energi savr node qs - lutron electronics, inc. - dimmers … dali 369243c.pdf · 2012-10-31 ·...

® Specif icat ion Submittal page

Job Name:

Job Number:

Model Numbers:

Energi Savr NodeTM QS QSNE-2DAL-D DALI Fixture Controller

369-243c 1 05.19.10

Energi Savr Node QSThe Energi Savr Node QS unit is a DIN-rail mounted controller for DALI-compliant Digital Addressable loads. It provides DALI bus power and control for two independent DALI Buses with up to 64 ballasts each. The Energi Savr Node QS unit also provides direct connections and power for the following Lutron® devices:

•Occupancysensors•Daylightsensors•IR receivers•QS devices

Features•ProvidespowerforeitheroneortwobusesofDALI

compliant digital addressable loads (up to 250 mA per bus).

•EachDALIBuscancontrolamaximumof16zones.•Powerfailurememoryretainscontrolunitprogram-

ming in the event of a power loss.•Defaultconfigurationrequiresnocommissioning.•ProgrammingavailableviatheEnergi Savr Node QS

hand-held device.•Fouroccupancysensorinputsforautomatedcontrol

of lights in areas.

•Fourdaylightsensorinputsautomaticallyadjustlightlevels based on the amount of natural light entering through the windows.

•FourIRreceiverinputsforpersonalcontrol.•Addmoreoccupancysensors,daylightsensors,orIRreceiversbyconnectingQSSensorModules(QSMs).

•IncludesQScontrollinkforseamlessintegrationoflights,motorizedwindowtreatments,controlsta-tions,andQSSensorModules.

•Energi Savr Node QS units andQSSensorModulescan be used in a Quantum®systemtocontrolandmanage light in an entire building.

500-13431 Rev. B

N1771Z096

Energi Savr Node QS

Ballast

seeTouch® QS Wallstation

Ballast

Ballast

Ballast

Quantum Panel

LUTRON

LUTR

ON

R

QS Contact Closure Interface

GRAFIK Eye QSEnergi Savr

Node QS

LUTRON

LUTR

ON

R

Up to 64 ballasts on each loop

QS Control Link

DALIBus1

DALI Bus 2Ballast

Ballast

Energi Savr Node QS

Energi Savr Node QS

Quantum Panel

GRAFIKEyeQS

QS Contact Closure Interface


Ballast

Ballast

IR Receiver

DaylightSensor

OccupancySensor

220-240 V~ Upto100total QS devicesEthernet

ProgrammingLink

Onesensorgroupshown; connections

available for up to four sensor groups.

Wireless Communication QSM

RadioPowrSavrTM OccupancySensor(upto10perQSM)

Radio Powr Savr DaylightSensor (upto10perQSM)

PicoTM Wireless Controller (up to10perQSM)

Wired Daylight

Sensors*Wired Occupancy Sensors*

Wired IR Receivers*

*Upto4wiredsensorstotal(ofanytype)

Note:MultipleQSMscanbeadded to increase the number of wireless sensors and Pico wireless controllers.


Job Name:

Job Number:

Model Numbers:


369-243c 2 05.19.10

Typical Application: Requires commissioning

OccupancyS

ensorD

aylightS

ensor

Loop 2Loop 1

Versaplex Q

S

LUTRON

Wired to

sensor group 4

Open Offices Corridor Private Offices

OccupancySensor

QS Link

OccupancySensor

OccupancySensor

Energi Savr Node QS

Energi Savr Node QS

DaylightSensor

DALILoop

DALILoop

DALILoop


Win

dow

Win

dow

Win

dow

LUTRON OccupancySensor Daylight

Sensor

LUTRON

OccupancySensor Daylight

Sensor

LUTRON

OccupancySensor Daylight

Sensor

LUTRON


OccupancySensor

DaylightSensor

LUTRON

DALILoop

DALILoop

DALILoop

QS

Lin

k

QS Link

OpenOffices Corridor PrivateOffices



QSLink

QSLink

QSLink

Win

dow

Win

dow

Win

dow

DALI Bus

Daylight Sensor

Daylight Sensor

Daylight Sensor

Daylight Sensor

Daylight Sensor

Occupancy Sensor

Energi Savr Node QS

Energi Savr Node QS

Occupancy Sensor

Occupancy Sensor

Occupancy Sensor

Occupancy Sensor

Occupancy Sensor

Occupancy Sensor

DALI Bus

DALI Bus

DALI Bus

DALI Bus

DALI Bus


Job Name:

Job Number:

Model Numbers:


369-243c 3 05.19.10

OccupancySensor

OccupancySensor

Loop 2

Wired to sensor group 2

Loop 1

Perimeter Interior

Win

dow

Win

dow

Energi Savr Node QS


OccupancySensor

DaylightSensor

Loop 2Loop 1

Perimeter Interior

Win

dow

Win

dow

Energi Savr Node QS

LUTRON


preconfigured mode 2two Zones with occupancy Sensors* Six fixtures shown on each bus, however,

up to 64 fixtures can be connected per bus.

preconfigured mode 1perimeter Daylighting* four fixtures shown on bus 1 and eight

fixtures shown on bus 2, however, up to 64 fixtures can be connected per bus.

Occupancy Sensor Daylight SensorConnectedtosensorgroup1 ControlsBus1only ControlsBus1onlyConnected to sensor group 2 ControlsBus2only ControlsBus2onlyConnected to sensor group 3 Controls both Buses ControlsbothBuseswithequaldaylightgainConnected to sensor group 4 Controls both Buses ControlsbothBuseswithlowerdaylightgainonLoop2

Default behavior for Sensor connections

Simple Applications: Preconfigured modes require no commissioning

Troubleshooting and Maintenance Features•Maintainsredundantmemoryofballastprogrammingforeaseofsingleormultiple

ballast replacement.•Afterinstallation,"TEST"buttonverifiesDALIwiringonallfixtures•StatusLEDsverifyconnectionstocontrolstationsandsensors.•Afterinstallation,Energi Savr Node QSunitidentifiesballastcommunicationfail-

ures.

Perimeter PerimeterInterior Interior

Win

dow

Win

dow

Win

dow

Win

dow

Daylight Sensor




Energi Savr

Node QS

Energi Savr

Node QS

Occupancy Sensor

Occupancy Sensor

Occupancy Sensor

Bus1 Bus1Bus 2

Bus 2


Job Name:

Job Number:

Model Numbers:


369-243c 4 05.19.10

Specifications

Energi Savr Node QS

Power

•220-240V 50/60Hz,maxcurrentdraw100mA•LightningstrikeprotectionmeetsANSI/IEEEstandard62.31-1980.Canwithstandvoltagesurgesofupto 6 000 V and current surges of up to 3 000 A.

•DALIBusOutput:18V 250mAmaximumperbus.

Standards

•IEC60669-2-1•Lutron®QualitySystemsregisteredtoISO9001.2000

Environment

•AmbientTemperatureOperatingRange:0ºCto40ºC•Relativehumidity:lessthan90%non-condensing•Forindooruseonly

Terminals

•Mainswiring:1,0mm2to4,0mm2(18AWGto12AWG)•DALIBusWiring:1,0mm2to4,0mm2(18AWGto12AWG)•SensorWiring:1,0mm2to2,5mm2 (18AWGto14AWG)

Mounting

•MountstostandardDINrail•Width=9modules(161,7mm)

DALI Buses

•Upto64DALIcompliantloadsoneachbuscanbead-dressedandgroupedinto16zones

•Energi Savr Node QS unit supplies 250 mA to power each bus.

•DALIBuswiresarepolarityinsensitiveandtopology-free.

QS Link Limits

•TheQSlinkcanhaveupto100devicesand100zones.•EachEnergi Savr Node QS unit counts as one device towardthe100devicelimit.

•Eachassignedzonecountstowardthe100zonelimit.•SeeTable1(page6)fordevicedetails.

Occupancy Sensors Connected to the Energi Savr Node QS unit

•Useoccupancysensorstoautomaticallyturnthelightsoffinanareaafixedtimeafteritbecomesvacant.

•Useoccupancysensorstoautomaticallyturnthelights on in area when it becomes occupied and toautomaticallyturnthelightsoffinanareaafixedtimeafteritbecomesvacant.

•Fouroccupancysensorscanconnectdirectlytothe Energi Savr Node QS unit.

•Eacharea'soccupiedlevelandunoccupiedlevelcan be programmed.

•PowerSupplyOutputs(4) - 20-24 V 50mAmaximum. -Anauxiliarypowersupplymustbeusedifthe

devicerequiresmorethan50mA.•Occupancysensormustprovideadrycontact

closure or solid-state output.

Daylight Sensors Connected to the Energi Savr Node QS unit

•Lutrondaylightsensorsallowdaylightharvestingwith programmable gain settings in up to four gain groups per area.

•FourdaylightsensorscanconnectdirectlytotheEnergi Savr Node QS unit.

Infrared Receivers Connected to the Energi Savr Node QS unit

•UseLutron IR receivers for personal control of individuallightingzones.

•FourIRreceiverscanconnectdirectlytothe Energi Savr Node QS unit.


Job Name:

Job Number:

Model Numbers:


369-243c 5 05.19.10

Specifications (continued)

QSM (QS Sensor Module) - Integrating Wired and Wireless Sensors

•UsetheQSMtointegrateRadioPowrSavrTMOccupancy/Vacancysensors,Radio Powr Savr Daylightsensors,andPicoTMWirelessControllerstocontrolzonesontheEnergi Savr Node QS unit.

•Assignupto10Radio Powr SavrOccupancy/Vacancysensors per Energi Savr NodeQSunitviaQSM.

•Assignupto10Radio Powr SavrDaylightsensorsperEnergi Savr Node QSunitviaQSM.

•Assignupto10Pico Wireless Controllers per Energi Savr Node QS unit viaQSM.

•AddadditionalwiredandwirelesssensorsbyaddingQSSensorModulestotheQSlink.

• Wireandpowerupto4wiredsensors(ofanytype)total —Daylightsensors —Occupancysensors — Infrared (IR) sensors

•TheRadio Powr Savr sensors and Pico Wireless Control-lersassociatedwiththeQSMshouldbemountedwithin60ft(18m)lineofsight,or30ft(9m)throughwalls,oftheQSM.

•RefertoQSMSpecificationSubmittalformoreinforma-tion.

Accessory Controls•seeTouch®QSwallstationscanbeconfiguredto

control Energi Savr Node QSunitzones.•Selectoneof16scenesandoffinEnergi Savr Node QS

unit areas.•ControlindividuallightingzonesinEnergi Savr Node QS

unit areas.•EachEnergi Savr Node QS unit can power up to three

seeTouch QS controls.•LEDindicatordisplaysthestatusofprogrammedlights.

Communication with GRAFIK Eye® QS•Energi Savr Node QSunitzonesrespondto

GRAFIK Eye QS scene buttons in areas associ-ated with the GRAFIK Eye QS.

•Energi Savr Node QSunitzonesrespondtoscenecommandsinitiatedbytheGRAFIK Eye QSastronomictimeclockinareasassociatedwith the GRAFIK Eye QS.

•Energi Savr Node QS unit operates in afterhours mode in areas associated with a GRAFIK Eye QS that is in afterhours mode.

Communication with QSE-IO•Energi Savr Node QSunitzonesrespondtoscenecommandsinitiatedbytheQSE-IOinsceneselectionmodeoroccupancysensormode.


Job Name:

Job Number:

Model Numbers:


369-243c 6 05.19.10

QS System LimitsThetablebelowliststhedevicesavailableontheQSlink.Seebelowforeachdevice’scounttowardthelinkmaximumsforzonesanddevices.

AQSlinkcanhaveupto100zones(outputs)and100devices.Energi Savr NodeQSunitcansupply3power draw units.

Table 1: QS System Limits

QS Device Description

Zone Count

Device Count

Power Draw Units (supplied)

Power Draw Units (consumed)

Energi Savr Node QS DALI QSNE-2DAL-D up to 32 1 3 0

QSSensorModule 0 1 0 3

Lutron®OccupancySensor(connectedtoQSSensorModule)* 0 0 0 2

LutronDaylightSensor(connectedtoQSSensorModule)* 0 0 0 0.5

Lutron Infrared(IR)Receiver(connectedtoQSSensorModule)* 0 0 0 0.5

3-zoneGRAFIKEye® QS 3 1 3 0

4-zoneGRAFIK Eye QS 4 1 3 0

6-zoneGRAFIK Eye QS 6 1 3 0

6-zoneGRAFIK Eye QS with DALI 6 1 3 0



seeTouch® QS 0 1 0 1

QS contact closure interface up to 5 1 0 3

QSnetworkinterfaceforaudio-visualintegration 0 1 0 2

QSlinkpowersupply 0 0 8 0

*Note:PowerdrawunitsareconsumedbyOccupancySensors,DaylightSensors,andIRReceiversonlyifconnectedtotheQSSensorModule(QSM).PowerdrawcalculationsarenotneededforwirelesssensorsorsensorsconnecteddirectlytotheEnergi Savr Node QS units.


Job Name:

Job Number:

Model Numbers:


369-243c 7 05.19.10

Mechanical Dimensions

500-13431 Rev. B

N1771Z096

161.6mm(6.36 in)

60.6 mm (2.39in)

500-13431 Rev. B

N1771Z096

89.7mm(3.53 in)


Job Name:

Job Number:

Model Numbers:


369-243c 8 05.19.10

Overview of Wiring Terminals

500-13431 Rev. B

N1771Z096

mains Wiring

Dali bus 1*

Dali bus 2*QS

linkSensorsprogramming

port

* Wire Dali according to local codes.

PELV


Job Name:

Job Number:

Model Numbers:


369-243c 9 05.19.10

Wiring: Line Voltage

Wiring from Distribution to Bus Supply

•Turnoffbreakeratdistributionpanel.

•Runline,neutral,andgroundwiresfroma 220-240V~50/60HzfeedtotheEnergi Savr Node QS unit.

Emergency Lighting Applications

•Usenormal(non-essential)poweronly.

•Whennormalpowerdropsout,theEnergi Savr Node QS unit will not power the DALI Buses. When thisoccurs,ballastspoweredfromemergencyfeedsgototheiremergencymode,fulllightoutputbydefault.

Mains Wiring and Low Voltage Separation

•TheEnergi Savr Node QS unit is designed to sepa-ratemainswiringfromPELVcircuits.

•Followappropriatelocalandnationalcodestoavoidviolatingrequiredseparationguidelines.

500-13431 Rev. B

N1771Z096

500-13431 Rev. B

N1771Z096

n

l

Distribution panel


Job Name:

Job Number:

Model Numbers:


369-243c 10 05.19.10

500-13431 Rev. B

N1771Z096

500-13431 Rev. B

N1771Z096

Wiring: DALI Bus

The Energi Savr Node QSunitwillsupplypowertoanindependentDALIBus,whichsupportsamaxi-mum of 64 ballasts.

DALI Wiring

•DALIwiringisnotSELV.

•DALIwiringistreatedasmainsvoltage,andthusmayberunwithinthesamesheathing.

•Ensurethatthereisnogreaterthana2Vdropbetween the Energi Savr Node QS unit and the end of the DALI Bus.

•Consultallnationalandlocalelectricalcodesforseparationrequirements.

Wire GaugeMaximum DALI-compliant Bus Wire Length

4,0mm2(12AWG) 671m(2200ft)2,5mm2(14AWG) 427m(1400ft)1,5mm2(16AWG) 275m(900ft)1,0mm2(18AWG) 175m(570ft)

DALI1

DALI1

DALI 2

DALI 2

DALI Bus 1

DALI Bus 2


Job Name:

Job Number:

Model Numbers:


369-243c 11 05.19.10

Wiring: QS Control Link

PELV QS System Low-Voltage Wiring

•Systemcommunicatesusinglow-voltagewiring.

•Wiringmaybedaisychainedort-tapped.

•Wiringmustberunseparatefromline/mainsvolt-age.

•Totallengthofcontrollinkmustnotexceed600m.

•Usetwo1,0mm2(18AWG)conductorsforcontrolpower(24V,COM).

•Useone,twisted-shieldedpairof1,0mm2(18AWG)fordatalink(MUX,MUX).

500-13431 Rev. B

N1771Z096

(1)(2)(3)(4)

com24 VmuXmuX

Daisy-Chain Wiring Example

EnergiSavrNode QS unit

Sivoia® QS Shade

QSM Sivoia® QS SmartPower

Panel

seeTouch® QS Wallstations

500-13431 Rev. B

N1771Z096

QSControlLink


Job Name:

Job Number:

Model Numbers:


369-243c 12 05.19.10

Wiring: QS Control Link (continued)T-Tap Wiring Example

Sivoia® QS SmartPower

Panel

Sivoia® QS Shade

seeTouch® QS Wallstations

QSM

Energi Savr Node QS unit

QSControlLink


Job Name:

Job Number:

Model Numbers:


369-243c 13 05.19.10

4 3

2 1 C B A

4 3

2 1 C B A

4 3

2 1 C B A

4 3

2 1 C B A4

3 2

1 C B A

4 3

2 1 C B A

4 3

2 1 C B A

4

3

2

1

4

3

2

1

4

3

2

1

4

3

2

1

4

3

2

1

4

3

2

1

4

3

2

1

ESN1powerswallstation1only;terminal2 terminates at wallsta-tion1

Wiring: QS Control Link (continued)Low-Voltage Wiring Example

ESN = Energi Savr Node QS unit

eSn 3

eSn 1

eSn 2

eSn 4

1 2

3

4

5

6

7

ESN4powerswallstations5,6,and7only;noterminal2connec-tion between wallstations 4 and 5

ESN3powerswallstations2,3,and4only;noterminal2connectionbetween wallstations 4 and 5

ESN2andESN3havetheirownpowersupply;noterminal2con-nection

•Connecttheterminal1,3,and4connectionstoallcontrolinterfaces.•Eachcontrolunithasitsownpowersupply.Terminatetheterminal2

connection (24 V power) so that each control unit supplies power to amaximumofthreewallstations.Donotconnectterminal2betweenan Energi Savr Node QSunitandanyotherEnergi Savr Node QS unitand/oranotherpowersupply.

•Eachwallstationshouldreceivepowerfromonlyoneunit.


Job Name:

Job Number:

Model Numbers:


369-243c 14 05.19.10

500-13431 Rev. B

N1771Z096

Wiring: Class 2 SensorsElectrical Contractors and Engineers

•AllsensorwiringisPELV.Followallapplicablenationaland local codes for proper circuit separation and pro-tection.

•Class2sensorterminalsaccept1.0-2.5mm2 (18-14AWG)solidconductors.

•MainsvoltageandPELVwiringmustbekeptseparate.

Wiring Instructions:•Turnoffbreakeratdistributionpanel.

Daylight Sensor:•Connectthefourconductorstothefourterminalsas

shown.•Terminals: Red=20V Black=Common White=IR Yellow=Daylight•DaylightSensormustbeplacedwithin30mofthe

Energi Savr Node QS unit.

noteS:•Onedaylightsensorcanbewiredtoeachsensor

group.•Consultthedaylightsensorspecificationsheettoproperlylocatethesensor.

•Donotplacethesensorabovependants,fixtures,directlybelowlightingfixtures,orwithinskylightwells.

Occupancy Sensor:•Connectthreeconductorstothreeterminalsas

shown.•Oneoccupancysensorcanbewiredtoeachsensor

group.

IR Receiver:•Connectthethreeconductorstothethreeterminals

as shown.•Receivermustbeplacedwithin30moftheEnergi

Savr Node QS unit.noteS:

•OneIRReceivercanbewiredtoeachsensorgroup. *IfadaylightsensorandIRreceiverareconnected,donotconnectthedaylightsensor'sIRoutput(white wire).

NOTE: There are four sensor groups.Eachgroup wires the same and is shown above.

20 V

IR Receiver

DaylightSensor

OccupancySensor

Common

500-13431 Rev. B

N1771Z096

LUTRON

OccupancySensorDaylight/IRSensor IR Receiver*

Red

Black

Yello

w

Blu

e

Black

Red

Red

Black

Whi

te

Whi

te*

500-13431 Rev. B

N1771Z096

SensorGroup1

Sensor Group 3

Sensor Group 2

Sensor Group 4

LUTRONR


Job Name:

Job Number:

Model Numbers:


369-243c 15 05.19.10

Installation of Programming Connection•TheEnergi Savr Node QS Hand-Held Device is used to program Energi Savr Node QS units in installations re-quiringcommissioning.

•ConnectiontothesystemismadeviaWi-Fithroughawirelessrouterasshownbelow.•Itisrecommendedthatthepersonprogrammingthesystemisabletoseeallofthelightsduringtheprogram-

ming process.

NOTE:EthernetprogrammingconnectionnotusedwhentheEnergi Savr Node QS unit is part of a Quantum®

system.

•IfEnergi Savr Node QSunitisaccessibleandlocatedsuchthatlightsarevisiblefromtheWi-Ficoveragearea,thenthewirelessroutercanbeconnecteddirectlytoEnergi Savr Node QS unit as shown below.

Recommended: Install Wall Jack for Commissioning

Alternate Approach: Router connected directly to the Energi Savr Node QS unit

500-13431 Rev. B

N1771Z096

500-13431 Rev. B

N1771Z096

500-13431 Rev. B

N1771Z096

500-13431 Rev. B

N1771Z096

500-13431 Rev. B

N1771Z096

500-13431 Rev. B

N1771Z096

500-13431 Rev. B

N1771Z096

500-13431 Rev. B

N1771Z096

500-13431 Rev. B

N1771Z096

500-13431 Rev. B

N1771Z096

500-13431 Rev. B

N1771Z096

500-13431 Rev. B

N1771Z096

Wireless Router (byothers)

QSControlLink

Wireless Router (byothers)

QSControlLink



Wireless router- connectedtemporarily(duringsystemcommissioning and futureadjustments)orpermanently.

All lights should be visible fromthe wireless coverage area ofthe router

Wireless router- connectedtemporarily(duringsystemcommissioning and futureadjustments)orpermanently.

All lights should be visible fromthe wireless coverage area ofthe router

DedicatedEthernetconnection* for Energi Savr Node QS units

* Note: Energi Savr Node QSunitsarenotdesignedtoexistonanopennetwork.ConnectiontoanopennetworkcouldresultinreducedperformanceandEthernetconnectivityissues.

* Note: Energi Savr Node QSunitsarenotdesignedtoexistonanopennetwork.ConnectiontoanopennetworkcouldresultinreducedperformanceandEthernetconnectivityissues.

DedicatedEthernetconnection* for Energi Savr Node QS units

EasilyaccessibleEthernetwalljackinstalledintheareacontaining the lights

energi savr node qs - lutron electronics, inc. - dimmers … dali 369243c.pdf · 2012-10-31 ·...

Documents