electronic ballast - lumiaction - supplier and …lumibulb.com/catalog/images/p46-p78 electronic...

【46】

Electronic Ballast

Electronic Ballast Economical Electronic Ballasts : For small tube diameter and high tube voltage, T5 Fluorescent Lamps have to be driven by a really compatible electronic ballast which would get advantage to achieve energy saving. In another word, the compatible electronic ballast must comply with EMC and necessary protection function for abnormal conditions to ensure the safety. Standard electronic Ballasts : Cut-Off technology Before the lamp is really ignited, to warm up the cathode is an advantageous process of preheating. That helps the electronic powder to not be over-sputtered when light being started. That would also prevent excessively turning black at the end of tube and can extend lamp life through increasing tunes if starting cycles. The filament warm up current sometimes can not be completely cut off after lamps started. As a result, the filament load is increased. The CUT-OFF technology can efficiently reduce filament load more than 20%, extend the lamp life. It also improves lumen of fluorescent lamp and efficiency of lighting.

Professional Electronic Ballasts : Electronic ballast of constant power, within the range of rated supply voltage, can ensure the constant output characteristics, maintain steady brightness and ensure the continuity and stability of lighting. Multi-power electronic ballast refers to that one type of electronic ballast can automatically fit tubes of different power. For various kinds of luminaries nowadays, that is a technical change to “one for one” electronic ballast. The professional ballast adopts professional integrated circuit to automatically adjust output parameters and ensure the nominal luminaries operated in the best state. The fool type brings convenience for customers from difficult choosing in multi types of ballast. At the same time, customers can save much cost on purchase, logistics, equipments as well as stock. This product is especially suitable for the place replacing luminaries frequently, such as light manufacturer and conditions for testing different lights. This professional electronic ballast, a multi-power product of programmed preheating, cut-off, EOL and constant output power, whose designed life can reach over 50,000 hours, is suitable for high-end customers.

End of Life : The electronic ballasts have protection circuit for abnormal operating conditions, when lamps do not start or completely rectification effect occurs, the inner protection circuit of ballast can automatically turn into a state of protection. But in the event of “end of life effect”. Most ballast do not have such protection. The EOL technology has avoided any security failures of lights and ballasts. In practical application, the end of a lamp results from that electron emission from one cathode is deficient while another one is still in order, which leads that electric arc is often inconsistent in successive semi cycle. Tubes need a continual higher voltage to be lit up, thus cause lamp flicker and flicker. At the same time, the super-energy of power output of electronic ballasts mostly takes effect on tubes, on account of that this energy focuses on the cathode of small volume – especially for the tube T5 of smaller diameter. So that filament and funnel-shaped glass burn out, temperature rise of lamp going up leads lamp holder intenerating. What’s worse, the glass wall of lamp would suddenly heat and crack. The above phenomenon is likely to make tube fall off and injure persons. Pre-Heating Technology : In the process of lamp starting, that precise controlling technology for tube voltage and filament current, provides appropriate starting energy for lamps. After a certain period of ignition, lamps can not discharge by the reason of no electron emission on cathode. Concretely speaking, that is caused by lamps of end of life, the electronic power has almost used up, therefore lamp life is short because the electronic power consumes quickly, and the consumption of electronic power is cue to positive ion sputtering in the process of lamp starting. Before modern electronic ballasts starting lamps, electronic power from cathode suffers differently sputtering with different pre-heating technology. By testing, a large number of electronic ballasts have consumed the electronic power from cathode after switching 6,000 times. However, the programmed preheating technology will not damage the cathode even switching 20,000 times, what’s more, the electronic ballasts for railway and bus can switch 30,000 times. Through precise frequency control and module control, could preheat filament completely, impact on filament in the process of starting can be reduced and preheating energy completely comply with IEC60929 and lamp life has significantly extended.

【47】

Save Energy and Money, More Efficient and More Reliable : Compared to traditional ballasts, in addition to having all the functions of magnetic ballasts, the electronic ballasts have more outstanding characteristics. Low power consumption, increasing light output and improving light efficiency. Under a frequency of 50Hz/60Hz on AC, light impedance has been changing constantly in the cycle of AC supply, resulting in non-sine voltage, current wave from and harmonics. When using electronic ballast, the ionized state in the lamp will not change rapidly with the lamp current, thus almost constant plasma density and light impedance are formed in the entire cycle. The light efficiency of fluorescent lamp driven by electronic ballast, is 10%~20% better compared with magnetic ballast. The power factor of magnetic ballast is only 0.5~0.6, while that of electronic ballast can reach 0.98, and professional series even reach 0.99 Can be easily started, having good start function, no flicker and repeated starting, which extends lamp life.

Dimmable Electronic Ballasts Undertaking the reliable and stable quality of non-dimming electronic ballast, the series of this dimmable electronic ballast designed according to IEC61347-1, IEC61347-2-3, EN60929, IEC61000-3-2, EN55015, EN61547, not only integrate programmed preheating, EOL protection, Cut-off technology, lamps adoption function and etc., but also have features of comfortable light and controllability.

Electronic Ballast in Multiple Unit Train, Bus and Boats : The rail transportation of urban in the future will consist of “metro+light rail+MU train of suburb”, forming a three-dimensional traffic network from inside to outside, diffluenting layer upon layer. That population and MU at suburb. The merits of this network are : the crowd time and can deal with uncertain flow; fast MU can greatly short travel time to remote outskirts. MU can run in small groups of high density, with advantages of good safety performance, large capacity, less pollution, energy saving, needs not change head out and home and has its own power, which enjoys a favor home and abroad and takes prise of “the new darling” of transportation at 21st century.

Emergency Lighting Controllers Applied for fluorescent luminaries, such as, grille lamp, frame lights, ceiling lamps, tri-proof light and etc., which is the best choice of emergency lighting in public. When the normal lighting stop working, emergency lighting is provided for substitute. Common Malfunctions and Disposal Methods of Electronic Ballasts Ballasts are installed in fixtures to drive the lamps, and should be in the state of power-off while obviating malfunctions or replacing lamps. Malfunction : rolling light in lamps Reason and disposal method : it is normal phenomenon which usually happens when the environment or lamps temperature are lower, and it can be obviated after lamps working for a longer time. Malfunction : bright in both ends but dark in the middle of tube Reason and disposal method : it is normal phenomenon which usually happens when the environment or lamps temperature are lower, and it can be obviated after lamps working for a longer time. Malfunction : glare in lamps Reason and disposal method: that is for the lamps having not been aged completely before leaving the factory. At this time, we should switch on and off several times to activate lamp completely. If glare still remains, the lamps should be replaced immediately, or electronic ballasts will be damaged Malfunction : lamps not working at all Disposal method : please take the five steps as follows, 1. Power off 2. Replace lamp -> if still no working 3. waiting for 2 minutes and then re-connect power on 4. Check to make sure that every contact between

lamps and socket are not loosing off 5. If those are, re-set those contacts 6. Check whether the connection between ballast and

lamps socket are correctly mounted 7. If neither above disposals are not workable, replace

ballast is recommended

【48】

Malfunction : large numbers of lamps not working Reason and disposal method : Examine fixture input power in installation site carefully. 1. Stability of supply voltage : examining whether

temporary power is supplied to lights. And whether high-power construction equipment – such as electric welder, cutting machine, motor etc are loaded in the same lighting wire. If the temporary power is supplied in the construction sites without surge voltage protector, higher instant surge current produce by high-power equipments would damage the electronic ballasts.

2. Checking supply voltage’s normally (power distribution) : measuring the supply voltage and examining the connecting wires of switchboard. Lighting electricity shares one phase from dynamic electricity, when the neutral line (zero line) invalidly, one of three phases power loads much larger than the other two, which resulting in an imbalance phase and the lighting power voltage power voltage up to 380V, thus damaged the ballast.

3. Checking whether the lights are grounded reliably : testing the surface of ballast shells by electrical pen whether it has electricity on that, if not grounded reliably, the interference signal would lead to ballasts working abnormally and bring safety problem for human.

Caution for installation and Operation of Electronic Ballasts ＊ The wiring ways of input and output include terminals

and wires, and the wires should be chosen according to wire diameter range printed on the electronic ballasts labels, which should be of safety marking.

＊ Lamp should be chosen according to lamp type and number indicated on electronic ballast label.

＊ Wires should be connected correctly in the light of wiring diagram of electronic ballast label.

＊ For the view of safety, the electronic ballasts should be earthed reliably.

＊ On taking dielectric strength test in lights assembly plants, that should be done from output side to input side in order to avoid damaging the electronic ballasts for output lines and lights short circuited.

＊ In the lights fabricating yard, lights power line and large scale equipments – electric welder, motor etc should abstain to share one power line, otherwise the higher instant surge current produced by on/off of large scale equipments would damage the electronic ballasts.

＊ When using electronic dimming ballasts, the new lamps in advised to operate at least 100 hours under the condition of 100% light output.

＊ The warranty is not applicable to any electronic ballast which has not been installed and operated in accordance with its specifications and connection diagrams.

【49】

Electronic Ballast

Economic Electronic Ballasts for T5 Fluorescent Lamps Introduction & Wire Diagram :

General information about Economic Electronic Ballasts for T5 Fluorescent Lamps : Rated voltage : AC 220-240V 50/60Hz Starting type : Pre-heat Power Factor 0.98 THD <15% Crest Factor <1.7 Applying to 1 lamp or 2 lamps 1x14W – 1x21W – 1x28W – 1x35W - 2x14W – 2x21W – 2x28W – 2x35W - 3x14W – 3x24W Material : Metal

Dim. L (mm) W (mm) H (mm) Mounting distance

A 251 30 27 239.5mm

B 288 30 27 276.5mm

C 360 30 27 348.5mm

【WIRE DIAGRAM】

1 x 1

1 x 2

Model No. Lamp Type Rated Voltage Line Current

Power Factor

THD Crest Factor Dim.

LMBLS-001 1 x 14W AC220-240V 0.070A 0.98 <15% <1.7 A

LMBLS-002 1 x 21W AC220-240V 0.110A 0.98 <15% <1.7 A

LMBLS-003 1 x 28W AC220-240V 0.140A 0.98 <15% <1.7 A

LMBLS-004 2 x 14W AC220-240V 0.140A 0.98 <15% <1.7 B

LMBLS-005 2 x 21W AC220-240V 0.220A 0.98 <15% <1.7 B

LMBLS-006 2 x 28W AC220-240V 0.270A 0.98 <15% <1.7 B

LMBLS-007 3 x 14W AC220-240V 0.210A 0.98 <15% <1.7 C

LMBLS-008 3 x 24W AC220-240V 0.340A 0.98 <15% <1.7 C

【50】

Electronic Ballast

Standard Electronic Ballasts for T5 Fluorescent Lamps Introduction & Wire Diagram :

General information about Standard Electronic Ballasts for T5 Fluorescent Lamps : Rated voltage : AC 220-240V 50/60Hz Starting type : Pre-heat Power Factor 0.98 THD <10% Crest Factor <1.7 Applying to drive 1 lamp, 2 lamps or 3 lamps 1x24W - 1x39W – 1x49W - 1x54W – 2x24W - 2x39W – 2x49W – 2x54W - 3x24W – 3x39W Material : Metal


A 288 30 27 376.5mm

B 360 30 27 348.5mm

C 280 30 21 268.5mm

【WIRE DIAGRAM】

1 x 1

1 x 2

1 x 3

【51】


Power Factor THD Crest

Factor Dim.

LMBLS-009 1 x 14W AC220-240V 0.075A 0.98 <10% <1.7 A

LMBLS-010 1 x 21W AC220-240V 0.110A 0.98 <10% <1.7 A

LMBLS-011 1 x 24W AC220-240V 0.110A 0.98 <10% <1.7 A

LMBLS-012 1 x 28W AC220-240V 0.140A 0.98 <10% <1.7 A

LMBLS-013 1 x 35W AC220-240V 0.170A 0.98 <10% <1.7 A

LMBLS-014 1 x 39W AC220-240V 0.185A 0.98 <10% <1.7 A

LMBLS-015 1 x 49W AC220-240V 0.260A 0.98 <15% <1.7 A

LMBLS-016 1 x 54W AC220-240V 0.230A 0.98 <10% <1.7 A

LMBLS-017 2 x 14W AC220-240V 0.140A 0.98 <10% <1.7 A

LMBLS-018 2 x 21W AC220-240V 0.210A 0.98 <10% <1.7 A

LMBLS-019 2 x 24W AC220-240V 0.220A 0.98 <10% <1.7 A

LMBLS-020 2 x 28W AC220-240V 0.270A 0.98 <10% <1.7 A

LMBLS-021 2 x 35W AC220-240V 0.330A 0.98 <10% <1.7 A

LMBLS-022 3 x 14W AC220-240V 0.210A 0.98 <10% <1.7 B

LMBLS-023 3 x 24W AC220-240V 0.340A 0.98 <15% <1.7 B

LMBLS-024 1 x 14W AC220-240V 0.075A 0.98 <10% <1.7 C

LMBLS-025 1 x 21W AC220-240V 0.110A 0.98 <10% <1.7 C

LMBLS-026 1 x 28W AC220-240V 0.140A 0.98 <10% <1.7 C

LMBLS-027 1 x 35W AC220-240V 0.170A 0.98 <10% <1.7 C

【52】

Electronic Ballast


General information about Standard Electronic Ballasts for T5 Fluorescent Lamps : Rated voltage : AC 220-240V 50/60Hz Starting type : Pre-heat Power Factor 0.98 THD <10% Crest Factor <1.7 Applying to drive 1 lamp, 2 lamps or 3 lamps 1x24W - 1x39W – 1x49W - 1x54W – 2x24W - 2x39W – 2x49W – 2x54W - 3x24W – 3x39W Material : Metal


A 362 30 27 349.5mm

B 386 30 27 373m

C 448 30 29.5 435mm

【WIRE DIAGRAM】

1 x 1

1 x 2

1 x 3

【53】



Factor Dim.

LMBLS-028 1 x 14W AC220-240V 0.070A 0.98 <15% <1.7 A

LMBLS-029 1 x 21W AC220-240V 0.100A 0.98 <15% <1.7 A

LMBLS-030 1 x 24W AC220-240V 0.110A 0.97 <15% <1.7 A

LMBLS-031 1 x 28W AC220-240V 0.140A 0.98 <15% <1.7 A

LMBLS-032 1 x 35W AC220-240V 0.180A 0.98 <15% <1.7 A

LMBLS-033 1 x 49W AC220-240V 0.260A 0.98 <15% <1.7 B

LMBLS-034 2 x 14W AC220-240V 0.135A 0.98 <15% <1.7 A

LMBLS-035 2 x 21W AC220-240V 0.210A 0.98 <15% <1.7 A

LMBLS-036 2 x 24W AC220-240V 0.220A 0.98 <15% <1.7 A

LMBLS-037 2 x 28W AC220-240V 0.260A 0.98 <15% <1.7 B

LMBLS-038 2 x 35W AC220-240V 0.340A 0.98 <15% <1.7 B

LMBLS-039 2 x 39W AC220-240V 0.350A 0.98 <15% <1.7 B

LMBLS-040 2 x 49W AC220-240V 0.450A 0.98 <15% <1.7 B

LMBLS-041 2 x 54W AC220-240V 0.480A 0.98 <15% <1.7 B

LMBLS-042 3 x 14W AC220-240V 0.210A 0.98 <15% <1.7 C

LMBLS-043 3 x 24W AC220-240V 0.320A 0.98 <15% <1.7 C

LMBLS-044 3 x 28W AC220-240V 0.420A 0.98 <15% <1.7 C

LMBLS-045 3 x 39W AC220-240V 0.520A 0.98 <15% <1.7 C

【54】

Electronic Ballast

Economic Electronic Ballasts for T8 Fluorescent Lamps Introduction & Wire Diagram :

General information about Economic Electronic Ballasts for T8 Fluorescent Lamps : Rated voltage : AC 220-240V 50/60Hz Starting type : Pre-heat or Instant Power Factor 0.98 THD <15% for 1x1 & 1x2 ; THD <20% for 1x3 Crest Factor <1.7 After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of

emergency, low total harmonic distortion and high power factor. Comply with IEC60929, IEC61347-1, IEC61347-2-3, IEC61000-3-2, EN55015, EN61547 Applying to 1 lamp, 2 lamps or 3 lamps 1x18W – 1x30W - 1x36W – 2x18W – 2x30W - 2x36W – 3x18W - 3x30W – 3x36W Material : Metal


A 221 37 30 209mm

B 271 40 30 259mm

C 350 44 34 338mm

【WIRE DIAGRAM】

1 x 1

1 x 2

1 x 3



Factor Dim.

LMBLS-046 1 x 18W AC220-240V 0.080A 0.98 <15% <1.7 A

LMBLS-047 1 x 36W AC220-240V 0.160A 0.98 <15% <1.7 A

LMBLS-048 2 x 18W AC220-240V 0.160A 0.98 <15% <1.7 B

LMBLS-049 2 x 36W AC220-240V 0.320A 0.98 <15% <1.7 B

LMBLS-050 3 x 18W AC220-240V 0.240A 0.98 <20% <1.7 C

LMBLS-051 3 x 36W AC220-240V 0.500A 0.98 <20% <1.7 C

【55】

Electronic Ballast


General information about Standard Electronic Ballasts for T8 Fluorescent Lamps : Rated voltage : AC 220-240V 50/60Hz Starting type : Pre-heat or Instant Power Factor 0.98 THD <15% or <20% Crest Factor <1.7 After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of

emergency, low total harmonic distortion and high power factor. Comply with IEC60929, IEC61347-1, IEC61347-2-3, IEC61000-3-2, EN55015, EN61547 Meet with EMC directive Applying to 1 lamp, 2 lamps, 3 lamps or 4 lamps 1x18W – 1x30W - 1x36W - 1x58W – 2x18W – 2x30W - 2x36W – 2x56W – 3x18W - 3x36W – 4x18W Material : Metal

【WIRE DIAGRAM】

1 x 1

1 x 2

1 x 3

【56】


A 251 30 27 239.5mm

B 288 30 27 276.5mm

C 360 30 27 348.5mm


A 266 42 30 251mm

B 343 42 30 328mm

C 394 29.5 27 373mm

D 394 43 34 379mm



Factor Dim.

LMBLS-052 1 x 18W AC220-240V 0.080A 0.98 <10% <1.7 A

LMBLS-053 1 x 30W AC220-240V 0.130A 0.98 <10% <1.7 A

LMBLS-054 1 x 36W AC220-240V 0.160A 0.98 <10% <1.7 A

LMBLS-055 1 x 58W AC220-240V 0.255A 0.98 <15% <1.7 A

LMBLS-056 2 x 18W AC220-240V 0.160A 0.98 <10% <1.7 B

LMBLS-057 2 x 30W AC220-240V 0.270A 0.98 <10% <1.7 B

LMBLS-058 2 x 36W AC220-240V 0.320A 0.98 <10% <1.7 B

LMBLS-059 3 x 18W AC220-240V 0.240A 0.98 <10% <1.7 C

LMBLS-060 3 x 36W AC220-240V 0.480A 0.98 <15% <1.7 C

LMBLS-061 4 x 18W AC220-240V 0.320A 0.98 <20% <1.7 C



Factor Dim.

LMBLS-062 1 x 18W AC220-240V 0.080A 0.98 <10% <1.7 A

LMBLS-063 1 x 30W AC220-240V 0.130A 0.98 <10% <1.7 A

LMBLS-064 1 x 36W AC220-240V 0.160A 0.98 <10% <1.7 A

LMBLS-065 1 x 58W AC220-240V 0.255A 0.98 <15% <1.7 A

LMBLS-066 2 x 18W AC220-240V 0.160A 0.98 <15% <1.7 B

LMBLS-067 2 x 30W AC220-240V 0.270A 0.98 <10% <1.7 B

LMBLS-068 2 x 36W AC220-240V 0.320A 0.98 <10% <1.7 B

LMBLS-069 2 x 58W AC220-240V 0.510A 0.98 <15% <1.7 C

LMBLS-070 3 x 18W AC220-240V 0.240A 0.98 <15% <1.7 D

LMBLS-071 3 x 36W AC220-240V 0.480A 0.98 <15% <1.7 D

LMBLS-072 4 x 18W AC220-240V 0.320A 0.98 <20% <1.7 D

【57】

Electronic Ballast

Professional Electronic Ballasts for T5/T8 Fluorescent Lamps Introduction & Wire Diagram :

General information about Professional Electronic Ballasts for T5/T8 Fluorescent Lamps : Rated voltage : AC120-277V & AC 220-240V 50/60Hz Starting type : Pre-heat or Instant Power Factor 0.98 Crest Factor <1.5 After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of

emergency, low total harmonic distortion and high power factor. Comply with IEC61347-1, IEC61347-2-3, IEC61000-3-2, EN55015, EN61547 Meet with EMC directive Applying to 1 lamp or 2 lamps 1x18W – 1x36W - 1x58W – 2x18W – 2x36W – 2x58W – 1x17,25,32W – 2x17,25,32W Material : Metal


A 280 30 21 268.5mm

B 359 30 21 347.5mm

C 359 30 27 347.5mm

D 360 30 26 346mm

【WIRE DIAGRAM】

1 x 1

1 x 2

【58】

Model No. Lamp Type Rated Voltage

Voltage Range

Power Factor

Crest Factor Dim.

LMBLS-073 1 x 18,36W AC220-240V 0.98 <1.5 A

LMBLS-074 1 x 58W AC220-240V 0.98 <1.5 A

LMBLS-075 1 x HF32W AC220-240V 0.98 <1.5 A

LMBLS-076 2 x 18,36W AC220-240V 0.98 <1.5 B

LMBLS-077 2 x 58W AC220-240V 0.98 <1.5 C

LMBLS-078 2 x HF32W AC220-240V

AC187-253V

0.98 <1.5 C

1 x 17,25,32W D LMBLS-079

2 x 17,25,32W AC120-277V 0.98 <1.5

D

1 x 18W,36W D LMBLS-080

2 x 18W,36W AC120-277V 0.98 <1.5

D

1 x 58W D LMBLS-081

2 x 58W AC120-277V

AC100-300V

0.98 <1.5 D

【59】

Electronic Ballast

Electronic Ballasts with pig-tail for T8 Fluorescent Lamps

Introduction & Wire Diagram :

General information about Electronic Ballasts with pig-tail for T8 Fluorescent Lamps : Rated voltage : AC 220-240V 50/60Hz Starting type : Pre-heat or Instant Power Factor 0.98 THD <15% Crest Factor <1.7 After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of

emergency, moisture proof and anti-vibration. potted and sealed structure. Comply with IEC60929, IEC61347-1, IEC61347-2-3, IEC61000-3-2, EN55015, EN61547 Meet with EMC directive Applying to 1 lamp or 2 lamps 1x18W – 1x30W – 1x36W - 2x18W – 2x30W – 2x36W Material : Metal


A 241 43 30 226mm

【WIRE DIAGRAM】

1 x 1

1 x 2



Factor Dim.

LMBLS-082 1 x 18W AC220-240V 0.085A 0.96 <15% <1.7 A

LMBLS-083 1 x 30W AC220-240V 0.140A 0.96 <15% <1.7 A

LMBLS-084 1 x 36W AC220-240V 0.170A 0.96 <15% <1.7 A

LMBLS-085 2 x 18W AC220-240V 0.170A 0.96 <15% <1.7 A

LMBLS-086 2 x 30W AC220-240V 0.280A 0.96 <15% <1.7 A

LMBLS-087 2 x 36W AC220-240V 0.340A 0.96 <15% <1.7 A

【60】

Electronic Ballast

Electronic Ballasts with pig-tail for T8 Fluorescent Lamps Introduction & Wire Diagram :

General information about Electronic Ballasts with pig-tail for T8 Fluorescent Lamps : Rated voltage : AC 220-240V 50/60Hz Starting type : Pre-heat or Instant Power Factor 0.98 THD <15% or <10% Crest Factor <1.7 After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of

emergency, moisture proof and anti-vibration. potted and sealed structure. Comply with IEC60929, IEC61347-1, IEC61347-2-3, IEC61000-3-2, EN55015, EN61547 Meet with EMC directive Applying to 1 lamp or 2 lamps 1x18W – 1x30W – 1x36W – 1x58W - 2x18W – 2x30W – 2x36W Material : Metal


B 260 40 29 240mm

C 335 40 29 320mm

【WIRE DIAGRAM】

1 x 1

1 x 2



Factor Dim.

LMBLS-088 1 x 18W AC220-240V 0.085A 0.98 <10% <1.7 B

LMBLS-089 1 x 30W AC220-240V 0.145A 0.98 <10% <1.7 B

LMBLS-090 1 x 36W AC220-240V 0.165A 0.98 <10% <1.7 B

LMBLS-091 1 x 58W AC220-240V 0.265A 0.98 <15% <1.7 B

LMBLS-092 2 x 18W AC220-240V 0.165A 0.98 <10% <1.7 C

LMBLS-093 2 x 30W AC220-240V 0.275A 0.98 <10% <1.7 C

LMBLS-094 2 x 36W AC220-240V 0.330A 0.98 <10% <1.7 C

【61】

Electronic Ballast

Electronic Ballasts for T5/T8 Circular Fluorescent Lamps Introduction & Wire Diagram :

General information about Electronic Ballasts for T5/T8 Circular Fluorescent Lamps : Rated voltage : AC 220-240V 50/60Hz Voltage range : 187-253V 50/60Hz Starting type : Pre-heat Power Factor 0.98 THD <15% Crest Factor <1.7 After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of emergency. Comply with IEC60929, IEC61347-1, IEC61347-2-3, IEC61000-3-2, EN55015, EN61547 Meet with EMC directive Applying to Circular Fluorescent Lamps 22W – 32W – 40W Material : Metal


A 105 53 28.5 95mm

【WIRE DIAGRAM】



Factor Dim.

LMBLS-095 1 x 22W AC220-240V 0.100A 0.98 <15% <1.7 A

LMBLS-096 1 x 32W AC220-240V 0.150A 0.98 <15% <1.7 A

LMBLS-097 1 x 40W AC220-240V 0.185A 0.98 <15% <1.7 A

【62】

Electronic Ballast

Electronic Ballasts for PL Energy Saving Lamps & 2D lamps Introduction & Wire Diagram :

General information about Electronic Ballasts for PL Energy Saving Lamps & 2D Lamps : Rated voltage : AC 220-240V 50/60Hz Voltage range : 187-253V 50/60Hz Starting type : Pre-heat Power Factor 0.98 THD <15% Crest Factor <1.7 After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of

emergency. Comply with IEC60929, IEC61347-1, IEC61347-2-3, IEC61000-3-2, EN55015, EN61547 Meet with EMC directive Applying to 1 lamp or 2 lamps 1x11W – 1x13W – 1x18W – 1x26W – 1x32W – 1x42W – 2x11W – 2x13W – 2x18W – 2x26W –

2x32W – 2x42W – 1x21W 2D – 1x28W 2D – 1x38W 2D Material : Plastic


A 102.5 66.5 29.5 M1= 108.9mm M2=88.3mm

B 123.2 79 33.2 M1= 130.3mm M2=99.3mm

【WIRE DIAGRAM】

1 x 1

1 x 2

2D Lamp

【63】



Factor Dim.

LMBLS-098 1 x 11W PL-S,TC AC220-240V 0.050A 0.96 <15% <1.7 A

LMBLS-099 2 x 11W PL-S,TC AC220-240V 0.100A 0.96 <15% <1.7 B

LMBLS-100 1 x 13W PL-C,TC-D AC220-240V 0.060A 0.97 <15% <1.7 A

LMBLS-101 2 x 13W PL-C,TC-D AC220-240V 0.120A 0.98 <15% <1.7 B





LMBLS-106 1 x 32W PL-T,TC-T AC220-240V 0.140A 0.98 <15% <1.7 A

LMBLS-107 2 x 32W PL-T,TC-T AC220-240V 0.280A 0.98 <15% <1.7 B

LMBLS-108 1 x 42W PL-T,TC-T AC220-240V 0.185A 0.98 <15% <1.7 A

LMBLS-109 2 x 42W PL-T,TC-T AC220-240V 0.370A 0.98 <15% <1.7 B

LMBLS-110 1 x 26,32,42W PL-C/PL-T, TC-D/TC-T

AC220-240V 0.09-0.21A 0.98 <10% <1.7 A

LMBLS-111 2 x 26,32,42W PL-C/PL-T, TC-D/TC-T

AC220-240V 0.18-0.42A 0.98 <10% <1.7 B

LMBLS-112 1 x 21W PL-Q,TC-DD2D

AC220-240V 0.095A 0.98 <15% <1.7 A


AC220-240V 0.125A 0.98 <15% <1.7 A


AC220-240V 0.170A 0.98 <15% <1.7 A

【64】

Electronic Ballast

Electronic Dimmable Ballasts for T5/T8 Linear Fluorescent Lamps Introduction & Wire Diagram :

General information about Electronic Dimmable Ballasts for T5/T8 Linear Fluorescent Lamps : Rated voltage : AC 220-240V 50/60Hz Voltage range : 187-253V 50/60Hz Starting type : Pre-heat Power Factor 0.98 THD <15% Crest Factor <1.7 Input control : DC 1-10V 0.5mA Dimming range : 1%~100% for T8 ; 3%~100% for T5 After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of emergency. Comply with IEC60929, IEC61347-1, IEC61347-2-3, IEC61000-3-2, EN55015, EN61547 Meet with EMC directive Applying to 1 lamp or 2 lamps 1x18W – 1x30W – 1x36W T8 ; 1x14W – 1x21W – 1x28W – 1x35W T5 ; 1x54W T5 & 1x58W T8 ;

2x18W – 2x30W – 2x36W T8 ; 2x18W – 2x24W – 2x36W – 2x40W - 2x14W – 2x21W – 2x28W – 2x35W T5 ; 2x49W - 2x54W T5 & 2x58W T8

Material : Metal

Dim L (mm) W (mm) H (mm) Mounting distance

A 360 30 26 346mm

【WIRE DIAGRAM】

1 x 1

1 x 2

【65】



Factor Dim.

LMBLS-115 1 x 18,30, 36W AC220-240V 0.078 -0.156A

0.98 <15% <1.5 A

LMBLS-116 1 x 14,21,28,35W AC220-240V 0.074 -0.170A

0.98 <15% <1.5 A

LMBLS-117 1 x 49W AC220-240V 0.230A 0.98 <15% <1.5 A

LMBLS-118 1 x 54W, 59W AC220-240V 0.250A 0.98 <15% <1.5 A

LMBLS-119 2 x 18,30,36W AC220-240V 0.150 -0.315A

0.98 <15% <1.5 B

LMBLS-120 2 x 14,21,28,35W AC220-240V 0.140 -0.340A

0.98 <15% <1.5 B

LMBLS-121 2 x 49W AC220-240V 0.440A 0.98 <15% <1.5 C

LMBLS-122 2 x 58W AC220-240V 0.490A 0.98 <15% <1.5 C

【66】

Electronic Ballast

Electronic Dimmable Ballasts for Compact Fluorescent Lamps Introduction & Wire Diagram :

General information about Electronic Dimmable Ballasts for Compact Fluorescent Lamps : Rated voltage : AC220-240V Voltage range : 187-253V 50/60Hz Starting type : Pre-heat Power Factor 0.98 THD <15% Crest Factor <1.5 Input control : DC 1-10V 0.5mA Dimming range : 3%~100% for TC-D, TC-T Lamps ; 5%~100% for TC-L Lamps After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of emergency and EOL. Comply with IEC60929, IEC61347-1, IEC61347-2-3, IEC61000-3-2, EN55015, EN61547 Meet with EMC directive Applying to 1 lamp or 2 lamps 1x18W – 1x26W - 1x32W – 1x42W PL Lamps ; 2x18W – 2x26W – 2x32W – 2x42W TC Lamps Material : Plastic


A 123.2 79 33.2 M1=130.3mm M2=99.3mm

【WIRE DIAGRAM】

1 x 1

1 x 2


Line Current


Factor Dim.

LMBLS-123 1 x 18W AC220-240V 0.090A 0.98 <15% <1.5 A

LMBLS-124 1 x 26,32,42W PL-C/PL-T AC220-240V 0.130-0.200A 0.98 <15% <1.5 A

LMBLS-125 2 x 18W TC-D/TC-T AC220-240V 0.160A 0.98 <15% <1.5 A

LMBLS-126 2 x 26,32,42W AC220-240V 0.246-0.390A 0.98 <15% <1.5 A

【67】

Electronic Ballast

Electronic Dimmable Ballasts for Compact Fluorescent Lamps


General information about Electronic Dimmable Ballasts for Compact Fluorescent Lamps : Rated voltage : AC220-240V Voltage range : 187-253V 50/60Hz Starting type : Pre-heat Power Factor 0.98 THD <15% Crest Factor <1.5 Input control : DC 1-10V 0.5mA Dimming range : 3%~100% for TC-D, TC-T Lamps ; 5%~100% for TC-L Lamps After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of emergency and EOL. Comply with IEC60929, IEC61347-1, IEC61347-2-3, IEC61000-3-2, EN55015, EN61547 Meet with EMC directive Applying to 1 lamp or 2 lamps 1x18W – 1x26W - 1x32W – 1x42W PL Lamps ; 2x18W – 2x26W – 2x32W – 2x42W TC Lamps Material : Metal

【WIRE DIAGRAM】

1 x 1

1 x 2

Dim L (mm) W (mm) H (mm) Mounting distance

A 359 30 27 346mm


Line Current


Factor Dim.

LMBLS-127 1 x 8,24,36,40W PL-L/TC-L AC220-240V 0.078-0.156A 0.98 <15% <1.5 A

LMBLS-128 2 x 8,24,36,40W H-tube AC220-240V 0.150-0.315A 0.98 <15% <1.5 A

LMBLS-129 1 x 10,13W PL-L/TC-D AC220-240V 0.056-0.066A 0.98 <15% <1.5 A

LMBLS-130 2 x 10,13W PL-C/TC-D AC220-240V 0.100-0.120A 0.98 <15% <1.5 A

【68】

Electronic Ballast

Electronic Ballasts for Special Purpose Lamps Introduction & Wire Diagram :

General information about Electronic Ballasts for Special Purpose T8 Fluorescent Lamps : Rated voltage : AC220-240V 50/60Hz Starting type : Instant Power Factor 0.98 THD <15% or <10% Crest Factor <1.7 After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of emergency. Ambient temperature : -10ºC ~ 50ºC Potted and sealed structure; Moisture proof and anti-vibration Low temperature rise, long life Comply with IEC60929, IEC61347-1, IEC61347-2-3, IEC61000-3-2, EN55015, EN61547 Meet with EMC directive Applying to 1 lamp or 2 lamps 1x18W – 1x30W - 1x36W – 1x58W T8 Lamps; 2x18W – 2x30W – 2x36W T8 Lamps Material : Metal


A 260 40 29 240mm

B 335 40 29 320mm

【WIRE DIAGRAM】

1

1x18W – 1x30W - 1x36W – 1x58W T8 Lamps

2 2x18W – 2x30W – 2x36W T8 Lamps

3

2x30W – 2x36W T8 Lamps

【69】

Model No. Lamp Type Line Current


Factor Dim. Wiring Diagram

LMBLS-131 1 x 18W 0.085A 0.98 <15% <1.7 A 1

LMBLS-132 1 x 30W 0.140A 0.98 <15% <1.7 A 1

LMBLS-133 1 x 36W 0.165A 0.98 <15% <1.7 A 1

LMBLS-134 1 x 58W 0.270A 0.98 <15% <1.7 A 1

LMBLS-135 2 x 18W 0.165A 0.98 <15% <1.7 B 2

LMBLS-136 2 x 30W 0.275A 0.98 <15% <1.7 B 2

LMBLS-137 2 x 36W 0.330A 0.98 <15% <1.7 B 2

LMBLS-138 2 x 30W 0.275A 0.98 <15% <1.7 B 3

LMBLS-139 2 x 36W 0.330A 0.98 <15% <1.7 B 3

【70】

Electronic Ballast

Electronic Ballasts for HOF Lamps Introduction & Wire Diagram :

General information about Electronic Ballasts for HOF Lamps : Rated voltage : AC120V Output voltage : 700 or 900 VAC Output frequency : self-adjusting range of 25 ~ 35KHz Power factor 0.99 Operate Lamp : 8~32 feet ; 10~48 feet ; 10~40 feet High Output T12 Potted and sealed structure ; Moisture proof and anti-vibration. Thermally protected After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of emergency. Comply with UL935, UL approval Meet with EMC directive Applying to Landscape Lighting Lamps quantity : 1 to 6, 2 to 6, 1 to 4


A 362 80.8 66.5 M1=349.3mm M2=50.8mm

【WIRE DIAGRAM】

1 to 6 lamps, 2 to 6 lamps

1 to 4 lamps

Model No. Operate Lamp Type Lamp Q’ty Rated

Voltage Line

CurrentPower Factor

Output Voltage Dim.

LMBLS-140 8~32 feet HO T12 1 to 6 AC120V 1.80A 0.99 700VAC A



【71】

Electronic Ballast

Electronic Ballasts for CCFL Lamps Introduction & Wire Diagram :

General information about Electronic Ballasts for CCFL Lamps : Rated voltage : AC120V 50/60Hz Output voltage : <1000 VAC Output frequency : self-adjusting range of 25 ~ 35KHz Power factor 0.67 Potted and sealed structure ; Moisture proof and anti-vibration. EMI filtered After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of emergency. Comply with UL935, UL approval Comply with IEC61050, IEC50107, IEC61347-2-10, IEC61000-3-2, EN60065, EN55015, EN61547 Meet with EMC directive Applying to Landscape Lighting, Architectural Lighting Lamps quantity : 1 lamp or 2 lamps


A 216 58.5 44.5 M1=200.5mm M2=43.2mm

【WIRE DIAGRAM】

Model No. Rated

Voltage Max. Input

Current Volt Amp

Output Current

Output Voltage

Power Factor Dim.

LMBLS-143 AC120V 1.60A 190 0.120A ＜1000VAC 0.67 A

LMBLS-144 AC120V 0.80A 190 0.120A ＜1000VAC 0.67 A

LMBLS-145 AC120V 0.70A 190 0.120A ＜1000VAC 0.67 A

【72】

Electronic Ballast

Electronic Ballasts for Railway Train Lamps 220VAC Introduction & Wire Diagram :

General information about Electronic Ballasts for Railway Train Lamps : Rated voltage : AC 220-240V 50/60Hz Starting type : Pre-heat Power factor 0.96 or 0.98 THD <15% Crest factor <1.7 Potted and sealed structure ; Moisture proof and anti-vibration. After lamp is replaced, the electronic ballast can be re-set automatically. It’s with reliable protection of emergency. Switch times : >30,000 times Comply with IEC60929, IEC61347-1-, IEC61347-2-3, IEC61000-3-2, EN55015, EN61547 Meet with EMC directive Applying to Railway Train 1x15W T8/T10/T12 – 1x20W T10/T12 - 1x18W T8 - 1x40W T10/T12 – 1x36W T8

– 1x30W T8/T10/T12


A 180 51 32 168.5mm

【WIRE DIAGRAM】

Model No. Rated Voltage Lamp Type Line Current


Factor Dim.

LMBLS-146 AC220-240V 1 x 15W T8/T10/T12

0.070A 0.96 <15% <1.7 A

1 x 20W/T10/T12 0.95A 0.96 <15% <1.7 A LMBLS-147 AC220-240V

1 x 18W/T8 0.85A 0.96 <15% <1.7 A

1 x 40W/T10/T12 0.180A 0.98 <15% <1.7 A LMBLS-148 AC220-240V

1 x 36W/T8 0.170A 0.98 <15% <1.7 A

LMBLS-149 AC220-240V 1 x 30W T8/T10/T12

0.145A 0.98 <15% <1.7 A

【73】

Electronic Ballast

Electronic Ballasts for Railway Train Lamps 110V DC


General information about Electronic Ballasts for Railway Train Lamps : Rated voltage : DC 110V Starting type : Pre-heat Crest factor <1.7 Ambient temperature : -25ºC ~ 70ºC Potted and sealed structure ; Moisture proof and anti-vibration. It’s with reliable protection of emergency. Switch times : >100,000 times Meet with EMC directive Applying to Railway Train 1x15W T8/T10/T12 – 1x20W T10/T12 - 1x18W T8 - 1x40W T10/T12 – 1x36W T8 Material : Metal


A 180 51 32 168.5mm

【WIRE DIAGRAM】

Model No. Rated Voltage Lamp Type Line

CurrentCrest Factor Dim.

LMBLS-150 DC110V 1 x 15W T8/T10/T12

0.135A <1.7 A

1 x 20W/T10/T12 0.180A <1.7 A LMBLS-151 DC110V

1 x 18W/T8 0.160A <1.7 A

1 x 40W/T10/T12 0.360A <1.7 A LMBLS-152 DC110V

1 x 36W/T8 0.325A <1.7 A

【74】

Electronic Ballast

Electronic Ballasts for Railway Train Lamps 24V DC Introduction & Wire Diagram :

General information about Electronic Ballasts for Railway Train Lamps : Rated voltage : DC 24V Starting type : Pre-heat Crest factor <1.7 Ambient temperature : -25ºC ~ 70ºC Potted and sealed structure ; Moisture proof and anti-vibration. It’s with reliable protection of emergency. Switch times : >100,000 times Meet with EMC directive Applying to Railway Train 1x15W T8/T10/T12 – 1x20W T10/T12 - 1x18W T8 - 1x40W T10/T12 – 1x36W T8 Material : Metal


A 180 51 32 168.5mm

【WIRE DIAGRAM】

1 x 1


Crest Factor Dim.

LMBLS-153 DC24V 1 x 15W/T8/T10/T12 0.625A <1.7 A

1 x 20W/T10/T12 0.830A <1.7 A LMBLS-154 DC24V

1 x 18W/T8 0.750A <1.7 A

1 x 40W/T10/T12 1.750A <1.7 A LMBLS-155 DC24V

1 x 36W/T8 1.500A <1.7 A

【75】

Electronic Ballast

Electronic Ballasts for Railway Train Lamps 48V DC Introduction & Wire Diagram :

General information about Electronic Ballasts for Railway Train Lamps : Rated voltage : DC 48V Starting type : Pre-heat Crest factor <1.7 Ambient temperature : -25ºC ~ 70ºC Potted and sealed structure ; Moisture proof and anti-vibration. It’s with reliable protection of emergency. Switch times : >100,000 times Meet with EMC directive Applying to Railway Train 1x15W T8/T10/T12 - 1x20W T10/T12 - 1x18W T8 - 1x40W T10/T12 – 1x36W T8

- 2x15W T8/T10/T12 – 2x20W T8/T10/T12 Material : Metal


A 180 51 32 168.5mm

【WIRE DIAGRAM】

1 x 1

1 x 2


Crest Factor Dim.


1 x 20W/T10/T12 0.415A <1.7 A LMBLS-157 DC48V

1 x 18W/T8 0.375A <1.7 A

1 x 40W/T10/T12 0.830A <1.7 A LMBLS-158 DC48V

1 x 36W/T8 0.750A <1.7 A


LMBLS-160 DC 48V 2 x 20W/T8/T10/T12 - <1.7 A

【76】

Electronic Ballast

Electronic Ballasts for Multi Unit Train, Bus and Boats Introduction & Wire Diagram :

General information about Electronic Ballasts for Multi Unit Train, Bus and Boats : Rated voltage : DC 110V or AC 220V Starting type : Pre-heat Crest factor <1.7 Ambient temperature : -25ºC ~ 70ºC Frequency above 43KHz It’s with reliable protection of emergency. Switch times : >100,000 times Efficiency : over 80% Meet with EMC directive Applying to Railway Train, Passenger Car, Bus, Boat…etc For DC 110V : 1x15W T8 – 1x18W T8 - 1x30W T8 - 1x36W T8 – 2x18W T8

1x14W T5 – 1x21W T5 -1x28W T5 – 1x35W T5 1x7W TC – 1x9W TC – 1x6W TL – 1x8W TL – 2x7W TC – 2x9W TC – 2x6W TL –

2x8W TL For AC 220V : 1x18W T8 – 1x36W T8 – 2x18W T8


A 252 43 32 242mm

【WIRE DIAGRAM】

1 x 1

1 x 2

【77】

Model No. Rated Voltage

Voltage Range Lamp Type Line

Current Crest Factor

Dim.

1x15, 18, 30, 36W/T8 A LMBLS-161 DC110V DC77-150V

2x18W/T8

0.136 -0.328A

<1.7 A

LMBLS-162 DC110V DC77-150V 1x14, 21, 28, 35W/T5 0.155 -0.355A

<1.7 A

1x7W, 9W/TC, 1x6W, 8W/TL A LMBLS-163 DC110V DC77-150V

2x7W, 9W/TC, 2x6W, 8W/TL

0.055 -0.165A

<1.7 A

LMBLS-164 DC110V DC77-150V 1x18W/36W/T8,2x18W/T8 0.160 /0.320A

<1.7 A

LMBLS-165 AC220V AC187-253V 1x36W/2x18W/T8 0.60A <1.7 A

LMBLS-166 AC220V AC187-253V 1x18W/T8 0.85A <1.7 A

【78】

Electronic Ballast

Electronic Ballasts for Multi Unit Train, Bus and Boats Introduction & Wire Diagram :

General information about Electronic Ballasts for Multi Unit Train, Bus and Boats : Rated voltage : DC 100V Starting type : Pre-heat Crest factor <1.7 Ambient temperature : -25ºC ~ 70ºC Constant power output Protection for wrong connection of positive and negative polarity Self adjusting output to suit for various lamps Switch times : >100,000 times Meet with EMC directive Applying to Railway Train, Passenger Car, Bus, Boat…etc 1x15W T8 – 1x18W T8 - 1x30W T8 – 1x36W T8 – 1x20W T10/T12 – 1x30W T10/T12

- 1x40W T10/T12 – 110W T12


A 230 42 32 215mm

B 270 51 44 255mm

【WIRE DIAGRAM】

1 x 1

Model No. Rated

Voltage Voltage Range Lamp Type Line

Current Crest Factor Dim.

1x15, 18, 30, 36W/T8 A LMBLS-167 DC100V DC77-137.5V

1X20, 30, 40W/T10/T12

0.200 -0.400A

<1.7 A

LMBLS-168 DC100V DC77-137.5V 110W/T12 1.1A <1.7 B

electronic ballast - lumiaction - supplier and …lumibulb.com/catalog/images/p46-p78 electronic...

Documents