drying_tumbler_t81e.pdf - wesco-navy€¦ · ©wesco 2008 4 anchoring of tumble dryer the tumble...

Drying tumbler/Wäschetrockner T 81 E

Manual/Spare part listBedienungsanleitung/Ersatzteilliste

CAPACITY 6-9 KG DRY LAUNDRY

Fill the drum with laundry1.

Close the door properly2.

Choose temperature and program setting3.

Push the program knob to start4.

Let always the program finish. Clean the lint filter after usage

Automatic stop

Stops when the laundry is dry

1 Delicate 40/60°C

2 Perm/Press 40/60°C

Manual time set

Stops after the set time

3 Select the temperature and set

time manually

10 20 30 40

50

60 7

0

PROGRAM CHOICE

TEMPERATURE

SETTING

Heat Cooldown

3Manual

timeset

0º/40º/60º

1Delicate

40º/60º

2Pern/Press 40º/60º

0º

40º

60º

INSTRUCTIONSTUMBLE DRYER T 165 E

Tumbler Dryer T61E & T81E

3 ©WESCO 2008

ContentsInstallation 3 Anchoring of tumble 3 Anchoring of plinth 3 Ventilation 4 Electrical connection 4 Connection of the condenser unit C2 4 Connection of the channel fen 4 Maintenance 4 Condenser Unit C2 4 Important 4 Condenser unit C2 5 Installation 5

Warmth exchanger 5 Installation 5

Changing right door to left door 6

Spare parts 7

Wiring diagram 15

Schematic 16 Schematic 200V~3N 17 Schematic 400V~3N 18 Schematic 440V~3N 19

Exhaust system 18

Measurements 19

4©WESCO 2008

Anchoring of tumble dryer The tumble dryer has four (4) adjustable feet and can be placed directly on the floor without any extra anchoring. Adjust the feet, so that the dryer is horizontal. Check width and depth

Anchoring of plinth, 200 mmUse M8 expander- or anchor bolts when anchoring the plinth.Minimum size: side 20 mm, back 400 mm.

Ventilation The hose connection of the dryer has a Ø 100 mm. The ventilation channel must be dimensioned for an air quantity of 300 mm3/h. If several dryers are attached to the same channel, it should be dimensioned so that the air resistance is the same for all connected dryers. The ventilation channel should be separated from other ventilation systems. Connect the dryer to the venti-lation channel with a flexible hose.

Electrical connectionThe electrical connection must be stationary and must be pre-pared with an approved allpole head switch, preferable sup-plied with a signal lamp.

A three-pole 1,5 m2 connecting cable with protective earth conductor must be used. Main fuse 10 A, voltage 380 V, 3N.

Disconnect the protective sheet plate on the back of the connection box. Connect phases, null and earth.

Connection of the condenser unit C2Use a one-phase 220 V, 50 Hz with a cable glander between the condenser unit and the dryer. Connect the cable through the cable glander to the connection box on the back of the dryer and in to the connection box on the condenser unit.

Assemble the ventilation hoses between the in- and outcoming air channels on the dryer and condenser unit. Tighten the hoses, so that they are not hanging under the dryer’s incoming and outcoming air connections.

Connecting the channel fanConnect 220 V, 50 Hz on the back of the dryer to the connection box. The channel fan is regulated through the dryer’s timer.

MaintenanceThe lint filter, must be cleaned every time the dryer has been used. Continuos maintenance of the dryer shall be done at least once every 6 month. Continuos maintenance includes control of the dryer’s different functions and cleaning inside.

Condenser UnitThe warmth exchanger shall be cleaned when necessary. Appropriate interval is once a month. Loosen the frame around the condenser unit and take out the filter and clean it. Then carefully take out the dehydrating unit and clean it under run-ning water. Don’t forget to clean the condenser box around the drain before you put everything back.

ImportantAll energy from the condenser unit which are used when drying, gives the surrounding areas a surplus of warmth. It is therefor important to have a sufficient ventilation system which handle the extra warmth.

Fasten the plinth in the floor (the blind nuts shall be placed 1. forward and upwards).

Place the dryer on the plinth. Adjust the feet on the bottom 2. of the dryer to the plinth, so the dryer is horizontal. Try to keep the feet as low as possible, gives it more stability.

Loose the lower front plate.3.

Anchor the two M6-bolts that are attached, through the 4. bottom plate in the front of the plinth. (Pic. 1)

Anchor the thin sheet metal at the back, between the plinth 5. and the dryer with attached screw for sheet metal. (Pic. 2)

.

Installation

Pic. 1

Pic. 2

5 ©WESCO 2008

Condenser unit C2

20 mm 400 mm

Rek1400 mm

Installation C2The condenser unit is delivered ready for use and shall be assembled on the wall behind or on the side of the dryer. Ventilation hoses are assembled and condenser water pipes is drawn to the floor drain. A separate manual is enclosed about how to connect incoming air. The condenser unit is connected electrical via the dryer and is regulated through its start- and stop functions.

The surplus warmth is staying in the drying room. We therefor strongly recommend a sufficient ventilation.

20 mm 400 mm

Rek1400 mm

Warmth exchanger

Installation warmth exchangerThe warmth exchanger is delivered ready for use and shall be assembled on the wall, behind or on the side of the dryer. The ventilation hoses are assembled and condenser water pipes drawn to the floor drain. A separate manual is enclosed about how to connect incoming air.

If you need an extra channel fan, this can be connected to the connection box 220 V, 50 Hz, regulated via the dryer’s timer.

6©WESCO 2008

Instruction for changing right door to left door

There are 2 hinges (position 5) on the right side of the 1. door with 2 screws (position 6) each. Please unscrew all 4 screws.

Turn the door upside down.2.

Inside the door is a filter cassette that also has to be turned 3. upside down.

On the opposite side of the dooor are 4 holes to install the 4. 2 hinges and the 4 screws again.

This action will take about 10 minutes.

7 ©WESCO 2008

Spare parts

Nr Art Nr Description

1 W 56064 Top plate

2 W510212 Fabric selector switch

3 W502964 Timer

4 W56070 Top frame

5 W121025 Transformer 700 VA

6 W510287W Switch knob

7 W7520 Emergency button

1

4

3

2

6

7

8 9

5

8©WESCO 2008


1 W510127 Door Striker Bracket

2 W510181 Door Striker

3 W510147 Door Seal

4 W510163 Inner Door Panel and Seal Assembly

5 W505295 Screw

6 W510179 Door Hinge

7 W510066 Front Panel

8 W510103 Door Pull

9 W510013 Outer Door Panel

10 W510129 Wedge

9 ©WESCO 2008


1 W28835 Hold-down Clip

2 W504570 Door Switch

3 W510236 Front Panel Seal

4 W510066 Front Panel

5 W510795 Label

6 W503688 Screw

7 W33562 Slotted Hex Head Screw

8 W510069 Access Panel

9 W56079 Locator

10 W32671 Screw

11 W502804 Label

12 W510177 Door Catch

13 W500281 Label

10©WESCO 2008

Nr Art Nr Description Nr Art Nr Description

1 W510238 Seal 14 W56156 Lock Nut

2 W31260 Screw 15 W510133 Idler Lever

3 W510140 Exhaust Fan Cover 16 W56461 Shaft

4 W510139 Exhaust Fan Impeller 17 W52549 Washer

5 W510138 Exhaust Fan Housing 18 W510142 Idler Pulley

6 W501212 Motor Assembly 19 W23748 Retainer Ring

7 W501218P Motor Switch 20 W500824 Shoulder Bolt

8 W510180 Motor Mounting Clamp 21 W510158 Idler Pulley and lever Assembly

9 W510178 Belt 22 W52566 Lock Nut

10 W500222 Motor Pulley 23 W510060 Motor Mounting Bracket

11 W590P3 Motor Hub Ring Kit 24 W510084 Base

12 W503688 Screw 25 W33561 Screw

13 W510185 Spring 26 W504518 Thermostat

11 ©WESCO 2008

Nr Art Nr Description Nr Art Nr Description

1 W510238 Seal 14 W56156 Lock Nut

2 W31260 Screw 15 W510133 Idler Lever

3 W510140 Exhaust Fan Cover 16 W56461 Shaft

4 W510139 Exhaust Fan Impeller 17 W52549 Washer

5 W510138 Exhaust Fan Housing 18 W510142 Idler Pulley

6 W501212 Motor Assembly 19 W23748 Retainer Ring

7 W501218P Motor Switch 20 W500824 Shoulder Bolt

8 W510180 Motor Mounting Clamp 21 W510158 Idler Pulley and lever Assembly

9 W510178 Belt 22 W52566 Lock Nut

10 W500222 Motor Pulley 23 W510060 Motor Mounting Bracket

11 W590P3 Motor Hub Ring Kit 24 W510084 Base

12 W503688 Screw 25 W33561 Screw

13 W510185 Spring 26 W504518 Thermostat


1 W510159 Front Bulkhead

2 W510207 Cylinder Seal

3 W510102 Baffle

4 W510265 Cylinder Assembly

5 W62588 Screw

6 W510002 Cabinet Panel

7 W510187 Cylinder Glide

8 W510145 Glide Bracket

9 W52864 Screw

10 W503688 Screw

11 W501086 Screw

12 W510151 Air Duct Assembly

13 W503980 Lint Filter

14 W510189 Felt Pad

15 W501285 Screw

12©WESCO 2008


1 W510207 Cylinder Seal

2 W503688 Screw

3 W505244 Rear Bulkhead

4 W501285 Screw

5 W510237 Shield

6 W510190P Terminal Block

7 W61199 Screw

8 W510025P Heater Assembly

9 W510002 Cabinet

10 W510100 Roller Bracket

11 W510708P Cylinder Roller

12 W56156 Lock Nut

13 W56461 Shaft

14 W504082 Wave Washer

15 W52549 Washer

16 W23748 Retainer Ring

13 ©WESCO 2008


1 W503688 Screw

2 W500820 Outlet Cover

3 W510025P Heater Duct Assembly

4 W510183 Thermal Fuse

5 W23222 Screw

6 W510701 Limit Thermostat

7 W10056 Heater Assembly, 3x1600W 380V

14©WESCO 2008


1 W56079 Locator

2 W32671 Screw

3 W56128 Bumper


5 W510136 Top Hinge

6 W503688 Screw

7 W500670 Label

8 W503456 Bracket

9 W510903 Access Cover Plate

10 W501289 Label

11 W510137 Exhaust Duct


13 W510135 Leveling Leg

14 W501855 Rubber Foot

15 W510084 Base


WESCO Navy GmbH, Zitterpappelweg 9, D-22391 HAMBURGTel. +49 40 536 00 61, Fax +49 40 536 75 01, e-mail [email protected]

©WESCO 2008-12-09

drying_tumbler_t81e.pdf - wesco-navy€¦ · ©wesco 2008 4 anchoring of tumble dryer the tumble...

Documents