ΣFy = 0

ΣMy = 0

ΣMz = 0

ΣFz = 0

ΣFx = 0

ΣFy = 0

ΣFz = 0

1. Concurrent at a point

2. Concurrent with a line

3. Parallel

4. General

O

F1 F2

F3

F4

F4

F1

F2

F3

F5

F5

F5

F4

F4

F3

F1

F2 M

F1

F2

F3

y

x

z

yx

z

y

x

z

y

x

z

Figure 3/9

Page 46: Estic merian 6th-chapter 3_equilibrium

Category 4, equilibrium of a general system of forces, re-quires all three force equations and all three moment equations.

The observations contained in these statements are generallyquite evident when a given problem is being solved.

Constraints and Statical Determinacy

The six scalar relations of Eqs. 3/3, although necessaryand sufficient conditions to establish equilibrium, do not neces-sarily provide all of the information required to calculate the un-known forces acting in a three-dimensional equilibrium situation.Again, as we found with two dimensions, the question of ade-quacy of information is decided by the characteristics of the con-straints provided by the supports. An analytical criterion fordetermining the adequacy of constraints is available, but it isbeyond the scope of this treatment.* In Fig. 3/10, however, wecite four examples of constraint conditions to alert the reader tothe problem.

Part a of Fig. 3/10 shows a rigid body whose corner point A iscompletely fixed by the links 1, 2, and 3. Links 4, 5, and 6 preventrotations about the axes of links 1, 2, and 3, respectively, so thatthe body is completely fixed and the constraints are said to beadequate. Part b of the figure shows the same number of con-straints, but we see that they provide no resistance to a momentwhich might be applied about axis AE. Here the body is incom-pletely fixed and only partially constrained.

Similarly, in Fig. 3/10c the constraints provide no resistanceto an unbalanced force in the y-direction, so here also is a case ofincomplete fixity with partial constraints. In Fig. 3/10d, if a sev-enth constraining link were imposed on a system of six con-straints placed properly for complete fixity, more supports wouldprovided than would be necessary to establish the equilibriumposition, and link 7 would be redundant. The body would then bestatically indeterminate with such a seventh link in place. Withonly a few exceptions, the supporting constraints for rigid bodiesin equilibrium in this book are adequate, and the bodies are stat-ically determinate.

46 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_46 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

5

1

2 3

6

7

4

DC

BA

(a) Complete fixity Adequate constraints

(d) Excessive fixity Redundant constraint

E

y

A

(b) Incomplete fixity Partial constraints

(c) Incomplete fixity Partial constraints

Figure 3/10

*See the first author’s Statics, 2nd Edition SI Version 1975, Art. 16.

Page 47: Estic merian 6th-chapter 3_equilibrium

Sample Problem 3/5

The uniform 7-m steel shaft has a mass of 200 kg and is supported by a ball-and-socket joint at A in the horizontal floor. The ball end B rests against thesmooth vertical walls as shown. Compute the forces exerted by the walls and thefloor on the ends of the shaft.

Solution. The free-body diagram of the shaft is first drawn where the contactforces acting on the shaft at B are shown normal to the wall surfaces. In additionto the weight W 5 mg 5 200(9.81) 5 1962 N, the force exerted by the floor onthe ball joint at A is represented by its x-, y-, and z-components. These compo-nents are shown in their correct physical sense, as should be evident from therequirement that A be held in place. The vertical position of B is found from 7 5

, h 5 3 m. Right-handed coordinate axes are assigned as shown.2 2 2!2 1 6 1 h

Vector solution. We will use A as a moment center to eliminate reference tothe forces at A. The position vectors needed to compute the moments about Aare

r 5 21i 2 3j 1 1.5k m and r 5 22i 2 6j 1 3k mAG AB

where the mass center G is located halfway between A and B.The vector moment equation gives

r 3 (B 1 B ) 1 r 3 W 5 0AB x y AG[oMA 5 0]

(22i 2 6j 1 3k) 3 (B i 1 B j) 1 (2i 2 3j 1 1.5k) 3 (21962k) 5 0x y

i j k i j k

22 26 3 1 21 23 1.5 5 0* * * *B B 0 0 0 21962x y

(23B 1 5890)i 1 (3B 2 1962)j 1 (22B 1 6B )k 5 0y x y x

Equating the coefficients of i, j, and k to zero and solving give

B 5 654 N and B 5 1962 N Ans.x y

The forces at A are easily determined by

(654 2 A )i 1 (1962 2 A )j 1 (21962 1 A )k 5 0x y z[oF 5 0]

A 5 654 N A 5 1962 N A 5 1962 Nx y zand

Finally 2 2 2A 5 !A 1 A 1 Ax y z

2 2 25 ! 5 2850 N Ans.(654) 1 (1962) 1 (1962)

Scalar solution. Evaluating the scalar moment equations about axes throughA parallel, respectively, to the x- and y-axes, gives

[oM 5 0]Ax

[oM 5 0]Ay

1962(3) 2 3B 5 0 B 5 1962 Ny y

21962(1) 1 3B 5 0 B 5 654 Nx x

The force equations give, simply,

[oF 5 0]x

[oF 5 0]y

[oF 5 0]z

2A 1 654 5 0 A 5 654 Nx x

2A 1 1962 5 0 A 5 1962 Ny y

A 2 1962 5 0 A 5 1962 Nz z

Art ic le 3/4 Equi l ibr ium Condi t ions 47

p11 6191a_ch03 dm_47 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

7 m

6 m 2 m

B

A

Helpful Hints

va We could, of course, assign all of theunknown components of force in thepositive mathematical sense, inwhich case Ax and Ay would turn outto be negative upon computation.Thefree-body diagram describes thephysical situation, so it is generallypreferable to show the forces in theircorrect physical senses whereverpossible.

vb Note that the third equation 22By 16Bx 5 0 merely checks the results ofthe first two equations. This resultcould be anticipated from the factthat an equilibrium system of forcesconcurrent with a line requires onlytwo moment equations (Category 2under Categories of Equilibrium).

vc We observe that a moment sumaboutan axis through A parallel to the z-axis merely gives us 6Bx 2 2By 5 0,which serves only as a check as notedpreviously. Alternatively we couldhave first obtained Az from oFz 5 0and then taken our moment equa-tions about axes through B to obtainAx and Ay.

6 m

3.5 m

3.5 m

2 mA

B

G

y

h

x

z

W = mg

Ax

ByBx

Ay

Az

va

vb

vc

Page 48: Estic merian 6th-chapter 3_equilibrium

Sample Problem 3/6

A 200-N force is applied to the handle of the hoist in the direction shown.The bearing A supports the thrust (force in the direction of the shaft axis), whilebearing B supports only radial load (load normal to the shaft axis). Determinethe mass m which can be supported and the total radial force exerted on theshaft by each bearing. Assume neither bearing to be capable of supporting amoment about a line normal to the shaft axis.

Solution. The system is clearly three-dimensional with no lines or planes ofsymmetry, and therefore the problem must be analyzed as a general space sys-tem of forces. A scalar solution is used here to illustrate this approach, althougha solution using vector notation would also be satisfactory. The free-body dia-gram of the shaft, lever, and drum considered a single body could be shown by aspace view if desired, but is represented here by its three orthogonal projections.

The 200-N force is resolved into its three components, and each of the threeviews shows two of these components. The correct directions of Ax and Bx maybe seen by inspection by observing that the line of action of the resultant of thetwo 70.7-N forces passes between A and B. The correct sense of the forces Ay andBy cannot be determined until the magnitudes of the moments are obtained, sothey are arbitrarily assigned. The x-y projection of the bearing forces is shownin terms of the sums of the unknown x- and y-components. The addition of Azand the weight W 5 mg completes the free-body diagrams. It should be notedthat the three views represent three two-dimensional problems related by thecorresponding components of the forces.

From the x-y projection

100(9.81m) 2 250(173.2) 5 0 m 5 44.1 kg Ans.[oMO 5 0]

From the x-z projection

[oMA 5 0] 150Bx 1 175(70.7) 2 250(70.7) 5 0 Bx 5 35.4 N

[oFx 5 0] Ax 1 35.4 2 70.7 5 0 Ax 5 35.4 N

The y-z view gives

[oMA 5 0] 150By 1 175(173.2) 2 250(44.1)(9.81) 5 0 By 5 520 N

[oFy 5 0] Ay 1 520 2 173.2 2 (44.1)(9.81) 5 0 Ay 5 86.8 N

[oFz 5 0] Az 5 70.7 N

The total radial forces on the bearings become

[Ar 5 2 2! ]A 1 Ax y Ar 5 5 93.5 N2 2!(35.4) 1 (86.8) Ans.

[B 5 2 2! ]B 1 Bx y B 5 5 521 N2 2!(35.4) 1 (520) Ans.

48 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_48 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Thrustbearing

Radialbearing

100 45°

60°

200 N75150100

100 250

x

z

y

A

B

m

Dimensions in millimeters

70.7 N

173.2 N 173.2 N

70.7 N

70.7 N

70.7 N

Az

Az

Ax + Bx

Ay + By

Bx

z

x

Ax

By Ay

z x

yy

mg = 9.81m mg = 9.81m

O

Helpful Hints

va If the standard three views of ortho-graphic projection are not entirelyfamiliar, then review and practicethem. Visualize the three views asthe images of the body projected ontothe front, top, and end surfaces of aclear plastic box placed over andaligned with the body.

vb We could have started with the x-zprojection rather than with the x-yprojection.

vc The y-z view could have followed im-mediately after the x-y view since thedetermination of Ay and By may bemade after m is found.

vd Without the assumption of zero mo-ment supported by each bearingabout a line normal to the shaft axis,the problem would be staticallyindeterminate.

va

vb

vc

vd

Page 49: Estic merian 6th-chapter 3_equilibrium

Sample Problem 3/7

The welded tubular frame is secured to the horizontal x-y plane by a ball-and-socket joint at A and receives support from the loose-fitting ring at B. Underthe action of the 2-kN load, rotation about a line from A to B is prevented by thecable CD, and the frame is stable in the position shown. Neglect the weight ofthe frame compared with the applied load and determine the tension T in thecable, the reaction at the ring, and the reaction components at A.

Solution. The system is clearly three-dimensional with no lines or planes ofsymmetry, and therefore the problem must be analyzed as a general space sys-tem of forces. The free-body diagram is drawn, where the ring reaction is shownin terms of its two components. All unknowns except T may be eliminated by amoment sum about the line AB. The direction of AB is specified by the unit vector

n 5 (4.5j 1 6k) 5 (3j 1 4k). The moment of T about AB is the1 1

52 2!6 1 4.5component in the direction of AB of the vector moment about the point A andequals r1 3 T z n. Similarly the moment of the applied load F about AB isr2 3 F z n. With 5 m, the vector expressions for T, F, r1, and r2 areCD !46.2

TT 5 (2i 1 2.5j 2 6k) F 5 2j kN

!46.2

r 5 2i 1 2.5j m r 5 2.5i 1 6k m1 2

The moment equation now becomes

T 1[oM 5 0] (2i 1 2.5j) 3 (2i 1 2.5j 2 6k) z (3j 1 4k)AB 5!46.2

11 (2.5i 1 6k) 3 (2j) z (3j 1 4k) 5 05

Completion of the vector operations gives

48T2 1 20 5 0 T 5 2.83 kN Ans.

!46.2

and the components of T become

T 5 0.833 kN T 5 1.042 kN T 5 22.50 kNx y z

We may find the remaining unknowns by moment and force summations asfollows:

[oM 5 0]z

[oM 5 0]x

[oF 5 0]x

[oF 5 0]y

[oF 5 0]z

2(2.5) 2 4.5B 2 1.042(3) 5 0 B 5 0.417 kNx x

4.5B 2 2(6) 2 1.042(6) 5 0 B 5 4.06 kNz z

A 1 0.417 1 0.833 5 0 A 5 21.250 kNx x

A 1 2 1 1.042 5 0 A 5 23.04 kNy y

A 1 4.06 2 2.50 5 0 A 5 21.556 kNz z

Ans.

Ans.

Ans.

Ans.

Ans.

Art ic le 3/4 Equi l ibr ium Condi t ions 49

p11 6191a_ch03 dm_49 Tuesday Mar 13 2001 02:21 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Helpful Hints

va The advantage of using vector nota-tion in this problem is the freedom totake moments directly about anyaxis. In this problem this freedompermits the choice of an axis thateliminates five of the unknowns.

vb Recall that the vector r in the expres-sion r 3 F for the moment of a force isa vector from the moment center toany point on the line of action of theforce. Instead of r1, an equally simplechoicewouldbe the vectorAC

ˆl

.

vc The negative signs associated withthe A-components indicate that theyare in the opposite direction to thoseshownon the free-bodydiagram.

2.5 m

3 mz

x y

C

B

DA

6 m

4.5 m

2 kN

1 m

2.5 m

BxE

D

z

x y

F = 2 kN

r2

r1

T

n

z B

Ax y

n

Bz

Az

AxAy

r1 ×× T· n

r1 ×× T

va

vb

vc

Page 50: Estic merian 6th-chapter 3_equilibrium

PROBLEMS

Introductory Problems

3/61 A force of magnitude P 5 40 lb is applied to the sta-tionary machine handle as shown. Write the forceand moment reactions at O as vectors. Neglect theweight of the handle assembly.

Ans. R 5 238.6i 2 10.35k lbM 5 2103.5i 2 193.2j 1 386k lb-in.

50 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_50 Tuesday Mar 13 2001 03:12 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/63 Determine the tensions in cables AB, AC, and AD.Ans. TAB 5 47.8 lb, TAC 5 47.8 lb, TAD 5 31.2 lb

15°

10″

5″

z

PA

O

x

y

Problem 3/61

3/62 Three workers are carrying a 4-ft by 8-ft panel in thehorizontal position shown. If the homogeneous panelweighs 100 lb, estimate the lifting force exerted byeach worker.

1.2′

2.4′5.6′

2.4′

1.6′A C

B

Problem 3/62

3′

3′ 3′

1′

4′

100 lb

A

B

C

D

Problem 3/63

3/64 The uniform I-beam has a mass of 60 kg per meterof its length. Determine the tension in the two sup-porting cables and the reaction at D.

2 m

3 m

2 m

2 m

1 m

5 mA

D

C

B

Problem 3/64

Page 51: Estic merian 6th-chapter 3_equilibrium

3/65 The vertical mast supports the 4-kN force and is con-strained by the two fixed cables BC and BD and by aball-and-socket connection at A. Calculate the ten-sion T1 in BD. Can this be accomplished by usingonly one equation of equilibrium?

Ans. T1 5 4.90 kN

Art ic le 3/4 Problems 51

p11 6191a_ch03 dm_51 Tuesday Mar 13 2001 03:12 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/67 The light right-angle boom which supports the 400-kg cylinder is supported by three cables and a ball-and-socket joint at O attached to the vertical x-ysurface. Determine the reactions at O and the cabletensions.

Ans. Ox 5 1962 N, Oy 5 0, Oz 5 6540 NTAC 5 4810 N, TBD 5 2770 N, TBE 5 654 N

T1

T2

z

B

y

A

D

C5 m

5 m

5 m

4 kN 4 m

4 m

2 m

x

Problem 3/65

3/66 An overhead view of a car is shown in the figure. Twodifferent locations C and D are considered for a singlejack. In each case, the entire right side of the car islifted just off the ground. Determine the normal re-action forces at A and B and the vertical jacking forcerequired for the case of each jacking location. Con-sider the 1600-kg car to be rigid. The mass center Gis on the midline of the car.

1575 mm

BA

G

C D1120mm

1400mm 280

mm

Problem 3/66

400 kg

B

A

C

O

D

E

1 m

1 m

y

x

z

1.5 m

1 m

2 m

0.75 m0.75 m

Problem 3/67

3/68 The industrial door is a uniform rectangular panelweighing 1200 lb and rolls along the fixed rail D onits hanger-mounted wheels A and B. The door ismaintained in a vertical plane by the floor-mountedguide roller C, which bears against the bottom edge.For the position shown compute the horizontal sidethrust on each of the wheels A and B, which must beaccounted for in the design of the brackets.

6"

Detail ofDoor Hanger

D

A

C

z

y

x

3′

3′10′

10′

5′

B

Problem 3/68

Page 52: Estic merian 6th-chapter 3_equilibrium

3/69 A three-legged stool is subjected to the load L asshown. Determine the vertical force reaction undereach leg. Neglect the weight of the stool.

Ans. NA 5 0.533L, NB 5 NC 5 0.233L

52 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_52 Tuesday Mar 13 2001 03:12 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Representative Problems

3/71 The three-wheel truck is used to carry the 100-kg boxas shown. Calculate the changes in the normal forcereactions at the three wheels due to the weight of thebox.

Ans. DNA 5 66.1 N, DNB 5 393 NDNC 5 522 N

A

B

120° 120°

120°

325

Dimensions in millimeters

L

7575100

C

Problem 3/69

3/70 Calculate the compression P in each leg of the equi-lateral spreader frame ABC, which ensures the ap-plication of equal vertical forces to the rim of theconcrete hopper. The total load L is 840 lb. Note thatdetermination of P would be a first step in the designof the frame.

L

A B

C3′

3′

3′

4′

Problem 3/70

C

100 kgB

G

A

500 mm

375 mm625 mm550 mm

250 mm

Problem 3/71

3/72 One of the vertical walls supporting end B of the 200-kg uniform shaft of Sample Problem 3/5 is turnedthrough a 307 angle as shown here. End A is still sup-ported by the ball-and-socket connection in the hor-izontal x-y plane. Calculate the magnitudes of theforces P and R exerted on the ball end B of the shaftby the vertical walls C and D, respectively.

x y

z

BD

C

A

30°

6 m

7 m

2 m

Problem 3/72

Page 53: Estic merian 6th-chapter 3_equilibrium

3/73 The smooth homogeneous sphere rests in the 1207

groove and bears against the end plate which is nor-mal to the direction of the groove. Determine the an-gle u, measured from the horizontal, for which thereaction on each side of the groove equals the forcesupported by the end plate.

Ans. u 5 307

Art ic le 3/4 Problems 53

p11 6191a_ch03 dm_53 Tuesday Mar 13 2001 03:12 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/75 As part of a check on its design, a lower A-arm (partof an automobile suspension) is supported by bear-ings at A and B and subjected to the pair of 900-Nforces at C and D. The suspension spring, not shownfor clarity, exerts a force FS at E as shown, where Eis in plane ABCD. Determine the magnitude FS ofthe spring force and the magnitudes FA and FB of thebearing forces at A and B which are perpendicular tothe hinge axis AB.

Ans. FS 5 3950 N, FA 5 437 N, FB 5 2450 N

60°

60°

θHorizontal

End viewof V-groove

Problem 3/73

3/74 The mass center of the 30-kg door is in the center ofthe panel. If the weight of the door is supported en-tirely by the lower hinge A, calculate the magnitudeof the total force supported by the hinge at B.

1500 mm

80 mm 360 mm

30 kg

1640 mm

A

B

Problem 3/74

420 mm

900 N

900 N

15°Fs

170 mm

190 mm

180mm

120mm

A

C

E

B

D

Problem 3/75

3/76 Determine the magnitudes of the force R and coupleM exerted by the nut and bolt on the loaded bracketat O to maintain equilibrium.

200 mm

30°

50°

1.6 kN

200 mm

150 mm

O

z

2.4 kN

yx

Problem 3/76

Page 54: Estic merian 6th-chapter 3_equilibrium

3/77 The square steel plate has a mass of 1800 kg withmass center at its center G. Calculate the tension ineach of the three cables with which the plate is liftedwhile remaining horizontal.

Ans. TA 5 TB 5 5.41 kN, TC 5 9.87 kN

54 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_54 Tuesday Mar 13 2001 03:12 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/79 One of the three landing pads for a proposed Marslander is shown in the figure. As part of a designcheck on the distribution of force in the landingstruts, compute the force in each of the struts AC,BC, and CD when the lander is resting on a horizon-tal surface on Mars. The arrangement is symmeticalwith respect to the x-z plane. The mass of the landeris 600 kg. (Assume equal support by the pads andconsult Table D/2 in Appendix D as needed.)

Ans. FAC 5 FCB 5 240 N tensionFCD 5 1046 N compression

2400 mm 1200 mm

1200 mm

1200 mm

2400mm

G

C

B

A

D

Problem 3/77

3/78 During a test, the left engine of the twin-engine air-plane is revved up and a 500-lb thrust is generated.The main wheels at B and C are braked in order toprevent motion. Determine the change (comparedwith the nominal values with both engines off) in thenormal reaction forces at A, B, and C.

12′

7′7′

6′

C

T = 500 lb

B A

Problem 3/78

Dimensions in millimeters

550

350

550

300

300

100

A

x

y

z

B

D

C

Problem 3/79

3/80 The spring of modulus k 5 900 N/m is stretched adistance d 5 60 mm when the mechanism is in theposition shown. Calculate the force Pmin required toinitiate rotation about the hinge axis BC, and deter-mine the corresponding magnitudes of the bearingforces which are perpendicular to BC. What is thenormal reaction force at D if P 5 Pmin/2?

45 mm

45 mm

40 mm

k = 900 N/m

PA

B

C

D

55mm

55mm

90mm

135mm

135mm

165mm

Problem 3/80

Page 55: Estic merian 6th-chapter 3_equilibrium

3/81 A smooth homogeneous sphere of mass m and radiusr is suspended by a wire AB of length 2r from pointB on the line of intersection of the two smooth ver-tical walls at right angles to one another. Determinethe reaction R of each wall against the sphere.

Ans. R 5 mg/!7

Art ic le 3/4 Problems 55

p11 6191a_ch03 dm_55 Tuesday Mar 13 2001 03:12 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/83 The shaft, lever, and handle are welded together andconstitute a single rigid body. Their combined massis 28 kg with mass center at G. The assembly ismounted in bearings A and B, and rotation is pre-vented by link CD. Determine the forces exerted onthe shaft by bearings A and B while the 30-N z m cou-ple is applied to the handle as shown. Would theseforces change if the couple were applied to the shaftAB rather than to the handle?

Ans. A 5 167.9 N, B 5 117.1 N

2r

r

x

y

z

B

A

Problem 3/81

3/82 The uniform 15-kg plate is welded to the verticalshaft, which is supported by bearings A and B. Cal-culate the magnitude of the force supported by bear-ing B during application of the 120-N z m couple tothe shaft. The cable from C to D prevents the plateand shaft from turning, and the weight of the assem-bly is carried entirely by bearing A.

D

A

B

400 mm

600 mm

200 mm

80 mm

200 mm

120 N·m

C

Problem 3/82

30 N·m

y

x

z

B

A

C

D

450 mm

100 mm

G

200mm 200mm

220mm

300mm

600mm

300mm

Problem 3/83

Page 56: Estic merian 6th-chapter 3_equilibrium

3/85 The unit ABCD of the radial-arm saw weighs 40 lbwith center of gravity at G. If a horizontal 10-lb forceis applied to the control handle in sawing the board,calculate the corresponding bending moment actingon the column at A (total moment about a horizontalaxis through A). The reaction of the wood on the sawteeth is 15 lb in the direction shown, and to a closeapproximation, its point of application may be takenas E. What justification exists for treating the saw asbeing in equilibrium?

Ans. M 5 711 lb-in.

56 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_56 Tuesday Mar 13 2001 03:12 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

E

y

18°

6″

15 lb

z

C

10 lb 6″3″G

6″

B18″

16″

D

A

z

12″ yx

Problem 3/85

3/84 Consider the rudder assembly of a radio-controlledmodel airplane. For the 157 position shown in the fig-ure, the net pressure acting on the left side of therectangular rudder area is p 5 4(1025) N/mm2. De-termine the required force P in the control rod DEand the horizontal components of the reactions athinges A and B which are parallel to the rudder sur-face. Assume the aerodynamic pressure to beuniform.

15°

Dimensions inmillimeters

22

10 15°

32 16

B

AC

D

EP16

42

12

Problem 3/84

Page 57: Estic merian 6th-chapter 3_equilibrium

3/87 The upper ends of the vertical coil springs in thestock racecar can be moved up and down by meansof a screw mechanism not shown. This adjustmentpermits a change in the downward force at eachwheel as an optimum handling setup is sought. Ini-tially, scales indicate the normal forces to be 800 lb,800 lb, 1000 lb, and 1000 lb at A, B, C, and D, re-spectively. If the top of the right rear spring at A islowered so that the scale at A reads an additional 100lb, determine the corresponding changes in the nor-mal forces at B, C, and D. Neglect the effects of thesmall attitude changes (pitch and roll angles) causedby the spring adjustment. The front wheels are thesame distance apart as the rear wheels.Ans. DNB 5 2100 lb, DNC 5 100 lb, DND 5 2100 lb

Art ic le 3/4 Problems 57

p11 6191a_ch03 dm_57 Tuesday Mar 13 2001 03:12 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Simplified spring detail

A

B

C

D

Problem 3/87

3/86 The rigid pole and cross-arms of Prob. 2/95 are shownagain here. Determine the tensions TAE and TGF inthe two supporting cables resulting from the 1.2-kNtension in cable CD. Assume the absence of any re-sisting moments on the base of the pole at O aboutthe x- and y-axes, but not about the z-axis.

T = 1.2 kN

z'

y'

y

x'

x

z

B

C

G

A

E

D

F1 m

2 m

3 m

1.5 m

1.5 m

1.5 m

1 m

3 m

O

Problem 3/86

Page 58: Estic merian 6th-chapter 3_equilibrium

58 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_58 Tuesday Mar 13 2001 03:13 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

c 3/90 A rectangular sign over a store has a mass of 100 kg,with the center of mass in the center of the rectangle.The support against the wall at point C may betreated as a ball-and-socket joint. At corner D sup-port is provided in the y-direction only. Calculate thetensions T1 and T2 in the supporting wires, the totalforce supported at C, and the lateral force R sup-ported at D.

Ans. T1 5 347 N, T2 5 431 NR 5 63.1 N, C 5 768 N

4 m

1 m

2.5 m

1.5 m

1.5 m

2.5 m

1 m

x

D

B

A

T1 T2

Cy

z

Problem 3/90

3/89 The boom AB lies in the vertical y-z plane and is sup-ported by a ball-and-socket joint at B and by the twocables at A. Calculate the tension in each cable re-sulting from the 20-kN force acting in the horizontalplane and applied at the midpoint M of the boom.Neglect the weight of the boom.

Ans. T1 5 33.0 kN, T2 5 22.8 kN

xC

D

T1

T2

B

M

A

y

z

20 kN

10 m

3 m

2 m

2 m

4 m

4 m

20°

Problem 3/89

3/88 The uniform 30- by 40-in. trap door weighs 200 lb andis propped open by the light strut AB at the angleu 5 tan21 (4/3). Calculate the compression FB in thestrut and the force supported by the hinge D normalto the hinge axis. Assume that the hinges act at theextreme ends of the lower edge.

30″

A

C

D

B30″

32″8″

= tan–1θ 4—3

Problem 3/88

Page 59: Estic merian 6th-chapter 3_equilibrium

b

b/4

50°

C

D

A

B

a

y

z

x

Problem 3/91

c 3/92 The uniform rectangular panel ABCD has a mass of40 kg and is hinged at its corners A and B to the fixedvertical surface. A wire from E to D keeps edges BCand AD horizontal. Hinge A can support thrust alongthe hinge axis AB, whereas hinge B supports forcenormal to the hinge axis only. Find the tension T inthe wire and the magnitude B of the force supportedby hinge B.

Ans. T 5 277 N, B 5 169.9 N

Art ic le 3/4 Problems 59

p11 6191a_ch03 dm_59 Tuesday Mar 13 2001 03:13 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

2400 mm

1200 mm

30°

A

B

C

D

T

E

Problem 3/92

c 3/91 The awning window is temporarily held open in the507 position shown by a wooden prop CD until acrank-type opening mechanism can be installed. Ifa 5 0.8 m and b 5 1.2 m and the mass of the windowis 50 kg with mass center at its geometric center,determine the compressive force FCD in the prop andall components of the forces exerted by the hinges Aand B on the window. Assume that A is a thrust-bearing hinge but that hinge B is not.

Ans. Ax 5 2140.9 N, Ay 5 118.2 N, Az 5 292.0 NBx 5 247.0 N, By 5 285 N, FCD 5 227 N

Page 60: Estic merian 6th-chapter 3_equilibrium

60 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_60 Tuesday Mar 13 2001 03:13 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

c 3/94 The portable reel is used to wind up and store an airhose. The tension in the hose is 100 N and a vertical200-N force is applied to the handle in order to steadythe reel frame. Determine the force minimum Pwhich must be applied perpendicular to the handleDE and the vertical components of the force reactionsat the feet A, B, and C. The diameter of the coil ofreeled hose is 300 mm, and the weight of the loadedreel and its frame may be neglected. State anyassumptions.

Ans. P 5 50 N, NA 5 113.7 N,NB 5 37.5 N, NC 5 66.2 N

200 N

P

ED

O

B

A

C

150150 150

125

OD = 300 mm

375100 N

15°

30°

Dimensions in millimeters

525

500

Problem 3/94

c 3/93 Under the action of the 40-N z m torque (couple) ap-plied to the vertical shaft, the restraining cable AClimits the rotation of the arm OA and attached shaftto an angle of 607 measured from the y-axis. The col-lar D fastened to the shaft prevents downward mo-tion of the shaft in its bearing. Calculate the bendingmoment M, the compression P, and the shear force Vin the shaft at section B. (Note: Bending moment, ex-pressed as a vector, is normal to the shaft axis, andshear force is also normal to the shaft axis.)

Ans. M 5 47.7 N z m, P 5 320 N, V 5 274 N

110 mm

200 mm

180 mm

40 N·m

60°

160 mm A

O

z

xy

B

C

D

Problem 3/93

Page 61: Estic merian 6th-chapter 3_equilibrium

3/5 C H A P T E R R E V I E W

In Chapter 3 we have applied our knowledge of the properties offorces, moments, and couples studied in Chapter 2 to solve problemsinvolving rigid bodies in equilibrium. Complete equilibrium of a bodyrequires that the vector resultant of all forces acting on it be zero(oF 5 0) and the vector resultant of all moments on the body about apoint (or axis) also be zero (oM 5 0). We are guided in all of our solutionsby these two requirements, which are easily comprehended physically.

Frequently, it is not the theory but its application which presentsthe difficulty. The crucial steps in applying our principles of equilibriumshould be quite familiar by now. They are:

1. Make an unequivocal decision as to which system (a body or col-lection of bodies) in equilibrium is to be analyzed.

2. Isolate the system in question from all contacting bodies by draw-ing its free-body diagram showing all forces and couples acting onthe isolated system from external sources.

3. Observe the principle of action and reaction (Newton’s third law)when assigning the sense of each force.

4. Label all forces and couples, known and unknown.

5. Choose and label reference axes, always choosing a right-handedset when vector notation is used (which is usually the case forthree-dimensional analysis).

6. Check the adequacy of the constraints (supports) and match thenumber of unknowns with the number of available independentequations of equilibrium.

When solving an equilibrium problem, we should first check to seethat the body is statically determinate. If there are more supports thanare necessary to hold the body in place, the body is statically indeter-minate, and the equations of equilibrium by themselves will not enableus to solve for all of the external reactions. In applying the equations ofequilibrium, we choose scalar algebra, vector algebra, or graphical anal-ysis according to both preference and experience; vector algebra is par-ticularly useful for many three-dimensional problems.

The algebra of a solution can be simplified by the choice of a momentaxis which eliminates as many unknowns as possible or by the choice ofa direction for a force summation which avoids reference to certain un-knowns. A few moments of thought to take advantage of these simpli-fications can save appreciable time and effort.

The principles and methods covered in Chapters 2 and 3 constitutethe most basic part of statics. They lay the foundation for what followsnot only in statics but in dynamics as well.

Chapter Rev iew 61

p11 6191a_ch03 dm_61 Tuesday Mar 13 2001 03:13 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

Page 62: Estic merian 6th-chapter 3_equilibrium

36 mm

25 kg

60 mm90 mm

A B

P

C

Problem 3/95

75 mm

9 m 9 m

Problem 3/97

REVIEW PROBLEMS

3/95 The device shown in the figure is useful for liftingdrywall panels into position prior to fastening to thestud wall. Estimate the magnitude P of the force re-quired to lift the 25-kg panel. State any assumptions.

Ans. P 5 351 N

62 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_62 Tuesday Mar 13 2001 03:13 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/97 A 50-kg acrobat pedals her unicycle across the tautbut slightly elastic cable. If the deflection at the cen-ter of the 18-m span is 75 mm, determine the tensionin the cable. Neglect the effects of the weights of thecable and unicycle.

Ans. T 5 29.4 kN

3/96 The light bracket ABC is freely hinged at A and isconstrained by the fixed pin in the smooth slot at B.Calculate the magnitude R of the force supported bythe pin at A under the action of the 80-N z m appliedcouple.

45°

150 mm

A

B

C

200 mm

80 N·m

Problem 3/96

3/98 The uniform bar with end rollers weighs 60 lb and issupported by the horizontal and vertical surfaces andby the wire AC. Calculate the tension T in the wireand the reactions against the rollers at A and at B.

4′

A

B

C

1.5′

3′

Problem 3/98

Page 63: Estic merian 6th-chapter 3_equilibrium

3/99 A freeway sign measuring 12 ft by 6 ft is supportedby the single mast as shown. The sign, supportingframework, and mast together weigh 600 lb, withcenter of gravity 10 ft away from the vertical center-line of the mast. When the sign is subjected to thedirect blast of a 75 mi/hr wind, an average pressuredifference of 17.5 lb/ft2 is developed between thefront and back sides of the sign with the resultant ofthe wind-pressure forces acting at the center of thesign. Determine the magnitudes of the force and mo-ment reactions at the base of the mast. Such resultswould be instrumental in the design of the base.

Ans. R 5 1396 lb, M 5 25,600 lb-ft

Review Problems 63

p11 6191a_ch03 dm_63 Tuesday Mar 13 2001 03:13 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/100 Magnetic tape under a tension of 10 N at D passesaround the guide pulleys and through the erasinghead at C at constant speed. As a result of a smallamount of friction in the bearings of the pulleys, thetape at E is under a tension of 11 N. Determine thetension T in the supporting spring at B. The platelies in a horizontal plane and is mounted on a pre-cision needle bearing at A.

12′

14′

4′

6′

z

x

Problem 3/99

100 mm

A

B

CE

D

100mm

50mm

50mm

100 mm

All pulleyshave a

radius of25 mm

Problem 3/100

3/101 A vertical force P on the foot pedal of the bell crankis required to produce a tension T of 400 N in thevertical control rod. Determine the correspondingbearing reactions at A and B.

Ans. A 5 183.9 N up, B 5 424 N up

30°100mm

100mm

60 mm

120 mm

200 mm

T = 400 N

B

x

zy

A

P

Problem 3/101

Page 64: Estic merian 6th-chapter 3_equilibrium

3/102 Explain why the 50-kg uniform circular rod cannotbe in static equilibrium when in the indicatedposition.

64 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_64 Tuesday Mar 13 2001 03:13 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/104 The joints at O and A are vertical hinges which cansupport force in all three coordinate directions andmoment about the x- and z-axes. The mass of armOA is 2 kg, that of arm AB is 2.5 kg, and that of trayC is 4 kg. The mass center of each member is locatedat its geometric center. Determine the reaction atO for the configuration shown.

2 m

1.2 m

x

z

y

GC

B

A

1.2 m

1.2 m

0.8 m

0.8 m

0.8 m

0.8 m

Problem 3/102

3/103 The power unit of the post-hole digger supplies atorque of 4000 lb-in. to the auger. The arm B is freeto slide in the supporting sleeve C but is not free torotate about the horizontal axis of C. If the unit isfree to swivel about the vertical axis of the mountD, determine the force exerted against the rightrear wheel by the block A (or A9), which preventsthe unbraked truck from rolling. (Hint: View thesystem from above.)

Ans. A9 5 41.7 lb

30°8′

5′

30°

AB

C

D

AA′

Problem 3/103

0.6 m

0.8 m

45°

30°A

B

O

z

x

y

0.2 m0.2 m C

0.24 m

Problem 3/104

3/105 Each of the three uniform 1200-mm bars has a massof 20 kg. The bars are welded together into the con-figuration shown and suspended by three verticalwires. Bars AB and BC lie in the horizontal x-yplane, and the third bar lies in a plane parallel tothe x-z plane. Compute the tension in each wire.

Ans. TA 5 147.2 N, TB 5 245 N, TC 5 196.2 N

1200 m 600 m

xy

z

A

B

C600 m

1200 m30°

Problem 3/105

Page 65: Estic merian 6th-chapter 3_equilibrium

3/106 A large symmetrical drum for drying sand is oper-ated by the geared motor drive shown. If the massof the sand is 750 kg and an average gear-toothforce of 2.6 kN is supplied by the motor pinion A tothe drum gear normal to the contacting surfaces atB, calculate the average offset of the center ofxmass G of the sand from the vertical centerline. Ne-glect all friction in the supporting rollers.

Review Problems 65

p11 6191a_ch03 dm_65 Tuesday Mar 13 2001 03:13 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/108 Three identical steel balls, each of mass m, areplaced in the cylindrical ring which rests on a hor-izontal surface and whose height is slightly greaterthan the radius of the balls. The diameter of thering is such that the balls are virtually touching oneanother. A fourth identical ball is then placed on topof the three balls. Determine the force P exerted bythe ring on each of the three lower balls.

x_

O

600 mm

150 mm

BA

G

Detail of contactat B

20°

Problem 3/106

3/107 The 900-lb boom with center of gravity at G is heldin the position shown by a ball-and-socket joint atO and the two cables AB and AC. Determine the twocable tensions and the x-, y-, and z-components ofthe force reaction at O.

Ans. TAB 5 454 lb, TAC 5 554 lbOx 5 2489 lb, Oy 5 2582 lb, Oz 5 1445 lb

x

y

z

C

A

G

55°

40° O

O—

A– = 50′

O—

G– = 30′

O—

B– = O

—C– = 40′

B

Problem 3/107

Problem 3/108

3/109 The drum and shaft are welded together and havea mass of 50 kg with mass center at G. The shaft issubjected to a torque (couple) of 120 N z m, and thedrum is prevented from rotating by the cordwrapped securely around it and attached to pointC. Calculate the magnitudes of the forces supportedby bearings A and B.

Ans. A 5 610 N, B 5 656 N

200

120 N·m100

180

240

G

C

B

A

200200

140

150

Dimensions in millimeters

Problem 3/109

Page 66: Estic merian 6th-chapter 3_equilibrium

3/110 The L-shaped bar is supported by a ball-and-socketjoint at O [case (a)] and the two cables as shown.Explain why this configuration is improperly con-strained. (b) The ball-and-socket joint is now re-placed by the universal joint which can support, inaddition to three force reactions, a moment aboutthe y-axis but no moments about the x-and z-axes.Plot the two cable tensions, the magnitude of theforce reaction at O, and the moment reaction at Oas functions of the position x of the 100-lb cylinderover the range 0.5 # x # 4.5 ft. Explain any unusualcharacteristics of these plots. Neglect the weight ofthe bar throughout.

66 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_66 Tuesday Mar 13 2001 03:13 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

3/111 The device shown in section can support the load Lat various heights by resetting the pawl C in an-other tooth at the desired height on the fixed ver-tical column D. Determine the distance b at whichthe load should be positioned in order for the tworollers A and B to support equal forces. The weightof the device is negligible compared with L.

Ans. b 5 10.33 in.

z

xyx

O

O

C

D

A

BE

7′ 5′

1′

6′

2′

100 lb

4′

(a)

(b)

Problem 3/110

b

7″

20″

8″

3″

2″

Pawl C

D

B

A

L

C

Problem 3/111

Page 67: Estic merian 6th-chapter 3_equilibrium

*Computer-Oriented Problems

*3/112 The jib crane is designed for a maximum capacityof 10 kN, and its uniform I-beam has a mass of 200kg. (a) Plot the magnitude R of the force on the pinat A as a function of x through its operating rangeof x 5 0.2 m to x 5 3.8 m. On the same set of axes,plot the x- and y-components of the pin reaction atA. (b) Determine the minimum value of R and thecorresponding value of x. (c) For what value ofR should the pin at A be designed? (Use g 510 m/s2.)

Review Problems 67

p11 6191a_ch03 dm_67 Tuesday Mar 13 2001 03:13 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

*3/113 Determine and plot as a function of u the tensionT which must be produced by the winch in orderto steadily rotate the structural member about thefixed pivot at O. Use the range 0 # u # umax, whereumax is the value of u at which T goes to zero. Thestructural member has a mass of 35 kg per meterof its length.

Ans. T 52750 cos u 1 687 cos(u 1 607)

8 1F G F4 sin(u 1 607)12

cos(u 1 607) , u 5 79.17G max

30°

10 kN

3 m1 m

A

y

x

x

Problem 3/112

60°

A

B

O

2 m

2 m

4 m

θC

Problem 3/113

*3/114 The 50-kg cylinder is suspended from a clampingcollar at C which can be positioned at any horizon-tal position x between the fixed supports at A andB. The cable is 11 m in length. Determine and plotthe tensions in cable segments AC and BC as func-tions of x over the interval 0 # x # 10 m. What isthe maximum value of each tension and for whatvalue of x does it occur?

A B

C

10 m

50 kg

x

Problem 3/114

Page 68: Estic merian 6th-chapter 3_equilibrium

*3/115 Two traffic signals are attached to the 36-ft sup-port cable at equal intervals as shown. Determinethe equilibrium configuration angles a, b, and g,as well as the tension in each cable segment.

Ans. a 5 14.447, b 5 3.577, g 5 18.167

TAB 5 529 lb, TBC 5 513 lb, TCD 5 539 lb

68 Chapter 3 Equi l ibr ium

p11 6191a_ch03 dm_68 Tuesday Mar 13 2001 03:13 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

*3/117 The horizontal boom is supported by the cables ABand CD and by a ball-and-socket joint at O. Todetermine the influence on the reaction at O ofthe position of the vertical load L along the boom,we may neglect the weight of the boom. If R rep-resents the magnitude of the total force at O, de-termine by calculus the minimum ratio R/L andthe corresponding value of x. Then write a com-puter program for R/L and plot the results for0 , x , 6 m as a check on your calculations.

Ans. R/L 5 2!(47x /162 2 x/3 1 1(R/L)min 5 0.951 at x 5 0.574 m

A D

CB

35′

12 ′12 ′

100 lb

12 ′

200 lb

α γβ

Problem 3/115

*3/116 The two traffic signals of Prob. 3/115 are now re-positioned so that segment BC of the 36-ft supportcable is 10 ft in length and is horizontal. Specifythe necessary lengths AB and CD and the tensionsin all three cable segments.

A D

35′

10′C

200 lb

B

100 lb

Problem 3/116

z

O

AC

B

D

y

x

L

6 m

x

4 m

3 m

3 m

2 m

Problem 3/117

Page 69: Estic merian 6th-chapter 3_equilibrium

*3/118 The basic features of a small backhoe are shown inthe illustration. Member BE (complete with hy-draulic cylinder CD and bucket-control links DFand DE) weighs 500 lb with mass center at G1. Thebucket and its load of clay weigh 350 lb with masscenter at G2. To disclose the operational designcharacteristics of the backhoe, determine and plotthe force T in the hydraulic cylinder AB as a func-tion of the angular position u of member BE overthe range 0 # u # 907. For what value of u is theforce T equal to zero? Member OH is fixed for thisexercise; note that its controlling hydraulic cylin-der (hidden) extends from near point O to pin I.Similarly, the bucket-control hydraulic cylinderCD is held at a fixed length.

Review Problems 69

p11 6191a_ch03 dm_69 Tuesday Mar 13 2001 03:13 PM UG Job number: 6191aPublisher: Wiley Author: Meriam Title: Engineering Statics, 5/e tmm

*3/119 The mass center of the 1.5-kg link OC is located atG, and the spring of constant k 5 25 N/m is un-stretched when u 5 0. Plot the tension T requiredfor static equilibrium over the range 0 # u # 907

and state the values of T for u 5 457 and u 5 907.Ans. T 5 5.23 N at u 5 457

T 5 8.22 N at u 5 907

24″

34″

4″ 12″

18″

32″

12″

A

B

C

DF

E

G2

G1

H

I

O

θ

Problem 3/118

θ

A

B

C

OG = 160 mmOB = BC = 240 mm

D

G

O

T

k

Problem 3/119