Download - GPS Tracker TK102 Config
GPS Tracker TK102 Config
iPhone app: GPS Tracker TK (download from the App Store).
Track online with auto tracking, register at at: http://gps-trace.com/
Insert activated SIM card into the device (make sure SIM card is configured with caller ID on).
SMS Commands-
1. Enable TK102
To enable your tk102 gps tracker, send the command "begin+password"
Example – “begin123456”
2. Password reset
The password is important, because every command you sent to the tracker need to follow with
the password.
The default password is “123456“, and you may want to change it once you ready to use, to
change the password send a message include “password+old password new password“ to the
tracker.
Example – “password123456 567890“ will change your password from “123456” into
“567890“.
Note: password must be 6 digits long.
For the sake of this tutorial we will change the password back to default.
3. Authorization You can authorize 5 different number on the allow list, so they can command the tracker.
There is two way to authorize, one is calling, number, then this number will automatically became
one authorized number.
The most convenient way, send a message in the format of “admin+password cell phone number”
to the tracker.
Example: Send “admin123456 0432733918” will authorize phone number 0432733918 on the
allow list.
To remove a number from the allow list then send sms in the format of ”noadmin+password
cell phone number“.
Example: Send “noadmin123456 0432733918” will exclude the number 0432733918 from the
allow
list.
If you‟re authorising your tracker to call it from outside your own region (or country) then make
sure to place the area code or country in front of the number.
Example: If your tracker is in the United States, and you‟re calling the tracker from United
Kingdom, then you‟ll need to authorize your number as “61432733918” as the “61” is the
country code of United Kingdom.
Australia – 61
UK – 44
USA – 1
Find full list of country codes here.
4. Auto Tracking
This GPS have the auto tracking function. The command syntax as follow:
“t+time interval+time unit+repeat time+n+password”
This syntax seems a little bit confusing, so let me give few example for you.
*Note: In time unit, “s” stand for second, “m” stand for minute and “h” stand for Hours.
Examples:
Send auto report every 30 seconds, and repeat five times, the command is:
“t030s005n123456”
In this example, where 030 is the interval of 30 seconds, the 005 means repeat 5 time, 123456 is
the password.
Time interval and repeat time must be in 3 digits length.
If you want to set the auto tracking to report every 1 hours and repeat 24 times. Then send SMS as
“t001h024n123456“.
To cancel auto tracking, send “notn+password“.
5. Voice Surveillance
You can set the tracker into monitor mode, when you call the tracker, the tracker will answer your
phone and transfer the voice around the tracker back to you.
To set the tracker into voice surveillance mode (monitor mode), send command:
“monitor+password“, make sure to set it back to tracker mode once you want it to report
geographic info, to set it back to tracker mode send command “tracker+password“.
6. Geo-fence Geo-fence will help you to restrict the target within a certain preset area. When the target breach
the restrict area, you‟ll get a message report.
Note: You need to let the tracker stay still for 10 minutes before you send the command to it.
The command is “stockade+password latitude1, longitude1;latitude2,
longitude2“
If you are unsure of the GPS coordinates of the zone your are creating a Geo-Fence for, the
simplest way is to use Google Maps.
Go to http://maps.google.com, and find the location of the desired Geo-fence you would like to
create. In this example we will use the city of Adelaide, South Australia.
Place your cursor over the map and “right click” where you would like the top left corner of the
Geo-fence to be… and then select “What‟s here?” option.
This will reveal the exact latitude and longitude coordinates of the cursor position on the map.
The following picture will show you how it works, the restricted area is defined by the two
coordinate you set.
Copy the latitude and longitude coordinates as they appear into the first half of your Geo-fence
command.
“stockade123456 -34.922112, 138.587036;latitude2, longitude2“
Now place the cursor on the bottom right position of the Geo-fence, “right click”, select “What‟s
here?” and copy the coordinates into the last half of your command.
“stockade123456 -34.922112, 138.587036;-34.934919 138.612270
With this coordinates set in the Geo-fence command, a rectangle will be created as the boundry of
the Geo-frence.
no further North than -34.922112, South than -34.934919, East than 138.612270 and West
than 138.587036
To cancel the Geo-fence, send command “nostockade+password“.
7. Movement alert When movement alert is enable, once a movement of the target is detected ( a movement of 200
meter by default), the tracker will send a report to you, and the movement aleart will
be disable automatically.
To set a movement alert, send command “move+password“, to deactivate the alert, send
command “nomove+password“.
8. Overspeed alert This is a very useful function to monitor if the target is overspeed.
To set the overspeed alert, send command “speed+password speed”.
Example: If you need to set the speed limit to 80km/s then send command
“speed123456 080″, the speed must be in 3 digits length, and the speed unit is km/s.
Note: This is a one time alert, the alert will be deactivate once a speed breach is detected.
To cancel the alert, send command “nospeed+password”
9. IMEI number IMEI stand for “International Mobile Equipment Identity”, it‟s a unique number given to the GPS
tracker, you can acquire this number by sending the command "imei+password".
10. SOS You may already notice there is a SOS button at this tracker.
Press the SOS for 3 seconds, it‟ll send a SOS message with coordinate to all authorized number
every 3 mintues, until a SMS “help me!” is replied to the tracker.
11. Low battery alert
This is an automatically function, the GPS tracker will constantly send you a low battery alert
every 30 minutes once the voltage dropped to 3.4v.
12. Changing the system time zone
Command "time zone+password time zone"
Note: time zone is define by UTC time. Adelaide time zone is +9:30.
Example: “time zone123456 +9:30” to change the system into Adelaide time.
13. Enable SMS link mode To change the default SMS text coordinates to a link that opens the GPS coordinates on Google
Map, send the following command
“smslink+password"
To change the sms map link back to the default text coordinates, send the command
“smstext+password"
In configuration software or file of the TK-102 tracker use the following settings to connect it to
free GPS tracking system:
Configure TK102 for GPRS
In order GPS-Trace.com free GPS tracking service to correctly identify incoming data from
Xexun TK-102 tracker in the settings use following parameters:
Unique ID:
IMEI (15 digits)
Phone number: #########
Phone number of device‟s SIM card in the international format, starting from „+‟
In order to configure the object, you have to follow these steps by sending SMS commands to the
tracker:
"apn123456 mts" – sets the required apn for gprs configuration
"apnuser123456 mts" – sets the user for gprs configuration
"apnpasswd123456 mts" – sets the password for gprs configuration. For new equipment
versions user and password are set with one command "admin123456 mts mts"
"GPRS123456" – we‟re setting GPRS mode
"adminip123456 <IP> 20157" – sets the server‟s address for packages sending, <IP> replace
for IP of monitoring system
"t030s***n123456" – sets the interval of messages sending to 30 seconds. For new equipment
versions this command can have the following format "fix030s***n123456"
SMS Command List Summary
Password modification
“password+old password+space+new password”
“password123456 666888”
- the password should be 6 digitals
Authorization
“admin+password+space+cellphone number”
“admin123456 13311112222”
- there are 4 other numbers can set as the masters,use the same way to set them.
IP and Port Setting
“adminip+password+space+IP address+space+port”
“adminip123456 192.167.1.1 8899”
- When you need the tracker has the way of GPRS transferring,this is the necessary setting.
APN setting
“APN+password+space+the user's APN”
“APN123456 internet”
- When you need the tracker has the way of GPRS transferring,this is the necessary setting.And
APN refers to the GSM card‟s APN.
APN user name setting
“apnuser+password+space+apn's username”
“apnuser123456 come”
- If the APN has user name,this is the command to setting this.
APN password setting
“Apnpasswd+password+space+apn's password”
apnpasswd123456 cmet”
- If the APN has password,this is the command to setting this.
Interval tracking
“t030s005n+password
“t030s005n123456
- T=time,s=second,m=minutes,h=hour,n=times,t030s005n123456 means track 5 times for 30s
interval,
“***” means countless times.And the minimum interval time is 5 seconds(new vesion tracker),30
seconds(old vesion),the maximum times is 250 times.
Tracking mode
“tracker+password”
“tracker123456
- If you need switch the other modes to tracking mode,you need send this commands.
Track once
tracking one / or call the tracker once
tracking one
- If you want to have the tracker only report once,send tracking one to the tracker,or call the
tracker once.
Listen in mode
“monitor+password”
“monitor123456”
- If you need switch the other modes to listen in,you need send this commands. When you use the
tracker first time,call the tracker,tracker reports you the
coordinates,send “monitor123456"“,call the tracker you will hear what happen around the
tracker.
Geofence
“stockade+password+space+longitude”
“stockade123456 latitude;longitude,latitude
“22.567185,114.051248;22.555666,114.777888”
- Send this sms command to the tracker,then if the tracker run out the area you have set,it will
send “stockade”with the location to you.
Movement Alert
move+password”
“move123456”
- The tracker will move 500m at least,or you cannot get this alert.”move with the location”
Overspeed Alert
“speed+password+space+080”
“speed123456 080”
- The unit of the speed is km which is the orignal data from the GPS,and if the speed less then
30km/h,you won‟t get the alert “speed+location”
Low battery Alert
no needing to set up
No needing to set up
- When the back up battery is less than 3.7V,it will send ” L”.
Initialization
“begin+password”
“begin123456”
P.S”To cancel all the settings,you need this commands,but if you forget the password,you need
update the firmware.
IMEI Checking
“imei+password”
“imei123456”
- If you want to know the IMEI number of the tracker,you need this command.
SOS
no needing to set up
No need to set up
- When someone press the SOS,you will get the information of „help me with the coordinates”.
Ignition alert
“fortify+password”
“fortify123456”
- Only for the vehicle tracker,there are two wires connect the ACC(ignition),if you send
“fortify123456″,then anyone switch on the vehicle,it will send alert.
Ignition Status checking
“fortified+password”
“fortified123456”
- If you want to make sure that the tracker in under this function,send this commands,and tracker
will reply you.
Main power losing alert
no needing to set up
No need to set up
- If the main power is losing,the tracker will send “battery”.
Time zone setting
“Time zone+password+space+GMT time”
“Time zone123456 2”
- “UK time is time zone123456 1″currently.
Individual Website setting
“Home+pasword+space+the user's webite”
“home123456 www.tracker.com”
- If “tracker” wants make the returned sms has their domain name,they can set
“home123456 www.tracker.com”.
Relay on/off (stop engine)
“Powercar+password+space+1 (or 0)”
“Powercar123456 1”
- Only the vehicle tracker has this function,”powercar123456 1/0″ 1=on,0=off
Shake Alert(with the motion)
“shake+password+space 1-10”
“shake1234656 1”
sensor)
- Only the new version tracker has this function,from 0-10,means from shake heavily to softly,1
means the heaviest,10 means the softest.0=off
Read SD card
“Readsd+password+space+1
“readsd123456 1”
- Only the new version tracker has this function,where there is not GPRS connection,tracker
records the information into the SD card and when there comes
the GPRS connection,tracker sends all the information to the server.1=on,0=off.
SMS report
“smslinkone+password”
“smslinkone123456”
Send report in SMS (it‟s working during the gprs communication too…)
Restart tracker
“restart+password”
“restart123456”
- This command is restart the tracker.