eii shw val elite sqr pvt 1345090-a02-f · fit the corner covers to the wall channels. they should...
TRANSCRIPT
1345090-A02-F August 2020
INSTALLATION INSTRUCTIONS
SHOWER
Engle�eld
VALENCIA ELITE Pivot Door & Side Panel
Englefield has a history of making superb showers and their popularity is testament to their quality and affordability.
It’s the details that Englefield cares about - from pioneer-ing the latest technology, to innovative design, it’s all to make your showering experience the very best it can be.
Note: Tapware and accessories not included.
Page 1
Before installing the shower please read these instructions carefully to familiariseyourself with the required tools, materials and installation sequences. Please leave theseinstructions for the consumer after installation. Refer to the separate care and maintenanceguide for important care and cleaning information.
Ensure that the shower tray and wall, if applicable, are completely finished prior toinstalling your shower door and return. Follow all warnings, cautions and instructionscontained in this guide.
1. ENGLEFIELD strongly recommends that a minimum of TWO persons install this enclosure due to the weight of the door panels. 2. Toughened safety glass cannot be cut. Risk of injury or product damage.
3. Wear protective footwear when lifting panels.
4. Wear safety glasses when drilling.
1. The wall retainers must be installed onto a waterproof, vertical and flat wall surface. Failure to do so will result in an unsatisfactory seal, which may cause property damage. The wall inclination (out of squareness) is recommended to be out by no more than +/- 4mm/m. 2. Please install this door onto an ENGLEFIELD Quick - Fit shower tray only, unless installing directly onto tiled walls and floor.
®
3. Care must be taken when drilling into walls and floors to avoid any hidden pipes or
wires.
4. It is the responsibility of the INSTALLER to ensure that the installation complies with council and or local authority bylaws.
INSTALLATION INSTRUCTIONSVALENCIA ELITE Pivot Door And Side Panel
BEFORE YOU BEGIN
SAFETY !
! ATTENTION
Instructions, drawings, and diagrams contained in this manual present information available at the time of printing.
changes without further notice.
ENGLEFIELD
Page 2
INSTALLATION INSTRUCTIONS
TOOLS AND MATERIALS REQUIRED
PARTS IDENTIFICATION
ENGLEFIELD
3.0 mm
#1Square
Drive
!ATTENTIONShort section of dripstrip may be packedwith different seals.
Do not discard.
8 x Wall Plugs
1 x Hex Key
8 x Fixing Screws
1 x Pivot Door (pre-assembled)
1 x Drip Strip Extrusion
2 x Top Caps
Door Fitting Kit
Handle Kit
Side Panel Fitting Kit
2 x Top Caps
1 x Seal Pack 1 x Side Panel
2 x Wall Channels
2 x Corner Covers
2 x Wall Finishing Strips
8 x Assembly Screws B
A
VALENCIA ELITE Pivot Door And Side Panel
1 x Handle Assembly 1 x Hex Key
2mm
3mm
4 x Assembly Screws
2 x Top Caps
1 x Top Cap
1 x Screw Spacer
4 x Cover Caps
C
CONSTRUCTION REQUIREMENTS
Due to the weight of the glass panels Englefield strongly recommendsconstructing double studs (as below) to fix the wall retainers to.
!ATTENTION
Page 3
INSTALLATION INSTRUCTIONS
A
Double studs
Double studs
B
ENGLEFIELD
VALENCIA ELITE Pivot Door And Side Panel
Size Dim ‘A’ Dim ‘B’
750 x 900 LH 760 900
750 x 900 RH 900 760
900 x 750 LH 900 760900 x 750 RH 760 900
Size Dim ‘A’
900 x 900 900
1000 x 1000 1000
Dim ‘B’
900
1000
1200 x 900 LH 1200 900
1200 x 900 RH 900 1200
2025mmMinimumHeight
Tray: For tray installation refer to the instructions supplied with the tray.
Wall: For wall installation refer to the instructions supplied with the wall.
- Proceed to Door and Return Installation.
- The door and return can be installed directly onto the wall and floor tiles.
- Proceed to Door and Return Installation.
OPTION 1 - Acrylic Wall & Tray
OPTION 2 - Tiled Wall & Acrylic Tray
Page 4
INSTALLATION INSTRUCTIONS
OPTION 3 - Tiled Wall & Floor
ENGLEFIELD
INSTALLATION - Options
Tray: For tray installation please refer to the instructions supplied with the tray.
Wall:- The vertical wall retainers MUST be installed onto the waterproof membrane PRIOR TO WALL TILING. If possible the complete door system should be installed onto the waterproof membrane prior to wall tiling.
CAUTION: Failure to install the wall retainers first may mean the door system may not fit on the shower tray due to the tile thickness.
- If not installing the complete door system prior to tiling, install the wall retainers and tiles. The retainer cover extrusion can be inserted after tiling - there is no need to leave a tiling gap. Refer to image.
- Proceed to Door and return installation.
Tile up toretainer
VALENCIA ELITE Pivot Door And Side Panel
± 0 mm ± 0 mm
Caution:
For tray base option: - Mark 10mm in from top edge of tray.
For tiled base option: - Mark from finished wall to outer edge of retainer.
Tip: Cover the waste to prevent the loss of small parts. If installing onto a tray protect the tray surface during installation.
Page 5
10 mm
10 mm
Page 5
INSTALLATION INSTRUCTIONS
ENGLEFIELD
INSTALLATION
1
B
A
(a) Mark the locations of the wall retainers.
level & walls are vertical & square.Ensure tray or tiled floor is
VALENCIA ELITE Pivot Door And Side Panel
750 x 900 LH750 x 900 RH
732 875 875 732
900 x 750 LH900 x 750 RH
875 732 732 875
900 x 9001000 x 1000
875 875 975 975
1200 x 900 LH1200 x 900 RH
1175 875 875 1175
ASize B
- (Mark 15mm in on 90mm sill height Quick-Fit Trays)
(15mm on QFT)
(15mm on QFT)
Page 6
INSTALLATION INSTRUCTIONS
ENGLEFIELD
(a)
Position the wall channels on the wall. The flange with pre-drilled holes should faceinside the shower enclosure. Using a level, make sure that the channel is upright.
Mark the position of the fixing holes down the centre of the channels, then remove the wall channels. Note! The wall channel is not fitted at this stage.
Drill with a 3mm bit. For other types of wall structure, alternative fixings may berequired (not supplied).
(b)
(c)
Apply silicone sealant along the length of the wall and at the bottom where the wallchannel will be placed, including the top of the tray.
(d)
Position the wall channels on the wall and install the fixing screws .(e)
Fully tighten the fixing screws, making sure that the wall channels remain vertical.(f)
2
10 mm
± 0 mm
3 mm
x4
x4
A
A
VALENCIA ELITE Pivot Door And Side Panel
(15mmon QFT)
RH
LH(b)
(c)
(d)
(d)
Page 7
INSTALLATION INSTRUCTIONS
ENGLEFIELD
3
2.0 mm
VALENCIA ELITE Pivot Door And Side Panel
( )f
=
=
Wall channel adjustmentSide Panel
(e) Corner Assembly
Pivot Door
(a)
The pivot door can be either Left-Hand or Right-Hand. To change the opening, simply rotate the frame through 180º before continuing with the installation.
(b)
(c)
(d) (e)
( )
Make sure that the pivot door and side panel engage correctly. Keep the cornerassembly pressed together and move the door frame and side panel in/out of thewall channels so that each panel is parallel with the edge of tray.Install the door handle, ensuring that the grub screws are on the underside.f
Install the side panel into the other wall channel, and fit the corner posts together.Install the door frame into the wall channel.
The door orientation denotes the direction of the side panel. Once the door is in itscorrect orientation, apply sealant along the full length inside the the drip strip extrusionand fit to the bottom edge of the side panel. Gently tap extrusion into place with arubber mallet and carefully clean away any excess sealant.
(a)
From the inside of the enclosure, drill four holes in the door frame through the centre marked points on the wall channel with a 3 mm HSS drill bit (not supplied).
(b) Install and tighten the wall channel assembly screws .
(c)
Repeat the process for the other wall channel.
(d)( )
Fit the corner covers to the wall channels. They should ‘snap’ into place.
Use the Screw Spacer to install screws into the 4 corner post holes, then tighten.Fit the caps into the corner post assembly to cover the screwheads.
4
Page 8
INSTALLATION INSTRUCTIONS
ENGLEFIELD
VALENCIA ELITE Pivot Door And Side Panel
Ø 3 mm
x4
± 0 mm
e( ) f
B
B
C
C
B
Wall channelcover assembly
(b)(a)
Page 9
INSTALLATION INSTRUCTIONS
ENGLEFIELD
VALENCIA ELITE Pivot Door And Side Panel
5a
750 DOORS900 DOORS1000 DOORS[for 1200 doors
see page 10]
Door Seal
Install the door seals onto the door.Fit the caps to the top of the extrusions. Add silicone or modify caps to fit if required.
(c) Apply sealant along the outside surfaces of the enclosure. Do not seal from inside.(d) Install the wall finishing strips, if desired.(e) Allow the silicone sealant to cure for 24 hours before use.
Full length
Full length
Full length Full length
200mm up200mm up
Door Seal
wall board
retainerchannel
silicone
silicone oradhesive
wallliner
finishingstrip
Installation complete.
VerticalDoorSeal
InsideOutside
Both ends ofside panel
bottom strip
Page 10
INSTALLATION INSTRUCTIONS
ENGLEFIELD
VALENCIA ELITE Pivot Door And Side Panel
(b)
5b
(a) Install the vertical seal onto the fixed panel.Install the door seals and magnetic strip onto the door panel.Fit the caps to the top of the extrusions. Add silicone or modify caps to fit if required.(c)
(d) Install the wall finishing strips, if desired.(e)Allow the silicone sealant to cure for 24 hours before use.
Full length
Full length
Full length
200mm up
200mm up
wall board
retainerchannel
silicone
silicone oradhesive
wallliner
finishingstrip
Installation complete.
Full length
Door Seal
Door SealMagnetic Strip
Vertical Seal
Fixedpanel
1200 DOORS[for 750, 900,1000doors see page 9]
Apply sealant along the outside surfaces of the enclosure. Do not seal from inside.
outside
inside
Both ends ofside panel
bottom strip
(f)
Page 11
INSTALLATION INSTRUCTIONS
ENGLEFIELD
VALENCIA ELITE Pivot Door And Side Panel
Horizontal Seal (750, 900, 1000)1365844Horizontal Seal (1200)1386135
Wall Retainer1278347-**
Retainer Clip1278349
Pivot Hinge1365838-**
Retainer Cover1278348-**
Wall Finishing Strip1315530-**
SPARE PARTS
Magnetic Strip Pair (750, 900, 1000)1365842Magnetic Strip Pair (1200)1380255
Wall Plugs
Fixing Screws
Handle Assembly1365840-**
Top Caps
Top Caps
Assembly Screws
Component Kit1365841-**
Scan the QR barcode on the packagingor underside of top caps to identify theproduct SKU and date of manufacture.
Door Seal (750, 900, 1000)1365843Fixed Panel Seal (1200)1376826
Pivot Block (750, 900, 1000)1365839-**Pivot Block (1200)1376827-**
Rail Seal (1200 only)1376825
Glass Aftercare Kit98945A-NA
** Colour code must be specified when ordering. (eg: white -0, black -BL, metallic -SHP, satin -SS)
CONTACT AND WARRANTY INFORMATION
NEW ZEALAND KOHLER NZ LTDFree Ph: 0800 100 382Free Fax: 0800 664 488www.englefield.co.nz
AUSTRALIA KOHLER AUSTRALIA
Free Ph: 1 800 ENGLEFIELD (1 800 364 533)www.englefield.com
Engle�eld
INSTALLATION INSTRUCTIONS
CLEANING AND MAINTENANCE INSTRUCTIONS
Please refer to our website for cleaning instructions.
For warranty information, please visit our website.
VALENCIA ELITE Pivot Door and Side Panel
Side Panel Bottom Strip 750mm1393098-**
Side Panel Bottom Strip 900mm1348296-**
Side Panel Bottom Strip 1000mm1365845-**
Side Panel Fittings Kit1348297-**
Assembly Screws
Top Caps
Top Cap
Screw Spacer
Cover Caps
** Colour code must be specified when ordering. (eg: white -0, black -BL, metallic -SHP, satin -SS)