eesti standard evs-en 13480-3:2017
TRANSCRIPT
EESTI STANDARD EVS-EN 13480-3:2017
METALLIST TÖÖSTUSTORUSTIK. OSA 3: KAVANDAMINEJA ARVUTAMINE
Metallic industrial piping - Part 3: Design andcalculation
This document is a preview generated by EVS
EVS-EN 13480-3:2017
Tagasisidet standardi sisu kohta on võimalik edastada, kasutades EVS-i veebilehel asuvat tagasiside vormivõi saates e-kirja meiliaadressile [email protected].
ICS 23.040.01
Standardite reprodutseerimise ja levitamise õigus kuulub Eesti Standardikeskusele
Andmete paljundamine, taastekitamine, kopeerimine, salvestamine elektroonsesse süsteemi või edastamine ükskõik millisesvormis või millisel teel ilma Eesti Standardikeskuse kirjaliku loata on keelatud.
Kui Teil on küsimusi standardite autorikaitse kohta, võtke palun ühendust Eesti Standardikeskusega:Koduleht www.evs.ee; telefon 605 5050; e-post [email protected]
The right to reproduce and distribute standards belongs to the Estonian Centre for Standardisation
No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, includingphotocopying, without a written permission from the Estonian Centre for Standardisation.
If you have any questions about copyright, please contact Estonian Centre for Standardisation:
Homepage www.evs.ee; phone +372 605 5050; e-mail [email protected]
EESTI STANDARDI EESSÕNA NATIONAL FOREWORD
See Eesti standard EVS-EN 13480-3:2017sisaldab Euroopa standardi EN 13480-3:2017ingliskeelset teksti.
This Estonian standard EVS-EN 13480-3:2017consists of the English text of the Europeanstandard EN 13480-3:2017.
Standard on jõustunud sellekohase teateavaldamisega EVS Teatajas.
Euroopa standardimisorganisatsioonid on teinudEuroopa standardi rahvuslikele liikmetelekättesaadavaks 28.06.2017.
This standard has been endorsed with anotification published in the official bulletin of theEstonian Centre for Standardisation.
Date of Availability of the European standard is28.06.2017.
Standard on kättesaadav EestiStandardikeskusest.
The standard is available from the Estonian Centrefor Standardisation.
This document is a preview generated by EVS
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 13480-3
June 2017 ICS 23.040.01 Supersedes EN 13480-3:2012
English Version Metallic industrial piping - Part 3: Design and calculationTuyauteries industrielles métalliques - Partie 3 : Conception et calcul Industrielle metallische Rohrleitungen - Teil 3: Konstruktion und Berechnung This European Standard was approved by CEN on 21 June 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T É E U R O P É E N D E N O R M A L I S A T I O N E U R O P Ä I S C H E S K O M I T E E F Ü R N O R M U N G CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13480-3:2017 E
This document is a preview generated by EVS
EN13480‐3:2017(E)
2
Contents
Page
Europeanforeword....................................................................................................................................................10
1 Scope.................................................................................................................................................................12
2 Normativereferences.................................................................................................................................12
3 Terms,definitions,symbolsandunits.................................................................................................13 3.1 Termsanddefinitions................................................................................................................................13 3.2 Symbolsandunits........................................................................................................................................13
4 Basicdesigncriteria....................................................................................................................................15 4.1 General.............................................................................................................................................................15 4.2 Loadings..........................................................................................................................................................15 4.2.1 General.............................................................................................................................................................15 4.2.2 Combinationofloads..................................................................................................................................16 4.2.3 Loadsfordimensioning.............................................................................................................................16 4.2.4 Otherloadstobetakenintoaccount....................................................................................................18 4.2.5 Designconditions.........................................................................................................................................19 4.3 Thickness........................................................................................................................................................22 4.4 Tolerances......................................................................................................................................................25 4.5 Jointcoefficient.............................................................................................................................................25 4.6 Dimensioningofpipingcomponentssubjecttopressure.............................................................26
5 Designstresses..............................................................................................................................................26 5.1 General.............................................................................................................................................................26 5.2 Time‐independentnominaldesignstress..........................................................................................27 5.2.1 Steelsotherthanausteniticsteels.........................................................................................................27 5.2.2 Austeniticsteels............................................................................................................................................27 5.2.3 Nickeland/orchromiumalloysteels..................................................................................................28 5.2.4 Steelscastings................................................................................................................................................28 5.2.5 Additionalrequirementsforsteelswithnospecificcontrol........................................................28 5.3 Time‐dependentnominaldesignstress..............................................................................................29 5.3.1 General.............................................................................................................................................................29 5.3.2 Steels.................................................................................................................................................................29 5.3.3 Nickeland/orchromiumalloysteels....................................................................................................30
6 Designofpipingcomponentsunderinternalpressure.................................................................30 6.1 Straightpipes.................................................................................................................................................30 6.2 Pipebendsandelbows...............................................................................................................................30 6.2.1 General.............................................................................................................................................................30 6.2.2 Symbols............................................................................................................................................................31 6.2.3 Requiredwallthicknesses........................................................................................................................31 6.3 Mitrebends.....................................................................................................................................................32 6.3.1 General.............................................................................................................................................................32 6.3.2 Symbols............................................................................................................................................................32 6.3.3 Effectiveradiusofmitrebend.................................................................................................................33 6.3.4 Multiplemitrebends..................................................................................................................................33 6.3.5 Singlemitrebends.......................................................................................................................................34
EVS-EN 13480-3:2017
This document is a preview generated by EVS
3
6.3.6 Adjacentstraightpipesectionsofmitrebends.................................................................................34 6.4 Reducers..........................................................................................................................................................34 6.4.1 Conditionsofapplicability........................................................................................................................34 6.4.2 Specificdefinitions.......................................................................................................................................35 6.4.3 Specificsymbolsandabbreviations.......................................................................................................35 6.4.4 Conicalshells..................................................................................................................................................36 6.4.5 Junctions‐general........................................................................................................................................37 6.4.6 Junctionbetweenthelargeendofaconeandacylinderwithoutaknuckle..........................37 6.4.7 Junctionbetweenthelargeendofaconeandacylinderwithaknuckle................................40 6.4.8 Junctionbetweenthesmallendofaconeandacylinder..............................................................41 6.4.9 Offsetreducers..............................................................................................................................................43 6.4.10 Specialforgedreducers..............................................................................................................................43 6.5 Flexiblepipingcomponents......................................................................................................................44 6.5.1 General.............................................................................................................................................................44 6.5.2 Expansionjoints............................................................................................................................................44 6.5.3 Corrugatedmetalhoseassemblies........................................................................................................46 6.6 Boltedflangeconnections.........................................................................................................................47 6.6.1 General.............................................................................................................................................................47 6.6.2 Symbols............................................................................................................................................................47 6.6.3 Standardflange.............................................................................................................................................47 6.6.4 Non‐standardflange....................................................................................................................................48
7 Designofendsunderinternalpressure...............................................................................................48 7.1 Dishedends.....................................................................................................................................................48 7.1.1 Symbols............................................................................................................................................................48 7.1.2 Hemisphericalends.....................................................................................................................................49 7.1.3 Torisphericalends.......................................................................................................................................50 7.1.4 Ellipsoidalends.............................................................................................................................................51 7.1.5 Calculationof..............................................................................................................................................52 7.2 Circularflatends...........................................................................................................................................56 7.2.1 General.............................................................................................................................................................56 7.2.2 Symbols............................................................................................................................................................56 7.2.3 Unstayedflatcircularendsweldedtocylindricalshells/pipes...................................................58 7.2.4 Unstayedflatcircularboltedends..........................................................................................................65 7.2.5 Reinforcementsofopeningsinunstayedflatends..........................................................................71
8 Openingsandbranchconnections.........................................................................................................74 8.1 General.............................................................................................................................................................74 8.2 Symbols............................................................................................................................................................74 8.3 Limitations......................................................................................................................................................75 8.3.1 Thicknessratio..............................................................................................................................................75 8.3.2 Openingsinthevicinityofdiscontinuities..........................................................................................77 8.3.3 Typesofreinforcement..............................................................................................................................79 8.3.4 Calculationmethod......................................................................................................................................80 8.3.5 Ellipticalopeningsandobliquebranchconnections.......................................................................80 8.3.6 Reinforcingpads...........................................................................................................................................82 8.3.7 Dissimilarmaterialofshellandreinforcements..............................................................................82 8.3.8 Extrudedoutlets............................................................................................................................................82 8.3.9 Forgedtee........................................................................................................................................................82 8.3.10 Branchesinbendsorelbows....................................................................................................................83 8.3.11 Screwed‐inbranches...................................................................................................................................83 8.4 Isolatedopenings..........................................................................................................................................84 8.4.1 General.............................................................................................................................................................84 8.4.2 Unreinforcedopenings...............................................................................................................................87
EVS-EN 13480-3:2017
This document is a preview generated by EVS
EN13480‐3:2017(E)
4
8.4.3 Reinforcedopeningswithdi/Di<0,8..................................................................................................87 8.4.4 Reinforcedsingleopeningswith0,8<d/D1,0..............................................................................93 8.5 Adjacentopenings........................................................................................................................................93 8.5.1 Unreinforcedopenings...............................................................................................................................93 8.5.2 Reinforcedopeningswithd/D0,8......................................................................................................93 8.6 Designofspecialpipingcomponents....................................................................................................94 8.6.1 CylindricalY‐pieces.....................................................................................................................................94 8.6.2 SphericalY‐pieces........................................................................................................................................95 8.6.3 Triformreinforcedbranches...................................................................................................................96
9 Designofpipingcomponentsunderexternalpressure.................................................................97 9.1 General.............................................................................................................................................................97 9.2 Symbolsandelasticstresslimits............................................................................................................99 9.2.1 Symbols............................................................................................................................................................99 9.2.2 Elasticstresslimits....................................................................................................................................101 9.3 Cylindricalpipes,elbowsandmitrebends.......................................................................................101 9.3.1 Determinationoflengths........................................................................................................................101 9.3.2 Interstiffenercollapse..............................................................................................................................103 9.3.3 Overallcollapseofstiffenedpipes.......................................................................................................105 9.3.4 Stiffenerstability........................................................................................................................................106 9.3.5 Heating/coolingchannels.......................................................................................................................109 9.4 Reducers(conicalshells)........................................................................................................................110 9.5 Dishedends..................................................................................................................................................112 9.5.1 Hemisphericalends...................................................................................................................................112 9.5.2 Torisphericalends.....................................................................................................................................113 9.5.3 Ellipsoidalends...........................................................................................................................................113
10 Designforcyclicloading..........................................................................................................................113 10.1 General...........................................................................................................................................................113 10.2 Exemptionfromdetailedfatigueanalysis........................................................................................113 10.3 Fatiguedesignforcyclicpressure........................................................................................................114 10.3.1 Equivalentfullloadcycles.......................................................................................................................114 10.3.2 Simplifiedfatigueanalysis......................................................................................................................114 10.4 Fatiguedesignforthermalgradients.................................................................................................129 10.4.1 General...........................................................................................................................................................129 10.4.2 Designguidance..........................................................................................................................................129 10.5 Fatiguedesignforcombinedloads......................................................................................................130
11 Integralattachments.................................................................................................................................130 11.1 General...........................................................................................................................................................130 11.2 Allowablestresses.....................................................................................................................................130 11.3 Symbols..........................................................................................................................................................131 11.4 Hollowcircularattachments..................................................................................................................133 11.4.1 Limitations....................................................................................................................................................133 11.4.2 Preliminarycalculations.........................................................................................................................133 11.4.3 Analysisofattachmentsweldedtopipewithafullpenetrationweld....................................135 11.4.4 Analysisofattachmentsweldedtopipewithfilletorpartialpenetrationweld................136 11.5 Rectangularattachments........................................................................................................................136 11.5.1 Limitations....................................................................................................................................................136 11.5.2 Preliminarycalculations.........................................................................................................................136 11.5.3 Analysisofattachmentsweldedtopipewithafullpenetrationweld....................................138 11.5.4 Analysisofattachmentsweldedtopipewithfilletorpartialpenetrationweld................139 11.6 Stressanalysisoftherunpipe...............................................................................................................139 11.7 Shearstressanalysisinattachment....................................................................................................141
EVS-EN 13480-3:2017
This document is a preview generated by EVS
5
11.7.1 Hollowcircularattachments.................................................................................................................141 11.7.2 Rectangularattachments........................................................................................................................141 11.8 Alternativecalculationmethods..........................................................................................................141
12 Flexibilityanalysisandacceptancecriteria.....................................................................................141 12.1 Basicconditions.........................................................................................................................................141 12.1.1 General..........................................................................................................................................................141 12.1.2 Loadingconditions....................................................................................................................................142 12.1.3 Allowablestresses.....................................................................................................................................142 12.2 Pipingflexibility.........................................................................................................................................144 12.2.1 General..........................................................................................................................................................144 12.2.2 Basicconditions.........................................................................................................................................144 12.2.3 Displacementstrains................................................................................................................................144 12.2.4 Displacementstresses.............................................................................................................................145 12.2.5 Stressrange.................................................................................................................................................146 12.2.6 Coldpull........................................................................................................................................................146 12.2.7 Propertiesforflexibilityanalysis........................................................................................................147 12.2.8 Supportingconditions.............................................................................................................................147 12.2.9 Expansionjoints.........................................................................................................................................149 12.2.10Flexibilityanalysis....................................................................................................................................149 12.3 Flexibilityanalysis....................................................................................................................................151 12.3.1 General..........................................................................................................................................................151 12.3.2 Stressduetosustainedloads................................................................................................................152 12.3.3 Stressduetosustainedandoccasionalorexceptionalloads....................................................152 12.3.4 Stressrangeduetothermalexpansionandalternatingloads.................................................153 12.3.5 Additionalconditionsforthecreeprange........................................................................................154 12.3.6 Stressesduetoasinglenon‐repeatedsupportmovement........................................................154 12.3.7 Determinationofresultantmoments................................................................................................155 12.3.8 Alternativemethodforstresscalculation........................................................................................157 12.3.9 Reactions......................................................................................................................................................157 12.4 Fatigueanalysis..........................................................................................................................................157 12.5 Vibration.......................................................................................................................................................157
13 PipeSupports..............................................................................................................................................158 13.1 Generalrequirements..............................................................................................................................158 13.1.1 General..........................................................................................................................................................158 13.1.2 Classificationofsupports........................................................................................................................158 13.1.3 Additionaldefinitions..............................................................................................................................159 13.1.4 Boundaries...................................................................................................................................................161 13.1.5 Pipesupportsweldedtothepipe........................................................................................................163 13.2 Selectionofpipesupports......................................................................................................................164 13.2.1 General..........................................................................................................................................................164 13.2.2 Detaildesignofpipesupports..............................................................................................................165 13.2.3 Supportlocation.........................................................................................................................................166 13.3 Constanthangers/basemounted(pedestal)constantsupports..............................................166 13.3.1 General..........................................................................................................................................................166 13.3.2 Loaddeviationfromcalibratedload..................................................................................................166 13.3.3 Siteadjustmentofthecalibratedload...............................................................................................166 13.3.4 Travelreserve(Overtravel)...................................................................................................................166 13.3.5 Blocking.........................................................................................................................................................167 13.3.6 IdentificationMarking/Nameplate....................................................................................................167 13.4 Variableloadspringhangersandbasemounted(pedestal)variableloadspring
supports........................................................................................................................................................167 13.4.1 General..........................................................................................................................................................167
EVS-EN 13480-3:2017
This document is a preview generated by EVS
EN13480‐3:2017(E)
6
13.4.2 Toleranceonspringrate.........................................................................................................................168 13.4.3 Travelreserve(Overtravel)...................................................................................................................168 13.4.4 Blocking.........................................................................................................................................................168 13.4.5 Nameplate....................................................................................................................................................168 13.5 Rigidstruts...................................................................................................................................................169 13.6 Shockarrestors(shockabsorber,snubber).....................................................................................169 13.7 Slidingsupports..........................................................................................................................................170 13.8 Anchors..........................................................................................................................................................170 13.9 Documentationofsupports....................................................................................................................170 13.10 Markingofsupports..................................................................................................................................170 13.11 Manufacturingofpipesupports...........................................................................................................170 13.11.1Materialrequirements............................................................................................................................170 13.11.2Designtemperaturesforsupportcomponents..............................................................................171 13.11.3Designdetails..............................................................................................................................................172 13.11.4Determinationofcomponentsizes.....................................................................................................173 13.11.5Weldedconnections.................................................................................................................................174 13.11.6Threadedconnections.............................................................................................................................176 13.11.7Additionalrequirementsonsprings..................................................................................................177 13.11.8Designdetailsforrigidstruts...............................................................................................................177 13.11.9Designdetailsforshockarrestors(shockabsorbers,snubbers)............................................178 13.11.10Designdetailsforshockarrestors(shockabsorbers,snubbers)..........................................179
AnnexA(informative)Dynamicanalysis.........................................................................................................180 A.1 General...........................................................................................................................................................180 A.2 Analysisbycalculation.............................................................................................................................180 A.2.1 Seismicevents.............................................................................................................................................180 A.2.2 Rapidvalveclosure...................................................................................................................................184 A.2.3 Flowinducedvibration............................................................................................................................187 A.2.4 Safetyvalvedischarge..............................................................................................................................189 A.2.5 Allowablestresses.....................................................................................................................................192 A.3 Alternativemeansofdesignverification...........................................................................................192 A.3.1 Comparativestudies.................................................................................................................................192 A.3.2 Fullscaletesting.........................................................................................................................................192 A.3.3 Reducedscaletesting...............................................................................................................................192
AnnexB(normative)Moreaccuratecalculationofbendsandelbows.................................................193 B.1 General...........................................................................................................................................................193 B.2 Symbolsandunits......................................................................................................................................193 B.3 Requiredwallthickness..........................................................................................................................194 B.4 Calculation....................................................................................................................................................195 B.4.1 Calculationofwallthickness..................................................................................................................195 B.4.2 Stresscalculation.......................................................................................................................................197
AnnexC(informative)Expansionjoints...........................................................................................................201 C.1 Incorporationofexpansionjointsintopipingsystems................................................................201 C.1.1 General...........................................................................................................................................................201 C.1.2 Typesofexpansionjoints........................................................................................................................202 C.1.3 Designofexpansionjoints......................................................................................................................202 C.1.4 Designingwithexpansionjoints...........................................................................................................203 C.1.5 Analysesandcalculation.........................................................................................................................205 C.1.6 Coldpull.........................................................................................................................................................206 C.2 Maximumspacingforunrestrainedaxiallycompensatedstraightruns...............................206 C.2.1 General...........................................................................................................................................................206 C.2.2 Calculationrules.........................................................................................................................................206
EVS-EN 13480-3:2017
This document is a preview generated by EVS
7
C.2.3 Maximumspacingfordefinedconditions........................................................................................207 C.3 Indicationforthedesignofexpansionjoints..................................................................................209 C.3.1 General..........................................................................................................................................................209 C.3.2 Informationforthesystemanalyst.....................................................................................................209
AnnexD(normative)Flanges...............................................................................................................................210 D.1 Purpose.........................................................................................................................................................210 D.2 Specifictermsanddefinitions...............................................................................................................210 D.3 Specificsymbolsandabbreviations....................................................................................................211 D.4 General..........................................................................................................................................................212 D.4.1 Introduction................................................................................................................................................212 D.4.2 Useofstandardflangeswithoutcalculation....................................................................................212 D.4.3 Bolting............................................................................................................................................................213 D.4.4 Flangeconstruction..................................................................................................................................215 D.4.5 Machining.....................................................................................................................................................215 D.4.6 Gaskets..........................................................................................................................................................215 D.5 Narrowfacegasketedflanges...............................................................................................................216 D.5.1 General..........................................................................................................................................................216 D.5.2 Boltloadsandareas..................................................................................................................................219 D.5.3 Flangemoments.........................................................................................................................................220 D.5.4 Flangestressesandstresslimits..........................................................................................................220 D.5.5 Narrowfaceflangessubjecttoexternalpressure.........................................................................226 D.5.6 Lapjoints......................................................................................................................................................226 D.5.7 Splitringflanges........................................................................................................................................229 D.6 Fullfaceflangeswithsoftringtypegaskets....................................................................................230 D.6.1 Specificsymbolsandabbreviations....................................................................................................231 D.6.2 Boltloadsandareas..................................................................................................................................231 D.6.3 Flangedesign...............................................................................................................................................232 D.6.4 Fullfaceflangessubjecttoexternalpressure.................................................................................233 D.7 Sealweldedflanges...................................................................................................................................233 D.8 Reversenarrowfaceflanges..................................................................................................................234 D.8.1 Internalpressure.......................................................................................................................................234 D.8.2 Externalpressure......................................................................................................................................236 D.9 Reversefullfaceflanges..........................................................................................................................236 D.9.1 General..........................................................................................................................................................236 D.9.2 DesignfollowingmethodofD.5............................................................................................................236 D.9.3 DesignfollowingmethodofD.6............................................................................................................238 D.10 Fullfaceflangeswithmetaltometalcontact..................................................................................240 D.10.1General..........................................................................................................................................................240 D.10.2Specificsymbolsandabbreviations....................................................................................................240 D.10.3Design............................................................................................................................................................241
AnnexE(normative)Designofbranchconnectionsinpipingaccessories.........................................243 E.1 Scope..............................................................................................................................................................243 E.1.1 General..........................................................................................................................................................243 E.2 Reinforcement............................................................................................................................................245 E.2.1 Anglesandareas........................................................................................................................................245 E.2.2 Thefollowingconditionshallbesatisfied:.......................................................................................245 E.3 Flexibilityanalysis....................................................................................................................................246
AnnexF(informative)Testingduringoperationinthecaseofcyclicloading...................................248 F.1 Testingduringoperation........................................................................................................................248 F.2 Measurestobetakenwhenthecalculatedfatiguelifehasbeenreached............................248
AnnexG(informative)Physicalpropertiesofsteels...................................................................................250
EVS-EN 13480-3:2017
This document is a preview generated by EVS
EN13480‐3:2017(E)
8
G.1 General...........................................................................................................................................................250 G.2 Physicalproperties....................................................................................................................................250 G.2.1 Density...........................................................................................................................................................250 G.2.2 Differentialcoefficientoflinearexpansion......................................................................................251 G.2.3 Specificthermalcapacity.........................................................................................................................251 G.2.4 Thermaldiffusivity....................................................................................................................................251 G.2.5 Poisson'sratio.............................................................................................................................................251 G.3 Physicalpropertiesofsteels..................................................................................................................251
AnnexH(normative)Flexibilitycharacteristics,flexibilityandstressintensificationfactorsandsectionmoduliofpipingcomponentsandgeometricaldiscontinuities........................257
AnnexI(informative)Productiontestingofspringsupportsandshockarrestors(shockabsorbers)....................................................................................................................................................267
I.1 Constantloadsupports............................................................................................................................267 I.2 Variablespringsupports.........................................................................................................................267 I.3 Shockarrestors...........................................................................................................................................267
AnnexJ(normative)Typetestingofsupportcomponents........................................................................272
AnnexK(informative)Attachmentofsupportstostructures..................................................................274 K.1 Attachmentofsupportstoconcretestructures..............................................................................274 K.2 Attachmenttometallicstructures.......................................................................................................275 K.2.1 Standardbolts.............................................................................................................................................275 K.2.2 Frictiongripbolts......................................................................................................................................275 K.2.3 Welding..........................................................................................................................................................275
AnnexL(informative)Bucklingoflineartypesupports............................................................................276 L.1 General...........................................................................................................................................................276 L.2 Symbols..........................................................................................................................................................276 L.3 Basic formulae...........................................................................................................................................277 L.4 Allowablecompressivestress...............................................................................................................277 L.5 Bucklinglength...........................................................................................................................................278
AnnexM(informative)Designguidanceforstructuralcomponents.....................................................280 M.1 Lineartypecomponentssubjectedtobending...............................................................................280 M.1.1 General...........................................................................................................................................................280 M.1.2 Supplementaryverificationsforlineartypesupports.................................................................280 M.2 Stabilityofplatetypesupports.............................................................................................................282 M.3 Anchorageplatesorequivalentanchoragecomponents............................................................282 M.3.1 General...........................................................................................................................................................282 M.3.2 Designofsimpleanchorageplates......................................................................................................282 M.3.3 Fixingplateswithstiffeninggussets...................................................................................................283 M.3.4 Loadcalculationsforanchoragesfixedinconcrete......................................................................283
AnnexN(normative)Documentationofsupports........................................................................................284
AnnexO(normative)Alternativemethodforcheckingbranchconnections.....................................286 O.1 Scope...............................................................................................................................................................286 O.2 Symbols..........................................................................................................................................................286 O.3 Designandcheckingofthebranchconnection...............................................................................288 O.3.1 Limitvaluefortheloadduetopressureonlyforstraightpipeswithoutopening............288 O.3.2 Determinationoftheminimumthicknessesunderloadingduetopressureonly............289 O.3.3 Checkingofthethicknessesselectedforthecombinationofpressureloadingand
loadingsduetoexternalloads..............................................................................................................289
AnnexP(informative)Recommendedgasketsforindustrialpiping.....................................................340
EVS-EN 13480-3:2017
This document is a preview generated by EVS
9
AnnexQ(informative)Simplifiedpipestressanalysis...............................................................................342 Q.1 General..........................................................................................................................................................342 Q.2 Simplifiedprocedure................................................................................................................................342 Q.2.1 General..........................................................................................................................................................342 Q.2.2 Specificationofallowablespacingofsupports...............................................................................342 Q.2.3 Checkofelasticity......................................................................................................................................342 Q.3 ExplanatorynotesforTableQ.1...........................................................................................................344 Q.4 Symbols.........................................................................................................................................................346 Q.5 IndicesfL........................................................................................................................................................346 Q.6 ExplanatorynotestoQ.2.2.....................................................................................................................347 Q.6.1 Specificationofallowablespacingofsupports...............................................................................347 Q.7 Conversionoftheallowablelengths...................................................................................................348 Q.7.1 Othersupportconditions.......................................................................................................................348 Q.7.2 Otherparameters......................................................................................................................................348 Q.8 Additionalsingleloads............................................................................................................................349 Q.8.1 General..........................................................................................................................................................349 Q.9 ExplanatorynoteonFigureQ.2............................................................................................................352 Q.9.1 General..........................................................................................................................................................352 Q.9.2 RequiredpipeleglengthL1,forf1fromthenomogram...............................................................354 Q.9.3 RequiredpipeleglengthL2,forf2fromthenomogram..............................................................354
AnnexY(informative)HistoryofEN13480‐3................................................................................................359 Y.1 DifferencesbetweenEN13480‐3:2012andEN13480‐3:2017.................................................359
AnnexZA(informative)RelationshipbetweenthisEuropeanStandardandtheEssentialRequirementsofEUDirective2014/68/EUaimedtobecovered...........................................361
Bibliography..............................................................................................................................................................362
EVS-EN 13480-3:2017
This document is a preview generated by EVS
EN13480‐3:2017(E)
10
Europeanforeword
Thisdocument(EN13480‐3:2017)hasbeenpreparedbyTechnicalCommitteeCEN/TC267“Industrialpipingandpipelines”,thesecretariatofwhichisheldbyAFNOR.
This European Standard shall be given the status of a national standard, either by publication of anidentical text orby endorsement, at the latest byDecember2017, and conflictingnational standardsshallbewithdrawnatthelatestbyDecember2017.
Attentionisdrawntothepossibilitythatsomeoftheelementsofthisdocumentmaybethesubjectofpatentrights.CEN[and/orCENELEC]shallnotbeheldresponsibleforidentifyinganyorallsuchpatentrights.
ThisdocumenthasbeenpreparedunderamandategiventoCENbytheEuropeanCommissionandtheEuropeanFreeTradeAssociation,andsupportsessentialrequirementsofEUDirective(s).
For relationship with EUDirective(s), see informative Annex ZA, which is an integral part of thisdocument.
ThisEuropeanStandardEN13480 formetallic industrialpipingconsistsofeight interdependentandnotdissociablePartswhichare:
Part1:General;
Part2:Materials;
Part3:Designandcalculation;
Part4:Fabricationandinstallation;
Part5:Inspectionandtesting;
Part6:Additionalrequirementsforburiedpiping;
CEN/TR13480‐7,Guidanceontheuseofconformityassessmentprocedures;
Part8:Additionalrequirementsforaluminiumandaluminiumalloypiping.
Although these Parts may be obtained separately, it should be recognised that the Parts are inter‐dependant. As such the manufacture of metallic industrial piping requires the application of all therelevantPartsinorderfortherequirementsoftheStandardtobesatisfactorilyfulfilled.
This European Standard will be maintained by a Maintenance MHD working group whose scope ofworkingislimitedtocorrectionsandinterpretationsrelatedtoEN13480.
EVS-EN 13480-3:2017
This document is a preview generated by EVS
11
The contact to submit queries can be found at http://www.unm.fr ([email protected]). A form forsubmittingquestionscanbedownloadedfromthelinktotheMHDwebsite.Aftersubjectexpertshaveagreedananswer, theanswerwillbecommunicatedto thequestioner.CorrectedpageswillbegivenspecificissuenumberandissuedbyCENaccordingtoCENRules.InterpretationsheetswillbepostedonthewebsiteoftheMHD.
This document supersedes EN13480‐3:2012. This new edition incorporates the AmendmentswhichhavebeenapprovedpreviouslybyCENmembers,and thecorrectedpagesup to Issue5withoutanyfurther technical change. Annex Y provides details of significant technical changes between thisEuropeanStandardandthepreviousedition.
Amendments to this new edition may be issued from time to time and then used immediately asalternativestorulescontainedherein.
According to the CEN‐CENELEC Internal Regulations, the national standards organizations of thefollowing countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,Croatia, Cyprus, CzechRepublic,Denmark,Estonia, Finland, FormerYugoslavRepublic ofMacedonia,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,Netherlands,Norway,Poland,Portugal,Romania,Serbia,Slovakia,Slovenia,Spain,Sweden,Switzerland,TurkeyandtheUnitedKingdom.
EVS-EN 13480-3:2017
This document is a preview generated by EVS
EN13480‐3:2017(E)
12
1 Scope
This Part of this European Standard specifies the design and calculation of industrialmetallic pipingsystems,includingsupports,coveredbyEN13480.
2 Normativereferences
The following documents, inwhole or in part, are normatively referenced in this document and areindispensable for its application. For dated references, only the edition cited applies. For undatedreferences,thelatesteditionofthereferenceddocument(includinganyamendments)applies.
EN1515‐2:2001, Flanges and their joints— Bolting— Part 2: Combination of flange and boltingmaterialsforsteelflangesPNdesignated
EN1515‐3:2005,Flangesand their joints—Bolting—Part3:Classificationofboltmaterials for steelflanges,Classdesignated
EN1515‐4:2010,Flangesandtheirjoints—Bolting—Part4:SelectionofboltingforequipmentsubjecttothePressureEquipmentDirective97/23/EC
EN 1591‐1:2013, Flanges and their joints— Design rules for gasketed circular flange connections—Part1:Calculationmethod
EN1591‐2:2008, Flanges and their joints— Design rules for gasketed circular flange connections—Part2:Gasketparameters
EN1993(allparts),Eurocode3:Designofsteelstructures
EN10204:2004,Metallicproducts—Typesofinspectiondocuments
EN10216‐2:2013,Seamlesssteeltubesforpressurepurposes—Technicaldeliveryconditions—Part2:Non‐alloyandalloysteeltubeswithspecifiedelevatedtemperatureproperties
EN13445‐3:2014,Unfiredpressurevessels—Part3:Design
EN13480‐1:2017,Metallicindustrialpiping—Part1:General
EN13480‐2:2017,Metallicindustrialpiping—Part2:Materials
EN13480‐4:2017,Metallicindustrialpiping—Part4:Fabricationandinstallation
EN13480‐5:2017,Metallicindustrialpiping—Part5:Inspectionandtesting
ENISO5817:2007,Welding— Fusion‐welded joints in steel, nickel, titanium and their alloys (beamweldingexcluded)—Qualitylevelsforimperfections(ISO5817:2003,correctedversion:2005,includingTechnicalCorrigendum1:2006)
EVS-EN 13480-3:2017
This document is a preview generated by EVS