dsl-3011a user manual
TRANSCRIPT
-
8/13/2019 DSL-3011A User Manual
1/43
Profile
ThankyouforusingDSL3011AADSLTester.
This user manual is composed by instruments function
introduction, installation,wiring,operationprocedureandanswers
ofinstrumentquestions.Toensureyoureasyoperation,pleaseread
this user manual carefully before using and store it in safe and
convenientplaceforquickfindingofproblems.
Notice:
Kindlynoticethatthefutureupdatingoffunctionand
performancecannotbeincludedintheusermanual. Tomakethemanualbetter,ifyoufinderrorsinthe
manual,pleasecontactusviathecontactinformationon
coverpage.
Withoutwrittenauthorization,itisnotallowedtocopy
andemulate
this
user
manual
wholly
orpartly.
Allrights
reserved.
-
8/13/2019 DSL-3011A User Manual
2/43
DSL3011AUserManual
V1.2
Usermanual
Thisusermanualiscomposedby8chapters.
Chapter Item Remarks
1Overview Introducetheinstrument
2
Unpacking and
inspectionIntroduceallthepartsinpackage
3Safety
Describe how to use DSL3011A
safely
4
General
operationand
usernotes
Introduce the operation and user
notes
5
Instrument
configuration
Introduce the configuration of
DSL3011A
6
Main functions
and
technicalparameters
Introduce the main functions and
technicalparameters
7Operation
Describe how to operate
DSL3011A
8
Malfunction
analysisand
solution
Introduce thegeneralmalfunction,
causesandsolutions
-
8/13/2019 DSL-3011A User Manual
3/43
DSL3011AUserManual
V1.2
Content
1 Overview ......................................................................................1
2 UnpackingandInspection............................................................1
3 Safety............................................................................................2
4 GeneralOperationandUserNotes..............................................3
4.1 OperationCriterion............................................................3
4.2 UserNotes .........................................................................4
5 InstrumentConfiguration.............................................................5
5.1 InstrumentFrontView ......................................................5
5.2 InstrumentUpsideView....................................................6
5.3 OtherParts.........................................................................6
6 MainFunctionandTechnicalParameters....................................7
6.1 xDSLTest ............................................................................7
6.2 LANTest .............................................................................8
6.3 CableTest...........................................................................8
6.4 DocumentManagement ...................................................9
6.5 SystemSetting ...................................................................9
6.6 Help....................................................................................9
6.7 Others ................................................................................9
7 Operation ...................................................................................10
7.1 Poweron/off....................................................................10
7.2 LCDDisplayIntroduction .................................................10
-
8/13/2019 DSL-3011A User Manual
4/43
DSL3011AUserManual
V1.2
7.3 xDSLTest ..........................................................................12
7.3.1 PhysicalLayerTest.................................................14
7.3.2 DSLParametersSettings .......................................17
7.3.3 ModemEmulation ................................................18
7.3.4 IPOptions..............................................................19
7.3.5 PPPDialup............................................................20
7.3.6
PingTest ................................................................21
7.4 LANTest ...........................................................................22
7.4.1 LANSettings ..........................................................22
7.4.2 PingTest ................................................................23
7.5 CableTest.........................................................................23
7.5.1 DMMTest ..............................................................24
7.5.2 ToneGenerator .....................................................28
7.6 RecordsManagement......................................................28
7.7 SaveRecordstoPC ..........................................................29
7.8
SystemSettings................................................................29
7.9 Help..................................................................................31
7.9.1 Instruction .............................................................31
7.9.2 About.....................................................................31
7.10 SoftwareUpgrade............................................................32
7.10.1 Softwareinstallation.............................................32
-
8/13/2019 DSL-3011A User Manual
5/43
DSL3011AUserManual
V1.2
7.10.2 Hardwareinstallationandupgradesteps.............32
7.11ChargetheBattery .............................................................36
7.12ReplacetheBattery............................................................37
8 MalfunctionAnalysisandSolution ............................................38
-
8/13/2019 DSL-3011A User Manual
6/43
DSL3011AUserManual
1
1 OverviewDSL3011Aisahandheldtesterwithcolordisplay,touchscreen
andlargecapacitybattery,whichcantestphysicallayerandnetwork
layer
quickly
and
accurately.
It
is
the
necessary
tool
for
xDSL
line
openingandmaintenance.
2 UnpackingandInspectionUponreceivingthepackage,conductavisualinspectionofthe
box to see if it has suffered any damage. If not, proceed with
unpackingandmakesuretheitemsinthepackinglistareincluded.
Contactourcompanyimmediatelyifanythingismissingordamaged
oryouwanttoaddorchangesomestandardaccessoriesoroptional
accessories.
MainParts:
Pleaseinspectwhetherthetypeandcodeontheinstrument
matchesthefollows.Type Code Specification
CN ChineseDSL3011A
EN English
Standardaccessories:
Thefollowingaccessoriesshouldbeincluded,pleaseinspectif
ithassufferedanydamage.Item Specs Quantity
Stylus/Touchpen 1
Alligatorclipcable 1.5meters 1
Cross over Ethernet
cable
2meters 1
Charger 8.4V/0.8A 1
-
8/13/2019 DSL-3011A User Manual
7/43
DSL3011AUserManual
2
Usermanual 1
Instrumentpackage 1
optionalaccessories:
Thefollowingoptionscanbepurchasedindependently.Item Spec Quantity
ToneGenerator TPT8010A Notlimited
3 SafetySafetyprecautionsshouldbeobeyedatalltimes.DADITelecom
shouldnot undertake any responsibility if clientsoperatewrongly
anddamagetheinstrument.
Please comply with safety precautions to avoid humans hurt or
instrumentdamage.
Warning
BatteryCharging
To charge battery, it is supposed to use matched charger
providedbymanufacturer,avoidusingunauthorizedcharger.Ifnot,
itmayleadtoinstrumentdamageoraccident.
ReplaceBattery
PleaseuseLithiumbatteryconfiguredbyFactory.Please
complywithclause7.11.
Donot
Operate
in
Explosive
Atmosphere
DonotusetheinstrumentinFlammable/ExplosiveLiquidand
atmosphere.Theoperationofanypowerrelatedinstrumentunder
thisenvironmentwillbedangerous.
DonotOpentheBackCover
Unlessreplacemodules,pleasedonotopenthebackcoveror
thebottomcover.Onlythetechnicianthathasbeentrainedcan
operateit,forsomepartsofinstrumentareofhighvoltage,any
improperoperationwillengenderdanger.
-
8/13/2019 DSL-3011A User Manual
8/43
DSL3011AUserManual
3
LCDDisplay
If LCDDisplay is damaged or liquid flows out, please do not
suckinortouch.Ifliquidisspatteredintoeyesormouth,pleasedo
washwithwaterandgotohospitalto inspect; Ifspatteredonskin
or clothes,pleasewashwithwateror soapafteralcoholwashing.Besides,notethatavoidskin(finger,hand,etc.)tobewoundedby
theglassfragments,avoidtouchingthefragmentsedge.
4 GeneralOperationandUserNotes4.1 OperationCriterion
TestInterface
Please connect test linewith the instrument interface, then
connectwiththetestedcircuit;Pleasedonottouchthebaremetal
partsofthetestniptopreventfromelectricshockifhighvoltagein
circuit.
USBInterface
PleasedonotjoinelectricequipmentintoUSBinterface,anddonotshortcircuitinterfacewithmetals,otherwisetheinner
circuitwillbedestroyed.
Display
Pleasetearoutprotectivefilmenclosedfordeliverybefore
usinginstrument.
Cleaning
The instrument cover, mainly made of plastics, should becleanedbysoftdrycloth, remembernot tousevolatilechemicals.
Otherwise,itmaybediscoloredorshapedistorted.
CoverandPanelProtection
Pleasedonotsprinklevolatilechemicalsoncoverorpanel,and
donotcontactchemicalswithRubberorPolyvinylChlorideinlong
timetopreventmalfunctionsoftheinstrument.
InstrumentMovement
When the instrument should be moved, please ensure that
-
8/13/2019 DSL-3011A User Manual
9/43
DSL3011AUserManual
4
power line and connection cable disconnected with instrument,
thentakeuptheinstrument.Pleaseunplugthecableafterusing.
BatteryMaintenance
Whentheinstrumentwillnotbeusedforalongtime,the
batterywilldeteriorateandbatteryshouldbechargedforalongtime.Ifittakesshorttimetochargeandsustainforashorttime,the
batteryshouldbereplaced.
Malfunction
Ifthereareabnormalsound,smellorsmog,pleaseshutdown
machineandunplugthepowerline,andremembertocontactDADI
TELECOM.
4.2 UserNotes
For the first time to use it, please fully charge instrument before
using, and make sure full charge before using each time. Please
refertoclause7.10tochargeinstrument.
PleasetouchmildlytheLCDdisplaywhenusingstylusandavoid
damage.
If there appears abnormal page or system frozen in the
operationprocess,pleasereboottheinstrument.
Pleasedonotput instrument in the sunornearheat source,
otherwiseitwillhavenegativeinfluenceoncircuitandcoverofthe
instrument.
Condensationmayoccur if the instrument ismoved tohigher
temperature place or temperature variable place. Under this
circumstance,itwouldbebetterfortheinstrumenttoadapttothe
temperatureformorethanonehourbeforeusing.
-
8/13/2019 DSL-3011A User Manual
10/43
DSL3011AUserManual
5
5 InstrumentConfiguration5.1 InstrumentFrontView
Indicatorlight
Fromlefttorightare:powerindicator,warningindicator,LAN
Linkindicator,ModempowerindicatorandxDSLLinkindicator.
Specificationsareasfollows:
Power Indicator: If red lighter is always on, it suggests the
instrumentisswitchedon.
WarningIndicator:whengreenlighterison,itsuggestsalarming
eventexistsintheline.
LAN Link Indicator: if green lighter is always on, it suggests
Ethernetlink
isnormal.
Ifgreen
lighter
blinks,
itmeans
Ethernet
hasdatastream.
Modem power indicator: if green lighter is on, it suggests
builtinModemmoduleisswitchedon.
xDSL Link Indicator: If green lighter blinks slowly, it suggests
findingofxDSLsignal. Ifgreen lighterblinksquickly, itsuggests
xDSL link protocol or training; If green light is always on, it
suggestsxDSLlinkhasestablished.
-
8/13/2019 DSL-3011A User Manual
11/43
DSL3011AUserManual
6
KeyButton
Mainlyincludeonoffkeyandsoftkeyboardkey.Specifications
foreachkeyareasfollows:
Onoff Key: Power on or off. Press the key to open the
instrumentwhentheinstrumentisclosed.Whenyouopentheinstrument,press it for1 second, shutdowndialogueboxwill
popup, theuserclicksandconfirm it toclosethe instrument.
Whentheinstrumentisabnormalandcannotbeclosedbyshut
downsystem iconoroffkey,pleasepressthekeyandholdon
for5seconds,thenthepowercanbeshutoff.
Softkeyboardkey:inoperationinterface,pressittoswitchsoft
keyboardorcloseit.LCDDisplayThescreenisTFTtruecolorLCDDisplaywithtouchscreenand
320240dotmatrix.
5.2 InstrumentUpsideViewPowerAdapterInterface
Thepoweradapterisdesignedfortheinstrument.Theinput
electricityis50HzAC220V,inputerrorrangeis10%,andoutput
voltageis8.4V.
xDSLInterface
xDSL interface is xDSL user line interface, it is also input
interfaceofDMMandoutputinterfaceoftonegenerator.
EthernetInterfaceRJ45
interface
that
comply
with
Ethernet
interface
standard,
is
used to connectwithEthernet cableorRJ45 cableplug forBroad
BandIP.Theinterfaceautomaticallyadaptstocrossoverordirected
cable.
USBInterfaceThe instrumentcanworkasanUdisk,afterconnectingtoPC,
thestoreddatarecordcanbedownloaded.
5.3 OtherPartsStylus
-
8/13/2019 DSL-3011A User Manual
12/43
DSL3011AUserManual
7
Stylus,astheaccessoryofthe instrument, isusedtoclickand
inputonthescreen.Itisusuallyplacedinupperrightcornerofthe
instrument,whenyouneedtouseit,youputitout,whenyoudont
need touse itandyouplug it into theoriginalposition toprevent
loss.TestLine
TheinstrumentisconnectedtotheleadofxDSLsubscriberline,
oneendoftheleadispluggedintosocketoftheinstrument,andthe
otherend isconnected into tested line.Whenyouoperate,please
donottouchthebaremetalofthealligatorcliptopreventelectric
shockcausedbyhighvoltage.
EthernetCable
Theequippedcableof instruments iscrossovercable,when it
connectswithbroadband IP cable, it canbedirectly connected to
Ethernetportof the instrument.When theEthernet connection is
normal,theEthernetindicatorontheinstrumentpanelison.
6 MainFunctionandTechnicalParameters6.1 xDSLTest
DSL3011A can emulate Modem + PC through builtin xDSL
Modem,completephysicallayerparameterstest,networklayertest
and application layer test of xDSL subscriber line, thus verify the
circuitquality.Thefunctionsareasfollows:
1.TechnicalParametersofPhysicalLayerTest
ADSL2+module:
Standards:ITU
G.994.1
G.hs
,ITU
G.992.5,
ITU
G.992.5
Annex
Lthemaxconnectingdistance:6.5km.ADSL,ADSL2,READSL
compatible.
1) TestDSLTransmissionParameter:
DSL upstream channel speed (interleaved/Fast): 0
1.2Mbps
DSLdownstreamchannelspeed (interleaved/Fast):024
Mbps DSLattenuation:063.5dB
-
8/13/2019 DSL-3011A User Manual
13/43
DSL3011AUserManual
8
DSLnoisemargin:032dB
DSLoutputpower:32.031.5dBm
DSL upstream/downstream maximum speed and channel
utilizationrate
Bits adjusted on DMT subchannel: 015subchannelsfrequencyquantity.
DSLcircuiterrorsquantity(CRC,HEC,FEC,NCD,OCD)
DisplaystatusonDSLcircuit:LOS,Linksfailure
DisplayDSLcircuitlinkmode
2.ModemEmulation
EmulateModemcompletely,usercandailupandlinkto
internet through the instrument, and verify whether there is
problemforuserModem.
3.PPPoEDialUpandModifyPPPoEDialupProperties
EmulatesubscriberModemandPC,PPPoEdialup,verifythe
connectivitybetweensubscriberandISPserviceprovider.
4.PingTest
SupportdomainnameandIPPingtest,includingPinglosstest
(customizedtime,packagesize),Pingloopbackdelaytest(max.min.
average).
6.2 LANTestCompletepingtestforLAN
6.3 CableTest1.DMMTest:
Testthe
DC/AC,
circuit
loop
resistance,
circuit
capacitance,
circuitinsulation.
TechnicalparametersofDMMtestareasfollows:
Item Unit TestRange Relativeerror
V 0110DC 5%2VVoltagetest
V 0110AC 5%2V
010 2Loopresistance
test
105000 5%
-
8/13/2019 DSL-3011A User Manual
14/43
DSL3011AUserManual
9
010 2nFCapacitance
testnF
10500 10%
01.0 0.1MInsulation
test
M
1.050 10%0.5M2.ToneGenerator
Builtinaudiosignalgeneratorsendsignalatoneendofthe
twistedpair,meanwhileuseanoptionaltonetracerinstrumentto
findthecorrespondingpairattheotherend.
6.4 DocumentManagementItcancompletebrowsing,viewinganddeletionoftested
record.
6.5 SystemSettingComplete timing set of backlit and autooff, factoryset and
displaycalibration.
6.6 HelpOnlinehelpandaboutareused.
6.7 Others Adopt320240TFTcolorLCD,withtouchscreen.
Adoptembeddedoperationsystem,Iconoperationinterface.
200recordscanbesavedanditcanhelpusersstoretestrecord
andexchangeitbyUdiscs.
Builtin rechargeable Li battery 7.4V 1500mAh, Max system
power3.5W.
Size:146mm87mm50mm Weight:0.6kg
-
8/13/2019 DSL-3011A User Manual
15/43
DSL3011AUserManual
10
7 Operation7.1 Poweron/off
1) Press the power key and the instrument begins towork, logodisplays on the screen, then operation interface displays asfollows:
2)NormalPoweroff: Click the Shutdown keyorpress thepower
key, awindowwill emerge to suggestwhether youwould like to
shutdown,thenconfirmit.
3)ForcedPoweroff:Whentheinstrumentcannotbeshutdownby
system icon or power key, please press power key, hold on 3
secondsand
the
instrument
will
beclosed.
7.2 LCDDisplayIntroductionWhenpoweron,instrumententersthemaininterface.Main
interfaceincludes3parts:statusindicatorbar,functionsiconbar,
toolbar.
1.StatusIndicatorBar
This bar includes LOGO, battery capacitance indicator and
timeindicator.
Functions Icon Bar
Tool Bar
Status Indicator Bar
-
8/13/2019 DSL-3011A User Manual
16/43
DSL3011AUserManual
11
TimeIndicator,Indicatethepresenttime,clickit,
thentimeanddatedisplay,youcanmodifytimeanddate
throughthiswindow,asisshowninthefollowingfigure:
You canmodify time and date by stylus, then press OK to
completeit.
Battery Capacitance Indicator: Indicate the present
capacitance status including 3 grids: full grids mean full
capacitance; 2 grids mean medium; 1 grid means littlecapacitancethatrequirecharging;emptygridisthestatus
of voltage lackbattery icon blinks and waiting for
charging. Charging status changes from one grid to two
gridsandthreegrids.
2.FunctionsIconBar
Thisbarincludesaseriesoffunctionsicons,eachrepresentsone
function,presstheiconandenterthefunctioninterface.
3.ToolBar
Thisbarincludes returnindicatorand SIPonoff
softkeyicon.
isreturnbuttonpressitandtheinterfacewillreturn
totheupperoperationinterface.
-
8/13/2019 DSL-3011A User Manual
17/43
DSL3011AUserManual
12
issoftkeyboardSIP,itcancontrolthedisplayor
hidingofthesoftkeyboard,usernotesareasfollows:
Ifthereisnoinputpanel,press andtheLCDwillsuggest
softinputpanel,thenafterthat,press toshutdownthesoft
inputpanelontheLCDDisplay.Softinputpanelincludesbasicletter
andnumberandalargepartofspecialsigns,asfollows:
SoftinputpanelandPCkeyboardhavesamefunctionsbasically,
enteranddisplayastheabovepicture.Inthestatus,youcaninput
lowercaseletter,number,andsomepunctuationsigns,youcanuse
touchpentoclickkeyofsoftinputpanelandcompleteinput.Shift
keyfunctionissameasinthePC.PressShiftkeyandthepanelwill
beasfollows:
Inthisstatus,itismainlyusedtoinputcapitalletterandsome
specialsignsandpunctuationsigns.
7.3 xDSLTestFunctionsIntroduction:
It connects and tests xDSL line and verifies dialup through
builtinModem.Asan integrated test, it includesADSL2+physical
-
8/13/2019 DSL-3011A User Manual
18/43
DSL3011AUserManual
13
layer tests,PPPdialup test, IPoE(DHCPandstatic IP)test,Modem
emulation and Ping test. The Tester can emulate user end
equipment toachievePPPoEdialupandperformanetwork layer
test. Itwillacquirethephysical layerparametersofthe linked line
and verify the line quality. This function is helpful to verify thesubscriber lineandsolveproblemsresultedfromausermodemor
PCproblem.
HowtoUse
ConnectoneendofthexDSLtestcabletotheRJ11portofthe
unitandtheotherendtothelinepairtobetested. Pressthe
icontoenterthexDSLtestwindow,asfollows:
xDSLtest
functions
includes:
physical
layer
test,
DSL
parameter
setup, Modem emulation, IP Options, PPP dialup, Ping test etc.
Clickthecorrespondingiconforeachtestorsetup.
IfyouonlywishtotestwhetherthebuiltinModemconnects
with xDSL station equipment,only theBasicTest isneeded.After
thexDSL indicator isON, (remainsgreen),just click theBasicTest
icontoopentheLineParameterwindowtocheckthephysicallayer
parameters.TotestwhetherthetestercanlogintotheISP,theprocedures
-
8/13/2019 DSL-3011A User Manual
19/43
DSL3011AUserManual
14
are: set Modem parametersVPI/VCIset PPPoE parameters
inputUserName/PasswordPPPoEdialupwhenxDSLLink
LEDison,doPPPoEdialup successfuldialupmeansasuccessful
logintotheISP.
7.3.1 PhysicalLayerTestFunctionIntroduction:Itisusedtotestphysicallayerparameters,including:xDSLlink
status, link mode, upstream rate, downstream rate, maximum
speed, channel utilization rate, noise margin, line attenuation,
outputpower,errorsCRC/HEC/FEC/OCD/NCD,activationtimes,test
timelength,channelbitdiagramandSNRdiagram.
Howtouse
TocheckphysicallayerparametersofxDSLline,pleaseclick
physicallayertesticontoenterthetestinterface,asfollows:
Parameterswillbedisplayedontheinterface,valuesbeingupdated
realtimetofeedbackthestatus.
ThroughxDSLpresentstatus,wecanseexDSLshakinghandsprocesswithstationequipment.Thelinkmodeispresentlinkmode.
-
8/13/2019 DSL-3011A User Manual
20/43
DSL3011AUserManual
15
PresentStatus:
Idle:notlinked
G.994Training:shakinghands
G.992Started:DSLAMdiscovercentralofficeDSLAM
G.992ChannelAnalysis:channelanalysisShowtime:linksucceeds
LinkMode:
ADI:ADImodeofADSL
G.DMT:G.DMTnegotiationmodeofADSL,correspondingwith
ITUTG992.1.
G.LITE: negotiation mode of ADSL, corresponding with ITUT
G992.2.
T1.413:T1.413negotiationmodeofADSL,correspondingwith
ANSIT1.413issue1&issue2.
G.DMT.BIS:G.DMT.BISnegotiationmodeofADSL2,
correspondingwithITUTG992.3.
G.DMT.BISPLUS:G.DMT.BISPLUSnegotiationmodeofADSL2+,
correspondingwithITUTG992.5.
PhysicalLayerParameters:
Frombeginningtopresenttime,totalModemactivationtimes.
Foreveryactivation,thetimewillincreaseby1.
After successful initiationofModem, the timeaccounts from
enteringphysicallayertest.
Click to enter channel bit distribution window.
Channelbitdiagram isdisplayed infigure,usercanclickto
movefigure,clickor+toenlargeorminimizefigure,asfollows:
-
8/13/2019 DSL-3011A User Manual
21/43
DSL3011AUserManual
16
Click to enter SNR distribution window, it is
displayedinfigure,clicktomovefigure,clickor+to
enlargeorminimizefigure,asfollows:
Click toentersaverecordwindow,asfollows:
-
8/13/2019 DSL-3011A User Manual
22/43
DSL3011AUserManual
17
Saverecordanddocumentnameisxxxxxxxxxxx.dsl,xisvalue,
youcanreviselinesigntolinecallNo.(easytorememberandkeep
record)
Click toenterthresholdsetupwindow,decideifthe
lineisqualifiedaccordingtopresentlineparameterandthreshold
setupvalue,asfollows:
7.3.2 DSLParametersSettingsFunctionIntroduction
Modify the relevant test parameters of xDSL, including the
VPI/VCIand
threshold.
HowtoUse
When you need to modify the relevant parameters of xDSL,
click on the DSL parameters setting icon, enter into DSL
parameterssettinginterfaceasfollows:
-
8/13/2019 DSL-3011A User Manual
23/43
DSL3011AUserManual
18
ModifyVPI/VCI
Upper part shows VPI/VCI settings, the instrument supports
fourpresetsofVPI/VCIparameters. (In this fourpresets, IPTV is
only bridge mode, can not use for PPP dial up by tester.) For
modifications,please inputVPI/VCIvalueagain,and thenclick the
Modify button below, after 2 seconds the system prompts
"configurationhasbeenchanged,effectiveafterreboot!Madesure
thatyouwant tosave theconfigurationand restart theModem?",
selectOKtocompletetheVPI/VCIvaluemodification.
Modifytheparametersthreshold
The lower part shows parameters threshold settings, the
instrument
will
display
the
previous
threshold
value.
For
modifications, please input the parameter threshold value again,
andthenclickOKbuttonbelow.
7.3.3 ModemEmulationFunctionsIntroduction
ItisusedintheemulationuserModem,whichcanreplacethe
users Modem and verifies whether there is problem for user
Modem.
-
8/13/2019 DSL-3011A User Manual
24/43
DSL3011AUserManual
19
HowtoUse
Click Modem emulation icon, then enter into the
Modememulationwindowasfollows:
Click the start Modem emulation button below, then the
instrumentisintheADSL2+Modememulationstate.
7.3.4 IPOptionsFunctionsIntroduction
Theseoptionsareusedtosetupprotocol,encapsulationand
detailedIPaddresses.YoucanselectPPPoEforPPPoEdailuptest
(RFC2516),IPoEforDHCPorStaticIPmodetest(RFC2684).
DHCPmode:UnchecktheStaticIPboxandclicktheRefresh
buttontogetIP.
StaticIPmode:ChecktheStaticIPboxandconfiguredetailed
ipaddresses.
HowToUse
Clickthe IPOptionsicon,toopentheIPOptionswindow
asfollows:
-
8/13/2019 DSL-3011A User Manual
25/43
DSL3011AUserManual
20
The system will save and reboot modem immediately after
clickingtheOkbutton.
7.3.5 PPPDialupFunctionsIntroduction
DoPPPdialupthroughbuiltinxDSLModemandestablishPPP
dialup.
HowtoUse
WhenxDSLLINKlighterison,click ,thenthesystemwill
popupPPPdialupwindow,asfollows:
ClickConnectbuttonandbeginPPPdailup,ifitsucceeds,itwillshowaconnectedmessage.
-
8/13/2019 DSL-3011A User Manual
26/43
DSL3011AUserManual
21
After thedialup isconnected, return to theprior interface to
check on the acquired IP address, default gateway and DNS
addressesbyclickingontheIPOptionsparametersicon.
The systemwillautomatically save thePasswordof the three
most recentusers. You can select oneof theseby clickingon theUsernameorthedropdownsymbol.
Confirm that theUsernameandPasswordarecorrect,or the
Dialupwillnotbesuccessful.
7.3.6 PingTestFunctionsIntroduction
To verify the IP connection with another TCP/IP PC through
sendingICMPfeedbackrequestinformation.Thereceivingstatusof
the feedback response information and the return times will be
displayed. Ping is themain TCP/IP command to test the network
connectivity,achievement,problemsofnameresolution.
HowtoUse
Click toenterintoPingtestwindow,asfollows
Targetaddressbar should input IP addressorwebsiteof the
Ping,The system will automatically store recently input five
-
8/13/2019 DSL-3011A User Manual
27/43
DSL3011AUserManual
22
addresses of target hosts (including IP and domain name) in the
convenienceof input forreuse,youcanselect throughclickingthe
dropdownsymbolnearthetargethost.
Tx time: sending times of data packages, default is 4 times.
Datalength:datalengthneedstobesent,defaultis56Aftersetting,clickPingbuttontostartthePingTest,theresult
ofPingTestissimilartoabovefigure.
PressClosetocancelthetest.
7.4 LANTestFunctionsIntroduction
ItisusedforLANconnectivitytest.
Howto
Use
Click LAN test icon; enter LAN test items, the LAN test
interfaceisasfollows:
7.4.1 LANSettingsFunctionsIntroduction
ModifyIPaddressandsubnetmaskofsystemcard.
Howto
Use
Click LAN settings icon, LAN setting window is as
-
8/13/2019 DSL-3011A User Manual
28/43
DSL3011AUserManual
23
follows:
Users can modify the IP address and subnet mask value
accordingtotheirownsituation,butthesettingvalueshouldbethe
legal value. Press the OK button to save the settings after the
modification.
7.4.2 PingTestFunctionsintroductionandusagearesameasDSLPingtest,see
section7.3.6
7.5 CableTestFunctionsIntroduction
Builtindigitalmultimeterwithfullautomaticrangeisusedfor
testingphysicalcharacteristicofthetelephoneline,tonegenerator(audiolinetrackingfunction)forfindingmatchedlinepair.
Howtouse
Click cabletesticon,enterintocableteststatus,the
interfaceisasfollows:
-
8/13/2019 DSL-3011A User Manual
29/43
DSL3011AUserManual
24
7.5.1 DMMTestFunctionsIntroduction
Builtin DMM can test AC/DC voltage, Loop resistance,
capacitance, insulation resistance etc. Maintainer can use these
testingfunctionstojudgeifthereis48Vvoltages,oranyshortand
opencircuitandcalculateroughlylinelengthatthesametime.
HowtoUse
Click DMMtest icon,enter intoDMMtestwindow,as
follows:
-
8/13/2019 DSL-3011A User Manual
30/43
DSL3011AUserManual
25
Thenconnecttestlinewithtestedline,clickthetestitemsto
startthetesting.Alltestintroductionsareasfollows:
DCVoltageTest
Usethevoltagetesttotestwhetherthereisasignalornot.For
xDSLlinethatbundledtoordinarytelephoneservice,ifthevoltageinthelineislowerorequaltoOV,itshowsthatlineserviceisnot
openorthereareseriousproblemssuchasbadinsulation,short
circuit,opencircuitetc.intheneedofcheckingandmaintenance.
ThistestisonlyforDCvoltagetest,thetestrangeis 110V+110V,
whenitexceedstestrange,instrumentwillpromptTestoverload.
ACVoltageTest
BytheuseofACtest,highACvoltagecanbetestedtoprotect
linemaintainerfromdanger,whenithashighACvoltage,takedown
thealligatorclipcarefullytoavoidelectricshock.
This test isonlyused forACvoltage test, thetestrange is0110V,
when it exceeds test range, the instrument will prompt Test
overload
LoopResistanceTest
ThelengthoflinecanbetestedbyLoopresistance.Vicevisa,if
the cable length is given, we can judge whether the cable
connectionisnormal.
L=RL/ROKm
TheformulaforcablelengthtestbyLoopresistancevalue
is
L=RL/RO
Km
Inaboveformula,RLisLoopresistancetestvalue(unit:),ROis
Loopresistanceperkilometer(unit:)
Generally,0.32mmcopperlineRO=435.2,0.4mmcopperline
RO=278.5,0.5mmcopperlineRO=178.3.
If the instrumentprompts TestOverload, itmeans that test
clip is not connected well or line isnt Loop connected or Loop
resistanceisoverload,pleasechecktestcliportestonceagainafterLoopconnectthelineend.
-
8/13/2019 DSL-3011A User Manual
31/43
DSL3011AUserManual
26
Duringthetest,when linehasvoltage (voltage isover5V), the
instrument will prompt Linevoltage, at this moment the Loop
resistancetestisunavailable,thetestcanbemadeonlywhenthere
isnoelectricityintheline.
ThelinelengthcanbeestimatedbytestingLoopresistance.ClickthelinelengthbuttonattherightsideofLoopresistancebutton,the
interfaceisasfollows:
If the current selection is default parameters, select
correspondingparameterinthecolumnoflinediameterparameters
selection,thenclickthecalculatebutton,youwillgetcorresponding
linelengthvalue.
Ifyouusecustomizedparameters, inputcorrespondingvalue in
customizedlinediameterparameter,thenclickthecalculatebutton,
youwillgetcorrespondinglengthvalue.
Capacity
Test
L=Cab/CO(Km)
The line length can be measured by capacitance test. When
thereisnobridgedtapandcableisnotdippedinwater,thelength
canbemeasuredbycapacitance,theformulais
L=Cab/CO(Km)
Inaboveformula,Cabiscapacitancetestvalue(unit:nF),COis
capacitancevalueperkilometer(unit:nF)In general, the common capacitance among cables for local
-
8/13/2019 DSL-3011A User Manual
32/43
DSL3011AUserManual
27
callsperkilometerisCO=51nF
When the instrument prompts Test Overload, that means
capacitance is overload or there is cable default, retest it after
checkingthecable.
Duringthetest,whenlinevoltageisover5V,instrumentwillpromptLinevoltage,andthenitwillreturntothelinetestmenu.
Atthismomentthecapacitytestisunavailable,thetestonlycanbe
madewhenthereisnoelectricityintheline.
The line lengthcanbeestimatedby testedcapacitancevalue.
Clickthe line lengthbuttonattherightsideofcapacitancebutton,
theinterfaceisasbelow:
The default line parameter is 51nF/Km; you can also set by
yourself.
Clickthecalculatebuttonwillgetthecorrespondinglinelength
value.
InsulationResistanceTest
Theinsulationtestfunctioncanbeusedforlineinsulationtest,
if
the
lines
insulation
resistance
value
is
small,
that
means
it
has
serious insulation problem, it may affect xDSL line transmission
quality, in general, the value of xDSL line insulation resistance is
supposedtobelargerthan10M.
During the test,when linevoltage isover5V, instrumentwill
prompt Linevoltage, at this moment the insulation test is
unavailable,thetestcanonlybemadewhenthere isnoelectricity
in the line. If the insulation resistance isoverload, the instrumentwilldisplayInsulationResistance :50M ,thatmeans the line
-
8/13/2019 DSL-3011A User Manual
33/43
DSL3011AUserManual
28
insulationisingoodcondition.
LineLength
Afterloopresistanceorcapacitancetest,thelinelengththat
calculated by current /Km or nF/Km settings will display on the
bottomofDMMtestinterface.7.5.2 ToneGeneratorFunctionsintroduction:
Builtinaudiosignalgeneratorwiththelingtracercanfindthe
correspondingphysicallineincentralofficeorapileofcables.
Howtouse
Click audiolinetrackingicon,enterintoaudioline
trackingwindowasfollows:
Click Stop button to stop audio signal sending, click Close
buttontoclosethewindow.
7.6 RecordsManagementFunctionsInstrument
Itismainly
applied
torecords
management.
HowtoUse
Click Recordsmanagementicon,enterintorecords
managementwindow,asfollows.
-
8/13/2019 DSL-3011A User Manual
34/43
DSL3011AUserManual
29
Select the requireddocument in thedocument list, thenclick
theViewbuttonandyouwilloverviewdetaileddocuments.Record
displayandrealtimetestarethesame.
7.7 SaveRecordstoPCThetestrecordsalsocanbecopiedtoPCviaUSBport.When
thetester isconnected toPCbyMiniUSBcable, itwillworkasan
USB disk with records in .dsl file format same as Records
Management.Youcancopytherecord filestoyourowndirectory
andopenthemwithourRecordViewersoftware.Youcanmanage
(view, rename andprint) all recordson this softwareor export as
a.csvformatfiletoopenwithMicrosoftEXCEL.
7.8System
Settings
FunctionInstrument
Provide timing set of backlight and automatic shutdown,
factorysetandscreencalibrationfunction.
HowtoUse
Click system setting icon, enter into function setting
windowasfollows:
-
8/13/2019 DSL-3011A User Manual
35/43
DSL3011AUserManual
30
AutomaticShutdown:equipmentsupportsautomaticshutdown
function.Iftheequipmentdoesnotoperateintheselectedtime,
the equipment will automatically shutdown the system to
expand the betray life. The optional time: 10 minutes, 20
minutes,30minutes,never(Automaticshutdownoff).
Backlit time: equipment supports automatic shutdown backlit
function. If the instrument does not operate in the selected
time,theequipmentwillautomaticallyshutdownthesystemto
expandthebetraylife.Theoptionaltime:5seconds,10seconds,
15seconds,30seconds,always(lightallthetime).
Alarm Beep onoff:Select the box of Enable, the beep is
allowedBlanktheboxofenable,thebeepisprohibited.
Factoryset: after click the button, itwill pop up a dialog box
Loaddefaultsettings?pressOKtheequipmentwillrestoreto
thefactory
set
automatically.
Screencalibration: it isused to calibrate the right response to
touchscreenclick.Afterclickthebutton,itwillpopupadialog
box Calibrate touch screen? press OK. There will be a
mark on the screen, click its central point; Repeat this action
when the subject moves until the screen return to normal
status.
Format Disk: it is used to format inner Flash Disk. Note: Thisoperationwillclearupallstoredtestrecords!
-
8/13/2019 DSL-3011A User Manual
36/43
DSL3011AUserManual
31
7.9 HelpFunctionsIntroduction
Providefunctionintroductionandusageoftheequipment.
Howtouse
Click HelpicontoenterintoHelpwindowasfollows.
7.9.1 InstructionFunctionsInstruction
The systems online help documents provide various usages
andbriefinstructionsoffunctions.
How
to
Use
Click icontoenterthesystemhelpwindow.
7.9.2 AboutFunctionsInstruction
Display the equipments software version and company
information.
Howto
Use
Click iconandenterintoAboutwindowasfollows:
-
8/13/2019 DSL-3011A User Manual
37/43
DSL3011AUserManual
32
Include the products software version and manufacture
information.
7.10 SoftwareUpgradeEquipmentcanupgradesoftwarethroughUSBport.Inorderto
avoid errors, please contact our company before you upgrade
(contactthebackcover),confirmtherequiredupgradesoftwareand
completetheupgradeunderourcompany'stechniquesupport.
7.10.1 SoftwareinstallationRunDfuSe_Demo_V3.0_Setup.exefile:theInstallShieldWizard
willguideyoutoinstall.DfuSeapplicationsandsourcecodeonyour
computer.Whenthesoftwareissuccessfullyinstalled,clickthe
Finishbutton.
You
can
then
explore
the
driver
directory.
The
driverfilesarelocatedintheDriverfolderinyourinstallpath
(C:\Programfiles\STMicroelectronics\DfuSe).
7.10.2 Hardwareinstallationandupgradesteps1. ConnecttheinstrumenttoaspareUSBportonyourPC.
2. Pressthepowerkeyandonoffsoftkeyboardatthesame
timewhentheinstrumentisoff,atthistimethescreenis
white,whichmeansitiswaitingforcheckingofsoftwareupgrading.
-
8/13/2019 DSL-3011A User Manual
38/43
DSL3011AUserManual
33
(Youcanskipstep3to8ifyoudidthesoftwareupgrade
successful)
3. TheFoundNewHardwareWizardthenstarts.Selectthe
No,notthistimeasshownbelowandthenclickNext.
4. SelectInstallthesoftwareautomaticallyasshownbelowand
thenclickNext.
-
8/13/2019 DSL-3011A User Manual
39/43
DSL3011AUserManual
34
5. ClickcontinueAnywaytocontinue.
6. IntheCopyfilesfrom:dialogbox,clickBrowse...tospecify
thedriverfileslocation,thedriverdirectoryislocatedinyour
-
8/13/2019 DSL-3011A User Manual
40/43
DSL3011AUserManual
35
installpath(C:\Programfiles\STMicroelectronics\DfuSe\Driver
\x86),thenclickOK.
7. Windowsshouldthendisplayamessageindicatingthatthe
installationwassuccessful.ClickFinishtocompletethe
installation.
-
8/13/2019 DSL-3011A User Manual
41/43
DSL3011AUserManual
36
8. Open theDfuseDemo softwareonPC, at thismoment itwill
check the instrumentautomatically (under theActionscolumn
there will be a similar display 00 Internal Flash 256
sectors..)asfollows:
9. Click button,selecttheupgradedocument.
10. Click buttontostartupgrade,atthismomentthe
bottom scrollbarwilldisplay theprogress.Aftercomplete the
upgrade,click toexitthesoftware.
7.11ChargetheBattery
There is builtin 7.4V 1500mAh Li battery in this instrument.
Whenbatterysignisempty,the instrumentwillpromptnobatteryandshutdown1minute laterautomatically. Inordertonotaffect
-
8/13/2019 DSL-3011A User Manual
42/43
DSL3011AUserManual
37
yourusage,pleasechargeitimmediately.
Libatterycanbechargedanytimebecause ithasnomemory
effect.Weadviseyoutochargethebatteryimmediatelywhenithas
onegridsoastoaffectnormaluse.
Howtocharge:firstly,shutdownthe instrumentandconnectAC220V inputplugwithAC220Vsocket,thenputtheoutputplug
of charger into the charge port of the instrument. When the
instrumentisclosed,thechargetimeshouldbelessthan12hours,
orelseitwoulddamagetheinstrument.
Whentheinstrumentischarging,theindicatorisredwhenit
turnsgreenthatmeansthebatteryisfull.
7.12Replace
the
Battery
Becausethebatteryisspeciallydesignedfortheinstrumentby
the factory, you cannotbuy it in themarket,please contactDADI
whenyouneedtochangeit.
How to replace: place the instrument face down, turn the
central fixed screw which under the battery box with the
screwdriver, open the battery cover, pull the battery out of the
socket.Replace theoriginalbatterywith anewoneofDADI, and
tightenthescrew.
Don'tdisposethebattery,putitintobatteryrecycleboxorgive
ittoprofessionaldepartment.
-
8/13/2019 DSL-3011A User Manual
43/43
DSL3011AUserManual
8 MalfunctionAnalysisandSolutionProblems ReasonAnalysis Solutions
Instrumentcan
notopen Lowbattery
Turn on after full
charge
Wheninstrument
isinxDSLtest
status,the
builtinModem
activationinthe
xDSLlineis
disabledinlong
time.
1.Thelineis
disconnected.
2.Nolinesignal,
testifthelinehas
48Vvoltageby
DMMvoltagetest
1.Confirmifthelineis
Connected then start
thetest.
2.Ifthereisno
voltage,itshows
serviceisnotopened
inthisline
Afterashorttime
ofxDSLtest,the
instrument
promptslow
batteryandshuts
down.
Becausethe
builtinModem
haslargepower
consumption,the
powercannot
supplyenough
powerforxDSL
test
Chargethebattery
beforexDSLtest.
PPPoEdialcan
notworkbut
activationhasno
problem
Pleaseconfirmif
usernameand
passwordarecorrect,VPI/VCI
andPPPoE
propertiessetup
arecorrect.
ModifythePPPoE
propertiesaccording
toaccessrequirementofthe
line,andinputthe
correctpasswordfor
PPPoEdialup.