emtelle fibre optic cables catalogue 2017 · all emtelle manufactured fibre optic cables complies...

Emtelle Fibre Optic Cables Catalogue 2017

EMTELLE FIBRE OPTIC CABLES

2 ENGAGE.LISTEN.INNOVATE.DELIVER.

Table of Contents

About Emtelle ..............................................................................................................3

General Information .....................................................................................................4

Direct Install (DI) Fibre Optic Cable .............................................................................5

Blown Fibre Optic Cable ..............................................................................................6

Direct Buried (DB) Fibre Optic Cable ..........................................................................7

Aerial (ADSS) Fibre Optic Cable .................................................................................8

Low Fire Hazard (LFH) Fibre Optic Cable ...................................................................9

RTRYVA Fibre Optic Cable........................................................................................10

Cable in Duct (CID) ..................................................................................................12

Wind farm Fibre Optic Cables (SCADA)....................................................................13

(SPEN) Approved Cables ..........................................................................................16

(SSE) Cable...............................................................................................................18

(NRTS) Approved Cables ..........................................................................................20

(Vodafone) Cables .....................................................................................................24

Appendix A - Fibre Properties Tables ........................................................................25


3ENGAGE.LISTEN.INNOVATE.DELIVER.

About Emtelle

Introduction

With over 30 years experience in the telecommunications industry, Emtelle is a leading global manufacturer of blown fibre and ducted network solutions. We have a proven track record, and a reputation for exemplary custom-er service.

The history of telecommunications and the nature of our company are intrinsically linked. As we have responded to changes in technology, market demand and customer expectation, our innovation, expansion, and development has in turn helped shape the industry.

We have not only evolved as a direct result of telecommunications. Our innovative and forward thinking approach to solving problems for customers has ensured we are a leading edge proponent of modern telecommunications and a global market leader in multiple sectors.

When it comes to experience, production volume, and innovation, Emtelle is the industry leader in plastic tubing for the telecommunication sector. As the first high-volume producer in the world of blown fibre tubing, Emtelle’s expertise is unrivalled. Over 30 years of history as a supplier has shaped the high quality of our product, as well as helped us to develop the most comprehensive and proactive customer service program possible.

Emtelle Group’s high volume projects include ITS projects in the UK and Australia, high rises in Dubai, ports in the USA, the Gotthard Tunnel in Switzerland, the Olympic stadium in London, and the Kuala Lumpur monorail in Malaysia.

Key Emtelle Sectors

Telecoms We have a long-standing track record in telecoms – we are directly or indirectly present in all impor-tant “Fibre-to-the-X” markets worldwide.

Power is our comprehensive, easy to install, high performance duct systems and accessories for underground power duct requirements.

Rail It is critical that modern rail infrastructures are underpinned by high speed, scalable and flexible communication systems – Emtelle offer key products designed to facilitate these systems.

Water We are the market-leading manufacturer of durable, reliable PE (polyethylene) pipe systems for drinking water supply and sewage systems, as well as irrigation systems for agriculture.

Highway It is critical that modern highway infrastructures are underpinned by high speed, scalable and flexi-ble communication systems. Emtelle has a range of products to facilitate this.

Industrial Emtelle is a leading manufacturer of high quality PVC & HDPE ducts for use in Industrial and Civil applications.



Performance StandardAll Emtelle manufactured Fibre Optic Cables complies with the international standard IEC.60794.

Optical Fibre and Tube IdentificationEmtelle standard fibre and tube colours are to EIA 598 as shown in table below. Customer specific colour configu-rations are available on request.

Number 1 2 3 4 5 6 7 8 9 10 11 12

Colour Blue Orange Green Brown Grey White Red Black Yellow Violet Pink Aqua

Number 11 12 13 14 15 16 17 18 19 20 21 22

Colour Blue** Orange** Green** Brown** Grey** White** Red** Black** Yellow** Violet** Pink** Aqua**

** denotes additional identification e.g. ring markings

Fibre PropertiesRefer to Appendix A for the following fibre properties tables:Single Mode G.652DSingle Mode G.657A1 and A2Multimode 50/125 and 62.5/125

Sheath MarkingEmtelle standard sheath marking is every 1 meter as shown in the example below. Customer specific markings are available on request (separate product code).

Product TestingAt Emtelle the following product testing is carried out on all our Cable products.

Test Method

Max. Installation Tension IEC 60794–1–2-E1

Max. Operation Tension IEC 60794–1–2-E1

Crush IEC 60794–1–2-E3

Impact IEC 60794–1–2-E4

Torsion IEC 60794–1–2-E7

Repeated Bending IEC 60794–1–2-E6

Cable Bend IEC 60794–1–2-E11

Temperature Cycling IEC 60794–1–2-F1

Water Penetration IEC 60794–1–2-F5B

General Information

Emtelle Fibre Optic Cable - Fibre Count - Fibre type - Product Code - Batch ID - Meter Mark



Direct Install (DI) Fibre Optic Cable

Cable ApplicationThis optical fibre cable range is all dielectric and designed for installation into a duct by blowing or pulling.

Cable Fibre Count Options

144f

96f 24f 48f 36f 12f 72f

12 Fibres per tubeFibres coloured as (1) blue; (2) orange; (3) green; (4) brown; (5) grey; (6) white; (7) red; (8) black t; (9) yellow; (10) violet; (11) pink; (12) turquoiseTubes:1stblue; 2nd orange; 3rd green; 4th brown; 5th grey; 6th white, 7th red, 8th, black, 9th yellow, 10th violet, 11th pink, 12th turquoise (fillers

where necessary)

Cable Features and BenefitsSheath: Medium density polyethylene, UV-stableWater Blocking: Gel-filled loose tube, water blocking yarn and tapeStrain Relief FRP central strength memberStripping: Ripcord provided for quick and easy sheath removal Fibre counts: 12f to 144fFibre types Available: Single mode to G.652D, G.657A1, G.657A2 (ITU-T) Multimode 62.5/125 OM1 (ISO 11801) Multimode 50/125 OM2, OM3, OM4 (ISO 11801)

Cable CharacteristicsMax fibres - 12f 24f 36f 48f 72f 96f 144f

Number of tubes - 6 6 6 6 6 8 12Tube OD/ID Ø mm 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6

Number of dummy tubes # 5 4 3 2 - - -Central strength member Ø mm 2.3 2.3 2.3 2.3 2.3 2.6/3.7 3/6.9

Cable mass kg/km 86 87 87 88 90 114 178Sheath Thickness mm 2 2 2 2 2 2 2

Cable outer Ø mm 10.9 10.9 10.9 10.9 10.9 12.4 15.5Bending radius (Installation) mm 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x Ø

Bending radius (Service) mm 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x ØMax load (fibre strain 0.3% max)* kN 1.5 1.5 1.5 1.5 1.5 2.0 3.0

Design Spec - CP2596 CP2596 CP2596 CP2596 CP2596 CP2596 CP2596Supply length Km 4 & 6 4 & 6 4 & 6 4 & 6 4 & 6 4 & 6 4 & 6

Product Code (G.652D version) - 90565 90566 90567 90568 90569 90570 90571

*Different tensile strengths are available on request.



Blown Fibre Optic Cable

Cable ApplicationThis optical fibre mini-cable range is for insertion into single or multi-duct tube assemblies. It’s designed to be installed in telecommunications networks by the use of viscous drag with the assistance of pushing by a suitable blowing apparatus. This cable range is not designed for installation by pulling.


72f 144f

48f 24f 96f 12f 36f

12 Fibres per tubeFibres coloured as (1) blue; (2) orange; (3) green; (4) brown; (5) grey; (6) white; (7) red; (8) black t; (9) yellow; (10) violet; (11) pink; (12) turquoise

Tubes:1stblue; 2nd orange; 3rd green; 4th brown; 5th grey; 6th white, 7th red, 8th, black, 9th yellow, 10th violet, 11th pink, 12th turquoise (fillers where necessary)

Cable Features and BenefitsSheath: High density polyethyleneWater Blocking: Gel-filled loose tube, dry core with water swellable elementsStrain Relief FRP central strength memberStripping: Ripcord provided for quick and easy sheath removalFibre counts: 12f to 144fFibre types available: Single mode to G.652D, G.657A1, G.657A2 (ITU-T) Multimode 62.5/125 OM1 (ISO 11801) Multimode 50/125 OM2, OM3, OM4 (ISO 11801)



Number of dummy tubes # 5 4 3 2 - - -Central strength member Ø mm 1.65 1.65 1.65 1.65 1.65 2.6 4.5

Cable mass kg/km 24 25 25 26 27 37 58Sheath Thickness mm 0.5 0.5 0.5 0.5 0.5 0.5 0.5



Design Spec - CP1354A CP1354A CP1354A CP1354A CP1354A CP1123C CP1747ASupply length Km 4, 6, 8 & 12 4, 6, 8 & 12 4, 6, 8 & 12 4, 6, 8 & 12 4, 6, 8 & 12 4, 6, 8 & 12 4, 6, 8 & 12





Direct Buried (DB) Fibre Optic Cable

Cable ApplicationThis optical fibre cable range is all dielectric and designed for installation into duct by pulling, directly onto cable trays or direct burial into suitably prepared ground.


96f 72f 48f 12f 36f 24f

144f



Cable Features and BenefitsOuter Sheath: High density polyethylene, UV StableInner sheath: Black nylonWater blocking: Gel-filled loose tube, water blocking yarn and tapeStrain relief: FRP central strength memberStripping: Ripcord provided for quick and easy sheath removalFibre counts: 12f to 144fFibre types available: Single mode to G.652D, G.657A1, G.657A2 (ITU-T) Multimode 62.5/125 OM1 (ISO 11801) Multimode 50/125 OM2, OM3, OM4 (ISO 11801)




Cable mass kg/km 106 107 107 108 110 137 206Sheath Thickness mm 1.6 1.6 1.6 1.6 1.6 1.6 1.6

Cable outer Ø mm 12.5 12.5 12.5 12.5 12.5 13.9 17Bending radius (Installation) mm 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x Ø







Aerial (ADSS) Fibre Optic Cable

Cable ApplicationThis optical fibre cable range is designed for aerial network deployment as an overhead self-supporting cable.


144f

72f 48f 12f 36f 24f 96f



Cable Features and BenefitsSheath: Medium density polyethylene, UV-stableWater blocking: Gel-filled loose tube, water blocking yarn and tapeStrain relief: FRP central strength member and peripheral strength elementsStripping: Ripcord provided for quick and easy sheath removalFibre Counts: 12f to 144fFibre types available: Single mode to G.652D, G.657A1, G.657A2 (ITU-T) Multimode 62.5/125 OM1 (ISO 11801) Multimode 50/125 OM2, OM3, OM4 (ISO 11801)




Cable mass kg/km 77 78 78 79 81 104 166Sheath thickness mm 1.6 1.6 1.6 1.6 1.6 1.6 1.6


Bending radius (Service) mm 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x ØLong term loading

(fibre strain minimal)*kN 3.0 3.0 3.0 3.0 3.0 3.4 4.2

Max span** meters 40-130 40-130 40-130 40-130 40-130 40-130 40-130Design Spec - CP2598 CP2598 CP2598 CP2598 CP2598 CP2598 CP2598Supply length Km 4 & 6 4 & 6 4 & 6 4 & 6 4 & 6 4 & 6 4 & 6





Low Fire Hazard (LFH) Fibre Optic Cable

Cable ApplicationThis optical fibre cable range has a low flammability, halogen free and low smoke sheath. It has been designed for internal installation directly onto cable trays or into a duct by pulling.


96f

64f 16f 32f 24f 8f 48f

8Fibres per tubeFibres coloured as (1) blue; (2) orange; (3) green; (4) brown; (5) grey; (6) white; (7) red; (8) black


Cable Features and BenefitsSheath: Low flammability, halogen free, low smokeWater blocking: Gel-filled loose tube, water blocking yarn and tapeStrain relief: FRP central strength memberStripping: Ripcord provided for quick and easy sheath removal Fibre counts: 8f to 96fFibre types available: Single mode to G.652D, G.657A1, G.657A2 (ITU-T) Multimode 62.5/125 OM1 (ISO 11801) Multimode 50/125 OM2, OM3, OM4 (ISO 11801) Fire performance: IEC 60332-1



Number of dummy tubes # 5 4 3 2 - - -Central strength member Ø mm 1.9 1.9 1.9 1.9 1.9 3 3/5

Cable mass kg/km 93 94 94 95 97 122 173Sheath Thickness mm 2 2 2 2 2 2 2









Fibre Optic Cable

Cable ApplicationThis optical fibre cable range is designed for direct burial into suitably prepared ground and indoor applications. It has can be window cut at the customer drop location and a fibre tube retracted.


48f 24f

12f

2 Fibres per tubeFibres coloured as (1) blue; (2) orange

Tubes:1stblue; 2nd orange; 3rd green; 4th brown; 5th grey; 6th white, 7th red, 8th, black, 9th yellow, 10th violet, 11th pink, 12th turquoiseTubes: 12 – 24 same sequence as above but (marked)

Cable Features and BenefitsSheath: High density polyethylene, UV-stableStrain relief: 2 x FRP strength membersFibre counts: 12f to 48fFibre types available: Single mode to G.652D, G.657A1, G.657A2 (ITU-T) Multimode 62.5/125 OM1 (ISO 11801) Multimode 50/125 OM2, OM3, OM4 (ISO 11801)

Cable CharacteristicsMax fibres - 12f 24f 36f

Number of tubes - 6 12 24Tube OD/ID Ø mm 1.45/0.8 1.45/0.8 1.45/0.8

strength members Ø mm 0.8 0.8 1.5Cable mass kg/km 42 94 144

Sheath thickness mm 1.5 2.5 3Cable outer Ø mm 8 12 15

Bending radius (Installation) mm 20 x Ø 20 x Ø 20 x ØBending radius (Service) mm 10 x Ø 10 x Ø 10 x Ø

Max fibre pull back distance Mtr 20 20 20Design - CP2604 CP2604 CP2604

Supply length Km 1, 2 & 4 1, 2 & 4 1, 2 & 4Product Code (G.652D version) - 90595 90596 90597



Fibre Optic Cable in Duct for use on Wind Farms & Renewables Sector



ApplicationDesigned for use by the power and telecommunications markets, Emtelles Cable in Duct (CID) products are suitable for a wide range of applications. These products are ideal for use in applications where remote monitoring is required. (SCADA networks for exam-ple).

Features and Benefits With Emtelles CID products fibre optic cables are pre-installed into sub-ducts and transported to site on standard sub-duct drums. Deploying Emtelles CID offers several key advantages such as shorter installation time, reduced logistics and improved quality due to the elimination of cable pulling. Due to the use of high quality Emtelle sub duct the CID solution is ideally suited to installation via mole plough.

Technical DataBelow is Emtelles standard Cable in Duct (CID) range and the maximum OD of cable possible for the duct size. Other duct sizes are available on request if customer cable diameter exceeds the sizes shown on table.

Size Wall Thickness Nom

Mass Nom g/m

Max Pull Max Cable Diam

Generic SpecificationOD ID kg kN

20 16 2.0 111 110 1.0 9 MHT58225 20 2.5 168 170 1.7 9 MHT58225 21 2.0 139 140 1.4 10 MHT58228 24 2.0 162 160 1.6 13 MHT58231 25 3.0 251 260 2.6 14 MHT58232 26 3.0 260 260 2.6 15 MHT58232 27 2.5 220 220 2.2 16 MHT58232 28 2.0 179 180 1.8 17 MHT58234 28 3.0 278 270 2.7 17 MHT58235 28 3.5 329 330 3.3 17 MHT58235 30 2.5 242 250 2.5 19 MHT58240 32 4.0 425 430 4.3 21 MHT58250 41 4.6 612 610 6.1 30 MHT58263 50 6.5 1096 1100 1.1 39 MHT582

Cable in Duct (CID)



Wind farm Fibre Optic Cables (SCADA)

Option A Cable ApplicationThis fibre optic cable has been designed specifically for the wind farm sector. It is a dielectric optical fibre cable with rodent resistance (nylon layer beneath outer sheath) and is ready for direct burial into suitably prepared ground or pulling into existing ducting. This product can also be pre-installed inside a sub duct (Refer to page 12).


72f 48f 12f 36f 24f 16f

12 Fibres per tube (16f – 8 Fibres per tube)Fibres coloured as (1) blue; (2) orange; (3) green; (4) brown; (5) grey; (6) yellow; (7) red; (8) violet; (9) pink; (10) white; (11) black; (12) turquoise

Tubes: 1st Yellow; 2nd Blue; 3rd White; 4thBlack; 5th Red; 6th Green (fillers where necessary)

Cable Features and BenefitsSheath: High density polyethylene, UV-stableRodent Resistance: Nylon Layer beneath outer sheathWater blocking: Gel-filled loose tube, water blocking yarn and tapeStrain relief: FRP central strength member Stripping: Ripcord provided for quick and easy sheath removalFibre Counts: 12f to 72fFibre types available: Single mode to G.652D, G.657A1, G.657A2 (ITU-T) Multimode 62.5/125 OM1 (ISO 11801) Multimode 50/125 OM2, OM3, OM4 (ISO 11801)

Cable CharacteristicsMax fibres - 12f 16f 24f 36f 48f 72f

Number of tubes - 6 6 6 6 6 6Tube OD/ID Ø mm 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6

Number of dummy tubes # 5 4 4 3 2 -Central strength member Ø mm 2.3 2.3 2.3 2.3 2.3 2.3

Cable mass kg/km 106 106 107 107 108 110Sheath thickness mm 1.6 1.6 1.6 1.6 1.6 1.6

Cable outer Ø mm 12.5 12.5 12.5 12.5 12.5 12.5Bending radius (Installation) mm 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x Ø

Bending radius (Service) mm 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x ØMax load (fibre strain 0.4% max)* kN 3.1 3.1 3.1 3.1 3.1 3.1

Design Spec - CP2120A-KG CP2120A-KG CP2120A-KG CP2120A-KG CP2120A-KG CP2120A-KGSupply length Km 2 2 2 2 2 2

Product Code (G.652D version) - 90598 90089 90384 90599 90600 90601


APPROVEDScottish Power

Renewables




Wind farm Fibre Optic Cables (SCADA)

Option B Cable Application This Fibre optic cable has been designed specifically for the wind farm sector. It is a dielectric optical fibre cable with rodent resistance (E-glass tape beneath outer sheath) and is ready for direct burial into suitably prepared ground or pulling into existing ducting. This product can also be pre-installed inside a sub duct (Refer to page 12).


72f 36f 48f 24f 12f

12 Fibres per tubeFibres coloured as (1) blue; (2) orange; (3) green; (4) brown; (5) grey; (6) yellow; (7) red; (8) violet; (9) pink; (10) white; (11) black; (12) turquoise

Tubes: 1stblue; 2nd orange; 3rd green; 4th brown; 5th grey; 6th white (fillers where necessary)

Cable Features and BenefitsSheath: High density polyethylene, UV-stableRodent Resistance: E-glass tape beneath outer sheathWater blocking: Gel-filled loose tube, water blocking yarn and tapeStrain relief: FRP central strength member and peripheral strength elementsStripping: Ripcord provided for quick and easy sheath removalFibre Counts: 12f to 72fFibre types available: Single mode to G.652D, G.657A1, G.657A2 (ITU-T) Multimode 62.5/125 OM1 (ISO 11801) Multimode 50/125 OM2, OM3, OM4 (ISO 11801)

Cable CharacteristicsMax fibres - 12f 24f 36f 48f 72f

Number of tubes - 6 6 6 6 6

Tube OD/ID Ø mm 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6Number of dummy tubes # 5 4 3 2 -

Central strength member Ø mm 2.3 2.3 2.3 2.3 2.3Cable mass kg/km 105 106 106 107 109

Sheath thickness mm 2 2 2 2 2Cable outer Ø mm 11.4 11.4 11.4 11.4 11.4

Bending radius (Installation) mm 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x ØBending radius (Service) mm 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x Ø

Max load (fibre strain 0.3% max)* kN 2.5 2.5 2.5 2.5 2.5Design Spec - CP2055B CP2055B CP2055B CP2055B CP2055BSupply length Km 2 2 2 2 2

Product Code (G.652D version) - 90434 90602 90603 90604 90605


Fibre Optic Cables for use within the Power Sector





t(SPEN) Approved Cables

Option A Cable ApplicationThis fibre optic cable has been designed specifically for Scottish Power Energy Networks. It is a dielectric optical fibre cable with rodent resistance (nylon layer beneath outer sheath) and is ready for direct burial into suitably pre-pared ground or pulling into existing ducting. It is approved for installation into SPEN 110mm telecom duct systems or SPEN Opti-com duct systems.


72f 48f 36f 24f 12f


Tubes: 1st – 4th White; 5th Red; 6th Green (fillers where necessary)

Cable Features and BenefitsSheath: High density polyethylene, UV-stableRodent Resistance: Nylon layer beneath outer sheathWater blocking: Gel-filled loose tube, water blocking yarn and tapeStrain relief: FRP central strength member Stripping: Ripcord provided for quick and easy sheath removalFibre types available: Single mode to G.652D, G.657A1, G.657A2 (ITU-T)Fibre Counts: 12f to 72fFibre attenuation (20°C): 0.35 dB/km max at 1310 nm and 1383 nm 0.21 dB/km max at 1550 nm 0.23 dB/km max at 1625 nm


Number of tubes - 6 6 6 6 6Tube OD/ID Ø mm 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6

Number of dummy tubes # 5 4 3 2 -Central strength member Ø mm 2.3 2.3 2.3 2.3 2.3

Cable mass kg/km 118 119 119 120 122Sheath thickness mm 1.6 1.6 1.6 1.6 1.6

Cable outer Ø mm 12.5 12.5 12.5 12.5 12.5Bending radius (Installation) mm 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x Ø

Bending radius (Service) mm 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x ØMax load (fibre strain 0.4% max)* kN 3.1 3.1 3.1 3.1 3.1

Design Spec - CP2120A CP2120A CP2120A CP2120A CP2120ASupply length Km 2 2 2 2 2



APPROVED



Option B Cable Application This fibre optic cable has been designed specifically for Scottish Power Energy Networks. It is a dielectric optical fibre cable and is ready for direct burial into suitably prepared ground or pulling into existing ducting. It is approved for installation into SPEN 110mm telecom duct systems or SPEN Opti-com duct systems.


72f 48f 12f 36f 24f



Cable Features and BenefitsSheath: High density polyethylene, UV-stableWater blocking: Gel-filled loose tube, water blocking yarn and tapeStrain relief: FRP central strength member Stripping: Ripcord provided for quick and easy sheath removalFibre types available: Single mode to G.652D, G.657A1, G.657A2 (ITU-T)Fibre Counts: 12f to 72fFibre attenuation (20°C): 0.35 dB/km max at 1310 nm and 1383 nm 0.21 dB/km max at 1550 nm 0.23 dB/km max at 1625 nm





Cable outer Ø mm 12.5 12.5 12.5 12.5 12.5Bending radius mm 250 250 250 250 250

Max load (fibre strain 0.4% max)* kN 3.1 3.1 3.1 3.1 3.1Design Spec - CP2119A CP2119A CP2119A CP2119A CP2119ASupply length Km 2 2 2 2 2



APPROVED




(SSE) Cable

Cable Application This fibre optic cable has been designed specifically for Scottish and Southern Energy. It is a dielectric optical fibre cable and is ready for installation into a duct by pulling or directly onto cable trays.


48f 36f 12f 24f 16f

8/12 Fibres per tubeFibres coloured as (1) blue; (2) orange; (3) green; (4) brown; (5) grey; (6) white; (7) red; (8) black; (9) yellow; (10) violet; (11) pink; (12) turquoise

Tubes: 1st Orange; 2nd Blue; 3rd White; 4th White; 5th White; 6th White (fillers where necessary)

Cable Features and BenefitsSheath: Medium density polyethylene, UV-stableWater blocking: Gel-filled loose tube, water blocking yarn and tapeStrain relief: FRP central strength member and peripheral strength elementsStripping: Ripcord provided for quick and easy sheath removalFibre types available: Single mode to G.652D, G.657A1, G.657A2 (ITU-T)Fibre Counts: 12f to 48fFibre attenuation (20°C): 0.35 dB/km max at 1310 nm and 1383 nm 0.21 dB/km max at 1550 nm 0.23 dB/km max at 1625 nm

Cable CharacteristicsMax fibres - 12f (1x12) 16f (2x8) 24f (3x8) 36f (3x12) 48f (6x8)

Number of tubes - 6 6 6 6 6

Tube OD/ID Ø mm 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6Number of dummy tubes # 5 4 3 3 -

Central strength member Ø mm 2.3 2.3 2.3 2.3 2.3Cable mass kg/km 82 82 83 84 84

Sheath thickness mm 1.6 1.6 1.6 1.6 1.6Cable outer Ø mm 10.7 10.7 10.7 10.7 10.7

Bending radius (Installation) mm 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x ØBending radius (Service) mm 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x Ø

Max load (fibre strain 0.4% max)* kN 2.7 2.7 2.7 2.7 2.7Design Spec - CP2385 CP2385 CP2385 CP2385 CP2385Supply length Km 2 2 2 2 2



Fibre Optic Cables for use within the Highways Sector





t(NRTS) Approved Cables

Option A Cable ApplicationThis fibre optic cable has been designed specifically for the Highways sector. It is a dielectric optical fibre cable and is ready for installation into a duct by pulling.


96f 72f 48f 36f 24f 12f


Tubes: 1st Green; 2nd Red; 3rd White; 4th White; 5th White; 6th White; 7th White; 8th White (fillers where necessary)

Cable Features and BenefitsSheath: Medium density polyethylene, UV-stableWater blocking: Gel-filled loose tube and water blocking yarnStrain relief: FRP central strength member and peripheral strength elementsStripping: Ripcord provided for quick and easy sheath removalFibre types available: Single mode to G.652D, G.657A1 (ITU-T)Fibre Counts: 12f to 96fFibre attenuation (20°C): 0.35 dB/km max at 1310 nm and 1383 nm 0.21 dB/km max at 1550 nm 0.23 dB/km max at 1625 nm


Number of tubes - 8 8 8 8 8 8Tube OD/ID Ø mm 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6 2.1/1.6

Number of dummy tubes # 7 6 5 4 2 -Central strength member Ø mm 3.75 3.75 3.75 3.75 3.75 3.75

Cable mass kg/km 118 118 119 119 121 122Sheath thickness mm 2.0 2.0 2.0 2.0 2.0 2.0

Cable outer Ø mm 12.4 12.4 12.4 12.4 12.4 12.4Bending radius (Installation) mm 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x Ø

Bending radius (Service) mm 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x Ø 20 x ØMax load (fibre strain 0.4% max)* kN 2.4 2.4 2.4 2.4 2.4 2.4

Design Spec - CP2388 CP2388 CP2388 CP2388 CP2388 CP2388Supply length Km 4 & 6 4 & 6 4 & 6 4 & 6 4 & 6 4 & 6





Option B Cable Application This fibre optic cable has been designed specifically for the Highways sector. It is a dielectric optical fibre cable and is ready for installation into a duct by pulling.


72f 48f 36f 24f 12f



Cable Features and BenefitsSheath: Medium density polyethylene, UV-stableWater blocking: Gel-filled loose tube, water blocking yarn and tapeStrain relief: FRP central strength member and peripheral strength elementsFibre types available: Single mode to G.652D, G.657A1 (ITU-T)Fibre Counts: 12f to 72fFibre attenuation (20°C): 0.35 dB/km max at 1310 nm and 1383 nm 0.21 dB/km max at 1550 nm 0.23 dB/km max at 1625 nm





Cable outer Ø mm 10.0 10.0 10.0 10.0 10.0Bending radius (Installation) mm 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x Ø

Bending radius (Service) mm 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x ØMax load (fibre strain 0.4% max)* kN 1.5 1.5 1.5 1.5 1.5

Design Spec - CP2387 CP2387 CP2387 CP2387 CP2387Supply length Km 4 & 6 4 & 6 4 & 6 4 & 6 4 & 6






(NRTS) Approved Cables

Option C Cable Application This fibre optic cable has been designed specifically for the Highways sector. It is a dielectric optical fibre cable and is ready for installation into a duct by pulling.


10f 12f 8f 6f 4f 2f

Fibres coloured as (1) blue;(2) orange;(3) green;(4) brown;(5) grey;(6) yellow;(7) red;(8) violet;(9) pink;(10) white;(11) black;(12) turquoiseTubes: 1st White;

Cable Features and BenefitsSheath: Medium density polyethylene, UV-stableWater blocking: Gel-filled loose tube and water blocking yarnStrain relief: peripheral strength elementsFibre types available: Single mode to G.652D, G.657A1 (ITU-T)Fibre Counts: 2f to 12fFibre attenuation (20°C): 0.35 dB/km max at 1310 nm and 1383 nm 0.21 dB/km max at 1550 nm 0.23 dB/km max at 1625 nm


Number of tubes - 1 1 1 1 1 1

Tube OD/ID Ø mm 3.2/2.4 2.1/2.4 2.1/2.4 2.1/2.4 2.1/2.4 2.1/2.4Cable mass kg/km 49 49 49 49 49 49

Sheath thickness mm 2.0 2.0 2.0 2.0 2.0 2.0Cable outer Ø mm 8.0 8.0 8.0 8.0 8.0 8.0

Bending radius (Installation) mm 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x Ø 20 x ØBending radius (Service) mm 10 x Ø 10 x Ø 10 x Ø 10 x Ø 10 x Ø 20 x Ø

Tensile strength kN 1.5 1.5 1.5 1.5 1.5 1.5Design Spec - CP2389 CP2389 CP2389 CP2389 CP2389 CP2389Supply length Km 4 & 6 4 & 6 4 & 6 4 & 6 4 & 6 4 & 6



Fibre Optic Cables for use within the Telecommunications Sector





t(Vodafone) Cables

Option A Cable ApplicationThis optical fibre cable range is all dielectric and designed for installation into a duct by blowing or pulling.


8f 24f 48f

8 Fibres per tubeFibres coloured as (1) blue; (2) orange; (3) green; (4) brown; (5) grey; (6) yellow; (7) red; (8) violetTubes:1st blue; 2nd orange; 3rd green; 4th brown; 5th grey; 6th yellow (fillers where necessary)

Cable Features and BenefitsSheath: High density polyethylene, UV-stableWater Blocking: Gel-filled loose tube, water blocking yarn and tapeStrain Relief FRP central strength memberStripping: Ripcords provided for quick and easy sheath removal Fibre counts: 8f to 48fFibre type: Single mode to G.652D (ITU-T)



Number of dummy tubes # 5 3 -Central strength member Ø mm 1.9 1.9 1.9

Cable mass kg/km 62 62 62Sheath thickness mm 1.6 1.6 1.6

Cable outer Ø mm 8.9 8.9 8.9Bending radius (Installation) mm 20 x Ø 20 x Ø 20 x Ø

Bending radius (Service) mm 10 x Ø 10 x Ø 10 x ØMax Tensile load kN 1.2 1.2 1.2

Design Spec - CP1949 CP1949 CP1949Supply length Km 4 & 6 4 & 6 4 & 6

Product Code (G.652D version) - 90663 90664 90665



Option B Cable Application This optical fibre cable range has a low flammability, halogen free and low smoke sheath. It has been designed for internal installation directly onto cable trays or into a duct by pulling.


8f 24f 48f

8 Fibres per tubeFibres coloured as (1) blue; (2) orange; (3) green; (4) brown; (5) grey; (6) yellow; (7) red; (8) violetTubes:1st blue; 2nd orange; 3rd green; 4th brown; 5th grey; 6th yellow (fillers where necessary)

Cable Features and BenefitsSheath: Low flammability, halogen free, low smokeWater blocking: Gel-filled loose tube, water blocking yarn and tapeStrain relief: FRP central strength memberStripping: Ripcord provided for quick and easy sheath removal Fibre counts: 8f to 48fFibre type: Single mode to G.652D (ITU-T) Fire performance: IEC 60332-1



Number of dummy tubes # 5 3 -Central strength member Ø mm 1.9 1.9 1.9

Cable mass kg/km 102 102 102Sheath thickness mm 2 2 2

Cable outer Ø mm 9.7 9.7 9.7Bending radius (Installation) mm 20 x Ø 20 x Ø 20 x Ø

Bending radius (Service) mm 10 x Ø 10 x Ø 10 x ØMax Tensile load kN 1.2 1.2 1.2

Design Spec - CP2332 CP2332 CP2332Supply length Km 4 & 6 4 & 6 4 & 6

Product Code (G.652D version) - 90666 90667 90668



t(Vodafone) Cables

Option C Cable Application This optical fibre cable is all dielectric and designed for installation into a duct by blowing or pulling.


96f

8 Fibres per tubeFibres coloured as (1) blue; (2) orange; (3) green; (4) brown; (5) grey; (6) yellow; (7) red; (8) violet

Tubes:1st blue; 2nd orange; 3rd green; 4th brown; 5th grey; 6th yellow, 7th red, 8th, violet, 9th pink, 10th white, 11th black, 12th turquoise

Cable Features and BenefitsSheath: Medium density polyethylene, UV-stableWater Blocking: Gel-filled loose tube, water blocking yarn and tapeStrain Relief FRP central strength member with PE sheathStripping: Ripcords provided for quick and easy sheath removal Fibre counts: 96fFibre type: Single mode to G.652D (ITU-T)

Cable CharacteristicsMax fibres - 96f

Number of tubes - 12Tube OD/ID Ø mm 1.7/1.25

Number of dummy tubes # -Central strength member Ø mm 3.0/5.4

Cable mass kg/km 114Sheath thickness mm 1.5

Cable outer Ø mm 12.2Bending radius (Installation) mm 20 x Ø

Bending radius (Service) mm 10 x ØMax Tensile load kN 2.7

Design Spec - CP2331Supply length Km 4 & 6

Product Code (G.652D version) - 90669



Option D Cable Application This optical fibre cable range has a low flammability, halogen free and low smoke sheath. It has been designed for internal installation directly onto cable trays or into a duct by pulling.


24f

8 Fibres per tubeFibres coloured as (1) blue; (2) orange; (3) green; (4) brown; (5) grey; (6) yellow; (7) red; (8) violet

Tube:1st yellow;

Cable Features and BenefitsSheath: Low flammability, halogen free, low smokeWater blocking: Gel-filled loose tube water blocking elementsStrain relief: Aramid yarnsStripping: Ripcord provided for quick and easy sheath removal Fibre count: 8fFibre type: Single mode to G.652D (ITU-T) Fire performance: IEC 60332-1

Cable CharacteristicsMax fibres - 8f

Number of tubes - 1Tube OD/ID Ø mm 2.3/1.5

Number of dummy tubes # -Cable mass kg/km 40

Sheath thickness mm 1.5Cable outer Ø mm 6.0

Bending radius (Installation) mm 20 x ØBending radius (Service) mm 10 x Ø

Max Tensile load kN 1.0Design Spec - CP1950Supply length Km 4 & 6

Product Code (G.652D version) - 90670



Single Mode G.652D Optical Fibre General PropertiesSingle mode fibre shall meet ITU-T G.652D as well as the following requirements, given in table 1 below. Specific properties for preferred fibre manufacturers are available on request.

Table 1 Properties G.652DParameter Value

Glass Diameter 125 ± 0.7microns

Core Non Circularity ≤ 6%

Core-Concentricity error ≤ 0.5 micron

Cladding Non Circularity < 1%

Coating Diameter (Uncoloured) 235 microns minimum250 microns maximum

Coating Diameter (Self Coloured) 250 ±15 microns

Colouring Layer 2 to 8 microns

Coating-Cladding Concentricity < 12 microns

Attenuation ≤ 0.34 dB/km 1310nm )≤ 0.20 dB/km 1550nm ) 100% of fibre≤ 0.23 dB/km 1625nm )

Attenuation Uniformity No point discontinuity ≥ 0.05 dB at 1310and 1550nm

Attenuation at water peak <0.34 dB/km at 1383 ±3nm(100% of fibre)

Chromatic Dispersion: Zero Dispersion wavelength ZD Slope Max dispersion at 1550nm

1302 – 1322nm< 0.092 ps/nm.nm.km18 ps/nm.km

Temperature Sensitivity ≤ 0.05dB/km increment over range –60° to +85°C at 1550 and 1310nm

Humidity Sensitivity ≤ 0.05 dB/km increment over range 4 to 93% RH at 1550 and 1310nm

Water Immersion ≤ 0.05 dB/km increment during and after 3 month water soak. Nominally 20 ±3°C.

Bend Sensitivity 100 turns of fibre at 50mm diameter. Attenuation rise to be ≤0.1dB at 1550nm and 1625nm 1 turn of fibre at 32mm diameter. Attenuation rise to be ≤ 0.5dB at 1550 and 1625nm.

Mode Field Diameter 9.3 ±0.5 microns 1310nm10.4 ±0.8 micron at 1550nm

Cut Off Wavelength ≤1260nm

Proof Test ≥ 0.7 GPa

Stress Corrosion susceptibility parameter ≥ 20

Coating Strip Force 1.3 to 6N

Appendix A - Fibre Properties Tables



Single Mode G.657A1 and A2 Optical Fibre General PropertiesSingle mode fibre shall meet ITU-T G.657 A1 and A2 as well as the following requirements, given in the table 1 below. Specific properties for preferred fibre manufacturers are available on request.

Table 1 Properties For G.657A1 and A2Parameter Value

Glass Diameter 125 ± 0.7 microns

Core-Clad Concentricity ≤0.5 micron

Cladding Non Circularity <1%

Coating Diameter (Uncoloured) 245 ± 10 microns

Coating Diameter (Self Coloured) 250 ± 15 microns


Coating-Cladding Concentricity <12 microns

Attenuation ≤0.34 dB/km 1310nm)≤0.20 dB/km 1550nm) 100% of fibre≤0.23 dB/km 1625nm)

Point discontinuity < 0.05 dB 1310,1550nm

Attenuation versus wavelength (max difference) 1285-1330 nm: 0.03dB1525-1575 nm: 0.02dB

Temperature Sensitivity ≤0.05dB/km increment over range –60 to +85°C at 1550 and 1310 nm

Humidity Sensitivity ≤0.05 dB/km increment over range 4 to 93% RHat 1550 and 1310nm

Water Immersion ≤0.05 dB/km increment during and after 14 day water soak. At 20 ± 3°C.

Bending Sensitivity Type A1 Fibre- 10 turns of fibre at 30mm diameter. Attenuation rise to be ≤0.25dB at 1550nm and ≤1dB at 1625nm. 1 turn of fibre at 20mm diameter. Attenuation rise to be ≤ 0.75dB at 1550 and ≤ 1.5dB 1625nm.

Type A2 Fibre- 10 turns of fibre at 30mm diameter. Attenuation rise to be ≤0.03dB at 1550nm and ≤0.1dB at 1625nm. 1 turn of fibre at 20mm diameter. Attenuation rise to be ≤ 0.1dB at 1550 and ≤ 0.2dB 1625nm. 1 turn of fibre at 15mm diameter. Attenuation rise to be ≤ 0.5dB at 1550 and ≤ 1dB 1625nm.

Mode Field Diameter 8.6 to 9.5 ±0.4 microns 1310nm

Zero Dispersion slope (S0) ≤ 0.092ps/nm2. km

Dispersion Values 1550nm: ≤ 18 ps/nm. Km 1625nm: ≤ 22 ps/nm. Km

Cable Cut Off Wavelength < 1260nm

Proof Test ≥ 0.69 GPa

Stress Corrosion susceptibility parameter ≥ 20

Coating Strip Force 1.0 to 10 N



Multimode 50/125 and 62.5/125 Optical Fibre General PropertiesMultimode 50/125 and 62.5/125 fibres compliant with IEC60793-2-10 types A1a, A1a.2 or A1b, and meet the re-quirements of Tables 1 to 6.

Table 1 StandardsEmtelle Class Fibre Core/Cladding

(microns)ISO/IEC 11801 IEC 60793-2-10 TIA/EIA

OM1 and OM1 HBW 62.5/125 type OM1 type A1b 492AAAA-A

OM2 and OM2 HBW 50/125 type OM2 type A1a.1 492AAAB

OM3 50/125 type OM3 type A1a.2 492AAAC-A

OM4 50/125 type OM4 TBA 492AAAD

Table 2 Bandwidth and Transmission CapacityFibre Class Bandwidth (MHz.km) *1000Base-SX

Gigabit Ethernet Reach (m)at 850nm

**10GBase-SR10 Gigabit Ethernet

Reach (m)at 850nm

Legacy LED Based Laser Based

OFLa RMLb EMBc

850nm 1300nm 850nm 850nm

OM1 200 500 220 - 300 -

OM1 HBW 200 600 220 - 300 -

OM2 500 500 - 510 600 -

OM2 HBW 600 1200 - - 600 850nm& 1300nm -

OM3 1500 500 - 2000 1000 300

OM4 3500 500 - 4700 1100d 550d

Table 3 AttenuationFibre Class *Group Index of Refraction

850nm 1300nm

62.5/125 Fibres: OM1 and OM1 HBW 3.0 0.6

50/125 Fibres: OM2, OM2 HBW, OM3 and OM4 2.3 0.6

Table 4 Group Index of RefractionFibre Class Maximum Attenuation (dB/km)

850nm 1300nm

62.5/125 Fibres: OM1and OM1 HBW

Required Range 1.491 - 1.496 1.490 – 1.495

*Supplier Value

50/125 Fibres: OM2, OM2 HBW, OM3 and OM4

Required Range 1.480 - 1.496 1.476 - 1.487

*Supplier Value

Table 5 Numerical ApertureFibre Class Numerical Aperture

Required Range *Supplier Value

62.5/125 Fibres: OM1 and OM1 HBW 0.275 ± 0.015

50/125 Fibres: OM2, OM2 HBW, OM3 and OM4 0.200 ± 0.015



Table 6 Properties For All Multimode FibresParameter Value

Glass Diameter 125 + 2 microns

Core Non Circularity < 6%

Core-Clad Concentricity < 3.0 microns

Cladding Non Circularity < 2%

Coating Diameter 245+ 10 microns

Coating Diameter 250 + 15 microns


Coating-Cladding Concentricity < 12 microns

Temperature Sensitivity < 0.2 dB/km increment over range –60 to +85C at 850 and 1300 nm

Humidity Sensitivity < 0.2 dB/km increment over range 4 to 93% RH

Bend Sensitivity 100 turns of fibre at 75mm diameter. Attenuation rise to be < 0.5 dB/km at 850 and 1300 nm

Chromatic Dispersion As per FDDI standard

Proof Test > 0.7 GPa

Stress Corrosion susceptibility parameter > 20

Coating Strip Force 1.0 to 6N

Lengths 8.8km, 16.8 & 17.6km

www.emtelle.comwww.fibre-to-the-home.com

HeadquartersEmtelleHaughheadHawickTD9 8LFUnited Kingdom

Tel : + 44 (0)1450 364000Fax : + 44 (0)1450 364001E: [email protected]

Emtelle Europe BVHoefseweg 13821 AE AmersfoortThe Netherlands

Sales Benelux and ACHTel: +31 85 273 1819E: [email protected]

Sales GermanyTel: +49 2369 2069436E: [email protected]

Sales Eastern EuropeTel: +491736203705E: [email protected]

Emtelle ScandinaviaVardevej 1407280 Sønder FeldingDenmark

Tel: +45 86 28 84 88Fax: +45 86 28 81 52E: [email protected]

Emtelle Asia PacificNo. 4, Jalan PJU 1A/8Ara DamansaraTaman Perindustrian Jaya47301 Petaling JayaSelangorMalaysia

Tel: +60 (0)3 7845 4406Fax: +60 (0)3 7845 4459 E: [email protected]

Emtelle Australia

Commercial Contact : Jason Hanlon Tel: +61 [email protected] Technical Contact : Graham Morris Tel: +61 400793300E: [email protected]

emtelle fibre optic cables catalogue 2017 · all emtelle manufactured fibre optic cables complies...

Documents