SCHEMATIC MANOEUVRE ILLUSTRATIONS

SCHEDULE P-07SCHEMATIC MANOEUVRE ILLUSTRATIONS

SCHEDULE P-07

P-07.01: Take-off sequence(Award only 0 or 10 points)

WIND

900 TURN

2700

TURN520m

Reversal ofpilot’s choice

15

0m

300m 1200

Upright flight

ZERO LINE - Any flying behind zero line scores zero points.If 270o turn and reversal is flown FAR outside of 60o right and left markers, score zero.Either TEN or ZERO for take-off sequence.Second attempt at take-off scores zero.

P-07.02: Half clover, with 2/4- pt. roll up and half roll down

All radii are equal.

2/4-pt. Roll on middle of the vertical line

2/4 pt. roll

P-07.02: Half clover, with 2/4- pt. roll up and half roll down

Half roll on middle of the vertical line

Upline and downline must coincide.

1/2- roll

90°

7

P-075.03: Half square loop on corner, with half rolls, exit inverted

Half rolls on middle of the lines

All radii are equal..

1/2-roll

1/2-roll

P-07.04: Reverse Cuban eight from top, 2/4-pt roll and 4/8-pt. rolls on downlines, exit inverted

All radii are equal.Rolls on middle of the lines.

2/4-pt. roll 4/8-pt. rolls

P-07.05: Half reverse Cuban eigt from top, with 2/2-pt. roll 

All radii are equal.2/2-pt. roll on middle of the line.

2/2 pt.-roll

P-07.06: 45 degrees down with 1-1/2 positive snap roll, exit inverted 

All radii are equal.

1- 1/2 positive snap roll on middle of the line.

P-07.07: Push-push-push humpty bump with half roll or 1/4 roll options, exit inverted

All radii are equal.

Half roll on middle of the line.

1/2 roll

P-07.07: Push-push-push humpty bump with half roll or 1/4 roll options, exit inverted

All radii are equal.

1/4 rolls on middle of the lines.

Option

1/4 roll 1/4 roll

8

P-07.08: Eight-point roll from inverted, exit inverted

Roll rates must be same on all points.Duration of points must be same.

P-07.09: Stall Turn, half roll up, 2/2-pt. Roll down

Half roll on middle of the line.

½ roll

P-07.09: Stall Turn, half roll up, 2/2-pt. Roll down

2/2 pt. Roll on middle of the line.2/2 pt. roll

90°

P-07.10: Loop with integrated 4-point roll on top

The 4-point roll must be integrated with the loop.

P-07.11: Immelmann turn

Half roll must be immediately after the half loop.

½ roll

All radii are equal.

P-07.12: Square loop on corner from top, with half rolls

Half rolls on middle of the lines.

All radii are equal.

P-07.13: Figure 6 with half roll

Half roll on the middle of the line.

All radii are equal.

45°

P-07.14: Hourglass, mid entry, with 2/4-pt. roll down , exit inverted

exit inverted

2/4-pt.roll on middle of the line.

2/4-pt. roll

All radii are equal.

P-07.15: Three quarter vertical eight

1/4 roll

1/2 roll1/4 roll

P-07.16: Reverse knife-edge, exit inverted

The knife-edge segments are of equal length and duration, and must be long enough to demonstrate controlled, sustained knife-edge fligt.

All radii are equal..

P-07.17: Half square outside loop, 2/4-pt. Roll up, exit inverted

2/4-pt. roll on middle of the line.

2/4-pt. roll

P-07.18: 2-1/2 turns inverted spin

Snap entry, zero points

Forced entry, downgrade.

All radii are equal.

P-07.19: Half horizontal hourglass, half roll, and two half rolls opposite in uplines

Rolls on middle of the lines. 1/2 rolltwo half rolls

opposite

The half rolls are integrated with portions of the loop.

1/2 roll1/2 roll

P-07.20: Horizontal eight from top, with integrated half rolls

The two outside loops are round.

P-07.21: Half outside loop with full roll, exit inverted

The full roll must be immediately after the half outside loop.

exit inverted

full roll

All radii are equal.

60°

P-07.22: Six-sided loop, with 2/4-pt. roll on top

2/4-pt. roll

1800

Kurve

Peter Uhlig, im Januar 2005

15

0m300m

1200

P-07.23 - Landing sequence(Award only 0 or 10 points)

WIND

1800

TURN

• If 180o turns are flown FAR outside of 60o right and left markers, score zero.• ZERO LINE - Any flying behind zero line scores zero points.• Turns must be either level or descending.• Either TEN or ZERO for landing sequence.• No hot-dogging!

Upright flight

1800 TURN

Thank you!

Have a good job!Gui Manesse May

2005