erection of hipped end - minera roof trusses · 2019-11-28 · loose timber inﬁll 2. hip board to...

Minera Roof Trusses Limited Five Crosses Industrial Estate, Minera, Wrexham LL11 3RD Email: [email protected] • Telephone: (01978) 758869 www.minera-rooftrusses.com Erection of a Hipped End with Structural Timber Drawing Number: MRT-SD-58 Designer: BS5268 Last Revised: July 2016 Connect with us: Company Registration Number: 1325682 SECTION PLAN Jack rafters birdsmouthed over wallplate (where applicable) Hipboard Wallplate Standard Roof Truss Multiple Truss (Fully nailed together to act as one unit) NOTES: 1. Multiple truss at top of hip to support loose timber inﬁll 2. Hip board to be birdsmouthed over wallplate. 3. Jack rafters to be birdsmouthed over wallplate to match trussed rafter roof and to be cut into hip board. 4. Ceiling joists to be supported on wallplate and in joist hangers on multiple truss. 5. The ends of any treated timber that is cut need to be treated with cut end preservative - Minera can supply this. Detail to be read in conjunction with Minera issued roof truss layout. 1. Note! This is only a typical detail as a guide on how to construct the hip end that you have on site. 2. These marks next to the trusses do not correspond with the truss marks of your roof layout. These marks are only to guide you. Always refer to your truss layout. Wallplate Ceiling Joist Rafters Joist Hanger Standard Roof Trusses Wallplate Ceiling Joists (Note 4) Multiple Truss forming Girder (Note 1) Hipboard (Note 2) Jack Rafter (Note 3) Birdsmouth Hip board birdsmouthed over wallplate (where applicable)

Upload: others

Post on 22-Apr-2020

4 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Page 1: erection of hipped end - Minera Roof Trusses · 2019-11-28 · loose timber inﬁll 2. Hip board to be birdsmouthed over wallplate. 3. Jack rafters to be birdsmouthed over wallplate

Minera Roof Trusses LimitedFive Crosses Industrial Estate, Minera, Wrexham LL11 3RD

Email: [email protected] • Telephone: (01978) 758869

www.minera-rooftrusses.com

Erection of a Hipped End with Structural Timber

Drawing Number: MRT-SD-58Designer: BS5268Last Revised: July 2016

Connect with us:

Company Registration Number: 1325682

SECTION

PLAN

Jack rafters birdsmouthedover wallplate(where applicable)

Hipboard

Wallplate

Standard Roof Truss

Multiple Truss (Fully nailed together to act as one unit)

NOTES:1. Multiple truss at top of hip to support loose timber infill

2. Hip board to be birdsmouthed over wallplate.

3. Jack rafters to be birdsmouthed over wallplate to match trussed rafter roof and to be cut into hip board.

4. Ceiling joists to be supported on wallplate and in joist hangers on multiple truss.

5. The ends of any treated timber that is cut need to be treated with cut end preservative - Minera can supply this.

Detail to be read in conjunction with Minera issued roof truss layout. 1. Note! This is only a typical detail as a guide on how to construct the hip end that you have on site.

2. These marks next to the trusses do not correspond with the truss marks of your roof layout. These marks are only to guide you. Always refer to your truss layout.

Wallplate

Ceiling Joist

Rafters

Joist Hanger

Standard Roof Trusses

Wallplate

CeilingJoists(Note 4)

Multiple Truss forming Girder (Note 1)

Hipboard (Note 2)

Jack Rafter (Note 3)

Birdsmouth

Hip board birdsmouthedover wallplate(where applicable)