e.m.c sample question
TRANSCRIPT
-
8/11/2019 E.M.C Sample Question
1/38
64. Which one of the following are the basic types of static stresses to
which a material can be subjected?
(a) Compression
(b) Hardness, reduction in area,
(c) Shear, tensile
(d) Both a and c are correct
65. Which one of the following are mechanical properties of materials?
(a) Strength, hardness, toughness
(b) Ductility, elasticity, fatigue
(c) Boiling point, conductivity, density
(d) Both a and b are correct
66. In machine tools where different components are made of different
components, the assembly may jam, or become too loose and vibrate,
when the temperature changes. Their design must account and
compensate for the materials used their?
(a) Ductility
(b) Density
(c) Fatigue
(d) Thermal expansion
67. The plastic region of the stress-strain curve for a metal is characterized
by a proportional relationship between stress and strain?
(a) True (b) false
68. Which one of the following materials has the highest hardness?
(a) Aluminum,(b) Diamond,
(c) Steel,
(d) Titanium
-
8/11/2019 E.M.C Sample Question
2/38
69. Most hardness tests involve pressing a hard object into the surface of a
test specimen and measuring the indentation (or its effect) that results?
(a) True (b) false
70. Steel is a good material for the wrecking ball used to demolish old
buildings because of Its?
(a) High density
(b) Low elasticity
(c) High coefficient of linear thermal expansion
(d) Low fatigue
71. Which one of the following metals has the lowest density?
(a) Aluminum
(b) Copper
(c) Magnesium
(d) Tin
72. Due to its poor thermal conductivity, titanium can be easily machined
on a milling machine?
(a) True (b) false
73. Which of the following pure metals is the best conductor of electricity?
(a) Aluminum,
(b) Copper,
(c) Gold
(d) Silver
74. Cast iron is a ferrous alloy with up to 2% carbon?
(a) True (b) false
-
8/11/2019 E.M.C Sample Question
3/38
75. Bronze is a metal alloy consisting primarily of copper and tin?
(a) True (b) false
76. Brass is an alloy of copper and zinc?
(a) True (b) false
77. Which one of the following casting processes is the most widely used?
(a) Centrifugal casting
(b) Die casting
(c) Investment casting
(d) Sand casting
78. Compared to others casting processes, investment casting process is
the best solution for manufacturing of?
(a) Engine blocks
(b) Gears
(c) Jewellery
(d) Car wheels
79. in sand casting, the volumetric size of the pattern is?
(a) Bigger than
(b) The same size
(c) Smaller than the cast part
(d) All the above
80. Which of the following casting processes are expendable mold
operations?
(a) Investment casting
(b) Sand casting
(c) Shell molding
(d)All the above
-
8/11/2019 E.M.C Sample Question
4/38
81. Shell molding is best described by which one of the following?
(a) Casting operation in which the molten metal has been poured out after a thin
shell has been solidified in the mold
(b) Casting process in which the mold is a thin shell of sand binded by a
thermosetting resin
(c) Sand casting operation in which the pattern is a shell rather than a solid form
(d) Casting operation used to make artificial sea shells
82. Investment casting is also known by which one of the following
names?
(a) fast-payback molding
(b) full-mold process
(c) Lost pattern process
(d) lost-wax process
83. Which of the following casting processes are permanent mold
operations?
(a) Centrifugal casting
(b) Die casting
(c) Vacuum casting.
(d) All the above
84. Which of the following are advantages of die casting over sand
casting?
(a) Better surface finish
(b) Closer tolerances(c) Mold can be reused
(d) All the above
-
8/11/2019 E.M.C Sample Question
5/38
85. Identify the material with the lowest ductility?
(a) Copper
(b) Graphite
(c) Aluminum
(d) Platinum
86. In a hot chamber die casting machine the melting pot?
(a) Melting pot is separate from the machine
(b) Melting pot is an integral part of the machine
(c) Melting pot may have any location
(d) There is no need for melting pot
87. % C in medium carbon steels ranges from?
(a) 0.30.4
(b) 0.3 0.5
(c) 0.3 0.6
(d) None
88. Stainless steel is also known for its?
(a) High strength
(b) High corrosion resistance
(c) High ductility
(d) Brittleness
89. In white cast irons, carbon is present as?
(a) Graphite flakes
(b) Graphite nodules
(c) Cementite
(d) Carbon does not exist
90. Not an important heat treatment process parameter is?
(a) Heating rate
(b) Temperature
(c) Cooling rate
(d) Atmosphere
-
8/11/2019 E.M.C Sample Question
6/38
91. Final structure of austempered steel is?
(a) Pearlite
(b) Ferrite + graphite
(c) Bainite
(d) Martensite
92. Sand casting is which of the following types?
(a) Expendable mold (b) Permanent mold
93. The upper half of a sand casting mold is called which of the following?
(a) Cope (b) drag
94. In casting, a flask is which one of the following?
(a) Beverage bottle for foundry men
(b) Box which holds the cope and drag(c) Container for holding liquid metal
(d) Metal which extrudes between the mold halves
95. in foundry work, a runner is which one of the following?
(a) Channel in the mold leading from the downsprue to the main mold cavity
(b) Foundry man who moves the molten metal to the mold
(c) Vertical channel into which molten metal is poured into the mold
(d) All the above
-
8/11/2019 E.M.C Sample Question
7/38
96. Turbulence during pouring of the molten metal is undesirable for which
of the following reasons?
(a) It causes discoloration of the mold surfaces
(b) It increases erosion of the mold surfaces
(c) It increases the formation of metallic oxides that can become entrapped during
solidification
(d) B and c are correct
97. Total solidification time is defined as which one of the following?
(a) Time between pouring and complete solidification
(b) Time between pouring and cooling to room temperature
(c) Time between solidification and cooling to room temperature
(d) Time to give up the heat of fusion
98. A riser in a casting is described by which of the following?
(a) Metal that is not part of the casting
(b) Source of molten metal to feed the casting and compensate for shrinkage
during solidification
(c) Waste metal that is usually recycled
(d) All the above
99. Which best describes what is sought by nondestructive testing?
(a)Surface irregularities
(b)Subsurface holes and cracks
(c)Any breaks in the continuity of metal structure
(d)A direct test method
100. Nondestructive testing is a method of locating which of the following?
(a)Discontinuations
(b)Dislocations
(c)Discontinuities
(d)Disturbances
-
8/11/2019 E.M.C Sample Question
8/38
101. For which one of the following reasons is a green mold named?
(a) Green is the color of the mold
(b) Moisture is contained in the mold
(c) Mold is cured
(d) Mold is recycled
102. Which of the following provides the NDT inspector with a brief outline
of the steps to perform a test on a specific item?
(a)Code
(b)Standard
(c)Procedure(Instruction)
(d)Specification
103. Metal has a property of:
(a)Failing to unite if too hot
(b)Retaining large grain structure when forged
(c)Occupying more space when molten than when a solid
(d)Occupying more space when a solid than when a molten
104. A typical temperature range to stress relieve ferrite steel is?
(a) 100-150 degrees Celsius
(b) 250-300 degrees Celsius(c) 600-650 degrees Celsius(d) 900-950 degrees Celsius
105. Which of the following qualifies as a precision casting process?
(a) Ingot casting
(b) Investment casting,
(c) Plaster mold casting
(d) B and c are correct
-
8/11/2019 E.M.C Sample Question
9/38
106. Which of the following casting processes are permanent mold
operations?
(a) Centrifugal casting
(b) Die casting
(c) Sand casting(d) A and b are correct
107. Which of the following metals would typically be used in die casting?
(a) Aluminum
(b) Tin
(c) Zinc
(d) All the above
108. The ease with which a solid union may be made between two parts bywelding is known as?
(a)Weld ability(b)Joining(c)Buttering(d)Soldering
109. Cupolas are furnaces used to melt which of the following metals?
(a) Aluminum
(b) Cast iron(c) Steel
(d) Zinc
110. A misrun is which one of the following defects in casting?
(a) globules of metal becoming entrapped in the casting
(b) Metal is not properly poured into the downsprue
(c) Metal solidifies before filling the cavity
(d) Micro porosity
-
8/11/2019 E.M.C Sample Question
10/38
111. Products used in load carrying applications require more carefultesting because?
(a) Failure can cause loss of life(b) Failure can cause loss of use of the product(c) Failure can be expensive(d) All the above
112. Loads which are most likely to cause failure are?
(a) Single direction(b) Multi directional(c) Duo directional(d) Phase orientated
113. The general term for a local variation in material continuity is called?
(a) A discontinuity(b) A defect(c) An indication(d) A crack
114. Where an unacceptable condition occurs in a material, due to localvariations in material continuity the term given specifically to this is?
(a)A discontinuity(b)A flaw
(c)A defect(d)Any of the above
115. Which of the following could be considered a discontinuity?
(a)Crack(b)Change of section(c)Drilled holed(d)All the above
116. The study and description of a material property related to analyticalstudies and testing attempts to quantify the toughness of a material is
known as?
(a)Fracture mechanics(b)Acceptance standards(c)Defect reliability(d)Defect analysis
-
8/11/2019 E.M.C Sample Question
11/38
-
8/11/2019 E.M.C Sample Question
12/38
123. Changing a material's shape can be accomplished in which of thefollowing states?
(a)Solid(b)Liquid(c)Plastic(d)All of the above
124. Which of the following is an example of reshaping?
(a)Casting(b)Forging(c)Grinding(d)All of the above
125. The process of solidification during casting can be likened to that ofthe?
(a)Forging process(b)Rolling process(c)Welding process(d)Extrusion process
126. Reshaping of a material while still in a plastic or semi-solid form iscalled?
(a)Casting(b)Rolling
(c)Extrusion(d)Both b and c are correct
127. Which of the following could be referred to as an engineeringmaterial?
(a)Plastic(b)Concrete(c)Glass(d)All of the above
128. Which of the following properties of a material can be used to predictthe deflection of a certain size beam under known loads?
(a)Tensile strength(b)Elastic limit(c)Younges modules(d)Ductility
-
8/11/2019 E.M.C Sample Question
13/38
129. Which of the following must be considered when choosing anengineering material for a particular application?
(a)Cost(b)Loading(c)Mechanical properties(d)Any of the above
130. Which of the following could effect the properties of an engineeringmaterial?
(a)Composition(b)Heat treated condition(c)Composition and heat treated condition(d)Composition, heat treated condition and crystal structure
131. Which of the following is classed as a chemical property?
(a)Electrical conductivity(b)Thermal conductivity(c)Corrosion resistance(d)Machine resistance
132. Which of the following is classed as a Physical property?
(a)Density(b)Conductivity(c)Melting point
(d)All of the above
133. A test designed to determine a materials cast ability would beclassified as looking for a?
(a)Mechanical property(b)Physical property(c)Processing property(d)Chemical property
134. Internal forces acting upon imaginary planes cutting the body beingloaded are?
(a)Stresses(b)Pressures(c)Strain(d)Fatigues
-
8/11/2019 E.M.C Sample Question
14/38
135. A stress caused by forces at an angle to the plane is known as a?
(a)Comprehensive stress(b)Tensile stress(c)Normal stress(d)Shear stress
136. A non-destructive test is usually classified as a?
(a)Indirect test(b)Direct test(c)Destructive test(d)Indirect and direct test
137. If a material is loaded until its elastic limit is exceeded, whatcondition will occur?
(a)The material may fracture(b)The material may be work hardened(c)The material will show no harmful effects(d)The material may fracture and the material may be work hardened
138. The ultimate strength of material is?
(a)Lower than the breaking strength for ductile materials(b)Lower than the rupture strength for ductile materials(c)The same as the breaking strength for brittle materials
(d)None of the above
139. The modulus of elasticity is also known as?
(a)Stress's modulus(b)Young's modulus(c)Strain's modulus(d)Resilience
140. Which of the following materials exhibits better compressive strengththan tensile strength?
(a)Cast iron(b)Concrete(c)Wood(d)All the above
-
8/11/2019 E.M.C Sample Question
15/38
141. When a metal is very brittle which test is used to replace the tensiletest?
(a)The shear test(b)The transverse rupture test(c)The compression test(d)The endurance test
142. Fatigue failure may initiate from?
(a)An area of corrosion(b)An internal flaw(c)A surface notch(d)All the above
143. Metal forming such as rolling results in?
(a)Plastic flow of metal.(b)Elongation of existing defects perpendicular to the rolling direction.(c)Directional properties which are always beneficial for secondary forming
operations.(d)The flatting out of defects which makes them more easily detectable by most
NDT methods.
144. Hardness tests can be used to determine material?
(a)Hardness
(b)Composition(c)Heat treated condition(d)All the above
145. The superficial Rockwell test is carried out on materials that?
(a)Only allow very small surface blemishes(b)Are very ductile(c)Have very large surface areas(d)None of the above
146. Which of the following is a notched bar test?
(a)Charpy(b)Creep(c)Izod(d)Both a and c are correct
-
8/11/2019 E.M.C Sample Question
16/38
147. To what angle should a bend test be normally bent?
(a)180 degrees(b)150 degrees(c)90 degrees(d)None of the above
148. Which of the following is a hardness test?
(a)Rockwell(b)Creep(c)Charpy(d)Izod
149.Grain direction in steel bar stock is always?
(a)Though the length of the bar(b)Though the width of the bar(c)Spread out in all directions(d)A bar of steel has no grain
111. All the above112. Multi directional113. A discontinuity114. A defect
115. All the above116. Fracture mechanics117. A defect118. Elastic deformation119. At low temperatures120. It is generally used in applications where the loads are principallycomprehensive121. Manufacturing process122. Shape and Properties123. All of the above124. Forging125. Welding process
126. Rolling and Extrusion127. Plastic128. Younges modules129. Any of the above130. Composition, heat treated condition and crystal strucure131. Corrosion resistance132. All of the above133. Processing property
-
8/11/2019 E.M.C Sample Question
17/38
134. Stresses135. Shear stress136. Indirect test137. The material may fracture and the material may be work hardened138. The same as the breaking strength for brittle materials139. Young's modulus140. All the above141. The transverse rupture test142. All the above143. answer is:A144. All the above145. Only allow very small surface blemishes146. Charpy and Izod147. 180 degrees148. Rockwell149. Shear stresses
150. Electrons in an atom can exist?
(a)Only in exact energy levels(b)Only in exact energy shells
(c)At random throughout the atom(d)In Exact energy levels and in exact energy shells
151. A material that has high hardness and good electrical and thermalconnectivity is known as?
(a)A plastic material(b)A ceramic material(c)A metallic material(d)A liquid material
152. What term is used to define the change of state directly from solid togas?
(a)Crystallization(b)Vaporization(c)Sublimation(d)None of the above
-
8/11/2019 E.M.C Sample Question
18/38
153. Which of the following is a crystal lattice that has nine atoms, eight ateach corner and one centrally between them?
(a)Hexagonal close packing(b)Body centered cubic(c)Face centered cubic(d)Body centered tetragonal
154. Which of the following materials is Body centered cubic at roomtemperature?
(a)Copper(b)Gold(c)Iron(d)Nickel
155. A property of a fine grain material is that it will?
(a)Machine more easily than Corse grain(b)Case harden more easily than coarse grain(c)Have higher strength than coarse grain(d)All the above
156. Permanent deformation can occur in which of the following ways?
(a)Static deformation(b)Twinning deformation(c)Elastic deformation(d)All of the above
157. Work done to produce plastic deformation below a materials re-crystallization temperature is known as?
(a)Recovery work(b)Cold work(c)Twinning(d)Plasticity work
158. Solution heat treatment requires which of the following?
(a)To dissolve maximum amount of equilibrium precipitant in the solid solution(b)Very high temperatures(c)Diffusion times in excess of 24 hours(d)All of the above
-
8/11/2019 E.M.C Sample Question
19/38
159. Precipitation hardening is most commonly carried out on which of thefollowing materials?
(a) Carbon steel(b) Lead(c) Copper(d) Aluminum
160. Allotropic changes occur in the?
(a) Liquid state(b) Solid state(c) Gaseous state(d) Liquid or solid state
161. Which of the following is an allotropic material?
(a) Iron(b) Copper(c) Lead(d) Aluminum
162. A heat treatment process that requires a material to be heated aboveits critical temperature for some period of time for carbon to unite in solidsolution with iron in the gamma or F.C.C. lattice is known as?
(a)Spherodizing(b)Annealing(c)Austentitization(d)Normalizing
163. A process used to decrease hardness, increase ductility andoccasionally improve machinability of high carbon steels is called?
(a)Annealing(b)Austenitization(c)Spheroidizing
(d)Stress relieving
164. A treatment that is used to give minimum hardness and maximumductility of steel is?
(a)Annealing(b)Austenitization(c)Spheroidizing
-
8/11/2019 E.M.C Sample Question
20/38
(d)Normalizing
165. Localized corrosion causing deep extend holes is known as?
(a)Fisives(b)Pitting(c)Worm holes(d)None of the above
166. Which of the following is classed as permanent deformation?
(a)Twinning(b)Rotational deformation(c)Twinning and Slip(d)All of the above
167. Annealing will achieve which of the following properties?
(a)Increase ductility and decrease hardness(b)Increase ductility and increase hardness(c)Decrease ductility and increase hardness(d)Decrease ductility and decrease hardness
168. Of the following metals which is most susceptible to corrosion by seawater?
(a)Gold(b)Copper(c)Zinc(d)Lead
169. During the hardening of steel which of the following quenching mediawill produce the severest quench?
(a)Water(b)Brine(c)Oil
(d)Air
170. Which is the most common metallic element found on earth?
(a)Iron(b)Titanium(c)Aluminum(d)Magnesium
-
8/11/2019 E.M.C Sample Question
21/38
171. The product of a blast furnace is known as?
(a)Iron(b)Steel(c)Pig iron(d)A pig
172. What is the approximate carbon content of Pig iron?
(a)1-2%(b)2-3%(c)3-4%(d)4-5%
173. When the carbon content of iron is reduced below 2% it is called?
(a)Steel(b)Gray iron(c)White iron(d)Ductile iron
174. A Bessemer converter is?
(a)A method of producing cast iron(b)A method of producing pig iron(c)A method of producing wrought iron
(d)A method of producing steel
175. Practically all steel is made with the use of?
(a)Hydrogen(b)Oxygen(c)Nitrogen(d)Helium
176. The carbon content of low carbon steel is?
(a) 6-25 points of carbon
(b) 25-50 points of carbon(c) 0.06% -0.25% of carbon(d) 6-25 points and 0.06% -0.25% of carbon
-
8/11/2019 E.M.C Sample Question
22/38
177. The carbon content of high carbon steel is?
(a)6-25 points of carbon(b)25-50 points of carbon(c)50-160 points of carbon(d)Over 160 points of carbon
178. An alloy steel is a steel containing one or more?
(a)Elements(b)Atoms(c)Mixtures(d)Components
179. What do the letters AISI stand for?
(a)American Institute of Steel Industries(b)American Iron and Steel Industries(c)American Industries of Steel Institutes(d)American Iron and Steel Institute
180. Which of the following is a classification of Stainless Steel?
(a)Ferrite(b)Martensitic
(c)Austenitic(d)All of the above
181. Austenitic stainless steel most typically contain?
(a)18% Chromium 8% Nickel(b)15% Chromium 10% Nickel(c)10% Chromium 15% Nickel(d)8% Chromium 18% Nickel
182. Which of the following metals can be magnetized?
(a)Martensitic stainless(b)Ferrite stainless(c)Austenitic stainless(d)Martensitic stainless and Ferrite stainless
-
8/11/2019 E.M.C Sample Question
23/38
183. Which of the following may be used as an alloying element of steel?
(a)Copper(b)Nickel(c)Aluminum(d)All the above
184. Steel has a carbon content of less than?
(a)4%(b)3%(c)2%(d)1%
185. Which is the main alloying element of austenitic stainless steels?
(a)Nickel(b)Manganese(c)Molybdenum(d)Chromium
186. Grain boundaries are areas of a metal micro structure:
(a)Where high melting point constituents are concentrated(b)Made up of rows of atoms arrayed in straight lines(c)That are not attacked by etchants and generally stand in relief during
metallografic examination.(d)Where low melting impurities tend to concentrate
187. Tool and die steels are classed as?
(a)Low carbon steels(b)Medium carbon steels(c)High carbon steels(d)Alloy steels
188. Which of the following alloying additions are used to produce tool anddie steels?
(a)Nickel(b)Chromium(c) Manganese(d) Both Chromium and Manganese
-
8/11/2019 E.M.C Sample Question
24/38
150. In Exact energy levels and in exact energy shells151. A metallic material152. Sublimation153. Body centered cubic154. Iron155. Have higher strength than coarse grain156. Twinning deformation
157. Cold work158. To dissolve maximum amount of equilibrium precipitant in the solid solution159. Aluminum160. Solid state161. Iron162. Austentitization163. Annealing164. Spheroidizing165. Pitting166. All of the above167. Increase ductility and decrease hardness
168. Zinc169. Brine170. Aluminum171. Pig iron172. 3-4%173. Steel174. A method of producing steel175. Oxygen176. 6-25 points and 0.06%-0.25% of carbon177. 50-160 points of carbon178. Elements179. American Iron and Steel Institute
180. All of the above181. 18% Chromium 8% Nickel182. Martensitic stainless and Ferrite stainless183. All the above184. 1%185. Chromium186. answer is: D187. High carbon steels
-
8/11/2019 E.M.C Sample Question
25/38
188. Both Chromium and Manganese
189. Which of the following is classified as a non-ferrous light alloy?
(a)Beryllium base(b)Zinc base(c)Tin base(d)Copper base
190. Of the following, which is considered the most important structuralnon-ferrous metal?
(a)Copper(b)Zinc(c)Tin(d)Aluminum
191. Aluminum cannot be used in most areas where vibrations combinewith high stress. There are special care has to be taken to remove allstress raisers. Which below is considered a stress raiser?
(a)A notch(b)A scratch(c)A sudden change of section(d)All of the above
192. When applying the term annealed to pure aluminum it is interpreted
to mean?
(a)Work hardening(b)Re-crystallization(c)Stress releasing(d)Normalizing
193. Which NDT method can be used to give general sorting of aluminumalloys?
(a)UT(b)MT
(c)RT(d)ET
194. Which metal is most used in electrical work, wiring, etc?
(a)Copper(b)Brass(c)Aluminum
-
8/11/2019 E.M.C Sample Question
26/38
(d)Steel
195. It is generally understood that the principal alloying elements ofbrass are?
(a)Copper and tin(b)Copper and zinc(c)Bronze and tin(d)Tin and zinc
196. Which two NDT methods are usually used to inspect Magnesiumcomponents?
(a)Radiography and penetrant(b)Radiography and magnetic particle(c)Ultrasonic and magnetic particle(d)Ultrasonic and penetrant
197. Wrought zinc and its alloys have very little NDT inspection on them,when a material is plated with zinc it is known as?
(a)Anodizing(b)Wrapping(c)Galvanizing(d)Flashing
198. Thermoplasting can be?
(a)Melted down and re-used without loss of properties(b)Softened by heat(c)Will char when heated(d)Melted down and re-used without loss of properties and softened by heat
199. Thermosetting plastics are?
(a)Rigid(b)Deteriorated by heat(c)Charred by heat(d)All of the above
200. Which of the following non-ferrous metals is classed as a light alloy?
(a)Beryllium base(b)Zinc base(c)Tin base(d)All of the above
-
8/11/2019 E.M.C Sample Question
27/38
201. Which of the metals listed below has the highest strength to weightratio?
(a)Beryllium(b)Titanium(c)Aluminum(d)Zinc
202. One of the major drawbacks of magnesium alloys is?
(a)Poor corrosion resistance(b)Notch sensitivity(c)High density(d)More expensive than using beryllium which exhibits similar properties
203. Which of the following non-ferrous metals is almost exclusively die-
cast?
(a)Aluminum(b)Copper(c)Magnesium(d)Zinc
204. Cobalt is used as an alloying constituent in?
(a)Bearing alloys(b)Solders
(c)Permanent magnets(d)Dental alloys
205. Manufacturing is a term used generally to describe the ??? of a bulkmaterial?
(a)Designing(b)Production(c)Shape changing(d)Casting
206. Which of the following is classed as a manufacturing process?
(a)Casting(b)Welding & Machining(c)Rolling(d)All of the above
-
8/11/2019 E.M.C Sample Question
28/38
207. Which of the following manufacturing processes is the mosteconomical method of producing complex shapes?
(a)Casting(b)Forging(c)Rolling(d)Welding
208. In modern manufacturing industries which of the following factorsare considered?
(a)Markets(b)Product life(c)Manufacturing process(d)All of the above
209. Which of the following is required when making a sand casting?
(a)A mold(b)A pattern(c)A flask(d)All of the above
210. Shrinkage within a casting can occur in which of the following states?
(a)Liquid state(b)Solidification(c)Solid state
(d)All of the above
211. Pattern makers shrinkage occurs in?
(a)Liquid state of casting(b)Solidification state of casting(c)Solid state of casting(d)All of the above
212. When a change of wall thickness is required in a casting what wouldgive the best design results?
(a)Sudden section change(b)Small radii(c)Large radii(d)All of the above
-
8/11/2019 E.M.C Sample Question
29/38
213. Metal is fed into the casting cavity through a ??? system?
(a)Flow system(b)Gating system(c)Pouring system(d)Riser system
214. Wells outside the normal finished casting are there to allow for?
(a)Gas evolution(b)Sand erosion(c)Shrinkage(d)Airlocks
215. Directional solidification in Castings is helped by the use of?
(a)Cores
(b)Feeder headers(c)Chills(d)Chaplets
216. Where holes or cavities are required in the finished casting a ??? isused in the moulding stage?
(a)Chill(b)Ingate(c)Riser(d)Core
217. Green sand is a mixture of sand and?
(a)Clay(b)Silicon(c)Water(d)Both a and c are correct
218. The upper half of a flask is called?
(a)A drag(b)A cope
(c)A draft(d)A mould
-
8/11/2019 E.M.C Sample Question
30/38
219. Small metal supports which become part of the casting during pouringare called?
(a)Chills(b)Chaplets(c)Cores(d)Risers
220. Which of the following casting processes is best used for smallintricate casting up to 2kg - requiring close tolerances?
(a)Centrifugal casting(b)Investment casting(c)Continuous casting(d)Permanent mold casting
221. The casting process which gives improved material density towardsthe outside of the mold is?
(a)Centrifugal casting(b)Investment casting(c)Continuous casting(d)Permanent mold casting
222. Splashed metal entrapped by molten metal that does not re-fuse is
called?
(a)Hot tear(b)Chill(c)Inclusion(d)Cold shut
223. The bottom part of the flask is known as the?
(a)Cope(b)Bottom board(c)Drag
(d)Runner
-
8/11/2019 E.M.C Sample Question
31/38
224. Which of the following is used to give preferential solidification ofcastings?
(a)Chills(b)Chaplets(c)Cores(d)None of the above
225. In the casting process what name is given to the part which is used torepresent the finished item?
(a)The mould(b)The spruce(c)The pattern(d)The shell
226. The crystal structure of a casting adjacent to the mould wall will be?
(a)Fine equiaxed grains(b)Core equiaxed grains(c)Columnar grains(d)Dendritic
189. Beryllium base
190. Aluminum191. All of the above192. Re-crystallization193. ET194. Copper195. Copper and zinc196. Radiography and penetrant197. Galvanizing198. Will char when heated199. Charred by heat200. Beryllium base201. Beryllium
202. Notch sensitivity203. Zinc204. Permanent magnets205. Shape changing206. All of the above207. Casting208. All of the above209. All of the above
-
8/11/2019 E.M.C Sample Question
32/38
210. All of the above211. Solid state of casting212. Large radii213. Gating system214. Shrinkage215. Chills216. Core217. Clay and water218. A cope219. Chaplets220. Investment casting221. Centrifugal casting222. Cold shut223. Drag224. Chills225. The pattern226. Fine equiaxed grains
227. Which of the following is required - in theory - for two perfectlymatched faces?
(a)Atomic cleanliness(b)Atomic closeness(c)Pressure
(d)Both a and c are correct
228. Fusion bonding creates a metallurgical effect similar to?
(a)Rolling(b)Forging(c)Casting(d)Sintering
229. The bonding process giving very high efficiency is?
(a)Fusion bonding(b)Pressure bonding(c)Flow bonding(d)Atomic bonding
-
8/11/2019 E.M.C Sample Question
33/38
230. A bonding process where only very small amounts of the base metal isused is called?
(a)Fusion bonding(b)Pressure bonding(c)Flow bonding(d)Cold bonding
231. Flow bonding is a particular type of bond, which listed below would beclassed as a flow bond?
(a)Fusion welding(b)Braze welding(c)Metal arc welding(d)None of the above
232. Which of these defects can be found in fusion welds?
(a)Porosity(b)Slag(c)Cracks(d)All of the above
233. The portion of the base metal affected by the welding process isknown as?
(a)The weld zone
(b)The heat input zone(c)The weld affect zone(d)The heat affected zone
234. Multiple cooling rates can have adverse affects on weld areas. Whatcan be done to offset this problem?
(a)Use different alloy rods to control temperature(b)Using a pre-heat(c)Use different alloy rods to control temperature and using a pre-heat(d)Nothing can be done to offset the problem
235. Angular distortion may occur in a weld when?
(a)Restraints are used(b)Multipass welds are used(c)Single pass welds are used(d)Multiple welds and single pass welds are used
-
8/11/2019 E.M.C Sample Question
34/38
236. Longitudinal stresses in a weld are at a maximum?
(a)Along the weld centre line(b)On the weld fusion face(c)At the heat affected zone(d)Longitudinal stresses are uniform across the weld
237. What is required to form a fusion bond?
(a)Melting of parent metals(b)A filler rod(c)Pressure(d)All of the above
238. Flow bonding is a term used in the welding process which of thefollowing would be classed as flow bonding?
(a)Brazing(b)Braze welding(c)Soldering(d)All of the above
239. In forgings the grain?
(a)Follows the shape of the dies(b)Becomes coarser(c)Retains its original shape(d)Both a and b are correct
240. In order to produce a fully homogenous material after welding whichof the following is required?
(a)Preheat(b)Post heat treatment(c)Low heat input welding(d)Fillers of different composition
241. In electric arc welding, a metal rod is one electrode, the other is?
(a)The work material
(b)The rod flux(c)The earth(d)The work material and the rod flux
-
8/11/2019 E.M.C Sample Question
35/38
242. Stud welding is used primarily to?
(a)Bond two dissimilar metals(b)Attach threaded fasteners to plates(c)Rivet plates together(d)Fuse bar ends together
243. A welding electrode coatings provides?
(a)A shield for the arc against the atmosphere(b)Added heat input(c)Additional stresses to the weld(d)None of the above
244. Where gas is used as a shield for the welding process the gas iscommonly?
(a)Argon(b)Helium(c)Hydrogen(d)Argon and Helium
245. When using gas metal arc welding what range of filler wire diameteris available?
(a) 0.1-0.5mm(b) 0.5-30mm(c) 0.1-30mm
(d) 0.5-10mm
246. Automatic welding under a flux is more commonly known as?
(a)TIG welding(b)Manual metal arc welding(c)Submerged arc welding(d)Stick welding
247. Spot welding is commonly used in which of the followingapplications?
(a)Car manufacturing(b)Seam welding(c)Shipbuilding(d)Fabrication yards
-
8/11/2019 E.M.C Sample Question
36/38
248. Which welding process takes place in a vacuum?
(a)Plasma arc welding(b)Electron beam welding(c)Friction welding(d)Explosion welding
249. Which welding process is generally used to weld the ends of heavyround bars or tubes?
(a)Ultrasonic welding(b)Electro slag welding(c)Plasma arc welding
(d)Friction welding
250. Explosion welding is generally used to join?
(a)Two or more metals of different composition(b)Butt welds(c)Very think titanium sheeting(d)Plastics
251. AWS categorize weld defects into three classes which below is adimensional defect?
(a)Slag(b)Warping(c)Lack of fusion
(d)Porosity
252. Which of the following is classed as a structural defect?
(a)Undercut(b)Slag(c)Incomplete fusion(d)All of the above
253. Welds without preheat are said to have?
(a)Very low thermal gradients(b)Low thermal gradients(c)Medium thermal gradients(d) High thermal gradients
-
8/11/2019 E.M.C Sample Question
37/38
254. Why is it advisable to leave the final inspection of a weld until well
after the welding has finished?
(a)Because the welds will be too hot to test(b)Due to the possibility of distortion(c)Due to the possibility of post weld cracking(d)All of the above
255. What is the approximate arc column temperature in an electric arcweld?
(a)6000 degrees Celsius(b)5000 degrees Celsius(c)4000 degrees Celsius(d)3000 degrees Celsius
256. Which of the following is classified as an inert gas?
(a)Hydrogen(b)Helium(c)Oxygen(d)All of the above
257. Which weld process has a non-consumable electrode?
(a)Manual metal arc(b)Metal inert gas
(c)Tungsten inert gas(d)Manual metal arc and metal inert gas
258. Which of the following processes could be performed usingoxyacetylene equipment?
(a)Flame cutting(b)Brazing(c)Soldering(d)All of the above
259. How might a weld arc be shielded from oxidation?
(a)Flux powders(b)Welding rod coatings(c)Inert gases(d)All of the above
-
8/11/2019 E.M.C Sample Question
38/38
227. Atomic cleanliness and atomic pressure228. Casting229. Pressure bonding230. Flow bonding231. Braze welding232. All of the above233. The heat affected zone234. Using a pre-heat235. Multiple welds and single pass welds are used236. Along the weld centre line237. Melting of parent metals238. All of the above239. The answer is : A240. Post heat treatment
241. The work material242. Attach threaded fasteners to plates243. A shield for the arc against the atmosphere244. Argon and Helium245. 0.5-3mm246. Submerged arc welding247. Car manufacturing248. Electron beam welding249. Friction welding250. Two or more metals of different composition251. Warping
252. All of the above253. High thermal gradients254. All of the above255. 6000 degrees Celsius256. Helium257. Tungsten inert gas258. All of the above259. All of the above