Installation Guide

Guide dinstallation

2Safety Instructions

For your safety, read all the instructions in this guide before using the setting plate. Incorrect handling that ignores instructions in this guide could damage the setting plate or could result in personal injury or property damage. Keep this installation guide at hand for future reference.

Read the safety instructions in the User's Guide for your projector and follow the instructions in this document.

Explanation of SymbolsThe warning marks shown below are used throughout this installation guide to prevent personal injury or property damage. Make sure you understand these warnings when reading this installation guide.

Safety Precautions for Installation

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

Symbol indicating an action that must not be done

Symbol indicating an action that should be done

The setting plate is designed specifically for mounting a projector to a wall. If anything other than a projector is mounted, the weight may result in damage.If the setting plate falls, it could cause personal injury or property damage.

The installation work (wall mounting) should be performed by specialists who have technical knowledge and ability. Incomplete or incorrect installation could cause the setting plate to fall and cause personal injury or property damage. Contact the customer support office listed in Where to Get Help in the User's Guide for your projector when installing the setting plate.

Follow the instructions in this guide when installing the setting plate.If the instructions are not followed, the setting plate may fall, resulting in personal injury or property damage.

Handle the power cable carefully.Incorrect handling may cause fire or electric shock. Observe the following precautions when handling: Do not handle the power plug with wet hands. Do not use a power cable that is damaged or modified. Do not pull the power cable with too much force when routing the cable through the setting plate.

When you mount the projector on the wall with the setting plate, the wall requires enough strength to hold the projector and the setting plate. Confirm the weight of the projector and the setting plate before installation, and maintain the strength of the wall. If the wall is not strong enough, reinforce the wall before installation.

Do not install the setting plate in a place where it might be subjected to vibration or shock.Vibration or shock could cause damage to the projector or mounting surface. It could also cause the setting plate or projector to fall and cause personal injury or property damage.

Install the setting plate so that it can sufficiently support the weight of the projector and setting plate, and resist any horizontal vibration. Use M8 nuts and bolts.Nuts and bolts smaller than M8 could cause the setting plate to fall. Epson takes no responsibility for any damage or injury caused by incorrect installation.

Warning

Caution

Warning

3Engl

ish

Location

Before installing the projector, verify the power supply wiring for the installation location. Install the projector away from other electric devices such as fluorescent lights or air conditioners. Some

kinds of fluorescent lights could interfere with the remote control of the projector.

It is recommended to keep connection cable length less than 65 ft (20 meters) to reduce external noise. Install the setting plate in a place free from excessive dust and humidity to prevent the lens or optical

components from becoming dirty.

About This Installation Guide

This guide describes how to mount the BrightLink 450 Wi, PowerLite 460, and PowerLite 450W projectors to a wall using the exclusive setting plate.

The installation work should be performed by at least two qualified service personnel. If you need to loosen any screws during installation, be careful not to drop the setting plate.If the setting plate or projector falls, it could cause personal injury or property damage.

Inspect the setting plate on a regular basis to ensure there are no broken parts or loose screws.If there are any broken parts, stop using the setting plate immediately. If the setting plate or projector falls, it could cause personal injury or property damage.

Never modify the setting plate.

Do not hang on the setting plate or hang a heavy object on the setting plate.If the projector or setting plate falls, it could cause personal injury or property damage.

If you use adhesives to prevent the screws from loosening or things such as lubricants or oils on the slide plate fixing part of the projector, the case may crack and cause the projector to fall, resulting in personal injury or property damage. Do not use adhesives, lubricants, or oils to install or adjust the setting plate.

Tighten all screws firmly after adjustment.If the screws are not tightened firmly, the projector or setting plate may fall and cause personal injury or property damage.

Never loosen the bolts and nuts after installation.Confirm that the screws have not become loose on a regular basis. If you find any loose screws, tighten them firmly. If the screws are not tightened firmly, the projector or setting plate may fall and cause personal injury or property damage.

Do not install the setting plate in a location where the operating temperature for your projector model may be exceeded.Such an environment may damage the projector.

Install the setting plate in a place free from excessive dust and humidity to prevent the lens or optical components from becoming dirty.

Do not use excessive force when adjusting the setting plate.The setting plate may break, resulting in personal injury.

Warning

Caution

41 Package Contents s Page 5

2 Specifications s Page 7

3 Connecting Devices s Page 8

4 Positioning the Projector s Page 9(1) Installation worksheet for projecting on a pre-installed wall-

mounted board(2) Installation worksheet for projecting on a plain wall(3) Installation measurements in inches(4) Installation measurements in millimeters

5 Installing the Projector s Page 18(1) Install the wall plate on the wall(2) Determine the projection distance and pull out the slider(3) Attach the setting plate to the wall plate(4) Secure the projector to the setting plate(5) Connect the power cable and other cables to the projector

6 Adjusting the Image s Page 22(1) Turn on the projector(2) Display the test pattern(3) Change the aspect ratio if necessary(4) Adjust the focus(5) Use the left adjustment dial to adjust the horizontal roll(6) Use the right adjustment dial to adjust the horizontal rotation(7) Use the top adjustment dial to adjust the vertical tilt(8) Adjust the vertical position(9) Adjust the forward/backward slide

(10) Turn off the display of the test pattern or computer image

7 Attaching the Covers s Page 27(1) Attach the wall plate cover and end cap(2) Attach the cable cover to the projector

5Engl

ish

1. Package Contents

Mounting hardware

Use the bolts supplied with the setting plate to install it, as directed in this guide. Do not substitute these bolts with any other types.

Use commercially available M8 x 50 mm anchors (at least 3) or 8 x 80 mm lag bolts (at least 3) to attach the wall plate to the wall.

Gather the tools and parts you need before you begin installation.

Shape Name Quantity Application

M8 x 15 mm hexagon socket head cap bolt with washer

2 For installing setting plate

M5 x 12 mm hexagon socket head cap bolt with washer

2 For securing projector

M4 x 12 mm hexagon socket head cap bolt without washer

2 For installing wall plate cover

Hexagon wrenches (for M4, M5, and M8)

Wall plate cover

Setting plate (wall mount)

Template sheet(for installing the wall plate)

End cap

Wall plate

6Projector box

Interactive pens and AAA batteries*

Power cord

Projector

Epson Projector Software for Easy Interactive Function CD*

VGA computer cable

Remote control and AA batteries

USB cable*

Epson Projector Software for Meeting and Monitoring CD

Security stickerProjector CD

*Items included for the BrightLink 450Wi only. Extra pen and battery set are included in the U.S. and Canada only.

7Engl

ish

2. Specifications

Wall plate

Setting plate adjustment range

Item Specification Remark Reference Page

Setting plate weight Approx. 13.89 lb (6.3 kg)

Wall plate 4.85 lb (2.2 kg)Covers and cap 1.04 lb (0.47 kg)

Forward/backward slide adjustment range

0 to 11.81 in. (300 mm)

Refer to the figure below

Vertical slide adjustment range 4 Minimum: 1.10 in. (28 mm)Maximum: 1.67 in. (42.5 mm)

s 26

Vertical tilt adjustment range 5 Fine adjustments possible with adjustment dial s 25

Horizontal rotation adjustment range

5 Fine adjustments possible with adjustment dial s 25

Horizontal roll adjustment range 3 Fine adjustments possible with adjustment dial s 24

Horizontal slide adjustment range 1.77 in. (45 mm)

Refer to the figure below

[Unit: in. (mm)]9.87 (250)

17.97 (456)

9.05 (230)

8.74 (222)

6.3 (160)

9.71 (247)

0.59 (15)4.4 (112)

8 (203.2)

3.0(76)

1.8 (46)

4.75(121)

1.81 (46)

Forward/backward slide adjustment range:0 to 11.81 in. (300 mm)

Horizontal slide adjustment range: 1.77 in. (45 mm)

83. Connecting Devices

Make sure you have the power cable, computer cable, USB cable, and other parts at the location where the setting plate is to be installed.

Make sure you have all necessary cables for any devices, such as a document camera or microphone, that you will connect to the projector.

External speakers LAN device

Microphone

USB cable(for Easy Interactive Function)Document camera

Computer

Computer cable(for computer video output)

Connection Example

Dedicated USB cable(supplied with document camera)

Audio cable(commercially available product)

LAN cable

Power cord

9Engl

ish

4. Positioning the Projector

The BrightLink 450Wi and PowerLite 450W can project up to 96 inches diagonally for a WXGA image or 85 inches diagonally for an XGA image. The PowerLite 460 can project up to 102 inches diagonally for an XGA image. You can project onto a pre-installed whiteboard or directly onto a plain wall. The height of the included wall mount determines the maximum image size and how high the image appears on the wall or whiteboard. The distance of the projector from the wall (once it is mounted on the adjustable arm of the setting plate) also affects image size and position.

If you are planning to project on a whiteboard, the image may not fill the entire board, depending on the aspect ratio. If you match the image height to the boards height, gaps may appear on the sides of the board.

Use the following worksheets to determine the proper location of the wall plate on the wall. If you are projecting onto a pre-installed whiteboard, use the worksheet below. If you are projecting on a plain wall, use the worksheet on page 10.

Installation worksheet for projecting on a pre-installed wall-mounted board

(1) Measure the ceiling height (distance from the floor to the ceiling).

(2) Measure the height of the boards image area (h).

(3) Measure the width of the boards image area (w).

(4) Measure the distance from the floor to the bottom of the boards image area (f ).

(5) Measure the distance from the ceiling to the top of the boards image area (c).

(6) Measure the thickness of the board (x).

_____

_____ (h)

_____ (w)

_____ (f )

_____ (c)

_____ (x)

10 in. (254 mm)height of wall plate plus cover

Required distance from top of image area to wall plate (b)

Diagonal size of image area (S)

Height of image area (h)

Distance from ceiling to top of image area (c)

Width of image area (w)

Distance from floor to bottom of image area (f)

10

(7) Determine the aspect ratio of the board or of the images that will be projected. For new computers or laptops, this will most likely be WXGA (16:10). For older equipment, this will most likely be XGA (4:3). You may need to consult your IT director for this information.

4:3 XGA 16:10 WXGA 16:9 Widescreen

(8) Using the tables on pages 12 to 16 for your aspect ratio and desired image height (h), find the required distance between the top of the image area and the wall plate (b).

(9) Determine the position for your projector installation by adding the values for (f ), (h), and (b), plus an additional 10 inches for the height of the wall plate plus the cover.

If the ceiling height of your room (as noted in step 1) does not meet the minimum ceiling height required for your board, you may need to select a smaller image size or move the board to a lower position on the wall.

(10)After confirming your image size, use tape or a pencil to mark the distance (b) from the top of the image area on the board to the bottom of the wall plate.

(11)Align the line (horizontal) on the template sheet with the (b) mark, then align the center line on the template sheet with the center of the image area. Follow the instructions on page 18 to install the projector.

Installation worksheet for projecting on a plain wall(1) Measure the ceiling height (distance from the floor to the ceiling).

(2) Determine the desired aspect ratio of the image. For new computers or laptops, this will most likely be WXGA (16:10). For older equipment, this will most likely be XGA (4:3). You may need to consult your IT director for this information.

4:3 XGA 16:10 WXGA 16:9 Widescreen

(3) Using the tables on pages 12 to 16 for your aspect ratio, select the largest image size available for your ceiling height.

Image height (h)Image width (w)

(4) Determine the desired distance from the floor to the bottom of the image area (f ).

The recommended minimum distance is 30 inches. Images appearing less than 28 inches from the floor may be obstructed for some viewers.

(5) Find the top of the projected image area by adding distances (f ) and (h).

(6) Use the tables on pages 12 to 16 to determine the required distance from the top of the image area to the bottom of the wall plate (b).

(7) Add: Required distance from top of image area to wall plate (b)Height of image area (h)Distance from floor to bottom of image area (f )Height of wall plate plus cover

If the total exceeds the ceiling height, you will need to reduce the image size or reduce the distance from the floor to the bottom of the image area.

_____ (b)

_____ (f )

_____ (h)

_____ (b)

+10 inches

_____ total

_____

_____ (h)

_____ (w)

_____ (f )

_____

_____ (b)

_____ (b)_____ (h)_____ (f )+10 inches

_____ total

11

Engl

ish

(8) After confirming your image size, use tape or a pencil to mark the distance (b) from the top of the image area on the board to the bottom of the wall plate.

(9) Align the line (horizontal) on the template sheet with the (b) mark, then align the center line on the template sheet with the center of the image area. Follow the instructions on page 18 to install the projector.

The tables on the following pages provide installation information for all supported image sizes. The minimum ceiling height is based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

Use the worksheets, the illustration below, and the information in the tables on the following pages to determine the projection distance and placement of the wall plate. The recommended range for projection distance (a) is 2.76 to 14.57 inches (7 to 37 cm).

10 in. (254 mm) height of wall plate plus cover

Required distance from top of image area to wall plate (b)

Diagonal image size (S)

Ceiling height

Distance from ceiling to top of image area (c)

Width of image area (w)

Distance from floor to bottom of image area (f)

Height of image area (h)

Wall plate

Projection surface

Offset value for the position of the center of the screen and the center of the wall plate

Distance from wall of projection surface or whiteboard

2.55 in. (65 mm)

10 in. (254 mm)

Line on template

12

Inst

alla

tion

mea

sure

men

ts in

inch

esD

iago

nal

imag

e si

ze

(S)

16:1

0 W

XGA

for B

righ

tLin

k 45

0Wi,

Pow

erLi

te 4

50W

, and

Pow

erLi

te 4

60

4:3

XGA

for B

righ

tLin

k 45

0Wi a

nd

Pow

erLi

te 4

50W

16:9

Wid

escr

een

for B

righ

tLin

k 45

0Wi,

Pow

erLi

te 4

50W

, and

Pow

erLi

te 4

60

Min

. ce

iling

he

ight

*

Imag

e w

idth

(w

)

Imag

e he

ight

(h

)

Min

. pr

ojec

tion

di

stan

ce

(a)

Dis

tanc

e fr

om to

p of

imag

e to

wal

l pl

ate

(b)

Min

. ce

iling

he

ight

*

Imag

e w

idth

(w

)

Imag

e he

ight

(h

)

Min

. pr

ojec

tion

di

stan

ce

(a)

Dis

tanc

e fr

om t

op

of im

age

to w

all

plat

e (b

)

Min

. ce

iling

he

ight

*

Imag

e w

idth

(w

)

Imag

e he

ight

(h

)

Min

. Pr

ojec

tion

di

stan

ce

(a)

Dis

tanc

e fr

om to

p of

imag

e to

wal

l pl

ate

(b)

55

83

.844

.033

.03.

710

.8

56

84

.644

.833

.64.

111

.0

57

85

.445

.634

.24.

411

.2

58

86

.246

.434

.84.

811

.4

59

81.6

50.0

31.3

2.7

10.3

86.9

47.2

35.4

5.2

11.5

60

82.3

50.9

31.8

3.0

10.5

87.7

48.0

36.0

5.5

11.7

81.8

52.3

29.4

3.5

12.4

61

83.0

51.7

32.3

3.3

10.6

88.5

48.8

36.6

5.9

11.9

82.5

53.2

29.9

3.9

12.6

62

83.7

52.6

32.9

3.6

10.8

89.3

49.6

37.2

6.2

12.1

83.1

54.0

30.4

4.2

12.8

63

84.3

53.4

33.4

4.0

11.0

90.0

50.4

37.8

6.6

12.2

83.8

54.9

30.9

4.5

12.9

64

85.0

54.3

33.9

4.4

11.1

90.8

51.2

38.4

7.0

12.4

84.5

55.8

31.4

4.8

13.1

65

85.7

55.1

34.4

4.6

11.3

91.6

52.0

39.0

7.3

12.6

85.2

56.7

31.9

5.2

13.3

66

86.4

56.0

35.0

4.9

11.4

92.4

52.8

39.6

7.7

12.8

85.9

57.5

32.4

5.5

13.5

67

87.1

56.8

35.5

5.2

11.6

93.1

53.6

40.2

8.0

12.9

86.5

58.4

32.8

5.8

13.7

68

87.8

57.7

36.0

5.5

11.7

93.9

54.4

40.8

8.4

13.1

87.2

59.3

33.3

6.2

13.9

69

88.4

58.5

36.6

5.9

11.9

94.7

55.2

41.4

8.8

13.3

87.9

60.1

33.8

6.5

14.1

70

89.1

59.4

37.1

6.2

12.0

95.5

56.0

42.0

9.1

13.5

88.6

61.0

34.3

6.8

14.2

71

89.8

60.2

37.6

6.5

12.2

96.2

56.8

42.6

9.5

13.6

89.2

61.9

34.8

7.2

14.4

72

90.5

61.1

38.2

6.8

12.3

97.0

57.6

43.2

9.8

13.8

89.9

62.8

35.3

7.5

14.6

73

91.2

61.9

38.7

7.1

12.5

97.8

58.4

43.8

10.2

14.0

90.6

63.6

35.8

7.8

14.8

74

91.9

62.8

39.2

7.5

12.7

98.6

59.2

44.4

10.6

14.2

91.3

64.5

36.3

8.1

15.0

75

92.6

63.6

39.7

7.8

12.8

99.3

60.0

45.0

10.9

14.3

91.9

65.4

36.8

8.4

15.2

13

Engl

ish

* Ba

sed

on a

n im

age

30 in

ches

from

the

floor

; if t

he im

age

is lo

wer

, the

min

imum

cei

ling

heig

ht is

redu

ced

by th

e co

rres

pond

ing

mea

sure

men

t.

76

93.2

64.4

40.3

8.1

13.0

100.

160

.845

.611

.314

.592

.666

.237

.38.

815

.4

77

93.9

65.3

40.8

8.4

13.1

100.

961

.646

.211

.714

.793

.367

.137

.89.

115

.5

78

94.6

66.1

41.3

8.7

13.3

101.

762

.446

.812

.014

.994

.068

.038

.29.

415

.7

79

95.3

67.0

41.9

9.0

13.4

102.

463

.247

.412

.415

.094

.668

.938

.79.

715

.9

80

96.0

67.8

42.4

9.4

13.6

103.

264

.048

.012

.715

.295

.369

.739

.210

.116

.1

81

96.7

68.7

42.9

9.7

13.7

104.

064

.848

.613

.115

.496

.070

.639

.710

.416

.3

82

97.3

69.5

43.5

10.0

13.9

104.

865

.649

.213

.515

.696

.771

.540

.210

.716

.5

83

98.0

70.4

44.0

10.3

14.0

105.

566

.449

.813

.815

.797

.472

.340

.711

.116

.7

84

98.7

71.2

44.5

10.6

14.2

106.

367

.250

.414

.215

.998

.073

.241

.211

.416

.9

85

99.4

72.1

45.0

11.0

14.4

107.

168

.051

.014

.516

.198

.774

.141

.711

.717

.0

86

100.

172

.945

.611

.314

.5

99.4

75.0

42.2

12.0

17.2

87

100.

873

.846

.111

.614

.7

100.

175

.842

.712

.417

.4

88

101.

574

.646

.611

.914

.8

100.

776

.743

.112

.717

.6

89

102.

175

.547

.212

.214

.9

101.

477

.643

.613

.017

.9

90

102.

876

.347

.712

.615

.1

102.

178

.444

.113

.318

.0

91

103.

577

.248

.212

.915

.3

102.

879

.344

.613

.718

.2

92

104.

278

.048

.813

.215

.4

103.

480

.245

.114

.018

.3

93

104.

978

.949

.313

.515

.6

104.

181

.145

.614

.318

.5

94

105.

679

.749

.813

.815

.8

95

106.

380

.650

.314

.215

.9

96

106.

981

.450

.914

.516

.1

Dia

gona

l im

age

size

(S

)

16:1

0 W

XGA

for B

righ

tLin

k 45

0Wi,

Pow

erLi

te 4

50W

, and

Pow

erLi

te 4

60

4:3

XGA

for B

righ

tLin

k 45

0Wi a

nd

Pow

erLi

te 4

50W

16:9

Wid

escr

een

for B

righ

tLin

k 45

0Wi,

Pow

erLi

te 4

50W

, and

Pow

erLi

te 4

60

Min

. ce

iling

he

ight

*

Imag

e w

idth

(w

)

Imag

e he

ight

(h

)

Min

. pr

ojec

tion

di

stan

ce

(a)

Dis

tanc

e fr

om to

p of

imag

e to

wal

l pl

ate

(b)

Min

. ce

iling

he

ight

*

Imag

e w

idth

(w

)

Imag

e he

ight

(h

)

Min

. pr

ojec

tion

di

stan

ce

(a)

Dis

tanc

e fr

om t

op

of im

age

to w

all

plat

e (b

)

Min

. ce

iling

he

ight

*

Imag

e w

idth

(w

)

Imag

e he

ight

(h

)

Min

. Pr

ojec

tion

di

stan

ce

(a)

Dis

tanc

e fr

om to

p of

imag

e to

wal

l pl

ate

(b)

14

Inst

alla

tion

mea

sure

men

ts in

mill

imet

ers

Dia

gona

l im

age

size

(S

)

16:1

0 W

XGA

for B

righ

tLin

k 45

0Wi,

Pow

erLi

te 4

50W

, and

Pow

erLi

te 4

60

4:3

XGA

for B

righ

tLin

k 45

0Wi a

nd

Pow

erLi

te 4

50W

16:9

Wid

escr

een

for B

righ

tLin

k 45

0Wi,

Pow

erLi

te 4

50W

, and

Pow

erLi

te 4

60

Min

. ce

iling

he

ight

*

Imag

e w

idth

(w

)

Imag

e he

ight

(h

)

Min

. pr

ojec

tion

di

stan

ce

(a)

Dis

tanc

e fr

om to

p of

imag

e to

wal

l pl

ate

(b)

Min

. ce

iling

he

ight

*

Imag

e w

idth

(w

)

Imag

e he

ight

(h

)

Min

. pr

ojec

tion

di

stan

ce

(a)

Dis

tanc

e fr

om t

op

of im

age

to w

all

plat

e (b

)

Min

. ce

iling

he

ight

*

Imag

e w

idth

(w

)

Imag

e he

ight

(h

)

Min

. Pr

ojec

tion

di

stan

ce

(a)

Dis

tanc

e fr

om to

p of

imag

e to

wal

l pl

ate

(b)

55

21

2911

1883

894

275

56

21

4911

3885

310

428

0

57

21

8811

5886

911

328

4

58

22

0811

7988

412

228

9

59

2073

1271

794

6826

222

2811

9989

913

129

3

60

2090

1292

808

7626

622

4812

1991

414

029

720

7813

2874

790

314

61

2107

1314

821

8427

022

6712

4093

014

930

220

9513

5076

098

319

62

2125

1335

835

9227

422

8712

6094

515

830

621

1213

7377

210

632

4

63

2142

1357

848

100

278

2307

1280

960

168

311

2129

1395

785

114

329

64

2160

1379

862

108

282

2326

1300

975

177

315

2146

1417

797

123

333

65

2177

1400

875

117

286

2346

1321

991

186

320

2163

1439

809

131

338

66

2194

1422

888

125

290

2366

1341

1006

195

324

2181

1461

822

139

343

67

2212

1443

902

133

294

2385

1361

1021

204

329

2198

1483

834

148

348

68

2229

1465

915

141

298

2405

1382

1036

213

333

2215

1505

847

156

352

69

2247

1486

929

149

302

2425

1402

1052

223

338

2232

1528

859

164

357

70

2264

1508

942

157

306

2444

1422

1067

232

342

2249

1550

872

173

362

71

2281

1529

956

165

310

2464

1443

1082

241

346

2267

1572

884

181

366

72

2299

1551

969

173

313

2487

1463

1097

250

351

2284

1594

897

189

371

73

2316

1572

983

181

317

2504

1483

1113

259

355

2301

1616

909

198

376

74

2334

1594

996

189

321

2523

1504

1128

268

360

2318

1638

921

206

381

75

2351

1615

1010

197

325

2510

1524

1143

277

364

2335

1660

934

214

385

15

Engl

ish

* Ba

sed

on a

n im

age

762

mm

from

the

floor

; if t

he im

age

is lo

wer

, the

min

imum

cei

ling

heig

ht is

redu

ced

by th

e co

rres

pond

ing

mea

sure

men

t.

76

2368

1637

1023

205

329

2543

1544

1158

287

369

2352

1682

946

223

390

77

2386

1659

1037

214

333

2563

1565

1173

296

373

2370

1705

959

231

395

78

2403

1680

1050

222

337

2582

1585

1189

305

378

2387

1727

971

239

400

79

2420

1702

1063

230

341

2602

1605

1204

314

382

2404

1749

984

247

404

80

2438

1723

1077

238

345

2622

1626

1219

323

389

2421

1771

996

256

409

81

2455

1745

1090

246

349

2641

1646

1234

332

391

2438

1793

1009

264

414

82

2473

1766

1104

254

353

2661

1666

1250

342

395

2456

1815

1021

272

418

83

2490

1788

1117

262

357

2681

1687

1265

351

400

2473

1837

1034

281

423

84

2507

1809

1131

270

361

2700

1707

1280

360

404

2490

1860

1046

289

428

85

2525

1831

1144

278

365

2720

1727

1295

369

409

2507

1882

1058

297

433

86

2542

1852

1158

286

369

25

2419

0410

7130

643

7

87

2560

1874

1171

294

372

25

4219

2610

8331

444

2

88

2577

1895

1185

303

376

25

5919

4810

9632

244

7

89

2594

1917

1198

311

380

25

7619

7011

0833

145

2

90

2612

1939

1212

319

384

25

9319

9211

2133

945

6

91

2629

1960

1225

327

388

26

1020

1511

3334

746

1

92

2647

1982

1239

335

392

26

2720

3711

4635

646

6

93

2664

2003

1252

343

396

26

4520

5911

5836

447

1

94

2681

2025

1265

351

400

95

2699

2046

1279

359

404

96

2716

2068

1292

367

408

Dia

gona

l im

age

size

(S

)

16:1

0 W

XGA

for B

righ

tLin

k 45

0Wi,

Pow

erLi

te 4

50W

, and

Pow

erLi

te 4

60

4:3

XGA

for B

righ

tLin

k 45

0Wi a

nd

Pow

erLi

te 4

50W

16:9

Wid

escr

een

for B

righ

tLin

k 45

0Wi,

Pow

erLi

te 4

50W

, and

Pow

erLi

te 4

60

Min

. ce

iling

he

ight

*

Imag

e w

idth

(w

)

Imag

e he

ight

(h

)

Min

. pr

ojec

tion

di

stan

ce

(a)

Dis

tanc

e fr

om to

p of

imag

e to

wal

l pl

ate

(b)

Min

. ce

iling

he

ight

*

Imag

e w

idth

(w

)

Imag

e he

ight

(h

)

Min

. pr

ojec

tion

di

stan

ce

(a)

Dis

tanc

e fr

om t

op

of im

age

to w

all

plat

e (b

)

Min

. ce

iling

he

ight

*

Imag

e w

idth

(w

)

Imag

e he

ight

(h

)

Min

. Pr

ojec

tion

di

stan

ce

(a)

Dis

tanc

e fr

om to

p of

imag

e to

wal

l pl

ate

(b)

16

*Based on an image 30 inches (762 mm) from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

4:3 XGA for PowerLite 460 in inches (and millimeters)

S w h a bDiagonal

image sizeMinimum

Ceiling Height*Image width Image height Minimum Projection

Distance (Wide)Distance from top of image to wall plate

63" 85.0 (2160) 50.4 (1280) 37.8 (960) 2.8 (71) 7.3 (184)

64" 85.7 (2178) 51.2 (1300) 38.4 (975) 3.1 (79) 7.3 (187)

65" 86.4 (2196) 52.0 (1321) 39.0 (991) 3.4 (87) 7.4 (189)

66" 87.1 (2213) 52.8 (1341) 39.6 (1006) 3.7 (94) 7.5 (191)

67" 87.8 (2231) 53.6 (1361) 40.2 (1021) 4.0 (102) 7.6 (194)

68" 88.5 (2249) 54.4 (1382) 40.8 (1036) 4.3 (110) 7.7 (196)

69" 89.2 (2266) 55.2 (1402) 41.4 (1052) 4.6 (117) 7.8 (199)

70" 89.9 (2284) 56.0 (1422) 42.0 (1067) 4.9 (125) 7.9 (201)

71" 90.6 (2302) 56.8 (1443) 42.6 (1082) 5.2 (133) 8.0 (204)

72" 91.3 (2319) 57.6 (1463) 43.2 (1097) 5.5 (140) 8.1 (206)

73" 92.0 (2337) 58.4 (1483) 43.8 (1113) 5.8 (148) 8.2 (208)

74" 92.7 (2355) 59.2 (1504) 44.4 (1128) 6.1 (155) 8.3 (211)

75" 93.4 (2372) 60.0 (1524) 45.0 (1143) 6.4 (163) 8.4 (213)

76" 94.1 (2390) 60.8 (1544) 45.6 (1158) 6.7 (171) 8.5 (216)

77" 94.8 (2408) 61.6 (1565) 46.2 (1173) 7.0 (178) 8.6 (218)

78" 95.5 (2425) 62.4 (1585) 46.8 (1189) 7.3 (186) 8.7 (221)

79" 96.2 (2443) 63.2 (1605) 47.4 (1204) 7.6 (194) 8.8 (223)

80" 96.9 (24461 64.0 (1626) 48.0 (1219) 7.9 (201) 8.9 (226)

81" 97.6 (2478) 64.8 (1646) 48.6 (1234) 8.2 (209) 9.0 (228)

82" 98.3 (2496) 65.6 (1666) 49.2 (1250) 8.5 (216) 9.1 (230)

83" 99.0 (2514) 66.4 (1687) 49.8 (1265) 8.8 (224) 9.2 (233)

84" 99.7 (2531) 67.2 (1707) 50.4 (1280) 9.1 (232) 9.3 (235)

85" 100.4 (2549) 68.0 (1727) 51.0 (1295) 9.4 (239) 9.4 (238)

86" 101.1 (2567) 68.8 (1748) 51.6 (1311) 9.7 (247) 9.5 (240)

87" 101.8 (2584) 69.6 (1768) 52.2 (1326) 10.0 (255) 9.6 (243)

88" 102.4 (2602) 70.4 (1788) 52.8 (1341) 10.3 (262) 9.7 (245)

89" 103.1 (2620) 71.2 (1808) 53.4 (1356) 10.6 (270) 9.7 (247)

90" 103.8 (2638) 72.0 (1829) 54.0 (1372) 10.9 (277) 9.8 (250)

91" 104.5 (2655) 72.8 (1849) 54.6 (1387) 11.2 (285) 9.9 (252)

92" 105.2 (2673) 73.6 (1869) 55.2 (1402) 11.5 (293) 10.0 (255)

93" 105.9 (2691) 74.4 (1890) 55.8 (1417) 11.8 (300) 10.1 (257)

94" 106.6 (2708) 75.2 (1910) 56.4 (1433) 12.1 (308) 10.2 (260)

95" 107.3 (2726) 76.0 (1930) 57.0 (1448) 12.4 (316) 10.3 (262)

96" 108.0 (2744) 76.8 (1951) 57.6 (1463) 12.7 (323) 10.4 (265)

97" 108.7 (2761) 77.6 (1971) 58.2 (1478) 13.0 (331) 10.5 (267)

98" 109.4 (2779) 78.4 (1991) 58.8 (1494) 13.3 (339) 10.6 (269)

99" 110.1 (2797) 79.2 (2012) 59.4 (1509) 13.6 (346) 10.7 (272)

100" 110.8 (2814) 80.0 (2032) 60.0 (1524) 13.9 (354) 10.8 (274)

101" 111.5 (2832) 80.8 (2052) 60.6 (1539) 14.2 (361) 10.9 (277)

102" 112.2 (2850) 81.6 (2073) 61.2 (1554) 14.5 (369) 11.0 (279)

17

Engl

ish

If you have a pre-existing whiteboard, refer to the table below to identify common models and sizes. If your board is listed here, use the dimensions to reference the installation requirements found on pages 12 to 16.

Interactive whiteboard sizes

Diagonal size 16:10 WXGA 4:3 XGA 16:9 Widescreen

60 inches RM ClassBoard2 60

63 inches Hitachi StarBoard FX-63

64 inches SMART Board 660Promethean ActivBoard 164

71 inches INTERWRITE BOARD 1071

77 inches Hitachi Cambridge Board 77Hitachi StarBoard FX-77SMART Board 680

77.5 inches RM ClassBoard2 77.5INTERWRITE BOARD 1077

78 inches PolyVision TS 600/ TS610 / TSL610/ENO 2610

PolyVision TS610Promethean ActivBoard 178 / 378

82 inches Hitachi StarBoard FX-82W

85 inches INTERWRITE BOARD 1085

87 inches SMART Board 685 Promethean ActivBoard 387

93 inches PolyVision ENO 2810

94 inches SMART Board 690

96 inches Epson BrightLink 450Wi

18

5. Installing the Projector

Make sure to follow the steps below to install the setting plate. If you ignore these steps, the setting plate could fall and cause personal injury or property damage.

A Install the wall plate on the wall(1) Determine the template sheet position.

From the tables on pages 12 to 16, confirm the screen size (S) and the distance between the projection surface and wall plate (b).

Align the CTR line (vertical) of the template sheet with the center line (vertical) of the projection surface.Confirm where the beams or studs are within the wall, and shift the position left or right as necessary.The position can be shifted horizontally left or right from the center line of the projection surface by up to 1.77 in. (45 mm).

Align the line (horizontal) on the template with the height of (b).

The maximum combined weight of the setting plate and the projector is approximately 33.5 lb (15.2 kg). When you install the setting plate, calculate the permissible weight, carefully check the construction, material, and strength of the wall, and perform the installation properly using the most appropriate method.

Center line of projection surface

CTR line of template sheet

line on template sheet

65 mm (2.55 in.)

19

Engl

ish

(2) Attach the template sheet to the wall.If you need to install a junction box, you can use the cutout areas in the wall plate for the box. The junction box needs to be recessed into the wall if you want to use the wall plate cover.

(3) Make mounting holes in the wall in the required locations.The wall plate needs to be secured by commercially available anchors or lag bolts in the following places. It is recommended that the wall plate be secured in at least three places. If securing the wall plate in four places, make the holes indicated by A or B in the figure.

If securing the wall plate in three places, make the holes indicated by C in the figure.

(4) Remove the template sheet. (5) Mount the wall plate on the wall.

B Determine the projection distance and pull out the slider(1) Using the tables on pages 12 to 16, calculate the distance (a) from the projection surface to

the front of the projector.(2) Loosen the four screws and pull out the slider on the setting plate.

When you mount the projector on the wall with the setting plate, the wall needs to be strong enough to hold the projector and the setting plate. Confirm the weight of the projector and the setting plate before installation, and maintain the strength of the wall. If the wall is not strong enough, reinforce the wall before installation.

Install the setting plate so that it can sufficiently support the weight of the projector and setting plate, and resist any horizontal vibration. Use M8 nuts and bolts. Nuts and bolts smaller than M8 could cause the setting plate to fall.

Epson takes no responsibility for any damage or injury caused by incorrect installation.

Warning

Four mounting holes Three mounting holes

20

Align the slider with the mark on the slider measure that is a distance (a+x) equivalent to the distance (a) plus the thickness of the board (x). See the tables on pages 12 to 16. The recommended range for projection distance (a) is 2.76 to 14.57 in. (7 to 37 cm).

C Attach the setting plate to the wall plate(1) Position the cables between the two screws and pass the cables through the setting plate

(A).

(2) Hang the setting plate hook onto the wall plate bar (B).

(3) Tighten the two M8 x 15 mm hexagon socket head cap bolts and two M8 x 45 mm hexagon socket head cap bolts supplied with the setting plate so that the setting plate becomes vertical against the wall (C).Use the two M8 x 45 mm hexagon socket head cap bolts to adjust the vertical position.s 26

Screws (4 )

Slider measure

Take care not to trap the cables between the setting plate and wall plate.

Caution

Setting plate

Cables

Wall plate

M8 x 15 mm hexagon socket head cap bolts (one on left and one on right)

Wall plate bar

M8 x 45 mm hexagon socket head cap bolts (2)

Setting plate hook

21

Engl

ish

D Secure the projector to the setting plate(1) Loosen the two screws and remove the cable cover from the projector.

(2) Insert the slide plate into the setting plate from the interface side of the projector (A).Align the marks on the projector and the setting plate (B).

(3) Tighten the two M5 x 12 mm hexagon socket head cap bolts (C).

Cable coverScrews (2)

Projectorinterface side

M5 x 12 mm hexagon socket head cap bolts (2)

Marks

Bolt positions

Slide plate

If you use adhesives to prevent the screws from loosening or things such as lubricants or oils on the slide plate, the case may crack and cause the projector to fall, resulting in personal injury or property damage. Do not use adhesives, lubricants, or oils to install or adjust the setting plate.

Warning

22

E Connect the power cable and other cables to the projectorConnect any necessary cables such as the power cable, computer cable, and USB cable to the projector.

If you are planning to run the cables inside the wall, make sure you follow all local electrical codes. If you are running the cables outside the wall, use a cable management system to keep the cables from obstructing the image. An optional cable management system is available from Epson (part # ELPCK01).

6. Adjusting the Image

To ensure maximum projection screen quality, follow the steps below to adjust the projected image.

A Turn on the projector

Do not make adjustments with the Keystone function of the projector. Doing so may result in a reduction in image quality.

Using Remote Control Using Control Panel

Power cable

Computer cable

USB cable

23

Engl

ish

B Display the test patternPress the Menu button and select the Settings menu - Pattern - Test Pattern. The test pattern is optimized for a WXGA (16:10) image on the BrightLink 450Wi and the PowerLite 450W. The test pattern is optimized for an XGA image on the PowerLite 460. If you want to change the aspect ratio, you need to connect a computer and project an actual image.

To project an image from a laptop, you may need to Hold down the Fn key on the keyboard and press the function key that lets you display on an external monitor. It may have an icon, or it may be labelled CRT/LCD. You may need to hold down the Fn key while pressing it. s Users Guide for the projector: Settings menu

C Change the aspect ratio if necessaryYou must connect a computer before you can change the aspect ratio. Each time you press the Aspect button on the remote control, the aspect name is displayed on the screen and the aspect ratio changes.

Change the setting according to the signal for the connected equipment.

Alternatively, set the aspect ratio from the Signal menu - Aspect. Following is a list of available aspect settings:

PowerLite 460 4:3: Displays images using the full projection area and maintains the aspect ratio of the image.

Choose this setting to automatically resize the image and make the best use of the display area.

16:9: Converts the aspect ratio of the image to 16:9. 4:3 ratio images are elongated horizontally to fit.

BrightLink 450Wi and PowerLite 450W Normal: Displays images using the full projection area and maintains the aspect ratio of the image.

Choose this setting to automatically resize the image and make the best use of the display area.

16:9: Converts the aspect ratio of the image to 16:9. 4:3 ratio images are elongated horizontally to fit. Full: Displays images using the full width of the projection area, but does not retain the aspect ratio.

4:3 ratio images are elongated horizontally.

Zoom: Displays images using the full width of the projection area and maintains the aspect ratio of the image. The image may be cut off on the top and bottom depending on its aspect ratio.

Native: Displays images as is (aspect ratio and resolution are maintained). Black bands may appear or images may be cut off, depending on the resolution.

s Users Guide for the projector: Configuration menu - Signal menu

Using Remote Control Using Control Panel

Remote Control

Full

Aspect Ratio

24

D Adjust the focus(1) Move the air filter cover lever to open the air filter cover.(2) Use the focus lever to adjust the focus.

(3) After you finish making the adjustment, close the air filter cover.You may need to adjust the focus again after you adjust the image position.

E Use the left adjustment dial to adjust the horizontal roll(1) Loosen the screw that corresponds to the left adjustment dial (A).

(2) Turn the adjustment dial to adjust the horizontal roll (B).

(3) After you finish making all of the adjustments in steps E to I, tighten the screw you loosened in A.

Focus lever

Air filter cover

Air filter cover lever

25

Engl

ish

F Use the right adjustment dial to adjust the horizontal rotation(1) Loosen the two screws that correspond to the right adjustment dial (A).

(2) Turn the adjustment dial to adjust the horizontal rotation (B).

(3) After you finish making all of the adjustments in steps E to I, tighten the two screws you loosened in A.

G Use the top adjustment dial to adjust the vertical tilt

(1) Loosen the screw that corresponds to the top adjustment dial (A).

(2) Turn the adjustment dial to adjust the vertical tilt (B).

(3) After you finish making all of the adjustments in steps E to I, tighten the screw you loosened in A.

Repeat steps E to I as necessary.

26

H Adjust the vertical position(1) Adjust the vertical position, then tighten the two M8 x 15 mm hexagon socket head cap

bolts on the sides of the setting plate (A). (2) Tighten the two M8 x 45 mm hexagon socket head cap bolts at the bottom of the setting

plate to support your vertical adjustment (B). The projected image is raised or lowered accordingly. After you make this adjustment, you may need to readjust the vertical tilt, as described on page 25.

I Adjust the forward/backward slideLoosen the four screws and adjust the slider of the setting plate.

After you finish making all of the adjustments in steps E to I, tighten the screws.

J Turn off the display of the test pattern or computer imagePress the Esc button on the remote control or control panel to turn off the test pattern.

M8 x 45 mmhexagon socket head cap bolts (2)

Screws (4)

Tighten all screws firmly. If the screws are not tightened firmly, the projector or setting plate may fall and cause personal injury or property damage.

Warning

27

Engl

ish

7. Attaching the Covers

A Attach the wall plate cover and end cap(1) Secure the wall plate cover with the two M4 x 12 mm hexagon socket head cap bolts (A).

(2) Place the end cap with the concave portion facing up (B).

B Attach the cable cover to the projectorAttach the cable cover and tighten the two screws to secure the cable cover.

qIf the cables are not installed inside the wall, you need to pass them through thecutouts on each side of the wall plate cover. You may need to enlarge the cutouts toallow the cables to be passed through.

End cap

Wall plate cover

M4 x 12 mmhexagon socket head cap bolts (2)

Cable cutouts

Cable cover

Screws (2)

Only a specialist should remove or reinstall the projector, including for maintenance and repairs. Refer to the Users Guide of your projector for instructions on maintenance and repairs.

28

8. Appendix

Using the Easy Interactive Function (BrightLink 450Wi Only)After you install the BrightLink 450Wi, you need to install the Easy Interactive Driver and perform calibration (to align the positions of the cursor and Easy Interactive Pen).

For details, refer to the supplied Quick Guide or the Users Guide on the BrightLink 450Wi CD-ROM.

Attaching a Security CableIf the projector is to be installed in a room where it will be left unattended, you can use a commercially available theft-prevention wire lock to secure the projector to a post or other object to prevent someone from taking it.

Pass the wire of the theft-prevention wire lock through the security cable installation point.

For details on how to lock the wire lock, refer to the Users Guide supplied with the wire lock.

Never loosen the bolts and nuts after installation. Confirm that the screws have not become loose on a regular basis. If you find any loose screws, tighten them firmly. If the screws are not tightened firmly, the projector or setting plate may fall and cause personal injury or property damage.

Do not hang on the setting plate or hang a heavy object on the setting plate. If the projector or setting plate falls, it could cause personal injury or property damage.

Warning

After installation of the BrightLink 450Wi is complete , make sure you leave the pens, remote control, batteries, software CDs, and Quick Guide in the room with the projector.

29

Fran

ais

Consignes de scurit

Pour votre scurit, veuillez lire toutes les consignes contenues dans ce guide avant dutiliser le support de montage. Une manipulation incorrecte ne respectant pas ces consignes pourrait endommager le support de montage ou provoquer des blessures corporelles ou des dommages matriels. Conservez ce guide dinstallation porte de main pour pouvoir vous y reporter ultrieurement.

Lisez les Consignes de scurit de votre projecteur dans le Guide de lutilisateur et suivez les instructions figurant dans ce document.

Explication des symbolesLes symboles davertissement ci-dessous sont utiliss dans ce guide dinstallation afin de vous viter de vous blesser ou de provoquer des dommages matriels. Assurez-vous de bien avoir compris la signification de ces avertissements lorsque vous lisez ce guide.

Consignes de scurit pour linstallation

Ce symbole signale des informations qui, si elles sont ignores, peuvent provoquer des blessures, voire la mort, en raison dune manipulation incorrecte.

Ce symbole indique des informations qui, si elles sont ignores, peuvent provoquer des blessures ou des dommages physiques, en raison dune manipulation incorrecte.

Symbole indiquant une action ne pas faire

Symbole indiquant une action faire

Le support de montage est conu exclusivement pour fixer un projecteur un mur. Si un quipement autre quun projecteur est install, son poids peut endommager le support.En cas de chute du support de montage, il peut provoquer des blessures corporelles ou des dommages matriels.

Les travaux dinstallation (fixation murale) doivent tre effectus par des spcialistes disposant des comptences techniques et du savoir-faire appropris. Une installation incomplte ou incorrecte peut entraner la chute du support de montage et provoquer des blessures corporelles ou des dommages matriels. Contactez le bureau du service dassistance la clientle rpertori dans la section Comment obtenir de laide du Guide de lutilisateur de votre projecteur pour installer le support de montage.

Suivez les instructions du prsent guide pour installer le support de montage.En cas de non-respect des instructions, le support de montage peut tomber et provoquer des blessures corporelles ou des dommages matriels.

Manipulez le cble dalimentation avec prcaution.Une manipulation incorrecte peut provoquer un incendie ou une lectrocution. Prenez les prcautions suivantes en le manipulant : Ne saisissez pas la fiche secteur avec des mains humides. Nutilisez pas un cble dalimentation endommag ou modifi. Ne tirez pas exagrment sur le cordon lorsque vous le faites passer travers le support de montage.

La fixation du projecteur sur un mur laide du support de montage doit tre effectue sur un mur suffisamment solide pour maintenir le support de montage et le projecteur. Vrifiez donc le poids du projecteur et du support de montage avant linstallation et veillez la bonne solidit du mur. Si la solidit du mur est insuffisante, renforcez le mur avant de procder linstallation.

Ninstallez pas le support de montage un endroit o il peut tre soumis des vibrations ou des chocs.Des vibrations ou des chocs pourraient endommager le projecteur ou la surface de montage. Vous risqueriez galement de provoquer la chute du support de montage ou du projecteur et donc des blessures corporelles ou des dommages matriels.

Installez le support de montage de sorte quil puisse supporter son poids ainsi que celui du projecteur et rsister toute vibration horizontale. Utilisez des crous et des boulons M8.Si vous utilisez des crous et des boulons de taille infrieure M8, le support de montage risque de tomber. Epson dcline toute responsabilit en cas de dommage ou de blessure d une mauvaise installation.

Avertissement

Attention

Avertissement

30

Emplacement

Avant dinstaller le projecteur, vrifiez le cblage de lalimentation lectrique de lemplacement dinstallation.

loignez le projecteur des autres appareils lectriques, notamment des clairages fluorescents ou des climatiseurs. Certains types dclairages fluorescents risquent dinterfrer avec la tlcommande du projecteur.

Nous vous recommandons dutiliser un cble de connexion dune longueur infrieure 20 mtres (65 pieds) afin de rduire leffet de parasites.

Installez le support de montage dans un endroit labri de la poussire et de lhumidit pour que lobjectif et les lments optiques internes ne se salissent pas.

propos de ce guide dinstallation

Le prsent guide dcrit comment installer le projecteur courte distance de projection BrightLink 450 Wi, PowerLite 460 et PowerLite 450W sur un mur laide du support de montage prvu exclusivement cet effet.

Linstallation doit tre excute par au moins deux techniciens qualifis. Si vous devez desserrer des vis pendant linstallation, veillez ne pas provoquer la chute du support de montage.En cas de chute du support de montage ou du projecteur, il peut provoquer des blessures corporelles ou des dommages matriels.

Contrlez rgulirement le support de montage pour vrifier quaucune de ses pices nest endommage ou que des vis ne sont pas desserres.Si des pices sont endommages, cessez immdiatement dutiliser le support de montage. En cas de chute du support de montage ou du projecteur, il peut provoquer des blessures corporelles ou des dommages matriels.

Ne modifiez jamais le support de montage.

Ne suspendez aucun objet au support de montage ni ne posez dobjet lourd sur celui-ci.En cas de chute du projecteur ou du support de montage, il peut provoquer des blessures corporelles ou des dommages matriels.

Si vous utilisez des adhsifs pour empcher les vis de se desserrer ou si vous utilisez des lubrifiants ou des huiles sur la plaque coulissante de fixation du projecteur, le botier risque de se dtriorer, au risque de provoquer la chute du projecteur et des blessures corporelles ou des dommages matriels. Nutilisez pas dadhsifs, ni dhuiles ou lubrifiants pour installer ou rgler le support de montage.

Serrez fermement toutes les vis aprs tout rglage.Des vis insuffisamment serres peuvent entraner la chute du projecteur ou du support de montage et provoquer des blessures corporelles ou des dommages matriels.

Ne desserrez jamais les crous et les boulons aprs linstallation.Vrifiez rgulirement que les vis ne se sont pas desserres. Si vous constatez le moindre jeu, resserrez fermement les vis concernes. Des vis insuffisamment serres peuvent entraner la chute du projecteur ou du support de montage et provoquer des blessures corporelles ou des dommages matriels.

Ninstallez pas le support de montage dans un endroit qui excde la plage de temprature de fonctionnement du modle de projecteur.Un tel environnement peut endommager le projecteur.

Installez le support de montage dans un endroit labri de la poussire et de lhumidit pour que lobjectif et les lments optiques internes ne se salissent pas.

Ne forcez pas de manire excessive lorsque vous rglez le support de montage.Le support de montage peut tre endommag et provoquer des blessures corporelles.

Avertissement

Attention

31

Fran

ais

1 Contenu de lemballage s Page 32

2 Spcifications s Page 34

3 Connexion des appareils s Page 35

4 Positionnement du projecteur s Page 36(1) Feuille de travail d'installation pour la projection sur un tableau

mural prinstall(2) Feuille de travail d'installation pour la projection sur un mur

ordinaire(3) Mesures dinstallation en pouces(4) Mesures dinstallation en millimtres

5 Installation du projecteur s Page 46(1) Installez la plaque murale sur le mur(2) Dterminez la distance de projection et retirez la glissire(3) Fixez le support de montage la plaque murale(4) Fixez le projecteur au support de montage(5) Connectez le cble dalimentation et les autres cbles au projecteur

6 Rglage de limage s Page 52(1) Mettez le projecteur sous tension(2) Affichez la mire(3) Changez le rapport hauteur/largeur (au besoin)(4) Rglez la mise au point(5) Utilisez la molette de rglage gauche pour rgler le roulis horizontal(6) Utilisez la molette de rglage droite pour rgler la rotation horizontale(7) Utilisez la molette de rglage suprieure pour rgler linclinaison verticale(8) Rglez la position verticale(9) Rglez le coulissement vers lavant/larrire

(10) Dsactivez laffichage de la mire ou limage de lordinateur

7 Fixation des caches s Page 57(1) Fixez le cache de la plaque murale et le capuchon de protection(2) Fixez le cache du cble au projecteur

32

1. Contenu de lemballage

Matriel de montage

Utilisez les boulons fournis avec le support de montage pour installer ce dernier, comme dcrit dans le prsent guide. Ne leur substituez pas un autre type de boulons.

Utilisez des pattes de fixation M8 x 50 mm (3 minimum) ou des tire-fonds 8 x 80 mm (3 minimum), disponibles dans le commerce, pour fixer la plaque murale au mur.

Rassemblez les outils et les lments ncessaires avant de commencer linstallation.

Forme Nom Quantit Application

Boulon tte cylindrique six pans M8 x 15 mm avec rondelle

2 Pour installer le support de montage

Boulon tte cylindrique six pans M5 x 12 mm avec rondelle

2 Pour fixer le projecteur

Boulon tte cylindrique six pans M4 x 12 mm sans rondelle

2 Pour installer le cache de la plaque murale

Cls six pans (pour M4, M5 et M8)

Cache de la plaque murale

Support de montage(support mural)

Fiche modle(pour linstallation de la plaque murale)

Capuchon de protection

Plaque murale

33

Fran

ais

Bote du projecteur

Crayons interactifs et piles AAA*

Cordon dalimentation

Projecteur

CD Epson Projector Software for Easy Interactive Function*

Cble dordinateur VGA

Tlcommande et piles AA

Cble USB*

CD Epson Projector Software for Meeting and Monitoring

Autocollant de scurit CD du

projecteur

*lments inclus seulement pour le projecteur BrightLink 450Wi. Le crayon additionnel et lensemble de piles sont inclus pour les tats-Unis et le Canada seulement.

34

2. Spcifications

Plaque murale

Plage de rglage du support de montage

lment Spcification Remarque Page de rfrence

Poids du support de montage Environ 6,3 kg (13,89 livres)

Plaque murale (2,2 kg [4,85 livres])Caches et capuchon (0,47 kg [1,04 livre])

Plage de rglage du coulissement vers lavant/larrire

0 300 mm (11,81 pouces)

Voir lillustration ci-dessous

Plage de rglage du coulissement vertical

4 Minimum : 28 mm (1,10 pouce)Maximum : 42,5 mm (1,67 pouce)

s 56

Plage de rglage de linclinaison verticale

5 Rglages prcis possibles avec la molette de rglage

s 55

Plage de rglage de la rotation horizontale

5 Rglages prcis possibles avec la molette de rglage

s 55

Plage de rglage du roulis horizontal

3 Rglages prcis possibles avec la molette de rglage

s 54

Plage de rglage du coulissement horizontal

45 mm (1,77 pouce)

Voir lillustration ci-dessous

[Unit : mm (pouce)] 250 (9,87)

456 (17,97)

230 (9,05)

222 (8,74)

160 (6,3)

247 (9,71)

15 (0,59) 112 (4,4)

203,2 (8 )

121(4,75)

76 (3,0)

46 (1,8)46 (1,81)

Plage de rglage du coulissement vers lavant/larrire :0 300 mm (11,81 pouces)

Plage de rglage du coulissement horizontal : 45 mm (1,77 pouce)

35

Fran

ais

3. Connexion des appareils

Assurez-vous davoir le cble dalimentation, le cble dordinateur, le cble USB et les autres pices, lemplacement dinstallation du support de montage.

Assurez-vous davoir tous les cbles ncessaires pour tous les appareils, une camra document ou un microphone par exemple, que vous envisagez de connecter au projecteur.

Exemple de connexion

Haut-parleurs externes Appareil rseau local

Microphone

Cble USB(pour Easy Interactive Function)

Camra document

Ordinateur

Cble dordinateur(pour la sortie vido de lordinateur)

Cble USB ddi(fourni avec la camra document)

Cble audio(disponible dans le commerce)

Cble rseau local

Cble dalimentation

36

4. Positionnement du projecteur

Les projecteurs BrightLink 450Wi et PowerLite 450W peuvent projeter jusqu' 96 pouces (diagonale) en format image WXGA ou jusqu' 85 pouces (diagonale) en format image XGA. Le projecteur PowerLite 460 peut projeter jusqu'a 102 pouces (diagonale) en format image XGA. Vous pouvez projeter sur un tableau blanc prinstall ou directement sur un mur ordinaire. C'est la hauteur du support mural qui dtermine la taille d'image maximum et la hauteur laquelle l'image est projete sur le mur ou le tableau blanc. La distance du projecteur du mur (une fois qu'il est mont sur le bras rglable de la plaque de fixation) influe aussi sur la taille et la position de l'image.

Si vous planifiez de projeter sur un tableau blanc, il est possible que l'image n'occupe pas tout le tableau; tout dpend du rapport hauteur/largeur. Si vous faites correspondre la hauteur de l'image la hauteur du tableau, il est possible que des espaces apparaissent sur les cts du tableau.

Utilisez les feuilles de travail suivantes pour dterminer l'emplacement appropri de la plaque murale sur le mur. Si vous projetez sur un tableau blanc prinstall, utilisez la feuille de travail ci-dessous. Si vous projetez sur un mur ordinaire, utilisez la feuille de travail de la page 38.

Feuille de travail d'installation pour la projection sur un tableau mural prinstall

(1) Mesurez la hauteur du plafond (distance du plancher au plafond).

(2) Mesurez la hauteur de la zone d'image du tableau (h).

(3) Mesurez la largeur de la zone d'image du tableau (l).

(4) Mesurez la distance du plancher au bas de la zone d'image du tableau (f ).

(5) Mesurez la distance du plafond au sommet de la zone d'image du tableau (c).

(6) Mesurez l'paisseur du tableau (x).

_____

_____ (h)

_____ (l)

_____ (f )

_____ (c)

_____ (x)

37

Fran

ais

(7) Dterminez le rapport d'aspect du tableau ou des images projeter. Pour de nouveaux ordinateurs ou portatifs, il s'agira probablement de WXGA (16:10). Pour l'quipement plus ancien, il s'agira probablement de XGA (4:3). Il vous faudra peut-tre consulter votre directeur en TI pour obtenir cette information.

4:3 XGA 16:10 WXGA 16:9 grand cran

(8) En utilisant les tableaux des pages 40 44 pour votre rapport d'aspect et la hauteur d'image souhaite (h), trouvez la distance requise entre le sommet de la zone d'image et la plaque murale (b).

(9) Dterminez la position pour l'installation de votre projecteur en additionnant les valeurs (f ), (h) et (b), en prvoyant 254 mm (10 po) de plus pour la hauteur de la plaque murale et le couvercle.

Si la hauteur du plafond de votre salle (telle que note l'tape 1) ne correspond pas la hauteur de plafond minimum requise pour votre tableau, vous pourriez avoir besoin de slectionner une taille d'image plus petite ou d'abaisser le tableau sur le mur.

(10)Aprs avoir confirm votre taille d'image, utilisez du ruban ou un crayon pour marquer la distance (b) du sommet de la zone d'image sur le tableau au bas.

(11)Alignez la ligne horizontale (horizontal) sur le gabarit avec la marque (b), puis alignez la ligne centrale du gabarit avec le centre de la zone d'image. Suivez les directives de la page 46 pour installer le projecteur.

254 mm (10 po)hauteur de la plaque murale plus couvercle

Distance requise du sommet de la zone d'image la plaque murale (b)

Taille diagonale de la zone d'image (s)

Hauteur de la zone d'image (h)

Distance du plafond au sommet de la zone d'image (c)

Largeur de la zone d'image (l)

Distance du plancher au bas de la zone d'image (f)

_____ (b)

_____ (f )

_____ (h)

_____ (b)

+254 mm(10 po)

_____ total

38

Feuille de travail d'installation pour la projection sur un mur ordinaire(1) Mesurez la hauteur du plafond (distance du plancher au plafond).

(2) Dterminez le rapport d'aspect souhait de l'image. Pour de nouveaux ordinateurs ou portatifs, il s'agira probablement de WXGA (16:10). Pour l'quipement plus ancien, il s'agira probablement de XGA (4:3). Il vous faudra peut-tre consulter votre directeur en TI pour obtenir cette information.

4:3 XGA 16:10 WXGA 16:9 grand cran

(3) l'aide des tableaux des pages 40 44 pour votre rapport d'aspect, slectionnez la taille d'image la plus grande qui soit disponible pour la hauteur de votre plafond.

Hauteur d'image (h)Largeur d'image (l)

(4) Mesurez la distance souhaite du plancher au bas de la zone d'image (f ).

La distance minimum recommande est de 762 mm (30 po). Il se peut que la vue des images apparaissant moins de 28 pouces du plancher soit obstrue.

(5) Trouvez le sommet de la zone d'image projete en additionnant les distances (f ) et (h).

(6) Utilisez les tableaux des pages 40 44 pour dterminer la distance requise du haut de la zone d'image au bas de la plaque murale (b).

(7) Additionnez : Distance requise du haut de la zone d'image la plaque murale (b)Hauteur de la zone d'image (h)Distance du plancher au bas de la zone d'image (f )Hauteur de la plaque murale plus couvercle

Si le total dpasse la hauteur du plancher, il vous faudra rduire la taille d'image ou rduire la distance du plancher au bas de la zone d'image.

_____

_____ (h)

_____ (l)

_____ (f )

_____

_____ (b)

_____ (b)_____ (h)_____ (f )+254 mm10 po.

_____ total

39

Fran

ais

(8) Aprs avoir confirm votre taille d'image, utilisez du ruban ou un crayon pour marquer la distance (b) du sommet de la zone d'image sur le tableau au bas de la plaque murale.

(9) Alignez la ligne horizontale (horizontal) sur le gabarit avec la marque (b), puis alignez la ligne centrale du gabarit avec le centre de la zone d'image. Suivez les directives de la page 46 pour installer le projecteur.

Les tableaux des pages suivantes fournissent des renseignements d'installation pour toutes les tailles d'image prises en charge. La hauteur de plafond minimum est base sur une image de 762 mm (30 po) du plancher; si l'image est plus basse, la hauteur de plafond minimum est rduite par la mesure correspondante.

Utilisez les feuilles de travail, l'illustration ci-dessous et les renseignements des tableaux aux pages suivantes pour dterminer la distance de projection et le placement de la plaque murale. La plage recommande pour la distance de projection (a) est de 7 37 cm (2,76 14,57 pouces ).

254 mm (10 po)hauteur de la plaque murale plus couvercle

Distance requise du sommet de la zone d'image la plaque murale (b)

Taille diagonale de l'image (s)

Hauteur de plafond

Distance du haut de limage au haut de la zone dimage (c)

Largeur de la zone d'image (l)

Distance du plancher au bas de la zone d'image (f)

Hauteur de la zone d'image (h)

Plaque murale

Surface de projection

Valeur de dport pour la positiondu centre de l'cran et le centre de la plaque murale

Distance du mur de la surface de projection ou du tableau blanc

65 mm (2,55 po)

254 mm (10 po)

Ligne horizontale

40

Mes

ures

din

stal

lati

on e

n po

uces

Taill

e de

li

mag

e di

agon

ale

(S)

16:1

0 W

XGA

pou

r Bri

ghtL

ink

450W

i, Po

wer

Lite

450

W e

t Pow

erLi

te 4

60

4:3

XGA

pour

Bri

ghtL

ink

450W

i et

Po

wer

Lite

450

W

16:9

gra

nd

cran

pou

r Bri

ghtL

ink

450W

i, Po

wer

Lite

450

W e

t Pow

erLi

te 4

60

Hau

teur

du

pl

afon

d m

in.*

Larg

eur

de

lim

age

(l)

Hau

teur

de

li

mag

e (h

)

Dis

tanc

e de

pr

ojec

tion

m

in.

(a)

Dis

tanc

e du

hau

t de

li

mag

e

la p

laqu

e m

ural

e (b

)

Hau

teur

du

pl

afon

d m

in.*

Larg

eur

de

lim

age

(l)

Hau

teur

de

li

mag

e(h

)

Dis

tanc

e de

pr

ojec

tion

m

in. (

a)

Dis

tanc

e du

hau

t de

lim

age

la

pl

aque

m

ural

e (b

)

Hau

teur

du

pl

afon

d m

in.*

Larg

eur

de

lim

age

(l)

Hau

teur

de

li

mag

e (h

)

Dis

tanc

e de

pr

ojec

tion

m

in. (

a)

Dis

tanc

e du

hau

t de

lim

age

la

pla

que

mur

ale

(b)

55 p

o

83,8

44,0

33,0

3,7

10,8

56 p

o

84,6

44,8

33,6

4,1

11,0

57 p

o

85,4

45,6

34,2

4,4

11,2

58 p

o

86,2

46,4

34,8

4,8

11,4

59 p

o 81

,650

,031

,32,

710

,386

,947

,235

,45,

211

,5

60 p

o 82

,350

,931

,83,

010

,587

,748

,036

,05,

511

,781

,852

,329

,43,

512

,4

61 p

o 83

,051

,732

,33,

310

,688

,548

,836

,65,

911

,982

,553

,229

,93,

912

,6

62 p

o 83

,752

,632

,93,

610

,889

,349

,637

,26,

212

,183

,154

,030

,44,

212

,8

63 p

o 84

,353

,433

,44,

011

,090

,050

,437

,86,

612

,283

,854

,930

,94,

512

,9

64 p

o 85

,054

,333

,94,

411

,190

,851

,238

,47,

012

,484

,555

,831

,44,

813

,1

65 p

o 85

,755

,134

,44,

611

,391

,652

,039

,07,

312

,685

,256

,731

,95,

213

,3

66 p

o 86

,456

,035

,04,

911

,492

,452

,839

,67,

712

,885

,957

,532

,45,

513

,5

67 p

o 87

,156

,835

,55,

211

,693

,153

,640

,28,

012

,986

,558

,432

,85,

813

,7

68 p

o 87

,857

,736

,05,

511

,793

,954

,440

,88,

413

,187

,259

,333

,36,

213

,9

69 p

o 88

,458

,536

,65,

911

,994

,755

,241

,48,

813

,387

,960

,133

,86,

514

,1

70 p

o 89

,159

,437

,16,

212

,095

,556

,042

,09,

113

,588

,661

,034

,36,

814

,2

71 p

o 89

,860

,237

,66,

512

,296

,256

,842

,69,

513

,689

,261

,934

,87,

214

,4

72 p

o 90

,561

,138

,26,

812

,397

,057

,643

,29,

813

,889

,962

,835

,37,

514

,6

73 p

o 91

,261

,938

,77,

112

,597

,858

,443

,810

,214

,090

,663

,635

,87,

814

,8

74 p

o 91

,962

,839

,27,

512

,798

,659

,244

,410

,614

,291

,364

,536

,38,

115

,0

75 p

o 92

,663

,639

,77,

812

,899

,360

,045

,010

,914

,391

,965

,436

,88,

415

,2

41

Fran

ais

* Ca

lcul

bas

su

r une

imag

e de

30

pouc

es

par

tir d

u pl

anch

er; s

i lim

age

est p

lus

bass

e, la

hau

teur

min

imal

e du

pla

fond

est

rdu

ite s

elon

la m

esur

e co

rres

pond

ante

.

76 p

o 93

,264

,440

,38,

113

,010

0,1

60,8

45,6

11,3

14,5

92,6

66,2

37,3

8,8

15,4

77 p

o 93

,965

,340

,88,

413

,110

0,9

61,6

46,2

11,7

14,7

93,3

67,1

37,8

9,1

15,5

78 p

o 94

,666

,141

,38,

713

,310

1,7

62,4

46,8

12,0

14,9

94,0

68,0

38,2

9,4

15,7

79 p

o 95

,367

,041

,99,

013

,410

2,4

63,2

47,4

12,4

15,0

94,6

68,9

38,7

9,7

15,9

80 p

o 96

,067

,842

,49,

413

,610

3,2

64,0

48,0

12,7

15,2

95,3

69,7

39,2

10,1

16,1

81 p

o 96

,768

,742

,99,

713

,710

4,0

64,8

48,6

13,1

15,4

96,0

70,6

39,7

10,4

16,3

82 p

o 97

,369

,543

,510

,013

,910

4,8

65,6

49,2

13,5

15,6

96,7

71,5

40,2

10,7

16,5

83 p

o 98

,070

,444

,010

,314

,010

5,5

66,4

49,8

13,8

15,7

97,4

72,3

40,7

11,1

16,7

84 p

o 98

,771

,244

,510

,614

,210

6,3

67,2

50,4

14,2

15,9

98,0

73,2

41,2

11,4

16,9

85 p

o 99

,472

,145

,011

,014

,410

7,1

68,0

51,0

14,5

16,1

98,7

74,1

41,7

11,7

17,0

86 p

o 10

0,1

72,9

45,6

11,3

14,5

99

,475

,042

,212

,017

,2

87 p

o 10

0,8

73,8

46,1

11,6

14,7

10

0,1

75,8

42,7

12,4

17,4

88 p

o 10

1,5

74,6

46,6

11,9

14,8

10

0,7

76,7

43,1

12,7

17,6

89 p

o 10

2,1

75,5

47,2

12,2

14,9

10

1,4

77,6

43,6

13,0

17,9

90 p

o 10

2,8

76,3

47,7

12,6

15,1

10

2,1

78,4

44,1

13,3

18,0

91 p

o 10

3,5

77,2

48,2

12,9

15,3

10

2,8

79,3

44,6

13,7

18,2

92 p

o 10

4,2

78,0

48,8

13,2

15,4

10

3,4

80,2

45,1

14,0

18,3

93 p

o 10

4,9

78,9

49,3

13,5

15,6

10

4,1

81,1

45,6

14,3

18,5

94 p

o 10

5,6

79,7

49,8

13,8

15,8

95 p

o 10

6,3

80,6

50,3

14,2

15,9

96 p

o 10

6,9

81,4

50,9

14,5

16,1

Taill

e de

li

mag

e di

agon

ale

(S)

16:1

0 W

XGA

pou

r Bri

ghtL

ink

450W

i, Po

wer

Lite

450

W e

t Pow

erLi

te 4

60

4:3

XGA

pour

Bri

ghtL

ink

450W

i et

Po

wer

Lite

450

W

16:9

gra

nd

cran

pou

r Bri

ghtL

ink

450W

i, Po

wer

Lite

450

W e

t Pow

erLi

te 4

60

Hau

teur

du

pl

afon

d m

in.*

Larg

eur

de

lim

age

(l)

Hau

teur

de

li

mag

e (h

)

Dis

tanc

e de

pr

ojec

tion

m

in.

(a)

Dis

tanc

e du

hau

t de

li

mag

e

la p

laqu

e m

ural

e (b

)

Hau

teur

du

pl

afon

d m

in.*

Larg

eur

de

lim

age

(l)

Hau

teur

de

li

mag

e(h

)

Dis

tanc

e de

pr

ojec

tion

m

in. (

a)

Dis

tanc

e du

hau

t de

lim

age

la

pl

aque

m

ural

e (b

)

Hau

teur

du

pl

afon

d m

in.*

Larg

eur

de

lim

age

(l)

Hau

teur

de

li

mag

e (h

)

Dis

tanc

e de

pr

ojec

tion

m

in. (

a)

Dis

tanc

e du

hau

t de

lim

age

la

pla

que

mur

ale

(b)

42

Mes

ures

din

stal

lati

on e

n m

illim

tre

sTa

ille

de

lim

age

diag

onal

e (S

)

16:1

0 W

XGA

pou

r Bri

ghtL

ink

450W

i, Po

wer

Lite

450

W e

t Pow

erLi

te 4

60

4:3

XGA

pour

Bri

ghtL

ink

450W

i et

Po

wer

Lite

450

W

16:9

gra

nd

cran

pou

r Bri

ghtL

ink

450W

i, Po

wer

Lite

450

W e

t Pow

erLi

te 4

60

Hau

teur

du

pl

afon

d m

in.*

Larg

eur

de

lim

age

(l)

Hau

teur

de

li

mag

e (h

)

Dis

tanc

e de

pr

ojec

tion

m

in.

(a)

Dis

tanc

e du

hau

t de

li

mag

e

la p

laqu

e m

ural

e (b

)

Hau

teur

du

pl

afon

d m

in.*

Larg

eur

de

lim

age

(l)

Hau

teur

de

li

mag

e (h

)

Dis

tanc

e de

pr

ojec

tion

m

in. (

a)

Dis

tanc

e du

hau

t de

lim

age

la

pla

que

mur

ale

(b)

Hau

teur

du

pl

afon

d m

in.*

Larg

eur

de

lim

age

(l)

Hau

teur

de

li

mag

e (h

)

Dis

tanc

e de

pr

ojec

tion

m

in. (

a)

Dis

tanc

e du

hau

t de

lim

age

la

pla

que

mur

ale

(b)

55 p

o

2129

1118

838

9427

5

56 p

o

2149

1138

853

104

280

57 p

o

2169

1158

869

113

284

58 p

o

2188

1179

884

122

289

59 p

o 20

7312

7179

468

262

2208

1199

899

131

293

60 p

o 20

9012

9280

876

266

2228

1219

914

140

297

2078

1328

747

9031

4

61 p

o 21

0713

1482

184

270

2248

1240

930

149

302

2095

1350

760

9831

9

62 p

o 21

2513

3583

592

274

2267

1260

945

158

306

2112

1373

772

106

324

63 p

o 21

4213

5784

810

027

822

8712

8096

016

831

121

2913

9578

511

432

9

64 p

o 21

6013

7986

210

828

223

0713

0097

517

731

521

4614

1779

712

333

3

65 p

o 21

7714

0087

511

728

623

2613

2199

118

632

021

6314

3980

913

133

8

66 p

o 21

9414

2288

812

529

023

4613

4110

0619

532

421

8114

6182

213

934

3

67 p

o 22

1214

4390

213

329

423