enter descriptive title of part - specifiedby · title: enter descriptive title of part author:...
TRANSCRIPT
Whitecroft Lighting LimitedBurlington Street, Ashton-under-Lyne, Lancashire OL7 0AX
Telephone +44 (0)870 5 087 087 Facsimile: +44 (0)870 5 084 210
Registered No. 3848973 England Registered Office: As above
GENERAL INFORMATIONA qualified electrician, in accordance with IEE wiring regulations should carry out connection
to mains wiring.Observe ESD precautions during installation.This unit must be EARTHED.Ensure that the rated voltage and frequency requirements are compatible with the available
mains supply.Cleaning of reflectors and lenses should be carried out using clean, soft and lint free cloths
and anti-static cleaning fluidDo not carry out high voltage insulation test, i.e. 500/1000v this may damage internal
components.
FURTHER INFORMATIONTECHNICAL SUPPORT
Telephone: 0161 331 5700E-mail: [email protected]
http://www.whitecroftlighting.com/
1.
2.3.4.
5.
6.
Installation sheet
Careline
SPECIFICATION:Lamp type: LED
Colour: 4000°K
Finish: White texture
Materials:
Body: Aluminium
Geartrays / Pan: Steel
Diffusers: Acrylic/Polycarbonate
Weight: 50 kgs
Control gear: Dali
Emergency: Integral 3hr/COMEPS
Supply: 240v 50Hz AC
Operating Temperature: 0-25°C
Supply flex: 1.5 - 2.5mm² appropriate to load, run length and electical
protection employed.
Internal wiring: 1.5mm²
Cable entry: From above, into marshalling box
Terminal block: Screw terminals for mains/dali inputs
Ingress protection: IP20
Ceiling compatibility: T15/T25 (special layout required to suit run design)
Plasterboard aperture lined with battens
PK/LEAFLETCLINE Revision: 3 Jan/17
CarelineWhitecroft Lighting Limited
1 Prepare aperture - suspended ceiling grid only
2 Suspend BodyONLY SUSPEND FROM SOLID CEILING. ENSURE
CABLES, ANCHOR POINTS / BOLTS ARE
SUITABLY RATED FOR THE PRODUCTS
WEIGHT. USE A SUITABLY RATED PLATFORM
TO SUPPORT FITTING WHILST DROP RODS /
SUSPENSION WIRES ARE FIXED.
1185
OVER
ALL
FLAN
GE W
IDTH
-
1173
TYPI
CAL
MIN. C
UT A
PERT
URE
-
1785OVERALL FLANGE WIDTH -
TYPICAL MIN. CUT APERTURE - 1770
WIRE SUSPENSION HOOKS (SUPPLIED BY OTHERS)
DROP ROD SUSPENSION (SUPPLIED BY OTHERS)
900
M10
DROP
ROD
CEN
TRES
-
760
M6 D
ROP
ROD
CENT
RES
-1200M6/M10 DROP ROD AND WIRE SUSPENSION CENTRES -
1090
WIR
E SU
SPEN
SION
CEN
TRES
-
250mm
TYP. HEIGHT (EXCLUDING SUSPENSION FIXINGS)
NOTE ORIENTATION OF CIRCULATION LIGHT - SHOULD BE FACING AWAY FROM BED
CarelineWhitecroft Lighting Limited
3 Install diffusers
To fit, insert both outer edges of
the corner diffuser first.
To remove, reverse the sequence
- lift the diffuser to the outer edges
and remove from the inner edge.
Corners
Fit reading light cover below the
opal diffusers.
Opal sheet
Straight sections and
reading light covers
READING LIGHTS (BED HEAD)EMERGENCY LIGHT
CIRCULATION / NIGHTLIGHT
MARSHALLING BOX
OPAL DIFFUSERS
READING LIGHT COVER
INTERNAL FITTING DRIVER BOX
LINEAR END OF BED LIGHT
CarelineWhitecroft Lighting Limited
4 Control Panels, Switches and Supply
DO NOT POWER UP MARSHALLING BOX UNTIL
ALL DEVICES ARE CONNECTED.
TECHNICAL SUPPORT
Telephone: 0161 331 5700
E-mail: [email protected]
http://www.whitecroftlighting.com/
MAINS AND DALI FEED TO MARSHALLING BOX(SUPPLIED BY OTHERS)
STANDARD LAYOUT WITH SCENE CONTROL PANEL (IGNORE COLOUR CHANGE PANEL IF PRODUCT IS NOT TUNEABLE WHITE).
OPTIONS FOR USING THE COMDSIU TO CONNECT A SWITCH FOR BEDSIDE CONTROL OF READING LIGHTS (ON/OFF/DIM UP/DIM DOWN)
PLEASE NOTE: THERE MAY
BE MORE LED DEVICES
CONNECTED THAN SHOWN
HERE. TWO 6-POLE
CONNECTORS SHOULD BE
FREE CLOSEST TO SCREW
TERMINALS FOR CONTROL
PANEL AND SWITCH
CONNECTION (VIA COMDSIU)
INTERNAL FITTING CONNECTIONS (UP TO 6X)
DO NOT REMOVE OR SWAP