duradek detail drawings collection€¦ · radek inside perimeter detail: acrylic latex adhesive @...
TRANSCRIPT
dura
dek
dura
dek
dura
dek
dura
dek
CURB DETAIL - TIE-IN TO ROOFING MEMBRANE
DURADEK LTD.ALL ASSEMBLIES OS-16
31/01/19
dura
dek
dura
dek
INSIDE PERIMETER DETAIL: ACRYLIC LATEX ADHESIVE @ FIELD AREA OF MEMBRANE
DURADEK LTD.ALL ASSEMBLIES IS-01-ALT ‘A’
13/03/19
Cladding min 2" clearance from deck surface
Air/moisture barrier-overlap membrane min 2"
Duradek membrane fully adhered 6" min up wall sheathing
Inside edge flashing (opt)
Field of membrane bonded with acrylic latex adhesive
���������������������������������������������� ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
dura
dek
INSIDE PERIMETER DETAIL: CONTACT ADHESIVE @ FIELD AREA OF MEMBRANE
DURADEK LTD.ALL ASSEMBLIES IS-01-ALT ‘B’
13/03/19
Note: Urethane caulking trowelled into corner not required if the July 25% dry bulb temperature does not exceed 29 C (84.2° F)
Fastener Options supplied by Duradek are Color Coated Screws or Painted Ring Shank Nails
���������������������������������������������� ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
dura
dek
dura
dek
dura
dek
FLAT PVC ROOF TIE-IN TO STEEP ROOF
DURADEK LTD.ALL ASSEMBLIES IS-10
04//02/19
NOTE: • Duradek membrane to be separated from non-compatible roofing products or accessories with metal flashing.
• Steep roofing suppliers to confirm their compatibility with a PVC roof membrane.
Duradek membranePlywood sheathing
Steep/shingled roofingBuilding paperMetal flashingDuradek membranePlywood sheathing
8” to first thru fastener
EIFS - WITH RAISED TRIM
DURADEK LTD.
2"
(Hei
ght
of m
embr
ane)
6"
(Hei
ght
of m
etal
insi
de fla
shin
g)
8"
(Hei
ght
of E
IFS R
emov
al)
1
0"
(Not
e: A
ll di
men
sion
s ar
e m
inim
um)
Existing EIFS System
New aesthetic band(by others)
Existing weather resistive barrier (WRB)
Cont. WRB tie-in lapped onto bare metal & apply cont. bead of caulking @ top of membrane
NOTE: WRB tie-in can lap onto PVC Membrance if compatible
Remove 10" of existing EIFS - Leave WRB intact
Duradek membrane bonded to 1-½" x 8" 24 GA Galv Metal inside flashing(Fastened to structural elements)
ALL ASSEMBLIES IS-1104/03/19
���������������������������������������������� ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
EIFS - WITH REMOVABLE TRIM
DURADEK LTD.
[ ]
Existing EIFS system
Seal cut edge with EIFS WTPF base coat
Compatible sealant, closed cellbacker rod c/w weep tubes @24" O.C
Prefinished metal flashing - Set into cont. bead of caulking
Existing weather resistive barrier (WRB)
Duradek membrane bonded to 1-½" x 8" 24 GA galv. metal inside flashing (fastened to structural elements)Removeable trim board with countersunk fasteners - plugged
Remove 10" of existing EIFS - leave WRB intact
NOTE: Non absorbative products like metal or plastic trim boards can extend to deck level
2"
(Hei
ght
of m
embr
ane)
6"
(Hei
ght
of m
etal
insi
de fla
shin
g)
8"
(Hei
ght
of E
IFS R
emov
al)
10"
(Not
e: A
ll di
men
sion
s ar
e m
inim
um)
Cont. WRB tie-in lapped onto bare metal & apply cont. bead of caulking @ top of membrane
NOTE: WRB tie-in can lap onto PVC Membrance if compatible
ALL ASSEMBLIES25/03/19
IS-12
���������������������������������������������� ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
29/08/07
1) Use drain body astemplate to mark 8 1/8”dia flange recess area ¢er of drain
2) Cut 6 1/2” dia hole
3)Router recess so drain flange willsit flush with decksurface
4) Fasten drain body with (3) flush fittingStainless Steel orHot DippedGalvanized screws(not supplied)
5) Optional: if drain is not blocked under - neath: drill / countersink & install (3) additional SS or HDG screws(not supplied)
6) Install membrane,cut 3” dia hole(centered), cutpatches atclamping flangefastening points
7) apply cont. bead of approved urethanecaulking at clamping flange seating area
8) Install retainerclamping flangewith (3) screws(supplied)
9) Install grate with (2)screws (supplied)
Note: 2” (51) ABS body will accept 2” (51) pipe size, NH (MJ) outlet
WDD -1 DRAIN INSTALLATION PROCEDURE
4) Scallop 2” x 6”blocking to accomodate drain body
5) Blocking to spanbetween joists. End fasten thru joists with 3x#10x3” SS WS at each end
12) Install grate with (2)screws (supplied)
Note: 2” (51) ABS body will accept 2” (51) pipe size, NH (MJ) outlet
11) Install retainerclamping fl angewith (3) screws(supplied)
10) Apply cont. beadof approved urethanecaulking at clampingfl ange seating area
9) Install membrane,cut 3” dia hole(centered), cutpatches atclamping fl angefastening points
6) Pre-drill additional 3 x pilot holes in drain fl ange, centeredbetween existing holes
7) Fasten WDD-1 with 6x #8 x 1½” SS WS
8) Lightly grind top of drain fl ange
1) Use drain body astemplate to mark8 1/8” dia fl ange recess area & center of drain
2) Cut 6 ½” dia hole
3)Router recess sodrain fl ange will sit fl ush with deck surface
WDD -1 DRAIN INSTALLATION PROCEDURE
NOTE:_
DRAIN DETAIL- PVC COATED DECK DRAIN
Duradek I membrane hot air welded to drain body flange
4' into bowl. Apply bead of
urethane caulking at
cut edge of membrane.
Pv'C coated drain
cover c/w flathead screws
2% Slope
AS A SUPPLIER Cf FINISHED PRODUCT ONLY, DURADEK LTD. DOE5 NOT ASSUME RESPONSIBILITY � ERRORS N DESIGN, ENGINEERING, CR DIMENSIONS. THE ARCHITECT. ENGINEER, SPECIFIER, CONTRACTOR CR OIA!NERS' REPRESENTATIVE MUST VERIFY ALL
DIMENSIONS, SIZES t SUITABILITY a= DETAILS.
DURADEK LlD. CANADA
UNITED STATES
Bu�. (604) 591-5594
Bu�. (81G} 421-5830
Fox, (604) 59 I -3 I 00
Fox. (816) 421-2924
SYSfEM:
,AJ.l A55EMBLIE5
DATE. 3 I /08/04 R.EV. DATE. 3 I /07 / I 8
DRAWING No.
DR-02
For technical information including drainage charts, visit the manufacturer’s website: http://precisionmetals.ca/alum-vinyl-deck-drains/
Installation Notes:• Drain to be countersunk into plywood deck
approximately 1/8".• Drain body is attached to plywood with 6 - 10 x
?" wood screws (nic). Countersink screw heads with 3/8" high speed countersink drill bit (nic). File off burs (on back side) created from drilling process.
• Attach drain body to drain pipe with “M-J” coupling (nic). Coupling available in stepped sizes for attachment to both larger and smaller diameter drain pipes. (By others)
• Duradek deck membrane is hot air welded to entire PVC coated drain body flang and then into bowl. Avoid glue on back of membrane at drain location. (Glue can be scraped off PVC backed membranes only with nozzle of hot air gun).
• Apply bead of urethane caulking at cut edge of membrane in bowl
• Install drain cover with (3) screws supplied.
PVC Coated Deck Drain
DRAIN DETAIL - ALUMINUM DECK DRAIN
DURADEK LTD.ALL ASSEMBLIES DR-02 - Alt A
22/05/19
Installation Notes:
- Drain to be countersunk into plywood deck approximately 1/8"
- Drain body is attached to plywood with 6 x #8 x 1 ½” screws (or roofing nails).Countersink screw heads with 3/8" high speed countersink drill bit (nic). File off burrs(on back side) created from drilling process.
- Attach drain body to drain pipe with “M-J” coupling (nic). Coupling available instepped sizes for attachment to both larger and smaller diameter drain pipes.(By others)
- Apply bead of urethane caulking at cut edge of membrane bowl.
- Install drain cover with (3) screws supplied.
1 piece spun aluminum bowl
1/4-20x3/4" Stainless steel machine screw
Aluminum strainer
8-32x1/2" Stainless steel machine screw Clamping ringInsert ring
Bead of urethane caulking at cut edge of membrane
Duradek membrane2% slope
���������������������������������������������� ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
DRAIN DETAIL - PVC COATED ALUMINUM DECK DRAIN
DURADEK LTD.ALL ASSEMBLIES DR-02 - Alt B
22/05/19
Installation Notes:
- Drain to be countersunk into plywood deck approximately 1/8"
- Drain body is attached to plywood with 6 x #8 x 1 ½” screws (or roofing nails).Countersink screw heads with 3/8" high speed countersink drill bit (nic). File off burs(on back side) created from drilling process.
- Attach drain body to drain pipe with “M-J” coupling (nic). Coupling available instepped sizes for attachment to both larger and smaller diameter drain pipes. (Byothers)
- Duradek deck membrane is hot air welded to entire PVC coated drain body flang andthen into bowl. Avoid glue on back of membrane at drain location. (Glue can bescrapped off PVC backed membrane only with nozzle of hot air gun).
- Install drain cover with (3) screws supplied.
1 piece spun aluminum bowl
1/4-20x3/4" Stainless steel machine screw
Aluminum strainer
8-32x1/2" Stainless steel machine screw Clamping ringInsert ring
Duradek membrane2% slope
���������������������������������������������� ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
CONCRETE DRAIN WITH SURFACE MEMBRANE CLAMP
DURADEK LTD.DURADEK ULTRA DR-05
Note: Membrane clamped and caulked between strainer and body extension.We recommend the use of Watts FD-100-FC floor drain with surface membrane clamp for concrete deck applications.For more information see Techtalk 165, or visit the manufacturer’s website:http://media3.wattswater.com/ES-WD-FD-100-FC.pdf
17/04/18
* Not for Tiledek Applications
dura
dek
CLASS `A' ROOF COVERING ASSEMBLY
DURADEK LTD.
RAINWATER LEADER (RWL) THRU DECK DETAIL
DURADEK LTD.
‘”
dura
dek
dura
dek