Download - Egp Report
Company Name
Gas Authority of India Ltd.
XYZSMFLGMFLMFLDEFK360 LGT 2011
Pipeline Inspection Report
Project Name
IP-2, Sherpura to SV-6, Halol
1219.2 mm
Pipe Size
Inspection Date(s)
May 25, 2011
Report Date(s)
Aug 4, 2011
TDW Regional Office
TDW India Ltd.
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Executive Summary - Deformation
Page 1 of 1
A total of 0 deformations were detected on the inspection survey.
Inspection data was obtained for the full length (24353 meters / 24.35km) of the survey. The quality of the inspection data is satisfactory for a comprehensive assessment of this pipeline segment.
Tool Tracking By: n/a
Data Analyst: Liam FergusonVishal PatelOn-site Representative:
20.53 m/secMaximum Velocity:24,353 mPipeline Length:
0.58 m/secAverage Velocity:11.34Duration of run - Hours:
Stationing:
GPS - LAT: 22.66249 22.48802
GPS - LONG: 73.64448 73.49245
Date/Time: 5/18/2011 12:00:00 AM 5/18/2011 12:00:00 AM
Location: IP-2, Sherpura SV-6, Halol
Launcher Receiver
IP-2, Sherpura to SV-6, Halol
Mr Ranveer Singh 1219.2 mm Air - compressed
Gas Authority of India Ltd.
Deformations Detected: 0 Ovalities Detected: 0 Expansions Detected: 0 Heavy Weld Detected: 0 Valves Detected: 2
No dents found meeting minimum report parameters No dents found meeting minimum report parameters
RUN INFORMATION
INSPECTION FINDINGS
INSPECTION DETAILS
Executive S
umm
ary - Deform
ation
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Deformation Summary
The Deformation Summary Report lists all the deformations and dents detected during the inspection, sorted by depth of deformation (descending)
DEFINITIONS
Deform
ation Sum
mary
On Weld Determination whether the indication crosses a girth (or seam) weld.
Description Text describing a deformation in greater detail. Any special conditions are noted.
Metal Loss "Yes" is listed if there is any metal loss associated with a dent.
Distance from Defect The distance to the upstream and downstream reference listed in the previous column. Used for locating defects in the field.
Above-Ground References
The name of the closest upstream and downstream references, usually either an AGM or a valve.
Min X Sec Dia The minimum measured Cross-Section (ID) measured within the scope of the deformation.
Distance Given in either feet or meters, based on contractual agreements, this is the absolute distance measured by the tool from launch.
ID# Each Deformation is automatically assigned a number in the software. This number is provided to assist the user of PIGTRAP software to more easily find any given defect.
Depth Depth of the indication in inches or mm.
Sub Type The sub type of deformation if other than dent (i.e. Heavy Weld, Ovality, Buckle, Expansion).
Orientation The orientation of the deformation indication in degrees (top of pipe = 0) and clock position, as viewed facing downstream.
Dents may affect the integrity of the pipeline and are considered harmful. A dent with associated metal loss is potentially more significant than a dent alone.
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Deformation Summary
Page 2 of 2
No Dents have been detected on this pipeline inspection
ID#Distance
(m)Depth (mm)
Depth %
Orientation(Deg / O’Clock) Sub Type
Min X Sec
Dia DescriptionOn
WeldMetal Loss Above-Ground References
Distance from
Defect
Deform
ation Sum
mary
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Charts
The Pipeline Summary report provides an overview of the pipeline condition.
The following charts are utilized in this report:
Dent Orientation The distance from launch is plotted against the orientation of the deformation indications. Orientation is based on 360° in a circle, with 0°or 360° marking the top of the pipe (180° the bottom).
Dent Depth This chart highlights the predicted depths of deformations in inches or mm compared to distance.
Velocity - DEF Displays the speed of the tool relative to distance during the inspection. The specified contractual velocity of the inspection tool is 0 feet per second. If the tool exceeds this speed, the data collected by the tool may be degraded.
CHARTS
Charts
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Velocity Graph - DEF
Velocity G
raph - DE
F
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Dent Depth Graph
No dents found meeting minimum report parameters.
Dent D
epth Graph
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Dent Orientation Graph
8:00 O’Clock
4:00 O’Clock
No dents found meeting minimum report parameters.
Dent O
rientation Graph
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Locations Summary
A location is a feature in the pipeline that can be used to correlate the inspection tool data to above ground references. Common location features include valves, fittings, flanges, tees, casings, repairs and aboveground markers (AGMs).
For example, a metal loss area could be referenced as being 200 feet down stream from a valve. Not all locations can be easily found from above ground. Some locations might not be useful if they are not above ground.
Description Describes the location in greater detail. Possible entries include valves, flanges, fittings, tees, markers, etc.
D/S Weld Dist. The distance to the downstream (D/S) weld (in feet or meters).
Longitude This shows the east/west position of the Location as supplied by the customer or recorded by an AGM box. For XYZ mapping runs, these values are the supplied survey points or were calculated by the tool.
Latitude This shows the north/south position of the Location as supplied by the customer or recorded by an AGM box. For XYZ mapping runs, these values are the supplied survey points or were calculated by the tool.
U/S Weld Dist. The distance to the upstream (U/S) weld (in feet or meters).
Time A reference time from the inspection tool. May also be used to locate features in the PIGTRAP software.
ID# Each location is automatically assigned a number in the software. This number is provided to assist the user of PIGTRAP software to more easily find any given defect.
Joint # This unique number identifies the girth weld number.
Distance Given in either feet or meters, based on contractual agreements, this is the absolute distance measured by the tool from launch.
Zeroes in Latitude and Longitude mean that no data was supplied by the customer. Calculated or estimated values can be viewed in the Pipe Listing report.
Locations Sum
mary
DEFINITIONS
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Locations Summary
Page 2 of 2
10000005 74,899.81 24,353.7 20,890 5.1 5.4 Valve (Receiver), SV-6 Halol 22.48802 73.49245
10000003 55,569.75 13,449.4 11,570 1.3 4.5 Bend right 0.00000 0.00000
10000004 56,033.85 13,721.3 11,810 2.2 5.9 Bend right 0.00000 0.00000
10000002 36,209.47 874.9 860 2.0 3.8 Bend right 0.00000 0.00000
10000000 34,069.78 0.0 110 0.3 0.2 Valve (Launcher), IP-2 Sherpura 22.66249 73.64448
10000001 35,557.54 585.7 600 2.8 5.5 Bend left 0.00000 0.00000
ID# Time Dist (m) Joint #U/S Weld
Dist.D/S Weld
Dist. Description Latitude Longitude
Repair 0
Marker 0
Tee 0
Pipe Support 0
Valve 2
Bend 4
Type Number
Casing 0
Fitting 0
Flange 0
Locations Sum
mary
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Nominal Wall ThicknessDEFINITIONS
Nom
inal Wall T
hickness
The following list provides locations along the pipeline where changes in wall thickness or pipe type occur. While the TDW inspection tool can easily detect changes in wall thickness, it cannot take direct thickness measurements. Therefore, where wall thicknesses are known, the tool can identify the locations where the thickness changes. Where wall thicknesses are not known, best efforts will be made to estimate thicknesses based on best available data.
Yield Strength (SMYS)
Specified Minimum Yield Strength – A required strength level that measured yield stress of a pipe material must exceed, which is a function of pipe grade. The measured yield stress is the tensile stress required to produce a total elongation of 0.5 percent of a gage length as determined by an extensometer during a tensile test.
Safety Factor(or design factor) Typically 0.72 per ASME B31.4 In setting the safety factor, due consideration has been given to and allowances made for the manufacturing tolerance and maximum allowable depth of imperfections provided for in the specifications.
Length of Segment The length of the pipe for the specified wall thickness, measured in feet or meters.
Pipetype Type of pipe construction. Electric Resistance Weld (ERW), Seamless (SMLS), Lap Weld (LW), etc.
ID# Each wall thickness change ID is automatically assigned a number in the software. This number is provided to assist the user of PIGTRAP software to more easily find any given defect.
Distance Given in either feet or meters, based on contractual agreements, this is the absolute distance measured by the tool from launch.
Wall Thickness The predicted wall thickness in inches or millimeters.
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Nominal Wall Thickness
Page 2 of 3
11000024 13716.52 23.80 ERW 70000 0.72 8.15
11000023 13679.92 15.90 ERW 70000 0.72 36.60
11000026 15312.29 25.00 ERW 70000 0.72 37.55
11000025 13724.67 15.90 ERW 70000 0.72 1,587.62
11000022 13531.77 23.80 ERW 70000 0.72 148.15
11000019 13002.67 15.90 ERW 70000 0.72 444.13
11000018 12977.91 23.80 ERW 70000 0.72 24.76
11000021 13452.33 15.90 ERW 70000 0.72 79.44
11000020 13446.80 23.80 ERW 70000 0.72 5.52
11000032 16606.14 25.00 ERW 70000 0.72 12.30
11000031 16220.20 15.90 ERW 70000 0.72 385.94
11000028 15744.79 25.00 ERW 70000 0.72 37.32
11000027 15349.84 15.90 ERW 70000 0.72 394.95
11000030 16195.19 25.00 ERW 70000 0.72 25.01
11000029 15782.12 15.90 ERW 70000 0.72 413.07
11000005 2614.12 23.80 ERW 70000 0.72 37.51
11000004 877.13 17.50 ERW 70000 0.72 1,736.99
11000007 2658.28 15.90 ERW 70000 0.72 601.08
11000006 2651.63 17.50 ERW 70000 0.72 6.65
11000003 871.27 23.80 ERW 70000 0.72 5.86
11000000 -0.29 17.50 ERW 70000 0.72 581.70
11000017 7424.02 15.90 ERW 70000 0.72 5,553.89
11000002 589.69 17.50 ERW 70000 0.72 281.58
11000001 581.42 25.00 ERW 70000 0.72 8.28
11000014 4724.18 17.50 ERW 70000 0.72 352.84
11000013 4638.02 23.80 ERW 70000 0.72 86.17
11000016 5714.37 17.50 ERW 70000 0.72 1,709.64
11000015 5077.03 23.80 ERW 70000 0.72 637.35
11000012 4085.56 17.50 ERW 70000 0.72 552.46
11000009 3480.15 23.80 ERW 70000 0.72 23.94
11000008 3259.37 17.50 ERW 70000 0.72 220.78
11000011 4048.39 23.80 ERW 70000 0.72 37.17
11000010 3504.09 17.50 ERW 70000 0.72 544.30
ID# Distance (m)Wall Thickness (mm) Pipetype
Yield Strength (SMYS) Safety Factor
Length of Segment (m) N
ominal W
all Thickness
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Nominal Wall Thickness
Page 3 of 3
11000033 16618.44 15.90 ERW 70000 0.72 1,297.84
11000035 21446.27 15.90 ERW 70000 0.72 2,728.18
11000034 17916.29 23.80 ERW 70000 0.72 3,529.98
11000036 24174.45 23.80 ERW 70000 0.72 179.28
ID# Distance (m)Wall Thickness (mm) Pipetype
Yield Strength (SMYS) Safety Factor
Length of Segment (m)
25.00 ERW 120 0.120 0.5%
23.80 ERW 4,724 4.724 19.4%
17.50 ERW 5,987 5.987 24.6%
15.90 ERW 13,523 13.523 55.5%
Wall Thickness Pipetype Total Length (m)Total Length (kilometers) Percent of Total Distance
Nom
inal Wall T
hickness
Repair ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Pipeline repairs that are typically detected include:
This table lists all the repairs to the pipeline detected during the inspection.
Repair R
eport
Definition
Length Gives the linear length of the repair.
Type of Repair Describes the type of repair detected during the inspection.
ID# Each repair is automatically assigned a number in the software. This number is provided to assist the user of PIGTRAP software to more easily find any given defect.
Distance Given in either feet or meters, based on contractual agreements, this is the absolute distance measured by the tool from launch.
- Clamps
- Weld + End
- Clock Spring
- Stopples
- Sleeves
- Half sole
- Patches
Repair ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 2 of 2
No Repairs have been detected on this pipeline inspection
ID# Distance (m) Length (m) Type of Repair Repair R
eport
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc
AGM Information SummaryDEFINITIONS
Description Describes the AGM in greater detail. Generally includes only valves and markers.
Latitude This shows the north/south position of the Location as supplied by the customer or recorded by an AGM box. For XYZ mapping runs, these values are the supplied survey points or were calculated by the tool.
Longitude This shows the east/west position of the Location as supplied by the customer or recorded by an AGM box. For XYZ mapping runs, these values are the supplied survey points or were calculated by the tool.
ID# Each location is automatically assigned a number in the software. This number is provided to assist the user of PIGTRAP software to more easily find any given defect.
Time A reference time from the inspection tool. May also be used to locate features in the PIGTRAP software.
Distance Given in either feet or meters, based on contractual agreements, this is the absolute distance measured by the tool from launch.
This table includes all values and above ground marker sites in the inspection run.
AG
M Inform
ation Sum
mary
Zeroes in Latitude and Longitude mean that no data was supplied by the customer. Calculated or estimated values can be viewed in the Pipe Listing report.
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc
AGM Information Summary
Page 2 of 2
Markers 0
Valves 2
TYPE NUMBER
10000005 74899.81 24353.73 Valve (Receiver), SV-6 Halol 22.48802000 73.49245000
10000000 34069.78 0.00 Valve (Launcher), IP-2 Sherpura 22.66249000 73.64448000
ID# Time Distance(m) Description Latitude Longitude
AG
M Inform
ation Sum
mary
TDW Services, Inc.
Gas Authority of India Ltd.
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Miscellaneous
Distance Given in either feet or meters, based on contractual agreements, this is the absolute distance measured by the tool from launch.
Memo A description of the entry.
ID# Each miscellaneous note is automatically assigned a number in the software. This number is provided to assist the user of PIGTRAP software to more easily find any given defect.
Time A reference time from the inspection tool. May also be used to locate features in the PIGTRAP software.
There are occasions when special notations or circumstances require the addition of a note. These notes are included in this table for your reference.
DEFINITIONS
Miscellaneous
Sensor problems
Noting locations where anomalous sensor readings occurred.
Tool stops/starts
All tools are setup on a time-based system. When the tool stops, it continues to record, although not moving. When the tool moves very slowly, it is possible that its movement is not detected, and therefore, reported distances may appear shorter than actual. Many stops and starts may affect the overall distance accuracy of the tool.
Mill anomaly The process of manufacturing pipe can often leave indications in the pipe wall. Typically these anomalies are not detrimental, and are identified for the benefit of the client.
Gap or dent in casing
When the casing is not welded, or when a gap occurs in the weld, this signature is detected by the tool, and identified with a Misc. remark.
Inclusion An anomaly in the cross section of the pipeline. Inclusions may be detrimental if they protrude through the pipe wall.
MEMO EXAMPLES
TDW Services, Inc.
Gas Authority of India Ltd.
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Miscellaneous
Page 2 of 2
12000001 85,283.14 24,365.30 End Run Tickle
12000000 443.38 -9.57 Begin Run Tickle
ID# Time Distance (m) Memo
Misc listings 2
Total Number
Miscellaneous
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
% Depth Predicted depth of the defect as a percentage of nominal wall.
Orientation: Deg. / O'Clock
Orientation is reported in degrees or o’clock (0 degrees/12:00 at top of pipe) as viewed looking downstream.
Longitude If GPS coordinates were provided for launch, receive and AGMs, this provides the predicted Longitude reading of the location from the first GPS reading based on INS readings obtained by the tool during the inspection.
Length or Pipe Thickness
Predicted length of the defect, reported in either inches or millimeters – or if a wall thickness change, the new wall thickness begins at this point.
% Est. Press. (P'/P) or Temp. Factor
Percent of maximum established pressure, this is calculated by dividing the calculated safe pressure of the defect (P') by the current established maximum operating pressure of the pipeline (P). For Magpie reporting, P is either established MOP provided by the customer or the calculated pressure rating for the pipe (P). Percentages less than 100% are considered pressure reducing.
P' (Calc. Safe Max. Operating Pressure)
or Safety Factor
Calculated safe maximum operating pressure for the pipeline segment as calculated based on information provided by the Customer. Magpie software uses either ASME B31G, MODIFIED ASME B31G or Z662-99 to calculate the calculated safe maximum allowable operating pressure (P’) of the pipeline at a metal loss area.
Width or Yield Strength
Predicted width of the defect, reported in either inches or millimeters – or if a wall thickness change, the new SMYS begins at this point.
Distance Given in either feet or meters, based on contractual agreements, this is the absolute distance from launch.
Description Describes the event at the particular location. Identifies the type of the descriptive, being a weld, location, pipe thickness change, etc.
ID# Each item is automatically assigned a number in the software. This number is provided to assist the user of PIGTRAP software to more easily find any given defect.
Joint # This unique number identifies the girth weld number.
Latitude If GPS coordinates were provided for launch, receive and AGMs, this provides the predicted Latitude reading of the location from the first GPS reading based on INS readings obtained by the tool during the inspection.
D/S Weld Dist. The distance to the downstream (D/S) weld (in feet or meters).
U/S Weld Dist. The distance to the upstream (U/S) weld (in feet or meters).
The Pipeline Listing Report presents all detected pipeline data in sequential order, beginning at launcher and ending at the receiver. The table includes welds, locations, metal loss defects, AGMs, wall thickness changes, etc.
DEFINITIONS
Pipeline Listing R
eport
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 2 of 73Criteria:
290 WELD 194.6 290 0.0 11.9 22.66388802 73.64631947
280 WELD 182.7 280 0.0 11.8 22.66348979 73.64650775
310 WELD 219.8 310 0.0 12.1 22.66455603 73.64565344
300 WELD 206.4 300 0.0 13.4 22.66425779 73.64603514
250 WELD 146.6 250 0.0 11.8 22.66229787 73.64643617
240 WELD 134.3 240 0.0 12.2 22.66194252 73.64622297
270 WELD 170.6 270 0.0 12.1 22.66307087 73.64658716
260 WELD 158.3 260 0.0 12.3 22.66267749 73.64655836
360 WELD 280.6 360 0.0 13.1 22.66390414 73.64224743
330 WELD 244.1 330 0.0 10.1 22.66489669 73.64452445
320 WELD 231.9 320 0.0 12.2 22.66479361 73.64510237
350 WELD 267.2 350 0.0 13.4 22.66464991 73.64317940
340 WELD 254.3 340 0.0 12.9 22.66485255 73.64385149
230 WELD 121.4 230 0.0 12.9 22.66166789 73.64593727
120 WELD 0.2 120 0.0 1.3 22.66258139 73.64446161
10000000 Valve (Launcher), IP-2 Sherpura
0.0 110 0.3 0.2 22.66249000 73.64448000
140 WELD 9.0 140 0.0 13.8 22.66276811 73.64438160
130 WELD 1.6 130 0.0 7.4 22.66267392 73.64443788
12000000 Begin Run Tickle -9.6 0 - 9.3 0.00000000 0.00000000
110 WELD -0.3 110 0.0 0.5 0.00000000 0.00000000
11000000 WT CHANGE -0.3 110 0.0 0.0 0.00000000 0.00000000 17.50 70000 0.72
200 WELD 85.0 200 0.0 13.1 22.66133977 73.64483059
190 WELD 72.6 190 0.0 12.4 22.66144135 73.64445413
220 WELD 109.1 220 0.0 12.3 22.66149372 73.64562666
210 WELD 98.2 210 0.0 10.9 22.66135735 73.64522820
160 WELD 35.1 160 0.0 12.6 22.66234493 73.64382676
150 WELD 22.7 150 0.0 12.4 22.66275682 73.64409020
180 WELD 60.0 180 0.0 12.6 22.66164446 73.64412422
170 WELD 47.7 170 0.0 12.3 22.66195931 73.64387666
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 3 of 73Criteria:
370 WELD 293.7 370 0.0 12.4 22.66214821 73.64173042
390 WELD 318.7 390 0.0 13.6 22.65974231 73.64371527
380 WELD 306.1 380 0.0 12.6 22.66042705 73.64263185
10000001 Bend left 585.7 600 2.8 5.5 22.65920285 73.65101962 0 12:00
600 WELD 581.4 600 0.0 8.3 22.65920499 73.65101871
610 WELD 589.7 610 0.0 10.5 22.65898335 73.65111346
11000002 WT CHANGE 589.7 610 0.0 0.0 22.65919868 73.65102140 17.50 70000 0.72
580 WELD 556.8 580 0.0 12.7 22.65954397 73.65071865
570 WELD 544.1 570 0.0 12.8 22.65965529 73.65052805
11000001 WT CHANGE 581.4 600 0.0 8.3 22.65937498 73.65088174 25.00 70000 0.72
590 WELD 569.5 590 0.0 11.9 22.65938280 73.65087544
630 WELD 612.8 630 0.0 9.2 22.65872635 73.65138811
620 WELD 600.2 620 0.0 12.6 22.65887194 73.65125068
560 WELD 531.1 560 0.0 13.0 22.65972243 73.65031614
450 WELD 391.3 450 0.0 12.6 22.65945846 73.64715388
440 WELD 379.5 440 0.0 11.8 22.65939712 73.64673095
470 WELD 416.4 470 0.0 12.2 22.65957509 73.64787148
460 WELD 403.9 460 0.0 12.5 22.65949871 73.64750504
410 WELD 345.1 410 0.0 11.7 22.65941163 73.64539139
400 WELD 332.2 400 0.0 12.9 22.65948686 73.64463566
430 WELD 366.9 430 0.0 12.6 22.65938872 73.64637013
420 WELD 356.8 420 0.0 10.1 22.65939467 73.64594451
530 WELD 492.2 530 0.0 13.1 22.65978704 73.64959086
520 WELD 478.8 520 0.0 13.3 22.65978598 73.64934141
550 WELD 518.4 550 0.0 12.7 22.65975794 73.65008371
540 WELD 505.3 540 0.0 13.1 22.65977135 73.64983881
490 WELD 441.2 490 0.0 12.5 22.65966179 73.64848860
480 WELD 428.6 480 0.0 12.6 22.65963539 73.64820103
510 WELD 466.4 510 0.0 12.5 22.65975278 73.64906759
500 WELD 453.6 500 0.0 12.7 22.65970656 73.64878287
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 4 of 73Criteria:
890 WELD 901.4 890 0.0 12.2 22.65523486 73.65171012
880 WELD 889.1 880 0.0 12.3 22.65548418 73.65169875
900 WELD 913.6 900 0.0 8.4 22.65497822 73.65171222
10000002 Bend right 874.9 860 2.0 3.8 22.65568465 73.65153448 0 12:00
860 WELD 871.3 860 0.0 5.8 22.65568524 73.65153278
870 WELD 877.2 870 0.0 11.9 22.65564202 73.65165850
11000004 WT CHANGE 877.1 870 0.0 0.0 22.65568358 73.65153760 17.50 70000 0.72
11000003 WT CHANGE 871.3 860 0.0 0.1 22.65544553 73.65111843 23.80 70000 0.72
750 WELD 746.8 750 0.0 12.9 22.65596942 73.65144307
740 WELD 733.7 740 0.0 13.0 22.65614503 73.65149423
770 WELD 772.3 770 0.0 12.9 22.65547831 73.65102473
760 WELD 759.6 760 0.0 12.7 22.65572266 73.65123907
710 WELD 702.7 710 0.0 12.4 22.65700361 73.65191051
700 WELD 690.5 700 0.0 12.2 22.65731414 73.65196585
730 WELD 727.4 730 0.0 6.3 22.65642474 73.65165377
720 WELD 715.1 720 0.0 12.3 22.65670801 73.65180232
830 WELD 849.7 830 0.0 5.7 22.65520909 73.65067671
820 WELD 836.6 820 0.0 13.1 22.65503686 73.65041227
850 WELD 868.7 850 0.0 2.6 22.65544441 73.65111650
840 WELD 855.4 840 0.0 13.3 22.65539610 73.65095438
790 WELD 797.7 790 0.0 12.5 22.65514054 73.65062754
780 WELD 785.2 780 0.0 12.5 22.65531277 73.65083552
810 WELD 823.3 810 0.0 13.4 22.65498067 73.65036647
800 WELD 810.2 800 0.0 13.1 22.65506297 73.65050210
670 WELD 659.8 670 0.0 3.8 22.65801761 73.65187947
660 WELD 646.6 660 0.0 13.2 22.65822508 73.65177716
690 WELD 677.4 690 0.0 13.1 22.65761689 73.65197089
680 WELD 663.6 680 0.0 13.8 22.65773599 73.65190605
650 WELD 634.4 650 0.0 12.3 22.65840509 73.65164671
640 WELD 622.0 640 0.0 12.4 22.65855277 73.65152804
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 5 of 73Criteria:
910 WELD 922.0 910 0.0 10.7 22.65472355 73.65170887
970 WELD 983.9 970 0.0 11.7 22.65331096 73.65134312
960 WELD 969.7 960 0.0 14.2 22.65363593 73.65156160
990 WELD 1,007.6 990 0.0 12.5 22.65269090 73.65075926
980 WELD 995.6 980 0.0 12.0 22.65296974 73.65103545
930 WELD 941.4 930 0.0 4.8 22.65428623 73.65171008
920 WELD 932.8 920 0.0 8.6 22.65452795 73.65172815
950 WELD 956.8 950 0.0 12.9 22.65391695 73.65169848
940 WELD 946.2 940 0.0 10.6 22.65408075 73.65170940
1180 WELD 1,235.5 1180 0.0 11.8 22.65159030 73.64962963
1170 WELD 1,223.8 1170 0.0 11.7 22.65142670 73.64899851
1200 WELD 1,258.7 1200 0.0 11.7 22.65189933 73.65089842
1190 WELD 1,247.3 1190 0.0 11.4 22.65176755 73.65029561
1160 WELD 1,212.2 1160 0.0 11.6 22.65128974 73.64838106
1050 WELD 1,080.9 1050 0.0 12.2 22.65144117 73.64878301
1040 WELD 1,068.2 1040 0.0 12.7 22.65158576 73.64909980
1070 WELD 1,106.4 1070 0.0 12.7 22.65123369 73.64818288
1060 WELD 1,093.2 1060 0.0 13.2 22.65132327 73.64846131
1010 WELD 1,031.8 1010 0.0 12.5 22.65217394 73.65011401
1000 WELD 1,020.1 1000 0.0 11.6 22.65242389 73.65045196
1030 WELD 1,056.5 1030 0.0 11.7 22.65175795 73.64944209
1020 WELD 1,044.2 1020 0.0 12.3 22.65195639 73.64979199
1130 WELD 1,177.2 1130 0.0 11.5 22.65106643 73.64732162
1120 WELD 1,165.8 1120 0.0 11.3 22.65106596 73.64735135
1150 WELD 1,200.4 1150 0.0 11.8 22.65118223 73.64785699
1140 WELD 1,188.7 1140 0.0 11.7 22.65110949 73.64751355
1090 WELD 1,131.7 1090 0.0 11.6 22.65110899 73.64765971
1080 WELD 1,119.1 1080 0.0 12.6 22.65115990 73.64789509
1110 WELD 1,154.5 1110 0.0 11.3 22.65106571 73.64737845
1100 WELD 1,143.3 1100 0.0 11.2 22.65108689 73.64750410
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 6 of 73Criteria:
1220 WELD 1,282.2 1220 0.0 11.6 22.65204547 73.65185570
1210 WELD 1,270.4 1210 0.0 11.8 22.65199843 73.65141962
1240 WELD 1,305.3 1240 0.0 11.4 22.65178028 73.65218646
1230 WELD 1,293.8 1230 0.0 11.5 22.65196029 73.65209791
1300 WELD 1,374.4 1300 0.0 11.7 22.64992249 73.65078202
1290 WELD 1,362.7 1290 0.0 11.7 22.65024020 73.65112060
1320 WELD 1,397.6 1320 0.0 11.4 22.64931156 73.65001597
1310 WELD 1,386.1 1310 0.0 11.5 22.64961193 73.65041467
1260 WELD 1,328.3 1260 0.0 11.5 22.65122461 73.65197884
1250 WELD 1,316.6 1250 0.0 11.7 22.65153438 73.65215565
1280 WELD 1,351.1 1280 0.0 11.6 22.65056277 73.65143866
1270 WELD 1,339.8 1270 0.0 11.3 22.65089999 73.65175064
1330 WELD 1,409.0 1330 0.0 11.9 22.64902959 73.64959669
1500 WELD 1,606.6 1500 0.0 11.7 22.64759936 73.64539659
1390 WELD 1,478.2 1390 0.0 11.8 22.64781275 73.64664482
1380 WELD 1,466.4 1380 0.0 11.8 22.64794750 73.64715221
1410 WELD 1,501.7 1410 0.0 11.8 22.64764888 73.64568592
1400 WELD 1,490.0 1400 0.0 11.7 22.64771587 73.64614792
1350 WELD 1,432.3 1350 0.0 11.3 22.64852169 73.64865097
1340 WELD 1,420.9 1340 0.0 11.4 22.64876967 73.64914658
1370 WELD 1,455.0 1370 0.0 11.4 22.64811107 73.64765973
1360 WELD 1,443.6 1360 0.0 11.3 22.64830380 73.64815943
1470 WELD 1,571.8 1470 0.0 11.7 22.64759165 73.64427894
1460 WELD 1,560.4 1460 0.0 11.4 22.64758040 73.64420016
1490 WELD 1,595.2 1490 0.0 11.4 22.64759811 73.64482000
1480 WELD 1,583.5 1480 0.0 11.7 22.64759461 73.64448337
1430 WELD 1,525.2 1430 0.0 11.4 22.64757874 73.64487628
1420 WELD 1,513.5 1420 0.0 11.6 22.64759740 73.64523000
1450 WELD 1,548.4 1450 0.0 12.0 22.64756862 73.64427382
1440 WELD 1,536.6 1440 0.0 11.8 22.64756890 73.64454238
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 7 of 73Criteria:
1560 WELD 1,677.3 1560 0.0 11.7 22.64763776 73.64985223
1550 WELD 1,665.6 1550 0.0 11.7 22.64767987 73.64935479
1580 WELD 1,700.8 1580 0.0 11.7 22.64745635 73.65052675
1570 WELD 1,689.0 1570 0.0 11.7 22.64756739 73.65024815
1520 WELD 1,630.3 1520 0.0 11.7 22.64761219 73.64703342
1510 WELD 1,618.3 1510 0.0 12.0 22.64760015 73.64616859
1540 WELD 1,653.7 1540 0.0 11.8 22.64766192 73.64866748
1530 WELD 1,642.0 1530 0.0 11.7 22.64763489 73.64788998
1640 WELD 1,770.6 1640 0.0 11.8 22.64610420 73.65007878
1630 WELD 1,758.9 1630 0.0 11.7 22.64635955 73.65028479
1660 WELD 1,794.2 1660 0.0 11.7 22.64558999 73.64960409
1650 WELD 1,782.4 1650 0.0 11.8 22.64584681 73.64985029
1600 WELD 1,724.2 1600 0.0 11.7 22.64710006 73.65070508
1590 WELD 1,712.5 1590 0.0 11.8 22.64730650 73.65069749
1620 WELD 1,747.4 1620 0.0 11.5 22.64661325 73.65047008
1610 WELD 1,736.0 1610 0.0 11.4 22.64685621 73.65059083
1720 WELD 1,863.8 1720 0.0 11.4 22.64422774 73.64669618
1710 WELD 1,852.0 1710 0.0 11.8 22.64440762 73.64727031
1740 WELD 1,886.7 1740 0.0 11.3 22.64397773 73.64552316
1730 WELD 1,875.2 1730 0.0 11.5 22.64408652 73.64610043
1680 WELD 1,817.6 1680 0.0 11.6 22.64506579 73.64876177
1670 WELD 1,805.9 1670 0.0 11.7 22.64532267 73.64920073
1700 WELD 1,840.3 1700 0.0 11.7 22.64459731 73.64780466
1690 WELD 1,829.2 1690 0.0 11.1 22.64482047 73.64831829
1800 WELD 1,955.8 1800 0.0 11.4 22.64382083 73.64259851
1790 WELD 1,944.5 1790 0.0 11.3 22.64379852 73.64290875
1760 WELD 1,909.8 1760 0.0 11.3 22.64382868 73.64438139
1750 WELD 1,898.1 1750 0.0 11.7 22.64388526 73.64493264
1780 WELD 1,932.9 1780 0.0 11.6 22.64378483 73.64332973
1770 WELD 1,921.1 1770 0.0 11.8 22.64379970 73.64384411
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 8 of 73Criteria:
2050 WELD 2,246.2 2050 0.0 11.2 22.64179766 73.64585425
2040 WELD 2,234.8 2040 0.0 11.4 22.64189114 73.64508114
2070 WELD 2,268.8 2070 0.0 14.2 22.64163118 73.64728142
2060 WELD 2,257.3 2060 0.0 11.5 22.64171406 73.64660912
2010 WELD 2,201.0 2010 0.0 11.6 22.64193223 73.64386054
2000 WELD 2,186.9 2000 0.0 14.2 22.64192278 73.64402133
2030 WELD 2,223.8 2030 0.0 11.0 22.64195327 73.64428733
2020 WELD 2,212.6 2020 0.0 11.1 22.64196394 73.64388086
2090 WELD 2,296.3 2090 0.0 11.4 22.64124941 73.64749661
2080 WELD 2,283.1 2080 0.0 13.2 22.64148320 73.64761517
2100 WELD 2,307.7 2100 0.0 11.6 22.64101281 73.64720677
1890 WELD 2,059.9 1890 0.0 12.1 22.64342708 73.64645019
1880 WELD 2,048.3 1880 0.0 11.6 22.64352919 73.64576263
1910 WELD 2,083.0 1910 0.0 11.6 22.64319280 73.64750041
1900 WELD 2,072.0 1900 0.0 11.0 22.64331944 73.64703334
1850 WELD 2,013.4 1850 0.0 11.8 22.64374011 73.64350317
1840 WELD 2,002.2 1840 0.0 11.2 22.64380064 73.64289142
1870 WELD 2,036.7 1870 0.0 11.6 22.64361888 73.64496899
1860 WELD 2,025.2 1860 0.0 11.5 22.64368229 73.64415546
1970 WELD 2,152.1 1970 0.0 11.5 22.64203192 73.64558307
1960 WELD 2,141.2 1960 0.0 11.0 22.64217798 73.64624409
1990 WELD 2,175.4 1990 0.0 11.5 22.64192128 73.64439497
1980 WELD 2,163.6 1980 0.0 11.8 22.64195499 73.64495693
1930 WELD 2,106.2 1930 0.0 11.5 22.64281768 73.64759413
1920 WELD 2,094.5 1920 0.0 11.7 22.64301999 73.64763675
1950 WELD 2,130.1 1950 0.0 11.0 22.64237480 73.64692656
1940 WELD 2,117.7 1940 0.0 12.4 22.64259598 73.64735602
1830 WELD 1,990.3 1830 0.0 11.9 22.64385031 73.64243296
1820 WELD 1,978.7 1820 0.0 11.6 22.64385550 73.64230705
1810 WELD 1,967.3 1810 0.0 11.5 22.64384358 73.64235038
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 9 of 73Criteria:
2220 WELD 2,453.7 2220 0.0 11.7 22.64013294 73.64702938
2210 WELD 2,439.8 2210 0.0 14.0 22.64023931 73.64619162
2240 WELD 2,476.6 2240 0.0 11.2 22.63969297 73.64661688
2230 WELD 2,465.4 2230 0.0 11.2 22.63990902 73.64695511
2180 WELD 2,400.1 2180 0.0 11.3 22.64046364 73.64362320
2170 WELD 2,388.5 2170 0.0 11.6 22.64045880 73.64352894
2200 WELD 2,425.5 2200 0.0 14.2 22.64032975 73.64517065
2190 WELD 2,411.4 2190 0.0 14.1 22.64042310 73.64429780
2300 WELD 2,548.5 2300 0.0 11.5 22.63916562 73.64281765
2290 WELD 2,537.1 2290 0.0 11.4 22.63915619 73.64282051
2320 WELD 2,571.9 2320 0.0 11.6 22.63915438 73.64318985
2310 WELD 2,560.0 2310 0.0 11.9 22.63917122 73.64285087
2260 WELD 2,499.2 2260 0.0 12.1 22.63934457 73.64522560
2250 WELD 2,487.8 2250 0.0 11.4 22.63950670 73.64593429
2280 WELD 2,525.5 2280 0.0 11.6 22.63914038 73.64365139
2270 WELD 2,511.3 2270 0.0 14.2 22.63920534 73.64448973
2160 WELD 2,377.0 2160 0.0 11.5 22.64045109 73.64352590
2130 WELD 2,342.4 2130 0.0 11.7 22.64052660 73.64518215
2120 WELD 2,330.9 2120 0.0 11.6 22.64062695 73.64591291
2150 WELD 2,365.5 2150 0.0 11.4 22.64044484 73.64391764
2140 WELD 2,354.1 2140 0.0 11.4 22.64045693 73.64445896
2110 WELD 2,319.3 2110 0.0 11.5 22.64080409 73.64661135
2370 WELD 2,626.7 2370 0.0 11.7 22.63892634 73.64660040
2360 WELD 2,614.1 2360 0.0 12.6 22.63906323 73.64649042
2390 WELD 2,646.2 2390 0.0 5.5 22.63899265 73.64711817
2380 WELD 2,638.4 2380 0.0 7.8 22.63895798 73.64679227
2340 WELD 2,595.3 2340 0.0 12.9 22.63905327 73.64476854
2330 WELD 2,583.5 2330 0.0 11.8 22.63909980 73.64394255
11000005 WT CHANGE 2,614.1 2360 0.0 0.0 22.63904303 73.64556143 23.80 70000 0.72
2350 WELD 2,608.2 2350 0.0 6.0 22.63904292 73.64555614
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 10 of 73Criteria:
2650 WELD 2,933.6 2650 0.0 12.1 22.63495829 73.64457919
2640 WELD 2,922.0 2640 0.0 11.6 22.63495127 73.64465313
2670 WELD 2,956.6 2670 0.0 11.5 22.63488043 73.64581797
2660 WELD 2,945.7 2660 0.0 10.8 22.63495717 73.64498352
2630 WELD 2,910.5 2630 0.0 11.4 22.63501052 73.64533502
2520 WELD 2,782.7 2520 0.0 11.1 22.63737780 73.65087233
2510 WELD 2,771.2 2510 0.0 11.5 22.63762895 73.65117418
2540 WELD 2,804.7 2540 0.0 11.6 22.63687268 73.65020391
2530 WELD 2,793.8 2530 0.0 11.0 22.63711333 73.65048536
2480 WELD 2,738.2 2480 0.0 11.0 22.63810061 73.65068092
2470 WELD 2,726.8 2470 0.0 11.3 22.63819207 73.65024494
2500 WELD 2,760.3 2500 0.0 10.9 22.63783733 73.65122665
2490 WELD 2,749.2 2490 0.0 11.1 22.63798916 73.65104005
2600 WELD 2,873.3 2600 0.0 14.2 22.63549335 73.64761746
2590 WELD 2,861.9 2590 0.0 11.4 22.63570153 73.64823494
2620 WELD 2,898.9 2620 0.0 11.7 22.63513392 73.64606767
2610 WELD 2,887.5 2610 0.0 11.4 22.63530059 73.64696125
2560 WELD 2,827.7 2560 0.0 11.6 22.63641678 73.64979809
2550 WELD 2,816.4 2550 0.0 11.3 22.63665170 73.65003589
2580 WELD 2,850.7 2580 0.0 11.2 22.63592760 73.64884132
2570 WELD 2,839.3 2570 0.0 11.4 22.63617076 73.64935767
2460 WELD 2,715.9 2460 0.0 10.9 22.63827656 73.64975073
2430 WELD 2,682.0 2430 0.0 11.5 22.63850798 73.64774157
2420 WELD 2,668.8 2420 0.0 13.2 22.63859962 73.64709411
2450 WELD 2,704.9 2450 0.0 11.0 22.63835528 73.64917677
2440 WELD 2,693.4 2440 0.0 11.5 22.63842986 73.64853495
2400 WELD 2,651.6 2400 0.0 6.9 22.63882346 73.64644037
11000006 WT CHANGE 2,651.6 2400 0.0 0.0 22.63899148 73.64711351 17.50 70000 0.72
2410 WELD 2,658.5 2410 0.0 10.2 22.63870916 73.64671080
11000007 WT CHANGE 2,658.3 2400 0.0 0.3 22.63882119 73.64644572 15.90 70000 0.72
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 11 of 73Criteria:
2860 WELD 3,184.1 2860 0.0 10.7 22.63237940 73.64627955
2850 WELD 3,170.7 2850 0.0 13.4 22.63257074 73.64634331
2880 WELD 3,206.3 2880 0.0 11.6 22.63197452 73.64611487
2870 WELD 3,194.8 2870 0.0 11.6 22.63216496 73.64620231
2820 WELD 3,135.2 2820 0.0 11.2 22.63318366 73.64667564
2810 WELD 3,123.8 2810 0.0 11.4 22.63338167 73.64674934
2840 WELD 3,159.9 2840 0.0 10.8 22.63278692 73.64642759
2830 WELD 3,146.4 2830 0.0 13.5 22.63298236 73.64650501
2930 WELD 3,259.4 2930 0.0 12.3 22.63173101 73.64561644
11000008 WT CHANGE 3,259.4 2930 0.0 0.0 22.63177279 73.64493164 17.50 70000 0.72
2950 WELD 3,284.3 2950 0.0 12.1 22.63140855 73.64566995
2940 WELD 3,271.7 2940 0.0 12.6 22.63161100 73.64603140
2900 WELD 3,229.2 2900 0.0 10.7 22.63178250 73.64516390
2890 WELD 3,217.9 2890 0.0 11.3 22.63180021 73.64555623
2920 WELD 3,251.4 2920 0.0 8.0 22.63177322 73.64492460
2910 WELD 3,239.9 2910 0.0 11.5 22.63177164 73.64482050
2800 WELD 3,112.5 2800 0.0 11.4 22.63357412 73.64670745
2690 WELD 2,979.6 2690 0.0 13.9 22.63468918 73.64715583
2680 WELD 2,968.1 2680 0.0 11.5 22.63480580 73.64655293
2710 WELD 3,004.9 2710 0.0 11.6 22.63428936 73.64728137
2700 WELD 2,993.5 2700 0.0 11.5 22.63450668 73.64729094
2770 WELD 3,077.6 2770 0.0 11.3 22.63376961 73.64457684
2760 WELD 3,063.4 2760 0.0 14.2 22.63376837 73.64494326
2790 WELD 3,100.9 2790 0.0 11.5 22.63368363 73.64598514
2780 WELD 3,088.9 2780 0.0 12.0 22.63377986 73.64522232
2730 WELD 3,028.1 2730 0.0 11.5 22.63390687 73.64652752
2720 WELD 3,016.5 2720 0.0 11.6 22.63408834 73.64719333
2750 WELD 3,051.1 2750 0.0 12.3 22.63378407 73.64535247
2740 WELD 3,039.7 2740 0.0 11.5 22.63381490 73.64583478
2960 WELD 3,296.4 2960 0.0 12.0 22.63132685 73.64489968
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 12 of 73Criteria:
3160 WELD 3,527.8 3160 0.0 11.9 22.63091911 73.63979826
3150 WELD 3,515.8 3150 0.0 12.0 22.63118187 73.63893962
3180 WELD 3,551.9 3180 0.0 13.0 22.63044133 73.64142054
3170 WELD 3,539.7 3170 0.0 12.1 22.63067118 73.64063551
3130 WELD 3,492.5 3130 0.0 11.7 22.63149549 73.63783154
3120 WELD 3,480.2 3120 0.0 12.3 22.63164031 73.63800369
3140 WELD 3,504.2 3140 0.0 11.7 22.63146675 73.63806593
11000010 WT CHANGE 3,504.1 3140 0.0 0.1 22.63149424 73.63784174 17.50 70000 0.72
3240 WELD 3,626.5 3240 0.0 11.9 22.62934647 73.64590940
3230 WELD 3,614.4 3230 0.0 12.1 22.62949514 73.64523865
3200 WELD 3,577.9 3200 0.0 13.5 22.63001906 73.64301207
3190 WELD 3,564.8 3190 0.0 13.1 22.63022580 73.64220064
3220 WELD 3,602.4 3220 0.0 12.0 22.62964807 73.64460639
3210 WELD 3,591.4 3210 0.0 11.0 22.62982736 73.64380927
11000009 WT CHANGE 3,480.2 3120 0.0 0.0 22.63174824 73.63784768 23.80 70000 0.72
3010 WELD 3,359.1 3010 0.0 12.1 22.63132226 73.64214337
3000 WELD 3,346.5 3000 0.0 12.7 22.63128837 73.64264775
3030 WELD 3,383.3 3030 0.0 12.0 22.63139333 73.64114389
3020 WELD 3,371.2 3020 0.0 12.1 22.63135711 73.64164221
2970 WELD 3,308.4 2970 0.0 11.4 22.63127942 73.64419944
2990 WELD 3,333.1 2990 0.0 13.3 22.63126199 73.64312776
2980 WELD 3,319.9 2980 0.0 13.2 22.63125917 73.64356636
3090 WELD 3,456.7 3090 0.0 11.8 22.63183786 73.63764625
3080 WELD 3,444.9 3080 0.0 11.8 22.63172204 73.63830374
3110 WELD 3,471.0 3110 0.0 9.2 22.63175273 73.63784119
3100 WELD 3,468.5 3100 0.0 2.5 22.63194925 73.63702187
3050 WELD 3,407.3 3050 0.0 12.2 22.63149000 73.64008738
3040 WELD 3,395.2 3040 0.0 12.1 22.63143789 73.64062379
3070 WELD 3,431.8 3070 0.0 13.1 22.63162994 73.63893073
3060 WELD 3,419.5 3060 0.0 12.3 22.63155368 73.63952299
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 13 of 73Criteria:
3490 WELD 3,932.7 3490 0.0 12.4 22.62616768 73.65153985
3480 WELD 3,920.9 3480 0.0 11.8 22.62614897 73.65149359
3510 WELD 3,955.8 3510 0.0 12.2 22.62633227 73.65278177
3500 WELD 3,945.1 3500 0.0 10.7 22.62624013 73.65209310
3450 WELD 3,883.3 3450 0.0 13.3 22.62645485 73.65292788
3440 WELD 3,869.7 3440 0.0 13.7 22.62668574 73.65358385
3470 WELD 3,909.1 3470 0.0 11.8 22.62615110 73.65160786
3460 WELD 3,896.6 3460 0.0 12.5 22.62626224 73.65218046
3530 WELD 3,981.7 3530 0.0 12.6 22.62642124 73.65423096
3520 WELD 3,968.0 3520 0.0 13.7 22.62639579 73.65347909
3540 WELD 3,994.2 3540 0.0 11.9 22.62615311 73.65398670
3430 WELD 3,858.2 3430 0.0 11.5 22.62695836 73.65410716
3320 WELD 3,723.2 3320 0.0 11.5 22.62841266 73.65071151
3310 WELD 3,711.2 3310 0.0 12.1 22.62851064 73.65018739
3340 WELD 3,746.9 3340 0.0 12.8 22.62822606 73.65173447
3330 WELD 3,734.7 3330 0.0 12.2 22.62831785 73.65124186
3280 WELD 3,675.6 3280 0.0 12.6 22.62883113 73.64846985
3270 WELD 3,663.4 3270 0.0 12.2 22.62895063 73.64782294
3300 WELD 3,699.6 3300 0.0 11.6 22.62861202 73.64966418
3290 WELD 3,688.3 3290 0.0 11.3 22.62871912 73.64906691
3400 WELD 3,821.7 3400 0.0 12.4 22.62764484 73.65438933
3390 WELD 3,808.5 3390 0.0 13.2 22.62779979 73.65414132
3420 WELD 3,846.6 3420 0.0 11.6 22.62721408 73.65434616
3410 WELD 3,834.1 3410 0.0 12.4 22.62745948 73.65451671
3360 WELD 3,771.8 3360 0.0 11.6 22.62805028 73.65276665
3350 WELD 3,759.8 3350 0.0 12.1 22.62813687 73.65224494
3380 WELD 3,795.1 3380 0.0 13.4 22.62788194 73.65369785
3370 WELD 3,783.5 3370 0.0 11.7 22.62796543 73.65324556
3260 WELD 3,650.5 3260 0.0 12.9 22.62907528 73.64719740
3250 WELD 3,638.4 3250 0.0 12.1 22.62920657 73.64656596
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 14 of 73Criteria:
3570 WELD 4,022.0 3570 0.0 12.6 22.62534827 73.65257915
3560 WELD 4,018.3 3560 0.0 3.6 22.62561724 73.65322096
11000011 WT CHANGE 4,048.4 3590 0.0 0.0 22.62520402 73.65238374 23.80 70000 0.72
3580 WELD 4,034.6 3580 0.0 13.8 22.62520654 73.65239567
3550 WELD 4,006.2 3550 0.0 12.2 22.62588664 73.65366416
3800 WELD 4,294.1 3800 0.0 12.0 22.62391630 73.65266676
3790 WELD 4,281.4 3790 0.0 12.8 22.62387401 73.65250779
3820 WELD 4,319.2 3820 0.0 12.6 22.62406055 73.65333975
3810 WELD 4,306.1 3810 0.0 13.1 22.62398738 73.65297947
3760 WELD 4,245.0 3760 0.0 12.0 22.62388052 73.65273011
3750 WELD 4,233.2 3750 0.0 11.8 22.62392462 73.65299353
3780 WELD 4,269.1 3780 0.0 12.3 22.62384751 73.65243586
3770 WELD 4,257.0 3770 0.0 12.1 22.62384722 73.65250592
3740 WELD 4,221.5 3740 0.0 11.7 22.62390188 73.65293855
3630 WELD 4,097.7 3630 0.0 11.7 22.62430280 73.65177161
3620 WELD 4,085.6 3620 0.0 12.1 22.62455485 73.65217071
3650 WELD 4,121.0 3650 0.0 11.3 22.62382894 73.65108595
3640 WELD 4,109.4 3640 0.0 11.5 22.62405753 73.65135554
3600 WELD 4,060.8 3600 0.0 12.4 22.62498297 73.65235213
3590 WELD 4,048.4 3590 0.0 12.4 22.62507816 73.65178748
11000012 WT CHANGE 4,085.6 3620 0.0 0.1 22.62479949 73.65249898 17.50 70000 0.72
3610 WELD 4,073.2 3610 0.0 12.4 22.62480584 73.65250751
3710 WELD 4,186.4 3710 0.0 11.6 22.62380274 73.65252117
3700 WELD 4,174.6 3700 0.0 11.8 22.62376407 73.65225345
3730 WELD 4,209.6 3730 0.0 11.9 22.62386475 73.65277349
3720 WELD 4,198.0 3720 0.0 11.6 22.62384745 73.65272992
3670 WELD 4,143.7 3670 0.0 10.6 22.62391061 73.65162895
3660 WELD 4,132.3 3660 0.0 11.4 22.62387199 73.65138256
3690 WELD 4,164.0 3690 0.0 10.6 22.62381400 73.65170943
3680 WELD 4,154.2 3680 0.0 9.8 22.62378763 73.65106010
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 15 of 73Criteria:
3880 WELD 4,392.7 3880 0.0 12.6 22.62500136 73.65819920
3870 WELD 4,379.6 3870 0.0 13.1 22.62481129 73.65727359
3900 WELD 4,417.9 3900 0.0 11.9 22.62528896 73.65994131
3890 WELD 4,405.3 3890 0.0 12.6 22.62524979 73.65927042
3840 WELD 4,343.8 3840 0.0 12.4 22.62430941 73.65454992
3830 WELD 4,331.8 3830 0.0 12.0 22.62417738 73.65389824
3860 WELD 4,368.2 3860 0.0 11.4 22.62462615 73.65629441
3850 WELD 4,356.2 3850 0.0 12.0 22.62445550 73.65528859
3910 WELD 4,429.9 3910 0.0 12.0 22.62528360 73.66049131
4090 WELD 4,649.6 4090 0.0 13.1 22.62289947 73.65935306
4080 WELD 4,638.0 4080 0.0 11.5 22.62266010 73.65836995
4110 WELD 4,675.0 4110 0.0 12.2 22.62337750 73.66098083
4100 WELD 4,662.7 4100 0.0 12.3 22.62309696 73.66004140
11000013 WT CHANGE 4,638.0 4080 0.0 0.0 22.62303726 73.65926169 23.80 70000 0.72
3970 WELD 4,501.6 3970 0.0 12.4 22.62388423 73.65854865
3960 WELD 4,489.9 3960 0.0 11.7 22.62413505 73.65921092
3990 WELD 4,526.1 3990 0.0 12.0 22.62350430 73.65735422
3980 WELD 4,514.0 3980 0.0 12.1 22.62366141 73.65789333
3930 WELD 4,454.2 3930 0.0 13.2 22.62512378 73.66118245
3920 WELD 4,441.9 3920 0.0 12.3 22.62522368 73.66088624
3950 WELD 4,479.0 3950 0.0 10.9 22.62442452 73.65993804
3940 WELD 4,467.4 3940 0.0 11.6 22.62477875 73.66079596
4050 WELD 4,601.4 4050 0.0 11.4 22.62376556 73.66030281
4040 WELD 4,588.2 4040 0.0 13.2 22.62410086 73.66067472
4070 WELD 4,625.0 4070 0.0 13.0 22.62304169 73.65927219
4060 WELD 4,612.8 4060 0.0 12.2 22.62338527 73.65977071
4010 WELD 4,550.8 4010 0.0 12.3 22.62361921 73.65784473
4000 WELD 4,538.1 4000 0.0 12.7 22.62342203 73.65702870
4030 WELD 4,575.8 4030 0.0 12.4 22.62399758 73.65986403
4020 WELD 4,563.1 4020 0.0 12.7 22.62382506 73.65890283
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 16 of 73Criteria:
4130 WELD 4,699.5 4130 0.0 12.3 22.62347447 73.66227112
4120 WELD 4,687.2 4120 0.0 12.3 22.62341232 73.66160779
11000014 WT CHANGE 4,724.2 4150 0.0 0.0 22.62352431 73.66290198 17.50 70000 0.72
4140 WELD 4,711.8 4140 0.0 12.4 22.62352340 73.66289101
4200 WELD 4,787.6 4200 0.0 13.1 22.62276770 73.66379876
4190 WELD 4,775.6 4190 0.0 12.0 22.62322216 73.66441752
4220 WELD 4,815.3 4220 0.0 9.7 22.62246334 73.66301701
4210 WELD 4,800.7 4210 0.0 14.6 22.62256916 73.66332675
4160 WELD 4,735.7 4160 0.0 12.1 22.62373736 73.66428918
4150 WELD 4,724.2 4150 0.0 11.5 22.62357340 73.66349652
4180 WELD 4,761.8 4180 0.0 13.8 22.62373446 73.66519588
4170 WELD 4,747.9 4170 0.0 13.9 22.62382419 73.66490893
4400 WELD 5,034.3 4400 0.0 14.1 22.61749864 73.64873284
4390 WELD 5,021.7 4390 0.0 12.5 22.61762656 73.64961612
4280 WELD 4,886.1 4280 0.0 12.6 22.62078791 73.65979382
4270 WELD 4,873.4 4270 0.0 12.7 22.62119662 73.66070590
4300 WELD 4,911.5 4300 0.0 12.7 22.62002716 73.65794158
4290 WELD 4,898.8 4290 0.0 12.8 22.62039814 73.65886604
4240 WELD 4,838.5 4240 0.0 11.2 22.62178856 73.66207427
4230 WELD 4,825.0 4230 0.0 13.5 22.62196167 73.66202293
4260 WELD 4,860.7 4260 0.0 12.7 22.62157054 73.66149222
4250 WELD 4,849.7 4250 0.0 11.0 22.62183951 73.66213667
4360 WELD 4,985.3 4360 0.0 11.6 22.61819836 73.65247185
4350 WELD 4,972.4 4350 0.0 13.0 22.61845113 73.65342437
4380 WELD 5,009.7 4380 0.0 12.1 22.61778523 73.65057159
4370 WELD 4,997.0 4370 0.0 12.7 22.61797217 73.65146781
4320 WELD 4,936.1 4320 0.0 9.6 22.61933200 73.65605727
4310 WELD 4,924.3 4310 0.0 11.8 22.61967157 73.65699749
4340 WELD 4,959.9 4340 0.0 12.4 22.61876628 73.65449074
4330 WELD 4,945.7 4330 0.0 14.3 22.61902328 73.65518739
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 17 of 73Criteria:
4600 WELD 5,271.9 4600 0.0 11.8 22.61607462 73.65476843
4590 WELD 5,259.8 4590 0.0 12.1 22.61638512 73.65564980
4620 WELD 5,296.9 4620 0.0 12.0 22.61551208 73.65309601
4610 WELD 5,283.7 4610 0.0 13.2 22.61578434 73.65391652
4560 WELD 5,223.3 4560 0.0 12.0 22.61737757 73.65826191
4550 WELD 5,211.2 4550 0.0 12.0 22.61773909 73.65913791
4580 WELD 5,247.3 4580 0.0 12.5 22.61670256 73.65652364
4570 WELD 5,235.2 4570 0.0 12.1 22.61703199 73.65738953
4680 WELD 5,368.2 4680 0.0 9.3 22.61407873 73.64833485
4670 WELD 5,357.5 4670 0.0 10.7 22.61428767 73.64904124
4690 WELD 5,377.5 4690 0.0 11.3 22.61388775 73.64770423
4640 WELD 5,320.9 4640 0.0 12.2 22.61498316 73.65138812
4630 WELD 5,308.9 4630 0.0 12.0 22.61523166 73.65221239
4660 WELD 5,345.7 4660 0.0 11.8 22.61451236 73.64983994
4650 WELD 5,333.0 4650 0.0 12.6 22.61474193 73.65063837
4440 WELD 5,077.0 4440 0.0 12.2 22.61768319 73.65290162
11000015 WT CHANGE 5,077.0 4440 0.0 0.0 22.61763107 73.65184648 23.80 70000 0.72
4460 WELD 5,101.5 4460 0.0 12.2 22.61770268 73.65420374
4450 WELD 5,089.3 4450 0.0 12.2 22.61762375 73.65318495
4410 WELD 5,048.3 4410 0.0 12.5 22.61753410 73.64967467
4430 WELD 5,073.6 4430 0.0 3.5 22.61763092 73.65184344
4420 WELD 5,060.9 4420 0.0 12.7 22.61759576 73.65079797
4520 WELD 5,174.5 4520 0.0 12.2 22.61832524 73.65996408
4510 WELD 5,162.4 4510 0.0 12.1 22.61820520 73.65906748
4540 WELD 5,199.2 4540 0.0 12.1 22.61812446 73.66004002
4530 WELD 5,186.7 4530 0.0 12.4 22.61851912 73.66093697
4480 WELD 5,126.0 4480 0.0 12.3 22.61790244 73.65622507
4470 WELD 5,113.7 4470 0.0 12.3 22.61780126 73.65522133
4500 WELD 5,150.5 4500 0.0 11.8 22.61809760 73.65814510
4490 WELD 5,138.3 4490 0.0 12.2 22.61798923 73.65718427
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 18 of 73Criteria:
4770 WELD 5,472.3 4770 0.0 13.6 22.61231195 73.64569711
4760 WELD 5,460.2 4760 0.0 12.1 22.61251284 73.64571644
4790 WELD 5,498.0 4790 0.0 12.2 22.61191589 73.64606896
4780 WELD 5,485.9 4780 0.0 12.1 22.61211268 73.64572605
4730 WELD 5,423.8 4730 0.0 12.1 22.61311290 73.64613838
4720 WELD 5,412.2 4720 0.0 11.6 22.61331200 73.64639996
4750 WELD 5,448.0 4750 0.0 12.2 22.61271384 73.64578321
4740 WELD 5,435.9 4740 0.0 12.1 22.61291508 73.64593651
4850 WELD 5,569.5 4850 0.0 10.9 22.61128080 73.65021563
4840 WELD 5,557.3 4840 0.0 12.2 22.61137165 73.64953041
4870 WELD 5,590.5 4870 0.0 10.8 22.61109465 73.65143446
4860 WELD 5,580.4 4860 0.0 10.2 22.61119568 73.65089932
4810 WELD 5,522.0 4810 0.0 12.2 22.61167872 73.64750805
4800 WELD 5,510.2 4800 0.0 11.8 22.61179433 73.64679141
4830 WELD 5,545.2 4830 0.0 12.1 22.61146777 73.64890340
4820 WELD 5,534.2 4820 0.0 11.0 22.61157029 73.64819688
4710 WELD 5,400.5 4710 0.0 11.7 22.61350864 73.64686589
4700 WELD 5,388.8 4700 0.0 11.7 22.61370693 73.64728978
4930 WELD 5,657.0 4930 0.0 11.0 22.61036336 73.65189518
4920 WELD 5,646.4 4920 0.0 10.6 22.61053637 73.65263123
4950 WELD 5,680.1 4950 0.0 11.9 22.61009791 73.65062105
4940 WELD 5,667.9 4940 0.0 12.1 22.61025038 73.65131361
4890 WELD 5,611.1 4890 0.0 11.0 22.61089196 73.65241254
4880 WELD 5,601.4 4880 0.0 9.7 22.61098693 73.65189022
4910 WELD 5,634.6 4910 0.0 11.8 22.61070482 73.65338149
4900 WELD 5,622.1 4900 0.0 12.4 22.61079575 73.65286387
4970 WELD 5,702.1 4970 0.0 12.3 22.61006141 73.65012669
4960 WELD 5,692.0 4960 0.0 10.1 22.61005830 73.65022021
4980 WELD 5,714.4 4980 0.0 10.3 22.61005437 73.65009266
11000016 WT CHANGE 5,714.4 4980 0.0 0.0 22.61005921 73.65011606 17.50 70000 0.72
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 19 of 73Criteria:
5090 WELD 5,846.0 5090 0.0 12.1 22.61006641 73.65647781
5080 WELD 5,834.1 5080 0.0 11.9 22.61009918 73.65579058
5110 WELD 5,870.0 5110 0.0 11.9 22.61001198 73.65780978
5100 WELD 5,858.0 5100 0.0 12.0 22.61003668 73.65714283
5050 WELD 5,797.8 5050 0.0 11.8 22.61020721 73.65364302
5040 WELD 5,786.3 5040 0.0 11.5 22.61024664 73.65289319
5070 WELD 5,822.0 5070 0.0 12.1 22.61013522 73.65507631
5060 WELD 5,809.6 5060 0.0 12.4 22.61017273 73.65436869
5170 WELD 5,942.1 5170 0.0 11.7 22.60984915 73.66143178
5160 WELD 5,930.7 5160 0.0 11.4 22.60987992 73.66087600
5190 WELD 5,965.7 5190 0.0 12.1 22.60976152 73.66241550
5180 WELD 5,953.8 5180 0.0 11.9 22.60980414 73.66191952
5130 WELD 5,894.8 5130 0.0 12.0 22.60996038 73.65907524
5120 WELD 5,882.0 5120 0.0 12.9 22.60999065 73.65846437
5150 WELD 5,918.7 5150 0.0 12.0 22.60991301 73.66031817
5140 WELD 5,906.8 5140 0.0 11.9 22.60993788 73.65972372
5030 WELD 5,774.5 5030 0.0 11.8 22.61023509 73.65204509
5000 WELD 5,737.6 5000 0.0 12.4 22.61008517 73.65032744
4990 WELD 5,724.7 4990 0.0 13.0 22.61007190 73.65011562
5020 WELD 5,762.8 5020 0.0 11.7 22.61018195 73.65122525
5010 WELD 5,750.0 5010 0.0 12.8 22.61013161 73.65067278
5200 WELD 5,977.8 5200 0.0 12.1 22.60972023 73.66290941
5260 WELD 6,051.3 5260 0.0 12.0 22.60892117 73.66428150
5250 WELD 6,039.1 5250 0.0 12.2 22.60914160 73.66431221
5280 WELD 6,075.2 5280 0.0 12.9 22.60841467 73.66352208
5270 WELD 6,063.3 5270 0.0 11.9 22.60867917 73.66417366
5220 WELD 6,001.8 5220 0.0 11.9 22.60961756 73.66383759
5210 WELD 5,989.9 5210 0.0 11.9 22.60966878 73.66337769
5240 WELD 6,026.9 5240 0.0 12.2 22.60936010 73.66430402
5230 WELD 6,013.7 5230 0.0 13.2 22.60955249 73.66425090
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 20 of 73Criteria:
5430 WELD 6,257.5 5430 0.0 12.6 22.60815269 73.66686253
5420 WELD 6,244.5 5420 0.0 13.0 22.60847841 73.66724471
5450 WELD 6,282.7 5450 0.0 12.2 22.60744911 73.66584969
5440 WELD 6,270.1 5440 0.0 12.6 22.60779731 73.66636935
5390 WELD 6,207.7 5390 0.0 11.9 22.60894953 73.66706853
5380 WELD 6,197.2 5380 0.0 10.6 22.60879805 73.66630616
5410 WELD 6,232.3 5410 0.0 12.2 22.60879028 73.66754022
5400 WELD 6,219.6 5400 0.0 12.7 22.60906733 73.66773724
5510 WELD 6,354.9 5510 0.0 11.0 22.60562952 73.66164057
5500 WELD 6,344.4 5500 0.0 10.4 22.60587274 73.66229706
5530 WELD 6,378.1 5530 0.0 12.6 22.60517293 73.66038689
5520 WELD 6,365.9 5520 0.0 12.3 22.60540631 73.66103847
5470 WELD 6,307.6 5470 0.0 12.5 22.60676714 73.66449474
5460 WELD 6,294.8 5460 0.0 12.7 22.60710034 73.66516103
5490 WELD 6,333.0 5490 0.0 11.4 22.60614851 73.66304579
5480 WELD 6,320.1 5480 0.0 13.0 22.60643813 73.66377068
5370 WELD 6,185.3 5370 0.0 11.9 22.60864360 73.66554399
5340 WELD 6,148.4 5340 0.0 13.1 22.60813743 73.66334227
5330 WELD 6,136.6 5330 0.0 11.8 22.60798914 73.66272635
5360 WELD 6,173.5 5360 0.0 11.8 22.60847538 73.66479696
5350 WELD 6,161.5 5350 0.0 11.9 22.60828903 73.66400479
5300 WELD 6,099.0 5300 0.0 13.5 22.60791942 73.66219027
5290 WELD 6,088.1 5290 0.0 10.9 22.60816501 73.66287984
5320 WELD 6,124.3 5320 0.0 12.3 22.60786167 73.66219028
5310 WELD 6,112.5 5310 0.0 11.8 22.60771473 73.66162514
5580 WELD 6,440.1 5580 0.0 12.6 22.60430247 73.65714248
5550 WELD 6,402.9 5550 0.0 12.3 22.60475726 73.65899605
5540 WELD 6,390.7 5540 0.0 12.2 22.60494072 73.65966516
5570 WELD 6,427.3 5570 0.0 12.8 22.60444557 73.65775363
5560 WELD 6,415.2 5560 0.0 12.1 22.60459389 73.65836614
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 21 of 73Criteria:
5880 WELD 6,812.6 5880 0.0 11.9 22.60144310 73.65364207
5870 WELD 6,799.3 5870 0.0 13.3 22.60138879 73.65282046
5760 WELD 6,661.9 5760 0.0 12.2 22.60309339 73.65719086
5750 WELD 6,649.6 5750 0.0 12.2 22.60304553 73.65631556
5780 WELD 6,686.2 5780 0.0 12.4 22.60254684 73.65585809
5770 WELD 6,674.0 5770 0.0 12.2 22.60281621 73.65653666
5720 WELD 6,613.1 5720 0.0 12.1 22.60289183 73.65370980
5710 WELD 6,600.8 5710 0.0 12.3 22.60284452 73.65287963
5740 WELD 6,637.5 5740 0.0 12.1 22.60299262 73.65542447
5730 WELD 6,625.2 5730 0.0 12.3 22.60294179 73.65456338
5840 WELD 6,761.1 5840 0.0 13.0 22.60124253 73.65081898
5830 WELD 6,749.3 5830 0.0 11.8 22.60140758 73.65167285
5860 WELD 6,786.8 5860 0.0 12.4 22.60133319 73.65206725
5850 WELD 6,774.1 5850 0.0 12.7 22.60127892 73.65138738
5800 WELD 6,711.7 5800 0.0 13.4 22.60204286 73.65431516
5790 WELD 6,698.6 5790 0.0 13.1 22.60228890 73.65511440
5820 WELD 6,737.1 5820 0.0 12.2 22.60159616 73.65250715
5810 WELD 6,725.0 5810 0.0 12.0 22.60181187 73.65342644
5700 WELD 6,588.5 5700 0.0 12.3 22.60279814 73.65211789
5590 WELD 6,452.7 5590 0.0 12.7 22.60416308 73.65649399
5610 WELD 6,477.9 5610 0.0 11.9 22.60401032 73.65557887
5600 WELD 6,465.4 5600 0.0 12.5 22.60407826 73.65601362
5670 WELD 6,550.8 5670 0.0 13.2 22.60273163 73.65096898
5660 WELD 6,538.4 5660 0.0 12.4 22.60289268 73.65180162
5690 WELD 6,576.2 5690 0.0 12.3 22.60275819 73.65138865
5680 WELD 6,564.0 5680 0.0 12.3 22.60271288 73.65066150
5630 WELD 6,501.6 5630 0.0 11.8 22.60350925 73.65414985
5620 WELD 6,489.8 5620 0.0 11.8 22.60374910 73.65487050
5650 WELD 6,525.9 5650 0.0 12.5 22.60307741 73.65263753
5640 WELD 6,513.4 5640 0.0 12.5 22.60328597 73.65340671
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 22 of 73Criteria:
6090 WELD 7,071.6 6090 0.0 14.1 22.59973297 73.65344683
6080 WELD 7,058.4 6080 0.0 13.2 22.59969950 73.65306121
6110 WELD 7,097.9 6110 0.0 12.1 22.59971586 73.65542389
6100 WELD 7,085.7 6100 0.0 12.2 22.59970562 73.65438155
6050 WELD 7,023.6 6050 0.0 12.0 22.59962924 73.65258732
6040 WELD 7,011.3 6040 0.0 12.3 22.59967388 73.65306600
6070 WELD 7,048.0 6070 0.0 10.4 22.59964600 73.65262772
6060 WELD 7,035.6 6060 0.0 12.4 22.59960199 73.65225480
6170 WELD 7,170.6 6170 0.0 12.2 22.60004996 73.66098074
6160 WELD 7,158.5 6160 0.0 12.1 22.59998043 73.66009025
6180 WELD 7,182.8 6180 0.0 12.2 22.60013117 73.66188383
6130 WELD 7,121.8 6130 0.0 12.2 22.59980715 73.65730707
6120 WELD 7,109.9 6120 0.0 11.9 22.59976049 73.65637276
6150 WELD 7,146.6 6150 0.0 11.9 22.59991030 73.65914186
6140 WELD 7,134.0 6140 0.0 12.6 22.59985463 73.65821921
6030 WELD 6,998.0 6030 0.0 13.3 22.59974333 73.65356283
5920 WELD 6,861.2 5920 0.0 12.3 22.60170584 73.65722990
5910 WELD 6,848.8 5910 0.0 12.4 22.60163644 73.65630217
5940 WELD 6,887.3 5940 0.0 12.7 22.60172542 73.65887670
5930 WELD 6,873.5 5930 0.0 13.8 22.60172772 73.65809425
5900 WELD 6,836.5 5900 0.0 12.4 22.60157350 73.65542330
5890 WELD 6,824.5 5890 0.0 11.9 22.60151463 73.65456372
6000 WELD 6,960.5 6000 0.0 12.6 22.60026330 73.65608074
5990 WELD 6,948.4 5990 0.0 12.1 22.60046375 73.65686808
6020 WELD 6,986.4 6020 0.0 11.6 22.59990586 73.65443987
6010 WELD 6,973.1 6010 0.0 13.2 22.60007206 73.65526206
5960 WELD 6,911.3 5960 0.0 13.0 22.60131092 73.65887868
5950 WELD 6,899.9 5950 0.0 11.4 22.60157521 73.65919374
5980 WELD 6,936.8 5980 0.0 11.6 22.60074170 73.65762884
5970 WELD 6,924.3 5970 0.0 12.5 22.60103750 73.65832795
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 23 of 73Criteria:
6190 WELD 7,195.1 6190 0.0 12.2 22.60022222 73.66278896
6410 WELD 7,458.1 6410 0.0 11.4 22.59997206 73.67099847
6400 WELD 7,444.5 6400 0.0 13.7 22.59996273 73.67105442
6430 WELD 7,480.9 6430 0.0 12.2 22.60009044 73.67122661
6420 WELD 7,469.6 6420 0.0 11.3 22.60002453 73.67106252
11000017 WT CHANGE 7,424.0 6380 0.0 0.0 22.60025451 73.67175847 15.90 70000 0.72
6370 WELD 7,411.4 6370 0.0 12.6 22.60025862 73.67176875
6390 WELD 7,430.8 6390 0.0 13.7 22.60002514 73.67112456
6380 WELD 7,424.0 6380 0.0 6.7 22.60008208 73.67132679
6450 WELD 7,504.5 6450 0.0 11.1 22.60033017 73.67185658
6440 WELD 7,493.1 6440 0.0 11.4 22.60018693 73.67148394
6470 WELD 7,527.7 6470 0.0 12.0 22.60070508 73.67293964
6460 WELD 7,515.6 6460 0.0 12.1 22.60048940 73.67229875
6360 WELD 7,400.1 6360 0.0 11.3 22.60051596 73.67239428
6250 WELD 7,268.3 6250 0.0 12.1 22.60091713 73.66803618
6240 WELD 7,255.7 6240 0.0 12.6 22.60076481 73.66710678
6270 WELD 7,291.8 6270 0.0 12.1 22.60120392 73.66974456
6260 WELD 7,280.4 6260 0.0 11.3 22.60106570 73.66891705
6210 WELD 7,219.1 6210 0.0 12.3 22.60042663 73.66457294
6200 WELD 7,207.2 6200 0.0 11.8 22.60032098 73.66368612
6230 WELD 7,242.5 6230 0.0 13.2 22.60065716 73.66631482
6220 WELD 7,231.4 6220 0.0 11.1 22.60053430 73.66543060
6330 WELD 7,363.2 6330 0.0 11.7 22.60136069 73.67300892
6320 WELD 7,351.6 6320 0.0 11.5 22.60152421 73.67288313
6350 WELD 7,387.3 6350 0.0 12.7 22.60088666 73.67285614
6340 WELD 7,374.8 6340 0.0 12.5 22.60118926 73.67311083
6290 WELD 7,315.7 6290 0.0 11.6 22.60147878 73.67132335
6280 WELD 7,303.8 6280 0.0 11.9 22.60133200 73.67051439
6310 WELD 7,339.9 6310 0.0 11.7 22.60166210 73.67267251
6300 WELD 7,327.3 6300 0.0 12.6 22.60164133 73.67213167
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 24 of 73Criteria:
6490 WELD 7,550.0 6490 0.0 11.5 22.60041938 73.67325474
6480 WELD 7,539.7 6480 0.0 10.3 22.60071468 73.67347191
6510 WELD 7,572.8 6510 0.0 11.1 22.59984237 73.67278553
6500 WELD 7,561.5 6500 0.0 11.2 22.60014201 73.67303730
6520 WELD 7,583.9 6520 0.0 11.3 22.59953455 73.67249190
6750 WELD 7,849.2 6750 0.0 11.0 22.59259813 73.65737289
6740 WELD 7,837.3 6740 0.0 11.8 22.59281042 73.65818261
6770 WELD 7,871.7 6770 0.0 11.4 22.59219614 73.65574249
6760 WELD 7,860.2 6760 0.0 11.5 22.59238890 73.65652998
6710 WELD 7,801.1 6710 0.0 13.5 22.59352559 73.66073260
6700 WELD 7,789.5 6700 0.0 11.6 22.59377581 73.66151976
6730 WELD 7,825.9 6730 0.0 11.5 22.59303149 73.65897948
6720 WELD 7,814.6 6720 0.0 11.3 22.59328531 73.65992751
6690 WELD 7,778.1 6690 0.0 11.4 22.59403662 73.66230007
6580 WELD 7,652.0 6580 0.0 11.6 22.59755722 73.67006977
6570 WELD 7,640.7 6570 0.0 11.3 22.59789670 73.67054899
6600 WELD 7,675.1 6600 0.0 11.3 22.59685522 73.66891784
6590 WELD 7,663.6 6590 0.0 11.5 22.59720961 73.66952135
6540 WELD 7,606.6 6540 0.0 11.4 22.59889978 73.67181631
6530 WELD 7,595.2 6530 0.0 11.5 22.59921982 73.67216402
6560 WELD 7,629.4 6560 0.0 11.4 22.59823462 73.67100575
6550 WELD 7,618.1 6550 0.0 11.3 22.59857221 73.67143722
6660 WELD 7,744.4 6660 0.0 11.2 22.59486741 73.66460413
6650 WELD 7,733.0 6650 0.0 11.4 22.59517147 73.66538671
6680 WELD 7,766.8 6680 0.0 11.3 22.59430455 73.66306801
6670 WELD 7,755.6 6670 0.0 11.2 22.59457971 73.66383204
6620 WELD 7,697.7 6620 0.0 11.3 22.59616044 73.66760698
6610 WELD 7,686.4 6610 0.0 11.3 22.59650286 73.66826188
6640 WELD 7,721.4 6640 0.0 11.6 22.59549669 73.66621416
6630 WELD 7,709.0 6630 0.0 12.3 22.59582441 73.66692998
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 25 of 73Criteria:
6830 WELD 7,941.2 6830 0.0 11.9 22.59116135 73.65070617
6820 WELD 7,929.1 6820 0.0 12.0 22.59131394 73.65153363
6850 WELD 7,964.3 6850 0.0 11.4 22.59086514 73.64892610
6840 WELD 7,953.0 6840 0.0 11.3 22.59101031 73.64981211
6790 WELD 7,894.9 6790 0.0 11.8 22.59181932 73.65408510
6780 WELD 7,883.1 6780 0.0 11.8 22.59200271 73.65490956
6810 WELD 7,918.0 6810 0.0 11.2 22.59147286 73.65236190
6800 WELD 7,906.7 6800 0.0 11.3 22.59164210 73.65322377
7070 WELD 8,221.8 7070 0.0 13.5 22.58852102 73.63248604
7040 WELD 8,181.9 7040 0.0 12.6 22.58880092 73.63438586
7030 WELD 8,170.6 7030 0.0 11.3 22.58888978 73.63500201
7060 WELD 8,208.1 7060 0.0 13.7 22.58863821 73.63305841
7050 WELD 8,194.5 7050 0.0 13.7 22.58871724 73.63375383
7020 WELD 8,159.5 7020 0.0 11.1 22.58897786 73.63563492
6910 WELD 8,033.3 6910 0.0 11.7 22.59010760 73.64379323
6900 WELD 8,022.1 6900 0.0 11.2 22.59022382 73.64462475
6930 WELD 8,056.6 6930 0.0 11.4 22.58988794 73.64215060
6920 WELD 8,045.0 6920 0.0 11.6 22.58999845 73.64298120
6870 WELD 7,987.6 6870 0.0 11.3 22.59059510 73.64723224
6860 WELD 7,975.7 6860 0.0 11.9 22.59072746 73.64808210
6890 WELD 8,010.7 6890 0.0 11.4 22.59034453 73.64549691
6880 WELD 7,998.9 6880 0.0 11.8 22.59046599 73.64634137
6990 WELD 8,126.0 6990 0.0 10.7 22.58924294 73.63771815
6980 WELD 8,114.3 6980 0.0 11.7 22.58933602 73.63843832
7010 WELD 8,148.5 7010 0.0 11.0 22.58906274 73.63634180
7000 WELD 8,136.7 7000 0.0 11.7 22.58915213 73.63699421
6960 WELD 8,090.8 6960 0.0 12.1 22.58954309 73.63991799
6940 WELD 8,068.0 6940 0.0 11.5 22.58976767 73.64139169
6950 WELD 8,079.5 6950 0.0 11.3 22.58965328 73.64065393
6970 WELD 8,103.0 6970 0.0 11.4 22.58943811 73.63919839
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 26 of 73Criteria:
7370 WELD 8,583.3 7370 0.0 11.7 22.58553379 73.61947507
7360 WELD 8,571.9 7360 0.0 11.4 22.58559637 73.61991198
7350 WELD 8,560.4 7350 0.0 11.4 22.58566350 73.62036131
7240 WELD 8,422.5 7240 0.0 11.3 22.58668335 73.62498514
7230 WELD 8,411.2 7230 0.0 11.3 22.58678270 73.62537152
7260 WELD 8,446.4 7260 0.0 12.4 22.58648231 73.62422240
7250 WELD 8,433.8 7250 0.0 12.5 22.58658716 73.62458728
7200 WELD 8,377.4 7200 0.0 11.4 22.58709324 73.62654900
7190 WELD 8,365.9 7190 0.0 11.5 22.58719907 73.62693772
7220 WELD 8,400.1 7220 0.0 11.1 22.58688322 73.62576682
7210 WELD 8,388.8 7210 0.0 11.3 22.58698687 73.62615755
7320 WELD 8,523.1 7320 0.0 11.4 22.58589827 73.62173638
7310 WELD 8,509.4 7310 0.0 13.8 22.58598785 73.62219980
7340 WELD 8,548.3 7340 0.0 12.1 22.58573590 73.62085572
7330 WELD 8,534.5 7330 0.0 13.8 22.58581536 73.62126117
7280 WELD 8,470.2 7280 0.0 11.3 22.58626916 73.62343903
7270 WELD 8,458.8 7270 0.0 11.4 22.58637766 73.62381909
7300 WELD 8,495.6 7300 0.0 13.8 22.58607561 73.62268305
7290 WELD 8,481.5 7290 0.0 14.0 22.58616876 73.62306870
7080 WELD 8,235.3 7080 0.0 11.5 22.58840735 73.63191355
7100 WELD 8,258.2 7100 0.0 14.0 22.58818833 73.63088597
7090 WELD 8,246.8 7090 0.0 11.5 22.58829817 73.63134497
7160 WELD 8,332.2 7160 0.0 11.2 22.58752282 73.62811148
7150 WELD 8,321.1 7150 0.0 11.1 22.58763432 73.62852388
7180 WELD 8,354.7 7180 0.0 11.2 22.58730636 73.62732889
7170 WELD 8,343.4 7170 0.0 11.3 22.58741480 73.62771979
7120 WELD 8,285.0 7120 0.0 13.2 22.58796677 73.62989332
7110 WELD 8,272.3 7110 0.0 12.7 22.58807802 73.63043845
7140 WELD 8,309.4 7140 0.0 11.8 22.58774366 73.62892877
7130 WELD 8,298.2 7130 0.0 11.2 22.58785561 73.62941382
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 27 of 73Criteria:
7410 WELD 8,627.8 7410 0.0 11.4 22.58535493 73.61760614
7400 WELD 8,617.6 7400 0.0 10.2 22.58539132 73.61808101
7430 WELD 8,651.0 7430 0.0 11.3 22.58532408 73.61661293
7420 WELD 8,639.2 7420 0.0 11.7 22.58533650 73.61713187
7390 WELD 8,606.3 7390 0.0 11.3 22.58543283 73.61855074
7380 WELD 8,595.0 7380 0.0 11.4 22.58547462 73.61903533
7490 WELD 8,719.7 7490 0.0 12.0 22.58533028 73.61344752
7480 WELD 8,708.5 7480 0.0 11.3 22.58531805 73.61397578
7510 WELD 8,742.9 7510 0.0 11.2 22.58536633 73.61236939
7500 WELD 8,731.8 7500 0.0 11.1 22.58534284 73.61292587
7450 WELD 8,673.4 7450 0.0 11.7 22.58530637 73.61557268
7440 WELD 8,662.3 7440 0.0 11.1 22.58531733 73.61607992
7470 WELD 8,697.1 7470 0.0 11.3 22.58530569 73.61452946
7460 WELD 8,685.1 7460 0.0 12.0 22.58529821 73.61507164
7570 WELD 8,812.2 7570 0.0 11.1 22.58558451 73.60910618
7560 WELD 8,800.9 7560 0.0 11.2 22.58553417 73.60965081
7590 WELD 8,834.8 7590 0.0 11.3 22.58569902 73.60801458
7580 WELD 8,823.3 7580 0.0 11.5 22.58564066 73.60855822
7530 WELD 8,766.3 7530 0.0 11.8 22.58540645 73.61133340
7520 WELD 8,754.1 7520 0.0 12.3 22.58538433 73.61185310
7550 WELD 8,789.7 7550 0.0 11.2 22.58548029 73.61021436
7540 WELD 8,778.2 7540 0.0 11.6 22.58544625 73.61076078
7650 WELD 8,905.3 7650 0.0 11.4 22.58616202 73.60460207
7640 WELD 8,894.1 7640 0.0 11.1 22.58608772 73.60513888
7670 WELD 8,928.5 7670 0.0 12.0 22.58631647 73.60353094
7660 WELD 8,916.7 7660 0.0 11.8 22.58623764 73.60406978
7610 WELD 8,857.3 7610 0.0 13.9 22.58583262 73.60690696
7600 WELD 8,846.1 7600 0.0 11.3 22.58576896 73.60745180
7630 WELD 8,882.9 7630 0.0 11.2 22.58600804 73.60570077
7620 WELD 8,871.2 7620 0.0 11.7 22.58589661 73.60636721
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 28 of 73Criteria:
7900 WELD 9,205.5 7900 0.0 11.8 22.59146877 73.58952684
7890 WELD 9,194.1 7890 0.0 11.4 22.59119538 73.59007509
7920 WELD 9,229.1 7920 0.0 11.3 22.59204363 73.58841016
7910 WELD 9,217.3 7910 0.0 11.8 22.59174795 73.58897467
7860 WELD 9,159.4 7860 0.0 12.2 22.59038313 73.59177264
7850 WELD 9,148.1 7850 0.0 11.2 22.59013015 73.59233815
7880 WELD 9,182.8 7880 0.0 11.3 22.59092974 73.59062179
7870 WELD 9,171.6 7870 0.0 11.2 22.59063943 73.59121672
7970 WELD 9,287.5 7970 0.0 12.0 22.59358913 73.58565609
7940 WELD 9,251.6 7940 0.0 13.7 22.59263443 73.58730880
7930 WELD 9,240.5 7930 0.0 11.2 22.59234462 73.58784722
7960 WELD 9,276.5 7960 0.0 11.0 22.59329387 73.58616641
7950 WELD 9,265.3 7950 0.0 11.2 22.59292211 73.58678013
7740 WELD 9,010.2 7740 0.0 12.3 22.58733911 73.59931289
7730 WELD 8,999.8 7730 0.0 10.3 22.58712218 73.59998716
7760 WELD 9,033.7 7760 0.0 10.6 22.58773344 73.59813303
7750 WELD 9,022.5 7750 0.0 11.3 22.58750605 73.59876828
7700 WELD 8,963.6 7700 0.0 11.3 22.58669332 73.60174729
7690 WELD 8,952.3 7690 0.0 11.3 22.58655569 73.60234736
7720 WELD 8,986.8 7720 0.0 13.0 22.58696436 73.60059354
7710 WELD 8,974.9 7710 0.0 11.9 22.58682739 73.60116918
7820 WELD 9,111.3 7820 0.0 13.8 22.58925253 73.59430949
7810 WELD 9,097.6 7810 0.0 13.8 22.58894942 73.59500828
7840 WELD 9,136.9 7840 0.0 11.3 22.58987119 73.59292843
7830 WELD 9,125.2 7830 0.0 11.7 22.58955842 73.59361939
7780 WELD 9,055.9 7780 0.0 14.1 22.58813232 73.59699964
7770 WELD 9,044.3 7770 0.0 11.6 22.58793765 73.59754841
7800 WELD 9,083.7 7800 0.0 13.9 22.58865775 73.59570011
7790 WELD 9,070.0 7790 0.0 13.7 22.58835959 73.59640641
7680 WELD 8,940.5 7680 0.0 11.8 22.58642103 73.60295545
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 29 of 73Criteria:
8070 WELD 9,402.7 8070 0.0 11.4 22.59672080 73.58077350
8060 WELD 9,391.2 8060 0.0 11.5 22.59646115 73.58111579
8090 WELD 9,425.3 8090 0.0 11.2 22.59716626 73.58021099
8080 WELD 9,414.1 8080 0.0 11.2 22.59695848 73.58046941
8030 WELD 9,356.8 8030 0.0 11.6 22.59551206 73.58251573
8020 WELD 9,345.6 8020 0.0 11.2 22.59519355 73.58301676
8050 WELD 9,379.7 8050 0.0 11.5 22.59616335 73.58153411
8040 WELD 9,368.4 8040 0.0 11.3 22.59583357 73.58201826
8150 WELD 9,492.6 8150 0.0 11.4 22.59784037 73.57943003
8140 WELD 9,481.5 8140 0.0 11.0 22.59783565 73.57943021
8170 WELD 9,515.0 8170 0.0 11.3 22.59778759 73.57950970
8160 WELD 9,504.0 8160 0.0 11.1 22.59782510 73.57945488
8110 WELD 9,448.0 8110 0.0 11.1 22.59752101 73.57977937
8100 WELD 9,436.6 8100 0.0 11.5 22.59734967 73.57998625
8130 WELD 9,470.6 8130 0.0 10.9 22.59776204 73.57950445
8120 WELD 9,459.1 8120 0.0 11.5 22.59766725 73.57961140
8010 WELD 9,334.4 8010 0.0 11.2 22.59488120 73.58351939
7980 WELD 9,299.5 7980 0.0 11.4 22.59388057 73.58515282
8000 WELD 9,323.3 8000 0.0 11.1 22.59452798 73.58407947
7990 WELD 9,310.9 7990 0.0 12.4 22.59421377 73.58460142
8230 WELD 9,585.3 8230 0.0 11.5 22.59709145 73.58038909
8220 WELD 9,573.6 8220 0.0 11.7 22.59727077 73.58015919
8250 WELD 9,608.0 8250 0.0 11.0 22.59616987 73.58135403
8240 WELD 9,596.8 8240 0.0 11.1 22.59662719 73.58087234
8190 WELD 9,537.6 8190 0.0 11.3 22.59765178 73.57968352
8180 WELD 9,526.4 8180 0.0 11.3 22.59773129 73.57958188
8210 WELD 9,561.1 8210 0.0 12.5 22.59742336 73.57996301
8200 WELD 9,548.9 8200 0.0 12.2 22.59755110 73.57980821
8270 WELD 9,630.2 8270 0.0 11.3 22.59527338 73.58230280
8260 WELD 9,619.0 8260 0.0 11.2 22.59572002 73.58182775
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 30 of 73Criteria:
8560 WELD 9,953.9 8560 0.0 11.1 22.58194503 73.59808758
8550 WELD 9,942.6 8550 0.0 11.3 22.58236561 73.59757068
8570 WELD 9,965.0 8570 0.0 11.8 22.58153485 73.59858895
8520 WELD 9,909.8 8520 0.0 10.3 22.58360179 73.59607904
8510 WELD 9,899.0 8510 0.0 10.8 22.58404219 73.59554028
8540 WELD 9,931.2 8540 0.0 11.4 22.58278129 73.59706537
8530 WELD 9,920.1 8530 0.0 11.0 22.58318036 73.59659012
8400 WELD 9,775.1 8400 0.0 11.3 22.58922450 73.58930010
8390 WELD 9,764.0 8390 0.0 11.2 22.58971958 73.58869033
8420 WELD 9,798.0 8420 0.0 11.7 22.58826009 73.59049280
8410 WELD 9,786.4 8410 0.0 11.6 22.58874315 73.58989118
8360 WELD 9,730.0 8360 0.0 11.2 22.59112411 73.58698422
8350 WELD 9,718.9 8350 0.0 11.2 22.59158502 73.58644028
8380 WELD 9,752.4 8380 0.0 11.6 22.59018479 73.58811890
8370 WELD 9,741.3 8370 0.0 11.1 22.59065552 73.58754613
8480 WELD 9,865.5 8480 0.0 11.0 22.58538263 73.59392564
8470 WELD 9,854.4 8470 0.0 11.0 22.58584183 73.59337516
8500 WELD 9,887.7 8500 0.0 11.2 22.58448803 73.59499921
8490 WELD 9,876.5 8490 0.0 11.3 22.58493259 73.59446483
8440 WELD 9,820.9 8440 0.0 11.0 22.58725795 73.59169768
8430 WELD 9,809.7 8430 0.0 11.2 22.58775897 73.59110523
8460 WELD 9,843.3 8460 0.0 11.1 22.58631778 73.59280598
8450 WELD 9,831.8 8450 0.0 11.5 22.58678168 73.59225971
8340 WELD 9,707.9 8340 0.0 11.0 22.59206057 73.58588202
8310 WELD 9,674.5 8310 0.0 11.0 22.59343792 73.58431423
8300 WELD 9,663.5 8300 0.0 11.0 22.59389599 73.58380676
8330 WELD 9,696.5 8330 0.0 11.4 22.59252228 73.58534955
8320 WELD 9,685.5 8320 0.0 11.0 22.59298119 73.58482793
8290 WELD 9,652.6 8290 0.0 11.0 22.59435418 73.58330187
8280 WELD 9,641.5 8280 0.0 11.1 22.59481566 73.58279735
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 31 of 73Criteria:
8730 WELD 10,148.5 8730 0.0 11.0 22.57886635 73.59750936
8720 WELD 10,137.3 8720 0.0 11.2 22.57879207 73.59803625
8750 WELD 10,170.6 8750 0.0 10.9 22.57905015 73.59640072
8740 WELD 10,159.5 8740 0.0 11.2 22.57895839 73.59695060
8690 WELD 10,104.2 8690 0.0 11.3 22.57855992 73.59969174
8680 WELD 10,093.1 8680 0.0 11.1 22.57845802 73.60035371
8710 WELD 10,126.6 8710 0.0 10.7 22.57870957 73.59859032
8700 WELD 10,115.5 8700 0.0 11.1 22.57863117 73.59914692
8810 WELD 10,239.4 8810 0.0 12.2 22.57972251 73.59295510
8800 WELD 10,229.0 8800 0.0 10.3 22.57955900 73.59363473
8830 WELD 10,263.1 8830 0.0 11.4 22.57998286 73.59181591
8820 WELD 10,251.5 8820 0.0 11.6 22.57982844 73.59243408
8770 WELD 10,192.6 8770 0.0 11.4 22.57924276 73.59530050
8760 WELD 10,181.5 8760 0.0 11.1 22.57914699 73.59584459
8790 WELD 10,215.2 8790 0.0 13.8 22.57944688 73.59419420
8780 WELD 10,204.0 8780 0.0 11.2 22.57933687 73.59475976
8670 WELD 10,079.4 8670 0.0 13.7 22.57867042 73.60035517
8580 WELD 9,976.8 8580 0.0 11.4 22.58113974 73.59905822
8640 WELD 10,045.3 8640 0.0 11.6 22.57934828 73.60027330
8630 WELD 10,033.9 8630 0.0 11.4 22.57959735 73.60018848
8660 WELD 10,068.1 8660 0.0 11.3 22.57888342 73.60035358
8650 WELD 10,056.9 8650 0.0 11.2 22.57911175 73.60032565
8600 WELD 9,999.4 8600 0.0 11.1 22.58043993 73.59972495
8590 WELD 9,988.1 8590 0.0 11.2 22.58073938 73.59952493
8620 WELD 10,022.6 8620 0.0 11.3 22.57987972 73.60004558
8610 WELD 10,010.4 8610 0.0 12.2 22.58015340 73.59989828
8850 WELD 10,285.8 8850 0.0 11.1 22.58030329 73.59061493
8840 WELD 10,274.5 8840 0.0 11.3 22.58014213 73.59121123
8870 WELD 10,308.4 8870 0.0 11.1 22.58066446 73.58940656
8860 WELD 10,296.8 8860 0.0 11.5 22.58047753 73.59001089
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 32 of 73Criteria:
9060 WELD 10,534.9 9060 0.0 13.3 22.58620321 73.57699573
9050 WELD 10,523.4 9050 0.0 11.5 22.58580761 73.57768870
9080 WELD 10,559.6 9080 0.0 11.1 22.58696252 73.57569396
9070 WELD 10,548.2 9070 0.0 11.4 22.58654612 73.57638817
9020 WELD 10,486.6 9020 0.0 12.2 22.58482028 73.57957393
9010 WELD 10,475.3 9010 0.0 11.3 22.58451475 73.58019099
9040 WELD 10,510.3 9040 0.0 13.1 22.58547849 73.57830385
9030 WELD 10,498.8 9030 0.0 11.4 22.58513054 73.57895844
9140 WELD 10,626.3 9140 0.0 11.8 22.58910264 73.57224315
9130 WELD 10,615.3 9130 0.0 11.0 22.58874427 73.57279888
9160 WELD 10,649.3 9160 0.0 11.3 22.58986585 73.57110075
9150 WELD 10,638.1 9150 0.0 11.2 22.58946703 73.57168770
9100 WELD 10,582.0 9100 0.0 11.1 22.58766320 73.57452278
9090 WELD 10,570.7 9090 0.0 11.3 22.58731415 73.57509811
9120 WELD 10,604.4 9120 0.0 10.9 22.58837783 73.57337217
9110 WELD 10,593.1 9110 0.0 11.3 22.58802270 73.57394049
9000 WELD 10,464.0 9000 0.0 11.3 22.58421169 73.58081888
8890 WELD 10,331.1 8890 0.0 13.5 22.58109411 73.58815018
8880 WELD 10,319.5 8880 0.0 11.6 22.58088094 73.58876843
8910 WELD 10,358.0 8910 0.0 13.5 22.58163258 73.58675988
8900 WELD 10,344.5 8900 0.0 13.5 22.58133441 73.58750180
8970 WELD 10,426.6 8970 0.0 12.1 22.58326623 73.58284094
8960 WELD 10,415.3 8960 0.0 11.3 22.58300031 73.58345809
8990 WELD 10,452.5 8990 0.0 11.5 22.58384238 73.58156297
8980 WELD 10,438.7 8980 0.0 13.8 22.58354005 73.58222100
8930 WELD 10,381.9 8930 0.0 11.3 22.58225668 73.58527609
8920 WELD 10,371.5 8920 0.0 10.4 22.58194079 73.58601819
8950 WELD 10,404.2 8950 0.0 11.2 22.58274466 73.58406875
8940 WELD 10,393.1 8940 0.0 11.0 22.58248569 73.58469373
9170 WELD 10,660.6 9170 0.0 11.7 22.59024760 73.57054146
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 33 of 73Criteria:
9400 WELD 10,926.0 9400 0.0 11.1 22.59569615 73.56405802
9390 WELD 10,914.8 9390 0.0 11.1 22.59564770 73.56409472
9420 WELD 10,948.7 9420 0.0 11.2 22.59576953 73.56400071
9410 WELD 10,937.0 9410 0.0 11.6 22.59573576 73.56402691
9360 WELD 10,878.9 9360 0.0 11.4 22.59541063 73.56428115
9350 WELD 10,868.0 9350 0.0 10.9 22.59532552 73.56435965
9380 WELD 10,903.4 9380 0.0 11.4 22.59556974 73.56413831
9370 WELD 10,890.3 9370 0.0 13.1 22.59549227 73.56420444
9470 WELD 11,005.6 9470 0.0 11.5 22.59549018 73.56431895
9440 WELD 10,971.2 9440 0.0 11.5 22.59578882 73.56400465
9430 WELD 10,959.9 9430 0.0 11.4 22.59578923 73.56399558
9460 WELD 10,994.2 9460 0.0 11.5 22.59571024 73.56410327
9450 WELD 10,982.7 9450 0.0 11.4 22.59577618 73.56402771
9340 WELD 10,856.9 9340 0.0 11.1 22.59523348 73.56444295
9230 WELD 10,729.1 9230 0.0 12.0 22.59263741 73.56727972
9220 WELD 10,717.3 9220 0.0 11.8 22.59224084 73.56779589
9250 WELD 10,753.1 9250 0.0 11.4 22.59348339 73.56624484
9240 WELD 10,741.1 9240 0.0 12.0 22.59305631 73.56675963
9190 WELD 10,683.6 9190 0.0 11.2 22.59104588 73.56941374
9180 WELD 10,672.3 9180 0.0 11.3 22.59063790 73.56998254
9210 WELD 10,706.2 9210 0.0 11.1 22.59183665 73.56832983
9200 WELD 10,694.8 9200 0.0 11.4 22.59144213 73.56886532
9310 WELD 10,823.2 9310 0.0 11.4 22.59483040 73.56479556
9300 WELD 10,809.4 9300 0.0 13.8 22.59467953 73.56493198
9330 WELD 10,845.6 9330 0.0 11.3 22.59513118 73.56454074
9320 WELD 10,834.6 9320 0.0 11.0 22.59501009 73.56465332
9270 WELD 10,775.6 9270 0.0 10.7 22.59424043 73.56537974
9260 WELD 10,764.5 9260 0.0 11.0 22.59388574 73.56578114
9290 WELD 10,797.3 9290 0.0 12.1 22.59454200 73.56506918
9280 WELD 10,786.3 9280 0.0 11.0 22.59440257 73.56521401
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 34 of 73Criteria:
9480 WELD 11,017.1 9480 0.0 11.9 22.59524346 73.56456004
9500 WELD 11,040.5 9500 0.0 11.4 22.59461630 73.56517082
9490 WELD 11,029.0 9490 0.0 11.5 22.59495523 73.56484002
9730 WELD 11,301.3 9730 0.0 14.2 22.58116828 73.57754191
9720 WELD 11,290.3 9720 0.0 10.9 22.58168893 73.57705870
9750 WELD 11,326.7 9750 0.0 11.4 22.58005305 73.57858644
9740 WELD 11,315.5 9740 0.0 11.2 22.58066075 73.57800979
9690 WELD 11,256.9 9690 0.0 11.2 22.58333599 73.57552668
9680 WELD 11,245.5 9680 0.0 11.5 22.58389833 73.57500879
9710 WELD 11,279.4 9710 0.0 11.0 22.58222293 73.57656495
9700 WELD 11,268.2 9700 0.0 11.2 22.58277085 73.57605411
9770 WELD 11,351.6 9770 0.0 11.4 22.57909211 73.57943189
9760 WELD 11,338.1 9760 0.0 13.5 22.57956489 73.57902285
9670 WELD 11,234.2 9670 0.0 11.2 22.58447411 73.57447570
9560 WELD 11,108.4 9560 0.0 11.4 22.59130187 73.56815895
9550 WELD 11,097.0 9550 0.0 11.4 22.59191507 73.56759990
9580 WELD 11,130.8 9580 0.0 11.2 22.59005268 73.56930104
9570 WELD 11,119.8 9570 0.0 11.0 22.59068564 73.56872494
9520 WELD 11,063.0 9520 0.0 11.0 22.59368263 73.56602279
9510 WELD 11,051.9 9510 0.0 11.1 22.59426711 73.56550810
9540 WELD 11,085.5 9540 0.0 11.4 22.59252879 73.56704438
9530 WELD 11,074.0 9530 0.0 11.6 22.59310439 73.56653248
9640 WELD 11,197.6 9640 0.0 14.0 22.58638653 73.57266797
9630 WELD 11,186.3 9630 0.0 11.3 22.58696378 73.57213938
9660 WELD 11,222.9 9660 0.0 11.3 22.58505781 73.57393271
9650 WELD 11,211.7 9650 0.0 11.2 22.58578090 73.57322971
9600 WELD 11,153.3 9600 0.0 11.0 22.58881619 73.57042707
9590 WELD 11,142.1 9590 0.0 11.2 22.58943943 73.56985792
9620 WELD 11,175.7 9620 0.0 10.6 22.58758521 73.57156049
9610 WELD 11,164.4 9610 0.0 11.4 22.58819427 73.57099765
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 35 of 73Criteria:
10060 WELD 11,696.5 10060 0.0 10.9 22.57659483 73.57314674
10050 WELD 11,685.3 10050 0.0 11.2 22.57643375 73.57366210
10070 WELD 11,707.4 10070 0.0 11.2 22.57676795 73.57261819
10020 WELD 11,650.0 10020 0.0 13.8 22.57587235 73.57541558
10010 WELD 11,636.2 10010 0.0 13.9 22.57568171 73.57603157
10040 WELD 11,674.3 10040 0.0 11.0 22.57628978 73.57415330
10030 WELD 11,663.9 10030 0.0 10.5 22.57607583 73.57478692
10000 WELD 11,622.5 10000 0.0 13.7 22.57553632 73.57655617
9890 WELD 11,491.2 9890 0.0 11.4 22.57625495 73.57945235
9880 WELD 11,480.3 9880 0.0 10.9 22.57637387 73.57962427
9910 WELD 11,514.3 9910 0.0 13.9 22.57602630 73.57908405
9900 WELD 11,502.6 9900 0.0 11.7 22.57613623 73.57927893
9850 WELD 11,449.2 9850 0.0 11.3 22.57679044 73.58002918
9840 WELD 11,438.0 9840 0.0 11.1 22.57696987 73.58011658
9870 WELD 11,469.4 9870 0.0 10.8 22.57649186 73.57976544
9860 WELD 11,460.5 9860 0.0 8.9 22.57663690 73.57990536
9970 WELD 11,588.7 9970 0.0 11.5 22.57544029 73.57770089
9960 WELD 11,577.8 9960 0.0 10.9 22.57552703 73.57792133
9990 WELD 11,611.1 9990 0.0 11.3 22.57541063 73.57705451
9980 WELD 11,600.1 9980 0.0 11.0 22.57537854 73.57744637
9930 WELD 11,539.2 9930 0.0 13.9 22.57581921 73.57862997
9920 WELD 11,528.2 9920 0.0 11.0 22.57592180 73.57887602
9950 WELD 11,566.8 9950 0.0 11.0 22.57562651 73.57816756
9940 WELD 11,553.1 9940 0.0 13.7 22.57572562 73.57841898
9810 WELD 11,398.9 9810 0.0 13.9 22.57765939 73.58025786
9800 WELD 11,385.4 9800 0.0 13.4 22.57788191 73.58027310
9830 WELD 11,426.6 9830 0.0 11.4 22.57718208 73.58019486
9820 WELD 11,412.7 9820 0.0 13.9 22.57741627 73.58023715
9790 WELD 11,374.3 9790 0.0 11.2 22.57812616 73.58025491
9780 WELD 11,363.0 9780 0.0 11.3 22.57856342 73.57990226
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 36 of 73Criteria:
10080 WELD 11,718.6 10080 0.0 11.2 22.57693595 73.57210329
10140 WELD 11,786.8 10140 0.0 11.1 22.57827842 73.56872758
10130 WELD 11,775.1 10130 0.0 11.7 22.57803465 73.56929103
10160 WELD 11,810.1 10160 0.0 11.5 22.57891510 73.56748550
10150 WELD 11,797.9 10150 0.0 12.1 22.57859851 73.56809494
10100 WELD 11,741.6 10100 0.0 11.3 22.57731446 73.57102984
10090 WELD 11,729.7 10090 0.0 11.9 22.57712114 73.57156835
10120 WELD 11,764.1 10120 0.0 10.9 22.57778691 73.56986693
10110 WELD 11,753.0 10110 0.0 11.2 22.57754812 73.57044290
10350 WELD 12,020.3 10350 0.0 11.0 22.58569050 73.55635168
10340 WELD 12,009.0 10340 0.0 11.3 22.58548849 73.55669562
10370 WELD 12,042.3 10370 0.0 13.1 22.58653249 73.55524163
10360 WELD 12,031.2 10360 0.0 11.1 22.58611643 73.55578666
10330 WELD 12,002.8 10330 0.0 6.2 22.58507305 73.55726274
10220 WELD 11,879.2 10220 0.0 11.2 22.58101679 73.56371021
10210 WELD 11,868.2 10210 0.0 10.9 22.58068363 73.56430573
10240 WELD 11,902.3 10240 0.0 11.4 22.58168830 73.56253600
10230 WELD 11,890.3 10230 0.0 12.0 22.58134681 73.56312745
10180 WELD 11,832.8 10180 0.0 12.3 22.57960993 73.56620593
10170 WELD 11,821.6 10170 0.0 11.2 22.57926868 73.56683051
10200 WELD 11,857.0 10200 0.0 11.2 22.58032799 73.56493740
10190 WELD 11,845.1 10190 0.0 11.9 22.57994398 73.56559791
10300 WELD 11,968.8 10300 0.0 11.3 22.58387383 73.55901070
10290 WELD 11,957.5 10290 0.0 11.3 22.58351660 73.55956776
10320 WELD 11,991.6 10320 0.0 11.2 22.58464566 73.55784594
10310 WELD 11,980.1 10310 0.0 11.6 22.58425706 73.55842734
10260 WELD 11,924.3 10260 0.0 11.2 22.58242806 73.56131075
10250 WELD 11,913.7 10250 0.0 10.6 22.58206602 73.56190890
10280 WELD 11,946.9 10280 0.0 10.6 22.58313453 73.56016334
10270 WELD 11,935.5 10270 0.0 11.4 22.58276374 73.56075197
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 37 of 73Criteria:
10570 WELD 12,271.5 10570 0.0 10.8 22.59465394 73.54642581
10560 WELD 12,260.2 10560 0.0 11.2 22.59430714 73.54670151
10590 WELD 12,293.9 10590 0.0 11.1 22.59520257 73.54595925
10580 WELD 12,282.3 10580 0.0 11.6 22.59494000 73.54618356
10520 WELD 12,212.8 10520 0.0 11.0 22.59313840 73.54771820
10510 WELD 12,201.8 10510 0.0 10.9 22.59284341 73.54798281
10540 WELD 12,236.1 10540 0.0 11.0 22.59370913 73.54720853
10530 WELD 12,223.8 10530 0.0 12.4 22.59342189 73.54746366
10650 WELD 12,362.5 10650 0.0 11.2 22.59625345 73.54515040
10640 WELD 12,351.2 10640 0.0 11.3 22.59617153 73.54519235
10670 WELD 12,386.0 10670 0.0 11.1 22.59637713 73.54506899
10660 WELD 12,373.7 10660 0.0 12.4 22.59631855 73.54510788
10610 WELD 12,316.2 10610 0.0 11.0 22.59570404 73.54555290
10600 WELD 12,305.0 10600 0.0 11.2 22.59546954 73.54574416
10630 WELD 12,338.7 10630 0.0 12.5 22.59608766 73.54524811
10620 WELD 12,327.2 10620 0.0 11.5 22.59593658 73.54536602
10500 WELD 12,190.6 10500 0.0 11.2 22.59252130 73.54827198
10550 WELD 12,247.1 10550 0.0 13.1 22.59402675 73.54694586
10390 WELD 12,066.9 10390 0.0 11.1 22.58747485 73.55406033
10380 WELD 12,055.4 10380 0.0 11.5 22.58695763 73.55469239
10410 WELD 12,089.5 10410 0.0 11.2 22.58836768 73.55296444
10400 WELD 12,078.0 10400 0.0 11.4 22.58792746 73.55350214
10470 WELD 12,156.8 10470 0.0 11.1 22.59110538 73.54980806
10460 WELD 12,145.4 10460 0.0 11.4 22.59065440 73.55031442
10490 WELD 12,179.1 10490 0.0 11.6 22.59204890 73.54877933
10480 WELD 12,167.9 10480 0.0 11.1 22.59158161 73.54928687
10430 WELD 12,111.9 10430 0.0 10.8 22.58927647 73.55188777
10420 WELD 12,100.7 10420 0.0 11.2 22.58882536 73.55241937
10450 WELD 12,134.5 10450 0.0 10.9 22.59016774 73.55085631
10440 WELD 12,122.7 10440 0.0 11.8 22.58972961 73.55136312
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 38 of 73Criteria:
10740 WELD 12,466.6 10740 0.0 11.9 22.59660929 73.54498144
10730 WELD 12,455.5 10730 0.0 11.1 22.59660327 73.54495485
10760 WELD 12,490.0 10760 0.0 11.2 22.59659633 73.54501410
10750 WELD 12,478.5 10750 0.0 11.5 22.59660739 73.54498989
10700 WELD 12,419.4 10700 0.0 11.1 22.59652247 73.54498735
10690 WELD 12,408.1 10690 0.0 11.3 22.59648120 73.54501535
10720 WELD 12,442.3 10720 0.0 13.2 22.59658325 73.54495554
10710 WELD 12,430.5 10710 0.0 11.8 22.59655723 73.54496929
10820 WELD 12,559.3 10820 0.0 12.5 22.59635474 73.54526157
10810 WELD 12,546.9 10810 0.0 12.4 22.59645209 73.54517420
10840 WELD 12,583.3 10840 0.0 11.2 22.59598922 73.54558507
10830 WELD 12,571.8 10830 0.0 11.5 22.59618901 73.54541017
10780 WELD 12,512.5 10780 0.0 11.3 22.59655092 73.54506806
10770 WELD 12,501.1 10770 0.0 11.3 22.59657437 73.54504226
10800 WELD 12,535.3 10800 0.0 11.6 22.59649533 73.54512964
10790 WELD 12,523.8 10790 0.0 11.5 22.59651750 73.54510332
10680 WELD 12,397.2 10680 0.0 10.9 22.59643867 73.54504195
10900 WELD 12,656.8 10900 0.0 11.4 22.59415380 73.54710576
10890 WELD 12,645.0 10890 0.0 11.7 22.59458253 73.54673702
10920 WELD 12,679.6 10920 0.0 11.1 22.59322660 73.54784054
10910 WELD 12,668.2 10910 0.0 11.4 22.59374471 73.54743539
10860 WELD 12,605.8 10860 0.0 14.0 22.59556086 73.54593091
10850 WELD 12,594.5 10850 0.0 11.3 22.59578503 73.54575219
10880 WELD 12,631.2 10880 0.0 13.8 22.59491817 73.54647006
10870 WELD 12,619.8 10870 0.0 11.4 22.59530431 73.54613541
10970 WELD 12,735.8 10970 0.0 11.2 22.59026412 73.55018819
10940 WELD 12,702.2 10940 0.0 11.3 22.59214049 73.54869372
10930 WELD 12,690.7 10930 0.0 11.5 22.59268265 73.54826749
10960 WELD 12,724.9 10960 0.0 10.9 22.59092046 73.54966312
10950 WELD 12,713.5 10950 0.0 11.4 22.59154350 73.54916933
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 39 of 73Criteria:
11210 WELD 13,013.6 11210 0.0 11.2 22.57704646 73.56007307
11200 WELD 13,002.7 11200 0.0 10.9 22.57655711 73.56069454
11230 WELD 13,036.7 11230 0.0 14.1 22.57793310 73.55893918
11220 WELD 13,024.8 11220 0.0 11.9 22.57748020 73.55951334
11180 WELD 12,977.9 11180 0.0 12.6 22.57661669 73.56091802
11000018 WT CHANGE 12,977.9 11180 0.0 12.6 22.57710413 73.56061289 23.80 70000 0.72
11000019 WT CHANGE 13,002.7 11200 0.0 0.0 22.57596939 73.56158443 15.90 70000 0.72
11190 WELD 12,990.5 11190 0.0 12.2 22.57596358 73.56159322
11250 WELD 13,061.4 11250 0.0 11.3 22.57902027 73.55764343
11240 WELD 13,050.8 11240 0.0 10.6 22.57842999 73.55832731
11070 WELD 12,853.2 11070 0.0 11.4 22.58302995 73.55638579
11060 WELD 12,841.9 11060 0.0 11.2 22.58372405 73.55577526
11090 WELD 12,875.5 11090 0.0 11.0 22.58165634 73.55749294
11080 WELD 12,864.6 11080 0.0 10.9 22.58229373 73.55704410
11030 WELD 12,808.6 11030 0.0 11.4 22.58603820 73.55372602
11020 WELD 12,794.9 11020 0.0 13.7 22.58673979 73.55312564
11050 WELD 12,831.3 11050 0.0 10.6 22.58445665 73.55513166
11040 WELD 12,820.0 11040 0.0 11.3 22.58518570 73.55449287
11150 WELD 12,944.8 11150 0.0 10.2 22.57817670 73.55990680
11140 WELD 12,931.6 11140 0.0 13.2 22.57872086 73.55953651
11170 WELD 12,966.6 11170 0.0 11.3 22.57711213 73.56060788
11160 WELD 12,955.1 11160 0.0 11.5 22.57757264 73.56032610
11110 WELD 12,897.7 11110 0.0 11.9 22.58046655 73.55832034
11100 WELD 12,886.5 11100 0.0 11.2 22.58105774 73.55790858
11130 WELD 12,920.5 11130 0.0 11.1 22.57927308 73.55915560
11120 WELD 12,909.6 11120 0.0 10.9 22.57988116 73.55872646
11010 WELD 12,783.6 11010 0.0 11.3 22.58741998 73.55255386
10980 WELD 12,747.1 10980 0.0 11.8 22.58961977 73.55070321
11000 WELD 12,772.7 11000 0.0 11.0 22.58825342 73.55182965
10990 WELD 12,758.8 10990 0.0 13.8 22.58895731 73.55124360
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 40 of 73Criteria:
11380 WELD 13,219.5 11380 0.0 11.6 22.58622322 73.54978294
11370 WELD 13,208.2 11370 0.0 11.3 22.58566392 73.55035146
11400 WELD 13,242.6 11400 0.0 13.8 22.58737788 73.54863288
11390 WELD 13,231.1 11390 0.0 11.5 22.58678823 73.54921492
11340 WELD 13,171.6 11340 0.0 13.9 22.58375600 73.55229381
11330 WELD 13,157.6 11330 0.0 14.0 22.58322486 73.55286606
11360 WELD 13,196.8 11360 0.0 11.4 22.58511024 73.55092526
11350 WELD 13,185.5 11350 0.0 11.3 22.58442786 73.55161016
11460 WELD 13,315.3 11460 0.0 11.5 22.59086405 73.54540300
11450 WELD 13,301.9 11450 0.0 13.4 22.59031402 73.54589726
11480 WELD 13,340.1 11480 0.0 11.3 22.59203089 73.54440797
11470 WELD 13,326.7 11470 0.0 13.3 22.59150624 73.54486070
11420 WELD 13,267.9 11420 0.0 11.4 22.58864973 73.54743588
11410 WELD 13,256.4 11410 0.0 11.5 22.58794330 73.54808435
11440 WELD 13,290.5 11440 0.0 11.3 22.58977776 73.54638567
11430 WELD 13,279.3 11430 0.0 11.3 22.58921116 73.54691050
11320 WELD 13,146.1 11320 0.0 11.5 22.58274252 73.55340160
11290 WELD 13,107.6 11290 0.0 14.0 22.58092630 73.55537903
11280 WELD 13,095.6 11280 0.0 12.0 22.58041458 73.55597044
11310 WELD 13,135.4 11310 0.0 10.7 22.58211276 73.55406782
11300 WELD 13,121.6 11300 0.0 13.8 22.58146382 73.55476965
11270 WELD 13,084.0 11270 0.0 11.7 22.57993160 73.55654054
11260 WELD 13,072.7 11260 0.0 11.3 22.57945363 73.55711051
11540 WELD 13,412.3 11540 0.0 13.1 22.59544657 73.54166526
11530 WELD 13,401.2 11530 0.0 11.1 22.59493475 73.54207380
11550 WELD 13,425.4 11550 0.0 10.2 22.59596311 73.54125625
11500 WELD 13,362.9 11500 0.0 13.6 22.59317792 73.54345678
11490 WELD 13,351.4 11490 0.0 11.5 22.59266175 73.54389080
11520 WELD 13,390.0 11520 0.0 11.2 22.59431921 73.54254504
11510 WELD 13,376.5 11510 0.0 13.5 22.59371103 73.54301497
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 41 of 73Criteria:
11670 WELD 13,556.2 11670 0.0 12.5 22.59955054 73.53860862
11660 WELD 13,543.8 11660 0.0 12.3 22.59950058 73.53862653
11690 WELD 13,581.2 11690 0.0 12.1 22.59945872 73.53871430
11680 WELD 13,568.7 11680 0.0 12.5 22.59961872 73.53858118
11640 WELD 13,520.8 11640 0.0 11.0 22.59895047 73.53897782
11630 WELD 13,507.0 11630 0.0 13.8 22.59871581 73.53913980
11650 WELD 13,531.8 11650 0.0 12.0 22.59925843 73.53879386
11000022 WT CHANGE 13,531.8 11650 0.0 0.0 22.59895836 73.53897311 23.80 70000 0.72
11750 WELD 13,655.1 11750 0.0 12.6 22.59635684 73.54066509
11740 WELD 13,642.8 11740 0.0 12.3 22.59568257 73.54141087
11000023 WT CHANGE 13,679.9 11770 0.0 12.1 22.59503952 73.54154808 15.90 70000 0.72
11760 WELD 13,667.7 11760 0.0 12.2 22.59504799 73.54154231
11710 WELD 13,605.7 11710 0.0 12.4 22.59845719 73.53943385
11700 WELD 13,593.3 11700 0.0 12.3 22.59919222 73.53892064
11730 WELD 13,630.4 11730 0.0 12.4 22.59674805 73.54065052
11720 WELD 13,618.1 11720 0.0 12.3 22.59764029 73.54001128
11620 WELD 13,495.8 11620 0.0 11.2 22.59848617 73.53929664
11560 WELD 13,435.6 11560 0.0 11.2 22.59659976 73.54078152
11590 WELD 13,460.3 11590 0.0 11.3 22.59776393 73.53982749
11580 WELD 13,452.7 11580 0.0 7.6 22.59765250 73.53996522
11610 WELD 13,484.4 11610 0.0 11.4 22.59820239 73.53947822
11600 WELD 13,471.6 11600 0.0 12.8 22.59792786 73.53967183
11570 WELD 13,446.8 11570 0.0 5.8 22.59709408 73.54039013
11000020 WT CHANGE 13,446.8 11570 0.0 0.0 22.59660716 73.54077566 23.80 70000 0.72
11000021 WT CHANGE 13,452.3 11570 0.0 0.3 22.59709776 73.54038733 15.90 70000 0.72
10000003 Bend right 13,449.4 11570 1.3 4.5 22.59709497 73.54038945 0 12:00
11770 WELD 13,679.9 11770 0.0 12.1 22.59371866 73.54244712
11790 WELD 13,706.0 11790 0.0 3.4 22.59121216 73.54416873
11780 WELD 13,692.0 11780 0.0 14.1 22.59244424 73.54331650
11800 WELD 13,709.4 11800 0.0 7.2 22.58983121 73.54515332
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 42 of 73Criteria:
11970 WELD 13,898.4 11970 0.0 13.4 22.57729960 73.55335180
11960 WELD 13,886.9 11960 0.0 11.5 22.57791712 73.55295004
11990 WELD 13,923.3 11990 0.0 14.0 22.57599567 73.55422560
11980 WELD 13,911.8 11980 0.0 11.6 22.57668530 73.55375419
11930 WELD 13,852.7 11930 0.0 11.4 22.57983960 73.55170052
11920 WELD 13,841.6 11920 0.0 11.2 22.58055739 73.55122315
11950 WELD 13,875.5 11950 0.0 11.4 22.57854322 73.55254447
11940 WELD 13,864.1 11940 0.0 11.4 22.57918152 73.55213223
12050 WELD 13,998.5 12050 0.0 13.9 22.57248655 73.55653490
12040 WELD 13,984.8 12040 0.0 13.7 22.57307818 73.55614434
12070 WELD 14,024.1 12070 0.0 11.0 22.57133763 73.55727250
12060 WELD 14,012.4 12060 0.0 11.6 22.57189062 73.55693137
12010 WELD 13,949.1 12010 0.0 11.2 22.57470536 73.55510221
12000 WELD 13,937.3 12000 0.0 11.8 22.57539947 73.55461912
12030 WELD 13,971.5 12030 0.0 13.3 22.57359488 73.55582125
12020 WELD 13,960.4 12020 0.0 11.2 22.57412133 73.55549138
11910 WELD 13,829.5 11910 0.0 12.1 22.58125721 73.55076603
10000004 Bend right 13,721.3 11810 2.2 5.9 22.58945899 73.54533078 0 12:00
11810 WELD 13,716.6 11810 0.0 8.2 22.58946056 73.54532976
11820 WELD 13,724.7 11820 0.0 11.0 22.58874225 73.54579527
11000025 WT CHANGE 13,724.7 11820 0.0 0.0 22.58945485 73.54533346 15.90 70000 0.72
11000024 WT CHANGE 13,716.5 11810 0.0 0.0 22.58982587 73.54515587 23.80 70000 0.72
11880 WELD 13,792.4 11880 0.0 13.9 22.58369705 73.54911789
11870 WELD 13,781.0 11870 0.0 11.4 22.58471596 73.54839912
11900 WELD 13,818.0 11900 0.0 11.5 22.58201062 73.55026199
11890 WELD 13,806.2 11890 0.0 11.8 22.58290428 73.54964891
11840 WELD 13,747.1 11840 0.0 11.4 22.58714485 73.54680967
11830 WELD 13,735.7 11830 0.0 11.5 22.58803428 73.54623002
11860 WELD 13,767.0 11860 0.0 14.0 22.58536303 73.54799546
11850 WELD 13,758.5 11850 0.0 8.4 22.58623248 73.54741806
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 43 of 73Criteria:
12300 WELD 14,279.7 12300 0.0 11.3 22.56315924 73.56073711
12290 WELD 14,266.0 12290 0.0 13.8 22.56350264 73.56063515
12320 WELD 14,302.2 12320 0.0 11.5 22.56253679 73.56089831
12310 WELD 14,291.0 12310 0.0 11.2 22.56282302 73.56083325
12260 WELD 14,229.5 12260 0.0 11.3 22.56446519 73.56033715
12250 WELD 14,216.0 12250 0.0 13.5 22.56479031 73.56022028
12280 WELD 14,252.0 12280 0.0 14.0 22.56379559 73.56056273
12270 WELD 14,240.8 12270 0.0 11.2 22.56409177 73.56048737
12370 WELD 14,358.9 12370 0.0 11.4 22.56112530 73.56119795
12340 WELD 14,325.3 12340 0.0 11.1 22.56196738 73.56102380
12330 WELD 14,313.7 12330 0.0 11.6 22.56225435 73.56096020
12360 WELD 14,347.8 12360 0.0 11.2 22.56140499 73.56114142
12350 WELD 14,336.3 12350 0.0 11.4 22.56168082 73.56108618
12240 WELD 14,204.8 12240 0.0 11.2 22.56512324 73.56009708
12130 WELD 14,076.9 12130 0.0 11.3 22.56920095 73.55831205
12120 WELD 14,065.3 12120 0.0 11.6 22.56959263 73.55812304
12150 WELD 14,099.6 12150 0.0 12.3 22.56840791 73.55869700
12140 WELD 14,088.2 12140 0.0 11.4 22.56879716 73.55851041
12090 WELD 14,038.9 12090 0.0 5.1 22.57043444 73.55778555
12080 WELD 14,035.0 12080 0.0 3.9 22.57087182 73.55754077
12110 WELD 14,054.2 12110 0.0 11.1 22.56999750 73.55790495
12100 WELD 14,044.0 12100 0.0 10.2 22.57023606 73.55782817
12210 WELD 14,168.6 12210 0.0 11.5 22.56618528 73.55967718
12200 WELD 14,157.4 12200 0.0 11.3 22.56652754 73.55954417
12230 WELD 14,193.4 12230 0.0 11.4 22.56550439 73.55993842
12220 WELD 14,180.1 12220 0.0 13.3 22.56584537 73.55980778
12170 WELD 14,123.5 12170 0.0 11.2 22.56760940 73.55908496
12160 WELD 14,111.9 12160 0.0 11.5 22.56801890 73.55888309
12190 WELD 14,146.1 12190 0.0 11.2 22.56687682 73.55940534
12180 WELD 14,134.7 12180 0.0 11.4 22.56722557 73.55926621
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 44 of 73Criteria:
12630 WELD 14,659.5 12630 0.0 11.2 22.55499790 73.56102834
12620 WELD 14,647.6 12620 0.0 11.8 22.55511633 73.56121310
12650 WELD 14,684.4 12650 0.0 9.3 22.55482875 73.56056528
12640 WELD 14,670.7 12640 0.0 13.8 22.55489562 73.56081719
12590 WELD 14,613.6 12590 0.0 11.1 22.55559806 73.56155154
12580 WELD 14,602.5 12580 0.0 11.1 22.55578428 73.56161669
12610 WELD 14,636.0 12610 0.0 11.7 22.55525869 73.56135468
12600 WELD 14,624.7 12600 0.0 11.2 22.55542131 73.56146387
12670 WELD 14,705.7 12670 0.0 11.4 22.55481656 73.55988102
12660 WELD 14,693.7 12660 0.0 12.0 22.55482251 73.56018664
12570 WELD 14,591.9 12570 0.0 10.6 22.55598776 73.56165934
12460 WELD 14,461.0 12460 0.0 11.4 22.55869067 73.56161927
12450 WELD 14,449.9 12450 0.0 11.1 22.55895279 73.56158058
12480 WELD 14,483.7 12480 0.0 11.7 22.55816905 73.56169270
12470 WELD 14,472.4 12470 0.0 11.4 22.55843121 73.56165572
12420 WELD 14,415.9 12420 0.0 11.5 22.55976061 73.56144772
12410 WELD 14,404.3 12410 0.0 11.7 22.56003154 73.56140070
12440 WELD 14,438.7 12440 0.0 11.2 22.55921722 73.56153979
12430 WELD 14,427.4 12430 0.0 11.3 22.55948648 73.56149554
12540 WELD 14,558.2 12540 0.0 11.1 22.55661622 73.56178088
12530 WELD 14,547.2 12530 0.0 11.0 22.55683541 73.56180256
12560 WELD 14,581.0 12560 0.0 10.9 22.55620157 73.56169998
12550 WELD 14,569.3 12550 0.0 11.7 22.55640921 73.56174072
12500 WELD 14,509.2 12500 0.0 13.8 22.55764448 73.56176415
12490 WELD 14,495.4 12490 0.0 13.9 22.55790853 73.56172797
12520 WELD 14,536.2 12520 0.0 11.0 22.55709686 73.56179402
12510 WELD 14,523.0 12510 0.0 13.1 22.55736973 73.56178009
12380 WELD 14,370.3 12380 0.0 11.4 22.56085181 73.56125003
12400 WELD 14,392.9 12400 0.0 11.4 22.56030095 73.56135362
12390 WELD 14,381.7 12390 0.0 11.2 22.56057601 73.56130250
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 45 of 73Criteria:
12710 WELD 14,755.1 12710 0.0 11.1 22.55445808 73.55975432
12700 WELD 14,742.5 12700 0.0 12.6 22.55471811 73.55938414
12730 WELD 14,777.7 12730 0.0 11.8 22.55381505 73.56068369
12720 WELD 14,766.2 12720 0.0 11.5 22.55413937 73.56022715
12690 WELD 14,731.3 12690 0.0 11.2 22.55498278 73.55895840
12680 WELD 14,717.1 12680 0.0 14.2 22.55488331 73.55943518
12960 WELD 15,036.6 12960 0.0 14.1 22.55307889 73.55863607
12950 WELD 15,023.1 12950 0.0 13.5 22.55292673 73.55885251
12970 WELD 15,050.6 12970 0.0 12.5 22.55320719 73.55848869
12920 WELD 14,988.7 12920 0.0 11.5 22.55229402 73.55982380
12910 WELD 14,977.2 12910 0.0 11.5 22.55203638 73.56024304
12940 WELD 15,011.4 12940 0.0 11.7 22.55275091 73.55911817
12930 WELD 15,000.2 12930 0.0 11.2 22.55253571 73.55944661
12900 WELD 14,966.2 12900 0.0 11.0 22.55174405 73.56072494
12790 WELD 14,846.6 12790 0.0 11.1 22.55110512 73.56444363
12780 WELD 14,835.1 12780 0.0 11.5 22.55161521 73.56375265
12810 WELD 14,869.1 12810 0.0 11.5 22.55066046 73.56442025
12800 WELD 14,857.6 12800 0.0 11.4 22.55086085 73.56446517
12750 WELD 14,800.6 12750 0.0 11.3 22.55301845 73.56180909
12740 WELD 14,789.5 12740 0.0 11.1 22.55343304 73.56122201
12770 WELD 14,823.9 12770 0.0 11.2 22.55212967 73.56303725
12760 WELD 14,811.9 12760 0.0 12.0 22.55259646 73.56239423
12870 WELD 14,932.2 12870 0.0 11.5 22.55073253 73.56247180
12860 WELD 14,920.4 12860 0.0 11.8 22.55034382 73.56318057
12890 WELD 14,954.9 12890 0.0 11.3 22.55143361 73.56125029
12880 WELD 14,943.6 12880 0.0 11.2 22.55109678 73.56183128
12830 WELD 14,892.1 12830 0.0 4.9 22.55040034 73.56408568
12820 WELD 14,880.6 12820 0.0 11.5 22.55050677 73.56429168
12850 WELD 14,908.5 12850 0.0 11.9 22.55029161 73.56362502
12840 WELD 14,896.9 12840 0.0 11.5 22.55034229 73.56380445
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 46 of 73Criteria:
13240 WELD 15,359.6 13240 0.0 11.2 22.54807337 73.56120555
13230 WELD 15,349.9 13230 0.0 9.8 22.54798614 73.56171958
13250 WELD 15,370.9 13250 0.0 11.5 22.54814372 73.56076745
11000027 WT CHANGE 15,349.8 13230 0.0 0.0 22.54802765 73.56202838 15.90 70000 0.72
13130 WELD 15,235.3 13130 0.0 11.3 22.55112328 73.55847281
13120 WELD 15,224.4 13120 0.0 10.9 22.55140594 73.55806836
13150 WELD 15,260.6 13150 0.0 6.3 22.55037797 73.55952194
13140 WELD 15,246.6 13140 0.0 14.0 22.55077916 73.55895637
13090 WELD 15,190.6 13090 0.0 11.4 22.55013353 73.56043371
13080 WELD 15,179.4 13080 0.0 11.2 22.54972162 73.56126550
13110 WELD 15,213.5 13110 0.0 11.0 22.55097734 73.55882806
13100 WELD 15,202.0 13100 0.0 11.5 22.55054908 73.55962404
13200 WELD 15,312.3 13200 0.0 12.6 22.54807320 73.56272591
11000026 WT CHANGE 15,312.3 13200 0.0 12.6 22.54807320 73.56272591 25.00 70000 0.72
13220 WELD 15,337.3 13220 0.0 12.6 22.54802912 73.56203938
13210 WELD 15,324.9 13210 0.0 12.4 22.54813281 73.56226864
13170 WELD 15,278.2 13170 0.0 11.5 22.54956736 73.56062928
13160 WELD 15,266.9 13160 0.0 11.3 22.54985163 73.56030015
13190 WELD 15,300.9 13190 0.0 11.3 22.54858667 73.56200930
13180 WELD 15,289.7 13180 0.0 11.2 22.54909244 73.56129743
13070 WELD 15,168.0 13070 0.0 11.4 22.54933412 73.56209463
12980 WELD 15,063.2 12980 0.0 11.6 22.55253625 73.55937445
13040 WELD 15,133.8 13040 0.0 11.1 22.54910993 73.56329028
13030 WELD 15,121.4 13030 0.0 12.4 22.54964263 73.56274482
13060 WELD 15,156.6 13060 0.0 11.4 22.54895129 73.56294153
13050 WELD 15,144.9 13050 0.0 11.7 22.54863442 73.56372202
13000 WELD 15,086.2 13000 0.0 11.3 22.55130773 73.56087979
12990 WELD 15,074.8 12990 0.0 11.4 22.55190192 73.56016776
13020 WELD 15,109.0 13020 0.0 12.4 22.55017638 73.56217267
13010 WELD 15,097.5 13010 0.0 11.5 22.55073209 73.56154906
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 47 of 73Criteria:
13280 WELD 15,404.9 13280 0.0 11.4 22.54843924 73.55926434
13270 WELD 15,393.7 13270 0.0 11.2 22.54833927 73.55976424
13300 WELD 15,427.6 13300 0.0 11.4 22.54862685 73.55829065
13290 WELD 15,416.3 13290 0.0 11.3 22.54853210 73.55877929
13260 WELD 15,382.4 13260 0.0 11.3 22.54823517 73.56027595
13360 WELD 15,490.1 13360 0.0 10.0 22.54936710 73.55513303
13350 WELD 15,487.5 13350 0.0 2.5 22.54920098 73.55574523
13380 WELD 15,511.8 13380 0.0 11.5 22.54944350 73.55451117
13370 WELD 15,500.0 13370 0.0 11.8 22.54933501 73.55497524
13320 WELD 15,450.2 13320 0.0 12.5 22.54885134 73.55727543
13310 WELD 15,438.9 13310 0.0 11.3 22.54873905 73.55778237
13340 WELD 15,473.5 13340 0.0 14.1 22.54909014 73.55623241
13330 WELD 15,462.7 13330 0.0 10.8 22.54896084 73.55677663
13550 WELD 15,708.5 13550 0.0 11.3 22.55304463 73.54454994
13440 WELD 15,584.9 13440 0.0 11.2 22.55058436 73.55095449
13430 WELD 15,573.5 13430 0.0 11.4 22.55038877 73.55152793
13460 WELD 15,607.1 13460 0.0 11.0 22.55100818 73.54978263
13450 WELD 15,596.0 13450 0.0 11.0 22.55078230 73.55037950
13400 WELD 15,534.6 13400 0.0 13.7 22.54975855 73.55341034
13390 WELD 15,523.3 13390 0.0 11.3 22.54960497 73.55395127
13420 WELD 15,562.1 13420 0.0 11.3 22.55013263 73.55222050
13410 WELD 15,548.3 13410 0.0 13.8 22.54990872 73.55287870
13520 WELD 15,673.7 13520 0.0 12.3 22.55234427 73.54630358
13510 WELD 15,662.5 13510 0.0 11.2 22.55212688 73.54686655
13540 WELD 15,697.3 13540 0.0 11.2 22.55282030 73.54511593
13530 WELD 15,686.0 13530 0.0 11.2 22.55256748 73.54573349
13480 WELD 15,629.2 13480 0.0 11.2 22.55145057 73.54861556
13470 WELD 15,618.0 13470 0.0 11.2 22.55123070 73.54919514
13500 WELD 15,651.6 13500 0.0 10.9 22.55190086 73.54744743
13490 WELD 15,640.4 13490 0.0 11.2 22.55167649 73.54802854
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 48 of 73Criteria:
13750 WELD 15,941.7 13750 0.0 11.9 22.54505431 73.55202073
13740 WELD 15,930.4 13740 0.0 11.3 22.54557677 73.55142901
13770 WELD 15,964.5 13770 0.0 11.6 22.54394913 73.55331269
13760 WELD 15,953.6 13760 0.0 10.9 22.54451273 73.55264686
13710 WELD 15,896.9 13710 0.0 11.4 22.54724900 73.54952461
13700 WELD 15,885.0 13700 0.0 11.9 22.54786507 73.54882132
13730 WELD 15,919.6 13730 0.0 10.8 22.54612120 73.55080597
13720 WELD 15,908.3 13720 0.0 11.3 22.54667301 73.55017904
13830 WELD 16,024.9 13830 0.0 13.8 22.54075358 73.55711199
13820 WELD 16,021.9 13820 0.0 3.0 22.54126253 73.55650662
13790 WELD 15,987.3 13790 0.0 11.5 22.54288204 73.55456306
13780 WELD 15,976.1 13780 0.0 11.2 22.54342950 73.55391375
13810 WELD 16,010.9 13810 0.0 11.0 22.54181882 73.55582835
13800 WELD 15,998.8 13800 0.0 12.1 22.54235500 73.55518855
13600 WELD 15,769.9 13600 0.0 12.3 22.55354766 73.54271508
13590 WELD 15,756.2 13590 0.0 13.7 22.55403295 73.54218360
13610 WELD 15,782.1 13610 0.0 11.2 22.55291551 73.54341650
11000029 WT CHANGE 15,782.1 13610 0.0 0.0 22.55354064 73.54272287 15.90 70000 0.72
13570 WELD 15,733.8 13570 0.0 11.0 22.55349279 73.54342715
13560 WELD 15,719.8 13560 0.0 14.0 22.55326745 73.54398931
13580 WELD 15,744.8 13580 0.0 11.4 22.55380522 73.54273449
11000028 WT CHANGE 15,744.8 13580 0.0 0.0 22.55349673 73.54341842 25.00 70000 0.72
13670 WELD 15,848.4 13670 0.0 11.2 22.54957593 73.54694789
13660 WELD 15,837.3 13660 0.0 11.1 22.55012507 73.54636546
13690 WELD 15,872.1 13690 0.0 12.8 22.54847359 73.54813691
13680 WELD 15,859.6 13680 0.0 12.6 22.54902509 73.54753879
13630 WELD 15,804.0 13630 0.0 11.3 22.55177320 73.54463329
13620 WELD 15,793.3 13620 0.0 10.7 22.55232457 73.54405343
13650 WELD 15,826.3 13650 0.0 11.0 22.55068002 73.54578132
13640 WELD 15,815.3 13640 0.0 11.1 22.55123892 73.54518780
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 49 of 73Criteria:
13920 WELD 16,127.2 13920 0.0 11.3 22.53649725 73.56224250
13910 WELD 16,116.0 13910 0.0 11.2 22.53698168 73.56163193
13940 WELD 16,152.2 13940 0.0 12.5 22.53552528 73.56348763
13930 WELD 16,138.5 13930 0.0 13.7 22.53601182 73.56286096
13880 WELD 16,082.5 13880 0.0 11.2 22.53847176 73.55977822
13870 WELD 16,071.2 13870 0.0 11.3 22.53898520 73.55914652
13900 WELD 16,104.9 13900 0.0 11.1 22.53747447 73.56101397
13890 WELD 16,093.7 13890 0.0 11.2 22.53797017 73.56039763
13990 WELD 16,207.8 13990 0.0 12.4 22.53314743 73.56660098
13980 WELD 16,195.2 13980 0.0 12.6 22.53360483 73.56600337
14000 WELD 16,220.2 14000 0.0 10.6 22.53313710 73.56618571
11000031 WT CHANGE 16,220.2 14000 0.0 0.0 22.53314716 73.56658998 15.90 70000 0.72
13960 WELD 16,172.9 13960 0.0 11.2 22.53443991 73.56495260
13950 WELD 16,164.6 13950 0.0 8.3 22.53495820 73.56425716
11000030 WT CHANGE 16,195.2 13980 0.0 0.0 22.53406431 73.56540594 25.00 70000 0.72
13970 WELD 16,184.1 13970 0.0 11.1 22.53407010 73.56539841
13860 WELD 16,059.7 13860 0.0 11.5 22.53940216 73.55867149
13850 WELD 16,050.8 13850 0.0 8.9 22.53994535 73.55800554
13840 WELD 16,038.7 13840 0.0 12.1 22.54055848 73.55723732
14060 WELD 16,285.6 14060 0.0 13.9 22.53336123 73.56342359
14050 WELD 16,274.9 14050 0.0 10.7 22.53330585 73.56391745
14080 WELD 16,313.3 14080 0.0 14.0 22.53348467 73.56239945
14070 WELD 16,299.5 14070 0.0 13.8 22.53340515 73.56296855
14020 WELD 16,240.3 14020 0.0 11.4 22.53320702 73.56524992
14010 WELD 16,230.9 14010 0.0 9.4 22.53318133 73.56568379
14040 WELD 16,263.2 14040 0.0 11.7 22.53325214 73.56440746
14030 WELD 16,251.7 14030 0.0 11.5 22.53321975 73.56486357
14100 WELD 16,339.2 14100 0.0 11.2 22.53364137 73.56127457
14090 WELD 16,327.3 14090 0.0 11.9 22.53356212 73.56183901
14110 WELD 16,350.4 14110 0.0 11.3 22.53369649 73.56078937
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 50 of 73Criteria:
14230 WELD 16,490.5 14230 0.0 13.7 22.53446623 73.55504818
14220 WELD 16,478.6 14220 0.0 11.9 22.53438051 73.55553701
14250 WELD 16,517.8 14250 0.0 11.2 22.53468493 73.55395143
14240 WELD 16,504.2 14240 0.0 13.6 22.53456251 73.55453317
14190 WELD 16,441.9 14190 0.0 13.3 22.53411950 73.55708657
14180 WELD 16,430.5 14180 0.0 11.4 22.53404780 73.55756354
14210 WELD 16,467.4 14210 0.0 11.2 22.53429537 73.55604657
14200 WELD 16,455.2 14200 0.0 12.2 22.53419453 73.55660181
14310 WELD 16,584.6 14310 0.0 11.1 22.53522306 73.55101245
14300 WELD 16,573.8 14300 0.0 10.8 22.53513843 73.55148538
11000032 WT CHANGE 16,606.1 14330 0.0 0.0 22.53530163 73.55055145 25.00 70000 0.72
14320 WELD 16,595.7 14320 0.0 10.5 22.53530003 73.55056057
14270 WELD 16,540.2 14270 0.0 11.0 22.53488965 73.55289941
14260 WELD 16,529.0 14260 0.0 11.1 22.53480459 73.55337924
14290 WELD 16,562.5 14290 0.0 11.3 22.53505398 73.55195922
14280 WELD 16,551.2 14280 0.0 11.3 22.53497247 73.55242690
14170 WELD 16,419.4 14170 0.0 11.1 22.53397670 73.55806383
14140 WELD 16,384.2 14140 0.0 11.8 22.53383563 73.55942495
14130 WELD 16,372.9 14130 0.0 11.3 22.53378951 73.55987783
14160 WELD 16,407.2 14160 0.0 12.2 22.53393261 73.55850724
14150 WELD 16,396.0 14150 0.0 11.2 22.53388188 73.55897270
14120 WELD 16,361.7 14120 0.0 11.3 22.53374264 73.56033421
14330 WELD 16,606.2 14330 0.0 12.3 22.53538008 73.55010206
14380 WELD 16,664.8 14380 0.0 14.1 22.53589580 73.54764450
14370 WELD 16,653.7 14370 0.0 11.1 22.53578177 73.54813893
14390 WELD 16,678.9 14390 0.0 11.3 22.53600695 73.54715842
14340 WELD 16,618.5 14340 0.0 10.5 22.53545136 73.54966716
11000033 WT CHANGE 16,618.4 14340 0.0 0.0 22.53538184 73.55009132 15.90 70000 0.72
14360 WELD 16,642.4 14360 0.0 11.3 22.53564575 73.54870278
14350 WELD 16,629.0 14350 0.0 13.4 22.53555571 73.54915853
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 51 of 73Criteria:
14550 WELD 16,866.0 14550 0.0 11.1 22.53825668 73.53892724
14540 WELD 16,853.9 14540 0.0 12.0 22.53809833 73.53944395
14570 WELD 16,887.6 14570 0.0 11.7 22.53856387 73.53791807
14560 WELD 16,877.1 14560 0.0 10.5 22.53841934 73.53840407
14510 WELD 16,819.6 14510 0.0 11.2 22.53763944 73.54097379
14500 WELD 16,807.7 14500 0.0 11.9 22.53748780 73.54148502
14530 WELD 16,842.1 14530 0.0 11.8 22.53794797 73.53994683
14520 WELD 16,830.8 14520 0.0 11.4 22.53780158 73.54044371
14630 WELD 16,957.1 14630 0.0 11.3 22.53945461 73.53499118
14620 WELD 16,945.3 14620 0.0 11.8 22.53930625 73.53547481
14650 WELD 16,979.5 14650 0.0 12.9 22.53975727 73.53401734
14640 WELD 16,968.5 14640 0.0 11.1 22.53961091 73.53449406
14590 WELD 16,910.9 14590 0.0 11.0 22.53885117 73.53695447
14580 WELD 16,899.3 14580 0.0 11.7 22.53869665 73.53745653
14610 WELD 16,933.9 14610 0.0 11.4 22.53914813 73.53597868
14600 WELD 16,922.0 14600 0.0 11.9 22.53900612 73.53645331
14490 WELD 16,796.3 14490 0.0 11.4 22.53733684 73.54199687
14400 WELD 16,690.2 14400 0.0 10.9 22.53616895 73.54655831
14460 WELD 16,760.2 14460 0.0 13.6 22.53688294 73.54358235
14450 WELD 16,749.0 14450 0.0 11.3 22.53677177 73.54405680
14480 WELD 16,785.0 14480 0.0 11.3 22.53719101 73.54250040
14470 WELD 16,773.9 14470 0.0 11.1 22.53699388 73.54310985
14420 WELD 16,714.9 14420 0.0 11.6 22.53638898 73.54560025
14410 WELD 16,701.1 14410 0.0 13.8 22.53628219 73.54607118
14440 WELD 16,737.7 14440 0.0 11.3 22.53666002 73.54453401
14430 WELD 16,726.4 14430 0.0 11.3 22.53654312 73.54502428
14670 WELD 17,003.7 14670 0.0 11.1 22.54007408 73.53302304
14660 WELD 16,992.5 14660 0.0 11.2 22.53989818 73.53355235
14690 WELD 17,026.5 14690 0.0 11.3 22.54035720 73.53209783
14680 WELD 17,014.8 14680 0.0 11.7 22.54021719 73.53255688
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 52 of 73Criteria:
14990 WELD 17,372.7 14990 0.0 11.2 22.54456917 73.52106265
14880 WELD 17,244.6 14880 0.0 11.3 22.54351088 73.52316198
14870 WELD 17,230.6 14870 0.0 14.0 22.54325941 73.52368782
14900 WELD 17,267.3 14900 0.0 11.3 22.54412989 73.52198783
14890 WELD 17,255.9 14890 0.0 11.3 22.54384984 73.52252578
14840 WELD 17,196.4 14840 0.0 11.4 22.54262280 73.52517873
14830 WELD 17,185.4 14830 0.0 11.0 22.54238585 73.52574120
14860 WELD 17,219.2 14860 0.0 11.4 22.54302681 73.52420128
14850 WELD 17,207.8 14850 0.0 11.4 22.54281238 73.52470285
14960 WELD 17,338.1 14960 0.0 10.9 22.54478865 73.52111716
14950 WELD 17,326.8 14950 0.0 11.3 22.54478394 73.52110972
14980 WELD 17,361.3 14980 0.0 11.4 22.54470292 73.52122648
14970 WELD 17,349.0 14970 0.0 12.3 22.54476599 73.52115311
14920 WELD 17,290.1 14920 0.0 14.0 22.54457668 73.52127603
14910 WELD 17,278.6 14910 0.0 11.5 22.54442747 73.52144227
14940 WELD 17,315.4 14940 0.0 11.5 22.54475095 73.52113790
14930 WELD 17,304.2 14930 0.0 11.2 22.54467065 73.52118100
14820 WELD 17,171.8 14820 0.0 13.6 22.54221933 73.52620075
14710 WELD 17,050.1 14710 0.0 11.3 22.54065182 73.53115652
14700 WELD 17,037.8 14700 0.0 12.3 22.54050888 73.53161838
14730 WELD 17,072.5 14730 0.0 11.8 22.54095724 73.53020065
14720 WELD 17,061.4 14720 0.0 11.1 22.54081399 73.53066042
14790 WELD 17,139.0 14790 0.0 10.9 22.54178189 73.52753049
14780 WELD 17,128.1 14780 0.0 10.9 22.54164966 73.52796327
14810 WELD 17,160.9 14810 0.0 11.0 22.54206327 73.52665182
14800 WELD 17,149.9 14800 0.0 10.9 22.54191698 73.52709586
14750 WELD 17,095.3 14750 0.0 10.7 22.54124547 73.52928164
14740 WELD 17,084.3 14740 0.0 11.1 22.54109464 73.52975286
14770 WELD 17,117.2 14770 0.0 10.9 22.54151245 73.52840617
14760 WELD 17,106.1 14760 0.0 11.1 22.54138228 73.52883730
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 53 of 73Criteria:
15210 WELD 17,632.9 15210 0.0 11.0 22.54203153 73.51722698
15200 WELD 17,621.5 15200 0.0 11.4 22.54219567 73.51734393
15230 WELD 17,654.5 15230 0.0 10.9 22.54170604 73.51699382
15220 WELD 17,643.9 15220 0.0 10.6 22.54186707 73.51710967
15170 WELD 17,587.6 15170 0.0 11.2 22.54268826 73.51769368
15160 WELD 17,576.2 15160 0.0 11.5 22.54285643 73.51781171
15190 WELD 17,610.2 15190 0.0 11.4 22.54235971 73.51746064
15180 WELD 17,598.8 15180 0.0 11.3 22.54252269 73.51757665
15290 WELD 17,722.2 15290 0.0 11.3 22.54079828 73.51622484
15280 WELD 17,710.7 15280 0.0 11.5 22.54094060 73.51636531
15250 WELD 17,676.8 15250 0.0 11.3 22.54138895 73.51676401
15240 WELD 17,665.5 15240 0.0 11.3 22.54154884 73.51687965
15270 WELD 17,699.4 15270 0.0 11.3 22.54108300 73.51650582
15260 WELD 17,688.1 15260 0.0 11.3 22.54122564 73.51664651
15150 WELD 17,564.4 15150 0.0 11.8 22.54302025 73.51792750
15040 WELD 17,428.4 15040 0.0 11.2 22.54427282 73.51991509
15030 WELD 17,417.4 15030 0.0 11.1 22.54428478 73.52019454
15060 WELD 17,453.3 15060 0.0 13.9 22.54430232 73.51930768
15050 WELD 17,439.6 15050 0.0 13.6 22.54428129 73.51961832
15000 WELD 17,383.8 15000 0.0 11.2 22.54446383 73.52087989
15020 WELD 17,406.1 15020 0.0 11.3 22.54431653 73.52045216
15010 WELD 17,395.0 15010 0.0 11.1 22.54437046 73.52068700
15120 WELD 17,530.4 15120 0.0 11.3 22.54355978 73.51826290
15110 WELD 17,516.4 15110 0.0 14.0 22.54376553 73.51836480
15140 WELD 17,553.2 15140 0.0 11.2 22.54318607 73.51804401
15130 WELD 17,541.7 15130 0.0 11.5 22.54335086 73.51815982
15080 WELD 17,477.8 15080 0.0 12.6 22.54444631 73.51851791
15070 WELD 17,467.2 15070 0.0 10.6 22.54436133 73.51892666
15100 WELD 17,502.7 15100 0.0 13.7 22.54395780 73.51846329
15090 WELD 17,490.4 15090 0.0 12.3 22.54417607 73.51853583
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 54 of 73Criteria:
15310 WELD 17,744.9 15310 0.0 11.2 22.54051165 73.51594190
15300 WELD 17,733.5 15300 0.0 11.4 22.54065437 73.51608284
15530 WELD 17,994.4 15530 0.0 12.3 22.53906467 73.51226957
15520 WELD 17,982.0 15520 0.0 12.5 22.53896499 73.51235739
15550 WELD 18,019.0 15550 0.0 12.1 22.53933098 73.51142247
15540 WELD 18,006.7 15540 0.0 12.3 22.53919482 73.51184694
15490 WELD 17,944.8 15490 0.0 12.3 22.53816240 73.51331756
15480 WELD 17,932.4 15480 0.0 12.4 22.53802990 73.51374650
15510 WELD 17,969.6 15510 0.0 12.4 22.53877478 73.51255636
15500 WELD 17,957.1 15500 0.0 12.4 22.53852683 73.51283650
15570 WELD 18,043.4 15570 0.0 12.4 22.54003480 73.51053848
15560 WELD 18,031.1 15560 0.0 12.3 22.53967596 73.51099508
15580 WELD 18,055.8 15580 0.0 12.4 22.54040189 73.51007624
15470 WELD 17,919.9 15470 0.0 12.5 22.53822274 73.51367662
15370 WELD 17,814.9 15370 0.0 11.6 22.53964948 73.51509001
15360 WELD 17,802.6 15360 0.0 12.3 22.53979276 73.51523171
15390 WELD 17,837.7 15390 0.0 11.4 22.53935620 73.51480022
15380 WELD 17,826.5 15380 0.0 11.3 22.53950055 73.51494299
15330 WELD 17,766.9 15330 0.0 11.2 22.54022707 73.51566073
15320 WELD 17,756.1 15320 0.0 10.8 22.54036859 73.51580062
15350 WELD 17,791.1 15350 0.0 11.4 22.53994657 73.51538318
15340 WELD 17,778.1 15340 0.0 13.0 22.54008811 73.51552318
15450 WELD 17,905.0 15450 0.0 11.3 22.53850622 73.51395783
15440 WELD 17,893.8 15440 0.0 11.2 22.53864535 73.51409595
15460 WELD 17,916.3 15460 0.0 3.6 22.53836473 73.51381749
11000034 WT CHANGE 17,916.3 15460 0.0 0.0 22.53849941 73.51395108 23.80 70000 0.72
15410 WELD 17,860.4 15410 0.0 11.4 22.53907111 73.51451792
15400 WELD 17,849.2 15400 0.0 11.3 22.53921417 73.51465957
15430 WELD 17,883.0 15430 0.0 10.9 22.53878662 73.51423603
15420 WELD 17,871.8 15420 0.0 11.2 22.53892915 73.51437726
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 55 of 73Criteria:
15610 WELD 18,092.6 15610 0.0 12.4 22.54150473 73.50873187
15600 WELD 18,080.7 15600 0.0 11.9 22.54113895 73.50917123
15630 WELD 18,117.3 15630 0.0 12.3 22.54170736 73.50855388
15620 WELD 18,104.9 15620 0.0 12.4 22.54163446 73.50860732
15590 WELD 18,068.3 15590 0.0 12.4 22.54076897 73.50962413
15860 WELD 18,395.7 15860 0.0 12.3 22.53945191 73.50882890
15850 WELD 18,383.3 15850 0.0 12.4 22.53948888 73.50876707
15880 WELD 18,420.6 15880 0.0 2.7 22.53946088 73.50840707
15870 WELD 18,408.1 15870 0.0 12.5 22.53905659 73.50897238
15820 WELD 18,346.3 15820 0.0 12.4 22.53930180 73.50889584
15810 WELD 18,333.9 15810 0.0 12.4 22.53916796 73.50901929
15840 WELD 18,371.0 15840 0.0 12.3 22.53945057 73.50878328
15830 WELD 18,358.6 15830 0.0 12.4 22.53938552 73.50882893
15800 WELD 18,321.5 15800 0.0 12.4 22.53899870 73.50918848
15690 WELD 18,191.4 15690 0.0 12.4 22.54201716 73.50801454
15680 WELD 18,179.1 15680 0.0 12.3 22.54196217 73.50804834
15710 WELD 18,209.9 15710 0.0 13.3 22.54098168 73.50885308
15700 WELD 18,203.8 15700 0.0 6.1 22.54150229 73.50843217
15650 WELD 18,142.0 15650 0.0 12.5 22.54157432 73.50839743
15640 WELD 18,129.6 15640 0.0 12.4 22.54117900 73.50893918
15670 WELD 18,166.7 15670 0.0 12.3 22.54187647 73.50811694
15660 WELD 18,154.5 15660 0.0 12.2 22.54174086 73.50823814
15770 WELD 18,284.3 15770 0.0 12.4 22.53871435 73.50983640
15760 WELD 18,271.9 15760 0.0 12.4 22.53902956 73.50979428
15790 WELD 18,309.2 15790 0.0 12.2 22.53875593 73.50944682
15780 WELD 18,296.7 15780 0.0 12.6 22.53840241 73.50987686
15730 WELD 18,234.8 15730 0.0 12.4 22.54012017 73.50946371
15720 WELD 18,223.3 15720 0.0 11.5 22.54069001 73.50902367
15750 WELD 18,259.4 15750 0.0 12.5 22.53938904 73.50969134
15740 WELD 18,247.2 15740 0.0 12.2 22.53974344 73.50959922
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 56 of 73Criteria:
15940 WELD 18,475.2 15940 0.0 12.3 22.53760062 73.50973370
15930 WELD 18,462.9 15930 0.0 12.4 22.53814284 73.50931448
15960 WELD 18,499.9 15960 0.0 12.5 22.53652900 73.51055573
15950 WELD 18,487.6 15950 0.0 12.3 22.53706273 73.51014538
15900 WELD 18,435.7 15900 0.0 12.2 22.53936520 73.50843009
15890 WELD 18,423.3 15890 0.0 12.4 22.53942462 73.50847153
15920 WELD 18,450.4 15920 0.0 12.5 22.53830265 73.50928368
15910 WELD 18,447.9 15910 0.0 2.5 22.53882761 73.50885793
16180 WELD 18,772.4 16180 0.0 12.4 22.53674102 73.50671193
16150 WELD 18,735.3 16150 0.0 12.5 22.53828963 73.50539686
16140 WELD 18,722.8 16140 0.0 12.5 22.53811759 73.50556347
16170 WELD 18,760.1 16170 0.0 12.3 22.53724170 73.50627722
16160 WELD 18,747.8 16160 0.0 12.3 22.53777018 73.50583521
16130 WELD 18,710.4 16130 0.0 12.4 22.53791699 73.50576557
16020 WELD 18,574.5 16020 0.0 12.4 22.53521901 73.51059706
16010 WELD 18,562.1 16010 0.0 12.4 22.53491316 73.51116230
16040 WELD 18,599.3 16040 0.0 12.5 22.53599273 73.50943335
16030 WELD 18,586.9 16030 0.0 12.4 22.53559844 73.51001045
15980 WELD 18,524.7 15980 0.0 12.4 22.53548521 73.51129501
15970 WELD 18,512.4 15970 0.0 12.4 22.53600527 73.51093263
16000 WELD 18,549.7 16000 0.0 12.4 22.53465654 73.51169934
15990 WELD 18,537.2 15990 0.0 12.5 22.53497691 73.51164049
16100 WELD 18,673.3 16100 0.0 12.3 22.53671492 73.50745521
16090 WELD 18,661.2 16090 0.0 12.2 22.53632464 73.50803417
16120 WELD 18,698.1 16120 0.0 12.3 22.53750776 73.50632711
16110 WELD 18,685.7 16110 0.0 12.4 22.53710423 73.50688987
16060 WELD 18,624.1 16060 0.0 12.4 22.53528609 73.50973130
16050 WELD 18,611.8 16050 0.0 12.3 22.53545949 73.50985331
16080 WELD 18,648.8 16080 0.0 12.4 22.53594036 73.50860950
16070 WELD 18,636.5 16070 0.0 12.3 22.53556203 73.50919189
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 57 of 73Criteria:
16480 WELD 19,141.5 16480 0.0 12.6 22.53346109 73.50457643
16470 WELD 19,129.1 16470 0.0 12.4 22.53386665 73.50443397
16460 WELD 19,115.7 16460 0.0 13.4 22.53426385 73.50426244
16350 WELD 18,980.9 16350 0.0 12.3 22.53668622 73.50438706
16340 WELD 18,968.6 16340 0.0 12.3 22.53699720 73.50407135
16370 WELD 19,006.3 16370 0.0 11.6 22.53602849 73.50450191
16360 WELD 18,993.2 16360 0.0 13.1 22.53633531 73.50447125
16310 WELD 18,931.3 16310 0.0 12.3 22.53695141 73.50405991
16300 WELD 18,918.9 16300 0.0 12.4 22.53653587 73.50460869
16330 WELD 18,956.1 16330 0.0 12.5 22.53714702 73.50389744
16320 WELD 18,943.6 16320 0.0 12.5 22.53706228 73.50396520
16430 WELD 19,079.6 16430 0.0 12.4 22.53582708 73.50317359
16420 WELD 19,067.1 16420 0.0 12.5 22.53542368 73.50367042
16450 WELD 19,104.4 16450 0.0 11.2 22.53473757 73.50400403
16440 WELD 19,092.0 16440 0.0 12.4 22.53528069 73.50358900
16390 WELD 19,030.2 16390 0.0 12.0 22.53550294 73.50445920
16380 WELD 19,017.9 16380 0.0 12.3 22.53573435 73.50450573
16410 WELD 19,054.6 16410 0.0 12.6 22.53533059 73.50405574
16400 WELD 19,042.2 16400 0.0 12.4 22.53526196 73.50441376
16190 WELD 18,784.8 16190 0.0 12.4 22.53621970 73.50714845
16210 WELD 18,809.5 16210 0.0 12.4 22.53514385 73.50798927
16200 WELD 18,797.1 16200 0.0 12.3 22.53568252 73.50758083
16270 WELD 18,883.9 16270 0.0 12.0 22.53551632 73.50623505
16260 WELD 18,871.8 16260 0.0 12.1 22.53513955 73.50683128
16290 WELD 18,906.4 16290 0.0 12.4 22.53621746 73.50511001
16280 WELD 18,895.9 16280 0.0 10.5 22.53585180 73.50567379
16230 WELD 18,834.3 16230 0.0 12.4 22.53433516 73.50834946
16220 WELD 18,821.9 16220 0.0 12.3 22.53463607 73.50832023
16250 WELD 18,859.0 16250 0.0 12.8 22.53475523 73.50741479
16240 WELD 18,846.7 16240 0.0 12.4 22.53437959 73.50800203
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 58 of 73Criteria:
16520 WELD 19,191.3 16520 0.0 11.2 22.53389192 73.50307974
16510 WELD 19,178.9 16510 0.0 12.5 22.53349246 73.50365087
16540 WELD 19,216.1 16540 0.0 12.3 22.53439844 73.50251722
16530 WELD 19,202.6 16530 0.0 13.5 22.53417808 73.50276516
16500 WELD 19,166.4 16500 0.0 12.4 22.53335823 73.50407465
16490 WELD 19,154.0 16490 0.0 12.4 22.53336118 73.50437586
16600 WELD 19,290.4 16600 0.0 12.5 22.53160680 73.50445354
16590 WELD 19,278.0 16590 0.0 12.4 22.53185863 73.50448356
16620 WELD 19,315.0 16620 0.0 12.6 22.53142212 73.50404023
16610 WELD 19,302.9 16610 0.0 12.1 22.53142020 73.50434696
16560 WELD 19,240.9 16560 0.0 12.3 22.53336617 73.50341645
16550 WELD 19,228.4 16550 0.0 12.5 22.53388798 73.50298468
16580 WELD 19,265.7 16580 0.0 12.3 22.53229908 73.50426933
16570 WELD 19,253.2 16570 0.0 12.5 22.53283261 73.50385519
16680 WELD 19,389.7 16680 0.0 12.3 22.53051815 73.50463985
16670 WELD 19,377.0 16670 0.0 12.7 22.53096243 73.50422003
16700 WELD 19,414.3 16700 0.0 12.6 22.52950769 73.50530742
16690 WELD 19,402.0 16690 0.0 12.3 22.52999143 73.50500783
16640 WELD 19,340.1 16640 0.0 11.4 22.53168691 73.50348534
16630 WELD 19,327.6 16630 0.0 12.5 22.53152032 73.50364912
16660 WELD 19,364.8 16660 0.0 12.3 22.53140449 73.50378273
16650 WELD 19,351.5 16650 0.0 13.3 22.53173281 73.50346168
16760 WELD 19,488.6 16760 0.0 12.3 22.52982231 73.50429191
16750 WELD 19,476.3 16750 0.0 12.4 22.52971302 73.50439317
16780 WELD 19,513.3 16780 0.0 12.4 22.52920115 73.50495062
16770 WELD 19,500.9 16770 0.0 12.4 22.52953079 73.50460500
16720 WELD 19,439.3 16720 0.0 12.1 22.52865887 73.50572175
16710 WELD 19,426.9 16710 0.0 12.4 22.52903091 73.50559632
16740 WELD 19,464.0 16740 0.0 12.3 22.52937112 73.50481024
16730 WELD 19,451.5 16730 0.0 12.5 22.52902662 73.50524584
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 59 of 73Criteria:
16850 WELD 19,598.9 16850 0.0 12.0 22.52593128 73.50742729
16840 WELD 19,586.7 16840 0.0 12.2 22.52637263 73.50717472
16870 WELD 19,623.3 16870 0.0 12.2 22.52514523 73.50777842
16860 WELD 19,610.9 16860 0.0 12.4 22.52552906 73.50761387
16810 WELD 19,550.4 16810 0.0 12.4 22.52785444 73.50617219
16800 WELD 19,538.0 16800 0.0 12.4 22.52838205 73.50577158
16830 WELD 19,574.7 16830 0.0 12.0 22.52684019 73.50687972
16820 WELD 19,562.8 16820 0.0 12.0 22.52734089 73.50653756
16930 WELD 19,693.1 16930 0.0 12.4 22.52394424 73.50799145
16920 WELD 19,685.2 16920 0.0 7.9 22.52443806 73.50764540
16950 WELD 19,717.8 16950 0.0 9.4 22.52425355 73.50713125
16940 WELD 19,705.6 16940 0.0 12.2 22.52402739 73.50766018
16890 WELD 19,647.9 16890 0.0 12.4 22.52444314 73.50800570
16880 WELD 19,635.5 16880 0.0 12.3 22.52477915 73.50791129
16910 WELD 19,672.8 16910 0.0 12.4 22.52450288 73.50754319
16900 WELD 19,660.3 16900 0.0 12.5 22.52412899 73.50806822
16790 WELD 19,525.7 16790 0.0 12.3 22.52880350 73.50535162
16960 WELD 19,727.2 16960 0.0 12.4 22.52447414 73.50661284
17020 WELD 19,791.9 17020 0.0 12.2 22.52584133 73.50381540
17010 WELD 19,779.4 17010 0.0 12.5 22.52545126 73.50438420
17040 WELD 19,816.4 17040 0.0 12.4 22.52588680 73.50381387
17030 WELD 19,804.2 17030 0.0 12.3 22.52587366 73.50380510
16980 WELD 19,751.7 16980 0.0 3.0 22.52486996 73.50566494
16970 WELD 19,739.5 16970 0.0 12.2 22.52463575 73.50619349
17000 WELD 19,767.1 17000 0.0 12.4 22.52509163 73.50497550
16990 WELD 19,754.8 16990 0.0 12.3 22.52508502 73.50515656
17060 WELD 19,841.2 17060 0.0 12.4 22.52591454 73.50383272
17050 WELD 19,828.9 17050 0.0 12.4 22.52590016 73.50382282
17080 WELD 19,865.9 17080 0.0 12.3 22.52489849 73.50454326
17070 WELD 19,853.6 17070 0.0 12.3 22.52540566 73.50418778
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 60 of 73Criteria:
17190 WELD 20,001.7 17190 0.0 12.0 22.52327232 73.50402143
17180 WELD 19,989.5 17180 0.0 12.2 22.52344871 73.50380603
17210 WELD 20,026.0 17210 0.0 12.1 22.52235663 73.50488076
17200 WELD 20,013.7 17200 0.0 12.3 22.52286083 73.50444055
17150 WELD 19,952.3 17150 0.0 12.5 22.52334776 73.50416030
17140 WELD 19,940.0 17140 0.0 12.3 22.52337456 73.50444543
17170 WELD 19,977.1 17170 0.0 12.3 22.52355939 73.50365812
17160 WELD 19,964.7 17160 0.0 12.4 22.52349266 73.50370985
17270 WELD 20,099.8 17270 0.0 12.4 22.52357781 73.50211488
17260 WELD 20,087.4 17260 0.0 12.5 22.52320620 73.50267149
17290 WELD 20,124.5 17290 0.0 12.2 22.52436897 73.50097156
17280 WELD 20,112.2 17280 0.0 12.3 22.52397243 73.50153557
17230 WELD 20,050.8 17230 0.0 12.3 22.52229976 73.50439834
17220 WELD 20,038.1 17220 0.0 12.7 22.52204224 73.50494300
17250 WELD 20,075.5 17250 0.0 11.9 22.52289117 73.50325104
17240 WELD 20,063.1 17240 0.0 12.4 22.52259029 73.50382239
17130 WELD 19,927.6 17130 0.0 12.5 22.52345550 73.50466870
17100 WELD 19,890.5 17100 0.0 12.4 22.52424974 73.50468470
17090 WELD 19,878.2 17090 0.0 12.3 22.52457360 73.50461433
17120 WELD 19,915.3 17120 0.0 12.2 22.52365100 73.50476150
17110 WELD 19,902.9 17110 0.0 12.4 22.52393826 73.50473987
17350 WELD 20,198.6 17350 0.0 12.3 22.52285362 73.50178167
17340 WELD 20,186.3 17340 0.0 12.3 22.52336799 73.50141075
17370 WELD 20,223.1 17370 0.0 12.6 22.52186006 73.50246706
17360 WELD 20,210.9 17360 0.0 12.3 22.52235116 73.50213451
17310 WELD 20,149.2 17310 0.0 12.4 22.52494784 73.50022531
17300 WELD 20,136.7 17300 0.0 12.5 22.52476047 73.50042637
17330 WELD 20,173.9 17330 0.0 12.4 22.52388572 73.50103100
17320 WELD 20,161.6 17320 0.0 12.3 22.52441113 73.50063855
17380 WELD 20,235.7 17380 0.0 12.3 22.52137134 73.50279913
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 61 of 73Criteria:
17680 WELD 20,605.7 17680 0.0 12.4 22.51946865 73.50063394
17670 WELD 20,593.4 17670 0.0 12.3 22.51908023 73.50118578
17640 WELD 20,556.4 17640 0.0 12.4 22.51792564 73.50293424
17630 WELD 20,544.0 17630 0.0 12.4 22.51767041 73.50349171
17660 WELD 20,581.1 17660 0.0 12.3 22.51869427 73.50174145
17650 WELD 20,568.7 17650 0.0 12.3 22.51830699 73.50233264
17520 WELD 20,408.0 17520 0.0 12.3 22.51962459 73.50259773
17510 WELD 20,395.6 17510 0.0 12.4 22.51927741 73.50319440
17540 WELD 20,432.6 17540 0.0 12.4 22.52033947 73.50139878
17530 WELD 20,420.3 17530 0.0 12.4 22.51998311 73.50199540
17480 WELD 20,358.6 17480 0.0 12.3 22.51958781 73.50364286
17470 WELD 20,346.3 17470 0.0 12.3 22.52010733 73.50322057
17500 WELD 20,383.3 17500 0.0 12.3 22.51894243 73.50379530
17490 WELD 20,370.9 17490 0.0 12.4 22.51925799 73.50372898
17600 WELD 20,506.6 17600 0.0 12.5 22.51898513 73.50257959
17590 WELD 20,494.4 17590 0.0 12.2 22.51947148 73.50211020
17620 WELD 20,531.5 17620 0.0 12.4 22.51794135 73.50348698
17610 WELD 20,519.1 17610 0.0 12.4 22.51846959 73.50303200
17560 WELD 20,457.5 17560 0.0 12.3 22.52083324 73.50076236
17550 WELD 20,445.0 17550 0.0 12.5 22.52072025 73.50087233
17580 WELD 20,482.0 17580 0.0 12.4 22.51992841 73.50165871
17570 WELD 20,469.8 17570 0.0 12.3 22.52038565 73.50120940
17460 WELD 20,334.0 17460 0.0 12.3 22.52060298 73.50275186
17430 WELD 20,296.8 17430 0.0 12.5 22.52148547 73.50180905
17420 WELD 20,284.7 17420 0.0 12.1 22.52145143 73.50182178
17450 WELD 20,321.6 17450 0.0 12.4 22.52107843 73.50229286
17440 WELD 20,309.3 17440 0.0 12.4 22.52131586 73.50201490
17390 WELD 20,247.9 17390 0.0 12.4 22.52089797 73.50309525
17410 WELD 20,272.2 17410 0.0 12.5 22.52108387 73.50237194
17400 WELD 20,260.3 17400 0.0 11.9 22.52073239 73.50296854
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 62 of 73Criteria:
17850 WELD 20,802.9 17850 0.0 12.3 22.51805758 73.50004101
17840 WELD 20,790.4 17840 0.0 12.5 22.51787282 73.50029836
17870 WELD 20,827.6 17870 0.0 12.3 22.51831022 73.49978616
17860 WELD 20,815.2 17860 0.0 12.4 22.51820109 73.49989354
17810 WELD 20,765.7 17810 0.0 12.2 22.51704557 73.50162591
17800 WELD 20,753.1 17800 0.0 12.6 22.51694129 73.50204326
17830 WELD 20,781.0 17830 0.0 9.4 22.51782860 73.50048225
17820 WELD 20,777.9 17820 0.0 3.1 22.51744447 73.50103254
17930 WELD 20,901.6 17930 0.0 12.4 22.51646275 73.50150782
17920 WELD 20,889.2 17920 0.0 12.4 22.51699472 73.50106984
17950 WELD 20,925.6 17950 0.0 13.2 22.51596892 73.50151892
17940 WELD 20,914.0 17940 0.0 11.6 22.51598417 73.50182124
17890 WELD 20,852.2 17890 0.0 12.4 22.51828574 73.49986606
17880 WELD 20,840.0 17880 0.0 12.3 22.51831498 73.49980701
17910 WELD 20,877.0 17910 0.0 12.3 22.51753238 73.50060839
17900 WELD 20,864.6 17900 0.0 12.3 22.51806748 73.50012538
17790 WELD 20,741.2 17790 0.0 11.9 22.51705429 73.50223355
17700 WELD 20,630.7 17700 0.0 12.2 22.52005964 73.49987910
17690 WELD 20,618.1 17690 0.0 12.6 22.51984595 73.50012049
17760 WELD 20,704.5 17760 0.0 11.8 22.51785710 73.50212086
17750 WELD 20,692.3 17750 0.0 12.2 22.51839096 73.50164757
17780 WELD 20,728.8 17780 0.0 12.4 22.51718400 73.50240542
17770 WELD 20,716.4 17770 0.0 12.4 22.51733338 73.50254494
17720 WELD 20,655.2 17720 0.0 12.4 22.51961476 73.50040255
17710 WELD 20,642.8 17710 0.0 12.3 22.51983599 73.50014471
17740 WELD 20,679.8 17740 0.0 12.4 22.51890242 73.50117025
17730 WELD 20,667.5 17730 0.0 12.3 22.51929518 73.50075536
17970 WELD 20,951.2 17970 0.0 12.3 22.51665503 73.50029672
17960 WELD 20,938.9 17960 0.0 12.3 22.51624724 73.50095879
17980 WELD 20,963.5 17980 0.0 12.5 22.51703907 73.49967883
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 63 of 73Criteria:
18180 WELD 21,197.6 18180 0.0 13.9 22.51466236 73.50120230
18170 WELD 21,184.6 18170 0.0 13.0 22.51497527 73.50085024
18200 WELD 21,222.3 18200 0.0 12.3 22.51352504 73.50232966
18190 WELD 21,211.5 18190 0.0 10.8 22.51412155 73.50174534
18140 WELD 21,148.6 18140 0.0 12.1 22.51574812 73.49994070
18130 WELD 21,136.4 18130 0.0 12.2 22.51594554 73.49969645
18160 WELD 21,172.9 18160 0.0 11.7 22.51526132 73.50051830
18150 WELD 21,160.7 18150 0.0 12.1 22.51551703 73.50021730
18260 WELD 21,296.3 18260 0.0 12.4 22.51210795 73.50257780
18250 WELD 21,284.0 18250 0.0 12.3 22.51175792 73.50322042
18280 WELD 21,320.3 18280 0.0 13.2 22.51288957 73.50129253
18270 WELD 21,308.7 18270 0.0 11.6 22.51248634 73.50193312
18220 WELD 21,246.7 18220 0.0 12.5 22.51251872 73.50313463
18210 WELD 21,234.7 18210 0.0 12.1 22.51304499 73.50271351
18240 WELD 21,271.7 18240 0.0 12.4 22.51165168 73.50366143
18230 WELD 21,259.2 18230 0.0 12.4 22.51201497 73.50352199
18120 WELD 21,124.1 18120 0.0 12.4 22.51611249 73.49948839
18010 WELD 21,000.3 18010 0.0 12.3 22.51803487 73.49832287
18000 WELD 20,987.8 18000 0.0 12.4 22.51776203 73.49865730
18030 WELD 21,024.8 18030 0.0 12.4 22.51777775 73.49865067
18020 WELD 21,012.6 18020 0.0 12.3 22.51800789 73.49838022
17990 WELD 20,975.9 17990 0.0 11.9 22.51743229 73.49906974
18090 WELD 21,099.1 18090 0.0 9.7 22.51599339 73.50029524
18080 WELD 21,086.8 18080 0.0 12.3 22.51607632 73.50052117
18110 WELD 21,111.9 18110 0.0 12.1 22.51620647 73.49948490
18100 WELD 21,108.8 18100 0.0 3.1 22.51611136 73.49985844
18050 WELD 21,049.7 18050 0.0 12.3 22.51722712 73.49928171
18040 WELD 21,037.3 18040 0.0 12.4 22.51750443 73.49896231
18070 WELD 21,074.4 18070 0.0 12.4 22.51652332 73.50005622
18060 WELD 21,062.0 18060 0.0 12.3 22.51691172 73.49963758
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 64 of 73Criteria:
18510 WELD 21,604.8 18510 0.0 11.7 22.50826072 73.50446105
18500 WELD 21,593.4 18500 0.0 11.4 22.50882342 73.50393046
18530 WELD 21,627.6 18530 0.0 13.2 22.50723475 73.50541120
18520 WELD 21,616.5 18520 0.0 11.1 22.50775192 73.50492949
18470 WELD 21,552.7 18470 0.0 13.9 22.51055451 73.50230982
18460 WELD 21,541.4 18460 0.0 11.3 22.51115075 73.50175466
18490 WELD 21,580.6 18490 0.0 12.8 22.50943397 73.50334617
18480 WELD 21,566.6 18480 0.0 14.0 22.51004470 73.50276608
18550 WELD 21,652.2 18550 0.0 12.0 22.50616970 73.50642215
18540 WELD 21,640.8 18540 0.0 11.4 22.50674264 73.50586505
18570 WELD 21,675.3 18570 0.0 11.2 22.50515061 73.50736249
18560 WELD 21,664.2 18560 0.0 11.0 22.50566947 73.50688708
18450 WELD 21,527.9 18450 0.0 13.5 22.51167713 73.50128528
18350 WELD 21,408.0 18350 0.0 12.7 22.51511686 73.49842480
18340 WELD 21,394.1 18340 0.0 14.0 22.51483847 73.49879262
18370 WELD 21,433.8 18370 0.0 12.6 22.51583575 73.49755191
18360 WELD 21,420.7 18360 0.0 13.1 22.51549530 73.49797149
18310 WELD 21,361.0 18310 0.0 11.2 22.51392110 73.49997165
18300 WELD 21,347.4 18300 0.0 13.6 22.51354098 73.50044359
18330 WELD 21,383.2 18330 0.0 10.9 22.51456094 73.49916035
18320 WELD 21,372.2 18320 0.0 10.9 22.51427605 73.49953513
18420 WELD 21,493.5 18420 0.0 11.7 22.51324114 73.49991274
18410 WELD 21,482.1 18410 0.0 11.4 22.51375336 73.49947151
18440 WELD 21,516.3 18440 0.0 11.6 22.51218572 73.50083966
18430 WELD 21,505.2 18430 0.0 11.1 22.51271827 73.50036909
18380 WELD 21,446.4 18380 0.0 13.3 22.51544962 73.49798485
11000035 WT CHANGE 21,446.3 18380 0.0 0.1 22.51582865 73.49755986 15.90 70000 0.72
18400 WELD 21,470.9 18400 0.0 11.1 22.51427202 73.49902572
18390 WELD 21,459.7 18390 0.0 11.3 22.51487457 73.49848786
18290 WELD 21,333.5 18290 0.0 13.9 22.51318756 73.50089266
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 65 of 73Criteria:
18590 WELD 21,697.9 18590 0.0 11.1 22.50420434 73.50817400
18580 WELD 21,686.5 18580 0.0 11.4 22.50467677 73.50777297
18610 WELD 21,721.6 18610 0.0 13.7 22.50336280 73.50876041
18600 WELD 21,709.0 18600 0.0 12.5 22.50377255 73.50848234
18840 WELD 21,991.0 18840 0.0 11.9 22.50153647 73.50728551
18830 WELD 21,979.7 18830 0.0 11.3 22.50197671 73.50694272
18860 WELD 22,016.7 18860 0.0 11.5 22.50073697 73.50779424
18850 WELD 22,002.9 18850 0.0 13.9 22.50109644 73.50761851
18800 WELD 21,945.8 18800 0.0 11.6 22.50338852 73.50564871
18790 WELD 21,934.7 18790 0.0 11.1 22.50385083 73.50514189
18820 WELD 21,968.8 18820 0.0 10.9 22.50244615 73.50655615
18810 WELD 21,957.4 18810 0.0 11.4 22.50293243 73.50613935
18870 WELD 22,028.3 18870 0.0 10.7 22.50059544 73.50761226
18780 WELD 21,923.2 18780 0.0 11.5 22.50411494 73.50481301
18670 WELD 21,792.0 18670 0.0 11.3 22.50245139 73.50800547
18660 WELD 21,780.9 18660 0.0 11.1 22.50241976 73.50836898
18690 WELD 21,814.6 18690 0.0 11.5 22.50269906 73.50707545
18680 WELD 21,803.4 18680 0.0 11.3 22.50256012 73.50755754
18630 WELD 21,746.4 18630 0.0 11.6 22.50269332 73.50898223
18620 WELD 21,735.3 18620 0.0 11.1 22.50303031 73.50887786
18650 WELD 21,769.6 18650 0.0 11.3 22.50241058 73.50871226
18640 WELD 21,757.9 18640 0.0 11.7 22.50243028 73.50901850
18750 WELD 21,888.8 18750 0.0 11.7 22.50432885 73.50452745
18740 WELD 21,877.9 18740 0.0 10.9 22.50419181 73.50469327
18770 WELD 21,911.9 18770 0.0 11.3 22.50433911 73.50452609
18760 WELD 21,900.4 18760 0.0 11.5 22.50443182 73.50439101
18710 WELD 21,840.2 18710 0.0 14.3 22.50336859 73.50584545
18700 WELD 21,826.1 18700 0.0 14.2 22.50302529 73.50646187
18730 WELD 21,865.7 18730 0.0 12.1 22.50404297 73.50489297
18720 WELD 21,854.5 18720 0.0 11.2 22.50381110 73.50516463
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 66 of 73Criteria:
19170 WELD 22,365.2 19170 0.0 11.1 22.49792875 73.50555782
19160 WELD 22,353.7 19160 0.0 11.4 22.49798131 73.50583302
19130 WELD 22,318.7 19130 0.0 11.7 22.49847823 73.50614513
19120 WELD 22,307.4 19120 0.0 11.3 22.49882008 73.50598909
19150 WELD 22,341.5 19150 0.0 12.2 22.49806224 73.50605508
19140 WELD 22,330.4 19140 0.0 11.1 22.49816541 73.50625560
19110 WELD 22,296.0 19110 0.0 11.4 22.49923482 73.50571129
19000 WELD 22,171.5 19000 0.0 11.6 22.50275972 73.50216029
18990 WELD 22,160.5 18990 0.0 11.0 22.50262813 73.50234346
19020 WELD 22,194.4 19020 0.0 10.9 22.50274701 73.50218560
19010 WELD 22,183.1 19010 0.0 11.3 22.50287592 73.50200818
18960 WELD 22,127.6 18960 0.0 11.7 22.50179732 73.50360852
18950 WELD 22,115.9 18950 0.0 11.7 22.50145975 73.50421266
18980 WELD 22,149.9 18980 0.0 10.6 22.50247915 73.50255113
18970 WELD 22,139.3 18970 0.0 10.7 22.50214375 73.50306273
19080 WELD 22,261.8 19080 0.0 11.1 22.50062062 73.50457146
19070 WELD 22,250.3 19070 0.0 11.5 22.50110524 73.50407980
19100 WELD 22,284.5 19100 0.0 11.5 22.49967701 73.50538700
19090 WELD 22,272.8 19090 0.0 11.7 22.50011738 73.50505108
19040 WELD 22,216.4 19040 0.0 11.5 22.50229901 73.50274136
19030 WELD 22,205.3 19030 0.0 11.1 22.50258017 73.50240338
19060 WELD 22,239.2 19060 0.0 11.1 22.50159419 73.50357559
19050 WELD 22,227.9 19050 0.0 11.3 22.50197106 73.50313100
18920 WELD 22,081.5 18920 0.0 11.7 22.50050175 73.50620006
18910 WELD 22,067.3 18910 0.0 14.2 22.50039511 73.50669198
18940 WELD 22,104.7 18940 0.0 11.2 22.50116138 73.50483038
18930 WELD 22,093.3 18930 0.0 11.5 22.50086516 73.50545747
18880 WELD 22,038.9 18880 0.0 3.9 22.50049921 73.50740490
18900 WELD 22,053.4 18900 0.0 13.9 22.50036104 73.50704789
18890 WELD 22,042.9 18890 0.0 10.6 22.50042713 73.50717909
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 67 of 73Criteria:
19190 WELD 22,388.9 19190 0.0 14.0 22.49802882 73.50478482
19180 WELD 22,376.3 19180 0.0 12.6 22.49796708 73.50518244
19250 WELD 22,462.6 19250 0.0 12.7 22.49982845 73.50104737
19240 WELD 22,448.6 19240 0.0 13.9 22.49947409 73.50164185
19270 WELD 22,486.8 19270 0.0 7.0 22.50065047 73.49980403
19260 WELD 22,475.3 19260 0.0 11.5 22.50027505 73.50035604
19210 WELD 22,414.3 19210 0.0 11.6 22.49853920 73.50351390
19200 WELD 22,402.8 19200 0.0 11.5 22.49825316 73.50419033
19230 WELD 22,437.2 19230 0.0 11.5 22.49915658 73.50225986
19220 WELD 22,425.9 19220 0.0 11.3 22.49883924 73.50289086
19460 WELD 22,699.5 19460 0.0 11.8 22.49690858 73.50348365
19450 WELD 22,688.6 19450 0.0 10.9 22.49740214 73.50306746
19470 WELD 22,711.3 19470 0.0 10.8 22.49646331 73.50383591
19440 WELD 22,676.7 19440 0.0 11.9 22.49791318 73.50257955
19330 WELD 22,550.3 19330 0.0 11.6 22.50157167 73.49851380
19320 WELD 22,539.2 19320 0.0 11.1 22.50150718 73.49858736
19350 WELD 22,572.9 19350 0.0 11.2 22.50142503 73.49871030
19340 WELD 22,561.9 19340 0.0 11.0 22.50161738 73.49846213
19290 WELD 22,505.4 19290 0.0 11.2 22.50100559 73.49925161
19280 WELD 22,493.9 19280 0.0 11.5 22.50089251 73.49946899
19310 WELD 22,527.9 19310 0.0 11.3 22.50142211 73.49868831
19300 WELD 22,516.5 19300 0.0 11.4 22.50122505 73.49895507
19410 WELD 22,642.4 19410 0.0 11.9 22.49945478 73.50102323
19400 WELD 22,630.5 19400 0.0 11.9 22.49990260 73.50053318
19430 WELD 22,665.2 19430 0.0 11.5 22.49840250 73.50210448
19420 WELD 22,654.3 19420 0.0 10.9 22.49893201 73.50157032
19370 WELD 22,596.3 19370 0.0 11.7 22.50098884 73.49925000
19360 WELD 22,584.1 19360 0.0 12.2 22.50121734 73.49896622
19390 WELD 22,619.4 19390 0.0 11.1 22.50031973 73.50005856
19380 WELD 22,608.0 19380 0.0 11.4 22.50072235 73.49959173
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 68 of 73Criteria:
19500 WELD 22,744.6 19500 0.0 11.5 22.49537594 73.50441050
19490 WELD 22,733.7 19490 0.0 10.9 22.49570358 73.50427965
19520 WELD 22,768.1 19520 0.0 11.1 22.49507529 73.50415957
19510 WELD 22,756.1 19510 0.0 12.0 22.49514301 73.50440513
19480 WELD 22,722.2 19480 0.0 11.5 22.49604218 73.50411807
19580 WELD 22,836.4 19580 0.0 11.4 22.49570459 73.50148821
19570 WELD 22,825.0 19570 0.0 11.4 22.49542989 73.50210108
19600 WELD 22,859.4 19600 0.0 11.8 22.49630311 73.50023685
19590 WELD 22,847.8 19590 0.0 11.6 22.49599545 73.50086609
19540 WELD 22,790.8 19540 0.0 11.2 22.49501347 73.50357205
19530 WELD 22,779.2 19530 0.0 11.5 22.49503657 73.50386893
19560 WELD 22,813.6 19560 0.0 11.4 22.49527293 73.50261171
19550 WELD 22,802.0 19550 0.0 11.6 22.49513946 73.50309241
19610 WELD 22,871.2 19610 0.0 13.9 22.49665396 73.49959296
19670 WELD 22,942.3 19670 0.0 11.7 22.49856159 73.49670265
19660 WELD 22,930.7 19660 0.0 11.7 22.49833212 73.49701496
19690 WELD 22,965.2 19690 0.0 11.4 22.49867677 73.49658509
19680 WELD 22,954.1 19680 0.0 11.1 22.49863773 73.49661840
19630 WELD 22,896.5 19630 0.0 11.5 22.49746522 73.49828524
19620 WELD 22,885.1 19620 0.0 11.4 22.49702454 73.49894626
19650 WELD 22,919.2 19650 0.0 11.5 22.49807952 73.49737145
19640 WELD 22,908.0 19640 0.0 11.2 22.49780771 73.49775726
19750 WELD 23,027.9 19750 0.0 10.9 22.49760942 73.49784041
19740 WELD 23,016.5 19740 0.0 11.5 22.49801713 73.49732083
19770 WELD 23,050.3 19770 0.0 11.6 22.49672131 73.49882659
19760 WELD 23,038.8 19760 0.0 11.5 22.49716070 73.49834371
19710 WELD 22,988.2 19710 0.0 11.5 22.49860834 73.49669396
19700 WELD 22,976.6 19700 0.0 11.6 22.49866356 73.49661057
19730 WELD 23,002.5 19730 0.0 14.0 22.49814912 73.49727518
19720 WELD 22,999.7 19720 0.0 2.8 22.49841847 73.49694112
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 69 of 73Criteria:
19840 WELD 23,132.9 19840 0.0 11.6 22.49353988 73.50139173
19830 WELD 23,121.6 19830 0.0 11.3 22.49385414 73.50128331
19860 WELD 23,155.9 19860 0.0 12.3 22.49309252 73.50133607
19850 WELD 23,144.5 19850 0.0 11.4 22.49328377 73.50141359
19800 WELD 23,084.6 19800 0.0 11.4 22.49518472 73.50034285
19790 WELD 23,073.2 19790 0.0 11.3 22.49569101 73.49988181
19820 WELD 23,110.2 19820 0.0 11.4 22.49425092 73.50109570
19810 WELD 23,096.0 19810 0.0 14.2 22.49469280 73.50077311
19920 WELD 23,225.2 19920 0.0 11.4 22.49311209 73.49935642
19910 WELD 23,213.4 19910 0.0 11.8 22.49302046 73.49978814
19940 WELD 23,248.0 19940 0.0 11.6 22.49349909 73.49826599
19930 WELD 23,236.7 19930 0.0 11.4 22.49329527 73.49881711
19880 WELD 23,179.7 19880 0.0 11.7 22.49289651 73.50091890
19870 WELD 23,168.2 19870 0.0 11.5 22.49293730 73.50121016
19900 WELD 23,202.2 19900 0.0 11.2 22.49294701 73.50019534
19890 WELD 23,191.4 19890 0.0 10.9 22.49288446 73.50060331
19780 WELD 23,061.8 19780 0.0 11.4 22.49621579 73.49936058
20000 WELD 23,317.4 20000 0.0 11.4 22.49529681 73.49454662
19990 WELD 23,305.8 19990 0.0 11.5 22.49494662 73.49518761
20020 WELD 23,339.9 20020 0.0 11.3 22.49602995 73.49328778
20010 WELD 23,328.7 20010 0.0 11.2 22.49566291 73.49391127
19960 WELD 23,270.7 19960 0.0 11.5 22.49399835 73.49708841
19950 WELD 23,259.6 19950 0.0 11.1 22.49371888 73.49770344
19980 WELD 23,294.3 19980 0.0 11.5 22.49459604 73.49585319
19970 WELD 23,282.3 19970 0.0 12.1 22.49427466 73.49648921
20070 WELD 23,396.1 20070 0.0 4.1 22.49782578 73.49052706
20040 WELD 23,362.9 20040 0.0 10.9 22.49676048 73.49211965
20030 WELD 23,351.2 20030 0.0 11.7 22.49639340 73.49270031
20060 WELD 23,385.1 20060 0.0 10.9 22.49748508 73.49101640
20050 WELD 23,373.8 20050 0.0 11.4 22.49714461 73.49153011
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 70 of 73Criteria:
20330 WELD 23,696.4 20330 0.0 4.0 22.49391325 73.49453581
20320 WELD 23,685.0 20320 0.0 11.4 22.49443713 73.49400901
20350 WELD 23,711.5 20350 0.0 14.2 22.49314092 73.49519888
20340 WELD 23,700.3 20340 0.0 11.2 22.49337450 73.49505932
20290 WELD 23,645.7 20290 0.0 14.3 22.49630162 73.49196168
20280 WELD 23,631.5 20280 0.0 14.2 22.49677983 73.49144081
20310 WELD 23,673.8 20310 0.0 11.1 22.49506307 73.49333334
20300 WELD 23,660.0 20300 0.0 13.9 22.49570344 73.49263599
20370 WELD 23,739.8 20370 0.0 13.8 22.49197265 73.49633553
20360 WELD 23,725.7 20360 0.0 14.1 22.49261393 73.49569828
20170 WELD 23,500.4 20170 0.0 13.5 22.49959953 73.48807457
20160 WELD 23,488.1 20160 0.0 12.4 22.49955705 73.48811239
20190 WELD 23,524.4 20190 0.0 10.8 22.49950391 73.48825566
20180 WELD 23,513.9 20180 0.0 10.5 22.49960946 73.48808887
20130 WELD 23,453.6 20130 0.0 11.4 22.49911350 73.48864157
20120 WELD 23,442.1 20120 0.0 11.5 22.49888548 73.48893026
20150 WELD 23,476.5 20150 0.0 11.5 22.49943170 73.48825617
20140 WELD 23,464.9 20140 0.0 11.6 22.49928148 73.48843740
20250 WELD 23,594.4 20250 0.0 14.2 22.49808773 73.48995175
20240 WELD 23,583.3 20240 0.0 11.0 22.49848565 73.48946604
20270 WELD 23,619.9 20270 0.0 11.6 22.49722047 73.49095463
20260 WELD 23,608.5 20260 0.0 11.4 22.49771939 73.49036351
20210 WELD 23,547.1 20210 0.0 11.2 22.49925156 73.48855652
20200 WELD 23,535.3 20200 0.0 11.8 22.49938958 73.48839031
20230 WELD 23,569.6 20230 0.0 13.7 22.49877420 73.48912919
20220 WELD 23,558.3 20220 0.0 11.3 22.49902219 73.48883741
20110 WELD 23,430.5 20110 0.0 11.6 22.49863702 73.48924850
20080 WELD 23,400.1 20080 0.0 7.3 22.49814255 73.49007232
20100 WELD 23,418.9 20100 0.0 11.7 22.49836521 73.48960933
20090 WELD 23,407.5 20090 0.0 11.4 22.49820283 73.48988617
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 71 of 73Criteria:
20500 WELD 23,887.2 20500 0.0 11.5 22.48705617 73.49932181
20490 WELD 23,875.2 20490 0.0 12.0 22.48719003 73.49947935
20520 WELD 23,912.8 20520 0.0 11.4 22.48697234 73.49875168
20510 WELD 23,898.7 20510 0.0 14.1 22.48698695 73.49906850
20460 WELD 23,838.3 20460 0.0 11.4 22.48776533 73.49962589
20450 WELD 23,833.8 20450 0.0 4.5 22.48807938 73.49951357
20480 WELD 23,863.7 20480 0.0 11.5 22.48739504 73.49957360
20470 WELD 23,849.7 20470 0.0 14.0 22.48761258 73.49960882
20580 WELD 23,978.8 20580 0.0 11.5 22.48770359 73.49590445
20570 WELD 23,967.3 20570 0.0 11.5 22.48748494 73.49648284
20600 WELD 24,001.5 20600 0.0 11.7 22.48822808 73.49468051
20590 WELD 23,990.2 20590 0.0 11.2 22.48794731 73.49530741
20540 WELD 23,932.8 20540 0.0 11.5 22.48711848 73.49786299
20530 WELD 23,924.2 20530 0.0 8.5 22.48705153 73.49827826
20560 WELD 23,955.7 20560 0.0 11.6 22.48731134 73.49701366
20550 WELD 23,944.3 20550 0.0 11.4 22.48716577 73.49751903
20440 WELD 23,822.4 20440 0.0 11.4 22.48843989 73.49932750
20410 WELD 23,788.6 20410 0.0 11.3 22.48971102 73.49843274
20400 WELD 23,777.2 20400 0.0 11.4 22.49022279 73.49799321
20430 WELD 23,810.9 20430 0.0 11.5 22.48883266 73.49907728
20420 WELD 23,799.9 20420 0.0 11.0 22.48926034 73.49877350
20390 WELD 23,765.1 20390 0.0 12.1 22.49072994 73.49754444
20380 WELD 23,753.6 20380 0.0 11.5 22.49134570 73.49694272
20660 WELD 24,071.0 20660 0.0 11.7 22.49032791 73.49076813
20650 WELD 24,059.6 20650 0.0 11.4 22.48994487 73.49140130
20670 WELD 24,082.7 20670 0.0 11.8 22.49070345 73.49016883
20620 WELD 24,024.9 20620 0.0 11.6 22.48885014 73.49339265
20610 WELD 24,013.2 20610 0.0 11.7 22.48851689 73.49405634
20640 WELD 24,048.1 20640 0.0 11.5 22.48956658 73.49205961
20630 WELD 24,036.5 20630 0.0 11.6 22.48920152 73.49272280
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 72 of 73Criteria:
20820 WELD 24,262.2 20820 0.0 11.7 22.49217774 73.48805775
20810 WELD 24,249.0 20810 0.0 13.2 22.49249979 73.48765774
20840 WELD 24,286.4 20840 0.0 12.4 22.49138105 73.48901278
20830 WELD 24,273.9 20830 0.0 12.5 22.49178834 73.48853998
20780 WELD 24,210.4 20780 0.0 13.8 22.49309259 73.48687076
20770 WELD 24,199.2 20770 0.0 11.1 22.49313815 73.48677256
20800 WELD 24,236.6 20800 0.0 12.5 22.49275362 73.48733248
20790 WELD 24,224.2 20790 0.0 12.4 22.49297630 73.48702085
10000005 Valve (Receiver), SV-6 Halol 24,353.7 20890 5.1 5.4 22.48802000 73.49245000
20890 WELD 24,348.6 20890 0.0 10.5 22.48874788 73.49196343
20900 WELD 24,359.1 20900 0.0 - 0.00000000 0.00000000
20860 WELD 24,311.2 20860 0.0 12.6 22.49040678 73.49013699
20850 WELD 24,298.8 20850 0.0 12.4 22.49090391 73.48956729
20880 WELD 24,336.2 20880 0.0 12.5 22.48932248 73.49134697
20870 WELD 24,323.7 20870 0.0 12.4 22.48987977 73.49072975
20760 WELD 24,185.8 20760 0.0 13.4 22.49312562 73.48677620
20680 WELD 24,094.5 20680 0.0 11.3 22.49108798 73.48957919
20740 WELD 24,163.3 20740 0.0 11.2 22.49285024 73.48711475
20730 WELD 24,151.7 20730 0.0 11.6 22.49263191 73.48739587
20750 WELD 24,174.5 20750 0.0 11.4 22.49303091 73.48688920
11000036 WT CHANGE 24,174.4 20750 0.0 0.0 22.49285625 73.48710724 23.80 70000 0.72
20700 WELD 24,117.2 20700 0.0 11.7 22.49179027 73.48855018
20690 WELD 24,105.8 20690 0.0 11.4 22.49145825 73.48903370
20720 WELD 24,140.1 20720 0.0 11.6 22.49239005 73.48772129
20710 WELD 24,128.9 20710 0.0 11.2 22.49209692 73.48811892
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
Pipeline Listing ReportGas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Page 73 of 73Criteria:
12000001 End Run Tickle 24,365.3 20900 6.2 - 0.00000000 0.00000000
LOCATIONS 6
GROUPED PITS 0
WT CHANGES 37
MISC 2
GAINS 0
WELDS 2080
DEFORMATION 0
Type Number
ID# DescriptionDistance
(m) Joint #
U/S Weld Dist.
D/S Weld Dist. Latitude Longitude
Orientation(Deg / O’Clock)
Depth (%)
Length or Pipe
ThicknessWidth or
SMYS
Failure Pressure or Safety
FactorPfail/
MAOP
TDW Services, Inc.
Gas Authority of India Ltd.
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
General Inline Inspection TermsGLOSSARY
BURSTPRESSURE
The pressure at which the nominal hoop stress in the wall of a pipe equals the specified minimum yield stress of the pipe grade. It is calculated by 2st/D where s = SMYS, t = nominal wall thickness, D = nominal outside diameter of pipe.
CALIBRATIONDIG An exploratory excavation to compare findings of an in-line inspection system to actual conditions with the purpose of improving data analysis.
BORE RESTRICTION Any reduction of the cross-section of the pipe that may restrict the passage of an ILI pig.
BUCKLE A condition where the pipeline has undergone sufficient plastic deformation to cause permanent wrinkling or deformation of the pipe wall or the pipe's cross section.
CASING ANOMALY When the casing is not welded, or when a gap occurs in the weld, this signature is detected by the tool, and identified with a miscellaneous remark.
CLAMP Non-welded full encirclement pipeline feature not located at a bridge or water crossing, in some cases a type of temporary repair.
COMPONENT Any physical part of the pipeline , other than line pipe, including but not limited to valves, welds, tees, flanges, fitting, taps, branch connections, outlets, supports and anchors.
CHARACTERIZATION The process of quantifying the size, shape, orientation, and location of an anomaly, defect, or critical defect after it has been detected.
CHECK VALVE A valve that prevents reverse flow.
ACCELERO-METERS Part of the INS package of the in-line inspection tool. Each TDW tool contains 3 axis-aligned accelerometers measuring orientation and shock.
ANCHOR,WEIGHT OR
HANGAR
Non-welded full encirclement pipeline features typically evenly spaced across water crossings. These are usually not detrimental unless associated metal loss is detected.
AGM (Aboveground Marker)
A portable device placed at an above ground reference point that both detects and records the passage of an in-line inspection tool. AGMs are typically reported using a marker number followed by the aboveground reference point description of the location device (box) placement.
ABOVE-GROUND REFERENCE POINTS
The above ground reference point is a permanent reference on or above the pipeline, which can be used to locate features in the pipeline. Reference points can be valves, fences, test stations, markers posts, or ther permanent features.
ANOMALY Any kind of imperfection or defect that may be present in the wall of the pipe. This includes coating or welding.
BEND A physical pipe configuration that changes pipeline direction.
BEND RADIUS The radius of the bend in the pipe as related to the pipe diameter (D). Example: A 3-D bend would have a radius of 3 times the diameter of the pipe measured to the centerline of the pipe.
APPURTENANCE A component that is attached to the pipeline; e.g., valve, tee, casing, instrument connection.
ASME B31G, MODIFIED ASME B31G, or
DNV RP-F101
Commonly used analysis criterion for metal loss anomalies in a pipeline. TDW software may use ASME B31G, MODIFIED ASME B31G, or DNV RP-F101 to calculate the safe maximum allowable operating pressure or failure pressure at an area of metal loss. These formulas utilize only length and depth - they do not take into consideration the width of the anomaly. The MODIFIED ASME B31G more closely approximates the values obtained via the RSTRENG calculations, which is less conservative than the standard ASME B31G calculation. See also DNV RP-F101.
General Inline Inspection T
erms
TDW Services, Inc.
Gas Authority of India Ltd.
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
General Inline Inspection Terms
Page 2 of 7
DOT192 Part 192 of the Code for Federal Regulations (CFR) Title 49 that addresses Gas Transmission Pipelines.
DOT195 Part 195 of the Code for Federal Regulations (CFR) Title 49 that addresses Transportation of Hazardous Liquids by Pipeline.
DENTS Dents are depressions in the pipeline that may be detected by the inline inspection tool. MFL tools may be able to detect dents, but may not be able to accurately size them.
DETECTIONTHRESHOLD A characteristic dimension or dimensions of an anomaly that must be exceeded to achieve a stated probability of detection.
ERW (Electric-Resistance Weld)
Describes a process used to form steel from a sheet into tubular form (pipe). Welds are formed by resistance heating of two edges of a metal sheet and then forcing them together to create a solid-state weld.
EXPANSION Local increase of pipe diameter during service which indicates the yield stress of the pipe at that location has been surpassed.
ECCENTRICCASINGS
TDW tools detect when a casing is not centered on the pipeline. These casings are referred to as being eccentric. The closer the casing is to the pipeline, the stronger the signal seen by the inspection tool. The tool may not detect if the casing is shorted to the pipe wall. The tool might see evidence of a short, such as metal loss.
ESTIMATED REPAIRFACTOR (ERF) The ratio of pipeline design pressure or in some cases MOP to the safe maximum operating pressure (P’).
CORROSION(Internal)
Metal loss due to chemical or other attack on the steel from liquids on the inside of the pipe. Electrochemical attack can also occur in local cells, but this is less frequent.
DATA ANALYSIS The process through which indications are evaluated to classify, characterize and size them as non-relevant conditions, pipeline components, anomalies, imperfections, or defects.
CONTROL POINT Control points are know locations used to provide coordinate updates to aid the final processing of the inertial data gathered from the instruments onboard the inspection vehicle.
CORROSION(External)
Metal loss due to electrochemical, galvanic, microbiological, or other attack on the pipe due to environmental conditions surrounding the pipe.
DEFECT An anomaly for which an analysis, such as ASME B31G, would indicate that the pipe is approaching failure as the nominal hoop stress approaches the specified minimum yield stress (SMYS).
DEFORMATIONPIG
A pig designed to record conditions such as dents, wrinkles, ovalities, bend radius and angle by making measurements of the inside surface of the pipeline.
DATUM
A datum is a set of reference points on the earth's surface against which position measurements are made. Horizontal datums are used for describing a point on the earth's surface, in latitude and longitude or another coordinate system. While hundreds of reference datums exists some examples of horizontal datums include, NAD27, NAD83, and WGS84. Vertical datums are tidal, based on sea levels referencing geodetic datums such as NAVD88, or geodetic, based on the same ellipsoid models of the earth used for computing horizontal datums.
DNV RP-F101 An analysis procedure that differs from the commonly used ASME B31G criterion. Developed by the Norwegian company Det Norske Veritas, this method is employed for European and Asian pipelines. The DNV algorithm is generally considered to be more conservative than ASME B31G.
GLOSSARY PART 2
General Inline Inspection T
erms
TDW Services, Inc.
Gas Authority of India Ltd.
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
General Inline Inspection Terms
Page 3 of 7
GLOSSARY PART 3
HALL SENSORS A sensor that directly measures the remaining magnetic field strength not absorbed by the pipe.
HCA (HighConsequence
Area)
A criterion for pipelines designed by the Code of Federal Regulations which define what program and practices operators must use to manage pipeline integrity if the pipeline is located near a commercially navigable waterway, a high population area, or an unusually sensitive area.
GROUPA group is several pits that are grouped together using specific interaction rules. If a pit is a mountain peak, then a group is a mountain range. The reason for groups is so that the overall extent of the metal loss area can be evaluated. Most formulas for calculating the strength of the pipe wall around metal loss look at the overall length of metal loss after interaction rules have been applied to pits.
HALF SOLE A device used to repair a pipeline by welding a small section over half the circumference of the pipe over the defect, literally half of a sleeve.
HIGHRESOLUTION
A term used to describe the function of TDW tools for use in MFL or Deformation analysis schemes. Both MFL and Deformation tools are considered high resolution.
IMPERFECTION An anomaly with dimension and characteristics that do not exceed acceptable limits.
HEAT AFFECTEDZONE (HAZ) The region around a weld which has been metallurgically affected during the welding process.
HEAVYWELD
A girth weld in which the root pass or a portion of the root pass intrudes further than normal into the ID of the pipe. Not usually considered detrimental.
GYROSCOPES(Gyros)
Electronic sensors used to measure change in direction of in-line inspection tool during inspection process. Displayed as pitch and yaw in PIGTRAP.
FITTING A branch connection attached to the pipeline which is smaller than the nominal pipe size that alters flow or diverts product (e.g. tap, offtake, split-tee, weld-o-let, thread-o-let).
GAIN (Metal inClose Proximity)
The inspection tool may detect ferrous metal objects located close to or touching the pipeline. They appear as additional metal added to the pipe and are referred to as gains. Clamps or anchors are considered gains as well as features such as puddle welds or CP connections. Generally, repairs such as patches or sleeves are called out as repairs even though they show appear in the data as gains.
FAILUREPRESSURE
RATIO (FPR)The ratio of the predicted failure pressure calculated by an analysis criterion (e.g. ASME B31G, RSTRENG, etc.) to the MAOP
FEATURE Any physical object detected by an in-line inspection system. Features may be anomalies, components, or some other item.
GOUGE Elongated grooves or cavities caused by mechanical removal of metal.
GPS (GlobalPositioning
System)
The navigational system utilizing satellite technology to provide a user an exact position on the earth's surface. When coupled with known surface locations such as valves and AGMs, an ILI tool’s INS or IMU can approximate or calculate the centerline of a pipeline.
GIRTH WELD A circumferential weld joining two joints of pipe.
GIS Geographic Information System is any system that captures, stores, analyzes, manages, and presents data that are linked to location. GIS is the merging of cartography and database technology.
General Inline Inspection T
erms
TDW Services, Inc.
Gas Authority of India Ltd.
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
General Inline Inspection Terms
Page 4 of 7
MAOP (MaximumAllowableOperatingPressure)
(or Design Pressure) The maximum internal pressure permitted in the operation of a pipeline as defined by the Code of Federal Regulations.
MAPPING PIG An ILI tool that uses an IMU to collect data that can be analyzed to produce an elevation and plan view of the pipeline route.
LOCATIONA location is a feature in the pipeline that can be used to correlate the inspection tool data to above ground references. Common location features include valves, fitting, flanges, tees, casings, repairs and AGMs. For example, a metal loss area could be referenced as being 200 feet downstream from a valve. Not all locations can be easily found from aboveground.
LATITUDE &LONGITUDE
Latitude is the angular distance north or south from the earth's equator measured through 90 degrees. Longitude is the arc or portion of the earth's equator intersected between the meridian of a given place and the prime meridian and is expressed either in degrees or in time. Latitude and longitude are reported as GPS coordinates. Predicted GPS for features are provided in the Pipeline Listing section.
METAL LOSS Any of a number of types of anomalies in pipe in which metal has been removed from the pipe surface, usually due to corrosion or gouging.
MFL (MagneticFlux Leakage)
An inspection technique in which a magnetic field is applied to a pipe section and measurements are taken of a magnetic flux density at the pipe surface. Changes in measured flux density indicate the presence of a possible defect.
MEASUREMENTTHRESHOLD A characteristic's dimension or dimensions above which anomaly measurements can be made.
MECHANICALDAMAGE
A generic term used to describe combinations of dents gouges, and/or cold work caused by the application of external force. Damage includes coating, movement of metal and high residual stress.
LAUNCHER Refers to the beginning of the inspection; an oversize section of pipe equipped with sealing door through which the inspection tool is loaded into the pipeline.
INDICATION Any measured signal or response from an inspection of a pipe different than the normal baseline signal.
INS (Inertial Navigation
System)Refers to a system of accelerometers and gyroscopes to track the movement and orientation of the inspection tool through bends, turns, etc.
IMU (InertialMeasurement Unit)
Inertial measurement unit, or IMU, is the main component of inertial guidance systems. An IMU works by sensing motion including the type, rate, and direction of that motion using a combination of accelerometers and gyroscopes.
INCLUSION An anomaly in the cross section of the pipeline caused by manufacturing processes. Inclusions may be detrimental if they protrude through the pipe wall. Refer to mill anomaly.
JOINT A single section of pipe that is welded to others to make up a pipeline.
LACK OF FUSION(LOF) In a weld, any area or zone that lacks complete melting and coalescence of a portion of the weld.
INTERACTIONRULES
Specifications that establish spacing criteria between anomalies or defects (pits). If the indications or defects are proximate to one another within the criteria , the anomaly or defect is treated as a single larger unit or group for engineering analysis purposes.
INSPECTION The use of a non-destructive inspection technique.
GLOSSARY PART 4
General Inline Inspection T
erms
TDW Services, Inc.
Gas Authority of India Ltd.
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
General Inline Inspection Terms
Page 5 of 7
GLOSSARY PART 5
Pfail (Calculatedfailure
pressure)
Calculated maximum operating pressure for the pipeline segment as calculated based on information provided by the Customer. TDW software uses ASME B31G, MODIFIED ASME B31G, or DNV RP-F101 to calculate the failure pressure (Pfail) of the pipeline at a metal loss area for gas lines. The calculation also takes into consideration a temperature factor, for use when the line is at elevated temperature, and a safety factor. The default values used in calculations are a temperature factor of 1, and a safety factor of 100%.
P' (Calculatedsafe maximum
operatingpressure)
Calculated safe maximum operating pressure for the pipeline segment as calculated based on information provided by the Customer. TDW software uses ASME B31G, MODIFIED ASME B31G, or DNV RP-F101 to calculate the safe maximum allowable operating pressure (P') of the pipeline at a metal loss area for liquid lines. The calculation also takes into consideration a temperature factor, for use when the line is at elevated temperature, and a safety factor. The default values used in calculations are a temperature factor of 1, and a safety factor of 72% (80% for Canada).
P
Calculated pressure rating for the pipe. Per ASME B31G, it is the greater of either the established MOP for liquid lines (MAOP for gas lines), or 2stFT/D, where S = SMYS, F = appropriate design factor from ASME B31G, T = Temperature derating factor, D = nominal outside diameter of pipe, and t = nominal wall thickness. See ASME B31G. In application, this variable is identical per DNV RP-F101, however it is calculated using different formulas and factors.
P'/PPercent of maximum established pressure, this is calculated by dividing the calculated safe pressure of the defect (P') by the current established maximum operating pressure of the pipeline (P). For TDW reporting, P is either established MOP provided by the customer or the calculated pressure rating for the pipe (P). Percentages less than 100% are considered pressure-reducing.
PIG A generic term signifying any independent, self-contained device, tool or vehicle that moves through the interior of the pipeline for purposes of inspecting, batching, dimensioning, or cleaning.
PATCH A device used to repair a pipeline by welding a small section of pipe on top of the defect.
Pfail/MAOP Percent of MAOP, this is calculated by dividing the calculated failure pressure of the defect (Pfail) by the current MAOP of the pipeline (P). For TDW reporting, P is either established MAOP provided by the customer or the calculated pressure rating for the pipe (P).
MISALIGNMENT A girth weld anomaly where the two joints of pipe were not aligned properly prior to welding. Sometimes referred to as a hi-lo.
MINIMUMBORE The minimum measured Internal Diameter of the pipe at any particular point. Also referred to as minimum cross-section.
MILLANOMALY
The process of manufacturing pipe can often leave indications in the pipe wall. Typically these anomalies are not detrimental, and are identified for the benefit of the client.
MOP (MaximumOperatingPressure)
The establishhed maximum internal pressure expected during the operation of a pipeline, which cannot normally exceed the maximum allowable operating pressure (MAOP).
OVALITY A condition in which a circular pipe forms into an ellipse, usually as the result of external forces.
ORIENTATION The location of the reference around the circumference of the pipe, as viewed in the direction of flow (downstream). The value is represented in degrees 0-360° rotating clockwise around pipe. (0° = top of pipe, 90° = 3:00)
ODOMETER Wheels on in-line inspection tool, which rotate along the pipe to measure the distance the tool has traveled.
General Inline Inspection T
erms
TDW Services, Inc.
Gas Authority of India Ltd.
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
General Inline Inspection Terms
Page 6 of 7
GLOSSARY PART 6
SAFETY FACTOR
(or Design Factor) Typically 0.72 for liquid lines per ASME B31G (0.80 in Canada) . In setting the safety factor, due consideration has been given to and allowances made for the manufacturing tolerance and maximum allowable depth of imperfections provided for in the specifications.DNV RP-F101 uses a slightly different Total Usage Factor, which is entered as the Safety Factor in PIGTRAP. The typical 0.72 factor becomes 0.648 when applying the DNV modeling factor of 0.9.
SEAMLESS Pipe that is manufactured by means of extrusion. This process typically creates significantly more variation in pipe wall thickess than ERW pipe.
RESIDUAL DENTDEPTH
The dent depth measured under a particular set of conditions, e.g., in pressurized or un-pressurized pipeline. While maximum dent depth does not change, the residual or measured dent depth changes with pressure and loading. Also referred to as the measured dent depth.
RUPTUREPRESSURE
RATIO (RPR)
The ratio of the predicted failure pressure calculated by an analysis criterion (e.g. ASME B31G, RSTRENG, etc.) to the pressure at specified minimum yield strength (SMYS)
SMFL (Spiral Magnetic Flux Leakage)
A type of MFL tool that creates an oblique, near 45 degree magnetic field within the pipe wall. This allows detection and characterization of long and narrow metal loss or seam features on par with a TFI tool.
SPACER A device used to maintain space between a casing and a pipeline.
SEAM WELD(or SEAM)
The longitudinal or spirally-oriented weld in pipe connecting two edges of a formed plate which was created at the pipe mill.
SLEEVE A device used to repair a pipeline by welding a small section of pipe over the full circumference of the pipe over the top of the defect.
PITLocalized concentrated-cell corrosion on the external or internal surfaces that results from generation of a potential (voltage) difference set up by variations in oxygen concentrations within and outside the pit. The oxygen-starved pit acts as anode and the pipe surface acts as the cathode. If several pits are in close proximity to each other, they may be grouped together using interattion rules as one group.
PLANAR An NDT term indicating a feature has two-dimensional characteristics like a fissure. Sometimes referred to as crack-like.
PIGTRAP Pipeline Inspection Graphical Test Reporting and Analysis Program (PIGTRAP). Proprietary software developed by TDW Inc. for viewing data collected by the inspection tool.
PIPE SUPPORT Any device used to support an aboveground pipeline.
RECEIVER Refers to the ending of the inspection; an oversize section of pipe equipped with sealing door through which the inspection tool is retrieved from the pipeline.
REPORTINGTHRESHOLD
A parameter that defines whether or not an anomaly will be reported. The parameter may be a limiting value on the depth, width, or length of the anomaly or feature.
RSTRENG A computer program designed to calculate the calculated safe maximum operating pressure (P') of corroded pipe. RSTRENG results are approximated when Modified B31G criteria is used.
REBOUNDING The process of changing the dent depth and shape by internal pressure in the pipe. Generally, dents due to third-party contact will re-round, while dents due to rocks will not unless the rock causing the dent is removed.
General Inline Inspection T
erms
TDW Services, Inc.
Gas Authority of India Ltd.
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
General Inline Inspection Terms
Page 7 of 7
GLOSSARY PART 7
VOLUMETRIC A term indicating a feature has three-dimensional characteristic similar to a typical corrosion pit.
TRAP Pipeline facility for launching and receiving tools and pigs.
WELD ANOMALY Any area or zone in a weld that lacks complete melting and fusion of a portion of the weld which could have occurred during the welding process or caused by corrosion.
WRINKLE BEND A field bend that contains smooth and localized bulges on the inner radius of the bend, sometimes formed when pipe is cold bent.
WRINKLE A smooth and localized bulge visible on the outside wall of the pipe.
STITCHING Intermittent or repeating lack of fusion in a seam weld.
SMYS (SpecifiedMinimum Yield
Strength
A required strength level that measured yield stress of a pipe material must exceed, which is reported as pipe grade. The measured yield stress is the tensile stress required to produce a total elongation of 0.5 percent of a gage length as determined by an extensometer during a tensile test.
TEMPERATUREFACTOR Typically 1.0 unless the metal temperature is expected to exceed a normal temperature range of -20°F (-30°C) to 250°F (120°C).
TRACKING The process used to monitor the progress of the inspection tool through the pipeline. AGM boxes are placed at aboveground marker reference locations to record the passage of the inspection tool.
THIRD PARTYDAMAGE Damage to a pipeline system by an outside party. See mechanical damage.
General Inline Inspection T
erms
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Appendix A
Page 1 of 1
4. For dig sheet creation, please refer to Appendix C.
5. TDW inspection tools are designed to detect various features and anomalies within a pipeline. These various features and anomalies are added to the database using PigTrap™ software by qualified Data Analysts.
6. Database Numbering System: All entries in the database have a unique number assigned to them. The table below lists the number range of each category of database records.
1. The Graphs, Dig Sheets, and Tables used in this report were generated using a standalone reporting engine from data contained in a Microsoft Access™ database.
2. If the end user has Microsoft™Access on their computer, they have complete access to the inspection database. The database file which has an extension of *.mdb (Microsoft™ database) is stored in the same directory as the tool data. Although the printed reports and report spreadsheet were generated by a standalone reporting engine, using Access the user can customize some basic graphs or tables contained in the database. Alternatively, the data can be exported to a spreadsheet if preferred.
3. The PigTrap™ software, included with this report, provides the user with an easy way to view the data collected by the TDW in-line inspection tool and can also be helpful when trying to locate certain features or specific sections of pipe. The software can be run off various media or installed onto a network or hard drive. Please refer to Appendix B for installation requirements and instructions.
Pits or Other Defects 20,000,000 to 39,999,999
Bore Restrictions 15,000,000 to 15,999,999
Deformations 14,000,000 to 14,999,999
Groups (of Pits) 40,000,000 to 49,999,999
8. All other records are incremented by 1 from one record to the next. For example, the first Location record would be numbered 10,000,000, the second record would be 10,000,001, and the third record would be 10,000,002, etc. Depending on information sent out previous to the final report, numbering may change during analysis of the run.
Seam Welds 51,000,000 to 51,999,999
Welds 110 to 9,999,999
7. All records are numbered sequentially from the beginning of the pipeline section to the end of the pipeline section. By default Welds begin at 110 and are incremented by 10 from one weld to the next. This can be altered to match customer weld or joint numbering by request.
Locations 10,000,000 to 10,999,999
Gains 13,000,000 to 13,999,999
Misc 12,000,000 to 12,999,999
Pipe 11,000,000 to 11,999,999
Database and Reporting Details
Appendix A
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Appendix B
2. Access the Setup.exe program located on the CD or DVD. This can be done by browsing to your computer’s CD/DVD drive and double clicking Setup.exe. This will launch the Data Installer program.
3. Click Next to continue installing the run data.
Note: If you want to install only the Pigtrap™ software and not the run data (advanced users only), choose Cancel and go to the Pigtrap™ Installation steps on page 3.
The inspection report will be accompanied by either CDs, DVDs, or an external drive containing all files necessary for installation. Installation for CDs and DVDs differs from external drives, if an external drive accompanied your final report please skip to PigTrap™ Installation.
Run Data and PigTrap™ Installation
1. Insert Disk 1 from the report binder into your computer’s CD/DVD drive.
CDs and DVDs
• Microsoft® Report Viewer 2008 SP1• Microsoft® Visual C++ 2008 SP1 Redistributable Package (x86)
• Microsoft® Access 2003 or higher• Microsoft® .NET Framework 3.5 Service pack 1
What electronic data accompanied the inspection report
• Spreadsheet – .XLS (Microsoft Excel) A Pipeline Listing is generated for your run in an Excel spreadsheet format. Each event at a particular location is identified and described. You may use Copy and Paste techniques to build your own custom formatted report.
• Setup.exe file – This file executes the installation of the data for the specific run contained on the disk(s) or external drive.
• .rsf – This is a PigTrap™ reference file which holds specific settings for the run to be viewed.
The CD, DVD, or external drive supplied by T.D. Williamson, Inc. for this PigTrap™ inspection of your pipeline contains the following types of files. For CD or DVDs the first disk will contain these files while accompanying disks (if any) contain raw tool data only. External drives will contain this information in the Final Report folder on the external drive under the run name folder.
• Database – .MBD (Microsoft Data Base) Files of this type may be viewed through Microsoft Access. This file contains the analysis of the inspection.
Before you install and run PigTrap™ please verify that the computer you are installing to meets the minimum requirements needed to successfully open and operate PigTrap™.
Windows OS
System Requirements
The PigTrap™ software allows the user to view all of the data collected during the Magpie/TDW inline inspection survey. Installation requires the disk(s) or external drive that accompany the inspection report.
• Microsoft® Windows 7, Vista®; Windows® XP Professional, Home Edition
• 1 GB available hard drive space plus additional necessary for the run size.• Qualified hardware-accelerated OpenGL graphics card, 32-bit color, and 256MB of
VRAM (latest manufacturer drivers strongly recommended also).
• 2 GB RAM or more
o Administrator rights required• 2.0 GHz Intel® Core™ 2 Duo Processor or higher
• h*.nnn, c*.nnn, i*.nnn, p*.nnn, t*.nnn, l*.nnn & o*.nnn – The raw tool data created on-board the inspection tool. These files are necessary for PigTrap™ to function properly. CD and DVDs have the option to install these files onto your computer, if chosen not to install them to your computer the disks must be used to view the run.
Installation Instructions for PigTrap™ Pipeline Inspection Graphical Test/Report Analysis Program
Appendix B
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Appendix B
Page 2 of 8
9. Click Done to complete the run data installation.
10. After clicking Done in the Data Installer PigTrap™ Installation will automatically launch.
7. The following progress bar will appear. There may be a short delay while the database is being copied. Be patient, this is normal.
8. You may be prompted to insert other disks from the run distribution if data was supplied on more than one disk. Insert the required disk and click OK to continue. Repeat until all disks have been copied.
6. If the installation folder does not already exist, then you will be prompted to create it. Click Yes to create the new folder.
4. Choose the type of install you would like to perform: Full Install (recommended) or Minimal Install. The size of the installation is shown next to each type of installation. The database file must be installed for PigTrap™ to operate properly, but you may choose to not install the raw data. If you choose to not install all the data, you may need to change disks while viewing the data in PigTrap™. Click Next to continue after making your choice.
5. Choose the installation location on your computer for the data files. The default and recommended location is C:\Magpie\Software. The location inside this folder is based on the trap date, name, and size of the run. If you would like to specify another location, click the Browse... button. Click Finish to continue.
Appendix B
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Appendix B
Page 3 of 8
3. PigTrap™ Setup Wizard will launch. This will guide you through the installation of PigTrap™. Click Next to continue.
4. The Software License Agreement will appear. Read the agreement select I Agree to continue. You must accept the agreement to install PigTrap™.
Note: CD and DVDs follow a slightly different installation process. Steps 1 and 2 are for external drives, if you are installing from CDs or DVDs please skip to step 3.
PigTrap™ Installation
2. Access the PigTrap™ setup.exe located on the external drive. This can be done by browsing to external drive and double clicking PigTrap™ setup.exe.
1. Plug the external drive into your computer.
7. When prompted whether you would like to view the run data, click Yes to launch PigTrap™. Shortcuts are now on the desktop to the run and to PigTrap™. Once PigTrap™ opens with the data, choose save in the upper left of the data view.
5. Choose the installation location on your computer for the PigTrap™ software. The default and recommended location is C:\Magpie\Software. Click Install to continue.
6. The following progress bar will appear while PigTrap™ installs all the necessary files. Once the installation has completed click Finish to close the wizard.
Appendix B
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Appendix B
Page 4 of 8
We packed so much into the new PigTrap™ the older reference files just couldn’t hold it all so a new one may need to be created. Once the new reference file finishes, you will be able to freely navigate around in PigTrap™.
The data viewed in PigTrap™ is a 360 degree snapshot of the inside of the inspected pipe. This captured data is sliced down the middle and laid flat in the PigTrap™ main display. The horizontal lines represent sensor data collected from the pigging tool. Each line is one sensor. The left side of the screen is ''upstream'' while the right side of the screen is ''downstream''. So, as you scroll from left to right you are moving downstream from the launch valve.
What am I looking at?
1. Double click on PigTrap™ .exe icon. Click on the Open Folder icon , then browse to the installed inspection data folder and select the desired .rsf or .mrsf file.
Viewing the inspection data in PigTrap™ can be done by using one of three different methods.
Opening and Viewing the Inspection Data
PigTrap™ was designed so you would have the ability to review previous TDW/Magpie inspection data when needed. However, you may need to acquire an updated Microsoft Access Data-base from one of our TDW representatives. When opening previous data in PigTrap™ you may encounter the message, ''Your database is very old. You may need to update it.'' If this happens, don't panic. Chances are you will be able to view the data without any problems. If you can't, just contact your TDW representative and we can send you a newer database and walk you through the process of updating.
3. Drag and drop a run settings file (.rsf or .mrsf) on top of the PigTrap™ .exe file.
2. Double click on a run settings file (.rsf or .mrsf) that is associated with PigTrap™.
For additional information regarding dig/feature sheet creation, see Appendix C.
For example: Launch and Receive Valves can be found under ''location'' button, you’ll also find Bends, Tees, Markers, etc.
An interactive training is also available from the Help menu . This provides de-tailed information about PigTrap™ and its features. Please contact your TDW representative if you would like some additional training.
Training
Click on the binoculars to open the Database/Search Edit (DSE). This displays a table of the pipe objects marked by the Data Analysis personnel. The buttons in the DSE allow for a high level filtering of specific types of marked pipe objects in the table. Right click on any pipe object to display a context menu of filtering, resize columns/rows and generate dig/feature sheets.
The horizontal scrollbar at the bottom of the main view moves the view upstream or downstream. Clicking on the left arrow moves upstream while clicking on the right arrow moves downstream.
Basic Navigation
Select the ''Jump to Distance'' icon from the run toolbar to enter a desired distance point to navigate in the inspection data. The option ''View Width'' sets how much viewable area to display (time based).
Zooming IN/OUT on the data is easily performed by clicking on the Zoom buttons.
The vertical scrollbar at the right side of the main view rolls the data vertically to a desired orientation of the view.
Appendix B
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Appendix B
Page 5 of 8
Sensors are not enabled. Turn on the sensors from the Run Toolbar.
Can't see the sensor data.Zoomed in very close. Click on the Zoom OUT button.
REF error message.If this is the first time opening a run with PigTrap™ , it may attempt to create a reference file (.ref2). This message appears because a .ref2 file does not exist or it is corrupt.
Select OK to create a new ref2 file.
Can't find the Status/Database Window.
The Status/Database windows are not enabled Go to View>Status Window and toggle the option ON
Microsoft Visual C++2010 redistributable is corrupt or not installed.
This is typically installed the TDW Inspection data. It is possible to have a corrupt install and additional help may be required to correct the issue. Please contact your local IT department to assist with the prerequisite install.
Crashes while opening. The .rsf is corrupt and needs replacing. Reinstall the inspection data.
The video card drivers are out of date.Update the graphic card drivers. Note: Before installing the latest driver, you may need to uninstall the current drivers while in Windows safe mode. Can also turn off shaders.
''Data files missing'' message displayed on the Main view.
PigTrap™ is not able to load the necessary data file(s) because they are missing, not installed correctly, media/hardware damage (Dirty or scratched CD/DVD, drive failure).
Please reinstall the inspection data, check the run setting has the correct path to the files (Run Settings>Files>Data File Directory), clean the CD/DVD.
Issue Possible Cause Possible Solution
Trouble Shooting
''Generate Dig Sheet'' is not available from the DSE.
PigTrap™ is not installed correctly. Please reinstall PigTrap™.
One of the task specific modes is enabled. Press the ''Done'' or ''Cancel'' buttons from the bottom left.
Not able to highlight pipe objects.The color bit depth is not set correctly. PigTrap™ requires a 32 bit color depth, please contact IT to assist
in changing to the correct setting.
Main window title bar is not visible. Full screen is enabled. Press ''F11'' on the keyboard.
Appendix B
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Appendix B
Page 6 of 8
Toolbar Layout and Functions
Appendix B
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Appendix B
Page 7 of 8
PigTrap™ for MFL Runs
Appendix B
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Appendix B
Page 8 of 8
PigTrap™ DEF Runs
Appendix B
Gas Authority of India Ltd. - K360HD 48" IP-2, Sherpura to SV-6, Halol
Gas Authority of India Ltd.
TDW Services, Inc.
Appendix C
Page 1 of 1
a. This will bring up the Database Search/Edit (DSE) window.
3. You can choose what type of feature you want to list in the window by clicking on the icon in the margin.
1. Open PigTrap™ to view the inspection data for the run. Please consult Appendix B if you need instructions on installing and viewing the raw data.
2. Click on the Database Search/Edit option either by clicking on the small binoculars icon in the toolbar or choosing the option under the Seek toolbar.
b. Generate Dig Sheet From Table – This will create a separate dig sheet for every item in the list whether highlighted or not. Note that if the list contains a lot of features, this could lead to numerous dig sheets being created and may impact the short term performance of your computer while they are being generated.
a. Generate Dig Sheet From Selection – This will create a separate dig sheet for each of the highlighted rows in the list. Using the Ctrl key or the Shift key and clicking rows will allow for multiple row selection.
6. The dig sheets you requested will automatically be previewed for easier printing as well as saved to a directory as a pdf file for printing later.
7. Also under the Dig Sheets toolbar in the DSE window, you may change various dig sheet formatting preferences by clicking on Dig Sheet Settings option.
a. To choose which directory the dig sheets are saved into, choose Report Creation Settings under the Dig Sheets option in the top toolbar.
a. Clicking on the header of the column will sort either ascending or descending. Click again to reverse the order.
4. Once the list populates with that type of object, you can filter or sort the data to find the object(s) for which you want to create dig sheets.
b. You may also use or create various filters by clicking on one of the two Filters buttons.
5. Right clicking in the table or choosing the Dig Sheets option in the top toolbar will allow you to create dig sheets one of two ways:
c. There is also a Displayed Columns button which allows you to hide or show the various columns of data.
The user can view and print dig sheets for any anomaly or feature detected in the pipeline including Metal Loss (Groups or Pits), Dents, Locations, Gains, Wall Thickness changes, Welds, Miscellaneous notes, etc.
Printing Dig Sheet Reports Instructions
Appendix C