dual monitor desk mount
TRANSCRIPT
Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002k
[email protected] www.vivo-us.com 1-800-371-5654
SKU: STAND-V002K
2 3
ASSEMBLY STEPS
STEP 1
PACKAGE CONTENTS
TOOLS NEEDED
Phillips Screwdriver
A (x2)Arm
B (x1)Clamp
C (x1)Clamp Cover
D (x2)VESA Plate
E (x1)Pole
F (x1)Cable Clip
G (x2)Thumbscrew
H (x3)Bolt
K (x1)4mm Allen Key
L (x1)6mm Allen Key
OPTION A: Clamp InstallationAdjust clamp (B) height according to thickness of desktop. Attach clamp cover (C) to clamp (B). Secure pole (E) to clamp (B) using three bolts (H). Tighten using 4mm Allen key (K).
I (x1)Support Plate
J (x1)Base
M-A (x8)M4x12
M-B (x8)M4x16
M-C (x8)M5x12
M-D (x8)M5x16
M-E (x8) D5 Washer
M-F (x8)Spacer
35-8
0mm
10-4
5mm
C
B
K
H
E
NOTE: SOME HARDWARE MAY NOT BE USED
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNINGSERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARDSMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
17.6 lbs(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.Failure to do so may result in serious injury.
PER ARM
4 5
STEP 1 (Continued)OPTION B: Grommet Base InstallationFor grommet hole attachment, disassemble clamp (B) using 6mm Allen key (L) and a Phillips screwdriver. Attach base (J) to pole (E) through ⅜” (10mm) grommet hole in desktop. Secure using bolt from clamp (B) and plate (I).
STEP 3Adjust arm (A) to desired height. Tighten using 6mm Allen key (L).
STEP 2Slide cable management clip (F) over top of pole (E). Adjust bolt on monitor arm (A) to slide over top of pole (E) as shown in diagram.
STEP 4
Attach VESA plate (D) to the back on monitor using bolts (M-A, M-B, M-C, M-D) and washers (M-E). For curved monitors, spacer (M-F) may be required.
M-E
M-AM-C
M-E
M-BM-D
M-F
D
I
0-40mmJ
F
A
L
L
6 7
STEP 5 STEP 7Adjust tension in arm and angle of monitor using 6mm Allen key (L). Clockwise reduces tension, counterclockwise increases tension. The tension should be just enough to hold your monitor in place without lifting itself up.
STEP 6
Slide VESA plate (D) over bracket on arm (A). Secure using thumb screw (G). Remove bottom covers from arm (A).
Run cables through bottom of arm (A). Re-attach covers.
G
Last Updated: 12/11/2018
If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at: www.vivo-us.com.
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
[email protected] www.vivo-us.com 1-800-371-5654