ergon catalogus

Ergonomic Series 2012No. 1 / 2012 GERmAn InnovATIon

Development Partner:German Sport University Cologne

P. 2 SaddlesP. 6 Contour PedalsP. 8 Pedal Cleat Adjustment SystemP. 9 Reportage Topeak Ergon Racing TeamP. 10 Racing Grips P. 12 Performance Comfort GripsP. 18 Technical GripsP. 19 Reportage Ergon Factory RiderP. 20 Gloves

2 WWW.ERGON-BIKE.COM

* Measured in the pre-upholstered state. ** Variance is possible.

100% Ergonomics. 100% Mountain Biking.

Designed from the ground up, Ergon’s ergonomically optimized Mountain Bike Saddle combines high performance and fit in a previously unobtainable way. A 3D saddle shell - innovative ‘hollows’ in the shell - allow for considerably more damping material in the seat bone areas, than any other saddle in this category.

1: Ultra-thin, flex optimized carbon or GFK saddle shell with isolated rear mounting rails for added flex. 2: Innovative, multi-layered cushioning with progressive damping. Tuned damping correlates with saddle width / use. 3: Nose mounted micro damper. 4: Saddle nose underside rubber cushion for shouldering the bike. 5: Chaff-reducing silicon coating on Pro and Carbon Pro models. 6: Optional standard rails, or Monolink® rail system (patent pending) allowing for maximum adjustment. All SM3 saddles are designed and engineered in Germany and manufactured by hand by Selle Italia in Italy.

1

2

3

5

6

4

Which is the correct saddle width?Scientific studies have concluded that in order for a saddle to be comfortable, it must match the individual sit bone width of the rider. This distance however changes depending on the angle at which the rider’s upper body is at. If the rider sits upright on the saddle, it is the rear parts of the sit bones which take their weight. As the rider leans more forward, then the point of the sit bone which makes contact rolls forwards. As the pelvis is also V formed towards the front, the contact area on the saddle needs to be large enough to provide comfort in different sitting positions. Ergon saddles are designed around the male pelvis form. For riders with a sit bone width of 10 - 13 cm we suggest size S, and for those with a sit bone distance of 12 - 15 cm we suggest L. There is some cross over, so we suggest test riding where possible.

Sit bone widthSaddle Size

10-13 cmS

12-15 cmL

Recommended Sizes**

Small10-13 cm

Large12-15 cm

3D Progressive Setup

Ultra-thin, flex optimized, carbon composite 3D saddle shell (Carbon Composite only on Pro / Carbon Pro models). Saddle shell is formed with 3D pockets under the sit bones allowing for extra padding. Y-Flex nose to seat design provides maximum freedom of movement when pedalling.

Highly elasticcomfort padding

Internal harderpadding

Saddle shell with3D pockets

State of the Art Saddle Development The Ergon Product Development Department utilized state of the art simulations, construction methods and analysis in the development of the SM3. For example when creating the Ultra-thin saddle shell, FEM analysis was fundamental in mapping the load and stress areas. The shape of the saddle from top to bottom was defined in the Ergon Ergonomics Laboratory using a multitude of pressure sensing equipment combined with real world experience on test rides. With this, many iterations lead to the final shape.

1. FEM analysis used in development process: Maximum deflection 6.19054mm*2. Saddle shell designed with homogenous flex throughout.

1 2

3WWW.ERGON-BIKE.COM

Super-light top of the range World Cup Team model. Flex Optimized Carbon Composite saddle shell. Super-light Carbon Fibre saddle rails. Friction minimizing silicon coating prevents chaffing. Soft, breathable, easy to clean, synthetic leather lorica micro-fibre cover. Alcantara® rear section. Available in sizes S and L for different sit-bone distances.

SizesWeightRailsCoverShellUsemSRP

• S (Small), L (Large)• ca. 184 g* (Large) / 179 g* (Small)• Carbon• Lorica® Micro Fibre, Alcantara® Rear Section• Carbon Fibre Ultra Thin Y-Flex Construction• Mountain Bike Racing, Cross Country, Marathon• $ 229.95

440 000 25 SM3-L Pro Carbon440 001 25 SM3-L Pro Carbon White440 002 25 SM3-L Pro Carbon Team Edition 440 000 20 SM3-S Pro Carbon440 001 20 SM3-S Pro Carbon White440 002 20 SM3-S Pro Carbon Team Edition

white Team Edition

New SM3 Pro Carbon

* Weights may vary owing to manufacturing tolerances.


Flex Optimized Carbon Composite saddle shell. Lightweight Tinox hollow rails. Friction minimizing silicon coating prevents chaffing. Soft, breathable, easy to clean, synthetic leather futura® micro-fibre cover. Diamantino rear section. Available in sizes S and L for differentsit-bone distances.


• S (Small), L (Large)• ca. 218 g* (Large) / 213 g* (Small)• TiNox• Futura® Mirco Fibre, Diamantino® Rear Section• Carbon Fibre Ultra Thin Y-Flex Construction• Mountain Bike Racing, Cross Country, Marathon• $ 159.95

440 000 15 SM3-L Pro440 001 15 SM3-L Pro White 440 000 10 SM3-S Pro440 001 10 SM3-S Pro White

Flex Optimized GFK saddle shell. Lightweight Tinox hollow rails. Soft, breathable, easy to clean, synthetic leather futura® micro-fibre cover. Available in sizes S and L for different sit-bone distances.


• S (Small), L (Large)• ca. 223 g* (Large) / 218 g* (Small)• TiNox• Futura® Micro Fibre• GF-Composite Ultra Thin Y-Flex Construction• Mountain Bike Racing, Cross Country, Marathon• $ 129.95

440 000 05 SM3-L440 000 00 SM3-S

white


New SM3 Pro

New SM3

5WWW.ERGON-BIKE.COM

Flex Optimized GFC saddle shell. Monolink® Carbon Composite Rail. Soft, breathable, easy to clean, synthetic leather futura® micro-fibre cover. Available in sizes S and L for different sit-bone distances.


• S (Small), L (Large)• ca. 190 g* (Large) / 185 g* (Small)• Carbon Composite Monolink®

• Futura® Micro Fibre• GF-Composite Ultra Thin Y-Flex Construction• Mountain Bike Racing, Cross Country, Marathon• $ 169.95

440 000 55 SM3-L Monolink®

440 000 50 SM3-S Monolink®

440 000 65 SM3-L Pro Carbon Monolink®

440 001 65 SM3-L Pro Carbon Monolink® White440 002 65 SM3-L Pro Carbon Monolink® Team Edition 440 000 60 SM3-S Pro Carbon Monolink®

440 001 60 SM3-S Pro Carbon Monolink® White440 002 60 SM3-S Pro Carbon Monolink® Team Edition


• S (Small), L (Large)• ca. 194 g* (Large) / 189 g* (Small)• Carbon Composite Monolink®

• Lorica® Micro Fibre, Alcantara® Rear Section• Carbon Fibre Ultra Thin Y-Flex Construction• Mountainbike, Cross Country, Marathon• $ 199.95

Super-light top of the range World Cup Team model. Flex Optimized Carbon Composite saddle shell. Monolink® carbon composite saddle rails for maximum adjustment. Friction minimizing silicon coating prevents chaffing. Soft, breathable, easy to clean, synthetic leather lorica® micro-fibre cover. Alcantara® rear section. Available in sizes S and L for different sit-bone distances.

white Team Edition

New SM3 Pro Carbon Monolink ®

New SM3 Monolink ®



Optimized power transfer, foot position,leg motion with normal shoes - PC2.

Dr. Kim TofauteSports Ergonomist

“From an ergonomic perspective pedals should not be overlooked for achieving optimized fit for bike and rider. Pedals are the point where muscle power is transferred to the bike, and therefore correct positioning of the foot and the leg is essential. Additionally incorrectly positioned feet and legs are the cause of knee complaints, so getting this right improves comfort as well as efficiency. The Ergon PC2 Contour Pedal uniquely addresses all of these factors with its contoured platform, inner-stop guide and narrow q-factor.”

Oversized integrated reflectors.Development partner: Busch & Müller, Germany

Superlight pedal body made from high performanceGF-Composite. Development Partner: Magura, Germany.

Ultra-Narrow axle constructions reduces Q-Factor, and is biomechanically more efficient.

Maintenance free polymer bearings with radial seals. Development partner: Igus®, Germany.

Inner-stop for intuitively correct foot positioning on the pedal.

Anatomically contoured platform, 6° angle for better joint allignment, varus (knee) angle correction. Optimizes the biomechanics of the leg (hip-knee-foot). Increases efficiency, minimizes knee complaints and hot spots / numbness in the feet.

3M-SafetyWalk™ creates a slip free platform and increases power transfer.

Dramatically increased contact area between shoe and pedal – increases power transfer and energy efficiency, reduces concentrated pressure points on the feet.

7WWW.ERGON-BIKE.COM

The PC2 redefined the market for touring / commuting / everyday pedals. The PC2 Evo takes this one step further. Using lightweight materials, such as a carbon composite pedal body, and hollow mat chromed axle, the weight has further reduced. Other high end details are the CNC machined aluminium axle cap, and white integrated reflectors* for increased visibility.

Shoe Size

materialUseBearingsmSRP

• Small (max. EU 42 / UK 7.5 / US 8.5) Large (min. EU 43 / UK 8 / US 9)• Carbon Composite• Touring, Commuting, General Riding• Maintenance free polymer bearing• $ 99.95

480 100 02 PC2-S Evo* (Pair)480 100 12 PC2-L Evo* (Pair)

* Please check local traffic regulations - may or may not be road legal.

Shoe Size

materialUseBearingsmSRP

• Small (max. EU 42 / UK 7.5 / US 8.5) Large (min. EU 43 / UK 8 / US 9)• Superlight GF-Composite• Touring, Commuting, General Riding• Maintenance free polymer bearing• $ 79.95

A more efficient pedal. Ergon introduces the first flat pedal (or Contour Pedal as we call it) to provide an ergonomic and positive connection between bike and user. The first pedal designed with biomechanics and correct foot position in mind. Advantages are increased power transfer, more control and fewer hot spots and knee complaints. The Ergon PC2 is the first non SPD-type pedal constructed with the ergonomic biomechanical demands of the user as a priority. 480 100 00 PC2-S (Pair)480 100 10 PC2-L (Pair)

PC2

20102011materialvision 2011

New PC2 Evo.


480 000 00 TP1 Shimano SPD® compatible480 000 10 TP1 crankbrothers® compatible480 000 01 TP1 Shimano SPD - SL® compatible480 000 05 TP1 LOOK KéO® compatible

Shoe SizematerialContentsmSRP

• One fits all• Tech. Polypropylene• TP1, Handbook, Reference stickers• $ 29.95

no loss in power.The first ever tool for simple yet precise Installation of cleats on cycling shoes.

The critical interface. The energy that goes into cycling is transferred via the pedal, shoe and cleat. Ergonomics in this area plays a massive role. Without an ergonomic setup power and performance will be lost. Comfort will be compromised. Injury could result. Correctly installed cleats are noticeable from the first ride. The Ergon TP1 allows the accurate adjustment of the three axis which are important when installing cleats. The fore/aft position, the stance (Q-Factor) and the foot angle. It is simple, fast and effective.

The tool is completed by a small handbook. This is a guide to basic ergonomics of the foot and leg, the biomechanic consequences and a simple step by step manual for using the TP1. For expert users information is provided about maximising performance. The tool is a favourite of Pro road and MTBers.

IF Eurobike Award Gold Winner 2008reddot Design Award Winner 2010

1. Fore / Aft adjustment 2. Adjusting the stance (Q-Factor) 3. Adjusting the cleat angle

The crankbrother‘s Eggbeater pedal system is a favorite of many, and therefore we jumped at the chance of designing a TP1 for the specific needs of these users. Accurate, simple and precise cleat (re)placement is now possible.

crankbrothers® compatible

2008

SPD®-SL users, one of the most popular road pedal systems, can now benefit from the accuracy and piece of mind offered by an Ergon TP1. The tools form allows all regularly sized road shoes to be set up correctly for more performance and long-term comfort on the bike.

Shimano SPD - SL® compatible

Look KeO® users, one of the most popular road pedal systems, can now benefit from the accuracy and piece of mind offered by an Ergon TP1. The tools form allows all regularly sized road shoes to be set up correctly for more performance and long-term comfort on the bike.

LOOK KéO® compatible

TP1 Pedal Cleat Tool Shimano SPD® compatible

LOOK KéO® compatible Irina Kalentievawww.irina-kalentieva.com

Alban Lakatawww.albanlakata.com

Ira is one of the strongest mountain bikers worldwide.A long list of championships, wins and medals underlines this. 2 World Championship Titles, an Olympic Medal and countless national titles. Silver in the World Championships in 2010 she has ridden for Team Topeak Ergon since 2006. She is a member of the family and provides valuable input for product development.

XC World Championship Silver 2010XC World Champion 2009 and 2007olympic XC Bronze 2008

Hard on himself, hard on the bike, hard on his competition - the Albanator. “He is like a dirtbike. When others are worn out and backing off, he knocks it down a gear and disappears into the distance,” the words of team Mechanic Lars Hartwich. It works for him. 2010 World Marathon Champion and a complete weight weenie - he pushes the product development hard too.

marathon World Champion 2010marathon World Championship Silver medal 2009European marathon Champion 2008

9WWW.TOPEAK-ERGON.COM

There aren’t many real Legends in the MTB scene, but Dave Wiens is one of the few. For over 20 years he has raced against, and quite often beaten the best in the World. A career that has seen him as the US National Champion twice, he has managed as well as raced for teams. His status was officially recognised in 2002 with his admission to the “Mountain Bike Hall of Fame”.

In 2009 the score was settled as Dave fought to win his seventh Leadville 100, against amongst others, Lance Armstrong (who he had beaten in 2008). Finishing second to Lance though is something only Alberto Contador can better! With Wiens’ experience his input to Ergon cannot be quantified.

Topeak-Ergon Racing Teamwww.topeak-ergon.com

Since 2005 Topeak-Ergon Racing Team has been one of the most successful Professional Mountain Bike Teams worldwide. World XC Champion, World Marathon Champion, European Marathon Champion, World 24h Championships Pairs Silver, German National Champion - a few of the successes the team has in the last five years.. Topeak-Ergon Racing Team is an essential part of the research and development into new products, flowing feedback directly into the core of product development.

Ergon’s support does not stop with Topeak-Ergon Racing Team. Through our international distributors Ergon can be seen being used by top-level athletes Worldwide. From Japan to the United Kingdom, Brazil to Italy. Many top riders demand they ride Ergon. We also support many local events, where the unsung heroes, the end users, get to experience Ergon.

Dave Wienswww.topeak-ergon.com

The marathon Grip.Developed as a specific marathon grip, the GS1 has become the racer‘s grip of choice. The grip‘s unique internal construction supports the hand using two internal supports individually tuned for perfect rebound and control. The lightweight leichtbau Direct Control rubber ensure ultimate feel and feedback. Available in two sizes. Sizes

WeightClampUsemSRP

• S (Small), L (Large)• ca. 155 g* (Large) / 146 g* (Small)• Aircraft Aluminum• Mountainbike, Marathon• $ 39.95

424 000 17 GS1-L424 600 17 GS1-L Team Edition424 600 19 GS1-L White

424 000 12 GS1-S424 600 12 GS1-S Team Edition424 600 14 GS1-S White

Racing


The brand new grip of the 2010 World marathon Champion Alban Lakata. Especially tuned for Endurance riding.

White

A new standard.

The GS grip series offers an optimized balance of comfort and performance required by top endurance athletes. A completely new grip from the ground up, it uses DirectControl Leichtbau rubber to keep the weight down, combined with a new, more cushioned form to protect the hands better on all day rides, 24 hour and marathon racing. The grip has 3 distinct areas, using different compounds and textures to provide grip and comfort as required. The GS2 Carbon adds a independently adjustable 3 finger bar end from 100% carbon (50 g each bar end).

424 000 57 GS2-L Carbon424 600 57 GS2-L Carbon Team Edition424 000 52 GS2-S Carbon424 600 52 GS2-S Carbon Team Edition

SizesWeightBarendUsemSRP

• S (Small), L (Large)• ca. 220 g* (Large) / 212 g* (Small)• 100% Carbon• Mountainbike, Marathon•$ 99.95

Team Edition

Team Edition

GS1

GS2 Carbon

Recommended for use with: HX Glove Series


Annodized, highly securelightweight aluminum clamp.

A new design from the ground up - designed for endurance riding.

Reduced wing for easier hand positioning.

DirectControl Leichtbau rubber for precise feedback and optimized damping.

* Weight per pair, without end plugs (where applicable).

White


• S (Small), L (Large)• ca. 231 g* (Large) / 222 g* (Small)• GF-Composite with rubber inserts• Mountainbike, Marathon•$ 59.95

Using the grip body as the GS2 Carbon, the GS2 adds an innovative GFC 3 finger bar end. Featuring non-slip rubber inserts, the bar end doubles as the clamp, allowing both the grip and the bar end to be independently adjusted.

424 000 37 GS2-L424 600 37 GS2-L Team Edition424 600 38 GS2-L White

424 000 32 GS2-S424 600 32 GS2-S Team Edition424 600 33 GS2-S White

11WWW.ERGON-BIKE.COM

Racing


• S (Small), L (Large)• ca. 289 g* (Large) / 280 g* (Small)• GF-Composite with rubber inserts• Mountainbike, Marathon•$ 69.95

The GS3 is the bigger brother of the GS2. Using the same grip body, thebenefits of Leichtbau DirectControl rubber and the new endurance design have beencombined with a full sized GF-Composite bar end. Featuring non-slip rubber inserts,the bar end doubles as the clamp for grip allowing both to be individually angled.

424 000 97 GS3-L424 000 92 GS3-S

Team Edition

GS2

GS3




Performance Comfort

Problem: Carpal tunnel syndrome

Solution: Ergon Grip

Problem: Ulna nerve irritation

Solution:Ergon Grip

Ergon GP and GS grips prevent numb fingers, painful hands and forearms – problems that many riders face. The cause of this is high pressure on the particularly sensitive areas of the palm and an incorrect hand position. Due to their anatomically optimal design, Ergon grips provide a contact surface of 100%. Regular grips only provide a contact surface of approximately 60%. With increased contact surface, pressure is especially reduced in the area of

the ulna nerve, thus decreasing the likelihood of numbness. Furthermore, the anatomic form of the Ergon Performance and Race Series grips corrects your hand position. An incorrect hand position and overloading of the median nerve (a leading cause of carpal tunnel syndrome) are impossible as long as the grip is mounted correctly.

The Size Difference.As hand size is different from person to person, Ergon manufactures theGP and GS ranges in two sizes - Small and Large. This difference is in the diameter of the grip. The reason for this is that a larger hand is better able to grip a larger grip with less stress and effort. This is the same in

reverse for small grip. A smaller hand needs a smaller grip to allow the hand to close around it. Of course, this is all also down to personal preference. More information is available online at:www.ergon-bike.com

Size L: 8.5 - 10.5

Small:92 mm Outside Grip Circumference

Large:102 mm Outside Grip Circumference

Size S: 6.5 - 8.5

Short and Sweet. New Product Names in 2012.All Ergon product names follow a schematic within which product group are clearly split, yet related products are quickly identified. The Performance Comfort Series, for historical reasons, was not always consistent. In order to improve on this, and clarify the product line, the names have been adjusted.

This will be in place from the start of 2012.

until 2011:

Grips:GP1GC2GR2GR3GC3

from 2012

GP1 GP2 GP3 GP4 GP5

Performance Comfort:


Performance Comfort

GP1 Ergon’s original and ground breaking GP1 continues to set standards. Offeringoptimal pressure distribution and available in two sizes, it features a forged aluminumclamp for fast and secure installation. Adjustment of the support platform is achievedby simply loosening the clamp bolt and positioning the grip to the desired Newtralposition.

variants SizesBarendUsemSRP

• Regular | Gripshift® | Rohloff®/Nexus®

• S (Small), L (Large)•Forged Aluminum• Mountainbike, Touring, Commuting• $ 29.95

424 000 15 GP1-L424 001 15 GP1-L Gripshift® compatible424 002 15 GP1-L Rohloff® / Nexus® compatible

424 000 10 GP1-S424 001 10 GP1-S Gripshift® compatible424 002 10 GP1-S Rohloff® / Nexus® compatible

The GP2 replaces the best selling GC2 grip. The new 2 finger GFC bar end delivers increased grip thanks to the rubberized anti-slip lower texture, and optimized ergonomics. Bar end and grip body can be infinitely independently adjusted dependent on preference.

2/2007

“Excellent”

2/2008

2004

variantsSizesBarendUsemSRP


• S (Small), L (Large)• GF-Composite with rubber inserts• Mountainbike, Touring, Commuting• $ 39.95

Recommended for use with: HC Glove Series




New GP2



• S (Small), L (Large)•GF-Composite with rubber inserts•Commuting, Touring• $ 49.95

GP3 (formerly known as the GR2)

Composite3 Finger Bar Endwith rubberized texture.

Smooth texture preventsthumb rub

Optimized pressuredistribution preventsnumbness and aching.

Plastic intnernal skeleton supports the wrist while soft rubber ensured sufficient damping.

Two densities ofhypo-allergenic rubberensure comfort, precisesteering and damping -keeping you in control.

Asymmetric form followsthe anatomic specificsof both the left and righthand.



The GP3 features a GF-Composite 3-finger bar end with anti-slip rubber inserts. Its sizeand shape are ideal for small to medium sized hands (Size S: 6.5 – 8.5) as well as formedium to larger sized hands (Size L: 8.5 – 10.5). The bar end and the grip platformcan be independently adjusted for the correct support angle and provides theperfect fit for your individual riding style.


Performance Comfort

New: Grip Compound - Made in GermanyErgon’s product development team doesn’t only focus on Ergonomics - material research is also a core theme. The demands and testing our products undergo meet those of the automotive industry, and far exceed the industry standard. Ergonomics, Product Design and Engineering - everything is done in-house in Germany. It is from this that successful projects have been born, such as our GreenLab initiative, which explores the use of sustainable materials. For 2011 we quietly introduced what is a major milestone in our development. All grips in the Performance Comfort Series were switched to a new rubber compound. As part of this process 39 rubber compounds were developed and tested. It was worth it, the new material - made in Germany - meets the highest standards, is longer lasting and worldwide is exclusive to Ergon for the bicycle industry.

• Developed and Manufactured in Germany• Extremely high UV resistance - corresponds to automotive standards• Contaminant Free - Only medically approved ‘white oil’ used in production• All raw materials meet the standards set for use in food production - EU (2002/72/EG)• All raw materials meet the purity standards of European Resolution AP(89)1• Free of PAK - no Phthalates used in production• SGS TÜV certification (raw material safety certification)• Highest quality standard within the bicycle industry




• S (Small), L (Large)•GF-Composite with rubber inserts•Commuting, Touring• $ 69.95

In some situations people simply need more hand positions. Employing the much proven ergonomic grip body of the GP1, the GP5 introduces a hollow formed glass fiber reinforced ergonomically shaped bar end. Featuring rubberized inserts for positive grip, like all of Ergon’s bar ends it can be independently positioned relative to the grip and acts as the clamp preventing accidental rotation. The grip itself is available in two sizes.

GP5 (formerly known as the GC3)

The GP4 offers the recognized class leading ergonomics of all Ergon Performance Comfort Series grips, combined with a full size, ergonomic, angle adjustable bar end. This doubles to clamp itself and the independently adjustable grip into position. The bar end features rubberized inserts for a firm slip free hold.


• Regular• S (Small), L (Large)• GF-Composite with rubber inserts• Mountainbike, Touring, Commuting• $ 59.95


Performance Comfort



424 000 95 GP4-L424 000 90 GP4-S

GP4 (formerly known as the GR3)

3/2009

7-8/2009

1/2010: “Very good”

2009




Performance ComfortThe GP1 BioKork provides ultimate ergonomics for the hand just as the rest of Ergon’s Performance Comfort series do, however the unique qualities of cork means that it is now antibacterial and hypoallergenic. Cork’s natural damping qualities also make it an ideal grip material, and its now density mean the resulting grip is a lot lighter. The GP1 BioKork uses 40% cork, sourced from sustainable forests in Portugal which is certified for its ecologically sound production. This ecological theme is continued throughout the rest of the grip. The inner core is plastic reinforced using natural fibre, which make up 40% of its mass. In place of mineral oil, the gel in the palm section of the grip is vegetable oil based. The clamp can also be 100% recycled. It is all a result of Ergon’s “GreenLab” initiative.

variantsSizesClampUsemSRP

• Regular | Gripshift® | Rohloff/Nexus®

• S (Small), L (Large)• 100% Recyclable Aluminum•Mountainbike, Touring, Commuting• $ 39.95

GP1 BioKork

Ergon’s GreenLab initiative is about combining the core principles ofergonomics and performance with ecologically aware practices.

Introduced in 2010, and for 2011, the GreenLab initiative has played animportant role in the Ergon Development Department and the resultsof that can be seen starting with the innovations in the last two years.Ergon’s extensive grip assortment is now presented with completelyreworked and re-invented packaging. This uses as little material aspossible to achieve our aims, and much of the material used is recycled.

The sustainability of the packaging was a key factor, and that thepackaging can be recycled after use, and uses as few components aspossible, a priority – minimising the environmental impact. The result ofthis new packaging quest is so innovative that it has already won thecoveted German DesignPlus packaging prize. Further examples are theGP1 BioKork, GP3 BioKork and the GP5 BioKork grips. Once again, it is Ergon setting the standards using the most innovative materials and technology to achieve our aims.

Grip SurfaceImproved feel thanks tocork’s natural properties

Grip Rubber Compound40% Cork from certifiedsustainable forest

Grip Core40% Biowert® grass fibre

Clamp100% recyclable aluminum

424 000 16 GP1-L BioKork424 001 16 GP1-L BioKork Gripshift® compatible424 002 16 GP1-L BioKork Rohloff® / Nexus® compatible

424 000 11 GP1-S BioKork424 001 11 GP1-S BioKork Gripshift® compatible424 002 11 GP1-S BioKork Rohloff® / Nexus® compatible

6/2010 “Very good” 4/2010 “Very good” 2010

Endcap40% Biowert® grass fibre


materialvision 2011

Packaging Material Innovation 09


Performance Comfort

The GP3 BioKork offers a different feel thanks to the use of natural cork, while offering all the ergonomic advantages of every Ergon Performance Comfort Series grip. The 3 finger angle adjustablebar end offers an additional hand position.


• Regular• S (Small), L (Large)•GF-Composite with rubber inserts•Touring, Commuting• $ 79.95


• Regular• S (Small), L (Large)•GF-Composite with rubber inserts•Mountainbike, Touring, Commuting• $ 59.95

The GP5 BioKork offers all the ergonomic advantages of everyErgon Performance Comfort Series grip – dissipating pressure andoptimizing the hand and wrist position, combined with the uniquefeel of natural cork. The angle adjustable multi-hand position bar endfeatures rubberized inserts for a firm slip free hold.

424 000 26 GP3-L BioKork424 000 21 GP3-S BioKork

424 000 76 GP5-L BioKork424 000 71 GP5-S BioKork

GP3 BioKork (formerly known as the GR2 BioKork)

GP5 BioKork (formerly known as the GC3 BioKork)



Gripshift®

•bothgripsareshortened

Rohloff®/nexus®

• right grip is shortened

Regular shifters•bothgripsarelong

Adapted grips for different shifters.

Perfomance Comfort Series•forregularshifters•forGripshift®

•forRohloff®/Nexus®

Racing Series•forregularshifters

Technical Series•forregularshifters


Technical

Blue

optimized Surface1: Minimal thumb rub2: Shaped mid zone3: Rougher texture for increased grip

optimized Core4: ‘Window’ in grip core for improved feel5: Tuned and non-uniform wall thickness for improved damping

1 2 3 4 5

The choice of Ergon Factory Riders. One form, 5 colours. Increased damping thanks to use of a new compound. Weight greatly reduced through use of a stable composite clamp. Details: Inner core - Ergon Green (not visible when fitted). Carbon bar compatible. All of this for just $ 24.95. Recommended for use with: HA and HE Glove Series

SizesWeightClampUsemSRP

• One Size• ca. 115 g*• FMC - Fiber Matrix Composite• All Mountain• $ 24.95

424 100 80 GA1 Evo424 100 81 GA1 Evo White424 100 82 GA1 Evo Green

424 100 84 GA1 Evo Red424 100 83 GA1 Evo Blue

1/2011: GA1 “Excellent”

(Test for previous model)

White RedBlack Green

* Weight per pair, without end plugs.

New GA1 Evo


Hans Rey Holger meyer Stefan Herrmann Karen Eller

Tibor Simai

“Performance and style are the be all and end all. The GA1 Evo ticks these boxes. Excellent grip and absolutely bombproof on the bars. Arm pump is a thing of the past, no matter how many runs I do.”

Richie Schley

“Ergon grips are simply better. The external clamp communicates the precise location of the end of the bars. The ergonomic shape and feel is superb. Try them, find out yourself.”

Photographer: Blake Jorgenson

Photographer: Markus Greber

Photographer: Viktor Strasse

Downhill, Freeride, 4-Cross, Dirt, Enduro. Ergon searches out some of the best riders in every discipline to assist with product development. Technical riding experts, downhillers, 4-cross riders and mountain bike legends. Their feedback is extremely important and flows into the products.

Timo Pritzel

“The more difficult the trick, the more important it is that the grips give you total feedback. They communicate the bike to you, and allow you to control it. Also, when you bottom out the suspension (which you will!) the ergonomic form of Ergon’s GA1 Evo dissipates the shocks efficiently. Add to that the colors, and why would you use anything else?”

Ergon Factory Rider “EFR”


Racing

The HX1 is specially cut and designed to be close-fitting andlightweight for cross-country and race applications. It matchesperfectly to the GS grip series. Thin padding for increasedtrail feedback and thin breathable back of hand material make fora comfortable yet unobtrusive glove. The silicon print is speciallydesigned to prevent the glove twisting in use.

SizesPalm materialUsemSRP

• XS - XXL• Micro-fibre Velour-leather• Mountainbike, Cross Country, Marathon• $ 44.95

The HX2, like the HX1 is specially cut and designed to be close-fittingand lightweight for cross-country and race applications matchingperfectly with the GS grip series. Thin padding for increasedtrail feedback and thin breathable back of hand materials make fora comfortable yet unobtrusive glove. The silicon print is speciallydesigned to prevent the glove twisting in use. Through the cleverplacement of seams in the fingers, they cannot be felt when wearingthe glove.

460 003 00 HX1 X-Small460 003 01 HX1 Small460 003 02 HX1 Medium460 003 03 HX1 Large460 003 04 HX1 X-Large460 003 05 HX1 XX-Large


• XS - XXL• Micro-fibre Velour-leather• Mountainbike, Cross Country, Marathon• $ 39.95

460 003 40 HX2 X-Small460 003 41 HX2 Small460 003 42 HX2 Medium460 003 43 HX2 Large460 003 44 HX2 X-Large460 003 45 HX2 XX-Large

HX2

HX1

Recommended for use with: GS Grip Series

Recommended for use with: GS Grip Series


Performance Comfort

The Ergon HC1 is a short fingered glove, especially designed foruse with the Performance Comfort series of grips. The glove featuresflexible yet robust mesh material for ventilation of the back of thehand. The thinly padded palm and fingers allows for increased feeland the benefits of Ergon grips not to be restricted. The ball of thehand has a slight increase in cushioning material for better pressurerelief of this sensitive area.

The long fingered glove, the Ergon HC2 is again especiallydesigned for use with the Performance Comfort series of grips. Theglove features the same flexible yet robust mesh material as the HC1for ventilation of the back of the hand. The thinly padded palm andfingers allows for increased feel and the benefits of Ergon grips not tobe restricted. The ball of the hand has a slight increase in cushioningmaterial for better pressure relief of this sensitive area. The fingersare slightly bent, even before the glove is put on, as on the bike thehand is usually closed. Through the clever placement of seams, theycannot be felt when wearing the glove.

460 002 40 HC2 X-Small460 002 41 HC2 Small460 002 42 HC2 Medium460 002 43 HC2 Large460 002 44 HC2 X-Large460 002 45 HC2 XX-Large


• XS - XXL• Micro-fibre Velour-leather• Touring, Leisure, Commuting• $ 35.95

460 002 00 HC1 X-Small460 002 01 HC1 Small460 002 02 HC1 Medium460 002 03 HC1 Large460 002 04 HC1 X-Large460 002 05 HC1 XX-Large


• XS - XXL• Micro-fibre Velour-leather• Touring, Leisure, Commuting• $ 39.95

HC1

HC2

Recommended for use with: GP Grip Series

Recommended for use with: GP Grip Series


Technical

The award winning best selling HE2 is optimized for All Mountain and Enduro use, and makes a perfect combination with Ergon’s Technical Series grips. Offering protection and freedom of movement, the elasticated wrist band stablizes the wrist, while a Kevlar insert protects the ball of the hand. Thin padding allows for maximum feedback. Now available in brown and blue.

460 005 40 HE2 Extra Small460 005 41 HE2 Small460 005 42 HE2 Medium460 005 43 HE2 Large460 005 44 HE2 Extra Large460 005 45 HE2 Extra Extra Large

SizesPalm materialUsagemSRP

• XS - XXL• Micro-fibre Velour-leather• Enduro, Downhill, Freeride• $ 39.95

460 005 50 HE2 Brown X-Small460 005 51 HE2 Brown Small460 005 52 HE2 Brown Medium460 005 53 HE2 Brown Large460 005 54 HE2 Brown X-Large460 005 55 HE2 Brown XX-Large

460 005 60 HE2 Blue X-Small460 005 61 HE2 Blue Small460 005 62 HE2 Blue Medium460 005 63 HE2 Blue Large460 005 64 HE2 Blue X-Large460 005 65 HE2 Blue XX-Large

Blue

Recommended for use with: GA Grip Series

BrownBlack

New HE2


HA2

The Ergon HA2 is an all-mountain glove matching the GA series of grips. The glove offers a combination of protection and flexibility. A high quality integrated closure makes for a crease and seam free cuff. A Kevlar insert offers additional protection for the ball of the hand, while carefully positioned padding ensures the required feedback is not lost.

460 004 40 HA2 X-Small460 004 41 HA2 Small460 004 42 HA2 Medium460 004 43 HA2 Large460 004 44 HA2 X-Large460 004 45 HA2 XX-Large


• XS - XXL• Micro-fibre Velour-leather• Enduro, Downhill, Freeride• $ 44.95

Recommended for use with: GA Grip Series

WWW.ERGON-BIKE.COM

* Product names re-alligned for 2012.

Ergon® is a worldwide trademark, Ergon® product and packaging designs are worldwide patent pending. GripShift® are registered trademarks of Sram® Inc, Shimano®, Nexus® are registered trademaks of Shimano® Inc, Rohloff® is a registered trademark of Rohloff AG, SPD® is a registrated trademark of Shimano® Inc., Kéo® is a registrated Trademark of LOOK® Cycle International, crankbrothers® is a registrated trademark of crankbrothers® Inc., Monolink® is a Trademark of Selle Italia®. Druckfehler, Irrtümer und Änderungen vorbehalten

2011: SM3 Pro Carbon

Monolink®

2010: PC2

2008: TP1

2006: GX1 / GX2

2005: GP3*

2011: PC2

2010: GP1 Biokork

2009: GP5*

2005: GP3*

2004: GP1

2010: GP5* 2010: GP1 Biokork

7/2011: BC2 „Very good“

1/2011: GX1 - Test Winner

“Excellent”

1/2011: GA1 “Excellent”

7/2010: BC3 “Very good”

2/2007: GP1 - Best Buy

“Excellent”

5/2010: BC2 “Very good”

3/2009: GP5*

2/2008: GP1

2/2008: GP2*

Design-Awards

Tests

7/2011: BX2 “Very good”

(Test for previous model)

Ergon Racing Teams

8/2011: BC3 “Good”

Ergon International: RTI Sports GmbHUniversitaetsstr. 2, 56070 Koblenz/GermanyT +49 (0) 261 899998-28, F +49 (0) 261 899998-19www.ergon-bike.comwww.rtisports.de

Ergon USA, Inc. 8285 Sunset Blvd. Suite #12West Hollywood, CA. 90046T 323-656-2788, T 877-573-7466 (Toll Free)F 323-848-9097www.ergon-bike.com

2006-2010: GP1 12/2010: GP1 BioKork

materialvision 2011

2011: PC2

ergon catalogus

Documents

gfk saddle shell

art saddle development

correct saddle width

saddle width use

optimized mountain bike

sit bone distance

individual sit bone

sit bones