enigma cables

ENIGMA Professional Automotive Equipment

USER MANUAL Cables Descriptions

Revision 0.27

ENIGMA Professional Automotive Equipment www.enigmatool.com

ENIGMA User Manual - cable descriptions 2

Table of contents:

Table of contents: ............................................................................................................... 2 Manual revisions .................................................................................................................. 3 Cables and adapter list...................................................................................................... 4 C1 Universal cable for OBD2 plug................................................................................. 6 C10 Universal cable for Motorola HC908..............Błąd! Nie zdefiniowano zakładki. C11 Universal cable for Motorola HC05/11 ............................................................... 8 C12 Universal cable for Motorola HC908/HC912/HC9S12 ................................ 15 C13 Universal cable for NEC 78K MCUs.................................................................... 18

Figure1. Connection diagram for uPD780724, uPD780826, uPD7807828......................... 18 Figure2. Connection diagram for uPD780949. .................................................................... 19 Figure3. Connection diagram for uPD780973, uPD780974 ................................................ 20

C18 BMW EWS III ............................................................................................................. 21 Figure1. EWS III – plug pinout............................................................................................ 21

C21 CITROEN SAXO DASH DIAG ................................................................................ 22 C22 CITROEN BERLINGO HC908 DIAG..................................................................... 23 C23 PEUGEOT 206 DASH DIAG ................................................................................... 24 C24 PEUGEOT 306 DASH DIAG ................................................................................... 25 C26 RENAULT LANGUNA II HC908 DIAG ................................................................. 26 C28 RENAULT CLIO HC908 DIAG ................................................................................ 27 C31 MB VITO MAGNETI MARELI DIAG ...................................................................... 28 C32 SPRINTER VDO DIAG .............................................................................................. 29 C33 SPRINTER TACHO VDO DIAG .............................................................................. 30

Figure1. TACHO KIENZLE – plug pinout ......................................................................... 30 C36 FORD FOCUS DIAG .................................................................................................. 31 C40 BMW CAS/CAS2 DIAG ............................................................................................ 32 A0 POWER ADAPTER TO THE LIGHTER SOCKET ................................................. 33 A1 NEC 78K MICRO ADAPTER ...................................................................................... 34 A3 BMW CAS ADAPTER ................................................................................................... 35 A4 BMW BLUE/BROWN/GREEN CODER ADAPTER ............................................... 36



Disclaimer Specifications written in this document are believed to be accurate, but are not guaranteed to be entirely free of error. The information in this manual is subject to change for functional or performance improvements without notice. Please make sure your manual is the latest edition. While the information herein is assumed to be accurate, SYS MICRO (the manufacturer) assumes no responsibility for any errors or omissions. The manufacturer makes and you receive no warranties or conditions, express, implied, statutory or in any communication with you. The manufacturer specifically disclaims any implied warranty of merchantability or fitness for a particular purpose.

Manual revisions If any error occurs, please inform us and we will try to assist you as soon as possible. For further information on topics or routines not yet specified, please contact us. Manual version

Date Changes

0.1 2006-03-09 First version

0.2 2006-04-11 Added manual versions Added connection for CITROEN BERLINGO HC908 DIAG Added connection for RENAULT CLIO HC908 DIAG Added connection for RENAULT LAGUNA HC908 DIAG Fixed diagram for universal HC908 cable First page changed

0.21 2006-05-16 Added webpage address Fixed diagram for universal HC908 cable

0.22 2006-07-02 Added cable list Added A1 NEC Adapter photo Added C8 cable, ST62xx micro Added C11 cable, 68HC(7)11 micro Added C18 cable, connection to EWS-III Added C21 cable, Citroen Saxo and Peugeot 106 Added C22 cable, Citroen Berlingo and Peugeot Partner to 2002 Added C23 cable, Peugeot 206 to 09/2001 Changed cables names – new cables numeration

0.23 2006-07-27 Added C24 cable, Peugeot 306 Added C36 cable, Ford Focus

0.24 2006-09-21 Added C1 cable (OBD2)

0.25 2006-10-11 Changed cable C11 (for hc11 mcu) C8 – updated

0.26 2006-18-07 Added A0 photo Added A4 photo Added C32 cable (MB SPRINTER VDO diag) Added C33 cable (MB SPRINTER KIENZLE diag) Added C40 cable (CAS Diag by dash plug) Changed cable C36 for FORD FOCUS HC11

0.28 2007-02-24 Added connection diagrams for HC(7)05B6, HC(7)05B16 in PLCC52 and QFP64 package mcu



Cables and adapter list

Number: Description: C0 USB - Connection to the PC Computer – PC Link C1 OBD2 Standard Diagnostic Plug C2 BMW 20 Pin Round Diagnostic Plug C3 Mercedes Benz 38 Pin Round Diagnostic Plug C4 Clips for the 8 Pin SOIC Eeproms (Small) C5 Clips for the 8 Pin DIP Eeproms (Big) C6 Clips for the 14 Pin SOIC Eeproms C7 PINOUT Eeprom Cable - To Solder on boards C8 Cable for ST62xx Micro C9

C10 C11 Cable for HC05 & HC11 Micros C12 Cable for HC08 & HC12 Micro C13 Cable for NEC Micro (Use Always With A1 NEC Adapter) C14 GOLF3 Motometer (And Similar) & Mercedes C-Class 93-95 Motometer DashDIAG C15 C16 BMW E36 compact/Z3 to SW8 DashDIAG C17 C18 BMW EWS3 Module Module DIAG C19 Audi A6 1994-1997 (OBD1) Diagnostic Socket C20 Citroen Jumpy & Peugeot Expert & Fiat Scudo C21 Citroen Saxo & Peugeot 106 DashDIAG C22 Citroen Berlingo & Peugeot Partner Dashboard -2002 DashDIAG C23 Peugeot 206 -09/2001 DashDIAG C24 Peugeot 306 DashDIAG C25 Peugeot 406 & 607 VDO -2003 DashDIAG C26 Renault Laguna II HC08 DashDIAG C27 Renault Laguna II HC12 DashDIAG C28 Renault Clio/Kangoo/Megane Jaeger HC08 C29 Jeep Grand Cherokee 1999/2002 C30 Mercedes E(W211)/CLS(W219)/CLK(W209) 2002- DashDIAG C31 Mercedes Vito Magneti Marelli DashDIAG C32 Mercedes Sprinter VDO DashDIAG C33 Mercedes Sprinter Tachograph Kienzle DashDIAG C34 C35 C36 Ford Focus -2002 DashDIAG C37 Ford Courier/Escort/Fiesta -2003 DashDIAG C38 SsangYong Rexton Micro DashDIAG C39 C40 BMW 1/3/5/6 CAS2/CAS3/CAS3+ & BMW 7 Series 2005- DashDIAG C41 C42 Renault Twingo ST C43 VW Fox & Ford 2005- & Cars With 912 PinOUT DashDIAG C44 VAG 2007- C45 Secured 912/9s12 - Cars & Modules C46 Audi A5 & Audi A4 2007- DashDIAG



ADAPTERS

A0 Power adapter to the lighter socket A1 NEC micro A2 RFID antenna A3 BMW CAS adapter A4 BMW E32 & BMW E34 Blue/Brown/Green Adapter A5 VAG -2007 Adapter A6 912 & 9s12 Adapter A7 American Cars Adapter



C1 Universal cable for OBD2 Plug Cable name: C1 – OBD2 Application: Universal cable for vehicles with OBD2 connector Connection diagram:



C8 Universal cable ST62 micro Cable name: C08 Application: Universal cable to ST62 based devices - FIAT BRAVO/BRAVA/MAREA ST - RENAULT LAGUNA JAEGER ST - RENAULT TWINGO BORG/VDO Connection diagram:

PIN FUNCTION

ENIGMA DB25 COLOR PLAC 68 QFP 52 QFP 80

VSS (GND) 3 BLACK 28 13 VCC (5V) 20 RED 26 12 IO 4 GREEN 17 8 14 IO 5 YELLOW 18 9 15 IO 6 BROWN 32 16 27 IO 7 BLUE 30 14 25 IO (*1) 20 WHITE 21 11 18

Remarks: (*1) This pin is usually directly connected to gnd. In typical case this pin must be disconnected from the board.



C11 Universal cable for Motorola HC05/HC11 Cable name: C11 Application: Universal cable to HC(7)11 MCU based devices Connection schematic to HC11:

ENIGMA DB25

SYSTEM CONN

C11 PLUG

WIRES COLORS

TARGET 68HC(7)11 MOTOROLA

MCU

TXD 1 YELLOW RXD

RXD 14 GREEN TXD

10K

5V OUT 20

GND 3 BLACK VSS

RESET 7 BLUE _RESET

12V OUT 25 RED TARGET 12V

Logic level on this pin must be „LOW” (GND) MOD A(*1)

Logic level on this pin must be „LOW” (GND) BROWN _

MOD B(*2)

Remarks: (*1) This pin is usually connected to GND so usually there is no need to connect. (*2) This pin is usually connected to VCC. Check if this is not directly short to VCC. If yes disconnect this pin from the circuit. After successful read/write operation (after finish work with mcu) this pin must be back soldered to the board.



HC(7)11 PIN ASSIGMENT FOR DIFFERENT PACKAGES MCU TYPE PACKAGE VDD

(5V) VSS

(GND) RXD TXD RESET MOD B

HC11 E SERIES PLCC 52 26 1 20 21 17 2 HC711EA9 PLCC 52 26 22 20 21 17 23 HC11 E SERIES QFP 64 55 23 47 50 43 25 HC11 E SERIES TQFP 52 45 20 39 40 36 21 HC11 E SERIES SDIP 52 27 1 20 22 17 2 HC811E2 DIP 48 48 23 42 43 39 24 HC711KG2, KG4 QFP 100 63 62 71 72 68 69 HC11K4 PLCC 84 64 63 72 73 69 70 HC11K4 QFP 80 71 70 78 79 75 76 HC11K4 PLCC 68 68 67 61 62 58 59 HC11KS LQFP 80 10 8 1 2 76 77



Figure1. Connection diagram for Motorola 68HC05B6/ 68HC05B16 in PLCC52 package. Remarks:

To pin marked on diagram as “1” must be logic level 1 (voltage near 5V). If logic level is other the simplest way is to connect to VDD pin Motorola. If pin is directly connectet do ground (VSS pin) it must be cutted from board or pin must be lifted up. To pin marked on diagram as “0” must be logic level 0 (voltage below 0.8V). If logic level is other the simplest way is to connect to GND pin Motorola. If pin is directly connectet do VDD pin it must be cutted from board or pin must be lifted up.

On pin marked on diagram as IRQ (white cable) voltage must be about 10-12V. If on this pin is lover than 9V pin must be cutted from board or pin must be lifted up.



There are two possibility to power up processor. One to solder purple wire (5V out from ENIGMA) to VDD pin. It is straight power up mcu. Better is to connect RED wire to target board with MCU 12V input voltage supply.

Figure2. Connection diagram for Motorola 68HC05B6/ 68HC05B16 in QFP64 package.

Remarks:

To pin marked on diagram as “1” must be logic level 1 (voltage near 5V). If logic level is other the simplest way is to connect to VDD pin Motorola. If pin is directly connectet do ground (VSS pin) it must be cutted from board or pin must be lifted up. To pin marked on diagram as “0” must be logic level 0 (voltage below 0.8V). If logic level is other the simplest way is to connect to GND pin Motorola. If pin is directly connectet do VDD pin it must be cutted from board or pin must be lifted up.



On pin marked on diagram as IRQ (white cable) voltage must be about 10-12V. If on this pin is lover than 9V pin must be cutted from board or pin must be lifted up. There are two possibility to power up processor. One to solder purple wire (5V out from ENIGMA) to VDD pin. It is straight power up mcu. Better is to connect RED wire to target board with MCU 12V input voltage supply.

Figure3. Connection diagram for Motorola 68HC705B6/ 68HC705B16 in PLCC52 package.

Remarks:

To pin marked on diagram as “1” must be logic level 1 (voltage near 5V). If logic level is other the simplest way is to connect to VDD pin Motorola. If pin is directly connectet do ground (VSS pin) it must be cutted from board or pin must be lifted up.



To pin marked on diagram as “0” must be logic level 0 (voltage below 0.8V). If logic level is other the simplest way is to connect to GND pin Motorola. If pin is directly connectet do VDD pin it must be cutted from board or pin must be lifted up.

On pin marked on diagram as IRQ (white cable) voltage must be about 10-12V. If on this pin is lover than 9V pin must be cutted from board or pin must be lifted up. There are two possibility to power up processor. One to solder purple wire (5V out from ENIGMA) to VDD pin. It is straight power up mcu. Better is to connect RED wire to target board with MCU 12V input voltage supply.

Figure4. Connection diagram for Motorola 68HC705B6/ 68HC705B16 in PLCC52

package. Remarks:

To pin marked on diagram as “1” must be logic level 1 (voltage near 5V). If logic level is other the simplest way is to connect to VDD pin Motorola. If pin is directly



connectet do ground (VSS pin) it must be cutted from board or pin must be lifted up. To pin marked on diagram as “0” must be logic level 0 (voltage below 0.8V). If logic level is other the simplest way is to connect to GND pin Motorola. If pin is directly connectet do VDD pin it must be cutted from board or pin must be lifted up.

On pin marked on diagram as IRQ (white cable) voltage must be about 10-12V. If on this pin is lover than 9V pin must be cutted from board or pin must be lifted up. There are two possibility to power up processor. One to solder purple wire (5V out from ENIGMA) to VDD pin. It is straight power up mcu. Better is two connect RED wire to target board with MCU 12V input voltage supply.



C12 Universal cable for Motorola HC908/HC912/HC9S12 Cable name: C12 Application: Universal cable to HC908/HC9(S)12 MCU based devices Connection schematic:

ENIGMA DB25

SYSTEM CONN

HC912 PLUG

WIRES COLORS

TARGET 68HC9(S)12 MOTOROLA

MCU

RXD + TXD 1+14 GREEN BKGD PIN

1K

5V OUT 20

GND 3 BLACK VSS

RESET 7 BLUE _RESET PIN

12V OUT 25 RED TARGET 12V

Remarks:

HC908 PIN ASSIGMENT FOR DIFFRENT PACKAGES

PIN FUNCTION QFP64 PLCC52 QFP100 VSS (GND) 21 25 30 VCC (5V) 22 26 31 PTA0 26 27 44 RESET 3 10 3 VPP 2 9 2 PTC0 60 4 96 PTC1 61 5 97 OSC1 59 95 3



HC9(S)12 PIN ASSIGMENT FOR DIFFERENT PACKAGES MCU TYPE PACKAGE VDD

(5V) VSS

(GND) BKGD RESET EXTAL XTAL

912 B32 QFP 80 31 30 17 32 33 34 912 D60, DG128 QFP 112 42 40 23 46 47 48 912 D60A QFP 80 30 20 15 34 35 36 9S12 Dx64, Dx128, Dx256

QFP 80 29 28 15 30 34 35

9S12 Dx64, Dx128, Dx256

QFP 112 41 40 23 42 46 47

9S12 H QFP 112 37 38 39 40 44 45 9S12 H LQFP 144 51 52 53 54 58 59



C13 Universal cable for NEC 78K MCUs Cable name: C13 Application: Universal cable to NEC78K0 MCU based devices Required additional equipment: NEC ADAPTER for ENIGMA

Figure1. Connection diagram for uPD780724, uPD780826, uPD7807828.



Figure2. Connection diagram for uPD780949.



Figure3. Connection diagram for uPD780973, uPD780974



C18 BMW EWS III Cable name: C18 Application: BMW, MINI, ROVER with EWS III module Connection schematic:

Figure1. EWS III – plug pinout



C21 CITROEN SAXO DASH DIAG Cable name: C21 Application: CITROEN SAXO, PEUGEOT 106 VDO DIAG Connection schematic:



C22 CITROEN BERLINGO HC908 DIAG Cable name: C22 Application: CITROEN BERLINGO, PEUGEOT PARTNER JAEGER HC908 Connection schematic:



C23 PEUGEOT 206 DASH DIAG Cable name: C23 Application: PEUGEOT 206 JAEGER TO 09/2001 Connection schematic:



C24 PEUGEOT 306 DASH DIAG Cable name: C24 Application: PEUGEOT 306 VDO DIAG Connection schematic:



C26 RENAULT LANGUNA II HC908 DIAG Cable name: C26 Application: RENAULT LAGUNA II JAEGER HC908 (without computer) Connection schematic:



C28 RENAULT CLIO HC908 DIAG Cable name: C28 Application: RENAULT CLIO/KANGOO/MEGANE JAEGER HC908 Connection schematic:



C31 MB VITO MAGNETI MARELI DIAG Cable name: C31 Application: MERCEDES VITO/VIANO MAGNETI MARELLI DASH DIAG Connection schematic:



C32 SPRINTER VDO DIAG Cable name: C32 Application: MERCEDES SPRINTER/VITO ..2000 VDO DASH DIAG Connection schematic:



C33 SPRINTER TACHO VDO DIAG Cable name: C33 Application: MERCEDES SPRINTER TACHO VDO DASH DIAG Connection schematic:

Figure1. TACHO KIENZLE – plug pinout



C36 FORD FOCUS DIAG Cable name: C36 Application: FORD FOCUS HC11 Connection schematic:



C40 BMW CAS/CAS2 DIAG Cable name: C40 Application: NEW BMW 1/3/5/6 CAS DIAG BY DASH PLUG Connection schematic:



A0 POWER ADAPTER TO THE LIGHTER SOCKET



A1 NEC 78K MICRO ADAPTER Adapter name: A3 Application: All bsi/dashboards/other devices with 78K0 mcu e.g. - ALFA 147 - CITROEN BERLINGO/XSARA BSI/DASH - FORD FIESTA/KA - HYUNDAI ACCENT/TERRACAN/ - OPEL AGILA/CORSA - RENAULT CLIO/KANGOO/MEGANE SAGEM - RENAULT MASTER - ….



A3 BMW CAS ADAPTER Adapter name: A3 Application: All New BMW Models – E60/E61/E64/E65/E66/E81/E93 etc. This adapter connect standard OBD2 cable with DB15 plug to ENIGMA SYS CONN DB25 socket. Connection schematic:

ENIGMA DB25

SYSTEM CONN

BMW FAST OBD2

ADAPTER

OBD2 16 PIN PLUG

(IN CAR)

DB25 DB15 KLINE 23 23 6 7 KLINE

GND 3 3 4 4+5 GND

+12V INPUT 13 13 15 16 +12V BATTERY



A4 BMW BLUE/BROWN/GREEN CODER ADAPTER

enigma cables

Documents

professional

motorola 68hc05b6

motorola 68hc705b6

enigma user

solder purple

gnd reset

connect red

c11 universal