Download - ROLL-FORMED SECTION The process
![Page 1: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/1.jpg)
1
ROLL-FORMED SECTION The process
•Roll forming is process in which strip or coiled sheet metal is fed continuously through a series of contoured rolls arranged in tandem.•Only bending takes place , the metal gauge essentially remains constant.• the number of pairs of rolls required to form a particular part depends on :-
![Page 2: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/2.jpg)
2
• Material• Shape to be formed• The precision required
Other operations like notching ,piercing, embossing, welding can be incorporated into the operation.
![Page 3: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/3.jpg)
3
• The most common operation is a “ flying” cutoff operation after operation is completed.
• Punch –press operation are normally located ahead of rolling
![Page 4: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/4.jpg)
4
APPLICATIONS
•Roll forming is a continuous bending operation in which a long strip of metal (typically coiled steel) is passed through consecutive sets of rolls.•Roll forming is ideal for producing parts with long lengths or in large quantities.•A variety of cross-section profiles can be produced, but each profile requires a carefully crafted set of roll tools.•Roll forming can be carried out with plated , galvanised ,lithograped ,vinyl-coated etc…
![Page 5: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/5.jpg)
5
• Dual layered components can also be made at one time.These may include bimetallic parts such as those made when a thin stainless-steel facing sheet and a carbon steel support sheet are formed together.
• Long pieces like railroad-car and truck-trailer trim members can be made with this process.Maximum length of part is dictated only by application requirements and handling conditions.
![Page 6: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/6.jpg)
6
CROSS SECTIONS
![Page 7: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/7.jpg)
7
Typical parts and applications
![Page 8: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/8.jpg)
8
Applications• Roll forming is best applicable for constant complex cross-sectional
shapes.
• Parts often are long length (short part made by cutting strips).
• Possible thickness rolled is 0.13- 25 mm.
commercial limit is 0.25- 4 mm.
width range is 25 mm- 2.5 m.
commercial maximum width is 1 m.
but 400 mm widest stock processible on commonly available machines.
![Page 9: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/9.jpg)
9
applications• Deep forms are difficult (100 mm is practical depth limit).
• Roll formed components are applicable for mass production.
• Building industry – roof and sliding panels, joists, windows frames, downspouts, architectural trim and copper electrical conductors.
• Hot rolling- sheet metals , rail tracks.
• Ring rolling – turbine , pipes, pressure vessels.
![Page 10: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/10.jpg)
10
applications• Appliance parts made by roll forming includes:- panels for
stoves, refrigerators, lighting fixture parts.
• Curtain rods and tracks for sliding doors, drawer handles and metal picture frame members made by rolling.
• Curling (longitudinal bending) can be rolled eg. Bicycle fenders and wheels, barrel hoops, drum rings etc.
![Page 11: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/11.jpg)
11
Assumptions Of Rolling Process
![Page 12: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/12.jpg)
12
• The rolls are straight and rigid cylinders.• The width of the strip is much larger than its
thickness and no significant widening takes place.
• The co-efficient of friction µ is low and constant over the entire roll-job interface.
• The yield stress of the material remains constant for the entire operation , its value being the average of the values at the start and at the end of rolling.
![Page 13: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/13.jpg)
13
• On this assumption,we calculate the following parameter-
a. Torque and power required to drive the rollsb. Roll separating forcec. Power loss in bearing
![Page 14: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/14.jpg)
14
Economic Production Quantities• Roll Forming-Mass Production process
• Production rates are rapid
• Setup and tooling costs high
• For process to be economic at least 100,000ft/yr must be produced
• In some cases 500,000ft/yr is required to make the process justifiable-depending on configuration and efficiency of alternative methods
![Page 15: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/15.jpg)
15
• Set up times are lengthy due to the large number of tooling elements that are interrelated
• Once operative it is an extremely fast process
• Speeds upto 300 ft/min, though average speeds of 50 to 100 ft/min
• Low labour cost
![Page 16: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/16.jpg)
16
• As compared with extrusion or machined parts there is a savings in materials cost
• Overall this contributes to very low cost of production which more than makes up for the high initial setup and tooling costs
![Page 17: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/17.jpg)
17
Material Properties
• All normally formable materials may be used.• Best results with ductile alloys but extreme
ductility is not required.• Deformation parallel to grain lines of the
material prevents fracture.
![Page 18: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/18.jpg)
18
Suitability for Cold Rolling
• Determined by tensile properties• Tensile properties depend on crystal structure• Cold rolling changes crystal structure and
thereby the tensile properties• Material selection should consider change in
properties due to cold working.
![Page 19: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/19.jpg)
19
Elastic Propertiesσ
ε
σ
ε
Suitability for rolling depends on two properties:
a) Magnitude of yield point stress
b) Extent of plastic region
![Page 20: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/20.jpg)
20
Springback• Strain in the plastic region is
partly elastic and partly plastic• On removal of deforming
force, elastic strain is recovered
• Plastic strain is retained
σ
ε
This recovered elastic strain is called springback.
Applied strain should exceed required strain by this value.
![Page 21: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/21.jpg)
21
Materials Used• Steels – low carbon, stainless, high alloy
steels• Aluminium, Brass, Bronze, Copper• Clad, plated, anodized, galvanized,
organically finished materials• Pre painted stock if coated with durable,
non brittle, baked finish.
![Page 22: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/22.jpg)
22
Design Recommendations
• Parts designer must understand the process thoroughly
• Must be in contact with the engineer who understands the roll forming operation, equipment and tooling i.e. sequence of operations
• High tooling costs, tool wear and forming problems can be reduced by reviewing the sequence of operations.
![Page 23: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/23.jpg)
23
Bending Radii
• Bending radii at both inside and outside corners must be generous- atleast equal to stock thickness or preferably twice stock thickness
• Radii less than one stock thickness possible- sharp bends-
• requires sharp corners on the forming rolls• Reduces roll life significantly
![Page 24: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/24.jpg)
24
Approaches for sharp bends
• For stock upto 0.8mm in thickness external bead can be used
• For stock greater than 0.8mm a formed groove one third to one half of stock thickness facilitates bending.
![Page 25: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/25.jpg)
25
Part Length
• Form the stock in long lengths and cut to length after forming-one continuous automatic operation
• Sometimes there are minimum length limitations for roll formed pieces
• There are entrance and exit flare distortions at each end
• Parts shorter than 3 times the centre line spacing of rolls of the machine employed will not form satisfactorily.
![Page 26: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/26.jpg)
26
Depth of Form
• Deep profiles require correspondingly larger diameter forming rolls -more costly
• Differential amount of pull exerted on the stock due to the different peripheral speeds
• Slippage and roll wear occur• Maximum form depth generally 100mm
![Page 27: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/27.jpg)
27
• Some forming machines equipped with differential gearing
• So that large diameter rolls can be run at lower rpm-to match peripheral speed to stock speed
• Such machines can form deeper sections
![Page 28: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/28.jpg)
28
• Perfectly symmetric types are good for roll forming
• Even if perfect symmetry is absent, it can still be used by having equal bending on either side of centerline
• Non symmetrical forms require straightening as a part of forming
Symmetrical/Balanced Forms
![Page 29: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/29.jpg)
29
• Exactly vertical sidewalls should be avoided to reduce troubles for roll former
• Excessive roll wear and scoring of the work piece is thereby reduced
• This is done by including a draft angle of ½ degree
Vertical Sidewalls
![Page 30: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/30.jpg)
30
Possible
Preferred
![Page 31: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/31.jpg)
31
• Some feasible blind corners and radii are shown here
• When precise bends are needed, these should be avoided
• Controlling both sides of stock by rolls, facilitates accurate forming
Blind Corners
![Page 32: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/32.jpg)
32
Feasible
Preferable
![Page 33: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/33.jpg)
33
• Minimum possible practical length for formed legs is 3 times stock thickness
Minimum Length
Not this This
![Page 34: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/34.jpg)
34
• Factors causing dimensional variations – spring back, variations in hardness, thickness, and yield point of material, tooling deviations and tooling wear, setup and adjustment of tooling and machine deflection
• Close tolerances are held with thinner stock and smaller parts
• Tighter ones are held at extra cost
Dimensional factors & Tolerances
![Page 35: ROLL-FORMED SECTION The process](https://reader036.vdocuments.mx/reader036/viewer/2022062517/568138f5550346895da0aa1e/html5/thumbnails/35.jpg)
35
DIMENSION TOLERANCES
Section/leg width/height <= 50 mm
+ or – 0.25 mm
Section/leg width/height > 50 mm
+ or – 0.4-0.8 mm
Angle + or – 1 degree
Twist 3.5 mm
Camber 0.8 mm/m
Tolerances for roll formed parts