dvr quick operating instructions - kotajogja.netkotajogja.net/download/c c t v/dvr cctv/standalone...

19
Quick Operating Instructions v1.0 DVR Quick Operating Instructions Customer Service Hotline400-888 7918 Domain Name Access: Chinese Address: http://www.dvrserver.net:100 English Address: http://www.dvrserver.net:99 Cloud Service Address: http://www.vssweb.net Mobile Software: IOS, Android Mobile phone monitoring software name "IMSeye" 1

Upload: voquynh

Post on 16-May-2018

259 views

Category:

Documents


4 download

TRANSCRIPT

Page 1: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

DVR Quick Operating Instructions

Customer Service Hotline:400-888 7918

Domain Name Access: Chinese Address: http://www.dvrserver.net:100

English Address: http://www.dvrserver.net:99

Cloud Service Address: http://www.vssweb.net

Mobile Software: IOS, Android Mobile phone monitoring software

name "IMSeye"

1

Page 2: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0 Thank you for choosing our embedded DVR product, please carefully read the following contents before you use the product: Precautions:

The following contents describe the correct use method of the product as well as the measures to prevent danger or

property loss, please be sure to observe the requirements.

Please operate the DVR in the allowable temperature and humidity range.

Do not install the DVR in damp, dusty or sooty locations.

Please install the product horizontally and pay attention to preventing the product from falling.

Install it in a well ventilated place, and do not block the vents of the product.

Do not place any containers filled with liquids or other devices on the product.

Do not disassemble the product randomly.

Please choose the hard disk that is recommended by hard disk manufacturers and suitable for the embedded DVR.

The real product shall prevail, and this instruction is for reference only.

There may be technical inaccuracies or typographical errors in this product manual.

The products or procedures described in this product manual may be subject to improvement or update at any time

without further notice.

The screenshots in this product manual are not those of the same model, for illustrative purpose only.

If you have any questions or need the latest procedures and supplemental documentation, please contact the

company’s after-sale service department. Note: Full-featured DVR is taken as an example, serving as a reference for other models. I. Host Connection and Start

1.1 Host internal SATA hard disk does not support hot plugging, please connect and fix the hard disk connecting line before starting the machine.

1.2 Video output on DVR is connected to the video input interface of the monitor BNC (or the display VGA), turn on the monitor or the display.

1.3 Connect the power supply to the power interface on the DVR, the device starts and enters into the system. II. System Login 2.1 Connect the mouse, click the right mouse button, select the main menu; the user login dialog box pops up. Select the user login (administrator user name: admin; Password: 123456; ordinary user: user; Password: 123456), the user password and user permission can be modified in the user administration, and it can also add new users. 2.2 The machine starts and automatically records. Under preview mode, users can click the right mouse button and select "Manual recording" for selection configuration.

2

Page 3: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0 2.3 The tree diagram of operation menu is as follows:

Main menu

Configuration management

Maintenance management

Peripheral management

Storage management

Turn off the device

System setting

Channel

configuration

Netw

ork

configuration

Alarm

configuration

User

administration

Abnorm

ality

configuration

Log information

Online user

Version Inform

ation

Restore default

Stream statistics

Autom

atic m

aintenance

Output m

ode

PTZ configuration

Alarm

output

Serial port configuration

Autom

atic polling

confi guration

Modify the channel nam

e

Output resolution

Hard

disk m

ana gement

Video backup

User logoff

Restart the device

Turn off the device

Channel setting

Record plan

Basic setting

Netw

ork state

Advanced

confi guration

Dom

ain name D

DN

S

Netw

ork transm

ission

Email

PPPOE

FTP

IP ermission

DV

R SERV

ER

Local external alarm

Video detection alarm

Port modification

,UPN

P

Modify user passw

ord

Modify user perm

issions

Add or delete users

Add or delete user group

P2P

Video inquiry

3

Page 4: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0 2.4 Record Plan Settings: Click the right mouse button → "Main Menu" → "Configuration Management" → "Channel Configuration" → "Record Plan", click the configuration to set. As shown below:

[Channel] Select the channel number. The menu uses green, yellow and red to display the time plan of the three kinds of recording status: Regular, MD and Alarm of the corresponding channels within a week, which can be modified by clicking the [Configuration] corresponding to each date. [Copy] Copy the configuration to other channels. Click [Configuration] [Time Period] Set the recording time period, there are six time periods per day to choose from. [Regular] After selected, it is valid for regular recording. [MD] After selected, it is valid for MD recording. [Alarm] After selected, it is valid for alarm recording. III. Local Alarm Configuration

3.1 Local alarm configuration: Click the right mouse button → "Main Menu" → "Configuration Management" → "Alarm Configuration" , as shown below:

4

Page 5: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

[Alarm Input Channel No.] Select the alarm input channel. [Enable] Select “Enable” to control the ON and OFF of alarm input. [Type] Two selection modes: Normal Open and Normal Close. [Copy] Copy the configuration to other channels. [Processing] Click “Processing” and enter into the setting interface of alarm processing, the interface is shown in Figure 4-16. [Arming Time period] The menu will display the arming time, entering into the edit plan can configure the arming time of each day. [Linkage Set] Click “Enable” to start the linkage of [Recording Channel Linkage], [PTZ Linkage], [Polling] and [Capture], and select the linkage channels. [Processing] Click “Enable” to start the [Alarm Output], [Screen Prompt], [Send Email] and [Beep]. Alarm cancel delay time can be set as 10-300s. Ⅳ. Network Settings 4.1 Enter into the network configuration: Click the right mouse button → “Main Menu”→ “Configuration Management”→ “Network Configuration” 1. To automatically get the IP address, tick the [automatically get the IP address], automatic search IP function (i.e.

DHCP). When DHCP is opened, IP/Mask /Gateway can’t be set. If current DHCP becomes effective, then the IP/Mask/Gateway displays that the value obtained by DHCP can be found in Network State.

2. View the got IP address in Network State.

5

Page 6: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

3. After successfully getting the IP address, click “Advanced” → “DDNS” to select DVR SERVER in “DDNS Type”

column, tick “Enable” and click “App.” for confirmation. After about 1 minute, we will see that the ID column displays the exclusive ID number of the machine. Write down the ID.

4. Enter into the settings of network transmission capacity, port and main playing, modify the port number of DVR, and

the TCP, HTTP and port numbers range from 1 to 655,35. The way to use UPNP automatic forwarding port is as follows:

4.1 Initiate the UPNP function of the router: take TP-link as an example: enter into the router → “Forwarding Rules” → Initiate “UPNP Settings”, as shown below:

Note: The factory default ports of DVR include HTTP port 80 and TCP port 800. If there is more than one DVR under the same router, please modify the port of each DVR, in order to ensure that there is no repeated DVR port. Otherwise, it will forward with the last IP address of the same port number, i.e. the router will only map the last added IP address.

Ⅴ. IE Access Method

5.1 The IE controls are set in the following ways.

5.1.1 Right click the browser icon , and click “Attribute” in the pop-up drop-down list to pop up the dialog box:

6

Page 7: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

Click the “Security” tab

5.1.2 Set the seven items related to ActiveX as Enable or Prompt in the “Security Settings” interface, as shown below:

7

Page 8: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

5.2 Computer IE access is as follows:

5.2.1 Taking the setting demonstration provided in the item 4 of Network Settings as an example: (note: For remote

access of users, please subject to the parameters set by the users themselves) LAN access address: http://192.168.2.105:80 WAN access addresses: Chinese address: http://www.dvrserver.net:100 English address: http://www.dvrserver.net:99 In case of LAN access, enter the machine’s ID number into the pop-up input box, as shown below:

Password: 123456 Ordinary User: user Password: 123456 Administrator User Name: admin

Click to get IP, automatically go to the DVR login interface.

Note: As to client access, please refer to the client access settings guidance document in the form of CD, it contains detailed software introduction and description.

5.3 Cloud Service Access

5.3.1 DVR host settings: Right click → Main Menu → Configuration Management → Network Configuration → “Advanced” to find out the VVNAT option, as shown below:

The cloud service function will be initiated by default when the machine is started

Enter into the VVNET option, as shown below:

8

Page 9: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

Bear this ID in mind, because it will be used in cloud service connection

Description:

1. Device ID: Cloud service connection ID number. Use this ID for connection in cloud service IE. Please bear this ID number in mind.

2. The service password is the user password of the machine: The factory default is A0Yzk5 3. Note: The ID number of each device is different, so please refer to the ID number shown in the device;

as to the password, please pay attention to the capital and small letters. 5.3.2 Enter the cloud service address http://www.vssweb.net into the IE address bar Enter into the cloud IE interface as shown below:

Select “Device login” and enter the ID number in DVR Host Advanced →VSS Cloud Service into the “Serial number” column

The user password is the DVR host password: factory default: AD0h18 (the actual password shall be subject to that displayed by the machine)

Description: 1. Enter the device ID number in the DVR into the “Serial number” column: such as ID number 0f004ca1 2. Password: factory default: please subject to that displayed by the machine (Both the factory default ID

and password of each device are different; pay attention to the capital and small letters of the password) 3. After completing the input, click “Login” to enter into the monitoring interface. 4. User login: User can register an account to conduct centralized management for multiple devices. 5. When registering an account, it is required to fill in the E-mail in use to activate the account, otherwise

9

Page 10: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

the account can not be activated. Some electronic mailboxes may treat the activation mails as junk ones, so please find in the junk e-mails.

5.3.3 Enter into the monitoring interface as shown below:

①.Channel selection zone: Select the channel to be monitored, behind the channel, click the drop-down arrow to select the stream to be monitored ②. PTZ Control Zone

③. Color adjustment, other configurations

④. Split screen ⑤. Local recording, electronic magnification, capture, sound monitoring, monitoring turnoff ⑥. System configuration: remotely set the parameters of DVR, as shown below:

10

Page 11: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

1.4 Record Search: remote playback of record data and download, as shown below:

①. Select the record type ②. Select the start time and end time of the record playback. ③. Click “Search” and the search results will be displayed in the list (the maximum number of

lists is 100). ④. Select the time period to be played and click “Play” to return to the monitoring interface for

playing. green indicates that the current channel is remote playback;

yellow indicates that the current channel is on-site monitoring.

⑤. Clicking “Download” can download the record data of the DVR host to the computer.

11

Page 12: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

5.4 CMS Connection

5.4.1 After installing the CMS client, double click to open it

5.4.2 Click “Settings” on the lower right corner after entering into the interface 5.4.3 Click Device Configuration 5.4 4 Click “Add” on the top left corner 5.4.5After clicking this option, modify the Login Type to P2P

login 5.4.6 Device Name: Any

Serial NO: enter the device ID (device ID in the P2P, such as 0f1008b6) Password: The control password in the P2P。

7. After saving, click the lower right corner to exit, and then click the Channel List on the top right corner and double click the

Channel Connection.

VI. Mobile Client Monitoring

This section mainly describes the instructions for installation and use in Android and IOS phones.

6.1 For IOS mobile software, please log in IOS official application search software “IMSeye” to download and install it. 6.2 Android can be installed by using the attached CD and copying it to computer, or searching “IMSeye” in Google

Market. 6.3 It can also enter the https://play.google.com/store into the computer IE address bar to search “IMSeye” and download

Android. 6.4 The Essential Conditions for Mobile Phones:

6.4.1 IOS software must be Version 4.1 or newer, and support iPhone 3, iPhone 3S, iPhone 4, iPhone4S, iPhone5, iPAD 2, iPAD3 and iPAD 4.

6.4.2 Android mobile phone software version: Android version 1.5 or newer.

6.5 Main Functions: 6.5.1 Browse DVR monitor screen in real time, and support four-screen monitoring. 6.5.2 Support PTZ control (the front end should be controllable dome or PTZ) 6.5.3 Support mobile phone recording and local video playback. 6.5.4 Support mobile phone capture.

6.6 Mobile Phone Monitoring Software Instructions Here take IOS software as an example; run this program and enter into the main interface: as shown below

12

Page 13: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

Icon Name Description

Live View

Enter into the Live View screen for PTZ control and other operations

Device List Add or delete device list

Photos Capture albums, view the captured photos

Local Playback Mobile phone video search and playback

About About software description

2.1) To add new devices, enter into the interface as shown below:

13

Page 14: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

DeviceName: Device Name Connection:address、P2P Address: Please enter the device IP address or DDNS Command Port: Please enter the device data port number: default 8000 User Name: Enter the DVR user name Password: Please enter the user name password Max Channel: Please enter the maximum channel number of current device.

7 Click “Live View” to enter into the program, as shown below

Icon Name Description

Password: 123456 User

Factory default user name: admin LAN / DDNS input icon

Password: 123456 Factory default user name: 0f038c18 P2P input icon

14

Page 15: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

Settings Button Enter into device management to modify, add or delete devices

Alarm Prompt

In case of alarm from current monitoring channel, send alarm prompt, and the icon becomes red.

Recording Button

Recording button, pressing this button can enter into the recording state

Capture Button Capture channel images

、 Play/Stop

Play when there is no channel monitoring, and Stop when there is channel monitoring.

Channel Display

Switching Switching button for the number of display channels

PTZ Control Click it to enter into PTZ Control.

Add Monitoring Channel

Double click this button to enter into device management and add monitoring channels

Channel Selection Channel button, conduct channel switching in the single screen of

the split screen

8 Enter into the Device Management, as shown below:

8.1 Double click the device, it will display the device channel

8.2 Add new devices

8.3 Delete devices

9 PTZ Control Under monitoring, click PTZ Control, as shown below:

15

Page 16: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

: Up and Down, control the PTZ to move up and down

: Left and Right, control the PTZ to rotate left and right

:Zoom in and Zoom out, control PTZ zoom

:Focusing increase and decrease

: Aperture zoom in and zoom out

Note: For mobile phone monitoring, QCIF and CIF monitoring are recommended

Frame rate adopts 5-15 frame Stream adopts rated stream of 62-256.

VII. Email Configuration Description

7.1 Enter into the【Main Menu】-【Configuration Management】-【Network Management】-【Advanced】-【Email】,the

configuration interface is shown as below:

16

Page 17: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

【SMTP Server】: It must be corresponding to the Email in use;

【Port】: Email server communication port;

【User Name】: Email name;

【Password】: Email password;

【From】: Email name;

【Title】: Email title;

【Receiver】: Target Email, maximum 3 receivers at present;

【SSL】: SSL encryption Enable.

【Event Interval】: The time interval between two Emails. (Default 5s)

There are two types of Emails: One is text description, the other is picture description.

In【Main Menu】-【Configuration Management】-【Alarm Configuration】, tick the function of Send Email in the

“Processing”,

In the 【Main Menu】-【Configuration Management】-【Alarm Configuration】, initiate the Capture Enable under the

corresponding alarm functions, it will send the Email containing picture, otherwise it will send the Email of text description;

Common Email servers and ports:

Yahoo: smtp.mail.yahoo.com 25 Regular Email sending;

smtp.mail.yahoo.com 465 SSL encrypted Email sending;

126: smtp.126.com 25 Regular Email sending;

163: smtp.163.com 25 Regular Email sending;

Gmail: smtp.gmail.com 465 (Only support SSL encrypted Email sending);

The above types of Email are for reference only; for the servers and ports etc. corresponding to the other Emails, users may log

in the corresponding Email system for inquiry.

7.2. User name password error: Check whether the Email information is correct;

17

Page 18: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

7.3. Port error, for example: SSL Enable is initiated, but the port does not support. Therefore, be sure to check the port

carefully;

7.4. The recipient E-mail does not exist or has error;

7.5. E-mail Enable is not initiated;

7.6. Email server is busy, affecting Email sending.

VIII. Common Troubleshooting

The device can not be started or constantly restarted Possible causes: 1. DVR upgrade error, please remove the hard disk to restore the factory default. 2. DVR motherboard failure, please contact the supplier for repair. 3. Hard disk failure, please replace the hard disk. PTZ can not be controlled Possible causes: 1. RS-485 interfaces cable is connected incorrectly, A and B ports are reversely connected. 2. The settings of PTZ decoder type, protocol, baud rate and address bit are incorrect. 3. RS-485 bus connects too much PTZs, with signal reflex, it is necessary to connect in parallel with a resistor of 120Ω

remotely. 4. The RS-485 interface of the motherboard is damaged. The preview images of DVR are blurred Possible causes: The format of video input formats are not matched, if the camera is NTSC format, while the DVR adopts PAL format, then the preview images will be blurred. The playback images of DVR are blurred or no video is available Possible causes: 1. Program reading error, please try to restart the DVR. 2. Hard disk data error, please test the hard disk, and replace the hard disk if it is damaged. 3. DVR hardware failure, please contact the supplier. DVR can not be connected via network Possible cause: 1. Please check whether the physical network connection is normal. 2. Please check the DVR network parameter configuration. 3. Please check whether there is IP conflict within the network. The downloaded or backup video can not be played normally Possible causes: 1. The player is not installed correctly. 2. The backup U disk or mobile hard disk file system error. 3. No graphics acceleration software of version DX8.1 or newer is installed. Internet Explore Crash Possible causes: In case of IE browser crash during access, please close it and perform the following operations in “Tool” option.

IE option

Internet Explore 9.0 Accesses Possible causes: If using Internet Explore9.0 or newer versions for DVR access, please open the compatibility view mode, as shown below:

18

Page 19: DVR Quick Operating Instructions - kotajogja.netkotajogja.net/Download/C C T V/DVR CCTV/Standalone DVR H.264 S1004...Quick Operating Instructions v1.0 DVR Quick Operating Instructions

Quick Operating Instructions v1.0

IX. Hard Disk Calculation and Maintenance

Hard Disk Capacity Calculation Reference

If the DVR is initially installed, please first check whether the hard disk is installed. The capacity size of the hard disk itself DVR has no limit on the single hard disk capacity, please select according to the requirements of video saving time. Selection of the total capacity The computing formula of hard disk capacity: Total hard disk capacity (MB)=Number of channels ×required time (Hour) × Occupied hard disk capacity per hour (MB/hour)

Note: for the capacity of the hard disk purchased on market, 1GB=1000MB, not the theoretical 1GiB=1024MiB, therefore, in 【Hard Disk Management】→【Basic Configuration】, the displayed capacity is less than the nominal value of the actual hard disk. When DVR adopts the fixed-rate encoding mode, the estimations for the file size generated per hour are shown in the following table:

Stream Size

(Max bit rate) File Size

Stream Size

(Max bit rate)

rate)

File Size

Stream Size

(Max bit rate)

rate)

File Size

96k 42M 320k 140M 896k 393M

128k 56M 384k 168M 1.00M 450M

160k 70M 448k 196M 1.25M 562M

192k 84M 512k 225M 1.50M 675M

224k 98M 640k 281M 1.75M 787M

256k 112M 768k 337M 2.00M 900M

Video file size When DVR adopts the variable-rate encoding mode, the file size generated per hour varies greatly, please refer to the actually generated video file size.

* The CD contains detailed instructions for users’ reference.

19