Download - 2006trans13_b
7/28/2019 2006trans13_b
http://slidepdf.com/reader/full/2006trans13b 1/10
2006trans13_b .doc
SENSED
PARAMETER FAULT
CODE
ACCEPTABLE
OPERATING
RANGE AND
RATIONALITY
PRIMARY MALF
DETECTION
PARAMETERS
SECONDARY PARAMETERS
AND CONDITIONS MONITORING
TIME & DTC
TYPE
DEFAULT ACTIONS PRIMARY
MALF PASS
CONDITION
SECONDARY
PASS
CONDITIONS
TEST S
PROCE
Page 1 of 10
Transmission FluidOver Temperature
P0218 High transmissionfluid temperature forlong period of time
Trans Temp >130° C. 8.0V <Ignition Voltage <18.0V-39° C. <Trans Temp <149° C. for
5 sec
600 sec
Type C-
Freeze adaptsFA
Trans Temp ≤ 129° C. for 5.0
sec
Same as fail Key up and shopotentiometer b
TFT Signal andon the TCM sidtemperature to then key down.Start the engine
TFT: 35 (AP) TFT GND: 30 (
System Voltage
Low
P0562 Measured voltage at
the TCM is a belowan acceptable level
System Voltage <11V Engine Speed >1200 rpm for 5 sec 10 seconds
Type C-
None System Voltage
>11V10 sec
Same as fail
System VoltageHigh
P0563 Measured voltage atthe TCM is above anacceptable level
System Voltage >18V None 10 seconds Type C-
None System Voltage<18V10 sec
None
TransmissionControl ModuleRead OnlyMemory
P0601 EPROM/Flashmemory corruption(Incorrectprogram/calibrationschecksum)
ROM fail count >5 None Immediate
Type A
Freeze adaptsMax line pressure TCC forced off
Inhibit TCC solenoidSoft landing
FATKO
ROM fail count<5
None
TransmissionControl ModuleNot Programmed
P0602 Non-programmed TCM (calibrations)
KbCOND_NoStartCal = TRUE
None Immediate
Type A
Freeze adaptsMax line pressure TCC forced off
Inhibit TCC solenoidImmediate Landing
FATKO
KbCOND_NoStartCal =FALSE
None
TransmissionControl ModuleLong-TermMemory Reset
P0603 Wrong copy of Non-volatile Memory toRAM
Non-volatile memory(static or dynamic)checksum failure
None Immediate
Type A
Freeze adaptsMax line pressure TCC forced off
Inhibit TCC solenoid
Soft landing
FATKO
Non-volatilememory (staticor dynamic)checksum pass
TransmissionControl ModuleRandom AccessMemory
P0604 RAM failure RAM read/write failure(single word)
RAM fail count >5
None Immediate
Type A
Freeze adaptsMax line pressure TCC forced off
Inhibit TCC solenoidSoft landing
FATKO
RAM read/writepass (all words)
RAM fail count<5
7/28/2019 2006trans13_b
http://slidepdf.com/reader/full/2006trans13b 2/10
7/28/2019 2006trans13_b
http://slidepdf.com/reader/full/2006trans13b 3/10
7/28/2019 2006trans13_b
http://slidepdf.com/reader/full/2006trans13b 4/10
7/28/2019 2006trans13_b
http://slidepdf.com/reader/full/2006trans13b 5/10
7/28/2019 2006trans13_b
http://slidepdf.com/reader/full/2006trans13b 6/10
7/28/2019 2006trans13_b
http://slidepdf.com/reader/full/2006trans13b 7/10
7/28/2019 2006trans13_b
http://slidepdf.com/reader/full/2006trans13b 8/10
7/28/2019 2006trans13_b
http://slidepdf.com/reader/full/2006trans13b 9/10
7/28/2019 2006trans13_b
http://slidepdf.com/reader/full/2006trans13b 10/10
2006trans13_b .doc
SENSED
PARAMETER FAULT
CODE
ACCEPTABLE
OPERATING
RANGE AND
RATIONALITY
PRIMARY MALF
DETECTION
PARAMETERS
SECONDARY PARAMETERS
AND CONDITIONS MONITORING
TIME & DTC
TYPE
DEFAULT ACTIONS PRIMARY
MALF PASS
CONDITION
SECONDARY
PASS
CONDITIONS
TEST S
PROCE
Page 10 of 10
LostCommunicationwith BodyControlSystem(GMX001 ONLYGMT001 ONLY)
U0140 Communicationbetween TCM & BodyControl System Lost
CAN Bus BCM Error Flag=1
Ignition ON
8V <Ignition Voltage <18V for 5 seconds
Fail Count =12 out of 12(Time ≈ 12sec)
Type C
None CAN Bus BCMError flag =0
Sample Count=12 (Time ≈ 12
sec)
Same as Fail Open the CAN CAN LO(1) signat exactly the sa
CAN HI(1): 7 (HCAN LO(1): 6 (
