Download - Ies5000 config guide
•www.adcom.co.th
IES‐5000 SystemIES‐5000 System
Configuration guideConfiguration guide
•Advanced Comm Co., Ltd.
A dA d•www.adcom.co.th
AgendaAgenda
•Products overview
•Get StartGet Start
•ADSL configuration guide
H 248 fi i id•H.248 configuration guide
•SIP configuration guide
•Configuration File & Firmware
•DiagnosticDiagnostic
•Advanced Comm Co., Ltd.
Products overviewProducts overview•www.adcom.co.th
Products overviewProducts overview
•IES‐5000 overview
MSC1000G i•MSC1000G overview
•ALC1248G‐51 overview
•VOP1248G‐61 overview
•Splitter wiringp g
•Advanced Comm Co., Ltd.
IES‐5000 overviewIES‐5000 overview•www.adcom.co.th
•48-port ADSL2/ ADSL2+ Annex BManagement card
•48-port ADSL2/ ADSL2+ Annex A
•48-port SHDSL/SHDSL.bis
48 port ADSL2/ ADSL2+ Annex A
•72-port ADSL2/ ADSL2+ Annex A
•24-port VDSL2 line cardpo t S e ca d
•48-port VoIP POTS line card
MSC1000G overviewMSC1000G overview•www.adcom.co.th
ACO
Alarm
ACO
Console portport
SFP Open Slot1000 Base T Eth t
Out‐of‐band Management
SFP Open Slot Ethernet
ALC1248G‐51 overviewALC1248G‐51 overview•www.adcom.co.th
Telco 50 connecterPowerLED
ALC1248G 51
Telco 50 connecter
ALC1248G‐51
SystemLED
AlarmLED
Console port
•Maximum transmission rate up to 25 Mbps/p p
•1.2 Mbps for ADSL2+, support Annex M,L
VOP1248G‐61 overviewVOP1248G‐61 overview•www.adcom.co.th
Power LED
System LED
Telco 50 connector Alarm LED Test in/out port
Console port
-support H.248 version 2 or SIP singling protocol
upon firmware using (default is SIP)
Splitter wiring•www.adcom.co.th
•MSC‐1024•P1 •P2
•IES‐5005
•ALC‐1248
•PBX•Splitter
•VOP‐1248
•1•Disconnection
•10
•Back Mount Frame
•DSL CPE
•Splitter•Splitter
DSL CPE•DSL CPE
G t St tG t St t•www.adcom.co.th
Get StartGet Start
•Login
•IP setupIP setup
•Advanced Comm Co., Ltd.
Login #1
•Web browser•www.adcom.co.th
IP Address : 192.168.1.1
Username : adminPassword : 1234
* Outband IP Address : 192.168.0.1
Login #2•www.adcom.co.th
Console CLI
9600 bps, No parity, 8 data bits, 1 stop
bit,No flow control
Username : adminPassword : 1234
IP Setup•www.adcom.co.thSys -> IP Setup
Click
Change IP and gateway to Management NetworkManagement Network
ADSL configuration guideADSL configuration guide•www.adcom.co.th
ADSL configuration guideADSL configuration guide
Step1: ADSL/default VLAN setup
Step2: Profile setup
Step3: Port setup
Step4: PVC setup
Step5: VerifyingStep5: Verifying
•Advanced Comm Co., Ltd.
Step1: VLAN setup #1Step1: VLAN setup #1•www.adcom.co.thVLAN -> VLAN (Create Service VLAN)
ClickAdd VLAN 79-Name : Internet-Port up2 : Fixed and Ch TChoose Tag
-Port sub1, sub2, up1 : Forbidden
Step1: VLAN Setup #2•www.adcom.co.thVLAN -> VLAN (Create Management VLAN)
ClickAdd VLAN 49-Name : MGMT-Port up2 : Fixed and Choose TagP t b1 b2 1 F bidd-Port sub1, sub2, up1 : Forbidden
Step1: VLAN Setup #3•www.adcom.co.thSys -> IP Setup (Change Management VLAN)
Change Management VLAN
Click
* Please configuration via outband (MGMT) port IP Address 192.168.0.1
Step2: Profile Setup•www.adcom.co.thProfile -> ADSL
Add profile name and speed rate
Step3: Port Setup#1•www.adcom.co.thPort -> ADSL
1 Select slot click “Load”, then select Port, click “Load”.2 Choose Enable3 Select Mode4 Select ADSL ProfileSe ec S o e5 Advanced feature click “Setup”
(See next slide)6 Click “Apply”Click 6 Click ApplyClick
Click
Step3: Port Setup#2•www.adcom.co.thPort -> ADSL (Advanced feature setup)
Step3: Port Setup#3•www.adcom.co.thPort -> ADSL -> Copy
Select port then click or click All for selectSelect port then click or click All for selectAll port then Click Apply to Delete
1 Click
3 Click2 Click
Step4: PVC Setup•www.adcom.co.thPort -> PVC
1 Select slot then click1 Select slot then click “Load”2 Select port then click “Load
Click 3 Add VPI/VCI4 Add PVID (VLAN ID)5 Select Profile6 Click “Apply”6 Click Apply
Click
Step5: Verifying•www.adcom.co.th
Statistics -> Port Statistics
H 248 configuration guideH 248 configuration guide•www.adcom.co.th
H.248 configuration guideH.248 configuration guideH.248 introduction
H.248 example
Step1: Voice VLAN setup
Step2: setup card IP
Step3: setup signal/media card
Step4: setup H.248 gateway
Step5: setup profile
Step6: setup H.248 interface
Step7: setup port terminations
Step8: port isolation
Step9: Verifying•Advanced Comm Co., Ltd.
H.248 Introduction•www.adcom.co.th
•MGC
IP•MG •MG
•
•IP NETWORK
•ANALOG
•User C •User D
•ANALOG•ANALOG
•H.248 VoIP network has a single intelligent control unit, which manages a network of dumb endpoint devices.
H.248 example•www.adcom.co.th
•GW
•Softswitch
•192.168.17.18
•10.134.32.254
•Signal card
•10.134.32.37/24
•H.248 interface
•10.134.32.36/24 0 3 3 3 /
•media card
•10.134.32.39/24
Step1: Voice VLAN setup•www.adcom.co.th•VLAN->VLAN
1 S tti V i VLAN1. Setting Voice VLAN up
Step2: setup card IP#1•www.adcom.co.th•VoIP->IP 1.For example: the H.248 interface address is
ip: 10.134.32.36/24 gw: 10 134 32 254gw: 10.134.32.254
2. Setting card IP address with same subnet3. Set voice VLAN to be interface VID
Step2: setup card IP#2•www.adcom.co.th•VoIP->IP
1. Set another card with the same subnet 2 Set voice VLAN to be interface VID2. Set voice VLAN to be interface VID
Step3: setup signal/media card•www.adcom.co.th•VoIP->VoIP H248 1. Set a master card to be signal mode
2. Another card must be a media mode3 Than se a signal IP address to be a3. Than use a signal IP address to be a
Master IP
Step4: setup H.248 gateway•www.adcom.co.th•VoIP->Route
1 S t V i t dd1. Set Voice gateway addressNotice: Only set onto a signal card
Step5: setup profile•www.adcom.co.th
1. Set your softswitch IP address
•Profile ->VoIP H248
1. Set your softswitch IP address
Step6: setup H.248 interface•www.adcom.co.th•VoIP ->Interface 1. Enter H.248 interface IP
2.Set a Voice VLAN as VID.3. Signal slot is a primary.4. MG must be Enable.5 Select your H248 profile5. Select your H248 profile.6. Enter card IP as Slave
Step7: setup port terminations•www.adcom.co.th•Port -> VoIP H248
Assign a termination to each voice port (up to the MGC configuration)port (up to the MGC configuration)
Step8: port isolation•www.adcom.co.th•Switch -> Switch Setup ->Isolation
Uncheck port isolation
Step9: Verifying#1•www.adcom.co.th•statistics -> H248
Step9: Verifying#2•www.adcom.co.th
Step9: Verifying#3•www.adcom.co.th•statistics -> Port statistics
Step9: Verifying#4•www.adcom.co.th
SIP configuration guideSIP configuration guide•www.adcom.co.th
SIP configuration guideSIP configuration guideSIP introduction
SIP example
Step1: Voice VLAN setup
Step2: setup card IP
Step3: setup VoIP gateway
Step4: setup profile
Step5: setup port
Step6: setup Countrycode
Step7: port isolation
Step8: Verifying
•Advanced Comm Co., Ltd.
SIP introduction •www.adcom.co.th
•SIP •SIP
Gateway Gateway
•User A
•IP NETWORK•ANALOG •ANALOG
•User A •User B
•SIP VoIP network has no separate control i l i i lli d iunit, relying upon intelligent endpoints
SIP example•www.adcom.co.th
Step1: voice VLAN setup•www.adcom.co.th
1 S tti V i VLAN
•VLAN->VLAN
1. Setting Voice VLAN up
Step2: setup card IP •www.adcom.co.thVoIP -> IP 1.Set VoIP card’s IP
address/subnet mask2.Set a voice VLAN number as the VID 3. Set the DNS3. Set the DNS
Step3: setup VoIP gateway •www.adcom.co.thVoIP -> Route
1.Set the VoIP gateway
Step4: setup Profile•www.adcom.co.thProfile -> VoIP SIP
1.Set the SIP server IP/port2 S h R i i S IP/2. Set the Registration Server IP/port2. Set Proxy Server IP/port
Step5: setup port1 S l t SIP l t’ t•www.adcom.co.thPort -> VoIP SIP1.Select SIP slot’s port2.Enabling a port3.Set account/password4.Select a SIP profile5.Set the phone number6.A polarity should be offp y
Step6: setup Countrycode•www.adcom.co.thVoIP -> Countrycode
Step7: port isolation•www.adcom.co.th•Switch -> Switch Setup ->Isolation
Uncheck port isolation
Step8: verifying•www.adcom.co.th•statistics -> Port statistics -> Select line card
Configuration File & FirmwareConfiguration File & Firmware•www.adcom.co.th
Configuration File & FirmwareConfiguration File & Firmware
•Backup & Restore configuration file
•Factory default & reboot•Factory default & reboot
•Firmware upgrade
•Advanced Comm Co., Ltd.
Backup & Restore configuration file•www.adcom.co.th
•Maintenance -> CFG Backup
M i t CFG R t•Maintenance -> CFG Restore
Factory default & reboot•www.adcom.co.th
•Maintenance -> CFG reset
•Maintenance -> Reboot
Firmware upgrade•www.adcom.co.th
1.Check to which card, need to be upgraded
•Maintenance -> FW Upgrade
upgraded.2.Browse a firmware for that card3.Click “Upgrade” buttonN i h d fi dNotice: unmatched firmware-card type may cause a card damage.
DiagnosticDiagnostic•www.adcom.co.th
DiagnosticDiagnostic
•ADSL diagnostic
•VoIP diagnostic•VoIP diagnostic
•Advanced Comm Co., Ltd.
ADSL diagnostic•www.adcom.co.th
•Diagnostic -> LDM Test
Items: in loop diagnostic mode (LDM)Items: in loop diagnostic mode (LDM)hlog: show the channel mechanism in logarithm scaleqln: show quiet line noise in root meanqln: show quiet line noise in root mean square levelsnr: display signal to noise
VoIP diagnostic•www.adcom.co.th•Diagnostic -> MLT
Mode: in metallic line test (MLT)test - test performed from MG directlyp yRelay - In: test inner loop from external device Out: test outer loop from external device Off: prohibit relay process
Both: perform inner/outer external loop
•www.adcom.co.th
THANK YOUTHANK YOU
•Advanced Comm Co., Ltd.