error codes for toshiba 8070 6570 5570 4580

1. ADJUSTMENT1.1. Error CodesInstead of the set number, one of the following error codes is displayed with pressing the [CLEAR] key and the digital key 8 simultaneously when the CLEAR PAPER or CALL SERVICE symbol is flashing

Group Error Code Machine StatusPaper transport jam inside the copier (1)

E01 Leading edge of paper not reaching the fuser exit sensor

E02 Trailing edge of paper not passing the fuser exit sensor

E03 Paper remaining inside the copier at power ON

E09 Jam caused by an abnormal HDDE0A

Paper misfeeding E12 Bypass misfeedingE15 1st cassette misfeedingE16 2nd cassette misfeedingE17 3rd cassette misfeedingE19 LCF misfeedingE31E32E33

E34E35E36

Cover open jam E41 Front cover opwened during printingE47 Exit cover opened during printing

Transport jam (exit/reversing section and others )

E50E51E52E53E54E55E56E57E58E59E5AE5B

Transport jam (ADF) E71E72E73

Mac 2000 * TOSHIBA TEC 1-1 8070/6570/5570/4580 ADJUSTMENT

Group Error Code Machine StatusPaper jam at the finisher

EA1EA2EA3EA4EA5EA6EA8EA9EAAEABEACEADEAE

Paper transport jam inside the copier 2

EB3 Finisher ready time-out errorEB5 PSTPR-L standby time-out errorEB6 PSTPR-H standby time-out error

Paper feeding error(Refer to page 1-4)

C11 Duplexer side guide is abnormalC12 Duplexer stopper guide is abnormalC15 PFP upper tray is abnormalC16 PFP middle tray is abnormalC17 PFP lower tray is abnormalC18 LCF tray is abnormal

Scanner system related service call

C26 Peak detection errorC27 (Home switch does not turn OFF within a

fixed time ) Carriage initialization errorC28 (Home switch does not turn ON within a

fixed time ) Carriage initialization errorC29 Exposure lamp disconnection detected

Process system related service call 1

C36 Main charger wire cleaning operation abnormal

C37 Transfer belt operation abnormalProcess system related service call 2

CD1 Brush motor lock errorCD2 Auger motor lock error

Fuser related service call

C41 Thermistor abnormal or heater disconnection at power ON

C43 Thermistor abnormal during warming up or at standby after disconnection judgement

C44 Heater abnormal during warming up or at standby after disconnection judgement

C45 Upper heat rollor and thermistor abnormal

C46 Lower heat rollor thermistor abnormal at standby

8070/6570/5570/4580 ADJUSTMENT 1-2 Mac 2000 * TOSHIBA TEC

Group Error Code Machine StatusCommunication related service call

C56 Communication error between PFC and M-CPU

C57 Communication error between M-CPU and IPC

C58 Communication error between IPC and the finisher

C59 Communication error between M-CPU and L-CPU

System communication related service call

F07 Communication error between SYS and LGC boards

F11 Communication error between SYS and SLG boards

ADF related service call

C72 Error of aligning sensor adjustment C73 EEPROM initialization error C74 Error of exit sensor adjustmentC76 Transmission time-out errorC77 Transmission buffer fullC78 ADF power ON I/F errorC79 Reception time-out error C80 Error of timing sensor adjustment

Other service call C94 M-CPU is abnormalC99 PFC microcomputer is abnormal

Laser optical system related service call

CA1 Polygonal mirror motor is abnormalCA2 H-SYNC is abnormalCA3 Secondary scanning rough adjustment

errorCA4 Primary scanning counter load errorCA5 Laser power adjustment errorCA6 Laser PWM calibration errorCA9 Image data transmission error from SYS

board CAA Secondary scanning fine adjustment

error CAB Secondary scanning inter-page

compensation errorCAC Primary scanning dot adjustment errorCAD Primary scanning tap adjustment errorCAE Primary scanning tap amount

measurement errorCAF Primary scanning inter-page

compensation errorCDO Laser initializing time-out error

Finisher related service call

CB1CB2CB3CB4CB5


CB6CB7CB8CB9


Group Error Code Machine StatusFinisher related service call

CBACBBCBCCBDCBECBFCCOCC1CC2

Service call for others

F10 HDD formatting error


1.2.2 Output signal check (test mode 03)


error codes for toshiba 8070 6570 5570 4580

Documents