electro-pneumatic positionerdocs-europe.electrocomponents.com/webdocs/1414/0900766b...4 series...

CAT.ES60-18 A

Electro-Pneumatic Positioner

Series IP8000/8100 (Lever type) (Rotary type)

EXH.AIR

Folk lever joints (Rotary type)Can absorb off-centering.

A span adjuster achieves 1/2 split range

Opening current transmission (4 to 20mA DC) Can detect remote position. Non-explosion proof rotary type only.

Mounting dimensions are same as convention types, series IP6000/6100.

Spring pin

Actuator main shaft

100mm100mm

External scale plate (Rotary type)Improved visibility of opening indicator

Pressure gauge (O. D. ø43)Enlarged O.D. allows improved visibility.

With terminal box (Explosion proof)No terminal box (non-explosion proof) is available.

Vibration resistance : No resonances5 to 200HzDust resistance : Conforms toJIS F8007 IP65

Vibration resistance : No resonances5 to 200HzDust resistance : Conforms toJIS F8007 IP65

A centralized exhaust system employs the combination of the check valve and the labyrinth effect enhancing both dust resistance and water resistance performance.

(shortened by 13% y 13% compared with IP6100) compared with IP6100)100mm in height (shortened by 13% y 13% compared with IP6100) compared with IP6100)100mm in height (shortened by 13% compared with IP6100)

IP8 0 00000

MPa

MPa

OUT2

ELECTORO PNEUMATIC IP8000

P O S I T I O N E R

MPa

MPa

OUT2


P O S I T I O N E R

MPa

SMC

MPa

SMC

How to Order

Series IP8000/8100Electro-Pneumatic Positioner

Type000100

Lever type feedbackRotary type

Pressure gauge0123

None0.2MPa0.3MPa1.0MPa

NilA Note 3)

B Note 3)

CDE Note 4)

F Note 4)

GNote 5)

HJ Note 6)

None (Standard)ø0.7 Output restriction with pilot valveø1.0 Output restriction with pilot valve

Fork lever joint MFork lever joint S

For stroke 35 to 100mm with lever unitFor stroke 50 to 140mm with lever unit

Compensation spring (A) With external scale plate

With opening current transmission (4 to 20mA DC)

IP8000 has standard lever for stroke (10 to 85mm)Accessory for IP8000, 8100

small capacity actuator

Accessory for IP8100

Accessory for IP8000

For IP8000, 8100Accessory for IP8100Accessory for IP8100

Accessories Note 2)

Construction0

No terminal box1 Note 1)

With terminal box (ExsdBT5)

Note 1) For construction No.1(with terminal box), the ambient and fluid temperatures are as follows: • ExdBT5 –20 to 60°C• Non-explosion proof (non hazardous Iocations only) –20 to 80°CThe positioner body is EXdBT5 labeled.

Note 2) If two or more accessories are required, the part numbers should be made according to alphabetical order. (ex. IP8000-011-AG)

Note 3) “A” is applied to approx 90cm3-capacity actuator.“B” is applied to approx 180cm3-capacity actuator.

Note 4) Standard lever is not attached.Note 5) It is to be used together with “A” or “B” when tending to overshoot by the use of “A” or “B”.

It is mounted to the body as a replacement of the standard compensation spring.Note 6) With terminal box, Non-explosion proof. Select “1” for the construction.

Specifications

Type

Input currentInput resistanceSupply air pressureStandard strokeSensitivityLinearityHysteresisRepeatabilityCoefficient of temperatureSupply pressure fluctuation

Output flow

Air consumption

Ambient and fluid temperature

Explosion proof construction

Air portElectrial connection

Wiring method

Exterior covering enclosureMaterialWeight

ItemLever type lever feedback Rotary type cam feedback

Single action Double action Single action Double action

4 to 20mADC Note 1)

235±15Ω (4 to 20mADC)

0.14 to 0.7MPa

10 to 85mm (Deflection angle 10 to 30°) 60 to 100° Note 2)

Within 0.1%F.S. Within 0.5%F.S.

Within ±1%F.S. Within ±2%F.S.

Within 0.75%F.S. Within 1%F.S.

Within 0.5%F.S.

Within 0.1%F.S. / °CWithin 0.3%F.S./0.01MPa

80l/min (ANR) or more (SUP = 0.14MPa)

200l/min (ANR) or more (SUP = 0.4MPa)

5l/min (ANR) or less (SUP = 0.14MPa)

11l/min (ANR) or less (SUP = 0.4MPa)

–20 to 80°C (Non-explosion proof)

–20 to 60°C (Flame proof and explosion proof)

Flame proof and explosion proof construction: ExdBT5(Certificate number: C15916 of Technology lnstitution of Industrial Safety)

Rc 1/4 female

G 1/2 female

Flame proof packing system, Sealant fitting system (explosion-proof)

Resin G 1/2 connector (Non-Explosion proof, option)

JISF8007, IP65 (conforms to IEC Pub.529)

Aluminum diecast body / epoxy resin

With terminal box 2.6kg (None 2.4kg)

IP8000 IP8100

Note 1) 1/2 Sprit range (Standard)Note 2) Stroke adjustment: 0 to 60°C, 0 to 100°C

Explosion ProofThis product has the following approvals.ExdBT5: Newly established standard based on international (IEC 79)

Use as ExdBT5(A) Pressure-proof packing.

As shown below in the chart, use “Cable gland” (option).(B) Metal Piping.

Attach the sealant fitting near the cable port.(For details, refer to “The guideline on electric equipment explosion proof” published by the Technology Institution of Industrial Safety.)

Pressure proof packing connector unitCable

Packing

Lock screw(Hexagon 1.5)

Cable gland with flame proof packing (Option)Part name

Flame proof packingconnector unit

Part numberP368010-32P368010-33

Suited cable outer diameterø7.0 to ø10.0ø10.1 to ø12.0

1

SMC

MPa

SMC

MPa

SUP

OU

AM

SPAN


P O S I T I O N E R

Series IP8000 / 8100 Electro-Pneumatic Positioner

Accessory / Option

Pilot valve with output restriction (IP8000, 8100 type)In general, mounting on a small-size actuator may cause hunting. For prevention, a pilot valve with a built-in output restriction is available. The restriction is removable.

Actuator Capacity

90cm3

180cm3

Orifice size

ø0.7

ø1

Part number

P36801080

P36801081

Pilot unit part number

P565010-18

P565010-19

Fork lever joints (IP8100 type)Two types of the fork lever joints are available dependent upon different mounting dimensions.This is recommended because it can absorb off-centering, compared with direct mounting type.

M8 x 1.25

Side mounting with the fork lever assembly M

63

(S ty

pe: 3

9)L1

=10

1(S

type

: 77)

Actuator main shaft

Side mounting with the fork lever assembly S

39

(M ty

pe: 6

3)

L2=

31(M

type

: 55)

Actuator main shaft

M8 x 1.25

External feedback lever (IP8000 type)

Stroke

10 to 85mm (Accessory “Nil”)

35 to 100mm (Accessory “E”)

50 to 140mm (Accessory “F”)

Unit number

P368010-20

P368010-21

P368010-22

Size M

125

110

110

Size N

150

195

275

Different feedback levers are available dependent upon valve strokes. Consult with SMC in case of 10mm or less stroke.

Resin connector (Non-explosion proof specification)Optional cable connectors are available for different cable sizes.These are not for explosion proof applications.

166.1

N

M 5Part name

Fork lever assembly M

Fork lever assembly S

Part number

P368010-24

P368010-25

Part name

Resin-made cable clamp unit (A)

Resin-made cable clamp unit (B)

Part number

P368010-26

P368010-27

Suited cable outer diameter

ø7 to ø9

ø9 to ø11

Cable connector G1/2

Exploded View

Description

Pilot valve unit

Base seal

Cover seal

No.

1

2

3

Part no.

P565010-7

P56501012-3

P56501013

Note

IP8000/8100

Replacement Parts

(2) Base seal

Terminal joint unit (No terminal box)

Terminal box unit

Body unit

Feedback lever unit

Feedback shaft assembly

Mini-terminal unit (No terminal box)

(3) Cover seal

Body cover unit

Torque motor unit

Feedback spring

Compensation spring(1) Pilot valve unit

Zero adjusting unit

Span adjusting unit

Cable connector (option)

2

Series IP8000/8100

Piping

IP8000 / Lever type

Po

siti

ve o

per

atio

nR

ever

se o

per

atio

n

Double actionSingle action

When the input signal is increased, the stem moves as allow mark.

When the input signal is increased, the stem moves as allow mark.

When the input signal is increased, the stem moves as allow mark.(Reverse valve operation by its positive operation mode)

When the input signal is increased, the stem moves as allow mark.(Positive valve operation by its reverse operation mode)

OUT2 is plugged.

XOUT1

SUP

IN -+

OUT1 is plugged.

X

OUT2

SUP

Span adjusting lever reverse position

Span adjusting lever reverse position

Span adjusting lever reverse positionIN -

+

OUT1 is plugged.

X

OUT2

SUP

Span adjusting lever normal position

Span adjusting lever normal positionIN -

+

OUT1

OUT2 is plugged.

X

SUP

Span adjusting lever normal positionIN -

+

When the input signal is increased, the cylinder rod moves as allow mark.

When the input signal is increased, the cylinder rod moves as allow mark.

OUT1

OUT2

SUP

IN -+

OUT1

OUT2

SUP

IN -+

IP8100 / Rotary type

When the input signal is increased, the actuator shaft rotates in a clockwise direction.

Single action

When the input signal is increased, the actuator shaft rotates in a clockwise direction.(Positive valve operation by its reverse operation mode)

When the input signal is increased, the actuator shaft rotates in a counter clockwise direction.

When the input signal is increased, the actuator shaft rotates in a counter clockwise direction.(Reverse valve operation by its positive operation mode)

Main shaftSingle action actuator

The cam of thepositionershould be set on the RA surface.

OUT2 is plugged.

XOUT1

IN -+

SUPThe cam of thepositionershould be set on the RA surface.

OUT1 is plugged.

X


OUT2

IN -+

SUP


OUT2

The cam of thepositionershould be set on the DA surface.

OUT1 is plugged.

IN -+

SUP

X


OUT2 is plugged.


OUT1

IN -+

SUP

X

Po

siti

ve o

per

atio

nR

ever

se o

per

atio

n

Double action

When the input signal is increased, the actuator shaft rotates in a clockwise direction.

When the input signal is increased, the actuator shaft rotates in a counter clockwise direction.

The cam of thepositionershould be set on the RA surface.

OUT1

Main shaftDouble action actuator

OUT2

IN -+

SUP


OUT2

Main shaftDouble action actuator

OUT1

IN -+

SUP

3

4


Installation

IP8000 type (Lever type lever feedback)

2 A connecting fitting or pin to transfer the displacement of valve stem should be mounted at a position so that the feedback lever is at right angles to the valve stem for an input current of 50%. The right figure is the configuration viewed from the front.

1 The unit should be mounted using bolts firmly fixed through mounting holes on the side or back of the positioner.

1 The positioner should be mounted so that the feedback shaft is aligned with the shaft of the rotary actuator.

IP8100 type (Rotary type cam feedback)

Positioner

Backlash eliminating spring

Feedback lever

Positioner body

Right angle

Connecting fitting

Valve stem

With front bracketWith L-type bracket

Bracket

Positioner

Bracket

Bracket

Positioner

Bracket

Input current 100% position

Input current 50% position

Input current 0% position(Or 100%)

(Or 0%)

Bracket

OUT2OUT1

OUT2OUT1

Installation using the threadon the back of positioner

Installation using the thread on the side of positioner

Direct mounting to diaphragm

Mounting examples

MA

E

When the input current increases, (11) the plate spring of (12) the torque motor will work as a pivot, (13) armature will receive a counter clockwise torque, (4) the counter weight will be pushed to the left, the clearance between (6) the nozzle and (5) the flapper will increase, and the nozzle back pressure will decrease. Consequently, (7) the exhaust valve of (1) the pilot valve moves to the right, the output pressure of OUT1 increases and (15) the diaphragm moves downwards. The motion of (15) the diaphragm acts on (10) the feedback spring through (8) the feedback lever, (14) the transmission lever and (9) the span adjustment lever to rest at the balance position generated by the input current. (2) The compensation spring is for direct feedback of the motion of (7) the exhaust valve to (4) the counter weight to increase the stability of the loop. The zero point should be adjusted by change of (3) the zero adjustment spring tention.

Series IP8000/8100

Principle of Operation

IP8000 / Lever type

Block diagram

Single action positive operation

X

SUP OUT2 OUT1

X View

Stopper screw(Do not move)

(1) Pilot valve

Supply valve B

EXH.(4) Counter weight

Zero adjusting screw

(3) Zero adjusting spring

(2) Compensation spring

Diaphragm

(5) Flapper

(6) Nozzle

Input current terminal

Automatic / Manual change-over screw

(Built-in bleed restriction)

Sensitivity adjusting screw(Adjusts GAIN)

Supply valve A

(9) Span adjusting lever

(7) Exhaust valve

(8) Feedback lever

(15) Diaphragm valve

Span adjusting lever shaft

Transmission pin

Lock screw

Span adjusting screw

(14) Transmission lever

For reverse position, exchange the shaft of the span adjusting lever to the opposite side. The span adjusting screw faces upward in this condition. (See “Piping”)

(11) Plate spring

(10) Feedback spring

(13) Armature

(12) Torque motor

SUP

--++

()Zero adjusting spring

Torque motorIN

Current

Restriction

Nozzleflapper

Diaphragm

Compensatoryspring

Feedbackspring

Exhaust valve Supply valve

Span adjustinglever

Feedbacklever

Diaphragm valve

OUT

Stem stroke

5

MA


IP8100 / Rotary type

Double action positive operation

When the input current increases, (12) the plate spring of (13) the torque motor will work as a pivot, (14) armature will receive a counter-clockwise torque, (4) the counter weight will be pushed to the left and the clearance between (6) the nozzle and (5) the flapper will increase, and the nozzle back pressure will decrease. Consequently, (7) the exhaust valve of (1) the pilot valve moves to the right, the output pressure of OUT1 increases that of OUT2 decreases and (16) the rotary actuator moves. The motion of (16) the actuator acts on (10) the feedback spring through (11) the feedback shaft, (8) the cam, (9) the span adjustment lever and (15) transmission lever to rest at the balance position generated by the input current. (8) the cam is set on the DA surface and operates positively while (16) the oscillating actuator shaft rotates in a clockwise direction when the input signal is increased. (2) The compensation spring is for direct feedback of the motion of (7) the exhaust valve to (4) the counter weight to increase the stability of the loop. The zero point should be adjusted by change of (3) the zero adjustment spring tension.

X View

X

EXH.

SUP OUT2 OUT1

Stopper screw(Do not move)

(1) Pilot valve

Supply valve B

(4) Counter weight

E

Zero adjusting screw

(3) Zero adjusting spring

(2) Compensation spring

Input current terminal

Automatic / Manual change-over screw

(Built-in bleed restriction)

Sensitivity adjusting screw(Adjusts GAIN)

Supply valve A

(7) Exhaust valve

Diaphragm

(9) Span adjusting lever

(12) Plate spring

(13) Torque motor

(14) Armature

(11) Feedback shaft

(10) Feedback spring

(8) Cam

Pairing

(15) Transmission lever

Fork joint

For reverse position, set by turning over the cam and reversing connections of outlets OUT1 and OUT2.

(16) Oscillating actuator

--++

SUP

IN

Current

Zero adjusting spring

Torque motor

Restriction ()

Block diagram

Nozzleflapper

Feedbackspring

Diaphragm

Compensatoryspring

Span adjustinglever

Cam

Exhaust valve Supply valve

Angle of rotationOUT

Feedback shaft

Oscillating actuator

(5) Flapper

(6) Nozzle

6

Series IP8000/8100

MPa

MPa

1E

OUT2


P O S I T I O N E R

E

MPa

MPa

OUT2


P O S I T I O N E R

Dimensions / IP8000 (Lever type)

IP8000-00 (No terminal box)110

38

OUT2.Rc1/4With plug

35

3911

38

OUT1.Rc1/4SUP.Rc1/4

A

G1/2Electric conduit

122

1984323.5

939

117

147

Approx.194125

6520

150

125

542

50

166.1

2 x M8 x 1.25 depth12(Female thread for side mounting)

4 x M8 x 1.25 depth12(Female thread for rear mounting)

View A

23.558110192

4035

22.5

At accessory “E”: 110At accessory “F”: 110




46302

14

100

With optional resin cable clampApplicable cable O. D. ø7 to 9:P368010-26Applicable cable O. D. ø9 to 11:P368010-27

IP8000-01 (With terminal box)OUT2.Rc1/4With plug

110

38

60 30214

100

42

162

117

218

939

4323.5

12512 1688

3911

38

2050

166.1

A

150

125

OUT1.Rc1/4

SUP.Rc1/4

122

58

192

23.511040

35

65

5

View A

4 x M8 x 1.25 depth12(Female thread for rear mounting)

2 x M8 x 1.25 depth12(Female thread for side mounting)

Electric conduit 2 x G1/2

22.5

7

25%

100%

75%

DA

50%

0%

MPa

MPa1E

OUT2


P O S I T I O N E R

25%

100%

75%

DA

50%

0%

MPa

MPa

E

OUT2


P O S I T I O N E R


Dimensions / IP8100 (Rotary type)

IP8100-00 (No terminal box)

231198

147 11

7

Approx.194

35

939

4323.5

3911

3838

110

125

At accessory “H”: (with external scale plate)

G1/2Electric conduit

OUT1.Rc1/4SUP.Rc1/4

OUT2.Rc1/4

With optional resin cable clampApplicable cable O. D. ø7 to 9:P368010-26Applicable cable O. D. ø9 to 11:P368010-27

A

46

1512

2

4250

20

58

192

23.5

100

1104035

65

22.5

44

2 x M8 x 1.25 depth12Female for side mounting

4 x M8 x 1.25 depth12Female for rear mounting

View A

IP8100-01 (With terminal box)

251

46

1512

2

5042

20

60

58218

162

117

939

4323.5

192

23.5

100

8

3911

38

38

110

1104035

65

22.5

44

12512 168

At accessory “H”: (with external scale plate)

2 x M8 x 1.25 depth12Female thread for side mounting

2 x G1/2Electric conduit

4 x M8 x 1.25 depth12Female thread for rear mounting

OUT1.Rc1/4SUP.Rc1/4

View A

OUT2.Rc1/4

A

8

Series IP8000/8100

Safety Instructions

Note 1) ISO 4414: Pneumatic fluid power -- General rules relating to systems

Note 2) JIS B 8370: Pneumatic system axiom

Warning

Caution : Operator error could result in injury or equipment damage.

Warning : Operator error could result in serious injury or loss of life.

Danger : In extreme conditions, there is a possible result of serious injury or loss of life.

These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These instructions indicate the level of potential hazard by a label of "Caution", "Warning" or "Danger". To ensure safety, be sure to observe ISO 4414 Note 1), JIS B 8370 Note 2) and other safety practices.

1. The compatibility of pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications.Since the products specified here are used in various operating conditions, their compatibility with the specific pneumatic system must be based on specifications or after analysis and/or tests to meet your specific requirements. The expected performance and safety assurance will be the responsibility of the person who has determined the compatibility of the system. This person should continuously review the suitability of all items specified, referring to the latest catalog information with a view to giving due consideration to any possibility of equipment failure when configuring a system.

2. Only trained personnel should operate pneumatically operated machinery and equipment.Compressed air can be dangerous if handled incorrectly. Assembly, handling or maintenance of pneumatic systems should be performed by trained and experienced operators.

3. Do not service machinery/equipment or attempt to remove components until safety is confirmed.1. Inspection and maintenance of machinery/equipment should only be performed once measures to

prevent falling or runaway of the driven object have been confirmed. 2. When equipment is to be removed, confirm the safety process as mentioned above. Cut the supply

pressure for this equipment and exhaust all residual compressed air in the system.3. Before machinery/equipment is restarted, take measures to prevent shooting-out of cylinder piston

rod, etc. (Bleed air into the system gradually to create back pressure.)

4. Contact SMC if the product is to be used in any of the following conditions:1. Conditions and environments beyond the given specifications, or if product is used outdoors.2. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles, medical

equipment, food and beverages, recreation equipment, emergency stop circuits, clutch and brake circuit in press applications, or safety equipment.

3. An application which has the possibility of having negative effects on people, property, or animals, requiring special safety analysis.

9

Series IP8000/8100Electro-Pneumatic Positioner PrecautionsBe sure to read before handling.

Operation Maintenance

Handling

Air Supply

Operating Environment

Warning

Caution

Caution

Caution

Warning

Caution

1. Do not operate the positioner outside the specified range as this may cause problems. (Refer to the specifications.)

2. Design the system to include a safety circuit to avoid the risk of danger should the positioner suffer failure.

3. Be sure that exterior lead-in wiring to the terminal box is based on the guidelines for explosion-protection of manufactory electric equipment when being used as a flame proof, explosion proof construction.

4. Do not remove terminal cover in a hazardous location while the power is on.5. Covers for the terminal and body should be in place while operating.

1. Avoid impact to the positioner body or torque motor and any excessive force to the armature, as these actions may cause damage to the product.Handle carefully while transporting and operating.

2. When exposed to possible moisture invasion, please take the necessary measures. For example, if the positioner is left on-site for long periods, a plug should be put in the piping port and an external cover fitted to avoid water penetration.Take measures to avoid dew condensation inside the positioner if exposed to high temperature and humidity. Take enough measures against condensation especially when packing for export.

3. Keep magnetic field off the positioner, as this affects its characteristics.

1. Use only dehumidified and dust-extracted clean compressed clean air as the positioner contains extra-fine orifices such as restrictor and nozzle.Do not use a lubricator.

2. Do not use compressed air containing chemicals, organic solvents, salinity or corrosive gases, as this may cause malfunction.

3. Use dehumidified and dust-extracted clean compressed air as an air supply.4. When operating below the freezing point, protect the positioner from

freezing.

1. Do not operate in locations with an atmosphere of corrosive gases, chemicals, sea water, or where these substances will adhere to the regulator.

2. Do not operate in locations where excessive vibration or impact occurs.3. Do not operate out of the indicated operation temperature range to avoid

deterioration of the seals, as this may cause possible positioner problems.

1. After installation, repair or disassembly, connect compressed air and conduct tests to confirm appropriate function and leakage.Do not use the positioner when noise from the bleeder sounds louder compared with the initial state, or when it does not operate normally. If these occur, check immediately if assembled and mounted correctly.Never modify electrical construction to maintain explosion-proof construction.

1. Confirm whether the compressed air is clean.Dust, oil, or moisture mixed within the equipment may result in malfunction and positioner problems. Perform periodic inspection of the air preparation equipment to ensure clean air is always supplied.

2. Improper handling of compressed air is dangerous. Not only observing the product specifications, but also replacement of elements and other maintenance activities should be performed by personnel having sufficient knowledge and experience pertaining to instrumentation equipment.

3. Perform annual inspections of the positioner.Replace badly damaged seals and units such as diaphragm and O-ring during the inspection.When used in tough environmental and/or service conditions such as seaside locations, replacements should be undertaken more frequently.

4. When performing inspections, demounting the positioner, or replacing the elements with the positioner still in its mounted position, first, stop the compressed air, then exhaust the residual pressure before undertaking operation.

5. Should the restrictor become clogged with carbon particles, etc., demount automatic/manual change-over screw (with built-in restrictor) and clean it using a ø0.2 wire.Stop the compressed air and remove the screw to switch the pilot valve off before replacing the restrictor.

6. Apply just a small amount of grease to sliding parts (O-ring and exhaust valve) when disassemble a pilot valve.Use silicone grease, for example, SH45 produced by Du Pond-Toray Co., Ltd.

7. Confirm air leakage from compressed air piping and junctions.Air leakage from air piping results in reduced operational performance and a decline of characteristics, etc.It is structurally necessary for air to be released from the bleeder, it is not abnormal as long as the air consumption is within the specified range.

10

EUROPESLOVENIASMC Industrijska Avtomatika d.o.o.

SPAIN/PORTUGALSMC España, S.A.

SWEDENSMC Pneumatics Sweden AB

SWITZERLANDSMC Pneumatik AG.

UKSMC Pneumatics (U.K.) Ltd.

ASIACHINASMC (China) Co., Ltd.

HONG KONGSMC Pneumatics (Hong Kong) Ltd.

INDIASMC Pneumatics (India) Pvt. Ltd.

MALAYSIASMC Malaysia (S.E.A.) Sdn. Bhd.

PHILIPPINESSMC Pneumatics (Philippines), Inc.

SINGAPORESMC Pneumatics (S.E.A.) Pte. Ltd.SOUTH KOREASMC Pneumatics Korea Co., Ltd.

TAIWANSMC Pneumatics (Taiwan) Co., Ltd.

THAILANDSMC Thailand Ltd.

NORTH AMERICACANADASMC Pneumatics (Canada) Ltd.

MEXICOSMC Corporation (Mexico) S.A. de C.V.USASMC Corporation of America

SOUTH AMERICAARGENTINASMC Argentina S.A.

BOLIVIASMC Pneumatics Bolivia S.R.L.

BRAZILSMC Pneumaticos Do Brazil Ltda.

CHILESMC Pneumatics (Chile) S.A.

VENEZUELASMC Neumatica Venezuela S.A.

OCEANIAAUSTRALIASMC Pneumatics (Australia) Pty. Ltd.

NEW ZEALANDSMC Pneumatics (N.Z.) Ltd.

EUROPEAUSTRIASMC Pneumatik GmbH

CZECHSMC Industrial Automation CZ s.r.o.

DENMARKSMC Pneumatik A/S

FINLANDSMC Pneumatics Finland Oy

FRANCESMC Pneumatique SA

GERMANYSMC Pneumatik GmbH

HUNGARYSMC Hungary Ipari Automatizálási Kft.

IRELANDSMC Pneumatics (Ireland) Ltd.

ITALYSMC Italia S.p.A.

NETHERLANDSSMC Pnuematics BV.

NORWAYSMC Pneumatics Norway A/S

POLANDSMC Industrial Automation Polska Sp.z.o.o.

ROMANIASMC Romania s.r.l.

RUSSIA SMC Pneumatik LLC.

SLOVAKIASMC Priemyselná automatizáciá, s.r.o.

SMC'S GLOBAL MANUFACTURING, DISTRIBUTION AND SERVICE NETWORK

1-16-4 Shimbashi, Minato-ku, Tokyo 105-0004, JAPANTel: 03-3502-2740 Fax: 03-3508-2480URL http://www.smcworld.com© 2003 SMC CORPORATION All Rights Reserved

1st printing July, 2003 D-YGA P-120 (YG)This catalog is printed on recycled paper with concern for the global environment.

All specifications in this catalog are subject to change without notice.Printed in Japan.

electro-pneumatic positionerdocs-europe.electrocomponents.com/webdocs/1414/0900766b...4 series...

Documents