Call 1300 369 273www.enware.com.auEnware Australia Pty Limited 9 Endeavour Rd Caringbah NSW 2229 Australia Ph: +61 2 8556 4000 info@enware.com.au

I00301_Mar 20

Enware Ifo WC Floor Mounting BracketInstallation Guide

IFO98015

Note: Enware Australia advises: 1. Due to ongoing Research and Development, specifications may change without notice ; 2. Component specifications may change on some export models.

This installation information is a guide only. Appropriate fixing method must be determined by site-specific risk assessment.

Kit Contains:

1x Bracket (Aluminium or HDPE Plastic) 4x Pan-to-Bracket Fixing Screws (12G x 50mm CSK) 4x Screw Caps (White) 1x Template

2 Call 1300 369 273 www.enware.com.au

195

70

90

198

110

20

Bolt hole positionsto �x bracketonto �oor

S-Trap Waste Outlet

Foot

of p

an

Front of pan

425

appr

ox.

(Che

ck p

an s

crew

�xi

ng h

ole

loca

tions

on

pan.

)

floor mounting bracket fixing dimensions - set out

www.enware.com.au Call 1300 369 273 3

198

110

40

IFO98015 Floor Mounting Bracket

31

determine fixing methodMeasure set out dimensions for WC pan. Determine waste outlet position (S-Trap or P-Trap outlet installation).

Determine floor fixing requirements. If the toilet has support arms or may have support arms in future (raised height toilet models only), toilet pan must be fixed to floor using pan screws, or the floor mounting bracket.

fixing with floor mounting bracket:Carry out a site risk assessment taking into account the quality, strength and the thickness of mortar bed, the distance to structural concrete slab, and the impact of the penetration of waterproofing membrane. Determine which one of the following installation methods would be suitable, according to the site risk assessment.

IFO98015 bracket dimensions

4 Call 1300 369 273 www.enware.com.au

1. Position the bracket on the floor. SEE SETOUT on page 2.

2. Mark fixing screw holes on bracket, and pre-drill the marked holes.

3. Fix the bracket onto floor using appropriate fixing screws.

4. Ensure the fixing screws can be fixed onto floor material with adequate structural integrity and strength.

Go to Step 8 on page 6.

Floor Surface

12G x 50mm screws to �x pan onto bracket

method 1: fixing with screws

www.enware.com.au Call 1300 369 273 5

(With Waterproofing)

1. Position the bracket on the floor. SEE SETOUT on page 2.

2. Mark fixing bolt holes for the bracket on floor.

3. Where marked, install 4 threaded rods onto structural concrete slab / mortar bed. Ensure threaded rods are long enough so that it protrudes at least 50mm from the finished floor.

4. Apply waterproofing as normal.

5. Once floor is finished, mark 4 bolt holes on bracket, and pre-drill the marked holes.

6. Fix the bracket onto floor using the threaded rods and matching nuts.

7. Cut off any excess threaded rod.

Go to Step 8 on page 6.

Tiles / Vinyl / Floor Surface

Waterproo�ng

12G x 50mm screws to �x pan onto bracket

Mortar Bed / Screed

Concrete SlabThreaded rods�xed to structural concrete slab before waterproo�ng

Bracket �xed onto �oor using threaded rods after �oor is �nished

method 2: fixing with threaded rods (with waterproofing)

6 Call 1300 369 273 www.enware.com.au

installing the pan

8. WC pan should be bedded with silicone sealant. Apply silicone sealant to the entire bottom contact surface of pan and around the perimeter to create a strong bonding between the pan and the floor.

9. Install pan into position.

10. Through the pan fixing holes, pre-drill the bracket using a 4mm drill bit for Aluminium bracket (3mm for HDPE resin bracket). Fix the pan in place using four 12G x 50mm screws supplied. Hand tighten the screws, but do not over-tighten. (Over-tightening screws will cause the ceramic to crack.)

11. Install white screw caps (supplied) onto the heads of fixing screws.

4x 18Gx50mmScrews

(Pre-Drill holes on bracket with 4 mm drill foraluminium, 3mmfor HDPE plastic bracket)

www.enware.com.au Call 1300 369 273 7

12. After pan is levelled, water supply and waste are connected, and the pan is visually inspected for any leaks, install the rear cover to plug the inspection hole. Apply silicone sealant around the rear cover to create a thorough seal between the rear cover, pan and floor. Ensure no gap is left that can let any moisture to get through inside the base of the pan.

install rear cover (S-trap models)

PRODUCT WARRANTY FOR AUSTRALIA Effective 1 September 2014

Enware Australia Pty Limited (ACN 003 988 314) (“we” or “us”) warrants that this product (also referred to as “our goods”) will be free from all defects in materials and workmanship for 12 months from the date of purchase. Our liability under this warranty is limited at our option to the repair or replacement of the defective product or part, the cost of repair of the defective product or part or the supply of an equivalent product or part, in each case if we are satisfied the loss or damage was due to a defect in the materials or workmanship of the product or part. All products must be installed in accordance with the manufacturer’s instructions, the PCA, and AS/NZS3500 including any other applicable regulatory requirements.

exceptionsThis warranty does not apply in respect of any damage or loss due to or arising from:

a) Failure by you or any other person to follow any instructions for use (including instructions and directions relating to the handling, storage, installation, fitting, connection, adjustment or repair of the product) published or provided by us;

b) Failure by you or any other person responsible for the fitting, installation or other work on the product to follow or conform to applicable laws, standards and codes (including the AS/NZ 3500 set of Standards, all applicable State and Territory Plumbing Codes, the Plumbing Code of Australia and directions and requirements of local and other statutory authorities); or

c) Any act or circumstance beyond our control including faulty installation or connection, accident, abnormal use, acts of God, damage to buildings, other structures or infrastructure and loss or damage during product transit or transportation.

making a claimTo make a claim under this warranty you must notify us in writing within 7 days of any alleged defect in the product coming to your attention and provide us with proof of your purchase of the product together with a completed Online Product Service and Warranty Form, available from our website www.enware.com.au/warranty. All notifications and accompanying forms must be sent to us marked for the attention of the Enware Australia Pty Limited, 9 Endeavour Road, Caringbah NSW 2229. We can also be contacted by telephone (1300 369 273) or by email (info@enware.com.au). Your costs in making a claim under this warranty, including all freight, collection and delivery costs, are to be borne and paid by you. We also reserve the right at our cost to inspect any alleged defect in the product wherever it is located or installed or on our premises.

other conditionsExcept as provided or referred to in this document, we accept no other or further liability for any damages or loss (including indirect, consequential or economic loss) and whether arising in contract, tort or otherwise. Any benefits available to you under this warranty are in addition to any non-excludable rights or remedies you may have under applicable legislation, including as a “consumer” under the Australian Consumer Law. To that extent you need to be aware that: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

CL

I003

17

90195

90 mm

195 mm

Enware® IFO98015 Floor Mounting Bracket Template For Ifo WC (S-Trap)

70

Huvudkontor och tillverkning:Tillverkning:Distriktskontor:Norge:

Geberit A/S, Lægaardsvej 26, DK-8520 Lystrup, Tlf. 8674 10 86, www.ifo.dk

70 mm

See Installation Guide for IFO98015 for information on how to install.